FUJITSU FI 5750C User Manual

P3PC-E737-02EN

fi-5750C Image Scanner

Getting Started

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is located.

■ Introduction

Thank you for purchasing the fi-5750C Duplex

Color Scanner product.

• Consult your dealer or an experienced

radio/TV technician.

This document describes how to handle fi-

5750C Duplex Color scanner and basic opera-

tion methods. Before you start using fi-5750C

Duplex Color scanner, be sure to thoroughly

read this manual to ensure correct use.

FCC warning: Changes or modifications not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

• The use of a shielded interface

The “Operator’s Guide” is guide is stored on

the User Manual CD-ROM. The guide pro-

vides useful and detailed information on opera-

tion, daily care, replacement of consumables

and trouble shooting, etc. Please also read the

Operator’s Guide for your reference.

ATTENTION

cable is required to comply with

the Class B limits of Part 15 of

FCC rules.

• The length of the AC cable must

be 3 meters (10 feet) or less.

Canadian DOC Regulations

■ Regulatory Information

This digital apparatus does not exceed the

Class B limit for radio noise emissions from

digital apparatus set out in the Radio interfer-

ence Regulations of the Canadian Department

of Communications.

FCC declaration

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a res-

idential installation. This equipment generates,

uses, and can radiate radio frequency energy

and, if not installed and used in accordance

with the instruction manual, may cause harm-

ful interference to radio communications.

However, there is no guarantee that interfer-

ence will not occur in a particular installation.

If this equipment does cause harmful interfer-

ence to radio or television reception, which can

be determined by turning the equipment off

and on, the user is encouraged to try to correct

the interference by one or more of the follow-

ing measures:

This Class B digital apparatus complies with

Canadian ICES-003.

Le présent appareil numérique n'émet pas de

parasites radioélectriques dépassant les limites

applicables aux appareils numériques de la

classe B et prescrites dans le Règlement sur le

brouillage radioélectrique dictées par le Min-

istère des Communications du Canada.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

Bescheinigung des

Herstellers / Importeurs

• Reorient or relocate the receiving

Für den fi-5750C wird folgendes bescheinigt:

antenna.

• Increase the separation between the

• In Übereinsstimmung mit den Bestimmun-

equipment and receiver.

gen der EN45014(CE) funkentstört .

• Maschinenlärminformationsverordnung 3.

GPSGV: Der höchste Schalldruckpegel

beträgt 70 dB (A) oder weniger, gemäß EN

ISO 7779.

transport systems, medical equipment for

sustaining life, and missile firing control in

weapons systems, and when provisionally the

safety in question is not ensured. The user

should use this product with adopting measures

for ensuring safety in such high-safety

applications. PFU LIMITED assumes no

liability whatsoever for damages arising from

use of this product by the user in high-safety

applications, and for any claims or

International ENERGY STAR

Program

As an ENERGY

compensation for damages by the user or a

third party.

STAR Partner, PFU

LIMITED has deter-

mined that this product

meets the ENERGY

About the use of mercury

STAR guidelines for

energy efficiency.

The scanner lamp contains mercury.

To avoid unexpected injury, read the following

carefully.

The International ENERGY STAR Office

Equipment Program is an international

program that promotes energy saving through

the penetration of energy efficient computers

and other office equipment. The program backs

the development and dissemination of products

with functions that effectively reduce energy

consumption. It is an open system in which

business proprietors can participate voluntarily.

The targeted products are office equipment

such as computers, monitors, printers,

Doing the following actions may result in seri-

ous personal injuries:

• Do not put the substance in the lamp in

your mouth as it contains mercury.

• Do not incinerate, crush, or shred the

scanner.

• Do not breathe the chemical liquid

contained in the scanner parts.

facsimiles, copiers, scanners, and

multifunction devices. Their standards and

logos are uniform among participating nations.

Disposing of the scanner should be conducted

as required by local ordinances or regulations.

Trademarks

Use in High-safety

Applications

Microsoft, Windows, and Windows NT are

registered trademarks of Microsoft Corporation

in the United States and/or other countries.

Adobe, the Adobe logo, and Acrobat are either

registered trademarks of Adobe Systems Incor-

porated in the United States and/or other coun-

tries.

ISIS and QuickScan are trademarks or regis-

tered trademarks of EMC Corporation in the

United States.

This product has been designed and

manufactured on the assumption that it will be

used in office, personal, domestic, regular

industrial, and general-purpose applications. It

has not been designed and manufactured for

use in applications (simply called "high-safety

applications" from here on) that directly

involve danger to life and health when a high

degree of safety is required, for example, in the

control of nuclear reactions at nuclear power

facilities, automatic flight control of aircraft,

air traffic control, operation control in mass-

Other product names are the trademarks or reg-

istered trademarks of the respective companies.

How Trademarks Are

Indicated In This Manual

Manufacturer

PFU LIMITED

References to operating systems (OS) are

indicated as follows:

International Sales Dept., Imaging Business

Division, Products Group

Windows 95:

Microsoft Windows 95

operating system.

Solid Square East Tower, 580 Horikawa-cho,

Saiwai-ku, Kawasaki-shi Kanagawa 212-8563,

Japan

Windows 98:

Microsoft Windows 98

operating system.

Phone : (81-44) 540-4538

Windows Me: Microsoft Windows Mil-

lennium Edition operating

system.

LIMITED 2006.

Windows 2000: Microsoft Windows 2000

Professional operating

system.

■ Note, Liability

Windows XP: Microsoft Windows XP

Professional operating

READ ALL OF THIS MANUAL

CAREFULLY BEFORE USING THIS

PRODUCT. IF THIS PRODUCT IS NOT

USED CORRECTLY, UNEXPECTED

INJURY MAY BE CAUSED TO USERS OR

BYSTANDERS.

system,

Microsoft Windows XP

Home Edition operating

system.

While all efforts have been made to ensure the

accuracy of all information in this manual,

PFU assumes no liability to any party for any

damage caused by errors or omissions or by

statements of any kind in this manual, its

updates or supplements, whether such errors

are omissions or statements resulting from

negligence, accidents, or any other cause. PFU

further assumes no liability arising from the

application or use of any product or system

described herein; nor any liability for

Windows NT: Microsoft Windows NT

Server operating system

Version 4.0,

Microsoft Windows NT

Workstation operating

system Version 4.0.

