DELL XC6320 User Manual

Dell XC6320 Web-Scaled Hyperconverged  
Appliance  
Owner's Manual  
Contents  
3
4
5
6
1
About the Dell XC6320  
About your system  
The Dell XC6320 system is a web-scale converged appliance based on the Dell PowerEdge C6320 and  
supports 512 GB memory (with 32 GB RDIMMs), six hard drives per node, and up to four nodes per  
chassis.  
Accessing system features during startup  
The following keystrokes provide access to system features during startup.  
NOTE: The hot keys of SAS or SATA card or PXE support are available in BIOS boot mode only.  
There is no hot key to boot in the the UEFI mode.  
F2  
Enters the System Setup program.  
F11  
Enters the BIOS Boot Manager.  
F12  
Starts Preboot eXecution Environment (PXE)/iSCSI boot.  
Ctrl +C  
Enters the LSI 2008 SAS Mezzanine Card Configuration Utility. For more  
information, see the SAS adapter documentation.  
Ctrl+R  
Enters the PERC 9 Card Configuration Utility. For more information, see the  
documentation for your SAS RAID card.  
Ctrl+Y  
Ctrl+S  
Enters the MegaPCLI SAS RAID Management Tool.  
Enters the utility to configure onboard LAN settings for PXE boot. For more  
information, see the documentation for your integrated LAN.  
Ctrl+I  
Enters onboard SATA Controller’s Configuration Utility.  
Enters the Intel iSCSI setup menu.  
Ctrl+D  
7
     
Front panel features and indicators  
Figure 1. Front panel features and indicators  
NOTE: For more information about the direction details of the 2.5-inch hard drive expander  
configuration support, see the HDD Zoning configuration tool at Dell.com/support.  
Table 1. Front-panel features and indicators  
Item Indicator, button or  
connector  
Icon  
Description  
1
System identification indicator  
or button for system board 2  
The identification button can  
be used to locate a particular  
system and system board  
within a chassis. When the  
button is pushed, the blue  
status indicator of the system  
on the front and rear blinks  
until the button is pushed  
again.  
The power-on indicator turns  
to green when the system  
power is on.  
2
3
Power-on indicator or system  
state indicator or power button  
for system board 2  
System identification indicator  
or button for system board 1  
The identification button can  
be used to locate a particular  
system and system board  
within a chassis. When the  
button is pushed, the blue  
status indicator of the system  
on the front and rear blinks  
until the button is pushed  
again.  
The power-on indicator turns  
to amber when the system  
critical event occurs.  
4
5
Power-on indicator or system  
state indicator or power button  
for system board 1  
Hard drives  
Up to 24, hot-swappable, 2.5--  
inch hard drives.  
8
 
Item Indicator, button or  
connector  
Icon  
Description  
6
7
Drive cover  
This is not a usable drive slot.  
Power-on indicator or system  
state indicator or power button  
for system board 3  
NOTE: When turning on  
the system, the video  
monitor can take from  
several seconds to over  
two minutes to display an  
image, depending on the  
amount of DIMM installed  
in the system.  
NOTE: On ACPI-  
compliant operating  
systems (OSs), turning off  
the system by using the  
power button causes the  
system to perform a  
graceful shutdown before  
the system is turned off.  
NOTE: To force an  
ungraceful shutdown,  
press and hold the power  
button for five seconds.  
8
System identification indicator  
or button for system board 3  
The identification button can  
be used to locate a particular  
system and system board  
within a chassis. When the  
button is pushed, the blue  
status indicator of the system  
on the front and rear blinks  
until the button is pushed  
again.  
The power button controls the  
DC power supply unit (PSU)  
output to the system.  
9
Power-on indicator or system  
state indicator or power button  
for system board 4  
10  
System identification indicator  
or button for system board 4  
The identification button can  
be used to locate a particular  
system and system board  
within a chassis. When the  
button is pushed, the blue  
status indicator of the system  
on the front and rear blinks  
until the button is pushed  
again.  
9
Hard drive indicator patterns  
Figure 2. Hard drive front view  
1.  
hard drive status indicator (green and amber) 2.  
hard drive activity indicator (green)  
Table 2. Hard drive indicator patterns  
Controller  
Hard drive type  
Function  
Activity LED  
Green  
Status LED  
Green  
Onboard  
Controller  
SATA2  
Drive on-line  
Fail  
Off/Blinking when On  
active  
Off  
On  
Back panel features and indicators  
Figure 3. Back panel features and indicators  
10  
   
Table 3. Back panel features and indicators  
Item Indicator, button, or  
connector  
Icon  
Description  
1
PSU 2  
1600 W AC PSUs.  
1600 W AC PSUs.  
2
3
PSU 1  
USB port  
Enables you to connect USB  
devices to the system. The  
ports are USB 3.0-compliant.  
4
5
6
7
Ethernet connector  
Ethernet connector  
Management port  
USB to serial port  
VGA port  
10G NIC 1 connector.  
10G NIC 2 connector.  
Dedicated management port.  
Connects the system to a host.  
8
Connects a VGA display to the  
system.  
The power-on indicator glows  
green when the system power  
is on.  
9
Power button/power and  
system LED  
The power-on indicator turns  
amber when the system critical  
event occurs.  
The power button controls the  
DC PSU output to the system.  
NOTE: When turning on  
the system, the video  
monitor can take from  
several seconds to over  
two minutes to display an  
image, on the basis of the  
disk space available in the  
system.  
NOTE: On ACPI-  
compliant operating  
systems, turning off the  
system by using the  
power button causes the  
system to perform a  
graceful shutdown before  
the system is turned off.  
11  
Item Indicator, button, or  
connector  
Icon  
Description  
NOTE: To force an  
ungraceful shutdown,  
press and hold the power  
button for five seconds.  
10  
System identification indicator  
The management software of  
both the systems and the  
identification buttons on the  
front can cause the indicator  
to flash blue to identify a  
particular system and system  
board. Indicators turn amber  
when the system requires  
attention because of an issue.  
System-board assembly configurations  
Figure 4. Enumeration four system boards for 1U node  
LAN indicator codes  
Figure 5. LAN indicators  
1.  
activity indicator  
2.  
link and network speed indicator  
12  
   
Table 4. LAN indicator codes  
Component  
Indicator  
Condition  
Link and network speed indicator  
Solid amber  
Solid green  
Blinking green  
Linking at 1 Gbps speed  
Linking at 10 Gbps speed  
Activity is present:  
Activity indicator  
Pre OS POST  
OS without driver  
OS with driver  
Blinking at speed relative to  
packet density.  
Off  
No link/activity present  
D0 (uninitialized)  
D3 (cold)  
S4 (hibernation)  
Figure 6. LAN indicators (management port)  
1.  
speed indicator  
2.  
link and activity indicator  
Table 5. LAN indicators (management port)  
Component  
Indicator  
Condition  
Speed indicator  
Solid green  
Solid amber  
Off  
Linking at 1 Gbps speed  
Linking at 10/100 Mbps speed  
No access or Idle  
Link and activity indicator  
Blinking green  
LAN access or Link up  
13  
Power and system board indicator codes  
The LEDs on the system front panel and back panel display status codes during system startup. For  
location of the LEDs on the front panel, see the Front panel features and indicators section. For location  
of the LEDs on the back panel, see the Back panel features and indicators section.  
Table 6. Status indicator codes  
Component  
Indicator  
Green  
Condition  
Power-on indicator (A  
bicolor LED on power  
button)  
Solid  
Off  
Power On (S0)  
Amber  
Green  
Off  
iDRAC critical condition event in Power Off mode  
(S4/S5)  
Amber  
Blinking  
Off  
Green  
iDRAC critical condition event in Power On mode  
(S0)  
Amber  
Blinking  
System identification  
indicator  
Steady blue  
IPMI using Chassis Identify Command On or ID  
Button Press ID On  
Blinking blue  
Off  
Only IPMI using Chassis Identify Command Blink  
On  
IPMI using Chassis Identify Command Off or ID  
Button Press ID Off  
14  
 
Power Supply Unit indicator codes  
Each AC power supply unit (PSU) has an illuminated translucent handle that indicates whether power is  
present or whether a power fault has occurred.  
1600 W AC/1600 W HVDC PSU  
Figure 7. PSU status indicator  
1.  
PSU  
2.  
AC power indicator  
Table 7. 1600 W AC/1600 W HVDC PSU indicators  
Component  
Indicator  
Condition  
Standby mode with Fan Lock for  
15 seconds.  
AC power indicator  
Solid amber  
Standby mode with OTP range  
Active mode with +12 V DC Fault  
Active mode with Fan Lock for 15  
seconds.  
Solid green  
Blinking green  
Off  
DC_OK (power good)  
Standby mode normal  
Unit without AC power  
15  
   
iDRAC heart beat LED  
The system board provides iDRAC heart beat LED (CR17) for iDRAC debugs. The iDRAC heart beat LED is  
green. When the system AC power is connected, the LED glows. When iDRAC firmware is ready, the  
iDRAC heart beat LED blinks.  
Figure 8. iDRAC heart beat LED on the Dell XC6320 system board  
1.  
iDRAC heart beat LED  
Documentation references  
For information about the Dell documents, see the Support Matrix specific for your product.  
For information about the Nutanix documents that applies to a specific release of Nutanix solution  
software, see the Support Matrix specific for your product.  
16  
   
2
Performing initial system configuration  
After you receive your system, you must set up your system, install the operating system if it is not pre-  
installed, and set up and configure the system iDRAC IP address.  
Setting up your system  
1. Unpack the system.  
2. Install the system into the rack. For more information about installing the system into the rack, see  
your system Rack Installation Placemat.  
3. Connect the peripheral devices to the system.  
4. Connect the system to its electrical outlet.  
5. Turn on the system by pressing the power button or by using iDRAC.  
6. Turn on the attached peripheral devices.  
Setting up and configuring the iDRAC IP address  
You can set up the Integrated Dell Remote Access Controller (iDRAC) IP address by using one of the  
following interfaces:  
Dell iDRAC Settings utility  
Dell Lifecycle Controller  
Dell OpenManage Deployment Toolkit  
You can use the default iDRAC IP address 192.168.0.120 to configure the initial network settings,  
including setting up DHCP or a static IP for iDRAC.  
You can configure iDRAC IP address by using the following interfaces:  
NOTE: Ensure that you change the default user name and password after setting up the iDRAC IP  
address.  
iDRAC Web interface: For more information, see the Integrated Dell Remote Access Controller User's  
Guide.  
Remote Access Controller ADMin (RACADM): For more information, see the RACADM Command Line  
Interface Reference Guide and the Integrated Dell Remote Access Controller User's Guide.  
Remote Services that include Web Services Management (WS-Man): For more information, see the  
Dell Lifecycle Controller Remote Services Quick Start Guide.  
For more information about setting up and configuring iDRAC, see the Integrated Dell Remote Access  
Controller User's Guide available at Dell.com/esmmanuals.  
17  
     
Logging in to iDRAC  
You can log in to iDRAC as an iDRAC local user, a Microsoft Active Directory user, or a Lightweight  
Directory Access Protocol (LDAP) user. You can also log in by using Single Sign-On or a Smart Card. The  
default user name is rootand password is calvin. For more information about logging in to iDRAC and  
iDRAC licenses, see the Integrated Dell Remote Access Controller User's Guide available at Dell.com/  
idracmanuals.  
You can also access iDRAC by using RACADM. For more information, see the RACADM Command Line  
Interface Reference Guide and the Integrated Dell Remote Access Controller User's Guide available at  
Dell.com/idracmanuals.  
Methods of installing the operating system  
If the system is shipped without an operating system, install the supported OS on the system by using one  
of the following methods:  
Dell Systems Management Tools and Documentation media — see the operating system  
documentation available at Dell.com/operatingsystemmanuals.  
Dell Lifecycle Controller — see the Dell Lifecycle Controller documentation available at Dell.com/  
idracmanuals.  
Dell OpenManage Deployment Toolkit — see the Dell OpenManage documentation available at  
Dell.com/openmanagemanuals OpenManage software.  
For information about supported operating systems, see the operating systems support matrix available at  
Dell.com/ossupport.  
Managing your system remotely  
To perform out-of-band systems management by using iDRAC, configure iDRAC for remote accessibility,  
set up the management station and managed system, and configure the supported web browsers. For  
more information, see the Integrated Dell Remote Access Controller User’s Guide at Dell.com/  
idracmanuals.  
You can also remotely monitor and manage the server by using the Dell OpenManage Server  
Administrator (OMSA) software and OpenManage Essentials (OME) systems management console. For  
more information, see Dell.com/openmanagemanuals OpenManage Server Administrator or  
Dell.com/openmanagemanuals OpenManage Essentials.  
Downloading drivers and firmware  
Dell recommends you to download and install the latest BIOS, drivers, and systems management  
firmware on your system.  
Ensure that you clear the web browser cache.  
1. Go to Dell.com/support/drivers.  
2. In the Identify your product section, enter the Service Tag of your system in Enter a Service Tag or  
Express Service Code.  
18  
       
