DISHLEX DX 103 User Manual

User manual  
Dishwasher  
DX 103  
• A qualified and competent person must do the  
plumbing installation.  
Contact your local Customer Care Centre.  
• Do not drill into the sides of the appliance otherwise  
damage to hydraulic and electrical components may  
occur.  
• Do not change the specifications or modify this prod-  
uct. Risk of injury and damage to the appliance.  
• Do not use the appliance:  
Warning! Carefully obey the instructions for  
electrical and water connections.  
– if the mains cable or water hoses are damaged,  
– if the control panel, worktop or plinth area are  
damaged so that you can get access to the inner  
side of the appliance.  
Control panel  
1 Program knob  
2 Start/cancel button  
3 Indicator light 'Finished'  
4 On/off indicator light  
5 Program marker  
Indicator lights  
Finished  
Comes on when the washing program is completed. It also has  
the auxiliary functions of alarm if the appliance has a malfunction.  
– The on/off indicator light comes on (position ON).  
Program knob and on/off indicator light  
• To set the appliance to the off position, turn the pro-  
gram knob until the program marker agrees with the  
on/off indicator light.  
• To set a washing program, turn the program knob  
clockwise or anticlockwise. The program marker on  
the program knob must agree with one of the wash-  
ing program on the control panel.  
– The on/off indicator light goes off (position OFF).  
3
Washing programmes  
Program  
Degree of soil  
Heavy soil  
Type of load  
Program description  
Prewash  
Main wash up to 70°C  
2 intermediate rinses  
Final rinse  
Pots  
Crockery, cutlery,  
pots and pans  
Drying  
Regular Plus  
Normal soil  
Crockery and cutlery Prewash  
Main wash up to 65°C  
2 intermediate rinses  
Final rinse  
Drying  
1)  
Normal or light soil  
Normal soil  
Crockery and cutlery Main wash up to 65°C  
Quick 30  
(Partial load)  
Crockery and cutlery Prewash  
Main wash up to 50°C  
Final rinse  
2)  
Regular Eco  
1 intermediate rinse  
Final rinse  
Drying  
Rinse & Hold  
Any  
Partial load (to be  
1 cold rinse (to prevent food  
completed later in the scraps to bond).  
day). Detergent is not necessary with  
this program.  
1) This is the perfect daily program to clean a partial load. Ideal for a family of 4 persons who only want to load breakfast and  
dinner crockery and cutlery.  
2) Test program for test institutes. Please refer to separate leaflet supplied, for test data.  
Consumption values  
Program  
Duration (in minutes)  
Energy (in kWh)  
1,8 - 2,0  
Water (in litres)  
22 - 25  
Pots  
85 - 95  
100 - 115  
30  
Regular Plus  
Quick 30  
1,5 - 1,7  
0,9  
23 - 25  
9
Regular Eco  
Rinse & Hold  
90 - 100  
12  
0,83 - 0,91  
0,1  
16 - 18  
5
The pressure and temperature of the water, the  
variations of power supply and the quantity of  
dishes can change these values.  
Use of the appliance  
1. Fill the rinse aid dispenser with rinse aid.  
2. Load cutlery and dishes into the dishwasher.  
Refer to specified instructions for each step of the pro-  
cedure.  
4
3. Set the correct washing program for the type of  
load and soil.  
5. Start the washing program.  
4. Fill the detergent dispenser with the correct quan-  
tity of detergent.  
Use of rinse aid  
Caution! Only use rinse aid specified for  
dishwashers.  
Caution! Do not fill the rinse aid dispenser with  
other products (e.g. dishwasher cleaning agent,  
liquid detergent). There can cause damage to the  
appliance.  
Follow these steps to fill the rinse aid dispenser:  
Adjusting the rinse aid dosage  
The rinse aid is set at the  
factory at position 3.  
To increase or decrease  
the dosage refer to 'What  
to do if...'  
1
3
5
2
4
Wash hands to remove any residue of rinse aid  
from skin.  
Fill when the rinse aid in-  
dicator (B) becomes  
clear.  
Loading cutlery and dishes  
• Before you load cutlery and dishes, do these steps:  
– Remove all food remainings and debris.  
– Make burnt, remaining food in pans soft.  
Helpful hints and tips  
Caution! Only use the appliance for household  
utensils that are suitable for dishwashers.  
Do not use the appliance to clean objects that can ab-  
sorb water (sponges, household cloths, etc.).  
