TM
®
Chipper/Shredder with 2-Way Feed
Owner’s Manual
This manual contains important safety instructions for
Chipper/Shredder models: CH3, CH4, CH9
READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS
CAREFULLY SAVE THESE INSTRUCTIONS.
For product questions or service,
CALL 1-919-550-3221
When you call the help-line you will need to have the following information:
Date of Purchase:
_______________________
Location of Purchase: _______________________
Serial #:
Model #:
_______________________
_______________________
Heavy Duty Power Equipment
Contents
Warnings ............................................................................ 1
Product Specifications........................................................ 2
Component Identification ................................................... 3
Missing Parts Order Form…………………………………….4
Safety Information.............................................................. 5
Operating Guidelines ......................................................... 6
Assembly............................................................................ 7
Important Engine Information............................................. 8
Operating Instructions........................................................ 9
Maintenance & Storage.................................................... 10
Troubleshooting ............................................................... 12
Limited Warranty & Service.............................................. 13
Rev: 05/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
Heavy Duty Power Equipment
Warnings
This symbol indicates important safety instructions
which, if not followed, could endanger personal safety
and/or property. Read and follow all instructions in this
manual before attempting to operate this machine.
Failure to comply with these instructions may result in
personal injury. When you see this symbol—heed its
warning.
Keep bystanders, helpers, pets, and children at least 75
feet from the machine while it is in operation. Stop
machine if anyone enters the area.
Wear hearing and eye protection while operating this
machine or if you are within 75 feet of this machine.
Thrown objects which ricochet can cause serious injury to
the eyes.
CARBON MONOXIDE GAS
Exhaust contains poisonous carbon monoxide, a colorless
and odorless gas. Breathing exhaust can cause loss of
consciousness and may lead to death.
The Engine Exhaust from this product contains chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm.
Never wear loose clothes or long jewelry and keep your
long hair under a headgear when operating machine.
Never operate this machine in bare feet or sandals.
Never use machine on a slope or hard smooth floor.
This machine has a rotating cutting blade capable of
amputating hands and feet and throwing objects. Keep
hands and feet out of openings while machine is running.
Failure to observe these safety instructions could result in
serious injury or death.
Gasoline is extremely flammable and the vapors are
explosive. Serious personal injury can occur when
gasoline is spilled on you or your clothing, which can
ignite. In the event of a gasoline spill, wash your skin and
change clothes immediately.
WARNING: Do not deposit branches larger than 3” x 4”
inches in diameter (depending on Model #, see Model
Specifications table pg 2) in the side chute. Do not
deposit branches larger than 1/4 inches into the funnel.
WARNING: Do not operate this machine unless the chute
deflector has been installed properly.
DO NOT force the branches into this machine, allow the
machine to automatically feed through.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
1
Warnings
Heavy Duty Power Equipment
Training
1. Read, understand, and follow all instructions on the
machine and in the manual) before attempting to
assemble and operate. Keep this manual in a safe
place for future and regular reference and for
ordering replacement parts.
7. Do not put hands or feet near rotating parts or in the
feeding chambers and discharge opening. Contact
with the rotating impeller can amputate fingers,
hands, and feet.
8. Never attempt to unclog either the feed intake or
discharge opening, remove or empty bag, or inspect
and repair the machine while the engine is running.
Shut the engine off and wait until all moving parts
have come to a complete stop. Disconnect the spark
plug wire and ground it against the engine.
2. Be familiar with all controls and their proper
operation. Know how to stop the machine and
disengage them quickly.
3. Never allow children under 18 years old to operate
this machine. Children 18 years old and over should
read and understand the operation instructions and
safety rules in this manual and should be trained and
supervised by a parent.
NOTE:
The operator or
user is
4. Never allow adults to operate this machine without
proper instruction.
responsible for
accidents or
hazards
5. Keep bystanders, helpers, pets, and children at least
75 feet from the machine while it is in operation. Stop
machine if anyone enters the area.
occurring to other
people, their
property, and
themselves.