Where there is no distinction between the dif-

ferent versions of the above operating system,

the general term "Windows " is used.

incidental or consequential damages arising

from the use of this manual. PFU disclaims all

warranties regarding the information contained

herein, whether expressed, implied, or

statutory.

iii

Symbols Used In This Manual

■ Preface

This manual uses the following symbols in

explanations in addition to warning

indications.

Safety Precautions

This manual describes important details for

ensuring the safe and correct use of this

product. Thoroughly read this manual before

you start to use this product. In particular, be

sure to read and fully understand the Safety

Precautions described in this manual before

you use this product.

This symbol alerts operators to

particularly important information. Be

ATTENTION

sure to read this information.

Also, store this manual in a safe place so that it

can be easily referred to during use of this

product.

This symbol alerts operators to helpful

advice regarding operation.

HINT

Warning Indications Used In

This Manual

A TRIANGLE symbol indicates

that special care and attention is

required.

The drawing inside the triangle

shows the specific caution.

This manual uses the following indications to

ensure safe and correct use of this product, and

to prevent possible danger and injury to the

operator and other persons.

A CIRCLE with a diagonal line

inside shows action which users

may not perform.

The drawing inside or under the

circle shows the specific action

that is not allowed.

WARNING

This indication alerts operators to an operation

that, if not strictly observed, may result in

severe injury or death.

Outline characters on a colored

background show instructions

users should follow.

It may also include the drawing

that shows the specific instruc-

tion.

CAUTION

This indication alerts operators to an operation

that, if not strictly observed, may result in

safety hazards to personnel or damage to

equipment.

Screen Examples In This

Manual

The screen examples in this manual are subject

to change without notice in the interest of

product improvement.

If the actual displayed screen differs from the

screen examples in this manual, operate by

following the actual displayed screen while

referring to the User's Manual of the scanner

application you are using.

Furthermore, the screenshots in this manual are

for FUJITSU TWAIN 32 scanner driver,

ScandAll 21 Image Capturing Utility Software,

Use this scanner only at the indicated

power voltage. Do not connect to

multiple-power strips.

™

FUJITSU ISIS scanner driver, QuickScan

image capturing software and Adobe Acrobat.

Use this scanner only at the indi-

cated power voltage and cur-

rent. Improper power voltage

and current might cause fire or

electric shock.

Also, do not connect to multiple-

power strips.

About Maintenance

The user must not perform repairs on this

scanner.

Contact the store where you purchased the

scanner or an authorized FUJITSU Image

Scanner service provider to make repairs to this

product.

Wipe any dust from the power plug.

Wipe off any dust from metal

parts on the power plug or metal

fittings with a soft, dry cloth.

Accumulated dust might cause

fire or electric shock.

■ Safety Precautions

Do not install in locations subject to

oil smoke, steam, humidity, and dust.

WARNING

Do not install the scanner in

locations subject to oil smoke,

steam, humidity, and dust. Doing

so might cause a fire or electric

shock.

The following describes important warnings

described in this manual.

Do not touch the AC cable with wet

hands.

Do not use the scanner if you smell

strange odor.

Do not touch the power plug

with wet hands. Doing so might

cause electric shock.

If you detect heat coming from

the device or detect other prob-

lems such as smoke, strange

smells or noises, immediately

turn off the scanner and then dis-

connect its power plug.

Make sure that the smoking has

stopped, and then contact the

store where you bought the

scanner or an authorized

FUJITSU scanner service

provider.

Do not damage the AC cable.

A damaged AC cable may cause

fire or electric shock.

Do not place heavy objects on

AC cables, or pull, bend, twist,

heat, damage or modify AC

cables.

Also, do not use damaged AC

cables or power plugs, and AC

cables or power plugs when the

wall socket is loose.

Turn the scanner OFF if it is

damaged.

If the scanner is damaged for any

reason, turn off the scanner and

unplug the power cable before

contacting the store where you

purchased the scanner.

Use only specified AC cables and

connector cables

Use only specified AC cables

and connector cables. Failure to

use the correct cables might

cause electric shock and

equipment failure.

Install the scanner on a strong

surface that will support the

weight of the scanner and other

devices.

Do not put liquids inside the scanner.

Do not insert or drop metal

objects in to the scanner.

Do not scan wet documents or

documents with paper clips or

staples.

Firmly insert the power plug.

Do not splash or allow the scan-

ner to get wet.

Firmly insert the power plug into

the power outlet as far it can go.

If foreign objects (water, small

metal objects, liquids, etc.) get

inside the scanner, immediately

turn off the scanner and

disconnect the power plug from

the power outlet, then contact

the store where you bought the

scanner or the Maintenance

Service Center.

Do not block the ventilation ports.

Do not block the ventilation

ports. Blocking the ventilation

ports generates heat inside of

scanner, which may results in

fire or scanner failure.

Pay particular attention to this

warning in households where

there are small children.

Do not place heavy objects or climb

on top of the scanner.

Do not place heavy objects on

the scanner or use the scanner's

top surface for performing other

work. Improper installation

might cause injuries.

Do not touch the inside of the

scanner unless necessary.

Do not take apart or modify the

scanner. The inside of the

scanner contains high-voltage

components. Touching these

components might cause fire or

electric shock.

Before moving the scanner,

disconnect the power plug from the

power outlet.

Do not move the scanner with

the power and interface cables

connected as this might damage

the cables, causing fire, electric

shock or injuries.

Before moving the scanner, be

sure to disconnect the power

plug from the power outlet, and

disconnect data cables. Also,

make sure that the floor is free of

obstructions.

CAUTION

The following describes important cautions

described in this manual.

Do not install the scanner on unsta-

ble surfaces.

Install the scanner on a desk so

that none of its parts protrude

outside of the desktop. Also,

make sure that the scanner is

installed on a flat, level surface.

Do not install the scanner on

unstable surfaces. Install the

scanner on a level surface that is

free of vibration to prevent it

from falling.

Do not use the scanner immediately

after moving it from a cold place into

a warm room.

Do not use the device immedi-

ately after moving it from a cold

place into a warm room. This

may cause condensation, which

might lead to scanning errors.

Let the device dry about one or

two hours before you use it.

Protect the scanner from static

electricity.

Before moving the scanner, make

sure the shipping lock and the ADF

lock screws are locked.

Install the scanner away from

strong magnetic fields and other

sources of electronic noise. Also,

protect the scanner from static

electricity as this might cause the

scanner to malfunction.

When moving the scanner, be

sure to lock the shipping lock

and the ADF lock screws in

order to prevent damages to the

scanner.

Do not use aerosol sprays near the

scanner.

