Camera User Guide
•
•
•
Make sure yeahis guide, including the “Safety
Precautionson, before using the camera.
Readng this e will help you learn to use the camera
propey.
Store this guide safely so that you can use it in the future.
ENGLISH
Read This First
•
•
Take some initial test shots and play them back to make sure the images
were recorded correctly. Please note that Canon Inc., its subsidiaries and
affiliates, and its distributors are not liable for any consequential damages
arising from any malfunction of a camera or accessory, including memory
cards, that results in the failure of an image to be recorded or to be
recorded in a way that is machine readable.
The images recorded with this camera are intended for personal use. Do
not record images that infringe upon copyright laws without the prior
permission of the copyright holder. Please be advised that in certain cases
the copying of images from performances, exhibitions, or commercial
properties by means of a camera or other device may contravene copyright
or other legal rights even if the image was shot for personal use.
This camera’s warranty is only effective in the country of sale. If there is a
problem with the camera while abroad, please return it to the country of
sale before proceeding with a warranty claim to a Canon Customer
Support Help Desk. For Canon Customer Support contacts, please see the
customer support list supplied with your camera.
•
•
The LCD monitor and viewfinder are produed with extremely high-
precision manufacturing techniqueore thn 99.99% of the pixels
operate to specification, but sioally non-performing pixels may
appear as bright or dark dotsis not a malfunction and has no effect
on the recorded image
•
•
The LCD monitor may be covered with a thin plastic film for protection
against scratches during shipment. If covered, remove the film before
using the camera.
Please take care when operating the camera for an extended period as the
camera body may become warm. This is not a malfunction.
3
What Do You Want to Do?
4 Shoot
Take good people shots
I
w
P
Portraits
(p. 61)
At the Beach
(p. 62)
Against Snow
(p. 62)
Shoot various other scenes
Landscape
(p. 61)
Sports
(p. 60)
Night Scenes
(p. 62)
t
Fireworks
(p. 63)
O
iage
Low Light
(p. 62)
Shoot with special effecs
Vivid Colors
(p. 64)
Poster Effect
(p. 64)
Fish-eye Effect
(p. 65)
Miniature Effect
(p. 65)
Toy Camera Effect
(p. 66)
Monochrome
(p. 67)
z Focus on faces ........................................................... 25, 61, 87, 94
z Shoot in places where I cannot use the flash (turn off the flash).. 26
z Take pictures with me in them too (self-timer)........................ 53, 73
z Insert the date and time into my shots.......................................... 52
z Shoot a movie clip just before taking a picture ............................. 70
z Shoot continuously at high speed................................................. 74
4
What Do You Want to Do?
1 View
z Look at my pictures ...................................................................... 28
z Automatically play back pictures (slideshow) ............................. 124
z Look at my pictures on a TV....................................................... 174
z Look at my pictures on a computer .............................................. 33
z Quickly search pictures ...................................................... 120, 121
z Erase pictures....................................................................... 29, 132
E Shoot/View Movies
z Shoot movies........................................................................ 30, 107
z View movies ................................................................................. 32
z Shoot fast moving subjects and play thm back in slow motion. 111
c
Print
z Print pictures......................................................................... 146
Save
z Save images to a computer.......................................................... 33
3
Other
z Turn off sounds............................................................................. 44
z Use the camera abroad........................................................ 16, 163
z Understand what is displayed on the screen.............................. 191
5
Checking the Package Contents .......2
Read This First ..................................3
What Do You Want to Do? ................4
Table of Contents ..............................6
Safety Precautions.............................9
Conventions Used in This Guide .....11
Returning the Camera to Default
Power Saving Function
Clock Function ................................ 48
Used Functions ................49
1
Getting Started .................13
(Digital Zoom) ............................... 50
Charging the Battery........................14
Compatible Memory Cards
(Sold Separately)...........................16
Reacquiring Zoomed In Subjects
(Zoom Framing Assist).................. 51
Inserting the Battery and
Memory Card.................................17
Inserting the Date and Time............ 52
Using the Self-Timer ....................... 53
Changing the Aspect Ratio ............. 55
Using the Screen .............................19
Setting the Display Language..........22
Pressing the Shutter Button.............2
Viewing Images ..............................28
Shooting Movies ..............................30
Viewing Movies................................32
(Image Quality) ............................. 56
Correcting the Green Tint from
Mercury Lamps ............................. 58
Adding Effects and
Transferring Images to a Computer
for Viewing.....................................33
Conditions ........................59
Take shots of moving subjects
(Sports) ......................................... 60
2
Learning More ..................37
Shooting in Special Scenes ............ 61
Components Guide..........................38
Screen Display.................................40
Adjusting the Viewfinder ..................41
FUNC. Menu – Basic Operations ....42
MENU – Basic Operations...............43
Changing the Sound Settings..........44
Adjusting the Screen Brightness......45
Indicator...........................................46
(Creative Filters) ........................... 64
Making Short Movies Automatically
(Movie Digest)............................... 70
Detecting a Face and Shooting
(Smart Shutter) ............................. 71
High-Speed Continuous Shooting
(High-speed Burst HQ) ................. 74
Shooting Stitch Assist Images......... 76
6
Table of Contents
5
Choosing Settings Yourself
...........................................77
6
Getting More Out of Your
Shooting in Program AE ................. 78
Adjusting the Brightness
(Exposure Compensation)............ 78
Setting the Shutter Speed .............102
Turning the Flash On ...................... 79
Correcting the Brightness and
Shooting (i-Contrast)..................... 79
Changing the Tone of an Image
(My Colors) ................................... 81
Shooting Movies ............107
Continuous Shooting....................... 83
Shooting Close-ups (Macro) ........... 84
Using the Digital Tele-Converter..... 85
Changing the AF Frame Mode........ 86
Changing the AF Frame Position
and Size....................................
Choosing the Subject to Focus O
Magnifying the Focal Point........... 90
Shooting with the AF Lock .............. 91
Shooting with Servo AF .................. 91
Taking Still Images while
Focus Bracketing
(Focus-BKT Mode) ....................... 92
Sound Settings..............................115
Shooting in Manual Focus Mode .... 93
Choosing the Person to Focus On
(Face Select) ................................ 94
Changing the Metering Method....... 95
Shooting with the FE Lock .............. 96
Editing Functions...........119
Auto Exposure Bracketing
(AEB Mode) .................................. 97
Quickly Searching Images.............120
Viewing Images in Filtered
Playback......................................121
Adjusting the Flash Exposure
Compensation............................... 98
Checking the Focus.......................123
Viewing Slideshows.......................124
Shooting with Slow Synchro ........... 98
Red-Eye Correction ........................ 99
7
Table of Contents
Magnifying Images.........................125
Viewing Each Image in a Group ....125
Changing Shooting Function
Registering Commonly Used Shooting
Displaying Various Images
(Smart Shuffle) ............................127
Changing Image Transitions..........128
Protecting Images..........................128
Erasing Images..............................132
Tagging Images as Favorites ........134
Organizing Images by Category
(My Category)..............................135
Viewing Images on a TV ............... 174
Rotating Images.............................138
Resizing Images ............................139
Trimming........................................140
Using the Lens Hood
(Sold Separately) ........................ 179
Using an Externally Mounted Flash
(Sold Separately) ........................ 180
Adding Effects with the My Colors
Function.......................................141
Using an Eye-Fi Card.................... 184
Correcting the Brightness
(i-Contrast)...................................142
Correcting the Red-Eye Effect.......143
9
Functions and Menu Lists ............. 196
Specifications................................ 207
Accessories................................... 211
Separately Sold Accessories ........ 212
Index ............................................. 215
Printing Images............................16
Choosing Images for Printing
(DPOF) ........................................152
10 Customizing Camera
Settings...........................157
Changing Camera Settings............158
8
Safety Precautions
• Before using the product, please ensure that you read the safety precautions described
below. Always ensure that the product is used correctly.
• The safety precautions noted on the following pages are intended to prevent injuries to
yourself and other persons, or damage to the equipment.
•
Be sure to also check the guides included with any separately sold accessories you use.
Denotes the possibility of serious injury or death.
Warning
• Do not trigger the flash in close proximity to people’s eyes.
Exposure to the intense light produced by the flash could damage eyesight. In particular,
remain at least 1 meter (39 inches) away from infants when using the flash.
• Store this equipment out of the reach of children and infants.
Strap: Putting the strap around a child’s neck could result in asphyxiation.
• Use only recommended power sources.
• Do not attempt to disassemble, alter or apply heat to the product.
• Avoid dropping or subjecting the product to severe impacts.
• To avoid the risk of injury, do not touch the interior of the product if it has been
dropped or otherwise damaged.
• Stop using the product immediately if it emits moke, a strange smell, or
otherwise behaves abnormally.
• Do not use organic solvents such as ol, bezine, or thinner to clean the
product.
•
Do not let the product come into t wh water (e.g. sea water) or other liquids.
• Do not allow liquids or foreign oto enter the camera.
This could result in electricashock or
If liquids or foreign objects come incontact with the camera interior, immediately turn
the camera off and remove the battery.
If the battery charger becomes wet, unplug it from the outlet and consult your camera
distributor or a Canon Customer Support Help Desk.
• Use only the recommended battery.
• Do not place the battery near or in direct flame.
• Unplug the power cord periodically, and using a dry cloth, wipe away any dust
and dirt that has collected on the plug, the exterior of the power outlet, and the
surrounding area.
• Do not handle the power cord with wet hands.
• Do not use the equipment in a manner that exceeds the rated capacity of the
electrical outlet or wiring accessories. Do not use if the power cord or plug are
damaged, or not fully plugged into the outlet.
• Do not allow dirt or metal objects (such as pins or keys) to contact the terminals
or plug.
The battery may explode or leak, resulting in electrical shock or fire. This could cause
injury and damage the surroundings. In the event that a battery leaks and the battery
electrolyte contacts eyes, mouth, skin or clothing, immediately flush with water.
9
Safety Precautions
• Turn the camera off in places where camera use is prohibited.
The electromagnetic waves emitted by the camera may interfere with the operation of
electronic instruments and other devices. Exercise adequate caution when using the
camera in places where use of electronic devices is restricted, such as inside airplanes
and medical facilities.
• Do not play the supplied CD-ROM(s) in any CD player that does not support data
CD-ROMs.
It is possible to suffer hearing loss from listening with headphones to the loud sounds of
a CD-ROM played on an audio CD player (music player). Additionally, this could damage
the speakers.
Denotes the possibility of injury.
Caution
• When holding the camera by the strap, be careful not to bang it, subject it to
strong impacts or shocks, or let it get caught on other objects.
• Be careful not to bump or push strongly on the lens.
This could lead to injury or damage the camera.
• When using the flash, be careful not to cover it wityour fingers or clothing.
This could result in burns or damage to the flash.
• Avoid using, placing or storing the produhe folowing places:
- Places subject to strong sunlight
- Places subject to temperatures abov(10°F)
- Humid or dusty areas
These could cause leakage, oveheating or an explosion of the battery, resulting in
electrical shock, fire, burns or otheinjuies.
High temperatures may cause deformation of the camera or battery charger casing.
• The slideshow transition effects may cause discomfort when viewed for
prolonged periods.
• When using the separately sold lens filters, be sure to attach them firmly.
If the lens becomes loose and falls off, it may crack, and the shards of glass may lead to cuts.
Denotes the possibility of damage to the equipment.
Caution
• Do not aim the camera at bright light sources (such as the sun on a clear day).
Doing so may damage the image sensor.
• When using the camera on a beach or at a windy location, be careful not to allow
dust or sand to enter the camera.
This may cause the product to malfunction.
• In regular use, small amounts of smoke may be emitted from the flash.
This is due to the high intensity of the flash burning dust and foreign materials stuck to the
front of the unit. Please use a cotton swab to remove dirt, dust or other foreign matter from
the flash to prevent heat build-up and damage to the unit.
10
Conventions Used in This Guide
• Remove and store the battery when you are not using the camera.
If the battery is left inside the camera, damage caused by leakage may occur.
• Before you discard the battery, cover the terminals with tape or other insulators.
Contacting other metal materials may lead to fire or explosions.
• Unplug the battery charger from the power outlet after charging is complete, or
when you are not using it.
• Do not place anything, such as cloth on top of the battery charger while it is
charging.
Leaving the unit plugged in for a long period of time may cause it to overheat and distort,
resulting in fire.
• Do not place the battery near pets.
Pets biting the battery could cause leakage, overheating or explosion, resulting in fire or
damage.
• When putting the camera in your bag, close the screen to face inward to ensure
that hard objects do not come into contact with the screen.
• Do not attach any hard objects to the camera.
Doing so may cause malfunctions or damage the screen.
Conventions Used in This Guide
•
•
•
Icons are used in the text to represent the camera buttons and dials.
Language that displays on the screen appears inside [ ] (square brackets).
The directional buttons, control dial and FUNC./SET button are
represented by the following icons.
FUNC./SET Button
Up Button
Right Button
Down Button
Left Button
Control Dial
•
•
•
•
•
•
•
: Things you should be careful about
: Troubleshooting tips
: Hints for getting more out of your camera
: Supplemental information
(p. xx): Reference pages (“xx” stands for a page number)
This guide assumes all functions are at their default settings.
The various types of memory cards that can be used in this camera are
collectively referred to as memory cards in this guide.
11
12
Getting Started
This chapter explains preparations before shooting, how to shoot in
A mode, and then how to view and erase the images you take. The
latter part of this chapter explains how to shoot and view movies and
transfer images to a computer.
Attaching Included Items/oldg the Camera
•
the camera during use
•
•
Attach the included lens cap cord to the strap.
Be sure to remove the lens cap before turning on the camera. Clip the lens
cap to the neck strap when not in use.
•
•
When not in use, store the camera with the lens cap attached.
Refer to p. 180 for details on the included case for the hot shoe cap.
Keep your arms tight against your body while
holding the camera firmly by the sides when
shooting. Be sure that your fingers do not
block the flash while it is raised.
13
Charging the Battery
Use the included charger to charge the battery. Be sure to charge the battery
as it is not charged at the time of purchase.
Remove the cover.
Insert the battery.
z Align the S marks on the battery and
charger, then insert the battery by sliding it
in ( ) and down ( ).
