Installation Instructions
36 Inch Built-In Refrigerator
Models: EF36LNBSS, EF36RNBSS, IF36LNBOL, IF36RNBOL
Part No. 103677 Rev. E/W10291431
Refrigerator Safety
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
follow instructions.
You can be killed or seriously injured if you don't
instructions.
follow
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Use nonflammable cleaner.
Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
Do not use an adapter.
Use two or more people to move and install refrigerator.
Do not use an extension cord.
Disconnect power before installing ice maker (on ice maker
kit ready models only).
Disconnect power before servicing.
Replace all parts and panels before operating.
Remove doors from your old refrigerator.
Use a sturdy glass when dispensing ice (on some models).
SAVE THESE INSTRUCTIONS
Proper Disposal of Your Refrigerator
WARNING
WARNING
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned
refrigerators are still dangerous,
even if they sit out for “just a few
days.” If you are getting rid of
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
your old refrigerator, please follow
the instructions below to help
Failure to do so can result in death or serious injury.
prevent accidents.
Before you throw away your
old refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so
children may not easily climb
inside.
1
Model Identification
EF36LNBSS
EF36RNBSS
Refrigerator equipped with stainless steel doors.
Top door is hinged on left, handle mounts on right.
Refrigerator equipped with stainless steel doors.
Top door is hinged on right, handle mounts on left.
IF36LNBOL
IF36RNBOL
Refrigerator equipped with unfinished doors designed for installa-
tion of custom panels and handles.
Refrigerator equipped with unfinished doors designed for installa-
tion of custom panels and handles.
Top door is hinged on left, custom handle mounts on right.
Top door is hinged on right, custom handle mounts on left.
2
Installation Requirements
Tools and Parts
Location Requirements
Your Dacor refrigerator can be recessed in an opening between
cabinets or installed at the end of a cabinet run using a side panel
to enclose the refrigerator.
Tools needed:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
WARNING
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Cordless drill
Drill bits
Two adjustable wrenches
Phillips screwdriver
Small level
Appliance dolly
Torx ®† T15 and T27 screwdrivers
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
¹¹⁄32” nut driver
Failure to do so can result in death, explosion, or fire.
³⁄8” and ¹⁄2” open end wrenches
Allen wrench (5⁄32”)
¹⁄4” and 5/16” socket drivers
Tape measure
IMPORTANT:
ƒ
ƒ
Observe all governing codes and ordinances.
It is recommended that you do not install the refrigerator near
an oven, radiator, or other heat source.
Utility knife
PARTS NEEDED:
ƒ
ƒ
ƒ
ƒ
ƒ
Do not install in a location where the temperature will fall
below 55°F (13°C).
ƒ
ƒ
ƒ
Six #8 x 3” (7.6 cm) wood screws (longer screws may be
needed).
Floor must support the refrigerator weight, more than 600 lbs
(272 kg), door panels and contents of the refrigerator.
One or two 2” x 4” x 32” (5.1 cm x 10.2 cm x 81.3 cm) wood
board(s).
Ceiling height must allow for side tipping radius. See Tipping
Radius.
Minimum 7 ft (2.1 m) flexible codes approved water supply
line.
Location should permit doors to open fully. See Door Swing
Dimensions.
ƒ
ƒ
EF series models: Dacor handle kit.
Location must permit top grille removal. See Opening
Dimensions.
IF series models: Consult a qualified cabinetmaker
or carpenter to make the panels. See the Installation
Requirements section for more information.
Opening Dimensions
ƒ
To avoid tipping during use, the solid soffit must be within 1”
(2.5 cm) maximum above the refrigerator. If the solid soffit
is higher than 1” (2.5 cm) or one is not available, then the
refrigerator must be braced.
If the anti-tip boards are needed, they must be attached to the
rear wall studs 80” to 90” (203.2 cm to 228.6 cm) above the
floor. See Install Anti-Tip Boards for more information.
NOTE: A clearance of ¹⁄2” (1.3 cm) must be maintained above
the top grille in order for the top grille to be removed.
1/2” (1.3 cm)
† TORX is a registered trademark of Textron Innovations Inc.
3
Installation Requirements
Location Requirements (continued) Electrical Requirements
ƒ
Locate the refrigerator so that it may easily be pulled out from
the wall if service becomes necessary.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
ƒ
A grounded 3 prong electrical outlet should be placed within
4” (10.2 cm) of the right side cabinets or end panel. See
Electrical Requirements for more information.