Do not use aerosol sprays to

clean the scanner. Aerosol

sprays cause dirt and dust to

enter the scanner, resulting

scanner failure and malfunction.

Avoid any contact when scanner is in

use.

Avoid touching any scanner

mechanism when scanning as

this may cause injuries.

Disconnect the power plug from the

power outlet when the scanner is not

used for a long period of time.

When the scanner is not used for

a long period of time, be sure to

disconnect the power plug from

the power outlet for safety.

Do not install the scanner in the

direct sunlight.

Do not install the scanner in the

direct sunlight or near heating

apparatus. Doing so might cause

excessive heat to build up inside

the scanner, causing fire or scan-

ner trouble. Install the scanner in

a well-ventilated location.

Do not try to move or lift the scanner

alone.

This scanner is heavy (77.2lbs/

35kg). When you carry the scan-

ner, ensure that additional per-

sonnel are used.

vii

viii

Contents

Introduction................................................................. i

Regulatory Information ............................................... i

Note, Liabilit y ............................................................ iii

Prefac e ..................................................................... iv

Safety Precautions .................................................... v

Chapter1

Chapter 2

Appendix

PREPARING THE SCANNE R ..... 1-1

1.1

1.2

1.3

Checking the contents of scanner package.............1-2

Names and function of parts....................................1-2

Functions of the operator panel...............................1-3

INSTALLATION OF THE SCANNER ... 2-1

2.1

2.2

2.3

Installing the scanner...............................................2-2

Connecting the scanner to your PC.........................2-2

Installing the Scanner Application ...........................2-4

....................................................AP-1

Appendix 1Troubleshooting ............................................... AP-2

Appendix 2Daily Care

................................................... AP-6

Appendix 3Replacing Consumable s .................................. AP-8

Appendix 4Setting the position of the ADF ........................ AP-9

Chapter1 PREPARING THE SCANNER

1.1 Checking the contents of scanner package 1-2

1.2 Names and function of parts ...................... 1-2

1.3 Functions of the operator panel .................. 1-3

1-1

TABLE 1.

1.1 Checking the contents of

scanner package

No.

Name

Function

Screw Storage

Holes

Holes in where the ADF

Lock Screws are placed

after unlocking the ADF.

When you unpack the scanner package, make sure

that the package contains all the parts on the list

included in the package.

Handle

Used to open/close the

Document Cover.

If any parts are missing or defective, contact your

sales representative. Handle the scanner and

accessories with care.

• Front

1.2 Names and function of

parts

This section describes the names of parts and their

functions.

• Front (Flat Bed unit opened view)

TABLE 2.

No.

Name

Function

Operator Panel

This panel consists of a

Function No. display,

four buttons and a LED.

ADF Paper

Chute

For scanning documents

with the ADF scanning,

place the document here

adjusting the side guides

to the document width.

Shipping Lock

ADF Button

Used to fix the Flatbed’s

carrier unit in order to

prevent damages during

transportation.

TABLE 1.

Press this button to open

the ADF.

No.

Name

Function

ADF

It transports a document

to the reading position

automatically. According

to need, this unit can be

set in three directions by

turning and sliding it.

Document

Cover

When closed, this cover

fixes the document set on

the reading position.

(Automatic

Document

Feeder)

Document Bed

For scanning documents

with the Flat bed, place

the document here.

Stacker

Scanned documents are

ejected from the ADF

onto this tray. It is

possible to change the

height.

Document

Holding Pad

It fixes the document by

pressing it onto the

document bed.

ADF Lock

Screws

Used to fix the ADF.

They are securing the

ADF during

transportation.

1-2

•

Rear

• ADF

TABLE 3.

No.

Name

Function

EXT connector Connector port for

optional units.

USB Interface

Connector

Used for connecting a

USB interface cable from

a PC.

SCSI Interface

Connector

Used for connecting a

SCSI interface cable

from a PC.

SCSI ID

Switch

Used for setting SCSI ID

(The setting at the factory

shipment is ID=5).

Third Party

Slot (Optional

Slot)

The slot for an option

board.

TABLE 4.

No.

Name

Side Guide

Button

Used for adjusting the

side guides.

Chute Roller

Pick Arm

Power Inlet

Used for connecting a

power cable from the

power outlet.

Pick Roller Set

Brake Roller

Feed Roller

Plastic Roller

Sheet Guide

Power Switch

Used for turning ON/

OFF the scanner.

Ultra Sonic Sensor (Multi feed detection)

Glass

1.3 Functions of the operator

panel

The Operator Panel is located at the right side

of the scanner. This panel consists of a function

number display, buttons and a LED.

1-3

You can change the overlay on the opeartor

panel according to your language.

Indications on the

Function No. display

The following shows the indications on the

Function No. display.

• 8

Blinks only one time upon turning on the scanner.

•

Indicates that the scanner has been turned ON and is

being initialized.

•

Indicates that initialization will soon be completed.

TABLE 5.

Indicates that initialization has been completed

successfully.

This status is called "Ready Status".

Name

Function

Function No. display

Indicates the function No.

and error status.

•

Buttons

Function

Changes the Function

activated by the Send to

button .

Indicates that a temporary error (that users can solve)

has occurred during the initialization or scanning of

documents.

"U" and an error number (0, 1, 2, 4) are displayed

alternately. To return the scanner to the ready status

("1"), press the "Scan" or "Send to" button while the

error is indicated.

Send to

Scan

Launches the linked

application software

LED

Power

Lights when the scanner

is turned ON.

•

For details, refer to the "FUJITSU TWAIN32

Scanner Driver User’s Guide", provided in the

User Manual CD-ROM, and the "fi-5750C

Operator's guide", provided in the Setup CD-

ROM.

Indicates that a device alarm (that users cannot solve)

has occurred during the initialization or scanning of

documents.

"E" and an "alarm code" (a number or letter) are

indicated alternately. To return the scanner to the

ready status ("1"), press "Scan" or "Send to" button

while the alarm is indicated.

If this alarm occurs, turn the power off and then on

again. If the alarm is indicated after turning on the

power again, contact an authorized FUJITSU scanner

service provider.

1-4

Chapter 2 INSTALLATION OF THE SCANNER

2.1 Installing the scanne r.............................................2-2

2.2 Connecting the scanner to your P C.......................2-2

2.3 Installing the Scanner Application..........................2-4

2-1

Setting the Stacker

2.1 Installing the scanner

Mount the Stacker onto the scanner

aligning the protrusions to the holes on the

scanner.