5
• While you load cutlery and dishes, do these steps:  
Use the cutlery grid for best washing results. If the di-  
mensions of the cutlery prevent use of the cutlery grid,  
remove it.  
– Load hollow items (e.g. cups, glasses and pans)  
with the opening down.  
– Make sure that water does not collect in the con-  
tainer or in a deep base.  
– Make sure that cutlery and dishes do not lie inside  
one another.  
– Make sure that cutlery and dishes do not cover  
other cutlery and dishes.  
– Make sure that glasses do not touch other  
glasses.  
1
2
– Put small objects in the cutlery basket.  
Arrange the items to let  
water touch all surfaces.  
For longer items, fold the  
cup racks up.  
• Plastic items and pans with non-stick coatings can  
retain water droplets. Plastic items do not dry as well  
as porcelain and steel items.  
Prevent to put plates in the first three sectors in  
the front part of the basket. Make sure the plates  
• Put light items in the upper basket. Make sure that  
the items do not move.  
tilt forward.  
Caution! Make sure that the spray arms can  
move freely before you start a washing program.  
Adjustment of the height of the upper basket  
If you put large plates in the lower basket, first move  
the upper basket to a upper position.  
Warning! Always close the door after you load  
or unload the appliance. An open door can be  
dangerous.  
Warning! Adjust the height before you load the  
upper basket.  
Maximum height of the dishes in :  
upper basket lower basket  
Upper position  
Lower position  
20 cm  
24 cm  
31 cm  
27 cm  
1
2
Arrange service dishes  
and large lids around the  
edge of the lower basket.  
1
2
Follow these steps to move the upper basket to the  
upper or lower position:  
1. Move the front runner stops (A) out.  
2. Pull the basket out.  
1
2
3. Put the basket in the upper or lower position.  
6
4. Replace the front runner stops (A) in their initial  
position.  
Caution! If the basket is in the upper position,  
do not put cups on the cup racks.  
Use of detergent  
Only use detergents (powder, liquid or tablet) that  
are suitable for dishwashers.  
Follow the data on the packaging:  
Different brands of detergent dissolve in different  
times. Some detergent tablets do not have the  
best cleaning results during short washing programs.  
Use long washing programs when you use detergent  
tablets to fully remove the detergent.  
• dosage recommended by the manufacturer,  
• storage recommendations.  
Use of combi detergent tablets  
Do not use more than the correct quantity of de-  
tergent to decrease pollution.  
These products are detergents with a combined clean-  
ing and rinsing functions. They can contain also other  
cleaning agents.  
Refer to the instructions from the manufacturer for the  
use of these products.  
With tablets that contain rinse aid:  
• set the lowest position for the rinse aid dosage,  
• do not put rinse aid in the rinse aid dispenser. In this  
condition rinse aid indicator light is always on when  
you switch on the appliance.  
1
3
2
4
.
Do these steps if the drying results are not satis-  
factory:  
1. Fill the rinse aid dispenser with rinse aid.  
2. Set the rinse aid dosage to position 2.  
If you go back to use normal detergents again, fill  
the rinse aid dispenser and adjust the rinse aid  
dosage.  
Fill the detergent dis-  
penser (A) with deter-  
gent.  
If you use a washing pro-  
gram with prewash  
phase, put more deter-  
gent in the prewash de-  
tergent compartment (B).  
5
6
7
Select and start a washing program  
Do these steps to set and start a washing program:  
1. Close the door.  
Fill the detergent dispenser with detergent before  
you set a new washing program.  
2. Turn the program knob to setthewashing program.  
Refer to the chapter 'Washing programs'.  
Interrupting a washing program  
Open the door.  
– The on/off indicator light comes on.  
3. Press the start/cancel button.  
• The program stops.  
Close the door.  
– The washing program starts automatically.  
– The start/cancel indicator light comes on.  
• The programcontinuesfromthepointofinterruption.  
End of the washing program  
• The appliance stops automatically.  
• The 'Finished' indicator light comes on.  
1. Switch off the appliance.  
When the washing program operates, you cannot  
change the program. Cancel the washing pro-  
gram.  
Warning! Only interrupt or cancel a washing  
program if necessary.  
Attention! Open the door carefully. Hot steam and  
water can escape.  
2. Open the door.  
3. For better drying results, keep the door ajar for  
some minutes before you remove the dishes.  
Let the dishes cool down before you remove them from  
the appliance. Hot dishes are easily damaged.  