WARNING
ƒ
The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. If the water shutoff valve is not in the cabinets, the
plumbing for the water line can come through the floor or
the back wall. See Water Supply Requirements for more
information.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
4”
(10.2 cm)
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15 or 20 Amp. fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an extension
cord.
83 1/2” (212.1 cm) min.
84 3/4” (215.3 cm)
to bottom of solid soffit
IMPORTANT: If this product is connected to a GFCI (ground fault
circuit interrupter) equipped outlet, nuisance tripping of the power
supply may occur, resulting in loss of cooling. Food quality and
flavor may be affected. If nuisance tripping has occurred, and if
the condition of the food appears poor, dispose of it.
77”
(195.6 cm)
35 1/2”
(90.2 cm)
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, remove the top grille and turn the master
power switch to OFF or disconnect power at the circuit breaker
box.
When you are finished, turn on the master power switch or
reconnect power at the circuit breaker box. Then reset the control
to the desired setting.
See page 5
24”
(61.0 cm) min.
NOTE: Flooring under refrigerator must be at same level as the
room. Face of cabinet must be plumb.
4
Installation Requirements
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
Water Supply Requirements
ƒ
ƒ
All installations must meet local plumbing code requirements.
ƒ
ƒ
ƒ
Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. The right-hand side is recommended.
Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
NOTE: If the water shut off valve is in the back wall behind the
refrigerator, it must be at an angle so that the water line is not
kinked when the refrigerator is pushed into its final position.
If your refrigerator has a water filter cartridge, it may further
reduce the water pressure when used in conjunction with a
reverse osmosis system. Remove the water filter cartridge.
If you have questions about your water pressure, call a licensed,
qualified plumber.
1” x 1”
(2.5 cm x 2.5 cm)
Tipping Radius
Be sure there is adequate ceiling height to stand the refrigerator
upright when it is moved into place.
Possible water
line locations
ƒ
ƒ
The dolly wheel height must be added to the tipping radius
when a dolly is used.
If needed, the tipping radius can be reduced. See Reduce
Tipping Radius.
Side Tipping Radius
1”
The side tipping radius varies depending upon the width of the
model.
(2.5 cm)
6”
6”
(15.2 cm)
(15.2 cm)
NOTE: Tip on side shown only.
ƒ
ƒ
If the water shutoff valve is not in the cabinets, the plumbing
for the water line can come through the floor. A ½” (1.3 cm)
hole for plumbing should be drilled at least 6” (15.2 cm) from
the right or left hand side cabinet or panel. On the floor, the
hole should be no more than 1” (2.5 cm) away from the back
wall. See Connect Water Supply.
Your refrigerator dealer has a kit available with a ¼” (6.4 mm)
saddle-type shutoff valve. Before purchasing, make sure a
saddle-type valve complies with your local plumbing codes.
ƒ
ƒ
Do not use a piercing-type or ³⁄16” (4.8 mm) saddle valve which
reduces water flow and clogs more easily.
Install the water supply line only in areas where the household
temperatures will remain above freezing.
90 1/2” (229.9 cm)
Water Pressure
A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of
a reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and 827
kPa). If a reverse osmosis water filtration system is connected
to your cold water supply, the water pressure to the reverse
osmosis system needs to be a minimum of 40 to 60 psi (276 to
414 kPa).
5
Installation Requirements
Product Dimensions
Front View:
Side View:
ƒ
Width dimensions were measured from trim edge to trim edge.
ƒ
The depth from the front of the top grille to the back of the
refrigerator cabinet is 25³⁄8” (64.5 cm).
ƒ
Height dimensions are shown with leveling legs extended ¹⁄8
”
(3.2 mm) below the rollers.
ƒ
ƒ
The power cord is 84” (213.3 cm) long.
The water line attached to the back of the refrigerator is 5 ft.
(1.5 m) long.
ƒ
Height dimensions are shown with leveling legs extended ¹⁄8”
(3.2 mm) below the rollers.
25 3/8”
(64.5 cm)
23 1/2”
(59.7 cm)
*83 3/8”
(211.8 cm)
*83 3/8”
(211.8 cm)
84” (213.4 cm)
Power Cord
36 1/4” (92.1 cm)
* When leveling legs are fully extended to 1¼” (3.2 cm) below
rollers, add 1¹⁄8” (2.9 cm) to the height dimensions.