You can fix the stacker at two positions: the

upper position or the lower position.

Place the scanner at its installation site.

For details on the scanner’s dimensions

and required installation space, refer to "10

SCANNER SPECIFICATION" in the "fi-

5750C Operator's guide".

Unlock the Shipping Lock.

After placing the scanner to the installation

site, switch the Shipping Lock into the

opened (unlocked) position.

Connecting the Power cable.

Horizontal position: Lock

Vertical position: Unlock

Remove the ADF Lock Screws.

After placing the scanner to the installation

site, remove the ADF Lock Screws and

place them into the Storage Holes. For

more details about positioning of the ADF

refer to "Appendix 4 Setting the position of

the ADF" on page 9.

Setting the ADF Paper Chute.

Use only the AC cable included the

scanner package.

ATTENTION

Hold the ADF paper chute and insert

its tabs into the holes on the rear side

of the ADF as shown in the figure

below so that the side guides facing

upwards.

Connect the Power cable to a power

outlet.

2.2 Connecting the scanner to

your PC

When running Windows 95 and/or Windows

NT 4.0, connect the scanner to your PC with

the SCSI interface cable. When running Win-

dows 98, Windows Me, Windows 2000 and/or

2-2

Windows XP, connect the scanner to your PC

with either the USB or the SCSI interface

cable.

Connecting the SCSI

interface cable

When using the scanner with the SCSI inter-

face, you need to purchase a commercially

available SCSI cable and a SCSI card.

Do not connect both the USB interface

cable and the SCSI cable at the same

ATTENTION

time. It is not possible to use the USB

interface with Windows 95 and/or

WindowsNT 4.0.

• SCSI cable

The SCSI has to fit to a 50 Pin half pitch connector

and the SCSI card connector of your PC.

Connecting the USB Cable

• SCSI card

Use the recommended SCSI card noted on the fol-

lowing website:

Please connect a USB cable to the

Scanner.

http://imagescanner.fujitsu.com/

Connect the USB interface cable to the

USB interface connector of the scanner.

When connecting the SCSI interface

cable, be sure to first connect the SCSI

ATTENTION

interface cable then turn on the scanner

and your PC. Connect the scanner so

that it is the terminated device on the

SCSI daisy chain.

Connect the SCSI cable to the scanner.

Connect the SCSI cable to the SCSI

interface connector and make sure it is

firmly connected.

Please connect the other end of the

cable to your PC.

Turn ON the scanner.

Turn ON your PC.

Connect the other end of the cable to

your PC.

Use the USB interface cable provided as

an accessory for the scanner. Operation

ATTENTION

with a commercially available USB cable

is not guaranteed. When connecting to a

USB hub, be sure to connect to the hub

nearest your computer (first stage). If you

connect it to a USB hub from the second

stage onwards the scanner may not

operate correctly.

For setting the SCSI ID of the scanner,

please refer to the following section.

HINT

Setting the SCSI ID

The factory default setting for SCSI ID is "ID 5". If the

SCSI ID of another device has already been set to the

same ID, change either the scanner's SCSI ID or that of

2-3

the other device. To change the SCSI ID see the

following procedure.

2.3.1 For Fujitsu Twain 32

Scanner Driver

Turn the scanner OFF.

Preparation

Set the SCSI ID.

Before installing the application, please

confirm the following items:

Set the device address by using the SCSI

ID switch on the rear of the scanner.

• Keep the Setup CD-ROM at hand.

• Confirm if the scanner is connected to

your PC correctly.

• If an older version of the FUJITSU

TWAIN 32 Driver has already been

installed, please uninstall it before

installing the new one.

• There are two types of FUJITSU TWAIN

32 Drivers. Depending on the operating

system (OS) of the computer, the most

appropriate driver will be installed

automatically.

TABLE 1.

No.

Description:

• For Windows 98, Windows Me,

Windows 2000, Windows XP:

0 - 7

8, 9

Can be set as the ID.

FUJITSU TWAIN32 V9

Used for the factory default value

(SCSI ID=5).

• For Windows 95 and Windows

NT 4.0:

FUJITSU TWAIN32 V8

Turn ON the Scanner.

• When using Windows 95 or Windows

NT 4.0: ASPI Manager 4.01 or later is

required (generally comes with SCSI

board products).

When the scanner is turned ON, the SCSI

ID set at step 2 is enabled.

Turn ON your PC.

For details on connecting the scanner,

refer to "2.1 Installing the scanner" on

HINT

page 2 in this manual.

2.3 Installing the Scanner

Application

For scanning documents with this scanner, the

scanner driver as well as an image capturing

application software (called "application" here-

after) must be installed on your PC.

Uninstall [Scanner Utility for Microsoft

Windows] in [Add/Remove Programs] of

ATTENTION

the control panel.

Scanner driver:

FUJITSU TWAIN 32 Scanner Driver

FUJITSU ISIS Scanner Driver

Application:

ScandAll 21 (for TWAIN)

QuickScan Pro (for ISIS)

2-4

Click [Install Products].

Installing the FUJITSU

TWAIN32 Scanner Driver

Windows XP screenshots are used in this

section. The windows and operations

may slightly vary depending on your OS.

HINT

Turn the scanner ON.

Turn on your PC and log on to

Windows.

Click [TWAIN Driver] on the window

below.

When using Windows NT 4.0, Windows

2000 or Windows XP, log on as a user

ATTENTION

with "Administrator" privileges (privileges

of the administrator of your PC)

The scanner may be detected

automatically. If so, [Found New

HINT

Hardware Wizard] (or [Add/Remove

Hardware Wizard]) dialog box will

appear. Click [Cancel] to close the

Wizard window.

Error Recovery Guide Installation win-

dow appears.

Error Recovery Guide is a software that

displays troubleshooting information on

screen if any scanner error occurred.

Although you do not install this software,

the performance of the scanner would not

be affected. However it is recommendable

to install this software.

Insert the Setup CD-ROM into the CD

drive.

When you select [Yes] for installing Error

Recovery Guide, [Choose Setup

Language] window appears. Select a

language and follow the instructions on

the window. Error Recovery Guide will

automatically start on finishing its

installation. Please wait until the

installation of TWAIN driver automatically

starts.

The <SETUP DISK START UP SCREEN>

will be displayed.

ATTENTION

This screen may not appear when the

"Autoplay" setting of your PC is OFF. In

this case, run "Install.exe" in this CD-

ROM directly by the "Explorer" or "My

Computer".