Charge the battery.
z For CB-2LC: ip out the plug ( ) and
plug thargeinto a power outlet ( ).
z For CBCE: Plug the power cord into
CB-2LC
arger, then plug the other end into a
poutlet.
X The CHARGE lamp lights and charging
starts.
CB-2LCE
X The FULL lamp will light when charging
has finished. Charging takes approx.
1 hour and 50 minutes.
Remove the battery.
z Unplug the battery charger from the power
outlet, then remove the battery by sliding it
in ( ) and up ( ).
To protect the battery and prolong its life, do not charge it for longer than
24 hours continuously.
14
Charging the Battery
Number of Possible Shots/Shooting and Playback Times
Number of Shots*1
Approx. 380
Approx. 1 hr. 20 min.
Screen On
Movie Shooting Time*2
Continuous
Shooting*3
Approx. 2 hr. 30 min.
Number of Shots
Approx. 400
Approx. 1 hr. 20 min.
Viewfinder On
Movie Shooting Time*2
Continuous
Shooting*3
Approx. 2 hr. 30 min.
Approx. 9 hr.
Playback Time
*1 The number of shots that can be taken is based on the Camera & Imaging Products
Association (CIPA) measurement standard.
*2 Times are based on default settings, starting and stopping shooting, turning the camera on
and off, and operations such as using the zoom.
*3 Times are based on repeatedly shooting until the maximum clip length is reached or recording
stops automatically.
• Under some shooting conditions, the number of posible shots and shooting time may
be less than mentioned above.
Battery Charge Indicator
An icon or message will appear screen indicating the battery’s charge
state.
Display
Summary
Sufficient charge.
Slightly depleted, but sufficient.
(Blinking red) Nearly depleted. Charge the battery.
“Change the battery pack.” Depleted. Charge the battery.
What if...
• What if the battery develops a bulge?
This is a normal characteristic of the battery and does not indicate a problem.
However, if the battery bulges to the point where it will no longer fit into the
camera, please contact a Canon Customer Support Help Desk.
• What if the battery is quickly depleted even after charging?
The battery has reached the end of its life span. Purchase a new battery.
15
Compatible Memory Cards (Sold Separately)
Using the battery and charger effectively
• Charge the battery on the day, or the day before, it will be
used.
Charged batteries continue to discharge naturally even if
they are not used.
Attach the cover to a charged battery so that the S mark
is visible.
• How to store the battery for long periods:
Deplete and remove the battery from the camera. Attach the terminal cover and
store the battery. Storing a battery for long periods of time (about a year) without
depleting it may shorten its life span or affect its performance.
• The battery charger can also be used when abroad.
The charger can be used in regions that have 100 – 240 V (50/60 Hz) AC power.
If the plug does not fit the outlet, use a commercially available plug adapter. Do
not use electrical transformers for foreign travel as they will cause damage.
Compatible Memory Card
(Sold Separately)
The cards below can be used withtrictions on their capacities.
•
•
•
•
SD memory cards*
SDHC memory cards*
SDXC memory cards*
Eye-Fi cards
* This memory card complies with SD standards. Some cards may not operate properly
depending on the brand of card used.
Depending on your computer’s OS version, SDXC memory cards may not
be recognized even when using a commercially available card reader.
Check to make sure that your OS supports SDXC memory cards
beforehand.
About Eye-Fi Cards
This product is not guaranteed to support Eye-Fi card functions (including
wireless transfer). In case of an issue with an Eye-Fi card, please check with
the card manufacturer.
Also note that an approval is required to use Eye-Fi cards in many countries
or regions. Without approval, use of the card is not permitted. If it is unclear
whether the card has been approved for use in the area, please check with
the card manufacturer.
16
Inserting the Battery and Memory Card
Insert the included battery and a memory card (sold separately).
Check the card’s write-protect tab.
z If the memory card has a write-protect tab,
you will not be able to record images if the
tab is in the locked position. Slide the tab
up until you hear a click.
Open the cover.
z Slide the cover ( ) and open it ( ).
Insert the battery.
z Insert the battery as shown until it locks
into place wth a click.
z Be e to isert the battery in the correct
diren or it will not properly lock into
ce
Terminals
Insert the memory card.
z Insert the memory card as shown until it
locks into place with a click.
z Be sure the memory card is oriented
correctly. Inserting the memory card in the
wrong direction could damage the camera.
Label
Close the cover.
z Close the cover ( ), and press downward
as you slide it until it clicks into place ( ).
What if [Memory card locked] appears on the screen?
If the write-protect tab is in the locked position, [Memory card locked] will appear
on the screen and you will not be able to take or erase images.
17
Inserting the Battery and Memory Card
Removing the Battery and Memory Card
Remove the battery.
z Open the cover and press the battery lock
in the direction of the arrow.
X The battery will pop up.
Remove the memory card.
z Push the memory card in until you hear a
click, then slowly release it.
X The memory card will pop up.
Number of Shots per Memory Card
Memory Card
4 GB
16 GB
Number of Shots
Approx. 123
Approx. 5042
• Values are based on the default settings.
subject and the memory card used.
Can you check the umer of shots that can be taken?
You can check the number of shots that can be
taken when the camera is in a Shooting mode
(p. 25).
18
Using the Screen
Open the screen.
z Open the screen ( ), and rotate it forward
(toward the lens) 180° ( ).
z Close the screen ( ).
Adjusting the Position of the Screen
Approx. 180°
z You can adjust the angle and orientation of
the screen for the shooting conditions.
z To protect the screen, always keep it
closed, facing the camera body when the
camera is not in use.
Approx. 90°
Approx.
175°
• When the camera is on, opening the sceen will turn the screen on and
the viewfinder off. Closing the screen o faces the camera body will turn
the screen off and the viewfind.
• In a Shooting mode, if the creeopened and rotated toward the lens,
the image will be flipped eft o right (mirror image). To cancel the
reverse display function, he n button to choose [Reverse
Disp.] in the 4 tab, then press the qr buttons to choose [Off].
19
Setting the Date and Time
The Date/Time settings screen will appear the first time the camera is turned
on. Since the dates and times recorded into your images are based on these
settings, be sure to set them.
Turn on the camera.
z Press the power button.
X The Date/Time screen will appear.
Set the date and time.
z Press the qr buttons to choose an option.
z Press the op buttons or turn the 5 dial
to set a value.
z Once all settings are complete, press the
m button.
Set the home time zone.
z Press the qr buttons or turn the 5 dial to
choose your home time zone.
Complete the setting.
z Press the m button to complete the
setting. After a confirmation screen
appears, the shooting screen will
reappear.
z Pressing the power button will turn off the
camera.
Reappearing Date/Time screen
Set the correct date and time. If you have not set the date and time and the home
time zone, the Date/Time screen will appear each time you turn on the camera.
20
Setting the Date and Time
Daylight saving time settings
If you choose
dial to choose
in Step 2 on p. 20 and press the op buttons or turn the 5
, you will set the time to daylight saving (1 hour ahead).
Changing the Date and Time
You can change the current date and time settings.
Display the menu.
z Press the n button.
Choose [Date/Time].
z Move the zom lever to choose the 3 tab.
z Press the p buttons or turn the 5 dial
to se [Date/Time], then press the m
utt
Change the date and time.
z Follow Steps 2 – 3 on p. 20 to adjust the
settings.
z Press the n button to close the menu.
the date/time settings to be retained for about 3 weeks after the battery
pack has been removed.
• By inserting a charged battery or connecting an AC adapter kit (sold
separately, p. 212) the date/time battery can be charged in about 4 hours
even if the camera is not turned on.
• If the date/time battery is depleted, the Date/Time screen will appear
when you turn the camera on. Follow the steps on p. 20 to set the date
and time.
21
Setting the Display Language
You can change the language that displays on the screen.
Enter Playback mode.
z Press the 1 button.
Display the settings screen.
z Press and hold the m button, then
immediately press the n button.
Set the display language.
z Press the opqr buttons or turn the 5
dial to choose a language, then press the
m button.
X Once thdisply language has been set,
the setscren will close.
What if the clock appears when the m button is pressed?
The clock will appear if too much time passes between pressing the m button
and the n button in Step 2. If the clock appears, press the m button to
remove the clock and repeat Step 2.
You can also change the display language by pressing the n button
to choose [Language
] in the 3 tab.
22
Formatting Memory Cards
Before you use a new memory card or one that has been formatted in other
devices, you should format the card with this camera.
Formatting (initializing) a memory card erases all data on the memory card.
As you cannot retrieve the erased data, exercise adequate caution before
formatting the memory card.
Before formatting an Eye-Fi card (p. 184), be sure to install the software
contained on the card to a computer.
Display the menu.
z Press the n button.
Choose [Format].
z Move the zoom lever to choose the 3 tab.
5
m
z Press the op buttons or turn the
to choose [ormat], then press the
button.
dial
Choose [OK].
z Press the qr buttons or turn the 5 dial to
choose [OK], then press the m button.
Format the memory card.
z Press the op buttons or turn the 5 dial
to choose [OK], then press the m button
to start formatting.
z When formatting ends, [Memory card
formatting complete] appears on the
screen. Press the m button.
23
Pressing the Shutter Button
Formatting or erasing data on a memory card merely changes the file
completely erased. Be careful when transferring or disposing of a memory
card. When disposing of a memory card, take precautions such as
physically destroying the card to prevent personal information leaks.
• The total capacity of the memory card displayed in the formatting screen
may be less than indicated on the memory card.
• Perform a low-level format (p. 159) of the memory card when the camera
does not operate properly, the recording/reading speed of a memory card
has dropped, when continuous shooting speed slows down, or when
movie recording stops suddenly.
Pressing the Shutter Button
To take images that are in focus, be sure to first press the shutter button
lightly (halfway) to focus, then press fully to shoo.
Press hway (Press lightly to focus).
z ligtly until the camera beeps twice
aframes appear where the camera
focused.
Press fully (Press fully to shoot).
X The camera plays the shutter sound and
takes the shot.
z Since the shot is being taken while the
shutter sound plays, be careful not to move
the camera.
Does the length of the shutter sound change?
• Since the time required to shoot differs depending on the scene you want to
take, the length of the shutter sound may change.
• If the camera or subject moves while the shutter sound is playing, the recorded
image may be blurry.
If you shoot without pressing the shutter button halfway, the image may not
be in focus.
24
Taking Pictures (Smart Auto)
Since the camera can determine the subject and shooting conditions, you can
let it automatically select the best settings for the scene and just shoot. When
the flash fires, the white balance of the main subject and background will be
automatically adjusted to obtain the best color (Multi-area White Balance).
Turn on the camera.
z Press the power button.
X The start-up screen will appear.
Enter A mode.
z When you point the camera toward the
subject, the camera will make a slight
noise as it determines the scene.
X The icon fothe determined scene, and the
IS mde icn will appear on the screen
(pp, 193.
e cmera will focus on detected
jects and display frames on them.
Compose the shot.
z Moving the zoom lever toward i
(telephoto) will zoom in on your subject,
making it appear larger. Moving the lever
toward j (wide angle) will zoom out from
Focus Range (approx.)
your subject, making it appear smaller.
Zoom Bar
(The zoom bar showing the zoom position
appears on the screen.)
z If you move the zoom lever all the way
toward i (telephoto) or j (wide angle),
the camera will zoom in or out quickly. If
you move the zoom lever slightly, it will
zoom in or out slowly.
25
Taking Pictures (Smart Auto)
Focus.
z Press the shutter button halfway to focus.
X When the camera focuses, it will beep
twice and AF frames will appear where the
camera focused.
Several AF frames will appear when the
camera focuses on more than 1 point.
AF Frame
z If [Raise the flash] appears on the screen,
raise the flash manually to use it. If you
manually lowethe flash until it closes, it
will not fire.
Sh
z Prthe shutter button fully to shoot.
X The camera will play the shutter sound and
shoot. The flash will automatically fire in
low light conditions if it is raised.
X The image will appear on the screen for
approximately 2 seconds.
z You can take a second picture even while
an image is displayed by pressing the
shutter button again.
What if...
• What if the color and brightness of the images do not turn out as
expected?
The scene icon (p. 192) that appears on the screen may not match the actual
scene, and you may not obtain the expected results. If this happens, try
shooting in G mode (p. 77).
• What if the screen is off even when the camera is turned on?
The display is set to the viewfinder. Press the l button several times to
restore the display to the screen.
26
Taking Pictures (Smart Auto)
• What if white and gray frames appear when you point the camera toward
a subject?
A white frame appears on the face or subject that the camera detected as the
main subject, while gray frames appear on other detected faces. The frames will
follow the subjects within a certain range.
If the subject moves, however, the gray frames will disappear, leaving only the
white frame.
• What if a frame does not appear on the subject you want to shoot?
The subject may not be detected, and frames may appear on the background.
If this happens, try shooting in G mode (p. 77).
• What if a blue frame appears when you press the shutter button halfway?
A blue frame appears when a moving subject is detected; the focus and
exposure will continuously adjust (Servo AF).
• What if a flashing
appears?
Attach the camera to a tripod so that the camera does not move and blur the
image.
• What if the camera does not play any sounds?
You may have been pressing the l butowhile turning on the camera,
which will turn off all sounds. To turn thoundon, press the n button to
choose [Mute] in the 3 tab, then presqr buttons to choose [Off].
• What if the image comes out evn if the flash fired when shooting?
The subject is too far away for h to reach. The effective flash range is
approximately 50 cm – 0 m (1.6 – 23 ft.) at maximum wide angle (j), and
approximately 1.4 – 3.0 m (4.6 – 9.8 ft.) at maximum telephoto (i).
• What if the camera beeps once when the shutter button is pressed
halfway?
Your subject may be too close. Move about 1.4 m (4.6 ft.) or more away when
the camera is at maximum telephoto (i).
• What if the lamp lights when the shutter button is pressed halfway?
To reduce red-eye and to assist in focusing, the lamp may light when shooting
in low light conditions.
The flash is charging. You can shoot when recharging ends.
What if an icon appears on the screen?
The icon for the determined scene, and the IS mode icon will appear on the
screen. For details on the icons that appear, see “Scene Icons” (p. 192) and “IS
Mode Icons” (p. 193).
27
Viewing Images
Choosing the subject to focus on (Tracking AF)
After pressing the o button and displaying
, point the camera so that
is
on the subject you want to focus on. Press and hold the shutter button halfway to
display a blue frame where focus and exposure will be maintained (Servo AF).
