FUTABA R3008SB User Manual

1M23N17481  
T-FHSS Air-2.4GHz Bidirectional Communication System  
S.BUS2 / S.BUS Port and 8 Channels for Conventional System Receiver  
R3008SB  
Thank you for purchasing a Futaba R3008SB T-FHSS Air-2.4GHz compatible receiver. The R3008SB receiver features bi-directional communication  
with a T-FHSS Air-2.4GHz Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized.  
It also includes both standard PWM output ports and S.BUS output ports.  
Applicable systems: Futaba T-FHSS Air-2.4GHz system transmitter  
Be sure that the two antennas are placed at 90 degrees to each other.  
Usage precaution  
• The R3008SB has two antennas. In order to maximize signal reception  
and promote safe modeling Futaba has adopted a diversity antenna  
system. This allows the receiver to obtain RF signals on both antennas  
and fly problem-free.  
• Futaba T-FHSS Air system does not work with current Futaba T-  
FHSS / S-FHSS / FHSS / FASST / FASSTest system.  
• The R3008SB receiver can only be used with T-FHSS Air capable  
transmitters.  
• Don't connect Extra Voltage before turning on a receiver.  
Antenna installation for carbon fuselage  
WARNING  
WARNING  
Changes or modification not expressly approved by the party  
responsible for compliance could void the user’s authority to operate the  
equipment.  
You must leave 30mm at the tip of the antenna fully exposed. The ex-  
posed antenna should be secured so that it cannot move around or back  
inside of your aircraft.  
DANGER  
The R3008SB receiver should be protected from vibration by foam  
rubber, Velcro or similar mounting methods. Protect from moisture.  
S.BUS2 precaution  
DANGER  
5HFHLYHU  
Keep away from conductive materials to avoid short circuits.  
Don't connect a connector, as shown right.  
Antenna installation precaution  
Don't cut or bundle the receiver antenna wire.  
• It will be a short-circuit, if it connected in  
Do not insert either a switch  
or battery in this manner.  
this way. A short circuit across the battery  
terminals may cause abnormal heat, fire  
and burning.  
Don't bend the coaxial cable. It causes damage.  
Don't connect servo for conventional system to S.BUS/S.BUS2 port.  
The antennas must be mounted in such a way to assure they are  
strain relieved.  
• Digital servo for conventional system It does not operate.  
• Analog servo It may cause abnormal heat, fire and burning.  
Keep the antenna as far away from the motor, ESC and other noise  
sources as you possibly can.  
WARNING  
Only S.BUS2 capable devices may be connected the S.BUS2 port.  
Standard S.BUS servos and gyros should not be connected the S.BUS2  
port.  
(Antenna installation)  
90˚  
(Typical installation)  
CH Mode B  
([WUDꢂ9ROWDJH  
3RUW  
It connects the battery  
6ꢀ%86ꢂ6HUYR  
for power, etc.  
6HUYRꢂIRU FRQYHQWLRQDO  
6ꢀ%86ꢂ*\UR  
External voltage input  
V\VWHP  
cable of an option is  
used. The voltage of  
the battery can be  
displayed with a  
transmitter.  
%DWWHU\ꢂWRꢂꢇꢈ%  
&KDQQHOꢅꢂRXWSXW  
&KDQQHOꢆꢂRXWSXW  
6ꢀ%86ꢂ+8%  
/('  
Please refer the table below  
for LED status vs receiver's  
0RGHꢂVZLWFK  
ꢃ,WꢂLVꢂQRWꢂXVHGꢂIRUꢂDꢂOLQNꢀꢄ  
condition.  
6ꢀ%86ꢂSRUW ꢀꢁꢂ6%
ك
 
7HOHPHWU\ꢂ6HQVRU  
7HOHPHWU\ꢂ6HQVRU  
7HOHPHWU\ꢂ6HQVRU  
LED Indication  
6ꢀ%86ꢁ  
SRUW  
Green  
Off  
Red  
Status  
5ꢀꢁꢁꢂ6%  
Battery(7/B)  
$QWHQQD  
ꢀ6ꢃ%86ꢄ
ك
 
Solid No signal reception  
Off Receiving signals  
6ꢀ%86ꢂ+8%  
Solid  
Alternate blink Unrecoverable error (EEPROM, etc.)  
S.BUS2  
6ꢀ%86ꢂ+8%  
Compliance Information Statement  
(for U.S.A.)  
6ꢀ%86ꢂ+8%  
This device, trade name Futaba Corporation, model number R3008SB, complies with  
part15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
*Default setting S.BUS,  
don't connect servo for  
conventional system.  
S.BUS(8/SB)  
6ꢀ%86ꢂꢁꢂꢃ69ꢄꢂ6HUYR  
6ꢀ%86ꢂꢁꢂ*\UR  
(2) This device must accept any interference received, including interference that may  
cause undesired operation.  
(3) This module meets the requirements for a mobile device that may be used at separation  
distances of more than 20cm from human body.  
To meet the RF exposure requirements of the FCC this device shall not be co-located with  
another transmitting device.  
The responsible party of this device compliance is:  
Futaba Service Center  
5ꢀꢁꢁꢂ6%ꢃ6SHFLÀFDWLRQV  
T-FHSS Air-2.4GHz system/S.BUS2 and S.BUS port and 8 channels for  
conventional system receiver  
• Dual antenna diversity  
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.  
TEL (217)398-8970 or E-mail: [email protected] (Support)  
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)  
• Weight: 0.36 oz. (10.1g)  
• Power requirement: 4.8V to 7.4V  
本產品符合低功率電波輻射性電機管理辦法 第十二條、第十四條等條文規定  
• Battery F/S Voltage: It sets up with a transmitter  
1. 經型式認證合格之低功率射頻電機,非經許可,公司、商  
號或使用者均不得擅自變更頻率、加  
大功率或變更原設計之特性及功能。  
• Extra Voltage port: 0 70V DC  
2. 低功率射頻電機之使用不得響飛航安全及干擾合法通信發現有干擾現象時,應立即停用,  
* Be sure that when using ESCs regulated output the capacity of the ESC must  
並改善  
至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率  
射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。  
meet your usage condition.  

Unitech Magnetic Stripe Reader Msr102 User Manual
Soleus Air Kfhip 09 Od User Manual
Sanyo Cadnica Kr 2000c User Manual
Sanyo 26thw72r User Manual
NEC NP M361X User Manual
Mitsubishi Electronics City Multi Puhy Ymc User Manual
LG CINEBEAM AI THINQ HU710PW GL User Manual
JENSEN JE2608WV User Manual
HP 9000 RP8440 User Manual
BLACK DECKER BDCDD220C User Manual