Door Swing Dimensions
*3 1/2” (8.9 cm)
The location must permit both doors to open to a minimum of
90°. Allow 4½” (11.4 cm) minimum space between the side of the
refrigerator and a corner wall.
NOTE: More clearance may be required if you are using overlay
panels, custom handles or extended handles on a IF36 model.
* When leveling legs are fully extended to 1¼” (3.2 cm) below
rollers, add 1¹⁄8” (2.9 cm) to the height dimensions.
To adjust the door swing, see Adjust Doors.
Top View:
35 1/4”
(89.5 cm)
23”
(58.4 cm)
51”
(129.5 cm)
25 3/8”
(64.5 cm)
59”
(149.9 cm)
90˚
110˚
130˚
6
Installation Requirements
Door Panels and Cabinet Clearance - IF36 Series Models
The custom door panels and adjacent cabinets for models series IF36 must be designed so that there is sufficient clearance for the
doors to swing open. If the refrigerator is to be installed close to the wall, see Door Swing 90° on the following page.
Refrigerator to
Cabinet Clearance
Door swing 110°
actual size
Refrigerator
side trim
Cabinetry
1
110˚ door
stop position
/
4" (6.35 mm)
Hinge
1
/
2" (1.3 cm)
3
/
4" (1.9 cm)
1" (2.5 cm)
NOTE: For IF36 series models, rout
the hinge side of the custom door
panels to a radius that is equal to at
least half the thickness of the panel
if a 130° door swing is desired. See
Adjust Doors.
Spacer panel
When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinet to some degree.
7
Installation Requirements
Door Panels and Cabinet Clearance - IF36 Series Models (cont.)
Refrigerator to
Cabinet Clearance
Door swing 90°
actual size
Refrigerator
side trim
90° door
stop position
Cabinetry
1
4" (6.35 mm)
/
1
Hinge
/
2" (1.3 cm)
3
/
4" (1.9 cm)
1" (2.5 cm)
Spacer panel
Allow a minimum of 4½” (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if
thicker custom panels or custom handles are used. Do not overlook baseboards.
8
Installation Requirements
Custom Panels and Handles - IF36 Series Models
Custom overlay panels used with the IF36 model series allow you
to blend the exterior of your refrigerator into the overall kitchen
décor, and to use custom handles for additional design flexibility.
In some cases, your cabinet manufacturer may choose to work
with one panel routed for the different dimensions. Follow these
panel dimension and placement instructions to be sure that the
custom overlay panels will fit properly.
The custom panels must have backer panels attached in order
to mount them to the refrigerator. It is most common to work with
three panels, as shown in the graphic below. A decorative overlay
panel, a ¹/8” (3.2 mm) spacer panel or spacer strips and a
¼” (6.4 mm) backer panel.
IMPORTANT:
Install the panels after moving the refrigerator into
place (page 17) .
The weight of the overlay panels cannot exceed:
Overlay panel
Spacer panel
ƒ
ƒ
ƒ
50 lbs. (23 kg) for the refrigerator door.
20 lbs. (9.1 kg) for the freezer door.
10 lbs. (4.5 kg) for the top grille.
Spacer panel
1
/8"
Overlay panel
(3.2 mm)
To minimize panel weight, you may use 2” (5.1 cm) spacer strips
around the perimeter in place of full-sheet solid spacer panels.
The spacer strips must be set in at least 1” (2.5 cm) from the top,
bottom and sides edges of the backer panel. If you use spacer
strips, it is also recommended that you use two 2” (5.1 cm) strips
horizontally centered for added support.
Backer panel
Door
1" Min.
(2.5 cm)
Backer panel
Door/Grille trim
Offset dimension
5
3
"
"
/8 to /4
1
"
/4
(1.6 to 1.9 cm)
1
"
/8
(6.4 mm)
NOTE: For the grille and the door panels to be flush, the overlay
door panel should be ¼” (6.4 mm) thicker than the overlay grille
panel.