NOTE: If you do not have the Service Tag, you can do one of the following:  
Select Auto-detect your product to allow the system to automatically detect your Service  
Tag  
Select Browse for a product to select your product from the Select a product page.  
3. Click Drivers and downloads.  
The drivers that are applicable to your selection are displayed.  
4. Repeat steps 1 through 3 to download the HDD zoning configuration utility.  
5. Search on the basis of Category, and then click System Utilities.  
HDD zoning configuration utility is displayed.  
19  
3
Pre-operating system management  
applications  
You can manage basic settings and features of a system without booting to the operating system by  
using the system firmware.  
Navigation keys  
The navigation keys can help you access the pre-operating system management applications.  
Page Up  
Moves to the previous screen.  
Moves to the next screen.  
Moves to the previous field.  
Moves to the next field.  
Page Down  
Up arrow  
Down arrow  
Enter  
Enables you to type a value in the selected field (if applicable) or follow the link in  
the field.  
Spacebar  
Tab  
Expands or collapses a drop-down list, if applicable.  
Moves to the next focus area.  
NOTE: This feature is applicable for the standard graphical browser only.  
Esc  
Moves to the previous page until you view the main screen. Pressing Esc in the  
main screen exits System BIOS/iDRAC Settings/Device Settings/Service Tag  
Settings and proceeds with system boot.  
F1  
Displays the System Setup help information.  
Enables you to enter System Setup.  
Enables you to enter Lifecycle Controller.  
Enables you to enter Boot Manager.  
Enables you to enter PXE boot.  
F2  
F10  
F11  
F12  
System Setup  
By using the System Setup screen, you can configure the BIOS settings, iDRAC settings, and device  
settings of your system.  
These settings have already been preconfigured per solution requirements. Contact Dell before you  
change these settings.  
20  
     
NOTE: Help text for the selected field is displayed in the graphical browser by default. To view the  
help text in the text browser, press F1.  
You can access system setup by using two methods:  
Standard graphical browser—The browser is enabled by default.  
Text browser—The browser is enabled by using Console Redirection.  
Entering System Setup  
1. Turn on, or restart your system.  
2. Press F2 immediately after you see the following message:  
F2 = System Setup  
If your operating system begins to load before you press F2, wait for the system to finish booting,  
and then restart your system and try again.  
System Setup details  
The System Setup Main Menu screen details are explained as follows:  
System BIOS  
Enables you to configure BIOS settings.  
Enables you to configure iDRAC settings.  
iDRAC Settings  
The iDRAC settings utility is an interface to set up and configure the iDRAC  
parameters by using UEFI (Unified Extensible Firmware Interface). You can enable  
or disable various iDRAC parameters by using the iDRAC settings utility. For more  
information about this utility, see Integrated Dell Remote Access Controller User’s  
Guide at Dell.com/idracmanuals.  
Device Settings  
Enables you to configure device settings.  
System BIOS Settings details  
The System BIOS Settings screen details are explained as follows:  
System  
Specifies information about the system such as the system model name, BIOS  
Information  
version, and Service Tag.  
Memory Settings  
Specifies information and options related to the installed memory.  
Processor Settings Specifies information and options related to the processor such as speed and  
cache size.  
SATA Settings  
Boot Settings  
Specifies options to enable or disable the integrated SATA controller and ports.  
Specifies options to specify the boot mode (BIOS or UEFI). Enables you to modify  
UEFI and BIOS boot settings.  
Network Settings Specifies options to change the network settings.  
Integrated  
Devices  
Specifies options to manage integrated device controllers and ports and specify  
related features and options.  
21  
     
Serial  
Communication  
Specifies options to manage the serial ports and specify related features and  
options.  
System Profile  
Settings  
Specifies options to change the processor power management settings, memory  
frequency, and so on.  
System Security  
Specifies options to configure the system security settings, such as system  
password, setup password, Trusted Platform Module (TPM) security. It also  
manages the power and NMI buttons on the system.  
Miscellaneous  
Settings  
Specifies options to change the system date, time, and so on.  
System Information details  
The System Information screen details are explained as follows:  
System Model  
Name  
Specifies the system model name.  
System BIOS  
Version  
Specifies the BIOS version installed on the system.  
Specifies the current version of the Management Engine firmware.  
System  
Management  
Engine Version  
System Service  
Tag  
Specifies the system Service Tag.  
System  
Manufacturer  
Specifies the name of the system manufacturer.  
Specifies the contact information of the system manufacturer.  
System  
Manufacturer  
Contact  
Information  
System CPLD  
Version  
Specifies the current version of the system complex programmable logic device  
(CPLD) firmware.  
UEFI Compliance Specifies the UEFI compliance level of the system firmware.  
Version  
Memory Settings details  
The Memory Settings screen details are explained as follows:  
System Memory  
Size  
Specifies the memory size in the system.  
Specifies the type of memory installed in the system.  
Specifies the system memory speed.  
System Memory  
Type  
System Memory  
Speed  
System Memory  
Voltage  
Specifies the system memory voltage.  
Specifies the amount of video memory.  
Video Memory  
22  
   
System Memory  
Testing  
Specifies whether the system memory tests are run during system boot. Options  
are Enabled and Disabled. This option is set to Disabled by default.  
Memory  
Operating Mode  
Specifies the memory operating mode. The options available are Optimizer Mode,  
Advanced ECC Mode, Mirror Mode, Spare Mode, Spare with Advanced ECC Mode,  
Dell Fault Resilient Mode and Dell NUMA Fault Resilient Mode. This option is set  
to Optimizer Mode by default.  
NOTE: The Memory Operating Mode option can have different default and  
available options based on the memory configuration of your system.  
NOTE: The Dell Fault Resilient Mode option establishes an area of memory  
that is fault resilient. This mode can be used by an operating system that  
supports the feature to load critical applications or enables the operating  
system kernel to maximize system availability.  
Node Interleaving Specifies if Non-Uniform Memory architecture (NUMA) is supported. If this field is  
set to Enabled, memory interleaving is supported if a symmetric memory  
configuration is installed. If the field is set to Disabled, the system supports NUMA  
(asymmetric) memory configurations. This option is set to Disabled by default.  
Snoop Mode  
Specifies the Snoop Mode options. The Snoop Mode options available are Home  
Snoop, Early Snoop, and Cluster on Die. This option is set to Early Snoop by  
default. This field is available only when the Node Interleaving is set to Disabled.  
Processor Settings details  
The Processor Settings screen details are explained as follows:  
Logical Processor Enables or disables the logical processors and displays the number of logical  
processors. If this option is set to Enabled, the BIOS displays all the logical  
processors. If this option is set to Disabled, the BIOS displays only one logical  
processor per core. This option is set to Enabled by default.  
QPI Speed  
Enables you to control QuickPath Interconnect data rate settings.  
Alternate RTID  
(Requestor  
Transaction ID)  
Setting  
Modifies Requestor Transaction IDs, which are QPI resources. This option is set to  
Disabled by default.  
NOTE: Enabling this option may negatively impact the overall system  
performance.  
Virtualization  
Technology  
Enables or disables the additional hardware capabilities provided for virtualization.  
This option is set to Enabled by default.  
Address  
Translation  
Service (ATS)  
Defines the Address Translation Cache (ATC) for devices to cache the DMA  
transactions. This option provides an interface between CPU and DMA Memory  
Management to a chipset's Address Translation and Protection Table to translate  
DMA addresses to host addresses. This option is set to Enabled by default.  
Adjacent Cache  
Line Prefetch  
Optimizes the system for applications that need high utilization of sequential  
memory access. This option is set to Enabled by default. You can disable this  
option for applications that need high utilization of random memory access.  
Hardware  
Prefetcher  
Enables or disables the hardware prefetcher. This option is set to Enabled by  
default.  
DCU Streamer  
Prefetcher  
Enables or disables the Data Cache Unit (DCU) streamer prefetcher. This option is  
set to Enabled by default.  
23  
 
DCU IP Prefetcher Enables or disables the Data Cache Unit (DCU) IP prefetcher. This option is set to  
Enabled by default.  
Execute Disable  
Enables you to run the disable memory protection technology. This option is set to  
Enabled by default.  
Logical Processor Enables you to improve the energy efficiency of a system. It uses the operating  
Idling  
system core parking algorithm and parks some of the logical processors in the  
system which in turn allows the corresponding processor cores to transition into a  
lower power idle state. This option can only be enabled if the operating system  
supports it. It is set to Disabled by default.  
Configurable TDP Enables you to reconfigure the processor Thermal Design Power (TDP) levels  
during POST based on the power and thermal delivery capabilities of the system.  
TDP verifies the maximum heat the cooling system is needed to dissipate. This  
option is set to Nominal by default.  
NOTE: This option is only available on certain stock keeping units (SKUs) of the  
processors.  
X2Apic Mode  
Enables or disables the X2Apic mode.  
Dell Controlled  
Turbo  
Controls the turbo engagement. Enable this option only when System Profile is set  
to Performance.  
NOTE: Depending on the number of installed CPUs, there may be up to four  
processor listings.  
Number of Cores Controls the number of enabled cores in each processor. This option is set to All  
per Processor  
by default.  
Processor 64-bit  
Support  
Specifies if the processor(s) support 64-bit extensions.  
Processor Core  
Speed  
Specifies the maximum core frequency of the processor.  
Processor 1  
NOTE: Depending on the number of CPUs, there may be up to four  
processors listed.  
The following settings are displayed for each processor installed in the system:  
Family-Model-  
Stepping  
Specifies the family, model, and stepping of the processor  
as defined by Intel.  
Brand  
Specifies the brand name.  
Specifies the total L2 cache.  
Specifies the total L3 cache.  
Level 2 Cache  
Level 3 Cache  
Number of Cores Specifies the number of cores per processor.  
SATA Settings details  
The SATA Settings screen details are explained as follows:  
Embedded SATA  
Enables the embedded SATA option to be set to Off, ATA, AHCI, or RAID modes.  
This option is set to AHCI by default.  
24  
 
