FUTABA R6208SB User Manual

S.BUS compatible/FASST-2.4GHz (Multi-ch) system  
8 channels/high-speed receiver  
R6208SB  
Thank you for purchasing a Futaba  
compatible receiver.  
R6208SB S.BUS  
Usage condition on "High Speed mode"  
CAUTION  
The  
has an  
system output port and a  
S.BUS  
R6208SB  
conventional system channel output. It can also be used with  
conventional system servos, etc. in addition to  
compatible servos and gyros, etc.  
When using the high-speed mode, use a Futaba  
digital servo (including brushless servo) or S.BUS  
servo at conventional system use channels 1 to 6.  
Analog servos cannot be used.  
system  
S.BUS  
In addition, the operating mode (high-speed mode/normal  
mode) can be selected.  
* However, channel outputs 7 and 8 for conventional system oper-  
• The use of analog servos may cause servo trouble.  
• When using analog servos, select the normal mode, and  
ate in the normal mode even if set to the high-speed mode.  
use channel outputs 7 and 8.  
(on 8ch mode)  
(on multi-ch mode)  
(on 8ch mode)  
(on  
T8FG 2.4GHz  
, TM14  
, TM8  
, T10CG 2.4GHz  
Applicable systems:  
10ch mode)  
(on 10ch mode)  
, TM10  
Link/Mode switch  
• Channel outputs for conventional  
system (1 to 8)  
DATA port  
• Battery terminal (B)  
S.BUS Port (S.BUS)  
LED  
R6208SB  
Compliance Information Statement  
(for U.S.A.)  
R6208SB Specifications  
S.BUS compatible/FASST-2.4GHz (Multi-ch) system/8 channels/  
high-speed receiver  
This device, trade name Futaba Corporation of America, model  
number R6208SB, complies with part15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including  
interference that may cause undesiredoperation.  
• Dual antenna diversity  
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)  
• Weight: 0.49 oz. (13.8g)  
• Power requirement: 3.7V to 7.4V  
(Voltage range: 3.5 to 8.4V)  
The responsible party of this device compliance is:  
Futaba Service Center  
*Be sure that when using ESC's regulated output the capacity of the ESC  
must meet your usage condition.  
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.  
TEL (217)398-8970 or E-mail: [email protected] (Support)  
*The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S  
function doesn't work properly when other type battery is used.  
What is S.BUS?  
Different from conventional radio control systems the  
30 degrees” to multiple devices. The  
devices execute  
S.BUS  
S.BUS  
system uses data communication to transmit control signals  
from a receiver to a servo, gyro, or other compatible  
only those commands for their own set channel. For this  
reason, it can be used by connecting multiple servos to the  
same signal line.  
S.BUS  
device. This data includes commands such as “move the  
channel 3 servo to 15 degrees, move the channel 5 servo to  
[Connection by S.BUS system]  
3ch  
5ch  
Ch output/  
Battery terminal  
R6208SB  
S.BUS hub  
S.BUS hub  
6ch  
S.BUS  
S.BUS output  
2ch  
4ch  
Battery  
S.BUS servo  
Conventional  
servo  
* Can also be used together with conventional servos.  
* When using servos with a remote battery pack, use S.BUS Hub with Cable (2-way/remote battery pack use).  
Please refer to the instruction manual of S.BUS Hub with Cable (2-way/remote battery pack use) for the connection method.  

Whirlpool Acm184xa0 User Manual
Wachsmuth Krogmann Mw5798 User Manual
Samsung Sf3000t User Manual
Samsung Sc12zb1 User Manual
Ricoh Aficio Sp C222sf User Manual
MAKITA LS800DWA User Manual
KENWOOD KRF V5560D 02 User Manual
HAYWARD HEATPRO HP20854T User Manual
CRAFTSMAN 137.218040 User Manual
BROTHER FAX 2480C User Manual