Home Cinema 3200/3800 Series
Remove the lens cap.
3
4
Quick Setup
IMPORTANT: Before using this product, make sure you read these instructions
and the safety instructions in the online User’s Guide.
Note: These illustrations show the Home Cinema 3800, but the instructions are
the same for the Home Cinema 3200 unless otherwise noted.
Press the
power button on the projector or the On button on the
Connect the projector
remote control. The power light flashes blue, then stays on.
Connect two video devices or computers simultaneously with a commercially
available HDMI cable. Use the Source buttons on the remote control or the
Home and arrow buttons on the projector to switch between them.
HDMI cable
Note: To shut down the projector, press the
power button on the
projector or the
Standby button on the remote control, then press the
Note: The DC Out (2.0A) port provides power to streaming media devices.
button again to confirm, if necessary. Wait for the projector to cool down
before unplugging it.
For more details and additional connection types, see the online User’s Guide.
Use the arrow buttons on the projector or remote control to highlight any
of the options that appear on the Home screen, then press Enter to select
it. You can switch between projection sources and quickly access various
adjustment options from this screen.
5
Connect audio
External speakers
You can connect the projector to external self-powered speakers through the
Audio Out port.
Note: If you connect external speakers to the Home Cinema 3800, the
projector’s internal speakers are muted.
3.5 mm stereo mini cable
The default language of the menu system is English. To select another
language, press the Menu button on the projector or remote control.
Select Extended and press Enter. Select Language and press Enter.
Select your language and press Enter. Press the Menu button to exit the
menu system.
6
Bluetooth® devices
You can pair a Bluetooth device to the projector to output audio from a
device connected to one of the HDMI ports. See the online User’s Guide for
instructions.
Adjust the image
If you don’t see an image, press one of the Source buttons on the remote
control or the Home and arrow buttons on the projector to select the
1
image source.
Note: If you still see a blank screen or have other display problems,
see the troubleshooting tips on the back of this sheet.
For the best image quality, place the projector directly in front of the
2
center of the screen, facing the screen squarely. If this is not possible, turn
the horizontal and vertical lens shift dials to adjust the image position and
center it on the screen.
Turn on your equipment
Turn on your video source or computer.
1
Plug in the projector.
2
If the image is tilted, adjust the front feet as shown below.
3
4
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Turn the zoom ring to reduce or enlarge the image.
Turn projector off
Turn projector on
Display Home screen
Choose which source
to display
Temporarily mute audio
and video
Display a test pattern
for image focusing
Control connected
sources with HDMI Link
Mute audio
Turn the focus ring to sharpen the image.
5
6
Adjust volume
Display HDMI Link menu
Change the color mode
Display Dynamic Range
menu
Navigate projector
menus
Access projector menus
If your image is uneven on the sides, you can use the keystone correction
feature to adjust the image. To use this feature, you must first set the lens
to the center-top position using the lens shift dials.
For more information on using the remote control, see the online
User’s Guide.
Viewing 3D images
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector. You will also need a pair of Epson®
(part number V12H548006) or Epson-compatible RF 3D active shutter glasses.
Press the
correction screen. Press the
or button (Home Cinema 3800) to correct for horizontal keystone
or
button on the projector to display the keystone
or button (Home Cinema 3200), or the
distortion. Press the
distortion.
or
button to correct for vertical keystone
Turn on and begin playback on the 3D-compatible video device.
1
Note: Make sure you set the video device to play content in 3D mode.
Home Cinema 3200
Press the 3D Format button on the remote control, if necessary.
2
Slide the power switch on your 3D glasses to the On position.
3
Home Cinema 3800
Note: If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
See the online User’s Guide for more information on adjusting 3D images.
Registration
Register today to get product updates and exclusive offers. You can register
Troubleshooting
If you see a No signal message after turning on the projector, make sure
•
your video device or computer is properly connected.
If you see a blank screen, check the following:
•
Optional accessories
Make sure the
flashing.
power light on the projector is blue and not
•
•
•
For a list of optional accessories, see the online User’s Guide.