Cancelling a washing program  
Removing the load  
• First remove items from the lower basket, then from  
the upper basket.  
• Press and hold the start/cancel button until the start/  
cancel indicator light goes off.  
The washing program is cancelled.  
At this time you can do these steps:  
• There can be water on the sides and door of the  
appliance. Stainlesssteelbecomescoolmorequick-  
ly than the dishes.  
1. Switch off the appliance.  
2. Set a new washing program.  
Care and cleaning  
Warning! Switch the appliance off before you  
clean it.  
Cleaning the filters  
Important! Do not use the appliance without the filters.  
Make sure that the installation of the filters is correct.  
Incorrect installation will cause unsatisfactory washing  
results and damage to the appliance.  
1
2
Fully clean the filters A, B  
and C below running wa-  
ter.  
8
tergents. Do not use abrasive products, scouring pads  
or solvents (acetone etc.).  
Internal cleaning  
Doaninspectionatintervals of3months. Setawashing  
program for heavily soiled dishes. Use detergent, but  
do not put dishes in the appliance.  
Long periods of non-operation  
Do these steps when you do not use the appliance for  
a long period:  
3
4
To remove filters B and Remove the flat filter A  
1. Disconnect the mains plug from the mains socket.  
2. Close the water tap.  
C, turn the handle ap-  
proximately 1/4 anti-  
clockwise.  
from the bottom of the ap-  
pliance.  
3. Keep the door open to prevent unpleasant smells.  
4. Keep the inner side of the appliance clean.  
Frost precautions  
Caution! Do not install the appliance where the  
temperature is below 0 °C. The manufacturer is  
not responsible for damage because of frost.  
If not possible, empty the appliance and close the door.  
Disconnect the water inlet hose and remove water from  
the water inlet hose.  
5
6
Put the filter A in the bot- Put the filter system in po-  
tom of the appliance. In- sition. To lock the filter  
stalltheflatfiltercorrectly system, turn the handle  
under the two guides D. clockwise until it locks in  
position  
Moving the machine  
Do these steps to move the appliance:  
1. Disconnect the mains plug from the mains socket.  
2. Close the water tap.  
3. Remove the appliance and the hoses.  
4. Do not tilt the appliance during transport.  
Important! Do not remove the spray arms.  
If the holes in the spray arms become clogged, remove  
remaining parts of soil with a cocktail stick.  
External cleaning  
Clean the external surfaces of the appliance and con-  
trol panel with a damp soft cloth. Only use neutral de-  
What to do if…  
The appliance does not start or stops during operation.  
If there is a fault, first try to find a solution to the problem  
yourself. Refer to following charts. If you cannot find a  
solution to the problem yourself, contact your dealer or  
the Customer Care Centre.  
Warning! Switch the appliance off before you do  
the suggested corrective actions.  
9
Fault code and malfunction  
Possible cause and solution  
• continuous flash of the start/cancel  
indicator light  
• The water tap is blocked or furred with limescale.  
Clean the water tap.  
• 1 flash of the 'Finished' indicator light • The water tap is closed.  
The appliance does not fill with water  
Open the water tap.  
• The filter in the water inlet hose is blocked.  
Clean the filter.  
• The connection of the water inlet hose is not correct. The hose  
can be kinked or squashed.  
Make sure that the connection is correct.  
• continuous flash of the start/cancel  
indicator light  
• There is a blockage in the sink spigot.  
Clean the sink spigot.  
• 2 flashes of the 'Finished' indicator  
light  
• The connection of the water drain hose is not correct. The hose  
can be kinked or squashed.  
The appliance will not drain  
Make sure that the connection is correct.  
The program does not start  
• The appliance door is not closed.  
Close the door.  
• Mains plug is not connected.  
Plug-in appliance to the mains.  
• The fuse has blown out in the household fuse box.  
Replace the fuse.  
After the check, switch on the appliance. The program • Product number (PNC)  
continues from the point of interruption. If the malfunc-  
tion shows again, contact your Customer Care Centre.  
For otherfault codes, notdescribed inthe chart, contact  
your Customer Care Centre.  
These data are necessary to help you quickly and cor-  
rectly:  
• Serial number (S.N.)  
For these data, refer to the rating plate.  
Write the necessary data here:  
Model description : ..........  
Product number : ..........  
Serial number : ..........  
• Model (Mod.)  
The cleaning results are not satisfactory  
The dishes are not clean  
• The selected washing program is not applicable for the type of load and  
soil.  