6. Never run an engine indoors or in a poorly ventilated
area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
Product Specifications
Chipper/Shredder Model # Specifications
Model #
CH3
CH4
CH9
Maximum RPM
3600 RPM
3600 RPM
3600 RPM
Horsepower
11 HP
Recoil
15 HP
Recoil
15 HP
Recoil and Electric
Starter
Starting System
Emission Compliance
Fuel Capacity (gal.)
Engine Type
49 States
1.4 gal.
DEK
49 States
1.4 gal.
DEK
49 States
1.4 gal.
DEK
Displacement (cc)
Walk or Pull
279 cc
either
Yes
420 cc
either
Yes
420 cc
either
Yes
Chipper
Shredder
Yes
Yes
Yes
Maximum Cutting
Thickness Diameter (in.)
3” x 3”
3” x 4”
3” x 4”
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
2
Heavy Duty Power Equipment
Component Identification
Red Electric Start Push
Button
Chipper Funnel
Use the chipper funnel to
feed leaves only.
Fuel Tank
Use regular unleaded fuel. Always
leave about 1” of air gap at the top of
the tank for fuel expansion to prevent
seepage or spills.
120V Outdoor Extension
Cord Connection (Plug
in for 120V electric start)
Choke Lever
Move the choke lever to the
CHOKE position to prepare a
cold engine for starting.
On/Off Switch
Set this switch to On before
using recoil starter. Set switch
to Off to switch off engine.
Recoil Starter
The starter handle is located on
the engine. Pull the starter
handle to start engine.
Fuel Valve
Use the fuel valve to turn
fuel on and off to engine.
Blade Access Hatch
Remove the blade access
hatch to clean, remove, or
sharpen the chipper/shredder
blade.
Serial #:
Stamped on engine block
between funnel and engine
Chipper Chute
Use the chipper chute to feed
longer and/or thicker pieces of yard
waste into the impeller for
chipping. Depending on the model
#, the chipper/shredder can cut up
to a 3” x 4” in diameter piece of
wood.
Discharge Chute
Chipped materials are
discharged through this
opening. It may be left open or
the chipper collection bag can
be attached to the chute.
Hardware Bag
Lawn Tractor or ATV Hitch
Use this hitch to tow the chipper/shredder behind a lawn
tractor or ATV (maximum tow speed is 15 mph).
This bag contains the assembly hardware, safety devices
and chipper collection bag. Use the chipper bag to collect
shredded or chipped material fed through the chipper chute
or hopper assembly.
If you are missing any parts, please complete the form on the next page and fax it back to us at: 919-550-3277.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
3
Heavy Duty Power Equipment
Missing Parts Request Form
Please indicate the part that you are missing:
Hardware bag
Wheel Kit
Other
Name
Address
Date of purchase
Model #:
CH3
CH4
CH9
Phone
Email
Serial #:
Comments:
IMPORTANT: Please include your receipt. Without a receipt, your
order will be delayed. You may also email us at:
[email protected]. If emailing, please scan in
your proof of purchase.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
4
Safety Information
Heavy Duty Power Equipment
Your Responsibility
Restrict the use of this chipper/shredder to persons who read, understand and follow the warnings
and instructions in this manual and on the machine.
Note: Not all safety labels shown may apply to your chipper/shredder.
i. Never store machine or fuel container inside near
Preparation
an open flame, spark, or pilot light (e.g., furnace,
water heater, space heater, clothes dryer, etc.).
1. Thoroughly inspect the area where the chipper/
shredder is to be used. Remove all rocks, bottles,
cans, or other foreign objects which could be picked up
or thrown and cause personal injury or damage to the
machine.
j. To reduce the fire hazard, keep machine free of
grass, leaves, or other debris build-up. Clean up
oil or fuel spills and remove any fuel soaked
debris.
k. Allow machine to cool at least 5 minutes before
storing.
2. Avoid discharging chipped material out of the
discharge chute against a wall or on asphalt, concrete,
or other hard surfaces as material being ejected could
ricochet, causing injury to you or bystanders.
8. Never attempt to make any adjustments while the
engine (motor) is running (except where specifically
recommended by the manufacturer).
3. Always wear safety glasses or safety goggles to
protect eyes during operation or while performing an
adjustment or repair.