Press the shutter button fully to shoot.
Viewing Images
You can view the images you have taken on the screen.
Enter Playback mode.
z Press the 1 button.
X The last image you took will appear.
Choose an image.
z Pressine q button or turning the 5
uner-clockwise will cycle through
tges from newest to oldest.
z Pressing the r button or turning the 5
dial clockwise will cycle through the
images from oldest to newest.
z The images change more quickly if you
keep the qr buttons pressed, but they will
appear coarse.
z The lens will retract after approximately 1
minute elapses.
z Pressing the 1 button again while the
lens is retracted will turn the camera off.
Switching to Shooting mode
Pressing the shutter button halfway while in Playback mode switches the camera
to Shooting mode.
28
Erasing Images
You can choose and erase images one at a time. Please note that erased
images cannot be recovered. Exercise adequate caution before erasing an
image.
Enter Playback mode.
z Press the 1 button.
X The last image you took will appear.
Choose an image to erase.
z Press the qr buttons or turn the 5 dial to
display an image to erase.
Erase the image.
z Press the a button.
z When [Erase?] appears on the screen,
press the qr buttons or turn the 5 dial to
choose [Erase], then press the m button.
X The displayed image will be erased.
z To exit instead of erasing, press the qr
buttons or turn the 5 dial to choose
[Cancel], then press the m button.
29
Shooting Movies
The camera will determine the subject and shooting conditions, and select the
best settings for the scene. The audio will record in stereo.
Remaining Time
Set the camera to A mode and
compose the shot.
z Follow Steps 1 – 3 on p. 25 to compose the
shot.
z You can check the remaining shooting
time on the screen.
Shoot.
z Press the movie button.
z Black bars appear at the top and bottom of
the screen. These areas cannot be
recorded.
Elapsed Time
X mra will beep once, recording will
snd [ Rec] and the elapsed time will
appear on the screen.
z Once shooting begins, take your finger off
the movie button.
z If you change the composition of your shot
during shooting, the focus, brightness and
tone will automatically adjust.
z Do not touch the microphones while
shooting.
z Do not press any buttons other than the
movie button while shooting. The sound
Microphones
the buttons make will be recorded in the
movie.
30
Shooting Movies
Stop shooting.
z Press the movie button again.
X The camera will beep twice and stop
shooting the movie.
X Shooting will automatically stop when the
memory card fills.
What if white and gray frames appear when shooting?
A white frame appears on the face that the camera detected as the main subject,
while gray frames appear on other detected faces. The frames will follow the
subjects within a certain range.
Zooming while shooting
Moving the zoom lever while shooting will zoom in on or out from the subject.
However, operation sounds will be recorded.
• When the mode dial is set to Athe in for the determined scene will
certain conditions, the ict apears may not match the actual scene.
optimal, press the movie bn to stop recording, then start recording
again (only when te imge quality is set to
(p. 113)).
• Movies can be shot by pressing the movie button even when the mode
dial is in positions other than A (p. 107).
• When the mode dial is set to E, you can adjust each setting for shooting
movies (p. 107).
Shooting Time
Memory Card
Shooting Time
4 GB
16 GB
Approx. 14 min. 34 sec.
Approx. 59 min. 40 sec.
• Shooting times are based on default settings.
• Maximum clip length is approx. 29 min. 59 sec.
• Recording may stop even if the maximum clip length has not been reached on some
memory cards. SD Speed Class 6 or higher memory cards are recommended.
31
Viewing Movies
You can view the movies you have shot on the screen.
Enter Playback mode.
z Press the 1 button.
X The last image you took will appear.
X
appears on movies.
Choose a movie.
5
m
z Press the qr buttons or turn the
dial to
button.
choose a movie, then press the
X The movie control panel will appear.
Plae movie.
z Press the qr buttons or turn the 5 dial to
choose
X The movie will play.
, then press the m button.
z Press the op buttons to adjust the
volume.
z If you press the m button, you can pause
or resume playback.
X After the movie finishes,
appears.
32
Transferring Images to a Computer for Viewing
How can I play back movies on a computer?
Install the included software (p. 34).
• When watching a movie on a computer, frames may drop, it may not play
smoothly, and the audio may stop suddenly depending on the computer’s
capabilities. Use the supplied software to copy the movie back onto the memory
card, then play back the movie with the camera. If you connect the camera to a
TV, you can view images on the larger screen.
Transferring Images to a Computer for
Viewing
You can use the included software to transfer images you have shot with the
camera to a computer for viewing. If you are already using software included
with another Canon-brand compact digital camera, install the software from
the included CD-ROM, overwriting your curret installation.
System Requirements
Windows
Windos 7 (Icluding Service Pack 1)
Windows Vita SP2
Windows XP SP3
OS
The above OS should be pre-installed on computers with built-in
USB ports.
Computer Model
CPU
Pentium 1.3 GHz or higher (still images), Core 2 Duo 2.6 GHz or
higher (movies)
Windows 7 (64 bit): 2 GB or more
Windows 7 (32bit), Windows Vista (64bit, 32bit): 1GB or more (still
images), 2 GB or more (movies)
RAM
Windows XP: 512 MB or more (still images), 2 GB or more
(movies)
Interface
USB
Free Hard Disk
Space
420 MB or more*
1024 x 768 pixels or higher
Display
* For Windows XP, Microsoft .NET Framework 3.0 or later (max. 500 MB) must be installed.
Installation may take some time depending on your computer’s capabilities.
33
Transferring Images to a Computer for Viewing
Macintosh
Mac OS X v10.5 - v10.6
OS
The above OS should be pre-installed on computers with built-in
USB ports.
Computer Model
Intel Processor (still images)
Core 2 Duo 2.6 GHz or higher (movies)
CPU
Mac OS X v10.6: 1 GB or more (still images), 2 GB or more
(movies)
RAM
Mac OS X v10.5: 512 MB or more (still images), 2 GB or more
(movies)
USB
Interface
Free Hard Disk
Space
480 MB or more
1024 x 768 pixels or higher
Display
Installing the Software
Windows Vista and Mac OS X (v10.5) are ed fthese explanations.
Plhe CD-ROM in the
comer’s CD-ROM drive.
z Place the supplied CD-ROM (DIGITAL
CAMERA Solution Disk) (p. 2) into the
computer’s CD-ROM drive.
z When the CD-ROM is placed in a
Macintosh, a CD-ROM icon will appear on
the desktop. Double-click the icon to open
the CD-ROM, then double click
it appears.
when
Install the software.
z For Windows, click [Easy Installation], and
for Macintosh click [Install], then follow the
on-screen instructions to proceed with the
installation.
z If the [User Account Control] window
appears in Windows, follow the on-screen
instructions to proceed.
34
Transferring Images to a Computer for Viewing
Complete the installation.
z For Windows, click [Restart] or [Finish],
then remove the CD-ROM when your
desktop screen appears.
z For Macintosh, click [Finish] in the screen
that appears when the installation is
complete, then remove the CD-ROM when
your desktop screen appears.
Transferring and Viewing Images
Connect the camera to the
computer.
z Turn off the camera.
z Open the cover and insert the included
interface cble’s smaller plug (p. 2) firmly
intcamra terminal in the direction
ho.
ert he interface cable’s larger plug into
computer’s USB port. For details on
the computer’s USB port, refer to the user
guide provided with the computer.
Turn on the camera to open
CameraWindow.
z Press the 1 button to turn on the camera.
z For Windows, click [Downloads Images
From Canon Camera using Canon
CameraWindow] when it appears on the
screen. CameraWindow will appear when
a connection is established between the
camera and computer.
z For Macintosh, CameraWindow will
appear when a connection is established
between the camera and computer.
35
Transferring Images to a Computer for Viewing
CameraWindow
Transfer Images.
z Click [Import Images from Camera], and
then click [Import Untransferred Images].
X Images will transfer to the computer.
Images will be sorted by date and saved in
separate folders in the Pictures folder.
z When image transfer is complete, close
CameraWindow and press the 1 button
to turn the camera off, then unplug the
cable.
z For details on how to view images using a
computer, refer to the Software Guide.
• If CameraWindow does not appear even after following Step 2 for
Windows, click the [Start] menu and choose [All Programs], followed by
[Canon Utilities], [CameraWindow] and [CameraWindow].
• If CameraWindow does not appear even ar following Step 2 for
Macintosh, click the CameraWindn on he Dock (the bar which
appears at the bottom of the kto
• For Windows 7, use the follteps to display CameraWindow.
Click
on the tak bar.
In the screen that apeas, click the
link to modify the program.
Choose [Downloads Images From Canon Camera using Canon
CameraWindow] and click [OK].
Double click
.
• You can transfer images even without using the image transfer function
in the included software by simply connecting your camera to a computer.
There are, however, the following limitations.
- It may take a few minutes from when you connect the camera to the computer
until you can transfer images.
- Images shot in the vertical orientation may be transferred in the horizontal
orientation.
- Protection settings for images may be lost when transferred to a computer.
- There may be problems transferring images or image information correctly
depending on the version of the operating system in use, the file size, or the
software in use.
- Some functions in the included software may not be available, such as editing
movies, and transferring images to the camera.
36
Components Guide
Zoom Lever
Angle) (pp. 25, 50)
(pp. 120, 125)
h (Flash) Button (pp. 79, 98)
Speaker
Lamp (pp. 53, 71, 72, 73, 165, 166)
Focal Lngth (approx.)
ns
Shutter Button (p. 24)
Strap Mount (p. 13)
Mode Dial
s Hoo/Filter Adapter Mount
. 179)
Trpod Socket
Flash (pp. 26, 79)
Hot Shoe Cap (p. 180)
Microphones (p. 30)
Memory Card / Battery Cover (p. 17)
DC Coupler Cable Port (p. 178)
Mode Dial
Use the mode dial to change the Shooting mode.
Movie Mode
P, Tv, Av, M, C1, C2 Mode
Choose settings yourself to take
various types of pictures (p. 78).
For shooting movies
(p. 108).
Even if the mode dial is
set to a position other
than Movie mode,
movies can be shot by
pressing the movie
button (p. 109).
Auto Mode
You can leave it to the
camera to select settings for
fully automatic shooting
(pp. 25, 30).
Creative Filters Mode
Scene Mode
You can add various effects to
images when shooting (p. 64).
You can shoot with the optimum
settings for the scene (p. 60).
38
Components Guide
Screen (LCD Monitor)
(AF Frame Selector) (p. 88) /
(pp. 19, 40, 191, 194)
(Short Cut) (p. 170) /
l (Display) Button (pp. 27, 40)
c (Direct Print) Button (p. 146)
Diopter Adjustment Dial (p. 41)
Viewfinder (p. 40)
b (Exposure Compensation) (p. 78) /
Movie Button (pp. 30, 107)
Indicator (p. 46)
(p. 81) / r Button
Power Button (p. 20)
m FUNC./SET Button (p. 42)
Q (Self-Timer) (pp. 53, 54) / p Button
Control Dial
(Zoom Framing Assis(p. 5) /
d (Jump) Button (p. 121)
HDMI™ Terminal (p. 175)
1 (Playback) Button (pp. 28, 119)
A/V OUT (Audio/Video Output) /
DIGITAL Terminal (pp. 35, 174, 146)
Control Dial
z Turning the control dial allows you to
perform operations such as choosing
items or switching images. Except for a
few operations, the same operations are
possible with the opqr buttons.
39
Screen Display
Switching the Display
You can change the screen display using the l button. Refer to p. 191
for details on information that appears on the screen.
Opening the screen with the camera on will turn the screen on, and turn the
viewfinder off. Closing the screen so that it faces inward will turn the screen
off, and turn the viewfinder on (p. 19).
Shooting
LCD Monitor (Screen)
Viewfinder
Display 1
Display 2
Display 1
Display 2
Playback
No Information
Display
Simple Information
Display
Detailed
Information Display
Focus Check
Display (p. 123)
You can also switch the display by pressing the l button while the
image displays right after shooting. However, Simple Information Display is
not available. You can change the display that appears first by pressing the
n button, then choosing [Review info] in the 4 tab (p. 167).
40
Adjusting the Viewfinder
Screen Display in Low Light Conditions
The display automatically brightens when shooting in low light conditions,
allowing you to check the composition (Night Display function). However, the
recorded may be different. Screen noise may appear and the movement of
the subject may appear somewhat rough on the screen. This has no effect on
the recorded image.
Overexposure Warning during Playback
In Detailed Information Display (p. 40), overexposed areas of the image flash
on the screen.
Histogram during Playback
z The graph that appears in Detailed
Information Display (p. 194) is called the
distribution of brightness in an image
horintallyand the amount of brightness
verty, and in this way you can judge
eposure.
High
Low
Dark
Bright
histogram can also be displayed while
shooting (pp. 167, 191).
Adjusting the Viewfinder
You can adjust the viewfinder so that the display is clearly visible (Dioptric
adjustment).
Switch to the viewfinder display.
z Press the l button several times until
the viewfinder turns on (p. 40).
Adjust the diopter.
z Adjust the dial while looking through the
viewfinder.
-1
z Adjustments of -4.0 to +1.0 m (dpt) can
be made.
41
FUNC. Menu – Basic Operations
Commonly used functions can be set with the FUNC. menu.
The menu items and options differ depending on the Shooting mode (pp. 198
– 199).
Display the FUNC. menu.
z Press the m button.
Choose a menu item.
z Press the op buttons to choose a menu
item.
X The available options for the menu item
appear in the lower part of the screen.
Choose an option.
z Press the qr ttons or turn the 5 dial to
Available Options
choosoptio.
Menu Items
z an lso choose settings by pressing
tl button on options that display
z To return to the menu items, press the
l button.
Complete the setting.
z Press the m button.
X The shooting screen will reappear and the
setting you chose will display on the
screen.
42
MENU – Basic Operations
Various functions can be set from the menus. The menu items are organized
under tabs, such as for shooting (4) and playback (1). The options differ
depending on the Shooting mode and the Playback mode (pp. 200 – 203).
Display the menu.
z Press the n button.
Choose a tab.
z Move the zoom lever or press the qr
buttons to choose a tab.
Choose an item.
z Press the op buttons or turn the 5 dial
to choose n item.
z Some itemrequire you to press the m or
r bn to dsplay a submenu in which
u cange the setting.
Choose an option.
z Press the qr buttons to choose an option.
