FUTABA R7006SB User Manual

1M23N31002  
FASSTest-2.4GHz Bidirectional Communication System / FASST(Multi-ch,7ch) -2.4GHz  
S.BUS2 / S.BUS Port and 6 Channels for Conventional System Receiver  
R7006SB  
Thank you for purchasing a Futaba R7006SB FASSTest-2.4GHz compatible receiver. The R7006SB receiver features bi-directional communication  
with a FASSTest Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also  
includes both standard PWM output ports (1-6ch) and S.BUS output ports. The R7006SB can also be switched the FASST(Multi-ch/7-ch) System.  
Applicable systems: Futaba FASSTest-2.4GHz / FASST (Multi-ch,7ch) -2.4GHz system transmitter  
The R7006SB has two antennas. In order to maximize signal reception  
Usage precaution  
and promote safe modeling Futaba has adopted a diversity antenna system.  
This allows the receiver to obtain RF signals on both antennas and fly  
problem-free.  
• Analog servos cannot be used with the R7006SB in the FASSTest  
12CH / FASST High-speed mode.  
WARNING  
Antenna installation for carbon fuselage  
You must leave 30mm at the tip of the antenna fully exposed. The  
exposed antenna should be secured so that it cannot move around or  
back inside of your aircraft.  
Changes or modification not especially approved by the party  
responsible for compliance could void the user’ s authority to operate the  
equipment.  
Be careful of connector insertion  
Don't connect an S.BUS servo / gyro to S.BUS2 connector.  
Link precaution  
The R7006SB receiver should be protected from vibration by foam  
rubber, Velcro, or similar mounting methods. Protect from moisture.  
Keep away from conductive materials to avoid short circuits.  
Antenna installation precaution  
Do not cut or bundle the receiver antenna wire.  
Do not bend the coaxial cable. It causes damage.  
Do not perform the linking procedure while the motor's main power  
connected or the engine is operating as it may result in serious injury.  
When the linking is complete, please cycle the receiver power and  
ensure the receiver is properly linked to the transmitter.  
The antennas must be mounted in such a way to assure they are strain  
Please power up your system in this order. Transmitter first, followed  
relieved.  
by the receiver.  
Keep the antenna as far away from the motor, ESC and other noise  
sources as you possibly can.  
Be sure that the two antennas are placed at 90 degrees to each other.  
If the R7006SB receiver was previously linked to another transmitter,  
make sure that transmitter is not operating while linking the receiver to  
the new transmitter.  
Servo for conventional  
system  
Antenna  
installation  
Compliance Information Statement  
(for U.S.A.)  
S.BUS Gyros  
S.BUS servos  
This device, trade name Futaba Corporation, model  
number R7006SB, complies with part15 of the  
FCC Rules. Operation is subject to the following  
two conditions:  
(1) This device may not cause harmful interference,  
and  
(2) This device must accept any interference  
received, including interference that may cause  
undesired operation.  
(3) This module meets the requirements for a  
mobile device that may be used at separation  
distances of more than 20cm from human body.  
To meet the RF exposure requirements of the FCC  
this device shall not be co-located with another  
Channel  
Hub  
1-6  
Telemetry sensor  
S.BUS Port (SB)  
S.BUS2 Port (SB2)  
Telemetry sensor  
S.BUS2equipment  
Hub  
R7006SB  
transmitting device.  
The responsible party of this device compliance is:  
Futaba Service Center  
The receiver power supply can  
be connected to any port.  
3002 N Apollo Drive Suite 1, Champaign, IL  
61822 U.S.A.  
When all ports are used.  
TEL (217)398-8970 or E-mail: support@futaba-rc.  
com (Support)  
Servo  
Y-harness  
Battery  
3.7 ~ 7.4V  
Switch  
LED Indication  
Link LED  
System Mode LED  
Status  
Link LED  
Red Solid  
No signal reception  
Receiving signals  
Green Solid  
Start → 2second  
later → Red Blink  
(1second)  
Red Solid  
Link/Mode  
switch  
FASSTest Green Solid  
Waiting for link  
Mode LED  
No signal reception  
Receiving signals  
Receiving signals but ID is  
unmatched  
Green Solid  
Green Blink  
Red Blink  
FASST  
Off  
-
R7006SB Specifications  
FASSTest-2.4GHz system(18ch/12ch mode)  
Waiting for link  
FASST-2.4GHz system (Multi-ch/7ch mode)  
FASSTest  
FASST  
Unrecoverable error (EEPROM, etc.)  
Alternate blink  
S.BUS2 and S.BUS port and 6ch for conventional system receiver  
• Dual antenna diversity  
• Size: 0.89 x 1.5 x 0.48 in. (22.5x38.1x12.2mm)  
• Weight: 0.28 oz. (8g)  
*When on "FASST-7ch" mode, the fail safe function can be set for 3-channel only.  
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)  
• Battery F/S Voltage: FASSTest---It sets up with a transmitter  
FASST---3.8V  
*Be sure that when using ESCs regulated output the capacity of the ESC must meet your us-  
age condition.  
*Never use dry batteries for the power supply of the R7006SB as they may cause difficulties.  

Trane Genius Pkg Prc007 En User Manual
Tally Genicom Tally Dot Matrix 2900 User Manual
Sharp Cv 2p10sc User Manual
Schumacher Sf 2150ma User Manual
Sanyo Eco G Spw Gu105xh User Manual
FUJITSU FI 6130Z User Manual
DELL VOSTRO 3450 02 User Manual
CRAFTSMAN 536.886440 User Manual
CRAFTSMAN 536.292510 User Manual
ACER EX 13H User Manual