You can purchase RF 3D glasses (part number V12H548006) or other
accessories from an Epson authorized reseller. To find the nearest reseller,
call 800-GO-EPSON (800-463-7766). Or you can purchase online at
Press the
power button to wake the projector from standby or
sleep mode, if necessary.
Press one of the Source buttons on the remote control or the
Home and arrow buttons on the projector to switch to the correct
image source, if necessary.
Notices
Bluetooth Safety and Specifications
If you see a blank screen when a computer is connected, check the
following:
•
On some Windows® laptops, you may need to hold down the Fn
key and press F7 or the function key that lets you display on an
external monitor. It may be labeled CRT/LCD or have an icon such
Contains Bluetooth module model: DBUB-E207
•
This document provides safety instructions and describes the specifications. Read this
document carefully before use to ensure your safety and product performance. Data
transmission is always initiated by software, which is then passed down through the
MAC, through the digital and analog baseband, and finally to the RF chip. Several
special packets are initiated by the MAC. These are the only ways the digital baseband
portion will turn on the RF transmitter, which it then turns off at the end of the packet.
Therefore, the transmitter will be on only while one of the aforementioned packets is
being transmitted. In other words, this device automatically discontinues transmission in
case of either absence of information to transmit or operational failure.
as
.
On Windows 7 or later, hold down the Windows key and press P at
the same time, then click Duplicate.
If you’re using a Mac laptop, open System Preferences and
select Displays. Click the Arrangement tab and select the Mirror
Displays checkbox.
•
This equipment is restricted to indoor operation only.
U.S.
Contains FCC ID: BKMAE-E207
If the keystone correction feature doesn’t correct the image, make sure
you first set the lens to the center-top position using the horizontal and
vertical lens shift dials.
•
•
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
If 3D images aren’t displaying properly, check the following:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
Press the Menu button on the projector or remote control, select
•
the Signal menu, then 3D Setup, then select 3D Display. Make
sure that the 3D option is selected. You may also need to set the
Diagonal Screen Size setting in the Signal menu. See the online
User’s Guide for more information.
Make sure to wear the 3D glasses within 32 feet (10 m) of the
projector.
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
•
Check that your 3D glasses have not entered standby mode. Slide
the power switch on the 3D glasses into the Off position, then
back to the On position.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
Check that your video device and media are both 3D-compatible.
Refer to the documentation that came with your video device for
more information.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment. Properly shielded
and grounded cables and connectors must be used for connection to host computers
and / or peripherals in order to meet FCC emission limits.
•
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
If the projector does not respond to remote control commands, make
sure the batteries in the remote control are installed correctly. Replace
the batteries, if necessary.
•
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
This equipment should be installed and operated keeping the radiator at least 7.8
inches (20 cm) or more away from person’s body.
Where to get help
Manual
Canada
Contains IC: 1052D-E207
CAN ICES-3(B)/NMB-3(B)
For more information about using the projector, you can view or download
This device complies with Industry Canada license-exempt RSSs. Operation is subject to
the following two conditions: (1) This device may not cause interference; and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
the online manual from the Epson website, as described below.
Internet support
and search for your product to download software and utilities, view the
manual, get FAQs and troubleshooting advice, or contact Epson.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment should be installed and operated keeping the radiator at least 7.8 inches (20
cm) or more away from person’s body.
Telephone support services
To use the Epson PrivateLine® Support service, call (800) 637-7661. This service
is available for the duration of your warranty period. You may also speak with
a support specialist by calling (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and
7 am to 4 pm, Pacific Time, Saturday. Days and hours of support are subject
to change without notice. Toll or long distance charges may apply.
EPSON is a registered trademark and EPSON Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PrivateLine is a registered trademark of Epson America, Inc.
Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.
Mac is a trademark of Apple Inc., registered in the U.S. and other countries.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2019 Epson America, Inc., 6/19
Printed in XXXXXX
CPD-57545
|