Complete the setting.
z Press the n button to restore the
normal screen.
43
Changing the Sound Settings
You can silence or adjust the volume of camera sounds.
Muting Sounds
Display the menu.
z Press the n button.
Choose [Mute].
z Move the zoom lever to choose the 3 tab.
z Press the op buttons or turn the 5 dial
to choose [Mute], then press the qr
buttons to choose [On].
z Press the n button to restore the
normal screen
• You can also mute camera sounds by holding down the l button and
turning the camera on.
• If you mute camera sounds, the sound will also be muted when playing
back movies (p. 32). If you press the o button while playing back a
movie, the sound will play back, and you can adjust the volume with the
op buttons.
Adjusting the Volume
Display the menu.
z Press the n button.
44
Adjusting the Screen Brightness
Choose [Volume].
z Move the zoom lever to choose the 3 tab.
5
z Press the op buttons or turn the
dial
to choose [Volume], then press the
m
button.
Adjust the volume.
z Press the op buttons or turn the 5 dial
to choose an item, then press the qr
buttons to djust the volume.
z Pre n button twice to restore
e nrmal screen.
Adjusting the Screen Brightness
The screen brightness can be adjusted in 2 ways.
You can set the brightness of the screen and the viewfinder separately (Press
the l button to switch to the desired display before making settings).
Using the Menu
Display the menu.
z Press the n button.
45
Indicator
Choose [LCD Brightness].
z Move the zoom lever to choose the 3 tab.
z Press the op buttons or turn the 5 dial
to choose [LCD Brightness].
Adjust the brightness.
z Press the qr buttons to adjust the
brightness.
z Press the n button twice to restore
the normal screen.
Using the l Button
z Press and hold the l button for more
than 1 second
X The screen ineases to maximum
brightn(The ettings made in [LCD
Btnes] in the 3 tab will be disabled).
z and hold the l button again for
mhan 1 second to return the screen to
he original brightness.
• The next time you turn on the camera, the screen will be at the brightness
setting chosen in the 3 tab.
• When you have [LCD Brightness] set to its highest setting in the 3 tab,
you cannot adjust the brightness with the l button.
Indicator
The indicator on the back of the camera (p. 39) will light or blink depending
on the camera’s status.
Color
Status
Operation Status
Lights Camera on
Green
Blinks During camera start-up, recording/reading/transmitting image data
When the indicator blinks green, do not turn the camera off, open the
memory card slot/battery cover, shake or jolt the camera. These actions
may corrupt the image data or cause the camera or memory card to
malfunction.
46
Returning the Camera to Default Settings
When you have mistakenly changed a setting, you can reset the camera to
the default settings.
Display the menu.
z Press the n button.
Choose [Reset All].
z Move the zoom lever to choose the 3 tab.
z Press the op buttons or turn the 5 dial
to choose [Reset All], then press the m
button.
Reset the settings.
z Press the qr buttons or turn the 5 dial to
choose [OK], then press the m button.
settings.
Are there functions that cannot be reset?
• The [Date/Time] (p. 21), [Language
] (p. 22), the image registered in [Start-
up Image] (p. 160), [Time Zone] (p. 163) and [Video System] (p. 174) in the 3
tab.
• The Shooting mode chosen in K (p. 61) or
(p. 64).
• Colors that were chosen in Color Accent (p. 67) or Color Swap (p. 68).
• The recorded custom white balance data (p. 80).
• The Movie mode (p. 108).
47
Power Saving Function
(Auto Power Down)
To save battery power, the screen turns off, and the camera turns off
automatically when it is not operated for a certain time.
Power Saving during Shooting
The screen will turn off approximately 1 minute after you stop operating the
camera. After about 2 more minutes, the lens will retract and the camera will
turn off. When the screen has turned off but the lens has not yet retracted,
can continue.
Power Saving during Playback
The camera will turn off approximately 5 minutes after you stop operating the
camera.
• You can turn off the power saving function (p. 162).
• You can adjust the time before the screen trns off (p. 163).
Clock Function
You can check the current time.
z Press and hold the m button.
X The current time appears.
z If you hold the camera vertically while
using the clock function, it will switch to
vertical display. Press the qr buttons or
turn the 5 dial to change the display
color.
z Press the m button again to cancel the
clock display.
When the camera is off, press and hold the m button, then press the
power button to display the clock.
48
Zooming In More Closely on Subjects
(Digital Zoom)
You can use the digital zoom to zoom up to approximately 140x maximum,
and capture subjects that are too far away for the optical zoom to enlarge.
Move the zoom lever toward i.
z Hold the lever until zooming stops.
X Zooming stops at the largest possible
zoom factor without image deterioration.
The zoom factor will appear on the screen
when you release the zoom lever.
Zoom Factor
Move the zoom lever toward i
again.
X The digital zoom will zoom in even further
on the subject.
Turning off the digtal zoo
To turn off the digital zoom, press te n button to choose [Digital Zoom] in
the 4 tab, then choose [Off].
• The focal lengths when using the optical zoom and digital zoom together
are as follows (all focal lengths are 35mm film equivalent):
24 – 3360 mm (24 – 840 mm when using the optical zoom alone)
• Depending on the recording pixel setting (p. 56) and zoom factor, the
images may appear coarse (the zoom factor will appear in blue).
50
Reacquiring Zoomed In Subjects
(Zoom Framing Assist)
If you lose track of your subject while zoomed in, temporarily zooming out will
make it easier to find.
Look for the subject.
z Press and hold the
button.
X The camera will zoom out, and a white
frame will appear on the area displayed
before pressing the
button.
Reacire he subject.
lache subject inside the white frame
reease the
button.
X e camera will return to the original zoom
position.
Changing the displayed area when pressing the
button
Press the n button to choose [
from 3 levels.
Display Area] in the 4 tab, then choose
• While the camera is zoomed out, some shooting information will not
appear on the screen.
• If you press the shutter button fully while in the screen in Step 1, you can
shoot at that zoom factor.
• While shooting a movie, the white frame will not appear even if you press
the
button. The sound of the camera zooming out and any operation
sounds will be recorded.
• Zoom Framing Assist is not available after fully pressing the shutter
button when using the self-timer (p. 53),
shooting in mode is not available while pressing the
or
. In addition, automatic
button.
51
Inserting the Date and Time
You can insert the shooting date and time in the lower right corner of an
image. Once inserted, however, they cannot be deleted. Be sure to check
beforehand that the date and time are correctly set (p. 20).
Display the menu.
z Press the n button.
Choose [Date Stamp].
z Move the zoom lever to choose the 4 tab.
z Press the op buttons or turn the 5 dial
to choose [Date Stamp].
Choose the setting.
z Press the qr uttons to choose [Date] or
[Date & Time.
z Press n button to complete the
g ad restore the shooting screen.
X et, [DATE] will appear on the
scren.
Shoot.
X The shooting date or time will be recorded
in the image’s lower right corner.
z To restore the original setting, choose [Off]
in Step 3.
embedded date and time as follows. However, if you do this for images with
an embedded date and time, the date and time may be printed twice.
• Use the DPOF print settings (p. 152) to print.
• Use the included software to print.
Refer to the Software Guide for details.
• Print using printer functions (p. 146).
52
Using the Self-Timer
The self-timer can be used to shoot a group photo that includes the
photographer. The camera will shoot approximately 10 seconds after the
shutter button is pressed.
Choose ].
z After pressing the p button, press the
op buttons or turn the 5 dial to choose
], then press the m button.
X Once set, ] will appear on the screen.
Shoot.
z Pree shutter button halfway to focus
thsubject, then press it fully.
en the self-timer starts, the lamp blinks
and the self-timer sound plays.
X Two seconds before the shutter releases,
the lamp and sound speed up (the lamp
remains lit when the flash will fire).
z To cancel shooting with the self-timer after
the countdown has started, press the
n button.
z To restore the original setting, choose
in Step 1.
53
Using the Self-Timer
Using the Self-Timer to Prevent Camera Shake
The camera will shoot approximately 2 seconds after the shutter button is
button.
Choose [.
z Follow Step 1 on p. 53 to choose [.
X Once set, [ will appear on the screen.
z Follow Step 2 on p. 53 to shoot.
Customizing the Self-Timer
You can set the delay (0 – 30 seconds) and the umber of shots (1 – 10
shots).
Che $.
z FStep 1 on p. 53 to choose $, then
ress the n button immediately.
Choose the settings.
z Press the op buttons to choose [Delay]
or [Shots].
5
z Press the qr buttons or turn the
choose a value, then press the
dial to
button.
m
X Once set, $ will appear on the screen.
z Follow Step 2 on p. 53 to shoot.
54
Changing the Aspect Ratio
• When 2 or more shots are set, the exposure and white balance settings
are set with the first shot. If the flash fires or you set a high number of
shots, the shooting interval may take longer than usual. Shooting will stop
automatically if the memory card fills.
• When you set the delay for more than 2 seconds, the lamp and self-timer
sound speed up 2 seconds before the shutter releases (the lamp remains
lit when the flash will fire).
Changing the Aspect Ratio
You can change the width to height ratio of an image.
Choose
.
z After pressing the m button, press the
op buttons to choose
.
Choose an option.
z Pree qr buttons or turn the 5 dial to
oose an option, then press the m
on.
X Once set, the aspect ratio of the screen will
change.
z To restore the original setting, choose
in Step 2.
The same aspect ratio as HD TVs, used for displaying on wide-screen HD TVs.
The same aspect ratio as 35mm film, used for printing out 5 x 7 in. or postcard
sized images.
The same aspect ratio as the screen of this camera, used for printing images on
3.5 x 5 in. to various A-sized papers.
A square-shaped aspect ratio.
In
and
aspect ratios, [Digital Zoom] (p. 50) is fixed to [Off], and is
not available.
55
Changing the Recording Pixel Setting
(Image Size)
You can choose from 4 recording pixel settings.
Choose the recording pixel setting.
z After pressing the m button, press the
op buttons to choose
.
Choose an option.
5
m
z Press the qr buttons or turn the
dial to
choose an option, then press the
button.
X The setting will appear on the screen.
z To restore the original setting, choose
in Steps 1 – 2.
The digital zoom can be used in the following aspect ratio and recording
pixel setting combinations:
Aspect ratios of
or
in a recopixel setting of
An aspect ratio of
in all othrecong pixel settings
Changing the Compssion Ratio
(Image Quality)
You can choose from the following 2 compression ratios (image quality):
(Fine),
(Normal).
Choose the compression ratio
setting.
z After pressing the m button, press the
op buttons to choose
, then press the
l button.
Choose an option.
5
m
z Press the qr buttons or turn the
choose an option, then press the
button.
dial to
X The setting will appear on the screen.
z To restore the original setting, choose
in Steps 1 – 2.
56
Changing the Compression Ratio (Image Quality)
Approximate Values for Recording Pixels and Compression
Ratio (for 4:3 Aspect Ratios)
Number of Shots per
Single Image
Memory Card
Compression
Ratio
Recording Pixels
Data Size
(Approx. KB)
(Approx. shots)
4 GB
16 GB
(Large)
12M/4000x3000
(Medium 1)
3084
1474
1620
780
558
278
150
84
1231
2514
5042
10295
9503
2320
6M/2816x2112
(Medium 2)
4641
19007
26010
49420
82367
123550
6352
2M/1600x1200
(Small)
12069
20116
30174
0.3M/640x480
• The values in the table are measured according to Canon standards and may change
depending on the subject, memory card and caesettings.
• The values in the table are based on 4:3 t rati. If the aspect ratio is changed
(p. 55), more images can be shot because data sie per image will be smaller than
with 4:3 images. However, since
imges have a setting of 1920 x 1080 pixels,
their data size will be larger than 4es.
Approximate Valuefor Paper Size (for 4:3 Aspect Ratios)
A2 (16.5 x 23.4 in.)
z
For sending images as e-mail
attachments.
A3 – A5 (11.7 x
16.5 – 5.8 x 8.3 in.)
5 x 7 in.
Postcard size
3.5 x 5 in.
57
Correcting the Green Tint from Mercury
Lamps
When shooting scenes lit by mercury lamps, such as night scenes, the
subject and background in the recorded image may have a green tint. You
can automatically correct the green tint when shooting (Multi-area White
Balance).
Display the menu.
z Press the n button.
Choose [Hg Lamp Corr.].
z Move the zoom lever to choose the 4 tab.
z Press the op buttons or turn the 5 dial
to choose [Hg Lamp Corr.].
Choose a setng.
z Press tqr butons to choose [On].
z the n button to complete the
sand restore the shooting screen.
X Once set,
will appear on the screen.
z To turn this function off, follow the Steps
above to choose [Off].
• After shooting scenes lit by mercury lamps, you should set [Hg Lamp
Corr.] to [Off]. If left set to [On], naturally occurring green colors (not from
the effects of a mercury lamp) may be accidentally corrected.
• Movies cannot be corrected.
• Since you may not achieve the expected results depending on the
shooting conditions, try taking some test shots first.
58
Take shots of moving subjects (Sports)
Lets you shoot continuous images of a moving subject while focusing
automatically.
At maximum wide angle, move approximately 1 m (3.3 ft.) or more away from
your subject. At maximum telephoto, move approximately 10 m (33 ft.) or
more away from your subject and shoot.
Enter
mode.
z Set the mode dial to
.
Focus.
z The focus and brightness will be
maintained where the blue AF frame
appears while you press the shutter button
halfway.
Shoot.
z g s you hold the shutter button
dhe camera will shoot successive
images.
In
mode, images may appear coarse because the ISO speed (p. 81) is
increased to match the shooting conditions.
60
Shooting in Special Scenes
The camera will select the necessary settings for the conditions in which you
wish to shoot when you choose the matching mode.
Enter K mode.
z Set the mode dial to K.
Choose a Shooting mode.
z After pressing the m button, press the
op buttons to choose
.
z Press the qr buttons or turn the 5 dial to
choose a Shooting mode, then press the
m button.
Shoot.
I Take portraits (Portrait)
z Produces a soft effect when
photographing people.
JTake landscapes (Landscape)
z Lets you shoot majestic landscapes with a
real sense of depth.
61
Shooting in Special Scenes
Take nightscapes without using a
z Lets you take beautiful snapshots of city
nightscenes by combining several
continuous shots to reduce camera shake
and noise.
z When using a tripod, you should shoot in
A mode (p. 25).
