Rev. 091817
BLUETOOTH CONNECTIVITY FOR SELECT CHRYSLER, DODGE, JEEP VEHICLES 2006-UP w/AMP
INSTALLATION OVERVIEW
BEECR-35P
work. Following these instructions from “Start” to” Finish” will ensure
22-PIN
22-PIN
(female plug)
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
(male plug)
GRAY 22-PIN
PARTS INCLUDED:
(1) CR-35P Interface Module
(1) CR-35P T-Harness
(1) Instruction Sheet
(1) Microphone
TO FACTORY
RADIO
MODELS LISTED BELOW MUST
BE EQUIPPED WITH SWC.
TO FACTORY
HARNESS
(1) Set of Phone Stickers
CHRYSLER
2011 - 2013 200
2008 - 2010 300
2008 - 2010 Aspen
2007 - 2010 Sebring
2008 - 2013 Town & Country
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
durring the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
MIC
PRELIMINARY:
DODGE
Please read the entire manual before installing this interface.
2007 - 2013 Avenger
2009 - 2012 Caliber
2009 - 2013 Challenger
2008 - 2010 Charger
2008 - 2010 Dakota
2008 - 2013 Durango
2009 - 2013 Grand Caravan
2009 - 2010 Journey
2008 - 2009 Magnum
2007 - 2010 Nitro
THIS INTERFACE STREAMS THE HANDS-FREE & MUSIC (A2DP)
THROUGH THE TWO FRONT SPEAKERS ONLY.
3-PIN
(female plug)
INSTALLING THE INTERFACE
1. Remove the factory radio from the dashboard.
2. Remove the factory connectors from behind the factory radio.
3. Mate the interface connections to the factory connectors.
Make sure the 22-pin connector is properly seated into the interface.
4. Route the microphone to your desired location. Recommended are
is above the rear-view mirror.
GRAY
12-PIN
(male plug)
BLUETOOTH
MODULE
24-PIN
(male plug)
2009 - 2012 Ram
10-PIN
(male plug)
JEEP
2008 - 2010 Commander
2009 - 2013 Compass
2008 - 2013 Grand Cherokee
2008 - 2013 Liberty
2009 - 2013 Patriot
2007 - 2017 Wrangler
ENABLE VOICE DIAL AND MENU STRUCTURE
Important: Enabling the voice dial feature will disable the TUNE DOWN
function on the steering wheel control.
12-PIN
(male plug)
1. Place dip switch one to the ON. (As shown below)
TO ENABLE
VOICE DIAL
BLACK
MITSUBISHI
2006 - 2009 Raider
ON
CAN
BOX
1
2
3
4
5
6
VOLKSWAGEN
2009 - 2013 Routan
INITIAL PAIRING
STEERING WHEEL CONTROLS
With voice dial activated the
vehicle will lose TUNE DOWN
on the SWC
1. Turn on the vehicle and wait 15 seconds until the interface
announces “Please Select Your Mobile Phone” and Enter “0000”
2. From your mobile phone, choose and connect to the “Beeline”
device using the password “0000”.
All Bluetooth functionality is done on the steering wheel controls.
THIS INTERFACE DOES
SUPPORT AMPLIFIED SYSTEMS:
VOL UP
SEEK UP
SEEK DN
3. The interface will announce “Pairing Successful” then
“Phone Connected” after the pairing process is complete.
MOUNTING THE MICROPHONE
1. Insert the mounting clip into the ball joint on the microphone.
2. Mount the clip on your visor or near the rear view mirror.
3. Route the remaining cable along the edge of the roof liner and
towards the back of the radio, hiding the cable from sight.
Note: The Bluetooth interface will remember up to the last 8 devices.
Vehicles listed above must have
the “GRAY” 22-Pin connector.
Radio type does not matter.
VOL DN
power back on to re-attempt, if unsuccessful please contact our tech
support line.
BACKSIDE CONTROLS
Controls are found on the back-side of the steering wheel.
10 AND 12-PIN CONNECTORS
IMPORTANT: The GRAY 12-PIN CONNECTOR ATTACHED WITH THE
BLACK 10-PIN CONNECTOR GO TO THE BLUETOOTH MODULE
ONLY.
AUTO RE-CONNECT
The BEELINE module will automatically re-connect the a previously
paired mobile phone when the ignition is turned “ON” to the vehicle
and the mobile phone’s Bluetooth feature is also on.
Applications are subject to change
without notice.
RADIO CONTROL
There is no Bluetooth control on the factory radio.
All controls are done from the steering wheel controls.
Note: The Bluetooth module will re-connect with the last mobile
phone’s it was paired with. If no mobile phone is not found, it will
revert to the pairing process.
|