Security Freeze  
Lock  
Sends Security Freeze Lock command to the Embedded SATA drives during POST.  
This option is applicable only for ATA and AHCI modes.  
Write Cache  
Port A  
Enables or disables the command for Embedded SATA drives during POST.  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Model  
Specifies the drive model of the selected device.  
Specifies the type of drive attached to the SATA port.  
Drive Type  
Capacity  
Specifies the total capacity of the hard drive. This field is  
undefined for removable media devices such as optical  
drives.  
Port B  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Model  
Specifies the drive model of the selected device.  
Specifies the type of drive attached to the SATA port.  
Drive Type  
Capacity  
Specifies the total capacity of the hard drive. This field is  
undefined for removable media devices such as optical  
drives.  
Port C  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Model  
Specifies the drive model of the selected device.  
Specifies the type of drive attached to the SATA port.  
Drive Type  
Capacity  
Specifies the total capacity of the hard drive. This field is  
undefined for removable media devices such as optical  
drives.  
Port D  
Port E  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
25  
Port F  
Port G  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Model  
Specifies the drive model of the selected device.  
Specifies the type of drive attached to the SATA port.  
Drive Type  
Capacity  
Specifies the total capacity of the hard drive. This field is  
undefined for removable media devices such as optical  
drives.  
Port H  
Port I  
Port J  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Model  
Specifies the drive model of the selected device.  
Specifies the type of drive attached to the SATA port.  
Drive Type  
Capacity  
Specifies the total capacity of the hard drive. This field is  
undefined for removable media devices such as optical  
drives.  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Model  
Specifies the drive model of the selected device.  
Specifies the type of drive attached to the SATA port.  
Drive Type  
Capacity  
Specifies the total capacity of the hard drive. This field is  
undefined for removable media devices such as optical  
drives.  
Sets the drive type of the selected device. For Embedded SATA settings in ATA  
mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS  
support.  
For AHCI or RAID mode, BIOS support is always enabled.  
Model  
Specifies the drive model of the selected device.  
Specifies the type of drive attached to the SATA port.  
Drive Type  
26  
Capacity  
Specifies the total capacity of the hard drive. This field is  
undefined for removable media devices such as optical  
drives.  
Boot Settings details  
The Boot Settings screen details are explained as follows:  
Boot Mode  
Enables you to set the boot mode of the system.  
CAUTION: Switching the boot mode may prevent the system from booting if  
the operating system is not installed in the same boot mode.  
If the operating system supports UEFI, you can set this option to UEFI. Setting this  
field to BIOS allows compatibility with non-UEFI operating systems. This option is  
set to BIOS by default.  
NOTE: Setting this field to UEFI disables the BIOS Boot Settings menu. Setting  
this field to BIOS disables the UEFI Boot Settings menu.  
Boot Sequence  
Retry  
Enables or disables the Boot Sequence Retry feature. If this option is set to Enabled  
and the system fails to boot, the system reattempts the boot sequence after 30  
seconds. This option is set to Enabled by default.  
Hard-Disk Failover Specifies the hard drive that is booted in the event of a hard drive failure. The  
devices are selected in the Hard-Disk Drive Sequence on the Boot Option Setting  
menu. When this option is set to Disabled, only the first hard drive in the list is  
attempted to boot. When this option is set to Enabled, all hard drives are attempted  
to boot in the order selected in the Hard-Disk Drive Sequence. This option is not  
enabled for UEFI Boot Mode.  
Boot Option  
Settings  
Configures the boot sequence and the boot devices.  
BIOS Boot  
Settings  
Enables or disables BIOS boot options.  
NOTE: This option is enabled only if the boot mode is BIOS.  
UEFI Boot Settings Enables or disables UEFI Boot options. The Boot options include IPv4 PXE and IPv6  
PXE. This option is set to IPv4 by default.  
NOTE: This option is enabled only if the boot mode is UEFI.  
Network Settings screen details  
The Network Settings screen details are explained as follows:  
PXE Device n (n = Enables or disables the device. When enabled, a UEFI boot option is created for the  
1 to 4)  
device.  
PXE Device n  
Settings (n = 1 to  
4)  
Enables you to control the configuration of the PXE device.  
Integrated Devices details  
The Integrated Devices screen details are explained as follows:  
27  
     
USB 3.0 Setting  
Enables or disables the USB 3.0 support. Enable this option only if your operating  
system supports USB 3.0. If you disable this option, devices operate at USB 2.0  
speed. USB 3.0 is enabled by default.  
User Accessible  
USB Ports  
Enables or disables the USB ports. Selecting Only Back Ports On disables the front  
USB ports, selecting All Ports Off disables all USB ports. The USB keyboard and  
mouse operate during boot process in certain operating systems. After the boot  
process is complete, the USB keyboard and mouse do not work if the ports are  
disabled.  
NOTE: Selecting Only Back Ports On and All Ports Off disables the USB  
management port and also restricts access to iDRAC features.  
Internal USB Port Enables or disables the internal USB port. This option is set to Enabled by default.  
Integrated RAID  
Controller  
Enables or disables the integrated RAID controller. This option is set to Enabled by  
default.  
Integrated  
Enables or disables the integrated network card.  
Network Card 1  
Embedded NIC1  
and NIC2  
NOTE: The Embedded NIC1 and NIC2 options are only available on systems  
that do not have Integrated Network Card 1.  
Enables or disables the Embedded NIC1 and NIC2 options. If set to Disabled, the  
NIC may still be available for shared network access by the embedded  
management controller. The embedded NIC1 and NIC2 options are only available  
on systems that do not have Network Daughter Cards (NDCs). The Embedded NIC1  
and NIC2 option is mutually exclusive with the Integrated Network Card 1 option.  
Configure the Embedded NIC1 and NIC2 option by using the NIC management  
utilities of the system.  
I/OAT DMA Engine Enables or disables the I/OAT option. Enable only if the hardware and software  
support the feature.  
Embedded Video Enables or disables the Embedded Video Controller option. This option is set to  
Controller  
Enabled by default.  
Current State of  
Displays the current state of the embedded video controller. The Current State of  
Embedded Video Embedded Video Controller option is a read-only field. If the Embedded Video  
Controller  
Controller is the only display capability in the system (that is, no add-in graphics  
card is installed), then the Embedded Video Controller is automatically used as the  
primary display even if the Embedded Video Controller setting is set to Disabled.  
SR-IOV Global  
Enable  
Enables or disables the BIOS configuration of Single Root I/O Virtualization (SR-  
IOV) devices. This option is set to Enabled by default.  
OS Watchdog  
Timer  
If your system stops responding, this watchdog timer aids in the recovery of your  
operating system. When this option is set to Enabled, the operating system  
initializes the timer. When this option is set to Disabled (the default), the timer does  
not have any effect on the system.  
Memory Mapped  
I/O above 4 GB  
Enables or disables the support for PCIe devices that need large amounts of  
memory. This option is set to Enabled by default.  
Slot Disablement Enables or disables the available PCIe slots on your system. The slot disablement  
feature controls the configuration of PCIe cards installed in the specified slot. Slots  
must be disabled only when the installed peripheral card prevents booting into the  
operating system or causes delays in system startup. If the slot is disabled, both the  
Option ROM and UEFI drivers are disabled.  
28  
Serial Communication details  
The Serial Communication screen details are explained as follows:  
Serial  
Communication  
Selects serial communication devices (Serial Device 1 and Serial Device 2) in BIOS.  
BIOS console redirection can also be enabled and the port address can be  
specified. This option is set to Auto by default.  
Serial Port  
Address  
Enables you to set the port address for serial devices. This option is set to Serial  
Device 1=COM2, Serial Device 2=COM1 by default.  
NOTE: You can use only Serial Device 2 for the Serial Over LAN (SOL) feature.  
To use console redirection by SOL, configure the same port address for  
console redirection and the serial device.  
NOTE: Every time the system boots, the BIOS syncs the serial MUX setting  
saved in iDRAC. The serial MUX setting can independently be changed in  
iDRAC. Loading the BIOS default settings from within the BIOS setup utility  
may not always revert the serial MUX setting to the default setting of Serial  
Device 1.  
External Serial  
Connector  
Enables you to associate the External Serial Connector to Serial Device 1, Serial  
Device 2, or the Remote Access Device by using this option.  
NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use  
console redirection by SOL, configure the same port address for console  
redirection and the serial device.  
NOTE: Every time the system boots, the BIOS syncs the serial MUX setting  
saved in iDRAC. The serial MUX setting can independently be changed in  
iDRAC. Loading the BIOS default settings from within the BIOS setup utility  
may not always revert this setting to the default setting of Serial Device 1.  
Failsafe Baud Rate Specifies the failsafe baud rate for console redirection. The BIOS attempts to  
determine the baud rate automatically. This failsafe baud rate is used only if the  
attempt fails, and the value must not be changed. This option is set to 115200by  
default.  
Remote Terminal Sets the remote console terminal type. This option is set to VT 100/VT 220by  
Type  
default.  
Redirection After Enables or disables the BIOS console redirection when the operating system is  
Boot loaded. This option is set to Enabled by default.  
System Profile Settings details  
The System Profile Settings screen details are explained as follows:  
System Profile  
Sets the system profile. If you set the System Profile option to a mode other than  
Custom, the BIOS automatically sets the rest of the options. You can only change  
the rest of the options if the mode is set to Custom. This option is set to  
Performance Per Watt Optimized (DAPC) by default. DAPC is Dell Active Power  
Controller.  
NOTE: All the parameters on the system profile setting screen are available  
only when the System Profile option is set to Custom.  
29  
   
CPU Power  
Sets the CPU power management. This option is set to System DBPM (DAPC) by  
Management  
default. DBPM is Demand-Based Power Management.  
Memory  
Sets the speed of the system memory. You can select Maximum Performance,  
Frequency  
Maximum Reliability, or a specific speed.  
Turbo Boost  
Enables or disables the processor to operate in the turbo boost mode. This option  
is set to Enabled by default.  
Energy Efficient  
Turbo  
Enables or disables the Energy Efficient Turbo option.  
Energy Efficient Turbo (EET) is a mode of operation where a processor’s core  
frequency is adjusted to be within the turbo range based on workload.  
C1E  
Enables or disables the processor to switch to a minimum performance state when  
it is idle. This option is set to Enabled by default.  
C States  
Enables or disables the processor to operate in all available power states. This  
option is set to Enabled by default.  
Collaborative CPU Enables or disables the CPU power management option. When set to Enabled, the  
Performance  
Control  
CPU power management is controlled by the OS DBPM and the System DBPM  
(DAPC). This option is set to Disabled by default.  
Memory Patrol  
Scrub  
Sets the memory patrol scrub frequency. This option is set to Standard by default.  
Memory Refresh  
Rate  
Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.  
Uncore Frequency Enables you to select the Processor Uncore Frequency option.  
Dynamic mode enables the processor to optimize power resources across the  
cores and uncore during runtime. The optimization of the uncore frequency to  
either save power or optimize performance is influenced by the setting of the  
Energy Efficiency Policy option.  
Energy Efficient  
Policy  
Enables you to select the Energy Efficient Policy option.  
The CPU uses the setting to manipulate the internal behavior of the processor and  
determines whether to target higher performance or better power savings.  
Number of Turbo  
Boot Enabled  
Cores for  
NOTE: If there are two processors installed in the system, you see an entry for  
Number of Turbo Boost Enabled Cores for Processor 2.  
Processor 1  
Controls the number of turbo boost enabled cores for processor 1. The maximum  
number of cores is enabled by default.  
Monitor/Mwait  
Enables the Monitor/Mwait instructions in the processor. This option is set to  
Enabled for all system profiles, except Custom by default.  
NOTE: This option can be disabled only if the C States option in the Custom  
mode is set to disabled.  
NOTE: When C States is set to Enabled in the Custom mode, changing the  
Monitor/Mwait setting does not impact the system power or performance.  
System Security Settings details  
The System Security Settings screen details are explained as follows:  
30  
 