(3.2 mm)
34¹⁄2
(87.6 cm)
"
34¹⁄2
(87.6 cm)
"
8¹⁄2
(21.6 cm)
"
Top grille panel
Maximum weight: 10 lbs (4.5 kg)
7³⁄8
(18.7 cm)
"
Bottom offset
1" (2.5 cm)
34¹⁄2
"
(87.6 cm)
345⁄16
"
(87.2 cm)
Center
backer
panel
left to
right
49¹⁄8
(124.8 cm)
"
50"
(127.0 cm)
Refrigerator door panel
Maximum weight: 50 lbs (23 kg)
Bottom offset
7⁄16 " (11.1 mm)
34¹⁄2
"
(87.6 cm)
345⁄16
(87.2 cm)
"
Center
backer
panel
left to
right
20 9
(52.2 cm)
⁄
"
16
Freezer door panel
Maximum weight: 20 lbs (9.1 kg)
20³⁄16
"
(51.3 cm)
Bottom offset
¹⁄16 " (1.6 mm)
Overlay Panel Dimensions*
Backer Panel Dimensions*
* See page 10 for additional panel construction information
9
Installation Requirements
Custom Panels and Handles - IF36 Series Models (Continued)
Custom Panels Construction Information
Custom Handles
See page 9 for overall dimensions.
• Before installing a custom panel
assembly, you must install the custom
handle hardware. The handle and handle
mounting hardware are not provided with
the refrigerator.
NOTE: Spacer panels must be at least 1” (2.5 cm) from the top,
bottom, and side edges of the backer panel.
3-Piece Grille Overlay Panel Configuration
Top View
Side View
• Dacor recommends handles with larger
D-style pulls. Any handle designed for
use with an appliance should produce
satisfactory results. Handle kits are
available through your Dacor dealer.
D
C
B
• Handle kits do not include the
necessary mounting screws since
screw length required varies with the
total thickness of the panels. The
panel craftsman must determine and
obtain the proper fasteners for the
application. If using screws with thick
heads, they must be countersunk into
the panel before installing the handles.
20” Typ.
(50.8 cm)
36” Max.
(91.4 cm)
1”
(2.5 cm)
A. Offset dimension
IMPORTANT: Dacor does not advise the
use of single pull knobs.
A
B. 1/4” (6.4 mm) backer panel
C. 1/8” (3.2 mm) spacer panel
D. 3/4” (1.9 cm) decorative overlay panel
3-Piece Door Overlay Panel Configuration
B
1”
A
D
C
A
B
(2.5 cm)
A. Offset dimension
Trim frame
B. 1/4” (6.4 mm) backer panel
C. 1/8” (3.2 mm) spacer panel
surrounding door
D. 3/4” (1.9 cm) decorative overlay panel
1-Piece Overlay Panel Configuration
Door
In some cases, your cabinet manufacturer may choose to work
with one panel routed for the different dimensions. Follow these
panel dimensions and placement instructions to be sure that the
custom overlay panels will fit properly.
C
A. Countersunk screw
B. Handle
C. Door panel assembly
Handle Detail
10
Installation Requirements
Inset Installation Dimensions
Custom Side Panels - Model IF36
1. Measure the distance from point A (as shown) to the back
wall. Add ¹⁄32” (0.8 mm) to this measurement to allow the side
panel to fit into the trim.
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed at the end of a cabinet run. You
may choose an inset or recessed inset panel installation for model
IF36.
2. If the panel is more than ³⁄8” (9.5 mm) thick, rout the front edge
to allow the side panel to fit into the trim.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type
of installation you are planning.
Back
Wall
NOTES:
ƒ
ƒ
ƒ
The dimensions shown are actual product dimensions and
may not reflect the needed installation dimensions.
A
The side panel should be a minimum of ½” (1.3 cm) thick to
avoid warping.
If the opening depth is 25” (63.5 cm) or more, you may want to
install a support board on the rear wall.
Refrigerator
Recessed Inset Installation Dimensions
Overlay
1. Measure the distance from point B (as shown) to back wall.
2. Route the front edge of the support board or attach a ³⁄8” (9.5
mm) board to hold the panel in the cabinet side trim.
23 11/16”
(60.2 cm)
Back
Wall
B
Side Trim
3/16” (4.8 mm)
3/8” (9.5 mm)
1/16” (1.6 mm)
3/32” (2.4 mm)
11
Installation Requirements
Inset Installation Dimensions
Custom Side Panels - Model EF36
1. Measure the distance from point A (as shown) to the back
wall. Add 7⁄32” (5.6 mm) to this measurement to allow the side
panel to fit into the trim.
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed at the end of a cabinet run. You
may choose an inset, flush or recessed inset panel installation for
model EF36.