ATTENTION

2-5

2. When any alarm is displayed on [Hard-

ware Installation] window, click the

[Continue Anyway] button.

Select a language used for installa-

tion on [Choose Setup Language]

window and click [OK].

3. Click the [Finish] button.

Now the installation of the scanner driver is

completed.

For confirming if the installation was

successful, perform a scanning operation

ATTENTION

by using an application that complies with

the TWAIN standard such as ScandAll

21.

Install the application following the

instructions on the window.

When the [InstallShield Wizard Com-

plete] window appears, click [Finish].

Installing ScandAll 21

ScandAll 21 is an imaging software, conform-

ing with the TWAIN standards. With the

FUJITSU TWAIN 32 scanner driver you can

capturescannedimagedatafromthescanner.

When using Windows NT 4.0, Windows

2000 and/or Windows XP, please login as

ATTENTION

a user with "Administrator" privileges

(privileges of the administrator of your

PC).

Insert the Setup CD-ROM in your CD-

drive

Your computer is restarted and the

scanner will be detected.

10.

The, <SETUP DISK STARTUP SCREEN>

will be displayed.

Do not remove the Setup

CD-ROM from the CD drive until your PC

will be completely restarted.

Click [Install Products].

Depending on the OS, the following

operations may be necessary.

ATTENTION

For Windows 98:

When a request for inserting the CD-

ROM of Windows 98 appears, insert it

into the CD drive and click the [OK]

button.

For Windows 2000:

When [Digital Signature not Found]

appears, click [Yes].

For Windows XP

1. When [Found New Hardware Wizard]

appears, confirm that the Setup

CD-ROM is set in the CD drive, then

click the [Next] button.

2-6

Click [ScandAll 21].

Confirming the installation

Set your documents into the ADF Paper

Chute.

For the loading of documents, please refer

to 2.4 "Scanning documents" of the "fi-

5750C Operator's Guide".

Start ScandAll 21

From the [Start] Menu, select [Program]-

[Scanner Utility for Microsoft Windows]-

[ScandAll 21].

Select an appropriate language from

the <Choose Setup Language> menu

and click [OK].

Specify the scanner to be used

Select [Select Source] from the [Scan]

menu.

Install the application following the

instructions on the screen.

In the displayed dialog box, please

select [FUJITSU fi-5750Cdj] or [FUJITSU

TWAIN32], then click the [Select]

button.

When [InstallShield Wizard Complete]

screen is displayed, click [Finish].

• For Windows 98, Windows Me,

HINT

Windows 2000, Windows XP

select:

[FUJITSU fi-5750Cdj]

• For Windows 95, Windows NT 4.0:

[FUJITSU TWAIN32]

For finishing the installation, it may be

necessary to restart your computer.

Follow the instructions on the window.

ATTENTION

Select [To View] from the [scan] menu.

2-7

• Setup CD-ROM

Set the scanning resolution, document

size etc. on the [TWAIN driver] window

(for setting details of the scanning) and

click the [Scan] button.

• Confirm if the scanner is connected correctly to your

PC.

About connecting your scanner to the PC,

please refer to "2.1 Installing the

scanner" on page 2" of this manual.

HINT

Installing FUJITSU ISIS

scanner driver

Turn on the scanner.

For details about [TWAIN driver],

refer to the "FUJITSU TWAIN32

Scanner Driver User Guide" provided

on the Setup CD-ROM

HINT

Turn your PC on an log on to

Windows.

When using Windows NT 4.0, Windows

2000 and/or Windows XP, please login as

ATTENTION

The document is scanned and it’s image

will be displayed on the ScandAll 21

screen.

a user with "Administrator" privileges

(privileges of the administrator of your

PC).

If the scanning is performed successfully,

the installation has been finished.

In this manual, Windows XP screens are

used. The screens and operations might

HINT

differ slightly depending on your OS.

The scanner is automatically detected

and "A detection wizard of the new

hardware " or "An addition wizard of new

hardware" may be displayed. Please

click the [cancel] button and close the

wizard screen. (* The screen might differ

slightly depending on your OS)

For details about various types of scanning,

refer to the "fi-5750C Operator's Guide", pro-

vided on the User Manual CD-ROM.

2.3.2 For Fujitsu ISIS Scanner

Driver

Insert the Setup CD-ROM into the CD

Drive.

The <SETUP DISK STARTUP SCREEN>

will be displayed.

Preparation

Please confirm the following items before

installing the ISIS driver:

2-8

Select an appropriate language used for

the installation from the <Choose Setup

Language> window and click [OK].

This screen may not be displayed when

the, “Autoplay” setting of your PC is

turned off. In this case, please run

"Install.exe" on the CD-ROM directly from

explorer or "My Computer".

ATTENTION

Click [Install Products].

Install the application following the

instructions on the window.

When the [InstallShield Wizard Com-

pleted] appears, click on [Finish].

The system is restarted and the scan-

ner will be detected.

10.

Click [ISIS Driver].

Do not remove the Setup CD-ROM until

the PC is restarted completely.

Depending on the OS, the following

operations may be necessary.

ATTENTION

For Windows 98:

When a request for inserting the CD-

ROM of Windows 98 appears, insert

it into the CD drive and click the [OK]

button.

For Windows 2000:

When [Digital Signature not Found]

appears, click [Yes].

The Error Recovery Guide Installation

window appears.

Error Recovery Guide is a software

providing you with troubleshooting

For Windows XP:

1. When [Found New Hardware Wiz-

ard] appears, confirm that the Setup

CD-ROM is set in the CD drive, then

click the [Next] button.

2. When any alarm is displayed on

[Hardware Installation] window, click

the [Continue Anyway] button.

3. Click the [Finish] button.

information displayed on the screen when

a scanner error occurs. Not installing this

software will not have an effect on the

performance of the scanner. However it is

recommended to install this software.

When you select [Yes] for installing Error

Recovery Guide, [Choose Setup

Language] window appears. Select a

language and follow the instructions on

the window. Error Recovery Guide will

automatically start on finishing its

installation. Please wait until the

installation of ISIS driver automatically

starts.

ATTENTION

Now the installation of the scanner driver is

completed.

2-9

Install the application following the

instructions on the window.

Installing QuickScan

Pro(Trial)

"QuickScan Pro" is an imaging software that

complies with the ISIS standards. With the

FUJITSU ISIS scanner driver you can capture

scanned image data read with the scanner.

When using Windows NT 4.0, Windows

2000 and/or Windows XP, please login as

ATTENTION

a user with "Administrator" privileges

(privileges of the administrator of your

PC).