Safety Label Locations
These labels warn you of potential hazards that can
cause serious injury. Read them carefully. If a label
comes off or becomes hard to read, contact your GXi
Outdoor Power dealer for a replacement.
4. Wear sturdy, rough-soled work shoes and closefitting
pants and shirts. Loose fitting clothing or jewelry can
be caught in movable parts. Wear leather work gloves
when feeding material in the chipper chute.
Safety Information
5. Before starting the engine, check bolts and screws for
proper tightness to be sure the machine is in safe
working condition. Also, visually inspect the chipper
shredder at frequent intervals for any damage.
GXi Outdoor Power products are designed to give safe
and dependable service if operated according to
instructions. Read and understand this owner’s manual
before operating your power equipment.
6. Maintain or replace safety and instructions labels, as
necessary.
Operator Responsibility
Know how to stop your power equipment quickly in case
of emergency. Understand the use of all controls and
connections. Be sure that anyone who operates this
power equipment receives proper instruction. Do not let
children operate the power equipment without parental
supervision.
7. To avoid personal injury or property damage use
extreme care in handling gasoline.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine
is hot or running.
e. Allow engine to cool at least two minutes before
refueling.
f. Never over fill fuel tank. Leave at least 1/2 inch
open below bottom of filler neck to provide space
for fuel expansion.
g. Tighten gasoline cap securely.
h. If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area and
wait 5 minutes before starting the engine.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
5
Operating Guidelines
Heavy Duty Power Equipment
READ THESE OPERATING GUIDELINES
BEFORE YOU PROCEED ANY FURTHER
The side chute is for
longer and/or thicker
pieces of yard waste.
Depending on your
model, you may cut up
to a 3” x 4” in diameter
piece of wood.
1. Do not put hands and feet near rotating parts or in the
feeding chambers and discharge opening. Contact with
the rotating impeller can amputate fingers, hands, and
feet.
2. Before starting the machine, make sure the chipper
chute, feed intake, and cutting chamber are empty and
free of all debris.
3. Thoroughly inspect all material to be shredded and
remove any metal, rocks, bottles, cans, or other foreign
objects which could cause personal injury or damage
to the machine.
8. Never attempt to unclog either the feed intake or
discharge opening while the engine is running. Shut
the engine off, wait until all moving parts have
stopped, disconnect the spark plug wire and ground it
against the engine before clearing debris.
4. If it becomes necessary to push material through the
shredder hopper, use a small diameter stick. Do not
use your hands or feet.
9. Never operate without the shredder funnel, chipper
chute, or discharge chute properly attached to the
machine. Never empty or change discharge bag
while the engine is running. Stop the engine when
leaving the operating position.
5. If the impeller strikes a foreign object or if your
machine should start making an unusual noise or
vibration, immediately shut the engine off. Allow the
impeller to come to a complete stop. Disconnect the
spark plug wire, ground it against the engine and
perform the following steps:
10. Keep all guards, deflectors and safety devices in
place and operating properly.
a. Inspect for damage.
b. Repair or replace any damaged parts.
11. Keep your face and body back and to the side of the
chipper chute while feeding material into the machine
to avoid accidental kickback injuries.
c. Check for any loose parts and tighten to assure
continued safe operation.
12. Never operate this machine without good visibility or
light.
6. Do not allow an accumulation of processed material to
build up in the discharge area. This can prevent proper
discharge and result in kickback of material through
the feed opening.
13. Do not operate on a non-level surface.
14. Do not operate in a confined space.
7. Do not attempt to shred or chip material larger than
specified on the machine or in this manual. Personal
injury or machine damage could result.
15. Do not operate this machine while under the
influence of alcohol or drugs.
16. Muffler and engine become hot and can cause a
burn. Do not touch.
The funnel on the chipper/
shredder is for dry leaves
only. Do not use the
17. Never pick up or carry machine while the engine is
running.
funnel for vines or long
branches such as
Weeping Willows as
they may clog the flails.