2. If the panel is more than ¼” (6.4 mm) thick, route the front
edge to allow the side panel to fit into the trim.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type
of installation you are planning.
Back wall
NOTES:
ƒ
ƒ
ƒ
The dimensions shown are actual product dimensions and
may not reflect the needed installation dimensions.
A
The side panel should be a minimum of ½” (1.3 cm) thick to
avoid warping.
If the opening depth is 25” (63.5 cm) or more, you may want to
install a support board on rear wall.
Refrigerator
Flush Installation Dimensions
1. Measure the distance from point B (as shown) to the back
24 1/8”
wall.
(61.3 cm)
2. Attach the support board with a screw or adhesive that is
compatible with aluminum and wood.
231116”
(60.2 cm)
/
23 1/2”
(59.7 cm)
Back wall
Side Trim
1/4” (6.4 mm)
11/64”
(4.4 mm)
B
3/16” (4.8 mm)
7/32” (5.6 mm)
Recessed Inset Installation Dimensions
1. Measure the distance from point C (as shown) to the back
wall.
2. Route the front edge of the support board or attach a
¼” (6.4 mm) board to hold the panel in the cabinet side trim.
Back wall
5/8”
(1.6 cm)
13/32” (1.0 cm)
C
12
Installation Instructions
1. Grasp both ends
of the top grille.
B
B
A
Unpack Refrigerator
2. Push the top grille
straight up, then
WARNING
pull straight out.
Lay the grille on a
soft surface.
3. Remove the six
screws attaching
each cabinet
A. Top grille
B. Cabinet side trim
Tip Over Hazard
side trim to the
refrigerator and remove the side trims.
Refrigerator is top heavy and tips easily when not
completely installed.
Move Refrigerator into House
Keep doors taped closed until refrigerator is
completely installed.
WARNING
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
IMPORTANT:
ƒ
ƒ
ƒ
ƒ
If you receive a damaged product, immediately contact your
dealer or builder. Do not install or use a damaged appliance.
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Do not remove the film on the outside until the refrigerator is in
its operating position.
Keep doors taped closed until refrigerator is
completely installed.
All four leveling legs must contact the floor to support and
stabilize the full weight of the refrigerator.
Use two or more people to move and install
refrigerator.
Keep the cardboard shipping piece or plywood under the
refrigerator until it is installed in the operating position.
Failure to do so can result in death or serious injury.
1. Remove and save the literature package bag taped to the side
of the refrigerator and the parts bag behind the grille. Remove
the four brackets (two on each side) that attach the shipping
base to the refrigerator bottom.
1. Place an appliance dolly under the left side of the refrigerator
as shown. Be sure to avoid damaging the side trims and
handles. Place the corner posts from the packing materials
over the trims and handles as appropriate. Slowly tighten the
strap.
NOTE: Do not remove tape and door bracing until the
refrigerator is in its final position.
2. If necessary, reduce the tipping radius. See Tipping Radius
(page 5) for ceiling height requirements or Reduce Tipping
Radius for step-by-step instructions. If you do not need to
reduce the tipping radius, proceed to Move the Refrigerator
into House.
NOTE: Pass the dolly strap under the handle for EF36 series
models.
2. Place
pieces of
the shipping
carton on the
floor when
rolling the
dolly and
refrigerator
into the
house.
Reduce Tipping Radius
(if required)
Before bringing the refrigerator into the home, be sure there is
adequate ceiling height to stand the refrigerator upright. See
Tipping Radius (page 5).
Move the
If you do not have adequate ceiling height to stand the refrigerator
upright, the tipping radius can be reduced by removing the top
grille and side trims. The reduced tipping radius will be 88” (223.5
cm).
refrigerator
close to the
built-in opening.
3. Place top of cardboard carton or plywood under refrigerator.
4. Stand the refrigerator up. First, place the left bottom edge of
the refrigerator on the floor, stand the refrigerator upright and
then lower the right-hand side of the refrigerator to the floor.
5. Do not remove film on the outside.
6. Reassemble the trim and top grille after the dolly has been
removed from the refrigerator.
13
Installation Instructions
Install Anti-Tip Boards
Connect Water Supply
IMPORTANT:
Read all directions before you begin.
ƒ
To avoid tipping during use, the solid soffit must be within 1”
(2.5 cm) maximum above the refrigerator. If the solid soffit
is higher than 1” (2.5 cm) or one is not available, then the
refrigerator must be braced.