Input the requested information and

click on the [Next] button.

Insert the Setup CD-ROM into the CD

drive.

The <SETUP DISK STARTUP SCREEN>

will be displayed.

Click [Install Products].

QuickScan Pro, attached to the Setup

CD-ROM is a trial version. Therefore,

there is a limitation of 30 program starts.

Purchasing this software is necessary if

you intent to use this software unlimited.

(when installing and using the trial

version, please use the displayed serial

number. For the operations of

ATTENTION

QuickScan, please refer to the "Overview

of QuickScan" or the "QuickScan Help".

Please click [Start], [Program], and then

[QuickScan] in turn, and select then the

file to refer.

Click the [QuickScan PRO (trial)]

button in the following screen.

Install the application following the

instructions on the window.

Confirming the installation

Please confirm if the scanner operates correctly

with the following procedure.

2-10

Load the documents on the scanner.

Select [Preview Scan] from the [Scan]

menu to start the scanning-

For loading documents, please refer to

Chapter 2 "BASIC SCANNER

OPERATIONS" of the "fi-5750C Operator's

Guide".

If the scanning is completed without any

troubles, the installation was performed

successfully.

Start QuickScan Pro.

Please select [Start], [Programs],

[QuickScan] in turn, then click on

[QuickScan].

Select [Scan], and [Select

Scanner...] from the menu bar.

Select Fujitsu fi-5750C, then click the [OK]

button.

Refer to "QuickScan Overview" or

"QuickScan Help" for information

about QuickScan functions and oper

HINT

ations. On the [Start] menu, point to

[Programs] - [QuickScan] and click

the file.

Select [Preview Setting...] from the

[Scan] menu. Set the reading

resolution and document size, then

click [OK].

2.3.3 Installing other application

programs

Installing Error Recovery

Guide

If you did not install the Error recovery guide

together with the driver, please follow the

below given procedure for installing it

separately.

When Error Recovery Guide is installed on

your PC, it displays troubleshooting informa-

tion on screen if any scanner error occurred.

Insert the Setup CD-ROM in your CD

drive.

The <SETUP DISK STARTUP SCREEN>

will be displayed.

2-11

Click [Install Products].

When the [InstallShield Wizard

Complete] screen is displayed, click

[Finish].

Click [Error Recovery Guide] in the fol-

lowing screen.

Installing the Image

processing software option

(trial version)

For the installation of the image processing

software option (trial version), please refer to

the "Image Processing Software Option User's

Guide".

Installing Adobe Acrobat

Install Adobe Acrobat from the "Adobe Acro-

bat 6.0 CD-ROM" provided with this scanner.

Select a language to use for the installa-

tion in the <Choose Setup Language>

window and click [OK].

Adobe Acrobat 6.0 Standard is not

supported by Microsoft Windows 95,

ATTENTION

Microsoft Windows NT4.0, Microsoft

Windows 98, Microsoft Windows Me.

(Except for Microsoft Windows 98

Second Edition.)

To use Acrobat 6.0 with FUJITSU

scanners, FUJITSU TWAIN32 Scanner

Driver Version 8.11.32 or later, or Version

9.11.32 or later is required.

Install the application following the

instructions on the window.

Adobe Acrobat is required for displaying

the manuals stored on the CD-ROM.

HINT

* The installation of Adobe Acrobat 6.0 is

not necessary if it is already installed on

your PC.

Insert the Adobe Acrobat 6.0 CD-ROM

into your CD-ROM drive.

The CD-ROM is automatically

recognized and the "Adobe Acrobat6.0

AutoPlay" screen will be displayed.

2-12

The <Adobe Acrobat 6.0 AutoPlay>

screen may not appear when the

“Autoplay” setting of your PC is turned off.

In this case, run" AutoPlay.exe" on the

CD-ROM directly from the explorer or

"My Computer".

Support and User registration for

Adobe products

ATTENTION

For details, refer to the technical support

information stored in the [Customer

Support] folder on Adobe Acrobat 6.0

Standard CD-ROM. (Note that free

person-to-person support is not available

for this is bundled product.)

Click the [Install] button when the

following screen is displayed. Then

click the [Install Acrobat 6.0 Standard]

button.

Click the [Next] button when the

following screen is displayed.

The installation is started and its setup

screen is displayed.

After the setup screen is displayed, fol-

low the instructions on the screen to

perform the installing.

For more detailed information about the

Adobe Acrobat 6.0 installation, please

read "Read me" displayed at the screen

of operation 2. For the operations of

Adobe Acrobat 6.0, please refer to the

"Adobe Acrobat 6.0 help".

HINT

2-13

2-14

Appendix

Appendix 1 T r oubleshooting .......................... AP-2

Appendix 2 Daily Care ................................... AP-6

Appendix 3 Replacing Consumables ............ AP-8

Appendix 4 Setting the position of the ADF ... AP-9

AP-1

Appendix 1 Troubleshooting

Before you ask for repair service, check the following items. If the problem persists even after implementing

remedies below, contact the dealer where your purchased the or an authorized FUJITSU service provider.

Troubleshooting checklist

TABLE 1.

Symptom

Check this Item

Remedy

Scanner cannot be

tuned ON.

Did you push the power switch?

Is AC cable connected correctly?

Push the power switch.

Correctly connect the AC cable.

Disconnect the AC cable from the scanner,

then connect it again. If this does not restore

the power supply, contact the dealer where you

purchased the scanner or an authorized

FUJITSU scanner service provider.

Is Windows normally started up?

Is the shipping lock unlocked?

Push the power switch again after completely

starting up Windows.

Unlock the shipping lock.

Scanning does not start. Are the documents loaded

correctly on the ADF paper chute?

Load the document correctly on ADF paper chute.

Is the ADF closed completely?

Close the ADF completely.

Is USB or SCSI cable connected

correctly?

Correctly connect the cable. (When a USB hub is

used, check the hub’s power supply.)

Is the SCSI ID set correctly?

(When using SCSI interface)

Set the SCSI ID correctly using SCSI ID switch on

the rear of the scanner.

Does the Function No. display

indicates an alarm or an error?

When the Function No. display indicates an alarm

or an error, refer to "6 TROUBLE SHOOTING" in

the "fi-5750C Operator's Guide".

Does the alarm state remain

displayed even after the scanner

has been turned OFF and back ON

again?

Turn OFF and ON the scanner.

