1
DELL S2719DC
1. Disassembly Procedures:
Open the pizza carton with a proper tool, then put
Lift up the stand , then use a Philips-head screwdriver
to remove 2pcs screws for unlocking the whole unit
including stand and base, then remove the stand and
base. Use a Philips-head screwdriver to remove 2pcs
screws for release the hinge cover.
S1
down the pizza carton, and open the carton.
S4
(No.1~2 screw size=M3x11, Torque=7.5±0.5kgfxcm;
No.3~4 screw size=M2x0.4x3.2, Torque=2~3kgfxcm)
2
1
Take out the QSG from the catron, and then take out
the Paper-Top with other accessories including
user’s manual, HDMI cable, power cable, power
adapter and other packing materials from the carton.
(Note: It depends on whether users returning the
accessories)
S2
3
4
QSG
Use a proper tool insert the gap of the rear cover top
side (marked 1) as the following picture to release the
rear cover, then wedge your fingers between the rear
cover and the panel to release the rear cover, then use
one hand to press the panel module, the other hand to
pull up carefully the rear cover in order of arrow
preference 1~3 for unlocking mechanisms of rear
cover, and then remove the rear cover carefully.
S5
2
1
3
3
Take out the whole packed monitor and then remove
the EPE bags which packed monitor and stand
base, and then put the monitor face down on the
table with protective cushion.
S3
3
DELL S2719DC
Disconnect the panel lamp cable from the connector
os the panel module, then remove bracket and put it
on a protect cushion for later disassembling. Unplug
the LVDS cable and panel lamp cable from the
connectors of panel module. Tear off the mylar tape
which is sticked on the specific position of the back of
panel, and then use a Philips-head screwdriver to
remove 3pcs screws for unlocking the panel module.
(No.1~3 screw size=M3x2.7, Torque=3~4kgfxcm)
Turn over the bracket chassis module. Use a Philips-
head screwdriver to remove 5pcs screws for
unlocking the main board.
S13
(No.1~3 screw size=M3x7.5, Torque=7.5±0.5kgfxcm)
S11
1
3
5
4
2
Remove the main board from the bracket chassis
module by taking out the panel lamp cable from the
hole of the bracket carefully, and then disconnect all
of the cables.
S14
3
1
2
Put the bracket chassis on a protector cushion, then
use a Philips-head screwdriver to remove 4pcs
screws for unlocking the hinge.
S12
(No.1~4 screw size=M3x5.3, Torque=7.5±0.5kgfxcm)
1
4
2
3
DELL S2719DC
4
2. Product material information
The following substances, preparations, or components should be disposed of or
recovered separately from other WEEE in compliance with Article 4 of EU Council
Directive 75/442/EEC.
Capacitors / condensers (containing No used
PCB/PCT)
Mercury containing components
Batteries
No used
No used
Printed circuit boards (with a surface Product has printed circuit boards (with a
greater than 10 square cm)
Component contain toner, ink and
liquids
surface greater than 10 square cm)
No used
Plastic containing BFR
Component and waste contain
asbestos
No used
No used
CRT
No used
Component contain CFC, HCFC, HFC No used
and HC
Gas discharge lamps
No used
LCD display > 100 cm2
External electric cable
Component contain refractory
ceramic fibers
Product has an LCD greater than 100 cm2
Product has external cables
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors (height >
25mm, diameter > 25mm)
3. Tools Required
List the type and size of the tools that would typically can be used to disassemble the
product to a point where components and materials requiring selective treatment
can be removed.
Tool Description:
-
-
-
-
Screwdriver (Phillip head) #1
Screwdriver (Phillip head) #2
Penknife
Soldering iron and absorber
|