Intel AES-NI  
Improves the speed of applications by performing encryption and decryption by  
using the Advanced Encryption Standard Instruction Set (AES-NI). This option is set  
to Enabled by default.  
System Password Sets the system password. This option is set to Enabled by default and is read-only  
if the password jumper is not installed in the system.  
Setup Password  
Sets the setup password. This option is read-only if the password jumper is not  
installed in the system.  
Password Status  
TPM Security  
Locks the system password. This option is set to Unlocked by default.  
NOTE: The TPM menu is available only when the TPM module is installed.  
Enables you to control the reporting mode of the TPM. The TPM Security option is  
set to Off by default. You can only modify the TPM Status, TPM Activation, and Intel  
TXT fields if the TPM Status field is set to either On with Pre-boot Measurements  
or On without Pre-boot Measurements.  
TPM Information Changes the operational state of the TPM. This option is set to No Change by  
default.  
TPM Status  
Specifies the TPM status.  
TPM Command  
CAUTION: Clearing the TPM results in the loss of all keys in the TPM. The  
loss of TPM keys may affect booting to the operating system.  
Clears all the contents of the TPM. The TPM Clear option is set to No by default.  
Intel TXT  
Enables or disables the Intel Trusted Execution Technology (TXT) option. To enable  
the Intel TXT option, virtualization technology and TPM Security must be enabled  
with Pre-boot measurements. This option is set to Off by default.  
Power Button  
NMI Button  
Enables or disables the power button on the front of the system. This option is set  
to Enabled by default.  
Enables or disables the NMI button on the front of the system. This option is set to  
Disabled by default.  
AC Power  
Recovery  
Sets how the system behaves after AC power is restored to the system. This option  
is set to Last by default.  
AC Power  
Sets the time delay for the system to power up after AC power is restored to the  
Recovery Delay  
system. This option is set to Immediate by default.  
User Defined  
Delay (60s to  
240s)  
Sets the User Defined Delay option when the User Defined option for AC Power  
Recovery Delay is selected.  
UEFI Variable  
Access  
Provides varying degrees of securing UEFI variables. When set to Standard (the  
default), UEFI variables are accessible in the operating system per the UEFI  
specification. When set to Controlled, selected UEFI variables are protected in the  
environment and new UEFI boot entries are forced to be at the end of the current  
boot order.  
Secure Boot  
Enables Secure Boot, where the BIOS authenticates each pre-boot image by using  
the certificates in the Secure Boot Policy. Secure Boot is disabled by default.  
Secure Boot  
Policy  
When Secure Boot policy is set to Standard, the BIOS uses the system  
manufacturer’s key and certificates to authenticate pre-boot images. When Secure  
Boot policy is set to Custom, the BIOS uses the user-defined key and certificates.  
Secure Boot policy is set to Standard by default.  
31  
Secure Boot  
Policy Summary  
Specifies the list of certificates and hashes that secure boot uses to authenticate  
images.  
Miscellaneous Settings details  
The Miscellaneous Settings screen details are explained as follows:  
System Time  
System Date  
Asset Tag  
Enables you to set the time on the system.  
Enables you to set the date on the system.  
Specifies the asset tag and enables you to modify it for security and tracking  
purposes.  
Keyboard  
NumLock  
Enables you to set whether the system boots with the NumLock enabled or  
disabled. This option is set to On by default.  
NOTE: This option does not apply to 84-key keyboards.  
F1/F2 Prompt on  
Error  
Enables or disables the F1/F2 prompt on error. This option is set to Enabled by  
default. The F1/F2 prompt also includes keyboard errors.  
Load Legacy  
Video Option  
ROM  
Enables you to determine whether the system BIOS loads the legacy video (INT  
10H) option ROM from the video controller. Selecting Enabled in the operating  
system does not support UEFI video output standards. This field is available only for  
UEFI boot mode. You cannot set the option to Enabled if UEFI Secure Boot mode  
is enabled.  
In-System  
Enables or disables In-System Characterization. This option is set to Disabled by  
Characterization  
default. The two other options are Enabled and Enabled - No Reboot.  
NOTE: The default setting for In-System Characterization is subject to change  
in future BIOS releases.  
When enabled, In-System Characterization (ISC) executes during POST upon  
detecting relevant change(s) in system configuration to optimize system power and  
performance. ISC takes about 20 seconds to execute, and system reset is needed  
for ISC results to be applied. The Enabled - No Reboot option executes ISC and  
continues without applying ISC results until the next time system reset occurs. The  
Enabled option executes ISC and forces an immediate system reset so that ISC  
results can be applied. It takes the system longer to be ready due to the forced  
system reset. When disabled, ISC does not execute.  
System setup options at boot  
F2  
Initiate Setup during POST  
Alt+F  
Load optimal default properties in Setup menu.  
32  
   
About Boot Manager  
Boot manager enables you to add, delete, and arrange boot options. You can also access System Setup  
and boot options without restarting the system.  
Viewing Boot Manager  
To enter Boot Manager:  
1. Turn on, or restart your system.  
2. Press F11 when you see the following message:  
F11 = Boot Manager  
If your operating system begins to load before you press F11, allow the system to complete the  
booting, and then restart your system and try again.  
Boot Manager main menu  
Continue Normal The system attempts to boot to devices starting with the first item in the boot  
Boot  
order. If the boot attempt fails, the system continues with the next item in the boot  
order until the boot is successful or no more boot options are found.  
One Shot Boot  
Menu  
Displays the boot menu where you can select a one time boot device to boot from.  
Launch System  
Setup  
Allows you to access the System Setup.  
Launch Lifecycle  
Controller  
Closes the Boot Manager and invokes the Dell Lifecycle Controller program.  
Opens system utilities menu such as system diagnostics and UEFI shell.  
System Utilities  
Changing the boot order  
You may have to change the boot order if you want to boot from a USB key or an optical drive. The  
following instructions may vary if you have selected BIOS for Boot Mode.  
1. On the System Setup Main Menu screen, click System BIOS Boot Settings.  
2. Click Boot Option Settings Boot Sequence.  
3. Use the arrow keys to select a boot device, and use the plus (+) and minus (-) sign keys to move the  
device down or up in the order.  
4. Click Exit, and then click Yes to save the settings on exit.  
Choosing the system boot mode  
System Setup enables you to specify one of the following boot modes for installing your operating  
system:  
BIOS boot mode (the default) is the standard BIOS-level boot interface.  
Unified Extensible Firmware Interface (UEFI) boot mode is an enhanced 64-bit boot interface. If you  
have configured your system to boot to UEFI mode, it replaces the system BIOS.  
33  
         
1. From the System Setup Main Menu, click Boot Settings, and select Boot Mode.  
2. Select the boot mode you want the system to boot into.  
CAUTION: Switching the boot mode may prevent the system from booting if the operating  
system is not installed in the same boot mode.  
3. After the system boots in the specified boot mode, proceed to install your operating system from  
that mode.  
NOTE: Operating systems must be UEFI-compatible to be installed from the UEFI boot mode. DOS  
and 32-bit operating systems do not support UEFI and can only be installed from the BIOS boot  
mode.  
NOTE: For the latest information about supported operating systems, go to Dell.com/ossupport.  
Assigning a system and setup password  
NOTE: The password jumper enables or disables the System Password and Setup Password  
features. For more information about the password jumper settings, see Dell XC6320 system board  
You can assign a new System Password and Setup Password or change an existing System Password  
and Setup Password only when the password jumper setting is Enabled and Password Status is  
Unlocked. If the password jumper setting is disabled, the existing System Password and Setup Password  
are deleted and you need not provide the system password to boot the system.  
1. To enter System Setup, press F2 immediately after a power-on or reboot.  
2. From the System Setup Main Menu, select System BIOS and press Enter.  
3. On the System BIOS screen, select System Security and press Enter.  
4. On the System Security screen, ensure that password status is unlocked.  
5. Select System Password, enter your system password, and press Enter or Tab.  
Use the following guidelines to assign the system password:  
A password can have up to 32 characters.  
The password can contain the numbers 0 through 9.  
Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).  
A message prompts you to re-enter the system password.  
6. Re-enter the system password, and then click OK.  
7. Select Setup Password, enter your system password and press Enter or Tab.  
A message prompts you to re-enter the setup password.  
8. Re-enter the setup password, and click OK.  
9. Press Esc to return to the System BIOS screen. Press Esc.  
A message prompts you to save the changes.  
NOTE: Password protection does not take effect until the system reboots.  
34  
 
Deleting or changing system and setup password  
NOTE: You cannot delete or change an existing system or setup password if the Password Status is  
set to Locked.  
1. To enter System Setup, press F2 immediately after turning on or restarting your system.  
2. On the System Setup Main Menu screen, click System BIOS System Security.  
3. On the System Security screen, ensure that Password Status is set to Unlocked.  
4. In the System Password field, alter or delete the existing system password, and then press Enter or  
Tab.  
5. In the Setup Password field, alter or delete the existing setup password, and then press Enter or Tab.  
If you change the system and setup password, a message prompts you to reenter the new password.  
If you delete the system and setup password, a message prompts you to confirm the deletion.  
6. Press Esc to return to the System BIOS screen. Press Esc again, and a message prompts you to save  
the changes.  
35  
 
4
Installing and removing system  
components  
Safety instructions  
WARNING: Whenever you lift the system, get others to assist you. To avoid injury, do not attempt  
to lift the system by yourself.  
WARNING: Working on systems that are still connected to a PSU can be dangerous.  
CAUTION: This system must be operated with the system cover installed to ensure proper  
cooling.  
CAUTION: System components and electronic circuit boards can be damaged by discharge of  
static electricity.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
To avoid injury to yourself or damage to the system, follow these guidelines:  
Always disconnect the system from the power outlet whenever you are working inside the system.  
If possible, wear a grounded wrist strap as you work inside the system. Or discharge any static  
electricity by touching the bare metal chassis of system case, or the bare metal body of any other  
grounded appliance.  
Hold electronic circuit boards by the edges only. Do not touch the components on the board unless it  
is necessary to do so. Do not flex or stress the circuit board.  
Leave all components inside the static-proof packaging until you are ready to use the component for  
the installation.  
Recommended tools  
#1 Phillips screwdriver  
#2 Phillips screwdriver  
Torx #T20 screwdriver  
36  
     
Opening and closing the system  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Removing the system cover  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
1. Remove the securing screw from the system cover.  
2. Press the cover release latch lock.  
3. Hold the system cover on both the sides with your palm on the traction pad, and slide out the system  
cover.  
4. Lift the cover away from the system.  
Figure 9. Opening and closing the system  
1. system cover  
3. traction pad  
2. securing screw  
4. cover release latch lock  
Install the system cover.  
37  
   
Installing the system cover  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Place the system cover on the chassis and slide it to the front of the chassis until it snaps into place.  
2. Secure the cover with the securing screw.  
1. Reconnect the system to the electrical outlet.  
2. Turn on the system, including any attached peripherals.  
Inside the system  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
CAUTION: This system must be operated with the system cover installed to ensure proper  
cooling.  
Cooling fans  
Servers use a lot of power to function, and that in turn generates a lot of heat. That heat, without a  
system in place to dissipate it, can destroy the mechanical parts and damage the server. In most cases,  
the simplest and most efficient way to dissipate this heat is through the use of fans.  
Removing a cooling fan  
WARNING: Do not attempt to operate the system without the cooling fans.  
WARNING: The cooling fan can continue to spin for some time after the system has been  
powered down. Allow time for the fan to stop spinning before removing it from the system.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
NOTE: Observe the routing of the cable through the cable tie as you remove them from the system.  
You must route these cables properly when you replace them to prevent the cables from being  
pinched or crimped.  
1. Follow the safety guidelines listed in the Safety instructions section.  
38  
       
2. Follow the procedure listed in the Before working inside your system section.  
1. Disconnect the fan’s power cable from the power distribution board 1.  
2. Lift the cooling fan cage out of the chassis.  
Figure 10. Removing and installing a cooling fan cage  
1. locking clips (2)  
3. power connector  
2. cooling fan cage  
4. locating pin (6)  
3. Disconnect the fan cable from the fan connector on the cooling fan cage.  
4. Lift the cooling fan with the sponge out of the cooling fan cage.  
39  
Figure 11. Removing and installing a cooling fan  
1. cooling fan 1  
3. cooling fan 3  
5. cooling fan 4  
7. cooling fan cage  
2. cooling fan 2  
4. sponge  
6. fan cable  
Related Links  
Installing a cooling fan  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Align the cooling fan with the sponge and slide it in the cooling-fan cage until the cooling fan is  
firmly seated.  
40  
 
NOTE: The fan blades should face the control panel of the system.  
2. Connect the fan cable to the connector on the cooling-fan cage.  
3. Align the cooling-fan cage with the locating pins on the chassis and place it into the chassis until it is  
firmly seated in place.  
4. Connect the fan’s power cable to the connector on the power distribution board 1.  
You must route these cables properly through the ties to prevent them from being pinched or  
crimped.  
1. Follow the procedure listed in the After working inside your system section.  
2. Check the management software to see if the fan is rotating at the optimal speed.  
Related Links  
Hard drives  
A hard drive is a data storage device used for storing and retrieving digital information by using one or  
more rigid rapidly rotating disks (platters) coated with magnetic material.  
CAUTION: Use only hard drives that have been tested and approved for use with the SAS/SATA  
backplane.  
The following are the recommended guidelines for installing a mix of SAS hard drives, SATA hard drives,  
and SSDs:  
Only two drive types can be mixed per node.  
Drives 0 and 1 must be of same type.  
The remaining drives must all be the same type.  
SAS hard drive support is based on the add-on card and the onboard configuration supports SATA  
hard drive only.  
Removing a 2.5-inch hard drive blank  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
CAUTION: To maintain proper system cooling, all empty hard drive bays must have drive blanks  
installed.  
NOTE: This section is applicable to systems with hot swappable hard drives only.  
Follow the safety guidelines listed in the Safety instructions section.  
Pull the handle to remove the 2.5-inch hard drive blank out of the hard drive bay.  
41  
   
