- Retains factory features in select GM LAN 29 Bit vehicles while functioning with an aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- iPhone Voice Recognition (VR) feature from SWC on Kenwood, Pioneer, Alpine and JVC radios.
- Supports Pick Up/End Call, Pick Up and Toggle between 1st and 2nd Incoming call, AVRCP Track, Seek.
- Supports Bose, non-Bose and Y-91 audio systems.
- Provides Factory Rear Seat Entertainment Activation. Requires Cable #CRUX2333A
(sold separately).
- Retains factory front and back park assist system.
- Retains chime functions.
- EIA color coded wiring for easy installation.
BUICK
GMC
2008-2015
2006-2011
Enclave
Lucerne
2007-2015
2008-2013
2007-2013
Acadia
Savana**
Sierra 1500-3500
Pickup*
CADILLAC
2006-2011
2007-2014
2007-2009
DTS
Escalade
SRX
2007-2014
Yukon*
HUMMER
2008-2009
H2
CHEVROLET
2007-2013
2007-2008
2008-2013
2006-2013
2006-2007
2007-2013
Avalanche*
Equinox
PONTIAC
2007-2009
Torrent
Express Van**
Impala / Impala SS
Monte Carlo
Silverado 1500-3500
Pickup*
SATURN
2007-2010
2008-2009
Outlook
Vue
2007-2014
2007-2014
2009-2015
Suburban*
Tahoe*
Traverse
SUZUKI
2007-2008
XL7
1. *NOT compatible with 2012-Up SUVs/Trucks that are equipped with factory-installed Navigation
radios.
2. **NOT compatible with Express and Savana vans that are powered by a diesel engine.
3. Supports Rear Entertainment System with special order harness #CJA2333A (sold separately).
4. DOES NOT support ONSTAR.
SWC Cables
GM-49 Module GM-49 Harness
Antenna Adaptor
1 / 6
CRUX2543
Dash Kit
Rev.032917
If the vehicle is equipped with a Bose system, the DKGM-49 module has a built-in Bose adaptor that allows the
proper audio input gain from the aftermarket radio to the Bose amplifier. To use this feature, plug in the male 8-pin
connector on the harness to the GRAY female 8-pin connector on the DKGM-49 module. The module is also labeled
“Bose” and “Non Bose” to avoid confusion. (see picture below)
If the vehicle is NOT equipped with a Bose system, plug in the male 8-pin connector to the BLACK female 8-pin on
the GM-49 module.
Non-BOSE
BOSE
Connection
Connection
The DKGM-49 module has a potentiometer to adjust the chime volume. It is set at half way by default. To adjust
the volume, simply use a suitable screw driver and turn the potentiometer clockwise to increase the volume and
counter-clockwise to decrease the volume.
Chime
Volume
Adjustment
You can retain use of the factory backup camera by using the CRUX2543 harness provided in the kit. See below for
connection instructions. (Note: Loose wires may not be needed in the installation.)
3 / 6
Rev.032917
A double DIN radio replacement dash kit is included in the kit to make the installation quick and easy. You have the
option of installing a Double DIN or two Single DIN radios. The DKGM-49 kit includes:
(1) Main trim ring
(1) Left ISO mounting bracket
(1) Right ISO mounting bracket
Installation:
NOTE: Suzuki XL7 trim top corners of radio housing. See diagram A.
Diagram A
Before installation:
1. Locate the main trim ring.
2. Locate the left and right mounting brackets.
3. Slide the appropriate mounting bracket into the trim ring, aligning the holes in the trim ring to the clips on the bracket.
(See Diagram B)
4.For two Single DIN radio installation, slide the stacked ISO DIN unit into the trim ring bracket assembly and secure the unit to
the kit using the screws supplied with the radio. (See Diagram C)
Diagram C
Diagram B
4 / 6
Rev.032917
STEERING WHEEL CONTROL BUTTON FUNCTIONS
SWC Button
SHORT PRESS
LONG PRESS
PIONEER
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
Step Increment
Step Decrement
Preset Up
Preset Down
Source
Tune
Pick Up Call
Continuous VOL +
Continuous VOL -
Seek Up
End Call
Power On/Off
Mute On/Off
►I
Voice
Activate VR/Deactivate VR
SWC Button
SHORT PRESS
LONG PRESS
ALPINE
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
Step Increment
Step Decrement
Seek Up
Seek Down
Source
Continuous VOL +
Continuous VOL –
None
End Call
None
►I
Voice
Preset
Pick Up Call
ATT On/Off
Activate VR*/Deactivate VR*
*NOTE:
To Deactivate VR = Say “CANCEL”
BT Mode Active:
Voice = Toggle between 1st and 2nd Call
SWC Button
SHORT PRESS
LONG PRESS
CLARION
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
Step Increment
Step Decrement
Preset Up
Preset
Source
None
Continuous VOL +
Continuous VOL –
Seek Up
End Call
Power On/Off
Mute On/Off
Mute On/Off
►I
Voice
Pick Up Call
SWC Button
SHORT PRESS
LONG PRESS
JVC
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
Step Increment
Step Decrement
Seek Up
Seek Down
Source
Continuous VOL +
Continuous VOL –
M-Seek Up
End Call
None
►I
Voice
Preset
Pick Up Call
Mute On/Off
Activate VR
To Deactivate VR = Say “CANCEL”
NOTE:
5 / 6
Rev.032917
SWC Button
SHORT PRESS
LONG PRESS
KENWOOD
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
Step Increment
Step Decrement
Seek Up
Seek Down
Source
Continuous VOL +
Continuous VOL -
None
End Call / Deactivate VR
None
►I
Voice
Preset
ATT On/Off
Activate VR
Pick Up Call / Call History On/Off
NOTE:
To Deactivate VR = Say “CANCEL”
BOSS Radio SWC Programming
SWC Radio Wiring connection
SWC Key1 (Brown-wire) connect to Female 3.5 mm Jack - Brown wire
SWC Key2 (White-wire) connect to Female 3.5 mm Jack - Brown/White wire
SWC GND (Black-Wire) connect to Radio Negative wire (Black)
Programming the Radio
Press: [SETTING] > [STEER] > [RESET] > [High Z]
Press the Steering Wheel Control (SWC) buttons set the values as listed below:
Vol – [ 4.07]
Vol + [ 3.66]
Seek – [ 3.37]
Seek + [ 2.98]
Mode [1.39]
OFF Hook [ 0.00]
The Value in the bracket [X.XX] will vary and will be used as parameter for each assigned function.
Press: [Assign] > [4.07] > [Vol-], then the [4.07] will be replaced with [ Vol-]
With [Assign] highlighted:
Press: [3.66] > [Vol+], then the [3.66] will be replaced with [Vol+]
Press: [3.37] > [Seek-], then the [3.37] will be replaced with [Seek-]
Press: [2.98] > [Seek+], then the [2.98] will be replaced with [Seek+]
Press: [1.39] > [Mode], then the [1.39] will be replaced with [Mode]
Press: [0.00] > [Call], then the [0.00] will be replaced with [Call]
Press: [Enter] for Save the setting and Exit
6 / 6
Rev.032917
|