Quick Start Manual
MANUAL-WING (NC)
For latest version visit:
•
•
Status Led indicating if the device is powered up and
running. Blinks at 1Hz in normal mode, blinks at 5Hz
when
Activity Led indicates the network capacity. (ON to
indicate 100Mb connection, and OFF to indicate
10Mb connection)
Link led indicating the presence of an Ethernet
connection.
7V DC power connector
Box Contents
•
•
•
•
•
•
ENTTEC Wing (70031, 70032 or 70033)
7V Power supply (79111)
Country specific plug for power supply
Cat5 patch cable (79102)
Default IP address Label
This user manual
•
•
Shortcut Wing Features
Note: The user manual for all ENTTEC Wings is the same.
Please refer to the section relating to that specific product.
•
•
•
•
•
Ethernet Interface
60 High quality Cherry MX Keys
2 Digit 7 Segment LED display
PAGE UP & PAGE DOWN Keys
Upgradeable firmware (using web-interface)
Introduction
ENTTEC Playback Wing supports two modes, and only one
mode can be active at a single time:
•
ENTTEC Mode: Default mode, and is supported by
software such as D-PRO and Lightfactory.
Art-Net Mode: Each key can be mapped to an Art-
Net channel and used as required.
Playback Wing Features
•
•
•
•
•
•
•
•
Ethernet Interface
40 High quality Cherry MX Keys
10 High Quality 60mm Faders
2 Digit 7 Segment LED display
PAGE UP & PAGE DOWN Keys
Large GO & BACK Keys
ENTTEC Shortcut and Program wings only support
ENTTEC Mode.
Other software programs might support ENTTEC wings,
and their operation as it relates to those software titles will
be explained in full by those vendors.
After, un-packing the unit from the box, on the rear panel,
you will find:
Upgradeable firmware (using web-interface)
•
RJ45 Ethercon connector for a 10/100Mb
connection
Program Wing Features
•
Ethernet Interface
1
ID: 210583
Quick Start Manual
MANUAL-WING (NC)
For latest version visit:
When the update is complete, the page will refresh and
you will be taken to the home page – where you can verify
the firmware version.
Since, ENTTEC Wing will reboot after a firmware update,
please allow a few seconds for it to be refreshed in the
browser. Please wait until the update process is complete.
NMU
NMU (Node Management Utility) is a free Windows and
Mac application that is used to manage compatible
ENTTEC nodes over Ethernet.
1. Download NMU from: enttec.com/nmu
To update the firmware on the Wing, please use “Update
Firmware” page, and follow the steps given below.
2. Ensure that your ENTTEC Wing is hooked up physically by
Ethernet cable, to your network.
Firmware Update
3. Open NMU. If prompted with multiple networks, select the
correct network. (Identified by the IP address of your com-
puter on the network, to which the Wing is connected.)
From this page you can update the latest firmware of the
ENTTEC Wing (firmware
file
is
available at
firmware file.
Choose or browse the firmware file (as per your browser)
and click on Update firmware to start the process.
4. Press the Discovery button, and wait till NMU finds all sup-
ported ENTTEC devices on your network. Select the Wing and
click Configure.
The update progress is shown in real-time, and will take a
few seconds for the update to complete.
3
ID: 210583
Quick Start Manual
MANUAL-WING (NC)
For latest version visit:
ENTTEC Wings are supported by various software titles. Please
refer to the respective software user-manual or online guide
for more details on what functions are supported, and
how to setup the Wings:
Art-Net Mode: Playback Wing
•
•
•
•
D-PRO User Manual
LightFactory User Guide
FreeStyler
QLC+
Wing Specifications
You will need to select the Subnet and Universe from the
appropriate pulldowns in the Art-Net mode, which will tell
the Wing which Art-Net universe of the 255 possible
choices to use for the information it generates.
Due to continuous improvements and innovations of all
ENTTEC products, specifications and features are subject to
change without notice.
Item
Value
7-9V DC
You can assign a total of 50 addresses to the 10 sliders and
the 40 buttons. The buttons have the option to be set for
Toggle or Flash, for each button.
Power Requirements
Weight
6.6 lbs / 3.0 Kg
13.4” / 340mm
9.45” / 240mm
1.26” / 32mm
AUTOFILL: The Auto Fill button will return the assignments
to the default configuration, shown above.
Length
Width
SET CONFIG TO WING: Saves the changed configuration
to the Wing.
Height
PAGE UP/DN: In addition to the 50 you have selected on
the main screen, you have access to up to 450 other DMX
addresses in the same Art- Net universe by pressing Page
Up and Page Down buttons on the Wing.
Op Environment
Connectors
0°-50°C
1x RJ45 Ethercon connector
In the example shown above, on Page 2, the sliders would
correspond to channels 51-60.
Ordering Information
The ENTTEC Wings and compatible products can be ordered
from our website or through your ENTTEC dealer.
EXCEEDING CHANNEL 512: Starting at higher than 62,
you may run out of room on page 10 or even before. Such
an arrangement would simply mean that on that page the
button or slider does nothing.
PN
Description
70031
Shortcut Wing
70032
70033
Playback Wing
Program Wing
Supported Software
4
ID: 210583
Quick Start Manual
MANUAL-WING (NC)
For latest version visit:
70573
70043
D-PRO 2U
Wing Rackmount Kit
5
ID: 210583
|