Figure 12. Removing or installing a 2.5-inch hard drive blank  
1. handle  
2. latch  
3. 2.5-inch hard drive blank  
Installing a 2.5-inch hard drive blank  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. With the latch facing up, slide the latch into the hard drive bay.  
2. Push the 2.5-inch hard drive with a slight inclination into the hard drive bay until the hard drive blank  
is seated in place.  
Removing a hard drive  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
CAUTION: To maintain proper system cooling, all empty hard drive bays must have drive blanks  
installed.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Turn the lock lever counterclockwise until it points to the unlock symbol.  
2. Slide the release button to open the release handle.  
3. Using the release handle, pull the hard drive carrier out of the hard drive bay.  
42  
   
Figure 13. Removing and installing a hard drive  
1. lock lever  
2. hard driver carrier  
3. hard drive slot  
Installing a hard drive  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
CAUTION: To maintain proper system cooling, all empty hard drive bays must have drive blanks  
installed.  
43  
 
Follow the safety guidelines listed in the Safety instructions section.  
1. With the lever on the hard drive carrier open, slide the hard drive carrier into the drive bay until the  
hard drive connector engages with the backplane.  
2. Close the release handle to lock the hard drive in place.  
3. Turn the lock lever clockwise to the lock symbol.  
1. To check the status of the hard drive, see the hard drive activity and status indicators. For more  
information, see the Hard drive indicator patterns section.  
2. Check the management software to verify the status of the installed hard drive.  
Removing a hard drive from a hard drive carrier  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
CAUTION: When installing a hard drive carrier, ensure that the adjacent drives are fully installed.  
Inserting a hard drive carrier and attempting to lock its handle next to a partially installed carrier  
can damage the partially installed carrier's shield spring and make it unusable.  
CAUTION: To prevent data loss, ensure that your operating system supports hot-swappable drive  
installation. See the documentation supplied with the operating system.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Remove the screws.  
2. Lift the hard drive out of the hard drive carrier.  
44  
 
Figure 14. Removing and installing a hard drive from the hard drive carrier  
1. hard drive carrier  
3. hard drive  
2. screw (4)  
Installing a hard drive into a hard drive carrier  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Place the hard drive into the hard drive carrier.  
2. Secure the hard drive to the hard drive carrier with screws.  
SATADOM  
Important information about SATADOM  
The SATA DiskOnMotherboard (SATADOM) shipped with XC Series appliances is intended as an  
appliance boot device.  
45  
     
NOTE: Write intensive activities and processes leveraged by XC appliances, are intended to take  
place on the SSDs and HDDs and not the boot device.  
The hypervisor boot device is not intended for application use.  
WARNING: Adding additional write intensive software to the SATADOM boot disk results in heavy  
wear on the device beyond design specifications resulting in premature hardware failure.  
You should not run applications on the hypervisor operating system.  
Examples of write intensive applications  
Following are the examples of write intensive applications:  
System Center Agents.  
System Center Configuration Manager (CCMExec.exe).  
System Center Operations Manager (MonitoringHost.exe).  
Writeintensive Agents.  
Databases.  
Disk management utilities (third-party disk defragmentation or partitioning tools).  
Additional roles outside of the appliance’s intended use (web server, domain controller, RDS, and so  
on.).  
Clientbased Antivirus.  
Run Virtual Machines directly on the SATADOM. Ensure that the Virtual Machines run on Solid State  
Drives (SSDs) and Hard Disk Drives (HDDs).  
Removing the SATADOM  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
1. Disconnect the power cable from the SATADOM and the system board.  
2. Using a screwdriver, press the metal latch to release the SATADOM.  
3. Holding the SATADOM by its edges, pull the SATADOM until the card edge connector disengages  
from the onboard SATA connector 5 on the system board.  
46  
 
Figure 15. Removing the SATADOM  
1. SATADOM  
2. SATA connector SATA5  
3. power cable  
4. system board power connector  
Installing the SATADOM  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Holding the SATADOM by its edges, position it so that the card edge connector aligns with the  
onboard SATA connector 5 on the system board.  
2. Press the SATADOM with your thumbs until it is fully seated.  
3. Reconnect all the cables.  
1. Reconnect the peripherals and connect the system to the electrical outlet.  
2. Turn on the system, including any attached peripherals.  
47  
 
Cable routing for SATADOM and LSI 2008  
Figure 16. Cable Routing for SATADOM and LSI 2008  
Table 8. Cable Routing for SATADOM and LSI 2008  
Item  
Cable  
From (LSI 2008 SAS Mezzanine  
Card)  
To (System Board)  
1
LSI 2008 SAS  
Mezzanine card  
Mini-SAS connector 4-7 (J4)  
SAS/SATA connectors 4 and 5  
2
Mini-SAS cable  
On LSI 2008 SAS Mezzanine Card  
SATADOM  
power cable  
SATADOM  
HDD Power Connector on the  
system board  
3
4
On LSI 2008 SAS Mezzanine Card  
Mini-SAS HD Connector 0-3  
Mini-SAS  
connector 0-3  
(J3)  
5
System board  
Power supply units  
NOTE: Configurations higher than indicated in the table may change the PSU mode to non-  
redundant. In non-redundant mode if the power requirement exceeds the installed system power  
capacity, the BIOS will throttle the processors. Also, since Processor Power Capping is enabled,  
processor throttling occurs on configurations that exceed the cap value.  
NOTE: Both the PSUs are hot swappable, and they can support hot swap in any condition if the  
system has power throttling feature.  
The following table lists the maximum supported configuration where power supply unit (PSU)  
redundancy is guaranteed:  
48  
   
Table 9. PSUs configuration  
PSU  
System boards  
1600 W  
Up to two 120 W processor per system board, six hard drivesper system board, and 16  
memory modulesper system board  
Removing a power supply unit  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
CAUTION: The system requires at least one power supply unit (PSU) to operate normally.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the power cable from the power source and the PSU, and disconnect the peripherals.  
Press the release lever and by using the handle, slide the PSU out of the system.  
NOTE: Removing the PSU may require considerable force.  
Figure 17. Removing and installing a PSU  
1. fan  
2. PSU  
49  
 
3. PSU connector  
4. handle  
Installing a power supply unit  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
CAUTION: The system requires at least one power supply unit (PSU) to operate normally.  
Verify that both PSUs are of the same type and have the same maximum output power.  
NOTE: The maximum output power is printed on the PSU label.  
Follow the safety guidelines listed in the Safety instructions section.  
Slide the new PSU into the chassis until the PSU until is fully seated and the release lever snaps into  
place.  
Connect the power cable to the PSU and plug the cable into a power outlet.  
NOTE: When installing a new PSU in a system with two PSUs, allow several seconds for the system  
to recognize the PSU and determine its status.  
System board assembly  
Removing the system board tray  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Remove the screw that secures the retaining latch.  
2. Press the retaining latch and slide the system board tray out of the chassis.  
50  
     
Figure 18. Removing and installing a system board tray  
1. retaining latch  
2. screw  
3. system board tray  
Installing the system board tray  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Slide the system board tray into the chassis until it snaps into place.  
2. Replace the screw that secures the retaining latch.  
Removing the system board assembly  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
51  
   
4. Disconnect all the external cables from the system board.  
1. Remove the screw that secures the retaining latch.  
2. Press the retaining latch and by using the handle, slide the system board assembly out of the chassis.  
Figure 19. Removing and installing a system board assembly  
1. retaining latch  
2. screw  
3. system board assembly  
Installing the system board assembly  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Slide the system board assembly into the chassis until it snaps into place.  
2. Replace the screw that secures the retaining latch.  
1. Reconnect all the external cables to the system board.  
2. Reconnect the peripherals and connect the system to the electrical outlet.  
3. Turn on the system, including any attached peripherals.  
NOTE: To add the service tag of the system board to match the service tag of the physical  
node, contact technical support.  
52  
 
Air baffle  
Removing the cooling shroud  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
4. Remove the system board assembly.  
Press the four latches along the direction of the arrows, and then lift the cooling shroud out of the  
system board assembly.  
Figure 20. Removing the cooling shroud  
1. cooling shroud  
2. CPU 1 heatsink  
Related Links  
53  
   
Installing the cooling shroud  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
Replace the cooling shroud into the system board assembly. Make sure that the four latches are  
properly engaged with the heat sink bases and the latches click in place.  
NOTE: When installing the cooling shroud, make sure the arrow of the mark on the cooling  
shroud points to processor 1, and keep the flat surface of the cooling shroud horizontal.  
Figure 21. Top view of the installed cooling shroud  
1. Install the system board assembly.  
2. Reconnect the peripherals and connect the system to the electrical outlet.  
3. Turn on the system, including any attached peripherals.  
Related Links  
Heat sinks  
The heat sink transfers heat away form the processor as the processor is unable to dissipate sufficient  
heat to moderate this temperature. The heat sink is designed to maximize its surface area in contact with  
the cooling medium surrounding it, such as the air. Thermal grease improve the heat sink's performance  
by filling air gaps between the heat sink and the heat spreader on the processor.  
54  
   
Removing the heat sink  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
NOTE: Place the foolproof pins of two processor heat sinks facing inside.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
4. Remove the system board assembly.  
WARNING: The heat sink may be hot to touch for some time after the system has been  
powered down. Allow the heat sink to cool before removing it.  
CAUTION: Never remove the heat sink from a processor unless you intend to remove the  
processor. The heat sink is necessary to maintain proper thermal conditions.  
1. Using a Phillips screwdriver, loosen one of the heat sink retention screws.  
Wait for 30 seconds for the heat sink to loosen from the processor.  
2. Remove the other heat sink retention screws.  
3. Lift the heat sink off the processor and set the heat sink aside with thermal grease side facing up.  
Figure 22. Removing and installing the heat sink  
1. heat sink  
2. captive screws (4)  
4. slot (4)  
3. processor socket  
Related Links  
55  
 
Installing the heat sink  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Using a clean lint-free cloth, remove the thermal grease from the heat sink.  
2. Apply new thermal grease evenly to the center of the top of the new processor.  
CAUTION: Using excess thermal grease can cause grease to contact the processor shield,  
which can cause contamination of the processor socket.  
3. Place the heat sink on the processor.  
4. Using a Phillips screwdriver, tighten the heat sink retention screws.  
Replace the system board assembly.  
Related Links  
Processors  
This system board supports Intel E5-2600 v3 processor series, which is up to 145 W, 3.5 GHz, and 12  
cores based on Intel Wellsburg PCH chipset.  
Removing a processor  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Remove the system board assembly.  
3. Remove the heat sink.  
CAUTION: The processor is held in its socket under strong pressure. The release lever can  
spring up suddenly if not firmly grasped.  
1. Position your thumbs firmly over the processor socket release levers and release the levers from the  
locked position. Rotate the levers 90 degrees upward until the processor is released from the socket.  
2. Rotate the processor shield upward and out of the way.  
3. Lift the processor out of the socket and leave the socket release levers up so that the socket is ready  
for the new processor.  
CAUTION: Be careful not to bend any of the pins on the CPU socket when removing the  
processor. Bending the pins can permanently damage the system board. Be sure to properly  
align the process or notch to the socket and insert straight down. Do not move from side to  
side.  
56  
     
Figure 23. Removing and installing a processor  
1. socket release lever  
3. processor  
2. orientation arrow  
4. notch in processor (4)  
6. socket release lever (2)  
8. notch  
5. processor shield  
7. socket pin array  
Related Links  
Installing a processor  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
NOTE: When installing only one processor, the processor must be installed in the processor 0 (for  
the socket location, see the System board connectors section).  
NOTE: If you are upgrading your processors, prior to upgrading your system, download and install  
the latest system BIOS version from Dell.com/support/home. Follow the instructions included in  
the file download to install the update on your system.  
57  
 