18. Do not leave this machine running while unattended
19. Keep children, bystanders, and pets 75 feet away.
20. Use only manufacturer approved accessories/
attachments.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
6
Assembly
Heavy Duty Power Equipment
Second, place the funnel over the opening on the
Required tools: A Philips head screw driver
chipper box, ensuring the rubber gasket is correctly
aligned. Secure the funnel with the two “swing up bolts”
and the one fixed bolt using the wrench provided. Tighten
the nuts securely.
Approximate assembly time: 10 minutes
1. Remove the chipper from its carton.
Remove staples, break glue on top flaps, or cut tape at
carton end and peel along top flap to open carton.
2. Verify all parts are in the chipper
carton.
Chipper Funnel
Chipper engine
and box
assembly
(pre-assembled)
Chipper Chute
Hardware Bag
Trailer hitch and
funnel handles
packaged
together
5. Attach the side chipper chute.
Place the chipper chute over the four bolts protruding
from the side of the chipper box and secure the nuts
tightly using the wrench provided.
3. Disconnect the spark plug wire.
Before setting up your chipper/shredder, disconnect the
spark plug wire from the spark plug and ground against
the engine to prevent inadvertent starting. This step
should be taken as a precaution whenever you are
working on this machine.
4. Attach the chipper funnel.
First, attach the two handles to the sides of the funnel
using the wrench provided and a Phillips head screw
driver. Tighten the nuts securely.
6. Attach the chip collection bag.
Place the metal grommets of the bag over the wire loops
located at the base of the engine. Wrap the bag under
the bottom of the discharge chute and pull the draw string
tightly and secure it.
7. Attach the trailer hitch.
Place the trailer hitch into the socket at the base of the
chipper over the axle assembly. Insert the pin and secure
with the locking cotter pin.
8. Re-connect the spark plug wire.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
7
Important Engine Information
Heavy Duty Power Equipment
DEK Engine Only—See Manufacturer’s manual for other engines
NOTE: The chipper/shredder operates most
efficiently at the factory set engine speed of 3600
RPM. The speed is controlled by the governor,
and the throttle setting should not be adjusted.
Do not attempt to adjust the speed of the engine.
Carbon Monoxide Gas
Exhaust contains poisonous carbon monoxide, a
colorless and odorless gas. Breathing exhaust can cause
loss of consciousness and may lead to death. To keep
exhaust gas from accumulating, DO NOT use this
product in a garage, basement, crawlspace, enclosed
shed, or any other area without adequate ventilation. DO
NOT use this equipment near ventilation ducts or open
windows that may allow exhaust gasses to enter your
home or business. ONLY operate this product outdoors.
Emission Control System Information
The U.S. and California Clean Air Acts
EPA and California regulations require all manufacturers
to furnish written instructions describing the operation and
maintenance of emission control systems. The following
instructions and procedures must be followed in order to
keep the emissions from your DEK engine within the
emission standards.
The engine exhaust from this product and other
components contain chemicals known to the State of
California to cause cancer, birth defects or other
reproductive harm.
The emission control systems on your DEK engine were
designed, built, and certified to conform with EPA and
California emission regulations.
Maintenance, replacement, or repair of the emission
control devices and systems may be performed by any
engine repair provider, using parts that are ‘‘certified’’ to
EPA standards.We recommend the use of genuine DEK
parts whenever you have maintenance done. These
original-design replacement parts are manufactured to the
same standards as the original parts, so you can be
confident of their performance.
Fire and Burn Hazards
The use of aftermarket replacement parts, not of the
original design and quality, may impair the effectiveness of
your emission control system. A manufacturer of an
aftermarket part assumes the responsibility that the part
will not adversely affect emission control performance and
must certify that use of the part will comply with emission
regulations.
The exhaust system gets hot enough to ignite some
materials.
Keep the power equipment at least 3 feet (1 meter)
away from buildings and other equipment during
operation.
Do not enclose this product in any structure.
Do not smoke when refueling.
Keep flammable materials away.
The muffler becomes very hot during operation and
remains hot for a while after stopping the engine. Be
careful not to touch the muffler while it is hot.
Let the engine cool before storing.
Refuel in a well ventilated area with the engine
stopped.