• The baskets are loaded incorrectly so that water cannot reach all surfaces.  
• Spray arms do not turn freely because of incorrect arrangement of the  
load.  
• The filters are dirty or not correctly installed.  
• The quantity of detergent is too little or missing.  
The dishes are wet and dull  
• No rinse aid has been used.  
• The rinse aid dispenser is empty.  
10  
The cleaning results are not satisfactory  
There are streaks, milky spots or • Decrease the rinse aid dosage.  
a bluish coating on glasses and  
dishes  
Dry water drop stains on glasses • Increase rinse aid dosage.  
and dishes  
• The detergent can be the cause.  
Technical data  
Dimensions  
Width (mm)  
Height (mm)  
Depth (mm)  
596  
850  
610  
Electrical connection - Voltage -  
Overall power - Fuse  
Information on the electrical connection is given on the rating plate on the  
inner edge of the dishwasher door.  
Water supply pressure  
Minimum  
50 kPa (7 psi)  
800 kPa (116 psi)  
12  
Maximum  
Capacity  
Place settings  
Environment concerns  
The packaging materials are environmentally friendly  
and can be recycled. The plastic components are iden-  
tified by markings, e.g. >PE<, >PS<, etc. Discard the  
packaging materials in the applicable container at the  
community waste disposal facilities.  
Old appliance  
Make sure that the appliance goes to the applicable  
collection point for recycling.  
Make sure that this appliance is discarded correctly.  
Inappropriate waste discard of the appliance causes  
negative consequences for the environment and hu-  
man health.  
Warning! To discard the appliance, follow the  
procedure:  
For more information about the recycling of this appli-  
ance, contact your local city office, your household  
waste disposal service or the shop where you pur-  
chased the appliance.  
• Pull the mains plug out of the socket.  
• Cut off the mains cable and mains plug and discard  
them.  
• Discard the door catch. This prevents children clos-  
ing themselves inside the appliance and endanger-  
ing their lives.  
Installation  
The plinth on freestanding appliance is not adjustable.  
Do not remove the appliance worktop if you want to use  
the dishwasher as a freestanding appliance.  
Remove the appliance worktop to install it under a sink  
unit or a kitchen worktop.  
Fitting under a counter  
Warning! Make sure that mains plug is  
disconnected from the mains socket during  
installation.  
Make sure that the dimensions of the recess agree with  
the given dimensions.  
Put the appliance adjacent to a water tap and a water  
drain.  
11  
the door does not catch on the sides of the cabinet. If  
the door does not close correctly, loosen or tighten the  
adjustable feet until the appliance is level.  
Adhesive steam protection foil  
If the worktop is removed, fit the steam protection onto  
the front part of the kitchen cabinet benchtop.  
1
3
2
4
The steam protection foil is not supplied with free-  
standing models, but can be purchased from  
Electrolux Spare Parts.  
Adjusting the level of the appliance  
Make sure that the appliance is level to close and seal  
the door correctly. If the level of the appliance is correct,  
Water connection  
Fit the hose nut correctly to prevent water leaks.  
Water inlet hose  
Connect the appliance to a cold water supply.  
Connect the inlet hose to a water tap with an external  
BSP thread spout of 3/4”.  
Caution! Do not connect the appliance to new  
pipes or pipes that have been not used for a long  
time. Let the water run for some minutes, then connect  
the inlet hose.  
Inlet water supply  
• Cold water pressure: 800 kPa max - 50 kPa min.  
• Water flow rate 10 L / minute min.  
Water drain hose  
The highest point of the drain hose must be no more  
than 60 cm from the floor and must have a continuous  
fall.  
The drain hose can be lengthened using additional  
lengths and connectors. These must be purchased  
from Electrolux SpareParts. Theextensionlength must  
not exceed 2 metres.  
The drain hose must be free of kinks and obstructions.  
Remove the sink plug when the appliance drains the  
water to prevent that the water goes back into the ap-  
pliance.  
If you connect the water drain hose to a trap spigot  
under the sink, remove the plastic membrane. If you do  
not remove the membrane, remaining food can cause  
a blockage in the drain hose spigot.  
• If cold water pressure is in excess of 800 kPa, a  
pressure reducing valve should be used. Check for  
leaks.  
Caution! Always use new hoses when you  
connect the appliance to the water mains. Old  
hoses must not be used. The water inlet hose must be  
examined at an interval of twelve months for  
deterioration and replaced if necessary.  