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Unpack the processor if it has not been used previously.  
NOTE: If the processor has already been used, remove any thermal grease from the top of the  
processor by using a lint-free cloth.  
3. Remove the system board assembly.  
1. Align the processor with the socket keys on the CPU socket.  
CAUTION: Positioning the processor incorrectly can permanently damage the system board  
or the processor. Be careful not to bend the pins in the CPU socket.  
2. With the release lever on the processor socket in the open position, align the processor with the  
socket keys and set the processor lightly in the socket.  
CAUTION: Do not use force to seat the processor. When the processor is positioned  
correctly, it engages easily into the socket.  
3. Close the processor shield.  
4. Rotate the socket release lever down until it snaps into place.  
5. Using a clean lint-free cloth, remove the thermal grease from the heat sink.  
6. Apply thermal grease evenly to the center of the top of the new processor.  
CAUTION: Using excess thermal grease can cause grease to contact the processor shield,  
which can cause contamination of the processor socket.  
7. Place the heat sink on the processor.  
8. Using a Phillips screwdriver, tighten the heat sink retention screws.  
1. Replace the system board assembly.  
2. Reconnect the system to its electrical outlet and turn on the system, including any attached  
peripheral devices.  
3. Press F2 to enter the System Setup program, and check that the processor information matches the  
new system configuration. See the System setup options at boot section.  
Related Links  
Expansion card assembly and expansion card  
The expansion card in computer is a printed circuit board that can be inserted into an expansion slot on  
the computer system board riser card to add functionality to the computer system through the expansion  
bus.  
NOTE: A missing or an unsupported expansion card riser logs an SEL event. It does not prevent your  
system from powering on and no BIOS POST message or F1/F2 pause is displayed.  
Removing the expansion card  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
58  
   
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
4. Remove the system board assembly.  
1. Remove the screws that secure the expansion card assembly.  
2. Lift the expansion card assembly out of the system board assembly.  
Figure 24. Removing the expansion card assembly for 1U node  
1. expansion card assembly  
3. system board assembly  
2. screw (4)  
3. Remove the screw that secures the expansion card.  
4. Hold the expansion card by its edges, and carefully remove it from the riser card.  
NOTE: If you are removing the card permanently, install an expansion card slot cover over the  
empty expansion slot opening, and close the expansion card latch.  
NOTE: You must install a filler bracket over an empty expansion slot to maintain Federal  
Communications Commission (FCC) certification of the system. The brackets also keep dust  
and dirt out of the system and aid in proper cooling and airflow inside the system.  
59  
Figure 25. Removing the expansion card for 1U node  
1. expansion card slot cover  
3. expansion card  
2. screw  
Related Links  
Installing the expansion card  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
CAUTION: Expansion cards can only be installed in the slots on the expansion card riser. Do not  
attempt to install expansion cards directly into the riser connector on the system board.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Unpack the expansion card and prepare it for installation. For instructions, see the documentation  
accompanying the card.  
1. Remove the screws that secure the expansion card assembly.  
2. Lift the expansion card assembly away from the system board assembly.  
3. Remove the screw that secures the filler bracket.  
4. Hold the filler bracket by its edges, and carefully remove it from the riser card.  
NOTE: Retain this bracket in case you need to remove the expansion card. Filler brackets must  
be installed over empty expansion cards slots to maintain FCC certification of the system. The  
brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside  
the system.  
5. Holding the card by its edges, position the card so that the card edge connector aligns with the riser  
card on the riser card.  
60  
 
6. Insert the card edge connector firmly into the riser card until the card is fully seated.  
7. Replace the screw that secures the expansion card.  
8. Place the expansion card assembly into the system board assembly.  
9. Install the screws that secure the expansion card assembly.  
1. Install the system board assembly.  
2. Reconnect the peripherals and connect the system to the electrical outlet.  
3. Turn on the system, including any attached peripherals.  
Related Links  
Riser card  
Figure 26. 1U riser card for 1U node  
1.  
PCI-E Gen 3 x16  
2.  
micro SD card socket  
Removing the riser card  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
4. Remove the system board assembly.  
5. Remove the expansion card.  
1. Remove the screws that secure the riser card to the expansion card bracket.  
2. Pull the riser card away from the expansion card bracket.  
61  
   
Figure 27. Removing and installing the riser card  
1. expansion card bracket  
3. riser card  
2. screw (2)  
Related Links  
Installing the riser card  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Place the riser card into the expansion card bracket.  
2. Replace the screws that secure the riser card to the expansion card bracket.  
1. Install the expansion card.  
2. Install the system board assembly.  
3. Reconnect the peripherals and connect the system to the electrical outlet.  
4. Turn on the system, including any attached peripherals.  
Related Links  
LSI 2008 Mezzanine Card  
62  
   
Removing the LSI 2008 SAS mezzanine card  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
NOTE: The LSI 2008 SAS mezzanine card is seated in PCI-E Gen3 x8 mezzanine slot 3 on the  
system board, which is not active in 1-processor configuration.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
4. Remove the system board assembly.  
1. Disconnect all the cables from the mezzanine card.  
2. Remove the screws that secure the LSI 2008 SAS mezzanine card.  
3. Lift the mezzanine card out of the system-board assembly.  
Figure 28. Removing and installing the LSI 2008 SAS mezzanine card  
1. LSI 2008 SAS mezzanine card  
3. bridge card  
2. screw (3)  
63  
 
Installing the LSI 2008 SAS mezzanine card  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Place the LSI 2008 SAS mezzanine card on the system board assembly.  
2. Install the screws that secure the LSI 2008 SAS mezzanine card.  
3. Reconnect all the cables to the LSI 2008 SAS mezzanine card.  
1. Install the system board assembly.  
2. Reconnect the peripherals and connect the system to the electrical outlet.  
3. Turn on the system, including any attached peripherals.  
Related Links  
Mezzanine card bridge board  
Removing the mezzanine card bridge board  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
4. Remove the system board assembly.  
5. Remove the mezzanine card.  
Pull the mezzanine card bridge board away from the mezzanine slot on the system board.  
64  
     
Figure 29. Removing and installing the mezzanine card bridge board  
1. PCI slot 2. mezzanine card bridge  
Related Links  
Installing the mezzanine card bridge board  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
Install the mezzanine card bridge board into the mezzanine slot on the system board.  
1. Install the mezzanine card.  
2. Install the system board assembly.  
3. Reconnect the peripherals and connect the system to the electrical outlet.  
4. Turn on the system, including any attached peripherals.  
Related Links  
System memory  
System memory holds the instructions that the processor executes. Each system board has sixteen DDR4  
memory module sockets for the installation of up to sixteen registered DDR4-2400 MHz (2400 MHz at 2  
memory modules per channel) memory modules to support processor 1 and processor 2. For the  
location of the memory modules, see the C6320 system board connectors section.  
65  
   
Memory slot features  
Support 8 channels, 16 DDR4 registered DIMMs (RDIMMs)  
Speed up to 2400 MT/s  
Max. capacities:  
512 GB with 32 GB RDIMM  
Supports DDR4  
Supports Error Correction Code (ECC)  
NOTE: Linux operating system does not support the S4 (hibernation) mode.  
Supported memory module configuration  
For the sequence of the 16 memory-module sockets, the system requires at least one memory module  
installed on processor 1’s DIMM slot 1 in order to boot up. When you insert the memory modules, always  
start with CHA_A1. The optimized memory module installation sequence is 1, 2, 3, 4, 5, 6, 7, and 8.  
Figure 30. DIMM slot locations  
Table 10. Memory module configurations for dual processors  
Processor 1  
Memory  
modules  
CHA  
CHB  
CHC  
CHD  
A1  
A5  
A2  
A6  
A3  
A7  
A4  
A8  
2
66  
   
Processor 1  
6
8
12  
16  
Table 11. Memory module configurations for dual processors  
Processor 2  
Memory  
modules  
CHA  
CHB  
CHC  
CHD  
B1  
B5  
B2  
B6  
B3  
B7  
B4  
B8  
2
6
8
12  
16  
Removing the memory modules  
WARNING: The memory modules are hot to the touch for some time after the system has been  
powered down. Allow time for the memory modules to cool before handling them. Handle the  
memory modules by the card edges and avoid touching the components on the memory module.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
4. Remove the system board assembly.  
5. Remove the cooling shroud.  
1. Locate the memory module sockets.  
CAUTION: Handle each memory module only on either card edge, ensuring not to touch the  
middle of the memory module. To avoid damaging components on the memory module,  
remove only one memory module at a time.  
2. Simultaneously press down and out on the ejectors at both ends of the memory module socket until  
the memory module is released from the socket.  
3. Lift the memory module out of the socket by holding the memory module only by its edges.  
67  
 
Figure 31. Removing a memory module  
1. memory module  
2. alignment key  
3. memory module socket ejector (2)  
Related Links  
Installing the memory modules  
WARNING: The memory modules are hot to the touch for some time after the system has been  
powered down. Allow time for the memory modules to cool before handling them. Handle the  
memory modules by the card edges and avoid touching the components on the memory module.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Follow the safety guidelines listed in the Safety instructions section.  
1. Press down and out on the ejectors on each end of the memory module socket.  
2. Align the memory module correctly with the alignment key of the memory module socket.  
3. Press down firmly on the memory module with your thumbs until the module snaps into place.  
CAUTION: Even pressure during insertion must be applied at both ends of the module  
simultaneously to prevent damage to the socket. No pressure should be applied to the center  
of the module.  
4. Complete the latching of the module into the socket by applying inward pressure to the socket  
ejectors to ensure that the ejectors are in a locked position. When the memory module is properly  
seated in the socket, the ejectors on the memory module socket align with the ejectors on other  
identical sockets that have memory modules installed.  
68  
 
Figure 32. Installing a memory module  
1. memory module  
2. alignment key  
3. memory module socket ejector (2)  
1. Install the cooling shroud.  
2. Install the system board assembly.  
3. Press F2 to enter System Setup, and check the System Memory setting.  
4. If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure  
that the memory modules are firmly seated in the sockets.  
5. Run the system memory test in the system diagnostics.  
Related Links  
System battery  
Replacing the system battery  
WARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the  
battery only with the same or equivalent type recommended by the manufacturer. See your  
safety information for additional information.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
69  
   
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and peripherals.  
4. Remove the system board assembly.  
5. Remove the cooling shroud.  
6. Remove the expansion card assembly.  
1. Push the battery latch and lift the battery out of the connector.  
CAUTION: To avoid damage to the battery connector, you must firmly support the connector  
while installing or removing a battery.  
2. Hold the new battery with the "+" facing the positive side of battery connector.  
3. Insert the battery into the battery holder until it is seated in place.  
Figure 33. Replacing the system battery  
1. battery socket  
2. battery  
1. Replace the system board assembly.  
2. Reconnect the system to the electrical outlet.  
3. Turn on the system, including any attached peripherals.  
4. Enter System Setup to confirm that the battery is operating properly. See the System setup section.  
5. In System Setup, enter correct time and date in the Time and Date fields.  
6. Exit System Setup.  
Related Links  
70  
System board  
Removing a system board  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Follow the safety guidelines listed in the Safety instructions section.  
2. Turn off the system, including any attached peripherals.  
3. Disconnect the system from the electrical outlet and disconnect the peripherals.  
4. Remove the system board assembly.  
5. Remove the cooling shroud.  
6. Remove the expansion card assembly.  
7. Remove the heat sinks.  
8. Remove the memory modules.  
9. If installed, remove the SAS mezzanine card, 1 GbE mezzanine card, or 10 GbE mezzanine card.  
10. Disconnect all the cables from the system board.  
1. Remove the screws that secure the system board to the system board assembly and then slide the  
system board.  
CAUTION: Do not lift the system board by holding a memory module, processor, or other  
components.  
2. Hold the system board by the edges and lift the system board away from the system board assembly.  
71  
   
Figure 34. Removing and installing the system board  
1. system board assembly  
3. screw (8)  
2. system board  
Related Links  
Installing a system board  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
72  
 