In the State of California a spark arrestor is required by
law. Other states may have similar laws. Federal laws
apply on all federal lands. If you equip the muffler with a
spark arrestor, it must be maintained in effective working
order.
Fuel vapors are extremely flammable and may
ignite after the engine has started. Make sure that
any spilled fuel has been wiped up before starting
the engine.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
8
Operating Instructions
Heavy Duty Power Equipment
steps until engine fires.
Rapid retraction of the recoil starter cord can pull the
starter cord back faster than you can let go. When
starting the engine, pull the cord slowly until
This machine was built to be operated according to the
rules for safe operation in this manual. As with any type of
power equipment, carelessness or error on the part of the
operator can result in serious injury.
resistance is felt then pull rapidly to avoid kickback.
Step 7: Electric start: Follow Step 3 to Step 5, then plug any 120V
outdoor extension cord into the 120V Extension Cord Connection (See
Figure 1), and then push the Red Starter Button to start the engine. Do
not run starter more than 10 times at intervals of 5 seconds On / 5
seconds Off.
Always wear hearing and eye protection while
operating this machine or if you are within 75 feet of
this machine.
Step 8: When engine starts, move choke control
gradually to the RUN position.
Step 9: After engine is started, gradually release choke.
IMPORTANT: This unit is shipped
without gasoline or oil in the engine.
Be certain to fill the engine with
gasoline and oil as instructed before
operating your machine.
NOTE: A noise will be heard when finding the start of the
compression cycle. This noise is caused by the flails and
fingers, which are part of the shredding mechanism, and
it should be expected until the impeller reaches full
speed.
Figure 1
Add Gasoline and Oil
Step 1: Add gasoline
Step 2: Add approximately 1.1 quarts of 10W-30 oil until
the oil is about to overflow from the oil fill spout. A low oil
sensor will prevent the engine from running unless the oil
is COMPLETELY FULL. Ensure both oil fill plugs are
secure after filling.
Never fill fuel tank indoors with engine running or
until the engine has been allowed to cool for at least
two minutes after running.
Starting the Engine
Step 3: Attach spark plug wire to spark plug. Make certain
the metal cap on the end of the spark plug is fastened
securely over the metal tip on the spark plug.
Figure 2
Step 4: Move choke lever on engine to CHOKE position.
(A warm engine may not require choking).
Step 5: Turn the fuel valve to the ON position.
Step 6: Grasp starter handle and pull rope out slowly until
engine reaches start of compression cycle (rope will pull
slightly harder at this point). Pull rope with a rapid,
continuous, full arm stroke. Keep a firm grip on starter
handle. Let the rope rewind slowly. Repeat the previous
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
9
Operating Instructions
Heavy Duty Power Equipment
Using the Chipper Shredder
WARNING
Yard waste such as leaves and pine needles can be
raked up and placed in the funnel assembly for shredding.
DO NOT PUT BRANCHES INTO THE TOP FUNNEL.
BRANCHES SHOULD BE FED INTO THE SIDE CHIPPER
CHUTE.
To Empty the Chip Bag
Stop the engine.
Release the drawstring and remove the bag from the dis-
charge chute.
Empty bag and reattach to the discharge chute opening.
If using the side chipper chute to chip branches, it is im-
portant to let the chipper feed the branches through auto-
matically. DO NOT attempt to force the branches through.
If the branches do not automatically feed through, gently
push the branch and then allow the chipper to automati-
cally feed the branch through. Forcing branches into the
side chute may wear the belt prematurely.
After the material has been shredded by the flail blades on the
impeller assembly, it will be discharged out of opening or into
chip catcher bag.
Do not attempt to shred or chip any material other than
vegetation found in a normal yard (i.e. branches, leaves, twigs,
etc.) Avoid fibrous plants such as tomato vines until they are
thoroughly dried out. Twigs and small branches up to 4” in
diameter can be fed into the chipper chute.
IMPORTANT: The flail screen is located inside the housing in
the discharge area. If the flail screen becomes clogged, remove
and clean as instructed. For best performance, it is also
important to keep the chipper blade sharp.