IMPORTANT: If you turn the refrigerator on before the water line
is connected, turn the ice maker off.
Install Saddle Valve
NOTE: If existing water line meets the Water Supply
ƒ
ƒ
ƒ
ƒ
It is recommended that board(s) be installed before the
refrigerator is installed.
Requirements, see Connecting to Refrigerator.
1. Unplug the refrigerator or disconnect power.
Board(s) must be long enough to fully cover the width of the
compressor cover.
2. Turn off main water supply. Turn on nearest faucet long
enough to clear line of water.
Locate the board(s) so the bottom surface(s) of the board(s) is
(are) 84” (213.4 cm) from the floor.
3. Locate a ½” to 1¼” (1.3 cm to 3.2 cm) vertical cold water pipe
near the refrigerator.
During installation, raise the refrigerator up so there is ¼” (6.4
mm) maximum between the top of the refrigerator and the
bottom of the anti-tip board(s). Do not crush the compressor
cover when raising the rear leveling legs.
IMPORTANT:
ƒ
ƒ
Make sure it is a cold water pipe.
A horizontal pipe will work, but drill on the top side of the pipe,
not the bottom. Doing so will help keep water away from the
drill and normal sediment from collecting in the valve.
To Install Anti-tip Boards
1. Mark the stud locations on rear wall 80” to 90” (203.2 cm to
228.6 cm) above floor.
4. Using a cordless drill, drill a ¼” (6.4 mm) hole in the cold water
pipe you have selected.
2. Securely attach one or two 2” x 4” x 32” (5.1 cm x 10.2 cm x
81.3 cm) boards to wall studs behind refrigerator. Use six #8
x 3” (7.6 cm) (or longer) wood screws. The wood screws must
be screwed into the studs at least 1½” (3.8 cm). The board(s)
must overlap the compressor cover.
5. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the ¼” (6.4 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten.
A
B
A
B
A. Cold water pipe
B. Pipe clamp
C
C
C. Packing nut
D. Shutoff valve
2” (5.1 cm)
D
6. Turn on the main water supply.
7. Check for leaks around the saddle valve.
IMPORTANT: Before attaching the water supply line to the
shutoff valve, flush the main water supply line to remove
particles and air in the water line. Allow enough flow so that
the water becomes clear. Flushing the water line may help
avoid filters and/or water valves from becoming clogged.
D
A. Center board 1/4” (6.4 mm) max. above refrigerator
B. Two 2” x 4” x 32” (5.1 cm x 10.2 cm x 81.3 cm) boards
C. Attach to studs with six #8 x 3” (7.6 cm) screws
D. Compressor cover
14
Installation Instructions
Connecting to Refrigerator
Plug in Refrigerator
1” x 1”
WARNING
(2.5 cm x 2.5 cm)
Possible water
line locations
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
1”
(2.5 cm)
7”
Do not use an extension cord.
(17.8 cm)
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Set control switch at top of cabinet to the off position.
2. Plug into a grounded 3 prong outlet.
Move to Final Location
NOTE: The flexible codes approved water supply line can connect
to the supply valve through the floor or through the side cabinets,
as indicated by the gray boxes above.
WARNING
1. Unplug the refrigerator or disconnect power.
2. Connect the 7 ft (2.1 m) minimum flexible codes approved
water tube to the water supply valve.
3. Flush the main water supply line to remove particles and air in
the water line. Allow enough flow so that the water becomes
clear.
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
4. Tape the water supply line to the floor, 7” (17.8 cm) from the
left side of the refrigerator. Tape along the length of the tubing,
which will allow it to pass beneath the refrigerator without
interference.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
NOTE: Allow a minimum of 26” (66.0 cm) of flexible codes
approved water supply line to be loose at the front of the
refrigerator for connecting to the household water line.
Failure to do so can result in death or serious injury.
5. Connect the water supply line to the refrigerator.
IMPORTANT: To avoid floor damage, make sure levelers are
raised (not touching floor) and refrigerator is on rollers before
moving.
NOTE: If the main water shutoff valve is behind the
refrigerator, a secondary water shutoff valve may be installed
in line with the water supply line at the front of the product.
1. Place top of cardboard carton or plywood under refrigerator.
Remove dolly.