Follow the safety guidelines listed in the Safety instructions section.  
1. Holding the system board by the edges, slide the system board into the system board assembly.  
2. Install the screws to secure the system board to the system board assembly.  
1. Install the Trusted Platform Module (TPM). For information how to install the TPM, see the Installing  
the Trusted Platform Module section. For more information on the TPM, see the Trusted Platform  
Module section.  
NOTE: The TPM plug-in module is attached to the system board and cannot be removed. A  
replacement TPM plug-in module will be provided for all system board replacements where a  
TPM plug-in module was installed.  
2. Transfer the processors to the new system board.  
3. Remove the memory modules and transfer them to the same locations on the new board.  
4. Replace the heat sinks.  
5. Install the expansion card assembly.  
6. If applicable, install the SAS mezzanine card, 1 GbE mezzanine card, or 10 GbE mezzanine card.  
7. Connect all the cables to the system board.  
8. Install the cooling shroud.  
9. Follow the procedure listed in the After working inside your system section.  
10. Import your new or existing iDRAC Enterprise license. For more information, see Integrated Dell  
Remote Access Controller User's Guide, at Dell.com/esmmanuals.  
11. Ensure that you:  
a. Use the Easy Restore feature to restore the Service Tag. For more information, see the Easy  
restore section.  
b. If the Service Tag is not backed up in the backup flash device, enter the system Service Tag  
manually. For more information, see the Entering the system Service Tag section.  
c. Update the BIOS and iDRAC versions.  
d. Re-enable the Trusted Platform Module (TPM). For more information, see the Re-enabling the  
Trusted Platform Module (TPM) section.  
Related Links  
Entering the system Service Tag using System Setup  
1. If you know the system Service Tag, use the System Setup menu to enter the Service Tag.  
2. Turn on the system.  
3. To enter System Setup, press F2.  
4. Click Service Tag Settings.  
5. Enter the Service Tag.  
73  
 
NOTE: You can enter the Service Tag only when the Service Tag field is empty.  
6. Ensure that you enter the correct Service Tag. After entering the Service Tag, it cannot be updated or  
changed.  
7. Click OK.  
74  
5
Troubleshooting your system  
Safety first—for you and your system  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Minimum configuration to POST  
The three components mentioned below are the minimum configuration to POST:  
One power supply unit  
One Processor (CPU) in socket CPU1 (minimum for troubleshooting)  
One Memory Module (DIMM) installed in the socket A1  
NOTE: When PCI-E slot 1 and Mezzanine slot are to be used, processor 1 must be installed; when  
PCI-E slot 3 is to be used, both processor 1 and processor 2 must be installed.  
Safety first – for you and your system  
WARNING: Whenever you need to lift the system, get others to assist you. To avoid injury, do not  
attempt to lift the system by yourself.  
WARNING: Before removing the system cover, disconnect all power, then unplug the AC power  
cord, and then disconnect all peripheral devices, and all LAN lines.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Installation-related issues  
Perform the following checks when you troubleshoot installation issues:  
Check all cable and power connections (including all rack cable connections).  
Unplug the power cord and wait for one minute. Then reconnect the power cord and try again.  
If the network is reporting an error, verify that the system has enough memory and disk space.  
75  
         
Remove all added peripheral devices, one at a time, and try to turn on the system. If after removing a  
peripheral device, the system works, it may be an issue with the peripheral device or a configuration  
issue between the peripheral device and the system. Contact the peripheral device vendor for  
assistance.  
If the system does not turn on, check the LED display. If the power LED is not on, you may not be  
receiving AC power. Check the AC power cord to ensure that it is securely connected.  
Troubleshooting system startup failure  
If your system halts during startup, especially after installing an OS or reconfiguring your system’s  
hardware, check for invalid memory configurations. These could cause the system to halt at startup  
without any video output.  
For all other startup issues, note any system messages that are displayed on the screen. For more  
Troubleshooting external connections  
Ensure that all external cables are securely attached to the external connectors on your system before  
troubleshooting any external devices. See Front panel features and indicators and Back panel features  
Troubleshooting the video subsystem  
1. Check the system and power connections to the monitor.  
2. Check the video interface cabling from the system to the monitor.  
Troubleshooting a USB device  
To troubleshoot a USB keyboard and/or mouse for other USB devices, go to step 5. Use the following  
steps .  
1. Disconnect the keyboard and mouse cables from the system briefly and reconnect them.  
2. Connect the keyboard or mouse to the USB ports on the opposite side of the system.  
3. If the issue is resolved, restart the system, enter the System Setup program, and check if the  
nonfunctioning USB ports are enabled.  
4. Replace the keyboard or mouse with another working keyboard or mouse.  
If the issue is resolved, replace the faulty keyboard or mouse.  
If the issue is not resolved, proceed to the next step to begin troubleshooting the other USB devices  
attached to the system.  
5. Disable all the attached USB devices and disconnect them from the system.  
6. Restart the system and, if your keyboard is functioning, enter the system setup program. Ensure that  
all USB ports are enabled.  
If your keyboard is not functioning, you can also use remote access. If the system is not accessible,  
see Jumper settings for instructions on setting the NVRAM_CLR jumper inside your system and  
restoring the BIOS to the default settings.  
7. Reconnect and enable each USB device one at a time.  
8. If a device causes the same issue, turn off the device, replace the USB cable, and turn on the device.  
76  
       
If the issue persists, replace the device.  
If all troubleshooting fails, see Getting help.  
Troubleshooting a serial I/O device  
1. Turn off the system and any peripheral devices connected to the serial port.  
2. Swap the serial interface cable with another working cable, and turn on the system and the serial  
device.  
If the issue is resolved, replace the interface cable.  
3. Turn off the system and the serial device, and then swap the device with a comparable device.  
4. Turn on the system and the serial device.  
If the issue is resolved, replace the serial device.  
If the issue persists, see Getting help.  
Troubleshooting a NIC  
1. Restart the system and check for any system messages pertaining to the NIC controller.  
2. Check the appropriate indicator on the NIC connector. See LAN indicator codes.  
If the link indicator does not glow, check all cable connections.  
If the activity indicator does not glow, the network driver files might be damaged or missing.  
Remove and reinstall the drivers if applicable. See the NIC’s documentation.  
Change the auto-negotiation setting, if possible.  
Use another connector on the switch or hub.  
If you are using a NIC card instead of an integrated NIC, see the documentation for the NIC card.  
3. Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC’s  
documentation.  
4. Enter the System Setup program and confirm that the NIC ports are enabled. For more information,  
5. Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission  
speed. See the documentation for each network device.  
6. Ensure that all network cables are of the proper type and do not exceed the maximum length.  
If all troubleshooting fails, see Getting help.  
Troubleshooting a wet system  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Turn off the system and attached peripheral devices, and disconnect the system from the electrical  
outlet.  
2. Open the system.  
3. Disassemble components from the system.  
77  
     
Hard drives  
SAS backplane  
Expansion-card  
PSUs  
Fans  
Processors and heat sinks  
Memory modules  
4. Let the system dry thoroughly for minimum 24 hours.  
5. Reinstall the components you removed in step 3.  
6. Close the system.  
7. Reconnect the system to the electrical outlet, and turn on the system and attached peripheral  
devices.  
If the system does not start properly, see Getting help.  
8. If the system starts properly, turn off the system and reinstall the expansion card that you removed, if  
any.  
9. If the system fails to start, see Getting help.  
Troubleshooting a damaged system  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Turn off the system and attached peripheral devices, and disconnect the system from the electrical  
outlet.  
2. Open the system.  
3. Ensure that the following components are properly installed:  
Expansion-card assembly  
PSUs  
Fans  
Processors and heat sinks  
Memory modules  
hard drive carriers  
4. Ensure that all cables are properly connected.  
5. Close the system.  
6. If the system fails to start, see Getting help.  
Troubleshooting the system battery  
NOTE: If the system is turned off for long periods of time (for weeks or months), the NVRAM may  
lose its system configuration information. This situation is caused by a defective battery.  
1. Re-enter the time and date through the System Setup program. See System setup options at boot.  
2. Turn off the system and disconnect it from the electrical outlet for at least one hour.  
3. Reconnect the system to the electrical outlet and turn on the system.  
78  
   
4. Enter the System Setup program.  
If the date and time are not correct in the System Setup program, replace the battery.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or  
as directed by the online or telephone service and support team. Damage due to servicing  
that is not authorized by Dell is not covered by your warranty. Read and follow the safety  
instructions that are shipped with your product.  
If the problem is not resolved by replacing the battery, see Getting help.  
NOTE: Some software may cause the system time to speed up or slow down. If the system  
seems to operate normally except for the time kept in the System Setup program, the problem  
may be caused by software rather than by a defective battery.  
Troubleshooting PSUs  
1. Identify the faulty PSU by the PSU’s fault indicator. See Power and system board indicator codes.  
CAUTION: At least one PSU must be installed for the system to operate. Operating the system  
with only one PSU installed for extended period can cause the system to overheat.  
2. Reseat the PSU by removing and reinstalling it.  
NOTE: After installing a PSU, allow several seconds for the system to recognize the PSU and to  
determine if it is working properly. The power indicator glows green to signify that the PSU is  
functioning properly.  
If the issue persists, replace the faulty PSU.  
3. If all troubleshooting fails, see Getting help.  
Troubleshooting system cooling issues  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
Ensure that none of the following conditions exist:  
System cover, cooling shroud, drive blank, PSU blank, or front or back filler panel is removed.  
Ambient temperature is too high.  
External airflow is obstructed.  
Cables inside the system obstruct airflow.  
An individual cooling fan is removed or has failed.  
79  
   
Troubleshooting a fan  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Locate the faulty fan indicated by the diagnostic software.  
2. Turn off the system and all attached peripheral devices.  
3. Open the system.  
4. Reseat the fan’s power cable.  
5. Restart the system.  
If the fan functions properly, close the system.  
6. If the fan does not function, turn off the system and install a new fan.  
7. Restart the system.  
If the issue is resolved, close the system.  
8. If the replacement fan does not operate, see Getting help.  
Troubleshooting system memory  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
NOTE: Invalid memory configurations can cause your system to halt at startup without video  
output. See System memory, and verify that your memory configuration complies with all applicable  
guidelines.  
1. If the system is not operational, turn off the system and attached peripheral devices, and unplug the  
system from the power source. Wait at least 10 seconds and then reconnect the system to power.  
2. Turn on the system and attached peripheral devices and note the messages on the screen.  
Go to step 10 if an error message appears indicating a fault with a specific memory module.  
3. Enter the System Setup program and check the system memory settings. Make any changes to the  
memory settings, if needed.  
If the memory settings match the installed memory but a problem is still indicated, go to step 10.  
4. Turn off the system and attached peripheral devices, and disconnect the system from the electrical  
outlet.  
5. Remove the system-board assembly.  
6. Reseat the memory modules in their sockets.  
7. Install the system-board assembly.  
8. Reconnect the system to its electrical outlet, and turn on the system and attached peripheral devices.  
Enter the System Setup program and check the system memory settings.  
If the problem is not resolved, proceed with the next step.  
80  
   
9. Turn off the system and attached peripheral devices, and disconnect the system from the power  
source.  
10. Remove the system-board assembly.  
11. If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace  
the module.  
12. To troubleshoot an unspecified faulty memory module, replace the memory module in the first  
memory module socket with a module of the same type and capacity.  
13. Install the system-board assembly.  
14. Reconnect the system to its electrical outlet, and turn on the system and attached peripheral devices.  
15. As the system boots, observe any error message that appears and the diagnostic indicators on the  
front of the system.  
16. If the memory problem is still indicated, repeat step 10 through step 16 for each memory module  
installed.  
If the problem persists after all memory modules have been checked, see Getting help.  
Troubleshooting a hard drive  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. If your system has a RAID controller and your hard drives are configured in a RAID array, perform the  
following steps:  
a. Restart the system and enter the host adapter configuration utility program by pressing Ctrl+C for  
a LSI SAS 2008 mezzanine card.  
See the documentation supplied with the host adapter for information about the configuration  
utility.  
b. Ensure that the hard drive(s) have been configured correctly for the RAID array.  
c. Take the hard drive offline and reseat the drive.  
d. Exit the configuration utility and allow the system to boot to the operating system.  
2. Ensure that the required device drivers for your controller card are installed and are configured  
correctly. See the operating system documentation for more information.  
3. Restart the system, enter the System Setup program, and verify that the controller is enabled and the  
drives appear in the System Setup program.  
For more information, see Pre-operating system management applications.  
If the problem persists, see Getting help.  
Troubleshooting a storage controller  
NOTE: When troubleshooting a SAS RAID controller, also see the documentation for your operating  
system and the controller.  
1. Enter the System Setup program and ensure that the SAS controller is enabled. For more information,  
2. Restart the system and press the applicable key sequence to enter the configuration utility program.  
Ctrl+C for a LSI SAS 2008 mezzanine card  
81  
   