Take shots in low light conditions
(Low Light)
z Lets you take shots in dark places with
reduced camera shake and subject blur.
wAt the beach Beach)
z Lets yoke shts of brightly lit people on
baches where the reflected
st is strong.
OTake shots of foliage (Foliage)
z Lets you shoot trees and leaves, such as
new growth, autumn leaves or blossoms,
in vivid colors.
P Against snow (Snow)
z Lets you take bright, natural-colored shots
of people against snowy backgrounds.
62
Shooting in Special Scenes
t Take shots of fireworks
(Fireworks)
z Lets you take shots of fireworks in vivid
colors.
• In
mode, hold the camera firmly while shooting as multiple images are
captured in succession.
• In t mode, attach the camera to a tripod to prevent the camera from
moving and blurring the image. Additionally, you should set [IS Mode] to
[Off] when shooting with a tripod (p. 168).
• In
mode, images may appear coarse because the ISO speed (p. 81)
is increased to match the shooting conditions.
• If camera shake is too strong while shooting in
mode, the camera
may not be able to combine images or ou may not obtain the expected
result depending on shooting conditio
• In
mode, the recording pixing wl be fixed at
(1984 x 1488
pixels).
63
Adding Effects and Shooting
(Creative Filters)
You can add various effects to images when shooting.
Enter
mode.
z Set the mode dial to
.
Choose a Shooting mode.
z After pressing the m button, press the
op buttons to choose
.
z Press the op buttons or turn the 5 dial
to choose a Shooting mode, then press the
m button.
Shoot.
Since you may not achive the expected results with images shot in
,
,
,
and
modes, try taking some test shots first.
Shoot images with vivid colors
(Super Vivid)
z Lets you take shots with vivid, intense
colors.
Take posterized shots
(Poster Effect)
z Lets you take shots that look like an old
poster or illustration.
64
Adding Effects and Shooting (Creative Filters)
Shooting with the Effects of a Fish-Eye Lens
(Fish-eye Effect)
Lets you shoot with the distorting effect of a fish-eye lens.
Choose
.
z Follow Steps 1 – 2 on p. 64 to choose
.
Choose an effect level.
z If you press the l button, [Effect Level]
will appear on the screen.
z Press the qr buttons or turn the 5 dial to
choose an effect level, then press the
l button.
X You can check the effect on the screen.
Shoot.
Taking Shots That k Like a Miniature Model
(Miniature Effect)
Blurs chosen portions in the toand bottom of an image to produce the effect
of a miniature model.
Choose
.
z Follow Steps 1 – 2 on p. 64 to choose
X A white frame (the area that will not be
blurred) appears on the screen.
.
Choose the area to keep in focus.
z Press the l button.
z Move the zoom lever to change the frame
size, and press the op buttons to change
the frame position, then press the l
button.
Shoot.
65
Adding Effects and Shooting (Creative Filters)
• If you press the m button in Step 2, the horizontal/vertical orientation of
the frame will switch, and you can press the qr buttons to change the
frame position when it is displayed vertically.
• Holding the camera vertically will change the orientation of the frame.
• Be sure to set
(playback speed) before shooting a Miniature Effect
movie (p. 110).
Shooting with the Effects of a Toy Camera
(Toy Camera Effect)
This effect darkens and blurs the corners of the image, and changes the
overall color so that it looks like an image shot with a toy camera.
Choose
.
z Follow Steps 1 – 2 on p. 64 to choose
.
Choose a colr tone.
z Press l button.
X r Tne] will appear on the screen.
z he qr buttons or turn the 5 dial to
choe a color tone, then press the l
button.
X You can check the color tone on the
screen.
Shoot.
Standard
Warm
Cool
Images will look like they were shot with a toy camera.
Gives images a warmer tone than [Standard].
Gives images a cooler tone than [Standard].
66
Adding Effects and Shooting (Creative Filters)
Shooting in Monochrome
You can shoot images in black and white, sepia or blue and white.
Choose
.
z Follow Steps 1 – 2 on p. 64 to choose
.
Choose a color tone.
z Press the l button.
X [Color Tone] will appear on the screen.
z Press the qr buttons or turn the 5 dial to
choose a color tone, then press the l
button.
X You can check the color tone on the
screen.
Shoot.
B/W
Lets you shoot black hitmages.
Sepia
Blue
Lets you shoot sepia mages.
Lets you shooblue and white images.
Shooting with Color Accent
You can choose to retain a single color and change the rest to black and white
in a composition.
Choose T.
z Follow Steps 1 – 2 on p. 64 to choose T.
Press the l button.
X The unchanged image and the Color
Accent image will alternately display.
X The color for default settings is green.
67
Adding Effects and Shooting (Creative Filters)
Specify the color.
z Position the center frame so it is filled with
the color you want and press the q button.
X The specified color will be recorded.
Specify the range of colors.
z Press the op buttons or turn the 5 dial
to change the range of colors to be
retained.
Recorded color
z Choose a negative value to limit the range
of colors. Choose a positive value to
extend the range of colors to similar colors.
z Press the l button to complete the
setting and restore the shooting screen.
• Using the flash may cause unexpected rests in this mode.
• Depending on shooting conditions, the imamay become coarse, or the
colors may not come out as expec
Shooting with Color Sp
You can swap one color in aimage for another when recording it. You can
only swap one color.
Choose Y.
z Follow Steps 1 – 2 on p. 64 to choose Y.
Press the l button.
X The unchanged image and the Color Swap
image will alternately display.
X The default setting is to change green to
gray.
68
Adding Effects and Shooting (Creative Filters)
Specify the color to be swapped.
z Position the center frame so it is filled with
the color you want and press the q button.
X The specified color will be recorded.
Specify the target color.
z Position the center frame so it is filled with
the color you want and press the r button.
X The specified color will be recorded.
Specify the range of colors to be
swapped.
z Press the op buttons or turn the 5 dial
to adjust hrange of colors to be
swd.
hoe a negative value to limit the range
olors. Choose a positive value to
end the range of colors to similar colors.
z Press the l button to complete the
setting and restore the shooting screen.
• Using the flash may cause unexpected results in this mode.
• Depending on shooting conditions, the image may become coarse, or the
colors may not come out as expected.
69
Making Short Movies Automatically
(Movie Digest)
You can make a short movie of a day just by taking still images.
Each time you take a picture, the scene just before taking your shot will be
recorded as a movie. All the movies recorded that day will be saved as a
single file.
Choose
.
z Follow Steps 1 – 2 on p. 61 to choose
.
Shoot.
z Press the shutter button fully to shoot a still
image.
X A movie of approx. 2 – 4 sec. will be
recorded just before the image is taken.
What if a movie is not recorded?
If you take a picture just after turning on thmera, selecting
otherwise operating the camera, a movie mot be recorded.
mode or
Viewing movies made wivie Digest mode
You can select movies made i
mode by date for viewing (p. 121).
• Since you are also shooting movies when you shoot still images, the
• The image quality will be fixed at
• In the following cases, movies will be saved as separate files even if they
were made on the same day with mode.
mode.
- If the clip file size reaches 4 GB or the recording time reaches approximately
1 hour
- If the movie is protected (p. 128)
- If the Time Zone setting is changed (p. 163)
- If a new folder is created (p. 162)
• If you operate the camera while shooting a movie, the sounds made will
be recorded in the movie.
• The camera will not play sounds, such as when pressing the shutter
button halfway, using the controls or the self-timer (p. 158).
70
Detecting a Face and Shooting
(Smart Shutter)
Detecting a Smile and Shooting
The camera will shoot, even without pressing the shutter button, when it
detects a smile.
Choose
.
z Follow Steps 1 – 2 on p. 61 to choose
,
then press the l button.
z Press the qr buttons or turn the 5 dial to
choose
, then press the l button.
X The camera will enter shooting stand-by,
and [Smile Detection on] will appear on the
screen.
Point the camera at a person.
z Eame the camera detects a smile it will
shofter the lamp lights.
ss the p button to pause smile
ection. Press the p button again to
resume smile detection.
What if a smile is not detected?
Smiles are easier to detect if the subject faces the camera, and opens their mouth
enough to show some teeth when smiling.
Changing the number of shots
After choosing
in Step 1, press the op buttons.
• You should switch to another mode when you finish shooting, or the
camera will continue taking shots each time the camera detects a smile.
• You can also shoot by pressing the shutter button.
71
Detecting a Face and Shooting (Smart Shutter)
Using the Wink Self-Timer
Point the camera at a person and press the shutter button fully. The camera
will shoot approximately 2 seconds after it detects a wink.
Choose
.
z Follow Steps 1 – 2 on p. 61 to choose
,
then press the l button.
z Press the qr buttons or turn the 5 dial to
choose
, then press the l button.
Compose the shot and press the
shutter button halfway.
z Confirm that a green frame appears
around the face of the person who will
wink.
Press tshuter button fully.
X amra will enter shooting stand-by,
aink to take picture] will appear on
the screen.
X The lamp will blink and the self-timer
sound will play.
Face the camera and wink.
X The shutter will release approximately 2
seconds after a wink is detected from the
person inside the frame.
z To cancel shooting with the self-timer after
the countdown has started, press the
n button.
What if a wink is not detected?
• Wink a bit slowly.
• A wink may not be detected if eyes are covered by hair or a hat, or when wearing
glasses.
72
Detecting a Face and Shooting (Smart Shutter)
Changing the number of shots
After choosing
in Step 1, press the op buttons.
• Shutting both eyes will also be detected as a wink.
• If a wink is not detected, the shutter will release approximately 15
seconds later.
• If there are no people in the shot when the shutter button is pressed fully,
the camera will shoot after a person enters the shot and winks.
Using the Face Self-Timer
The shutter will release approximately 2 seconds after the camera detects a
new face (p. 87). You can use this when the photographer wants to be in the
image, such as a group photo.
Choose
z FollStep1 – 2 on p. 61 to choose
,
thess the l button.
ess the qr buttons or turn the 5 dial to
ose
, then press the l button.
Compose the shot and press the
shutter button halfway.
z Make sure a green frame appears on the
face focused on and white frames appear
on other faces.
Press the shutter button fully.
X The camera will enter shooting stand-by,
and [Look straight at camera to start count
down] will appear on the screen.
X The lamp will blink and the self-timer
sound will play.
73
High-Speed Continuous Shooting (High-speed Burst HQ)
Join the subjects and look at the
camera.
X When the camera detects a new face, the
lamp and self-timer sound will speed up
(the lamp remains lit when the flash will
fire), and approximately 2 seconds later
the shutter will release.
z To cancel shooting with the timer after
countdown has started, press the n
button.
Changing the number of shots
After choosing
in Step 1, press the op buttons.
Even if your face is not detected after joining the subjects, the shutter will
release approximately 15 seconds later.
High-Speed ContinuoShooting
(High-speed Burst )
While the shutter button is pessed down, you can shoot up to 8 continuous
shots at a maximum speed of pprx. 10.3 images per second. HQ stands for
"High Quality".
Choose
.
z Follow Steps 1 – 2 on p. 61 to choose
,
then press the l button.
Shoot.
X As long as you hold the shutter button
down, the camera will shoot successive
images.
z Release your finger from the shutter button
to finish shooting, or shooting will end
automatically when the maximum number
of images have been shot. [Busy.] will
appear on the screen, and the images will
display in the order they were taken.
74
High-Speed Continuous Shooting (High-speed Burst HQ)
• The focus, brightness and white balance will be set with the first shot.
• Nothing will appear on the screen while shooting.
• After continuous shooting ends, a certain amount of time may be needed
before you can take the next shot.
• Depending on the shooting conditions, camera settings and the zoom
position, the shooting speed may slow down.
Images Displayed During Playback
part of a group,
If you erase a grouped image (p. 132), all the images in the group will also
• You can play back images individually (p. 125), and cancel grouping
(p. 126).
group.
• If you play back grouped s sing Filtered Playback (p. 121) or
Smart Shuffle (p. 27), gris temporarily canceled and images are
played back indivually.
• Grouped images canobe tagged as favorites (p. 134), edited (pp. 138
– 143), categorized (p. 135), printed (p. 146) or added to the print list
(p. 154). Play back grouped images individually (p. 125), or cancel
grouping (p. 126) before trying the above.
75
Shooting Stitch Assist Images
Large subjects can be split into several shots that can later be merged
together using the included software on a computer to create a panoramic
image.
Choose x or v.
z Follow Steps 1 – 2 on p. 61 to choose x
or v.
Take the first shot.
X The exposure and white balance will be set
with the first shot.
Take subsequent shots.
z Overlap part ohe first shot when taking
the seshot
z direpancies in the overlapping
s will be corrected when the images
are erged.
z Up to 26 shots can be recorded with the
same procedures.
Finish shooting.
z Press the m button.
Merge the images on a computer.
z For details on how to merge the images,
refer to the Software Guide.
• This function is not available when a TV is used as a display (p. 175).
• To use AF lock, register % to the
button (p. 170).
76
Choosing Settings Yourself
In this chapter you will learn how to use the various functions in G
mode to progressively advance your shooting skills.
•
•
•
This chapter assumes that you have set the mode dial to G mode.
G stands for Program AE.
Before attempting to shoot using a function explained in this chapter in
modes other than G mode, check if the function is available in those modes
(pp. 196 – 203).
77
Shooting in Program AE
You can choose the settings for various functions to suit your preferences.
AE stands for Auto Exposure.
The focusing range is approximately 5 cm (2 in.) – infinity at maximum wide
angle (j), and approximately 1.4 m (4.6 ft.) – infinity at maximum telephoto
(i).
Enter G mode.
z Set the mode dial to G.
Adjust the settings according to
your purposes (pp. 78 – 100).
Shoot.
What if the shutter speed and aperture value appear in orange?
If a correct exposure cannot be obtained when presing the shutter button
halfway, the shutter speed and aperture value appein orange. Try the following
settings to obtain the correct exposure.
• Turn on the flash (p. 79)
• Choose a higher ISO speed (p. 81
Adjusting the Brightness
(Exposure Compensation)
You can adjust the standard exposure set by the camera in 1/3-stop
increments in the range of –2 to +2.
Enter Exposure Compensation
mode.
z Press the o button.
Adjust the brightness.
z While watching the screen, turn the 5 dial
to adjust the brightness, then press the o
button.
X The exposure compensation amount will
appear on the screen.