A. Household water line
B. Coupling
C. Bulb
D. Nut
2. Do not remove film on the outside.
B
3. Move the refrigerator straight back, evenly into the opening.
Be sure that the refrigerator side trims are not interfering with
the door opening. Also, be sure that the water tubing is not
kinked and the power supply cord is on top of the refrigerator.
A
E. Refrigerator water
E
tubing
D
C
6. Turn on the water valve and check all connections for leaks.
15
Installation Instructions
3. Continue adjusting all of the leveling legs to raise the
Level and Align Refrigerator
refrigerator until the top is within at least 1” (2.5 cm) of the top
soffit.
WARNING
NOTE: If an anti-tip board has been used, adjust the leveling
legs until the top of the refrigerator is within ¼” (6.4 mm) of
the bottom of the anti-tip board as shown. Do not crush the
compressor cover.
A
B
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
C
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
2” (5.1 cm)
Failure to do so can result in death or serious injury.
IMPORTANT: All four leveling legs must contact the floor to
support and stabilize the full weight of refrigerator. Rollers are for
moving refrigerator and not for permanent support.
After moving the refrigerator to its final location:
D
1. Use a 5⁄16” socket driver to turn the leveling bolts clockwise to
extend the legs to the floor as shown. The rollers should be off
the floor.
A. Center board 1/4” (6.4 mm) max. above refrigerator
B. Two 2” x 4” x 32” (5.1 cm x 10.2 cm x 81.3 cm) boards
C. Attach to studs with six #8 x 3” (7.6 cm) screws
D. Compressor cover
IMPORTANT: Adjust in small increments to keep from
damaging the cabinet trim and causing problems with the door
alignment or top grille fit. To avoid damage to the cabinet or
leveling legs, do not apply more than 50 inch-pounds (5.65
Nm) of torque to the leveling bolts. The leveling legs can be
extended to a maximum of 1¼” (3.2 cm) below the rollers.
A
B
B
A
A. Rear leveling bolt
B. Front leveling bolt
4. For IF series models, additional adjustments may be needed
after the custom panels are installed.
2. Adjust the leveling legs to level and align the refrigerator from
left to right and front to back so that the refrigerator is level
and aligned with the cabinets. The cabinet surface must be
plumb for the ideal fit of the refrigerator side trim.
16
Installation Instructions
Custom Panel and Handle Installation - IF36 Series Models
IMPORTANT:
4. Slide the custom panels into the bottom and hinge side trims
on the refrigerator compartment and freezer compartment
doors, making sure that the backer panel fits into the hinge
side trims.
ƒ
ƒ
ƒ
Install the custom handles prior to installing the panels on the
refrigerator.
Create custom door overlay panels according to the
specifications in the Custom Panels and Handles section.
Dacor is not responsible for customer installed molding or
decorative panels that need to be removed or replaced to
service the refrigerator.
Handle Installation
Before installing a custom panel assembly, install the custom
handle hardware.
Counter-sink the screw head into the back of the panel to allow
the panel to slide into place smoothly and for proper fit.
D
B
A
D
A. Countersunk screw
B. Handle
D. Panels
C
5. Reinstall the trims and corner caps.
C. Door panel assembly
6. Remove the film from the screw covers. Slide or snap the
screw covers into the handle trim section.
Side View
Front View
Door Panel Installation
E
1. Remove all tape and door bracing from the refrigerator and
freezer doors.
2. Open the refrigerator and freezer compartment doors.
3. Remove the trims and corner caps.
A
B
E. Screw cover
7. Check refrigerator level and alignment. Adjust if needed.
Continued...
C
A
A
A. Corner caps
B. Refrigerator door trims
C. Freezer drawer trim
17
Installation Instructions
Custom Panel Installation - IF36 Adjust Doors
Door Swing Adjustment
Series Models (Continued)
1. Check that the refrigerator door can open freely. If the door
opens too wide, remove the door stop screw or screws
(depending on your model) from the bottom hinge with a Torx
T15 screwdriver.
Top Grille Panel Installation
1. Grasp both ends of the top grille.
2. Push straight up, then pull straight out. Place the top grille
panel-side down on a soft working surface.
2. Hold the door open to a position that is less than 90°.
3. Replace the door stop screw or screws in the bottom hinge
and tighten.
B
B
A
A. Door stop screw
A. Top grille
B. Cabinet side trim
3. Remove one end cap by loosening the nuts and sliding the
end cap off.