The water pressure must be in the limits (refer to 'Tech-  
nical data'). Make sure that the local water authority  
gives you the average mains pressure in your area.  
Make sure that there are no kinks in the water inlet hose  
and that the water inlet hose is not squashed or entan-  
gled.  
12  
Caution! Ensure that hoses are not crushed or  
kinked under or behind the appliance.  
The appliance has a security feature to prevent dirty  
water going back into the appliance. If, the spigot of the  
sink has a 'non-return valve', this valve can cause the  
appliance to drain incorrectly. Remove the non-return  
valve.  
Caution! Once connected the inlet hose to the  
water tap, turn the tap on and check that there  
are no leaks.  
Make sure that the water couplings are tight to prevent  
water leakage.  
Electrical connection  
Warning! Safetystandardsrequiretheappliance If necessary, have the domestic wiring system socket  
to be earthed.  
Prior to using the appliance for the first time, ensure  
replaced. If the mains cable has to be replaced, contact  
your local Customer Care centre.  
that the rated voltage and type of supply on the rating The mains plug must be accessible after the appliance  
plate match that of the supply where the appliance is  
to be installed.  
has been installed.  
Never unplug the appliance by pulling on the cable.  
The fuse rating is also to be found on the rating plate. Always pull the plug.  
Always plug the mains plug onto a correctly installed  
approved socket.  
Test the appliance. Run a quick washing program and  
ensure that the appliance fills with water, washes and  
Do not use multi-ways plugs, connectors and extension drains with no leaks.  
cables. This can constitute a fire hazard through  
overheating.  
The manufacturer accepts no liability for failure to  
observe the above safety precautions.  
Warranty  
(NZ) Limited in respect of Appliances pur-  
chased in New Zealand;  
– 'Appliance' means any Electrolux product pur-  
chased by you accompanied by this document;  
FOR SALES IN AUSTRALIA AND NEW ZEALAND  
This document sets out the terms and conditions  
of product warranties for Electrolux branded ap-  
pliances. It is an important document. Please keep  
it with your proof of purchase documents in a safe  
place for future reference should you require serv-  
ice for your Electrolux appliance. General Terms  
and Conditions  
– 'Warranty Period' means  
i) where you use the Appliance for personal,  
domestic or household purposes in Australia  
the period of 24 months and in New Zealand  
the period of 24 months;  
ii) where you use the Appliance for commercial  
purposes, in Australia the period of 0 months  
and in New Zealand the period of 0 months, (if  
the period stated is 0 months you are not cov-  
ered by this product warranty) following the  
date of original purchase of the Appliance;  
1. In this warranty  
– Electrolux' means Electrolux Home Products  
Pty Ltd ABN 51 004 762 341 in respect of Ap-  
pliances purchased in Australia and Electrolux  
13  
– 'you' means the purchaser of the Appliance not  
having purchased the appliance for re-sale,  
and 'your' has a corresponding meaning.  
v) incomplete or improper installation  
vi) incorrect, improper or inappropriate opera-  
tion  
vii) insect or vermin infestation.  
2. This warranty only applies to Appliances pur-  
chased and used in Australia or New Zealand and  
is in addition to (and does not exclude, restrict, or  
modify in any way) any non-excludable statutory  
warranties in Australia or New Zealand.  
– The Appliance is modified without authority  
from Electrolux in writing.  
– The Appliance's serial number or warranty seal  
has been removed or defaced.  
3. Electrolux warrants that, when dispatched from an  
Electrolux warehouse, the Appliance is free from  
defects in materials and workmanship for the War-  
ranty Period.  
– The Appliance was serviced or repaired by  
anyone other than Electrolux or its Authorised  
Service Centres.  
9. This warranty, the contract to which it relates and  
the relationship between you and Electrolux are  
governed by the law applicable in the Australian  
State where the Appliance was purchased or the  
law applicable in New Zealand if the Appliance  
was purchased in New Zealand. Where the Ap-  
pliance was purchased in New Zealand for busi-  
nesspurposes the ConsumerGuaranteeActdoes  
not apply.  
4. During the Warranty Period Electrolux or its Au-  
thorised Service Centre will, at no extra charge if  
your appliance is readily accessible without spe-  
cial equipment, and subject to these terms and  
conditions, repair or replace any parts which it  
considers to be defective. You agree that any re-  
placed Appliances or parts become the property  
of Electrolux. This warranty does not apply to light  
globes, batteries, filters or similar perishable  
parts.  