78
Turning the Flash On
You can make the flash fire every time you shoot. The effective flash range is
approximately 50 cm – 7.0 m (1.6 – 23 ft.) at maximum wide angle (j), and
approximately 1.4 – 3.0 m (4.6 – 9.8 ft.) at maximum telephoto (i).
Raise the flash.
Choose h.
z After pressing the h button, press the qr
buttons or turn the 5 dial to choose h,
then press the m button.
X Once set, h will appear on the screen.
What if the setting screen does not appear even when you
press the h button?
The flash is lowered. Raise the flash manually.
Correcting the Brightnes and Shooting
(i-Contrast)
The camera can detect areas icee, such as faces or backgrounds,
that are too bright or darand autically adjust them to the optimum
brightness when shootingAlsowhen the overall image is lacking in contrast,
the camera will automatically correct the image for a sharper impression
when shooting.
Choose [i-Contrast].
z Press the n button to choose [i-
Contrast] in the 4 tab, then press the qr
buttons to choose [Auto].
X Once set, @ will appear on the screen.
• Under some conditions, the image may appear coarse or may not be
corrected properly.
• You can correct recorded images (p. 142).
79
Adjusting the White Balance
The white balance (WB) function sets the optimal white balance for natural
looking colors to match the shooting conditions.
Choose the white balance function.
z After pressing the m button, press the
op buttons to choose
.
Choose an option.
z
Press the qr buttons or turn the
choose an option, then press the
5
m
dial to
button.
X The setting will appear on the screen.
Auto
Automatically sets the optimal white balance for the shooting conditions.
For shooting outdoors, in fine weather conditions.
Day Light
Cloudy
For shooting in cloudy, shady or twilight conditions.
For shooting under tungsten and blb-type (3-wavelength)
fluorescent lighting.
Tungsten
For shooting under warmfluorscent, cool-white fluorescent
and warm-white-typ(3-wength) fluorescent lighting.
Fluorescent
Fluorescent H
For shooting undeht fuorescent and daylight-type (3-
wavelengthfluoresghting.
Flash
For shootinwith he flash.
h
Custom
For manually setting a custom white balance.
Custom White Balance
You can adjust the white balance to match the light source at the shooting
location. Make sure that you set the white balance under the light source of
the actual scene you will shoot.
z In Step 2 above, choose
.
z Make sure the entire screen is filled with a
plain, white colored subject, then press the
l button.
X The tint on the screen will change when
white balance data is set.
If you change camera settings after recording white balance data, the tone
may not turn out properly.
80
Changing the ISO Speed
Choose the ISO speed.
z After pressing the r button, press the qr
buttons or turn the 5 dial to choose an
option, then press the
X The option you set will appear on the
button.
m
screen.
Automatically adjusts the ISO speed to the Shooting mode and shooting
conditions.
Low For shooting outdoors, in fine weather conditions.
For shooting in cloudy or twilight conditions.
For shooting nightscapes or in dark interiors.
High
Changing the ISO speed
• Lowering the ISO speed results in sharper images, but there may be an
increased chance of image blurring in certain hooting conditions.
• Raising the ISO speed results in a fastutter speed, reducing image blurring
and letting the flash reach greater dists to the subject. The images,
however, will appear coarse.
When the camera iset to
u can press the shutter button halfway to
display the automatally et ISO speed.
Changing the Tone of an Image
(My Colors)
You can change the tone of an image, for example to sepia or black and
white, when shooting.
Choose My Colors.
z After pressing the m button, press the
op buttons to choose
.
Choose an option.
5
m
z
Press the qr buttons or turn the
choose an option, then press the
dial to
button.
X The setting will appear on the screen.
81
Changing the Tone of an Image (My Colors)
My Colors Off
—
Emphasizes the contrast and color saturation for a vivid
impression.
Vivid
Neutral
Sepia
B/W
Tones down the contrast and color saturation for neutral hues.
Changes the image to sepia tones.
Changes the image to black and white.
Combines the effects of Vivid Red, Vivid Green and Vivid Blue
to produce intense natural appearing colors like those
obtained with positive film.
Positive Film
Lighter Skin Tone Makes skin tones lighter.
Darker Skin Tone Makes skin tones darker.
Emphasizes blue tints. Makes the sky, ocean and other blue
subjects more vivid.
Vivid Blue
Emphasizes green tints. Makes mountains, foliage and other
green subjects more vivid.
Vivid Green
Vivid Red
Emphasizes red tints. Maks d subjects more vivid.
You can adjust contharpess, and color saturation etc.
to your prefer.
Custom Color
• The white balance cannot b
• In and , colorother than people’s skin color may change. You
may not obtain the expcteresults with some skin colors.
and
(p. 80).
Custom Color
The contrast, sharpness, color saturation, red, green, blue, and skin tones in
an image can be chosen and set at 5 different levels.
z Follow Step 2 on p. 81 to choose
, then
press the l button.
z Press the op buttons to choose an
option, then press the qr buttons or turn
the 5 dial to choose a value.
z The more to the right, the stronger/darker
(skin tone) the effect gets, the more to the
left, the weaker/lighter (skin tone) the
effect gets.
z Press the l button to complete the
setting.
82
Continuous Shooting
As long as you hold the shutter button down, the camera will shoot
continuously.
Choose a Drive mode.
z After pressing the m button, press the
op buttons to choose
.
Choose an option.
z Press the qr buttons or turn the 5 dial to
choose an option, then press the m
button.
X The option you set will appear on the
screen.
Shoot.
X As long as ou hold the shutter button
down, the mera will shoot successive
im
Maximum
Speed
Mode
Description
(Appox.
imagesec.)
The camera shoots continuously with the focus and
exposure set when the shutter button is pressed
W Continuous
2.4
0.8
0.9
Continuous
Shooting AF
The [AF Frame] is set to [Center].
The camera shoots continuously with the focus fixed
to the position set in manual focus. In t mode, the
focus is locked on the first shot.
Continuous
Shooting LV*
* When in t mode (p. 63), AF lock (p. 91) or manual focus modes (p. 93),
will change to
.
• Cannot be used with the self-timer (p. 53).
• Depending on the shooting conditions, camera settings and the zoom
position, the camera may stop shooting momentarily, or the shooting
speed may slow down.
• As the number of images increases, the shooting speed may slow down.
• If the flash fires, the shooting speed may slow down.
83
Shooting Close-ups (Macro)
If you set the camera to e, it focuses on close subjects only. The focusing
range is approximately 0 – 50 cm (0 – 1.6 ft.) from the end of the lens at
maximum wide angle (j).
Choose e.
z After pressing the q button, press the qr
buttons or turn the 5 dial to choose e,
then press the m button.
X Once set, e will appear on the screen.
• The edges of the image may darken if the flash fires.
• Be careful to avoid damaging the lens.
How can I take better close-ups?
Try attaching the camera to a tripod and shooting n to prevent the camera from
moving and blurring the image (p. 54).
e will turn gray in the area thplain the yellow bar underneath the
zoom bar, and the camera wilcus
84
Using the Digital Tele-Converter
The focal length of the lens can be increased by 1.5x or 2.0x. This enables a
faster shutter speed and less chance of camera shake than the zoom
(including digital zoom) used by itself at the same zoom factor.
Choose [Digital Zoom].
z Press the n button to choose [Digital
Zoom] in the 4 tab, then press the qr
X The view will be enlarged and the zoom
factor will appear on the screen.
• The respective focal lengths when using [1.5x] and [2.0x] are 36.0 –
1260 mm and 48.0 – 1680 mm (35mm film equivalent).
• A recording pixel setting (p. 56) of
or
will cause images to appear
coarse (the zoom factor will appear in blue).
• The digital tele-converter cannot be used together with the digital zoom
(p. 50).
• The digital tele-converter can bed in he following aspect ratio and
recording pixel setting combinat:
Aspect ratios of
or
reording pixel setting of
An aspect ratio of
in er recording pixel settings
• The shutter speeds may be the same when at maximum telephoto i,
and when zoomed iothe subject using Step 2 on p. 50.
85
Changing the AF Frame Mode
You can change the AF (Auto Focus) frame mode to match the scene you
want to shoot.
Choose [AF Frame].
z Press the n button to choose [AF
Frame] in the 4 tab, then press the qr
buttons to choose an option.
FlexiZone/Center
A single AF frame will be used. This is effective for focusing on a specific
point. In [FlexiZone], you can change the position and size of the AF frame
(p. 88).
If the camera cannot focus when you press thshutter button halfway, the
AF frame will turn yellow and
wilear.
Changing the Composition h te Focus Lock
While you keep the shutter button d halfway, the focus and exposure
are locked. You can now recompose and shoot. This is called Focus Lock.
Focus.
z Center the subject you want in focus, and
press the shutter button halfway.
z Confirm that the AF frame on the subject is
green.
Recompose.
z Keep the shutter button pressed halfway
and move the camera to recompose the
scene.
Shoot.
z Press the shutter button fully.
86
Changing the AF Frame Mode
Face Detect
Detects people’s faces and sets the focus, exposure (evaluative metering
•
•
only) and white balance ( only).
When the camera is pointed at subjects, a white frame appears on the face
the camera judges to be the main subject, and gray frames (max. 2) will
appear on other faces.
•
•
A frame will follow a moving subject within a certain range.
When the shutter button is pressed halfway, up to 9 green frames will
appear on faces that the camera focuses on.
• If a face is not detected, or only gray frames (no white frame) appear, an
AF frame will appear in the center of the screen when you press the
shutter button halfway.
• If a face is not detected when Servo AF (p. 91) is set to [On], the AF frame
will appear in the center of the screen when you press the shutter button
halfway.
• Examples of faces that cannot be deted:
- Subjects that are far away or exly cloe
- Subjects that are dark or
- Faces turned to the side angle, or faces with a portion hidden
• The camera may mistakeentify non-human subjects as a face.
• If the camera cannot focus when you press the shutter button halfway,
the AF frame will not appear.
Tracking AF
You can choose the subject you want to focus on and shoot (p. 89).
87
Changing the AF Frame Position and Size
When the AF frame mode is set to [FlexiZone] (p. 86), you can change the
position and size of the AF frame.
Press the
button.
X The AF frame will turn orange.
Move the AF frame.
z Turn the 5 dial to move the AF frame.
z Press the opqr buttons to make fine
adjustments.
z If you keep the
button pressed, the AF
frame will return to the original position
(center).
Change the AF frame size.
z Press the l button.
X The AF frame will become small.
z Press the l button again to restore the
AF frame to normal size.
Complete the settings.
z Press the
button.
• The spot AE point frame can be linked with the AF frame (p. 95).
• The AF frame will be set to [Normal] when using the digital zoom (p. 50)
or digital tele-converter (p. 85).
88
Choosing the Subject to Focus On
(Tracking AF)
You can choose the subject you want to focus on and shoot.
Choose [Tracking AF].
z Press the n button to choose [AF
Frame] in the 4 tab, then press the qr
buttons to choose [Tracking AF].
X
will appear in the center of the screen.
Choose the subject to focus on.
z Point the camera so that
is on the
subject you want to focus on and press the
button.
X The mera ill beep and
will appear
en a subject is detected. The camera
continue to track the subject within a
certain range even if the subject moves.
X If the camera does not detect the subject,
will appear on the screen.
z To cancel tracking, press the
button
again.
Shoot.
z Press the shutter button halfway.
will
change into a blue
which will follow the
subject while the camera continues to
adjust the focus and exposure (Servo AF)
(p. 91).
z Press the shutter button fully to shoot.
X Even after shooting completes,
will
appear, and the camera will continue to
track the subject.
89
Magnifying the Focal Point
• The camera will detect a subject even if you press the shutter button half
way without pressing the
button. When shooting completes,
will
appear in the center of the screen.
• [Servo AF] (p. 91) is fixed to [On].
• The camera may not be able to track the subject if the subject is too small,
moves too quickly or if the contrast between the subject and the
background is too low.
• Not available in e.
Magnifying the Focal Point
If you press the shutter button halfway, the AF frame will magnify and you can
check the focus.
Choose [AF-Point Zoom].
z Press the n button to choose [AF-
Point Z] in he 4 tab, then press the
qr buts to choose [On].
Check the focus.
z Press the shutter button halfway.
X In [Face Detect] (p. 87), the face detected
as the main subject will appear magnified.
X In [FlexiZone] or [Center] (p. 86), the
contents of the AF frame will appear
magnified.
What if the display does not magnify?
The display will not appear magnified in [Face Detect] if a face cannot be detected
or is too big in relation to the screen. In [FlexiZone] or [Center], it will not appear
magnified if the camera cannot focus.
The magnified display will not appear when using the digital zoom (p. 50),
digital tele-converter (p. 85), Tracking AF (p. 89), Servo AF (p. 91) or when
using a TV as a display (p. 175).
90
Shooting with the AF Lock
The focus can be locked. After locking the focus, the focal distance will not
change even when you release your finger from the shutter button.
Lock the focus.
z Keep the shutter button pressed halfway
and press the q button.
X The focus locks, and
and the MF
indicator appear on the screen.
z After you release your finger from the
shutter button, press the q button again,
then press the qr buttons or turn the 5
dial to choose
. The focus will unlock.
Compose the scene and shoot.
Shooting with Servo AF
While the shutter button is preshalay, the focus and exposure will
continue to adjust, allowing you e pictures of moving subjects without
missing a shot.
Choose [Servo AF].
z Press the n button to choose [Servo
AF] in the 4 tab, then press the qr
buttons to choose [On].
Focus.
z The focus and exposure will be maintained
where the blue AF frame appears while
you press the shutter button halfway.
• The camera may not be able to focus in some conditions.
• In low light conditions, AF frames may not turn blue even after pressing
the shutter button halfway. In this case, you can set the focus and
exposure with the AF frame setting.
91
Focus Bracketing (Focus-BKT Mode)
value appear in orange. Release your finger from the shutter button, then
press it again halfway.
• You cannot shoot with the AF lock in this mode.
• The [AF-Point Zoom] option in the 4 tab is not available in Servo AF
mode.
• Not available when using the self-timer (p. 53).
Focus Bracketing (Focus-BKT Mode)
The camera automatically takes 3 continuous shots in the following order:
one at the position set in manual focus, and one each with focus positions
preset farther and nearer. The focus adjustment can be set in 3 levels.