If this does not eliminate the alarm state, contact

the dealer where you purchased the scanner or an

authorized FUJITSU service provider.

Vertical lines appear in

the printed images.

(When using the Flatbed)

Are the glass and document

holding pad dirty?

Clean the glass and document holding pad

following the instructions in "4.3 Cleaning

Flatbed" of the "fi-5750C Operator's Guide".

(When using the ADF)

Is the glass inside the ADF dirty?

Clean the glass following the instruction in “4.2

Cleaning ADF” of the “fi-5750C Operator’s

Guide”.

The printed scanned

image shifts or is dis-

torted.

(When using the Flatbed)

Are the glass and document

holding pad dirty?

Clean the glass and document holding pad

following the instructions in "4.3 Cleaning

Flatbed" of the "fi-5750C Operator's Guide".

(When using the Flatbed)

Is the document holding pad

dirty?

Install the document holding pad correctly.

(When using the ADF)

Do not press down the ADF nor place heavy

Is the ADF cover pressed down or objects on the ADF during scanning.

heavy object placed on the ADF

during scanning?

(When using the ADF)

Is something causing the scanner

to vibrate during scanning?

Do not allow anything to cause the scanner to

vibrate while scanning.

AP-2

TABLE 1.

Symptom

Check this Item

Remedy

The printed scanned

image shifts or is dis-

torted.

Are the documents loaded

correctly?

Load the documents correctly.

Quality of scanned

images is unsatisfac-

tory.

(When using the Flatbed)

Is the document holding pad

dirty?

Install the document holding pad correctly.

(When using the ADF)

Is the glass inside the ADF dirty?

Clean the glass following the instruction in “4.2

Cleaning ADF” of the “fi-5750C Operator’s

Guide”.

Double feeds occur fre- Do the documents qualify the

Use the documents that qualify the "Document

quently.

"Document Quality" and "Double- Quality" and "Double-feed Detection Condition"

feed Detection Condition" in "8

DOCUMENT SPECIFICATON

FOR THE ADF" of the "fi-5750C

Operator's Guide" fi-5750C?

in "8 DOCUMENT SPECIFICATON FOR THE

ADF" of the "fi-5750C Operator's Guide".

Are the documents set properly on Fan the documents before scanning. Correctly

the ADF paper chute?

align the document stack and load them on the

ADF paper chute. For details, refer to "2 BASIC

SCANNER OPERATIONS" of the "fi-5750C

Operator's Guide".

Is the document stack thicker

than: 20mm? (for A4 size paper)

10mm? (for A3 size paper)

Reduce the number of sheets in the document

stack to 20mm (for A4 size paper) or 10mm (for

A3 size paper) thickness or less.

Is the Brake roller dirty?

Clean the Brake roller. For details, refer to "4

DAILY CARE OF THE EQUIPMENT" of the "fi-

5750C Operator's Guide"

Is the Brake roller worn out?

Do the documents qualify the

Replace the Brake roller. For details, refer to "5

REPLACING CONSUMABLES" of the "fi-

5750C Operator's Guide"

Documents are not fed

into the ADF (pick

error occurs frequently

or the document stops

midway).

Use the documents that qualify the "Document

"Document Quality" and "Double- Quality" and "Double-feed Detection Condition"

feed Detection Condition" in "8

DOCUMENT SPECIFICATON

FOR THE ADF" of the "fi-5750C

Operator's Guide"?

in "8 DOCUMENT SPECIFICATON FOR THE

ADF" of the "fi-5750C Operator's Guide".

Is the Pick roller set dirty?

Clean the Pick roller set. For details, refer to 4.2

"Cleaning the ADF" of the "fi-5750C Operator's

Guide".

Is the Pick roller set worn?

Replace the Pick roller set. For details, refer to 5.3

"Replacing the pick roller set" of the "fi-5750C

Operator's Guide".

Is there any debris on the

document feed path?

Remove any debris from the document feed path.

The scanned images are Are the Feed rollers dirty?

elongated.

Clean the Feed rollers. For details, refer to the "fi-

5750C Operator's Guide".

Did you adjust the scan scale?

For Windows 98, Windows Me, Windows 2000

and Windows XP, please select [Scanner and

Camera] in the [Control Panel], then click [Device

Set] tab to adjust the scan scale.

For Windows 95 and Windows NT 4.0, right-click

Scanner Control Center icon in task tray, select

[Option] and adjust the scan scale. Please refer to

“7 Online Setup” of the “fi-5750 Operator's

Guide” and adjust the offset from the Software

Operation Panel (online settings).

AP-3

TABLE 1.

Symptom

Check this Item

Remedy

There is a shadow on

the leading edge of the

scanned images.

Are the Feed rollers dirty?

Clean the Feed roller. For details, refer to "4

DAILY CARE OF THE EQUIPMENT" of the "fi-

5750C Operator's Guide"

Adjust the offset.

For Windows 98, Windows Me, Windows 2000

and Windows XP, adjust the [Sub-scan Setting\

on] Scanners and Cameras\ in the [Control Panel].

For Windows 95 and Windows NT 4.0, right-click

the Scanner Control Center icon, select [Options] -

[Sub-scan Setting] and adjust the offset. Please

refer to Chapter 7 “Online Setup” of the “fi-5750

Operator's Guide” and adjust the offset from the

Software Operation Panel (online settings).

AP-4

TABLE 3.

Temporary Error

Indication

Meaning

TABLE 2.

Flatbed motor malfunction.

Optical error (Flatbed).

Optical error (ADF front).

Optical error (ADF back).

Motor fuse malfunction.

Lamp fuse malfunction.

Operator panel malfunction.

EEPROM malfunction.

Indication

Meaning

Confirm that the shipping lock

is released.

A paper feed error occurred.

A double feed error occurred.

The ADF cover is opened.

The following shows the procedure for resolv-

ing of each temporary error.

SCSI interface fuse

malfunction.

Image memory malfunction.

Memory malfunction.

• "U0" error

Release the shipping lock.

For releasing the shipping lock, refer to 2.1

“Installing the Scanner” in this manual.

Malfunction at SCSI interface

controller.

Background switching

malfunction.

• "U1" error

Remove jammed documents.

Confirm that the documents meet the paper

conditions for scanning.

Refer to Chapter 6 "TROUBLE SHOOTING" in the

"fi-5750C Operator's Guide".

E10

E11

E12

E15

ROM malfunction.

Fan malfunction.

Heater malfunction.

Malfunction in the additional

memory option.

• "U2 " error

E16

E18

E19

E1A

Option board malfunction.