WARNING
Do not attempt to use the side chute while using the
funnel at the same time. The chipper will bog down and will
vibrate violently causing premature wear.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
10
Maintenance and Storage
Heavy Duty Power Equipment
Maintenance Schedule
20 hrs or 50 hrs or
100 hrs or
every 6
months
300 hrs or
every 1
year
Before each
use
Item
every 3
months
every 3
months
Engine Oil (Check)
Engine Oil (Change)
Air Cleaner (Check)
Air Cleaner Wash
X
X
X
X
Fuel filter Cup (Clean)
Spark Plug (Clean)
X
X
Spark Plug (Change)
X
Lubricate Release Bracket
Lubricate Hopper Assembly
Check Chipper Blade
X
X
X
Fuel Tank and Filter (Clean)
X
6. Follow this manual for safe loading, unloading,
transporting, and storage of this machine.
7. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light such
as a water heater, furnace, clothes dryer, etc.
Always stop engine, disconnect spark plug, and
ground against engine before cleaning,
lubricating or doing any kind of maintenance on
your machine.
8. Always refer to the operator’s manual for proper
instructions on off-season storage.
9. If the fuel tank has to be drained, do this outdoors.
Maintenance and Storage
10. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
1. Never tamper with safety devices. Check their proper
operation regularly.
If the Chipper Becomes Clogged:
2. Check bolts and screws for proper tightness at
frequent intervals to keep the machine in safe working
condition. Also, visually inspect machine for any
damage and repair, if needed.
If the discharge area becomes clogged:
Stop the engine. Disconnect spark plug wire from
spark plug and ground against the engine.
Remove the large funnel and the clean out the
access hatch on the side of the chipper engine box
(as necessary).
Reach in and clear the debris causing the blockage.
Reinstall the funnel and the clean out access hatch.
Connect the spark plug wire and restart.
3. Before cleaning, repairing, or inspecting, stop the
engine and make certain the impeller and all moving
parts have stopped. Disconnect the spark plug wire
and ground it against the engine to prevent
unintended starting.
4. Do not change the engine governor settings or
overspeed the engine. The governor controls the
maximum safe operating speed of the engine.
NOTE: If the blockage is severe, the hammer screen
within the discharge chute can be removed as well,
providing greater access. To accomplish this, remove the
pins and slide the flail screen out of the discharge chute.
5. Maintain or replace safety and instruction labels, as
necessary.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
11
Maintenance & Storage
Heavy Duty Power Equipment
Scribe a mark on the base plate along the edge of
the engine.
Remove the belt from the pulleys.
Remove the handle, discharge chute and screen.
Loosen the four bolts securing the engine.
Slide the engine about 1/8” further back.
Tighten the engine mounting bolts securely.
Re-install the belt and verify the tension. If the belt is
still too loose, move the engine back another 1/8” by
repeating the above steps.
Always stop engine, disconnect spark plug, and
ground against engine before cleaning,
lubricating or doing any kind of maintenance on
your machine.
Removing and Sharpening the Blade
Reinstall guards, chutes, and screens.
The chipper was shipped with one blade attached and
one blade in the hardware bag. You can extend the belt
life by operating the chipper with a sharp blade.
Disconnect the spark plug wire and ground against
the engine.
Cleaning the Chipper/Shredder
Make sure engine is off.
Wipe off machine with an oiled rag to prevent rust.
If the fuel tank has to be drained, do so outdoors.
Observe proper disposal laws and regulations for
gas, oil, etc., to protect the environment.
Remove the blade access hatch and rotate the
blade to align with the access hatch.
Remove the flail screen in the discharge chute by
removing the pins that secure it at the top and
bottom of the screen.
Storing the Chipper/Shredder
Clean the equipment thoroughly.
Remove the blade using a 3/16” Allen wrench on the
outside of the blade and an adjustable wrench on
the impeller assembly (through the discharge
chute). Use a piece of pipe or wood to block the
flails, preventing them from inadvertently turning.
Add, replace or sharpen the blade as desired.
When sharpening the blade, protect hands by using
gloves and following the original angle of
grind.Torque to 250–300 in. lbs.