Choose
.
z After pressing he m button, press the
, then press the
op bs to hoose
qbuts or turn the 5 dial to choose
Set the focus.
z Press the l button.
set the focus.
• Focus Bracketing is only available in ! (p. 26).
• Continuous shooting (p. 83) cannot be used in this mode.
• If you follow Step 1 on p. 93 to choose
and immediately press the
l button, the focus adjustment screen will appear.
• Even if you set the number of shots in $ (p. 54), only 3 shots will be
taken.
92
Shooting in Manual Focus Mode
You can use manual focus when auto focus is not possible. If you press the
shutter button halfway after roughly focusing manually, you can fine tune the
focus.
Choose
.
z After pressing the q button, press the qr
buttons or turn the 5 dial to choose
then press the m button.
,
X
and the MF indicator appear.
Focusing roughly.
z The side bar shows your focal point and a
distance display for the MF indicator. While
looking at the magnified area, turn the 5
dial to find n approximate focus.
Fine ing the focus.
ou press the shutter button halfway, you
fine tune the focus (Safety MF).
z You can also fine tune the focus by
MF Indicator
pressing the
button.
• You cannot change the AF frame mode or size while focusing manually
(p. 86). If you want to change the AF frame mode or size, cancel manual
focus mode first.
• In order to focus accurately, try attaching the camera to a tripod.
• When using the digital zoom (p. 50), digital tele-converter (p. 85), or when
using a TV as a display (p. 175), you will be able to focus but the
magnified area will not display.
• If you press the n button to display the 4 tab and set [MF-Point
Zoom] to [Off], the magnified display will not be available.
• If you press the n button to display the 4 tab and set [Safety MF]
to [Off], you will not be able to fine tune the focus even if you press the
shutter button halfway.
93
Choosing the Person to Focus On
(Face Select)
You can choose a specific person’s face to focus on and then shoot.
Set the AF frame to [Face Detect]
(p. 87).
Enter Face Select mode.
z Point the camera toward the face of the
subject and press the
X After [Face Select : On] appears, a face
frame will appear around the face
button.
detected as the main subject.
z Even if the subject moves, the face frame
will follow the subject within a certain
range.
z If a face is not etected,
will not
appear.
Chse e face to focus on.
z Iress the
button, the face frame
will move to another face detected by
he camera.
z When the frame has made a full circuit of
all detected faces, [Face Select : Off] will
appear, and the AF frame mode screen will
reappear.
Shoot.
z Press the shutter button halfway. When
the camera focuses,
will change into
.
z Press the shutter button fully to shoot.
94
Changing the Metering Method
You can change the metering method (brightness measuring function) to
match the shooting conditions.
Choose the metering method.
z After pressing the m button, press the
op buttons to choose
.
Choose an option.
z Press the qr buttons or turn the 5 dial to
choose an option, then press the m
button.
X The setting will appear on the screen.
For standard shooting conditions, including back lit shots.
Automatically adjusts the exposure to match the shooting
conditions.
Evaluative
Center
Averages the light metered frothe entire frame, but gives greater
Weighted Avg. weight to the center.
Only meters within th
Spot
(SpoAE Point frame). The Spot AE
Point frame clinkd to the AF frame.
Linking the Spt AE Point Frame to the AF
Frame
Choose
.
z Follow Step 2 above to choose
.
Choose [Spot AE Point].
z Press the n button to choose [Spot
AE Point] in the 4 tab, then press the qr
buttons to choose [AF Point].
X The Spot AE Point frame will be linked to
the AF frame that was moved.
Cannot be used when [AF Frame] is set to [Face Detect] (p. 87) or
[Tracking AF].
95
Shooting with the AE Lock
You can lock the exposure and shoot, or set the focus and exposure
separately to shoot. AE stands for “Auto Exposure”.
Lock the exposure.
z Point the camera toward the subject and
press the o button while pressing the
shutter button halfway.
X When
appears, the exposure will be
locked.
z If you release your finger from the shutter
button and press the o button again,
will disappear and AE will unlock.
Compose the scene and shoot.
z When you shoot one image,
will
disappear and AE will unlock.
Program Shift
If you lock the exposure and turn the al, ou can change the shutter speed
and aperture value combination.
Shooting with the FE Lock
Just as with the AE lock, you can lock the exposure for shooting with the flash.
FE stands for “Flash Exposure”.
Raise the flash and choose
(p. 79).
h
Lock the flash exposure.
z Point the camera toward the subject and
press the o button while pressing the
shutter button halfway.
X The flash will fire and when
appears,
the flash output will be retained.
96
Auto Exposure Bracketing (AEB Mode)
z If you release your finger from the shutter
button and press the o button again,
will disappear and FE will unlock.
Compose the scene and shoot.
z When you shoot one image,
will
disappear and FE will unlock.
Auto Exposure Bracketing (AEB Mode)
The camera takes 3 continuous shots while automatically adjusting the
exposure to standard exposure, underexposure and overexposure, in that
order.
Choose
.
z After pressng the m button, press the
, then press the
op buttoto choose
qr ons r turn the 5 dial to choose
.
Set the exposure compensation
amount.
z Press the l button.
z Press the qr buttons or turn the 5 dial to
adjust the setting.
z From the exposure set by the camera, you
If exposure compensation (p. 78) is
already being used, settings are made with
the compensated value as the base.
• AEB is only available in ! (p. 26).
• Continuous shooting (p. 83) cannot be used in this mode.
• If you press the l button while in the exposure compensation screen
(p. 78), the compensation amount setting screen will appear.
• Even if you set the number of shots in $ (p. 54), only 3 shots will be
taken.
97
Adjusting the Flash Exposure
Compensation
Just as with exposure compensation (p. 78), you can adjust the exposure
from –2 to +2 stops in 1/3-stop increments when using the flash.
Choose X.
z After pressing the m button, press the
op buttons to choose X.
Choose the amount of flash
exposure compensation.
z Press the qr buttons or turn the 5 dial to
choose the amount of flash exposure
compensation, then press the m button.
X Once set, X will appear on the screen.
Safety FE
flash fires to avoid overexposing and winut the highlights in the scene.
However, if you press the n buispay the 4 tab and set [Safety FE]
in [Flash Control] to [Off], the hutter and aperture value will not
automatically adjust.
• You can also set the flash exposure compensation by pressing the
n button to choose [Flash Control] (p. 99) in the 4 tab, then choose
[Flash Exp. Comp] and press the qr buttons to choose a setting.
• If you hold down the h button for more than 1 second, the setting screen
will appear. If you press the h button then immediately press the n
button when the flash is raised, the setting screen will appear.
Shooting with Slow Synchro
You can make the main subject, such as people, appear bright by having the
camera provide the appropriate illumination with the flash. At the same time,
you can use a slow shutter speed to brighten the background that the light
from the flash cannot reach.
Raise the flash.
98
Red-Eye Correction
Choose Z.
z After pressing the h button, press the qr
buttons or turn the 5 dial to choose Z,
then press the m button.
X Once set, Z will appear on the screen.
Shoot.
z Even if the flash fires, ensure that the main
subject does not move until the shutter
sound ends.
Attach the camera to a tripod to prevent the camera from moving and
blurring the image. Additionally, you should set [IS Mode] to [Off] when
shooting with a tripod (p. 168).
What if the setting screen does not appear even when you
press the h button?
The flash is lowered. Raise the flash mly.
Red-Eye Correct
You can automatically corect ed-eye that occurs in images taken with the
flash.
Choose [Flash Control].
z Press the n button to choose [Flash
Control] in the 4 tab, then press the m
button.
Choose the setting.
z Press the op buttons or turn the 5 dial
to choose [Red-Eye Corr.], then press the
qr buttons to choose [On].
X Once set, R will appear on the screen.
99
Checking for Shut Eyes
Red-eye correction may be applied to areas other than red eyes. For
example, when red make-up has been used around eyes.
• You can also correct recorded images (p. 143).
• If you hold down the h button for more than 1 second, the screen in Step
2 will appear.
• If you press the h button then immediately press the n button when
the flash is raised, the screen in Step 2 will appear.
Checking for Shut Eyes
When the camera detects the possibility that people have their eyes shut,
appears on the screen.
Choose [Blink Detection].
z Press the n button to choose [Blink
Detection] in t4 tab, then press the
qr buto coose [On].
Sh
X Wha person with shut eyes is detected,
a frame and
appear on the screen.
• This function is only available for the last image shot when you have set
the camera to 2 or more shots in or $ mode.
• This function is only available for the last image shot in
and
modes.
• Not available in W,
or
mode.
100
Setting the Shutter Speed
You can set the shutter to the speed at which you want to shoot. The camera
will set the appropriate aperture value for the shutter speed you set.
Mstands for “Time value”.
Set the mode dial to M.
Adjust the setting.
z Turn the 5dial to set the shutter speed.
Shoot.
Available Shutter Speeds
15", 13", 10", 8", 6", 5", 4", 3"2, 2"5, 2", 1"6, 1"3, 1", 0"8, 0"6, 0"5, 0"4, 0"3, 1/4, 1/5, 1/6,
1/8, 1/10, 1/13, 1/15, 1/20, 1/25, 1/30, 1/40, 1/50, 1/60, 1/80, 1/100, 1/125, 1/160, 1/200,
1/250, 1/320, 1/400, 1/500, 1/640, 1/800, 1/1000, 1/1250, 1/1600, 1/2000, 1/2500, 1/3200
• 2" indicates 2 seconds, 0"3 indicates 0.3 second ad 1/160 indicates 1/160
second.
• The fastest shutter speed when usie flh is 1/2000 second. The camera
automatically resets the shutter spe/2000 second if a faster shutter speed
is chosen.
• Depending on the zoom posion, some shutter speeds may not be available.
• When shutter speeds of 1.3 seconds or slower are used, images are
processed to reduce noise after being taken. A certain amount of
processing time may be needed before you can take the next shot.
• You should set [IS Mode] to [Off] when lowering the shutter speed and
shooting with a tripod (p. 168).
• When shutter speeds of 1.3 seconds or slower are used, the ISO speed
is fixed to
What if the aperture value appears in orange?
If the aperture value appears in orange when the shutter button is pressed
halfway, the scene has exceeded the correct exposure limits. Adjust the shutter
speed until the aperture value appears in white (Safety shift can also be used
(p. 103)).
102
Setting the Aperture Value
You can set the aperture to a value at which you want to shoot. The camera
will set the appropriate shutter speed for the aperture value you set.
Bstands for “Aperture value”, which refers to the size of the aperture
opening inside the lens.
Set the mode dial to B.
Adjust the setting.
z Turn the 5dial to set the aperture value.
Shoot.
Available Aperture Values
F2.7, F3.2, F3.5, F4.0, F4.5, F5.0, F5.6, F5.8, F6.3, F7.1, F8.0
• Depending on the zoom position, some apertue values may not be available.
What if the shutter speed aars in orange?
If the shutter speed appears in orhethe shutter button is pressed halfway,
the scene has exceeded te corrosure limits. Adjust the aperture value
until the shutter speed appars in white. Safety shift can also be used (see below).
Safety Shift
In Mand Bmodes, if you press the nbutton to display the 4tab, and
set [Safety Shift] to [On], the shutter speed or aperture value is automatically
adjusted for the correct exposure when it cannot otherwise be obtained.
Safety Shift is disabled when the flash is enabled.
103
Setting the Shutter Speed and Aperture
Value
You can manually set the shutter speed and aperture to shoot images with
the exposure you want. Dstands for “Manual”.
Set the mode dial to D.
Choose a setting.
z Press the obutton to choose the shutter
speed or aperture value.
z Turn the 5dial to set a value.
X The set exposure level appears on the
indicator. You can check the difference
against the standard exposure level.
X When the difference is more than ±2 stops,
Aperture Value
the set exposue level appears in orange.
Shutter Speed
When you pres the shutter button
halfwa2” or “+2” appears in orange.
Standard
Exposure Level
Exposure Level
Exposure Level
Indicator
• The standard exposure is calculated according to the metering method
chosen (p. 95).
• If you use the zoom or change the composition after making settings, the
exposure level may change.
• Depending on the shutter speed and aperture value set, the screen
brightness may change. If the flash is raised and set to h, the screen
brightness will not change.
• If you press the obutton while holding down the shutter button halfway,
the shutter speed or aperture value (whichever is not chosen in Step 2),
will automatically adjust to obtain the correct exposure (the correct
exposure may not be obtained depending on the settings).
104
Adjusting the Flash Output
In Dmode, you can choose 3 levels of flash output.
Set the mode dial to D.
Choose the flash output level.
z After pressing the mbutton, press the
opbuttons to choose X.
Complete the setting.
choose the flash output level, then press
the mbutton.
X Once set, Xwill appear on the screen.
• You can also set the flash output level by pressing the nbutton to
choose [Flash Control] (p. 99) in the 4ab, then choose [Flash Output]
and press the qrbuttons to choose a tting.
• In Mand Bmodes, you cathe fsh output level if you choose
[Flash Control] in the 4t, thet [Flash Mode] to [Manual].
• If you hold down the hbr more than 1 second, the setting screen
will appear. If you press tutton then immediately press the n
button when the fsh is raised, the setting screen will appear.
105
Saving Shooting Settings
You can save commonly used Shooting modes and settings to your
or
. Even if you switch Shooting modes or turn off the camera, settings that
usually cancel (self timer, etc.) will be saved.
Settings that Can be Saved
•
•
•
•
•
•
Shooting modes (G, M, Band D)
Items set in G, M, Bor D(pp. 78 – 104)
Items in the shooting menu
Zoom position
Manual focus position (p. 93)
My Menu items (p. 171)
Enter a Shooting mode and make
settings.
Choose [SavSettings].
z Press nbutton, choose [Save
gsn the 4tab, then press the m
Save the settings.
z Press the qrbuttons or turn the 5dial to
choose a destination, then press the m
button.
• To change part of the saved settings (except the Shooting mode), choose
or
settings will not be reflected in other Shooting modes.
• To return contents saved to or to the default settings, turn the
mode dial to or , then choose [Reset All] (p. 47).
and change the settings, then repeat Steps 2 – 3. These
106
Using Various Functions for
Shooting Movies
This chapter serves as a more advanced version of the “Shooting
Movies” and “Viewing Movies” sections in Chapter 1, and explains how
to use various functions for shooting and viewing movies.