Sensor malfunction.

LSI malfunction.

Remove jammed documents

Confirm that the documents meet the paper

conditions for scanning.

Refer to "8 DOCUMENT SPECIFICATION OF

ADF" of the "fi-5750C Operator's Guide".

Internal communication

malfunction.

• "U4" error

Close the ADF cover completely.

For details, refer to “6 TROUBLESHOOTING” in

the “fi-5750C Operator’s Guide”.

About Error Recovery Guide

HINT

When this software is installed on your

PC, the icon appears in the task tray

when Windows is started up. If any

device alarm or temporary error

occurred, the Error Recovery Guide win-

dow appears and displays information

such as error names and error codes

regarding the alarm. Record the informa-

tion and click [Details...] to know more

detailed information for trouble shooting.

Device alarm (Permanent

error)

When you encounter any alarm, turn OFF and

ON the scanner. If the alarm is still displayed

on the Function No. display, contact the dealer

where you purchased the scanner or an

authorized FUJITSU scanner service provider.

AP-5

Appendix 2 Daily Care

The glass of the inside of the ADF becomes hot during operation.

CAUTION

When you clean the inside of the scanner, turn OFF the power and unplug the AC cable from

the outlet and wait for at least three minutes.

Do not turn OFF the scanner when you clean the Feed rollers and Plastic Rollers.

Cleaning Materials

TABLE 4.

Cleaning Materials

Parts No.

Remarks

Cleaner F1

CA99501-0013

1 bottle.

Moisten a cloth with this fluid

and wipe the respective areas. *1

Cleaner F2

CA99501-0014

CA99501-0012

1 bottle.

Moisten a cotton swab with this

fluid and clean the respective

areas. *1

Cleaning Paper

10 sheets / package. Moisten a

Cleaning Paper with Cleaner F1

and insert it into the ADF. *1

Lint-free dry cloth

Commercially available one.

*1) For details on the cleaning materials, contact the FUJITSU scanner dealer where you purchased the scanner.

Do not clean the rubber rollers with Cleaner F2.

CAUTION

AP-6

Locations and Cycle for Cleaning

TABLE 5.

Standard Cleaning

Cycle using Cleaner

Standard Cleaning

Cycle using Cleaning

Paper with Cleaner F1 F2

Standard Cleaning

Cycle using Cleaner

Part to Clean

Clean these parts

after every 10,000

scans.

Clean these parts

after every 10,000

scans.

Clean these parts

when dirty.

Flat Bed Document Holding Pad

Document Bed

ADF

Chute Roller

Pick Arm

Pick Roller Set

Brake Roller

Feed Rollers

Plastic Rollers

Sheet Guide

Glass

Ultra Sonic Sensor

Clean this part with a dry lint-free dry cloth.

For details on the cleaning the ADF, refer to Chapter 4 "DAILY CARE OF THE EQUIPMENT" of

the "fi-5750C Operator Guide".

The scanner must be cleaned more frequently if you scan any of the following type of documents.

ATTENTION

• Documents of coated paper.

• Documents that are almost completely covered with printed text or graphics.

• Chemically treated documents such as carbonless paper

• Documents containing a large amount of calcium carbonate

• Handwritten documents

AP-7

of the used paper and how frequently the

scanner is used and cleaned.

Appendix 3 Replacing

Consumables

Use only the specified consumables.

ATTENTION

Do not use other consumables.

The glass of the inside of the

ADF becomes hot during opera-

tion.

CAUTION

The following pictures shows the locations of

the parts to be replaced. Refer to "Chapter 4

Replacing Consumables" fi-5750C Operator's

Guide on User Manual CD-ROM.

When you clean the inside of

the scanner, turn OFF the power

and unplug the AC cable from

the outlet and wait for at least

three minutes.

Pick Roller Set

Consumables and

Replacement Cycle

The following table shows the specifications

of consumables and guidelines for the

replacement cycle.

TABLE 6.

Standard

Replacement

Cycle

Description

Part No.

Brake Roller

PA03338-K010 After 250,000

scans or one

year.

Brake Roller

Pick Roller*

PA03338-K011 After 250,000

scans or one

year.

* A set of two rollers.

For purchase of consumables, contact the store

where you purchased the scanner or an autho-

rized FUJITSU scanner service provider.

The replacement cycles above are rough

guidelines for the case of using A4/Letter

woodfree or wood containing paper 64 g/m2

(17 lb). This cycle varies according to the type

AP-8

- For left-handed operators

Appendix 4 Setting the

position of the

ADF

As the factory default, ADF of fi-5750C is

fixed with ADF lock screws. Be sure to remove

the screws before changing the position of the

ADF.

ADF can be set to the following three posi-

tions:

• Type 1: Traditional

-Traditional style of previous FUJITSU scanner

products

-For operators accustomed to previous FUJITSU

scanners

Type 2 and 3 are available only when the ADF

is set to the center position. Before changing

the ADF position to Type 2 or 3, slide the ADF

to the center position. When the ADF is in

Type 2 position, you can change the position to

Type 3 by rotating the ADF in 180 degrees and

vice versa.

• Type 2: Standard

- Small foot print

- For right-handed operators

For details on setting the ADF, refer to 2.2

“Setting the ADF” of “fi-5750C Operator’s

Guide” on Manual CD-ROM.

Take care not to pinch your

fingers when rotating the ADF.

CAUTION

• Please rotate the ADF after you set

ATTENTION

the stacker upright.

• Type 3: Reversed

• When you change the position of

the ADF, do not rotate it over 180

degrees, other wise the ADF may

be damaged.

- Small foot print

AP-9

fi-5750C Image Scanner Getting Started

P3PC-E737-02EN

Date of issuance: June, 2006

Issuance responsibility: PFU LIMITED

Printed in Singapore

zCopying of the contents of this manual in whole or in part and copying of the scanner

application is forbidden under the copyright law.

zThe contents of this manual are subject to change without notice.

zPFU LIMITED is not liable whatsoever for any damages resulting from use of this scan-

ner and procedures described in this manual, profit loss due to defects, and any claims

by a third party.

Therma Stor Products Group Ts 261b User Manual
Sony Mx C400p User Manual
Oricom Secure 100 User Manual
MAKITA GA012G User Manual
LG 75XS4G User Manual
KENWOOD HB650 02 User Manual
JVC DX J36UX User Manual
EMERSON FISHER 6351 User Manual
BROTHER EM 550 User Manual
ASUS X550C User Manual