Wipe equipment with an oiled rag to prevent rust.
Refer to engine manual for correct engine storage
instructions.
Store unit in a clean, dry area. Do not store next to
corrosive materials such as fertilizer.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
such as a water heater, furnace, clothes dryer, etc.
NOTE: Make certain the blade is reassembled with the
sharp edge facing upward.
Changing or Tightening the Belt
NOTE: The belt is designed to be the weakest link in the
mechanical linkage between the engine and the blade.
This improves the safety and durability of the chipper/
shredder.
Occasionally, changing or tightening the belt is required.
To change the belt:
Stop the engine and make certain the chipper/
shredder has come to a complete stop. Disconnect
the spark plug wire from spark plug and ground
against the engine.
Remove the belt guard.
Loosen engine mount bolts and release belt tension.
Pry the belt off the pulley using a screw driver shaft
as a wedge as you rotate the pulley. Place a new
belt on the pulleys in a similar fashion.
To tighten the tension on the pulleys, follow the above
steps plus:
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
12
Troubleshooting
Heavy Duty Power Equipment
Problem
Cause
Remedy
1. Spark plug wire disconnected.
2. Fuel tank empty or stale fuel.
1. Connect wire to spark plug.
Engine fails to start
2. Fill tank with clean, fresh gasoline.
3. Move throttle lever to FAST position.
3. Throttle control lever not in correct
starting position. (If equipped)
4. Choke not in CHOKE position. (If
equipped)
4. Move choke to CHOKE position.
5. Prime engine.
5. Engine not primed.
6. Blocked fuel line.
7. Faulty spark plug.
8. Low oil
6. Clean fuel line.
7. Clean, adjust gap, or replace.
8. Fill
1. Spark plug wire loose.
1. Connect and tighten spark plug wire.
2. Move choke lever to OFF position.
Engine runs erratic
2. Unit running on CHOKE. (If equipped)
3. Blocked fuel line or stale fuel.
4. Water or dirt in fuel system.
5. Dirty air cleaner.
3. Clean fuel line; fill tank with clean, fresh
gasoline.
4. Drain fuel tank. Refill with fresh fuel.
5. Clean or replace air cleaner.
6. See authorized service dealer
6. Carburetor out of adjustment.
1. Loose parts or clogged flail.
2. Trying to force branches or logs too fast into
the side chute
3. Trying to force branches in the funnel or
attempting to put branches into funnel while
side chute is in use
1. See authorized service dealer.
2. Cut off excess limbs off of large branches and
ensure blades are sharp
3. Allow the branches to feed through the side
chute first before attempting to use the funnel.
Also do not put branches in the funnel.
Too much vibration
Engine overheats
1. Engine oil level low.
1. Fill crankcase with proper oil.
2. Clean or replace air cleaner.
3. See authorized service dealer.
2. Dirty air cleaner.
3. Carburetor not adjusted properly.
1. Adjust gap to.030”.
1. Spark plug gap too close.
Occasional skip
(hesitates)
1. Discharge chute clogged.
2. Foreign object lodged in impeller.
3. Low engine RPM.
1. Stop engine immediately and disconnect
spark plug wire. Clean flail screen and
inside of discharge opening.
Unit does not discharge
2. Stop engine and disconnect spark plug
wire. Remove lodged object.
3. Always run engine at full throttle.
1. Low engine RPM.
2. Chipper blade dull.
1. Always run engine at full throttle
Rate of discharge slows
2. Replace chipper blade or see your
authorized service dealer.
NOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized service dealer.
Rev: 04/2015
Brush Master™ Chipper/Shredder with 2-Way Feed
13
Limited Warranty & Service
Heavy Duty Power Equipment
Length of Warranty: *(from the date of original retail
purchase)
Noncommercial Commercial
/Nonrental
Products Covered by this
Warranty
Rental
Engine
12 months
12 months
12 months
*Length of Warranty: Consumable parts such as oil, spark plugs, filters, blades, and belts are not covered by this warranty. Warranty repairs will be
made without charge for parts and labor for the first 6 months. After the first 6 months, the limited warranty covers the costs of replacement parts only.