Limitation of Liability  
10. To the extent permitted by law:  
5. Parts and Appliances not supplied by Electrolux  
are not covered by this warranty.  
– Electrolux excludes all warranties other than as  
contained in this document;  
6. Where you are within an Electrolux service area,  
this warranty covers the cost of transport of the  
Appliance to and from Authorised Service Centres  
of Electrolux and travelling costs for representa-  
tives of the Authorised Service Centre to and from  
your home or business. If you are outside an Elec-  
trolux service area, you will bear these costs. For  
information about whether you are within an Elec-  
trolux service area, please phone 13 13 49 in  
Australia, or 0800 10 66 10 in New Zealand.  
– Electrolux shall not be liable for any loss or  
damage whether direct or indirect or conse-  
quential arising from your purchase, use or  
non-use of the Appliance.  
11. Provisions of the Trade Practices Act and State  
consumer legislation in Australia, and the Con-  
sumer Guarantees Act, the Sale of Goods Act and  
the Fair Trading Act in New Zealand, imply war-  
ranties or conditions, or impose obligations, upon  
Electrolux which cannot be excluded, restricted or  
modified. To the extent permitted by law, the lia-  
bility of Electrolux (if any) arising out of or in rela-  
tion to the Appliance or any services supplied by  
Electrolux shall be limited (where it is fair and rea-  
sonable to do so),:  
7. Proofof purchaseis required before you canmake  
a claim under this warranty.  
8. You may not make a claim under this warranty  
unless the defect claimed is due to faulty or de-  
fective parts or workmanship. Electrolux is not li-  
able in the following situations (which are not ex-  
haustive):  
– in the case of Appliances, at its option, to the  
replacement or repair of the Appliances or the  
supply of equivalent products or the payment  
ofthecostofreplacingtheAppliancesorhaving  
the Appliances repaired or of acquiring equiv-  
alent Appliances. Upon being replaced, parts  
and Appliances become the property of Elec-  
trolux; or  
– The Appliance is damaged by  
i) accident  
ii) misuse or abuse, including failure to properly  
maintain or service  
iii) normal wear and tear  
iv) power surges, electrical storm damage or  
incorrect power supply  
14  
– in the case of services, at its option, to the sup- its Authorised ServiceCentres toexchange information  
ply of the services again or the payment of the in relation to you to enable Electrolux to meet its obli-  
cost of having the services re-supplied;  
gations under this warranty.  
and in the case of Appliances or services supplied Important Notice  
in New Zealand, loss or damage whether direct or Before Calling a Service Technician pleasecheck care-  
indirect or consequential that is reasonably fore-  
seeable.  
fully the operating instructions, service booklet and the  
warranty terms and conditions.  
Privacy  
You acknowledge that in the event that you make a  
warranty claim it will be necessary for Electrolux and  
FOR SERVICE  
SERVICE AUSTRALIA  
FOR SPARE PARTS  
OR TO FIND THE ADDRESS OF  
YOUR NEAREST STATE SERV-  
ICE CENTRE IN AUSTRALIA  
OR TO FIND THE ADDRESS OF  
YOUR NEAREST STATE SPARE  
PARTS CENTRE IN AUSTRALIA  
Please call 13 13 50  
ELECTROLUX HOME PROD-  
UCTS  
Please call 13 13 4 9  
For the cost of a local call (Australia only)  
For the cost of a local call (Australia only)  
FOR SERVICE  
SERVICE NEW ZEALAND  
FOR SPARE PARTS  
OR TO FIND THE ADDRESS OF  
YOUR NEAREST AUTHORISED  
SERVICE CENTRE IN NEW ZEA-  
LAND  
OR TO FIND THE ADDRESS OF  
YOUR NEAREST SPARE PARTS  
CENTRE IN NEW ZEALAND  
Free call 0800 10 66 20  
ELECTROLUX HOME PROD-  
UCTS  
Free call 0800 10 66 10  
(New Zealand only)  
(New Zealand only)  
15  

Wtb Vanilla 100r User Manual
Samsung Aw1000 User Manual
Samsung Am18b1c09 User Manual
Panasonic Cs Xe12eke User Manual
KENWOOD HB660 03 User Manual
John Deere 25 Gallon Tow Behind Sprayer User Manual
FUJITSU SIEMENS AMILO PRO V7010 User Manual
FUJITSU PRIMERGY TX1320 M1 User Manual
CANON POWERSHOT G7 X MARK II User Manual
ACER EMACHINES E732 User Manual