See the controller’s documentation for information about configuration settings.  
3. Check the configuration settings, make any necessary corrections, and restart the system.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or  
as directed by the online or telephone service and support team. Damage due to servicing  
that is not authorized by Dell is not covered by your warranty. Read and follow the safety  
instructions that are shipped with your product.  
4. Turn off the system and attached peripheral devices, and disconnect the system from its electrical  
outlet.  
5. Remove the system-board assembly.  
6. Ensure that the controller card is firmly seated into the system board connector.  
7. If you have a battery-cached SAS RAID controller, ensure that the RAID battery is properly connected  
and, if applicable, the memory module on the RAID card is properly seated.  
8. Ensure that the cables are firmly connected to the storage controller and the SAS backplane board.  
9. Install the system-board assembly.  
10. Reconnect the system to its electrical outlet, and turn on the system and attached peripheral devices.  
If the problem persists, see Getting help.  
Troubleshooting expansion cards  
NOTE: When troubleshooting an expansion card, see the documentation for your operating system  
and the expansion card.  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Turn off the system and attached peripheral devices, and disconnect the system from the electrical  
outlet.  
2. Remove the system-board assembly.  
3. Ensure that each expansion card is firmly seated in its connector.  
4. Install the system-board assembly.  
5. Reconnect the system to the electrical outlet, and turn on the system and attached peripheral  
devices.  
6. If the problem is not resolved, see Getting help.  
Troubleshooting processors  
CAUTION: Many repairs may only be done by a certified service technician. You should only  
perform troubleshooting and simple repairs as authorized in your product documentation, or as  
directed by the online or telephone service and support team. Damage due to servicing that is  
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions  
that are shipped with your product.  
1. Turn off the system and attached peripheral devices, and disconnect the system from the electrical  
outlet.  
2. Remove the system-board assembly.  
82  
   
3. Ensure that each processor and heat sink is properly installed.  
4. Install the system-board assembly.  
5. Reconnect the system to the electrical outlet, and turn on the system and attached peripheral  
devices.  
6. If the problem persists, turn off the system and attached peripheral devices, and disconnect the  
system from the electrical outlet.  
7. Remove the system-board assembly.  
8. Remove processor 2.  
9. Install the system-board assembly.  
10. Reconnect the system to the electrical outlet, and turn on the system and attached peripheral  
devices.  
If the problem persists, the processor is faulty. See Getting help.  
11. Turn off the system and attached peripheral devices, and disconnect the system from the electrical  
outlet.  
12. Remove the system-board assembly.  
13. Replace processor 1 with processor 2.  
14. Repeat step 9 through step 11.  
If you have tested both the processors and the problem persists, the system board is faulty. See  
IRQ assignment conflicts  
Most PCI devices can share an IRQ with another device, but they cannot use an IRQ simultaneously. To  
avoid this type of conflict, see the documentation for each PCI device for specific IRQ requirements.  
Table 12. Assignment specific IRQ requirements  
IRQ Line  
Assignment  
8254 timer  
IRQ0  
Keyboard controller  
IRQ1  
IRQ2  
IRQ3  
IRQ4  
IRQ5  
IRQ6  
IRQ7  
IRQ8  
IRQ9  
Cascade for IRQ9  
Serial port (COM2) or PCI_IRQ_POOL_DEFINITION  
Serial port (COM1) or PCI_IRQ_POOL_DEFINITION  
PCI_IRQ_POOL_DEFINITION  
PCI_IRQ_POOL_DEFINITION  
RESERVE  
RTC  
PCI_IRQ_POOL_DEFINITION  
83  
 
IRQ Line  
Assignment  
PCI_IRQ_POOL_DEFINITION  
IRQ10  
PCI_IRQ_POOL_DEFINITION  
Mouse controller  
IRQ11  
IRQ12  
IRQ13  
IRQ14  
IRQ15  
Processor  
Primary IDE controller  
Secondary IDE controller  
NOTE: PCI_IRQ_POOL_DEFINITION means BIOS code assigns at runtime.  
84  
6
Jumpers and connectors  
This topic provides specific information about the system jumpers. It also provides some basic  
information about jumpers and switches and describes the connectors on the various boards in the  
system. Jumpers on the system board help to disable system and setup passwords. You must know the  
connectors on the system board to install components and cables correctly.  
Dell XC6320 system board connectors  
Figure 35. Dell XC6320 system board connectors  
1.  
rear USB Connector 1  
2.  
PCI-E Gen3 x8 Mezzanine Slot 3 (Processor  
1)  
3.  
5.  
7.  
9.  
mini-SAS Connector 0-3  
onboard SATA Connector 4  
mini-SAS Connector 6-9  
DIMM sockets for processor 1  
4.  
6.  
8.  
HDD Power Connector  
onboard SATA Connector 5  
processor 1  
10. processor 2  
11. DIMM sockets for processor 2  
13. middle plane connector  
15. mini-SAS HD connector 0-3  
17. SAS/SATA connector 4  
12. main power connector  
14. SAS/SATA connector 5  
16. control panel connector  
18. PCIE_G3_X16 Slot 4 (Processor 2)  
20. SGPIO connector  
19. high-power connector  
21. DIMM sockets for processor 2  
22. DIMM sockets for processor 1  
24. TPM connector  
23. internal USB connector 2 (Left) and USB  
connector 3(Right)  
25. system battery  
26. PCI-E Gen3 x16 slot 1 (processor 1)  
28. UART connector  
27. CPLD debug connector  
85  
   
29. CPLD JTAG connector  
31. Power button  
30. PCI-E Gen3 x16 Slot 2 (processor 1)  
32. VGA port  
33. Internal TTL COM Connector  
35. LAN Management Connector  
37. LAN 2 LED  
34. USB to Serial Port  
36. Management Port  
38. LAN 2 Port  
39. LAN 1 LED  
40. LAN 1 Port  
41. UID LED  
Table 13. System board connectors  
Item  
Connector  
USB1  
Description  
1
Rear USB connector 1  
2
PCIE_G3_X8 (CPU1)  
PCI-E Gen3 x8 mezzanine slot 3 (processor  
1)  
3
miniSAS0-3  
Mini-SAS connector 0-3  
Hard drive power connector  
Onboard SATA connector 4  
Onboard SATA connector 5  
Mini-SAS connector 6-9  
Processor 1  
4
HDD POWER CON  
5
SATA4  
6
SATA5  
7
miniSAS6-9  
8
CPU1  
9
DIMM_A1, DIMM_A5, DIMM_A2, DIMM_A6  
DIMM sockets for processor 1  
Processor 2  
10  
11  
12  
13  
14  
15  
16  
17  
CPU2  
DIMM_B1, DIMM_B5, DIMM_B2, DIMM_B6  
DIMM sockets for processor 2  
SAS/SATA connector 5  
SAS/SATA connector 4  
Middle plane connector  
Mini-SAS HD connector 0-3  
High-power connector  
SATA5  
SATA4  
CONTROL_PANEL  
miniSAS0-3  
HI_PWR_CONN  
SGPIO  
Serial General Purpose Input/Output (SGPIO)  
connector  
18  
19  
20  
DIMM_B8, DIMM_B4, DIMM_B7, DIMM_B3  
DIMM_A8, DIMM_A4, DIMM_A7, DIMM_A3  
J106  
DIMM sockets for processor 2  
DIMM sockets for processor 1  
Internal USB connector 2 (left) and USB  
connector 3 (right)  
21  
22  
23  
24  
TPM  
Trusted Platform Module (TPM) connector  
System battery  
BHI  
PCIE_G3_X16 (CPU1)  
CPLD_DBG  
PCI-e Gen3 x16 slot 1 (processor 1)  
CPLD debug connector  
86  
Item  
Connector  
Description  
25  
UART  
Universal Asynchronous Receiver/  
Transmitter (UART) connector  
26  
CPLD_JTAG  
Complex Programmable Logic Device  
(CPLD) JTAG connector  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
PCIE_G3_X16 (CPU1)  
SW2  
PCI-E Gen3 x16 Slot 2 (processor 1)  
Power button  
VGA1  
VGA port  
INT_TTL  
USB_DBG1  
MGMT  
Internal TTL COM connector  
USB to serial port  
LAN management connector  
Management port  
LAN 2 LED  
LAN3(BMC)  
CR21  
LAN2  
LAN 2 port  
CR20  
LAN 1 LED  
LAN1  
LAN 1 port  
CR3  
UID LED  
LSI 2008 SAS mezzanine card connectors  
Figure 36. LSI 2008 SAS mezzanine card connectors  
1.  
mini-SAS connector (port 0-3)  
LSI 2008 mezzanine card  
2.  
4.  
mini-SAS connector (port 4-7)  
mezzanine card connectors  
3.  
Jumper settings  
87  
   
System configuration jumper settings on the Dell XC6320 system board  
The function of system configuration jumper installed on each Dell XC6320 system board is shown  
below:  
Figure 37. System configuration jumpers on the Dell XC6320 system board  
Table 14. System configuration jumper on the Dell XC6320 system board  
Jumpers  
Function  
Disabled (Default state)  
Enabled  
BIOS Recovery  
1
No pin  
Pin 1-2  
NVRAM Clear  
PWRD_EN  
2
3
4
No pin  
Pin 1-2  
No pin  
Pin 1-2  
Pin 2-3  
Pin 1-2  
ME_FM Recovery  
88  
 
7
Getting help  
Contacting Dell  
Dell provides several online and telephone-based support and service options. If you do not have an  
active internet connection, you can find contact information on your purchase invoice, packing slip, bill,  
or Dell product catalog. Availability varies by country and product, and some services may not be  
available in your area. To contact Dell for sales, technical assistance, or customer-service issues:  
1. Go to Dell.com/support.  
2. Select your country from the drop-down menu on the bottom right corner of the page.  
3. For customized support:  
a. Enter your system Service Tag in the Enter your Service Tag field.  
b. Click Submit.  
The support page that lists the various support categories is displayed.  
4. For general support:  
a. Select your product category.  
b. Select your product segment.  
c. Select your product.  
The support page that lists the various support categories is displayed.  
5. For contact details of Dell Global Technical Support:  
b. The Technical Support page is displayed with details to call, chat, or e-mail the Dell Global  
Technical Support team.  
Dell SupportAssist  
For an enhanced Support Experience, Dell recommends installing and configuring Dell SupportAssist.  
Dell SupportAssist is a software application that transparently collects information about your system and  
automatically creates support cases when issues are detected. Dell SupportAssist helps Dell to provide  
you an enhanced, personalized, and efficient support experience. Dell uses the data to solve common  
problem, designs and markets the products.  
For more information about installing and configuring Dell SupportAssist, see: http://www.dell.com/en-  
Locating your system Service Tag  
Your system is identified by a unique Express Service Code and Service Tag number. The Express Service  
Code is found on the front of the system and Service Tag is found on the front of the system.  
Alternatively, the information may be on a sticker on the chassis of the system. This information is used  
89  
       
by Dell to route support calls to the appropriate personnel. The Service Tag locations on the chassis are  
as follows:  
Figure 38. Service Tag location  
Figure 39. Service Tag location on the left front panel  
Figure 40. Service Tag location on the chassis  
The linkage of 24 hard drives for four system boards is shown here. For information about other  
configurations, see theFront panel features and indicators Front panel features and indicators section of  
the Dell XC6320 Web-Scaled Converged Appliance Owner’s Manual.  
90  
Figure 41. Service Tag linkage  
NOTE: Hard drives that are under warranty are linked to the appropriate Service Tag of the node.  
Quick Resource Locator  
Use the Quick Resource Locator (QRL) to get immediate access to system information and how-to  
videos. This can be done by visiting Dell.com/QRL or by using your smartphone and a model specific  
Quick Resource (QR) code located on your Dell PowerEdge system. To try out the QR code, scan the  
following image.  
Figure 42. Quick Resource Locator  
91  
 

Sharp Ar C360p User Manual
Samsung As12aa Ab Mc User Manual
Radio Shack 273 1900 User Manual
Motorola Barcode Reader Cpx8216t User Manual
Mitsubishi Electronics Mitsubishi Electric Air Conditioner Etwork System Ai Controller Pac Yg63mca User Manual
Mitsubishi 6a1 Series User Manual
Jensen Jcr 238 User Manual
HP 3800 User Manual
BLACK DECKER GCO1440 User Manual
ACER ASPIRE 3650 User Manual