A
C
D
B
B. 130°
C
C. 110° (IF series refrigerators)
D. 90°
IMPORTANT: Do not place the door stop screw in the 130°
position on IF Series models. See “Handle and Door Clearances.”
E
D
Door-to-Door or Door-to-Refrigerator Trim
Adjustment
C. Bottom rail
D. Nuts
1. Loosen, but do not remove, the four Torx 27 flat-head
mounting screws and the two ¼” hex head mounting screws.
E. End cap
F. Top rail
F
2. Adjust the top hinge of either door to align it with the other
door or the refrigerator trim.
4. Slide the custom panel into the top grille channel and reattach
the end cap.
3. Tighten the four Torx 27 flat-head mounting screws to a torque
of approximately 100 inch-pounds (11.3 Nm) and tighten the
two ¼” hex head mounting screws.
A
B
G
A. Torx 27 flat-head mounting screws
B. 1/4” hex-head mounting screws
G. Custom Panel
5. Replace the top grille in the cabinet side trims and pull the
panel down slightly to lock it into place.
18
Installation Instructions
3. Snap the skirt onto the base grille.
Install Side Panel(s)
If the built-in area depth is 25” (63.5 cm) or more, the side panels
can be installed inside the side trim or attached to the outside of
the side trim.
IMPORTANT: Dacor is not responsible for customer installed
molding or decorative panels that need to be removed or replaced
to service the refrigerator.
1. For the inside side trim piece, slide the front edge of the
routed side panel into the trim piece.
A
B
2. Nail the rear edge of the panel to the support board.
A
A. Base grille
B. Skirt
4. Trim the skirt by scoring the proper “V” groove with a utility
knife. Break the skirt at the score line.
C
C. “V” groove
5. Using the two screws, attach the base grille assembly to the
refrigerator as shown.
B
NOTE: Secure the right screw in place first.
A. Support board (mounted to back wall)
B. Cab side trim
Install Base Grille
There are two pieces to the base grille to allow for a custom fit:
the base grille itself and the skirt. The skirt can be added to the
base grille in order to extend it all the way to the floor.
1. To see if the skirt is needed, place the base grille into position.
Do not attach the base grille to the refrigerator. Measure the
distance between the bottom of the base grille and the floor.
The gap must be a minimum of ½” (1.3 cm) in order to add the
skirt.
D
NOTE: If the gap measures less than ½” (1.3 cm), skip steps 3
and 4 of the instructions, and install the base grille only.
D. Screws (2)
2. Remove the film on the outside of base grille.
19
Installation Instructions
Any questions or problems with this installation should be directed
Complete Installation
to your Dacor dealer or the Dacor Customer Service Team at
com.
1. Turn the water supply line valve to the “Open” position.
2. Turn the refrigerator switch to the on position. See Power On/
Off Switch in the use and care manual for instructions. Wait a
few minutes. Check the water line connections for leaks.
If you need service, be sure to have the model and serial
numbers when you call. You’ll find these numbers on the serial
number label, located on the right hand side of the fresh food
compartment.
3. Remove all boxes, parts packages and packing materials from
the interior of the refrigerator. See the Care and Cleaning
section in the use and care manual for instructions. Remove
the film and cardboard from the grille and doors or door frame,
depending on your model.
4. Install the shelves and bins in the refrigerator and freezer
compartments.
5. The controls are preset at the factory to the midpoint setting.
Check that the compressor is operating properly and that all
the lights are working.
6. Flush the water system before use. See Water System
Preparation.
To get the most efficient use from your new built-in refrigerator,
read your use and care manual. Keep Installation Instructions and
the use and care manual near the refrigerator for easy reference.
Water System Preparation
Please read before using the water system.
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Immediately after installation, follow the steps below to make sure
that the water system is properly cleaned.
1. Turn off the ice maker. Slide the ice maker On/Off control,
located on the left-hand side of the ice bin, to the off (down)
position as shown.
A
A. On/Off control
NOTE: If your model has a base grille filter system, make sure the
base grille filter is properly installed.
2. Turn on the ice maker. Slide the ice maker On/Off control,
located on the left-hand side of the ice bin, to the on (up)
position. Please refer to Ice Maker and Storage Bin section
in the use and care manual for further instructions on the
operation of the ice maker.
ƒ
ƒ
Allow 24 hours to produce the first batch of ice.
Before using the ice, fill and discard two full containers of
ice to prepare the filter for use.
20
|