To Qualify for this Warranty:
The product must be purchased in the United States from a dealer authorized by GXi Outdoor Power, LLC to sell the product. This warranty applies to
first retail purchaser/owner during the applicable warranty time period. No warranty registration is necessary to obtain warranty on Brush Beast or Turf
Beast products. Save your proof of purchase receipt.
To Obtain Warranty Service:
You must take the DEK Power Equipment product, accessory, replacement part, apparel or the power equipment on which the accessory or
replacement part is installed, and proof of purchase, at your expense, to any DEK Power Equipment service location in the United States, who is
authorized to service that product, during the service location’s normal business hours. If you are unable to obtain warranty service, or are dissatisfied
with the warranty service you receive, take the following steps: First, contact the manager of the service center involved; normally this will resolve the
problem. However, if you should require further assistance, write or call the GXi Customer Service.
What GXi Outdoor Power Will Repair or Replace under Warranty:
GXi will repair or replace, at its option, any part that is proven to be defective in material or workmanship under normal use during the applicable
warranty time period subject to the exclusions stated herein. GXi has the right to recover warranty administration costs from the owner if the root
cause of the malfunction is found to be other than defective material or workmanship. This warranty is void if the owner fails to follow the prescribed
operating, maintenance and storage procedures described in this manual. This specifically refers to ensuring routine oil changes are made, that fuel
stabilizer is used for long-term storage and that the chipper/shredder is used in accordance with the operating instructions.
Anything replaced under warranty becomes the property of GXi. Parts replaced under warranty will be considered as part of the original product and
any warranty on those parts will expire coincident with the original product warranty.
Exclusions:
This warranty does not cover: normal wear, contaminants in the fuel or oil; damage as a result of use in an application for which the product was not
designed; damage caused by incorporation or use of unsuitable attachments or parts, unauthorized alteration, or other misuse and neglector; damage
caused by failure to follow the prescribed warnings, operating practices, proper maintenance and storage procedures; parts affected or damaged by
accident and/or collision; damage due to shipping, handling, storage or any causes other than defects in material or workmanship of the product.
Disclaimer of Consequential Damage and Limitation of Implied Warranties:
GXI disclaims any responsibility for loss of time or use of the product, transportation, commercial loss, or any other incidental or consequential
damage. Any implied warranties are limited to the duration of this written limited warranty.
THIS WARRANTY IS VOID IF THE MANUFACTURING DATE AND THE SERIAL NUMBER ON THE EQUIPMENT HAS BEEN REMOVED OR
THE EQUIPMENT HAS BEEN MODIFIED.
EMISSION CONTROL SYSTEM INFORMATION
The U.S. and California Clean Air Acts
EPA and California regulations require all manufacturers to furnish written instructions describing the operation and maintenance of emission control
systems. The following instructions and procedures must be followed in order to keep the emissions from your STANLEY engine within the emission
standards. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any engine repair establishment or
individual, using parts that are ‘‘certified’’ to EPA standards.
The emission control systems on your STANLEY engine were designed, built, and certified to conform with EPA regulations. We recommend the use
of genuine STANLEY parts whenever you have maintenance done. These original-design replacement parts are manufactured to the same standards
as the original parts, so you can be confident of their performance. The use of replacement parts that are not of the original design and quality may
impair the effectiveness of your emission control system. A manufacturer of an aftermarket part assumes the responsibility that the part will not
adversely affect emission performance. The manufacturer or re-builder of the part must certify that use of the part will not result in a failure of the
engine to comply with emission regulations.
Emission controls are covered by this warranty for all uses for a period of 3 years from original retail purchase date, this coverage extends to
subsequent owners of the product with proof of original purchase.
Rev: 04/2010
Brush Master™ Chipper/Shredder with 2-Way Feed
14
Turf Beast
The Beast
Brush Beast
Brush Master
or visit our web site at www.beastpowerequipment.com
Turf Beast
Turf Beast
36 in. Walk
Behind Mower
54 in. Walk
Behind Mower
The Beast
100 in. Tow
Behind Mower
Brush Beast
36 in Brush Mower.
|