•
•
This chapter assumes that you have set the mode dial to E. However,
even if the mode dial is set to a position other than E, movies can be shot
by pressing the movie button.
The latter half of the chapter explaining movie playback and editing
assumes that you have pressed the 1button to enter Playback mode.
107
Shooting Movies in EMode
Enter Emode.
z Set the mode dial to E.
Adjust the settings according to
your purposes (pp. 108 – 116).
Shoot.
z Press the movie button.
z To stop shooting the movie, press the
movie button again.
Changing the Movie Mode
You can choose among 3 different Movie modes.
Choose a Moie mode.
z After png the mbutton, press the
buns to choose E.
z he qrbuttons or turn the 5dial to
button.
E
Standard
Shoots standard movies.
Shoots movies that can be edited with iFrame*1 compatible
software*2 or devices. The recording pixel setting will be fixed
iFrame Movie
at
Super Slow Motion Shoots fast moving subjects and plays them back in slow
Movie motion (p. 111).
(p. 113).
*1 Video type advocated by Apple.
*2 You can quickly edit and save iFrame movies if you use the included software.
108
Shooting Various Kinds of Movies
Just as with still images, you can let the camera select the best settings for
the scene or add various effects while shooting movies.
Choose a Shooting mode.
on p. 64 to choose a Shooting mode.
Shoot.
z Press the movie button.
X Depending on the Shooting mode or movie
image quality (p. 113) you choose, black
bars may appear on the top and bottom of
I
J
w
O
P
t
Portrait
Landscape
Beach
p. 61
p. 61
p
p.
p62
p. 63
iniature Effect
Monochrome
Super Vivid
p. 110
p. 67
p. 64
p. 64
p. 67
p. 68
Foliage
Snow
Poster Effect
Color Accent
Color Swap
T
Y
Fireworks
• You can also record movies in other Shooting modes by pressing the
movie button.
• Certain settings made in the FUNC. and Shooting menus will
automatically change to match settings for shooting movies.
109
Shoot Movies That Look Like a Miniature
Model (Miniature Effect)
You can shoot movies that look like moving miniature models. You create the
miniature model effect by choosing the upper and lower portions of the scene
that will be blurred, and the playback speed, which makes people and objects
in the scene move quickly during playback. Audio will not be recorded.
Choose
.
z Follow Steps 1 – 2 on p. 64 to choose
X A white frame (the area that will not be
blurred) appears on the screen.
.
Choose the area to keep in focus.
z Press the lbutton.
z Move the zoom lever to change the frame
size, and press the opbuttons to change
the frame posion.
Che playback speed.
z Phe nbutton.
5
z Press the qrbuttons or turn the
dial to
choose a playback speed.
z Press the nbutton to complete the
setting and restore the shooting screen.
Shoot.
z Press the movie button.
z To stop shooting the movie, press the
movie button again.
Playback Speeds and Estimated Playback Times
(for 1 Min. Clips)
Speed
Playback Time
Approx. 12 sec.
Approx. 6 sec.
Approx. 3 sec.
110
Shooting Super Slow Motion Movies
• The image quality will be fixed at
chosen, and
when an aspect ratio of
is chosen (p. 55).
is
when an aspect ratio of
• If you press the mbutton in Step 2, the horizontal/vertical orientation of
the frame will switch, and you can press the qrbuttons to change the
frame position when it is displayed vertically.
• Holding the camera vertically will change the orientation of the frame.
• Since you may not achieve the expected results depending on the
shooting conditions, try taking some test shots first.
Shooting Super Slow Motion Movies
You can shoot fast moving subjects and play them back in slow motion. Audio
will not be recorded.
Choose
.
z Follow the teps for “Changing the Movie
Moon p. 108 to choose
.
oe a frame rate.
r pressing the mbutton, press the
opbuttons to choose
.
z Press the qrbuttons or turn the 5dial to
choose an option, then press the m
button.
X The option you set will appear on the
screen.
Shoot.
z Press the movie button.
X The bar showing the shooting time will
appear. Maximum clip length is approx. 30
sec.
z To stop shooting the movie, press the
movie button again.
111
Shooting Super Slow Motion Movies
Frame Rates and Playback Times (for 30 Sec. Clips)
Frame Rate
240 fps
Playback Time
Approx. 4 min.
Approx. 2 min.
120 fps
Viewing super slow motion movies
• The movie will play back in slow motion when you follow Steps 1 – 3 on p. 32.
• You can use the included software to change the playback speed of movies shot
in
mode. Refer to the Software Guide for details.
• The recording pixel setting will be fixed at
(320 x 240 pixels) when
.
shooting in
, and
when shooting in
• Even if you move the zoom lever, the zoom will not operate while
shooting.
• The focus, exposure and white balance will be set when the movie button
is pressed.
112
Changing the Image Quality
You can choose among 3 different image quality settings.
Choose the image quality setting.
z After pressing the mbutton, press the
opbuttons to choose
.
Choose an option.
z Press the qrbuttons or turn the 5dial to
choose an option, then press the
button.
m
X The option you set will appear on the
screen.
Image Quality and Shooting Time per Memory Card
Memory Card Capacity
4 GB 16 GB
Image RecordingPixels,
Quality Frame Rate
Content
24 frames/sec.
1280 x 720 pixels, For shih-
30 frames/sec. definit) movies.
definition (HDvies.
40 sec.
Approx. 20 min.
43 sec.*1
Approx.1 hr.
24 min. 54 sec.*2
640 x 480 pixels, For shooting standard Approx. 43 min. Approx. 2 hr.
30 frames/sec. efinion (SD) movies. 43 sec. 59 min. 03 sec.
*1 Approx. 13 min. 35 sec. for iFrame movies (p. 108).
*2 Approx. 55 min. 38 sec. for iFrame movies (p. 108).
• Based on Canon’s testing standards.
• Recording will automatically stop when the clip file size reaches 4 GB, or when the
recording time reaches approximately 29 minutes and 59 seconds when shooting in
or
, and approximately 1 hour when shooting in
.
• Recording may stop even if the maximum clip length has not been reached on some
memory cards. SD Speed Class 6 or higher memory cards are recommended.
In
and
, black bars appear on the top and bottom of the screen.
These areas cannot be recorded.
113
Taking Still Images while Shooting a
Movie
You can shoot still images while shooting a movie.
Focus while shooting a movie.
z Make sure that 4appears on the screen,
then press the shutter button halfway.
X The focus and exposure will readjust (the
camera will not beep).
X The movie will continue shooting.
Shoot.
z Press the shutter button fully.
X The still image will be recorded.
What if you cannot take a still image?
You may not be able to take still images when thiting speed to the memory
card is slow, or when there is insufficient inmemory. In
and
modes,
will appear on the screen while shoting movie and you will not be able to
shoot still images.
• 4(blinking): Processing reorded . You can shoot when the icon stops
blinking.
•
: Still images cannot be taken
• A still image with an aspect ratio of
will be recorded when shooting in
will be recorded when shooting in
and
• A still image with an aspect ratio of
aspect ratio).
• If the aspect ratio setting for still images differs from the aspect ratio
(
aspect ratio).
(
.
• The shutter sound and black screen that occur when shooting a still
image will be recorded in the movie.
• The flash will not fire.
• The shooting date and time (p. 52) cannot be recorded in the image.
• The ISO speed will switch to
.
• i-Contrast (p. 79) is not available.
• If shooting still images fills the internal memory, the movie may stop
recording.
114
AE Lock/Exposure Shift
You can lock the exposure or change it in 1/3 steps within a range of –2 to +2
before shooting.
Lock the exposure.
z Press the obutton to lock the exposure.
The exposure shift bar appears.
z Press the obutton again to release the
lock.
Change the exposure.
z While watching the screen, turn the 5dial
to adjust the exposure.
Shoot.
z Press the movie button.
z To stop shoting the movie, press the
movie butagain.
Sound Settings
Adjusting the Recording Volume
You can manually set the recording volume for shooting movies.
z Press the nbutton to choose [Movie
Audio] in the 4tab, then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [Mic Level], then press the qr
buttons to choose [Manual].
The recording volume is
Auto
automatically adjusted to reduce
sound distortion.
After pressing the pbutton, press
the qrbuttons to set the sound
recording level (recording volume).
Manual
115
Other Shooting Functions
Using the Wind Filter
Wind Filter suppresses noise when the wind is strong. However, unnatural
sound may result when used to record in locations with no wind.
z Press the nbutton to choose [Movie
Audio] in the 4tab, then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [Wind Filter], then press the qr
buttons to choose [On].
Other Shooting Functions
The following functions can be used in the same way as for still images.
may not have any effect.
• Zooming in More Closely On Sub
The sound of zoom operations will rded.
• Using the Self-Timer (p. 53
The number of shots cannot e se
• Adjusting the White Balance (p. 80)
• Changing the Tone of an Image (My Colors) (p. 81)
• Shooting Close-ups (Macro) (p. 84)
• Shooting with the AF Lock (p. 91)
• Shooting in Manual Focus Mode (p. 93)
• Shooting Using a TV as the Display (p. 175)
• Turning Off the AF Assist Beam (p. 165)
• Customizing Display Information (p. 167)
• Changing the IS-Mode Settings (p. 168)
You can switch between [Continuous] and [Off].
• Registering Functions to the
Button (p. 170)
116
Editing
You can trim the beginnings and ends of recorded movies.
Choose *.
z Follow Steps 1 – 3 on p. 32 to choose *,
then press the mbutton.
X The movie editing panel and the movie
editing bar will appear.
Movie Editing Panel
Set the editing range.
z Press the opbuttons to choose
or
.
z If you press the qrbuttons or turn the 5
dial to move
,
will appear at points
where the ovie can be edited. If you
choose you can trim the beginning of
the ie from
n tm the end of the movie from
. If you choose
, you
.
Movie Editing Bar
n if you move to a point other than a
, only the portion from the nearest
to the left will be trimmed when
is
chosen. Only the portion from the nearest
to the right will be trimmed when
chosen.
is
Check the edited movie.
z Press the opbuttons to choose
, then
press the mbutton. The edited movie will
play.
z To edit the movie again, repeat Step 2.
z To cancel editing, press the opbuttons
to choose
. After pressing the m
button, press the qrbuttons or turn the
5dial to choose [OK], then press the m
button again.
117
Editing
Save the edited movie.
z Press the opbuttons to choose
press the mbutton.
, then
z Press the opqrbuttons or turn the 5
dial to choose [New File], then press the
mbutton.
X The movie will be saved as a new file.
• When [Overwrite] is chosen in Step 4, the unedited movie is overwritten
with the edited movie, erasing the original.
• When there is not enough space left on the memory card, only [Overwrite]
can be chosen.
• If the battery is depleted partway through saving, the edited movie clips
may not be saved.
• When editing movies, you should use a fully charged battery, or an AC
adapter kit (sold separately) (p. 212).
118
Using Various Playback and
Editing Functions
This chapter explains various ways to play back and edit images.
•
Press the 1button to enter Playback modbefore operating the camera.
• It may not be possible to play baor edit images that have been edited
on a computer, have hafile names changed, or have been taken
on a different camera.
• The edit function (p. 139 – 143) cannot be used if the memory card does
not have enough free sace available.
119
Quickly Searching Images
Searching Images Using Index Display
Displaying multiple images at the same time lets you quickly find the image
you want.
Move the zoom lever toward g.
X Images will display in an index.
z The number of images increases each
time you move the lever toward g.
z The number of images decreases each
time you move the lever toward k.
Choose an image.
z Turn the 5dial to switch images.
z Press the opqrbuttons to choose an
image.
X An orange frae appears on the chosen
image.
z thmbutton to display the chosen
iby itself.
Searching Images by Scrolling
Turning the 5dial will display images in a line letting you quickly search
them. You can also jump by the shooting date (Scroll Display).
Choose an image.
z If you set the camera to single image
playback and turn the 5dial quickly, the
images will display as shown on the left.
Turn the 5dial to choose an image.
z Press the mbutton to restore single
image playback.
z
Press the opbuttons during scroll display
to search images by the shooting date.
To turn off this effect, press the nbutton to choose [Scroll Display] in
the 1tab, then choose [Off].
120
Viewing Images in Filtered Playback
Viewing Movies Made with Movie Digest
You can select movies made in
mode (p. 70) by date for viewing.
Choose [Movie Digest Playback].
z After pressing the nbutton, choose
[Movie Digest Playback] in the 1tab, then
press the mbutton.
Choose a movie date.
z Press the opbuttons or turn the 5dial.
Play the movie.
z Press the mbutton.
X The movie will play.
Viewing Images in ered Playback
When there are many images omemory card, you can filter and display
them by a specified filterYou co protect (p. 128) or erase (p. 132)
images at once while filteed.
Jump to Favorites
Jump Shot Date
Displays the images tagged as favorites (p. 134)
Displays the images shot on a specified date.
Jump to My Category Displays the images of a specified category (p. 135).
Jump to Still/Movie
Jump 10 Images
Jump 100 Images
Displays still images, movies or movies shot in
Jumps over 10 images at a time.
mode
Jumps over 100 images at a time.
121
Viewing Images in Filtered Playback
Search by
,
,
and
Choose a target filter.
z In single image playback, press the d
button, then press the opbuttons to
choose a jump method.
z In
,
or
, press the qrbuttons to
choose a filter. Turning the 5dial will only
display images that match the filter of the
chosen target image.
Target Filters
z Press the lbutton to switch between
Information Display and No Information
Display.
z Press the nbutton to restore single
image playback.
View the filted images.
z Press tmbutton to start filtered
ckThe jump method and a yellow
frwill appear.
z If you press the qrbuttons or turn the 5
dial, the chosen target images will display.
z If you press the dbutton, [Filtered
playback settings cleared] appears on the
screen. Press the mbutton to cancel
filtered playback.
Filtered playback
In filtered playback (Step 2), you can view filtered images with “Quickly Searching
Images” (p. 120), “Viewing Slideshows” (p. 124), and “Magnifying Images”
(p. 125). You can process all filtered images at once while performing operations
in “Protecting Images” (p. 128), “Erasing Images” (p. 132), or “Choosing Images
for Printing (DPOF)” (p. 152), by choosing all of the filtered images.
However, if you change the category (p. 135), or edit an image and save it as a
new image (p. 139), a message will appear, and filtered playback will cancel.
122
Checking the Focus
Jump by
and
Images
z In single image playback, press the d
button, then press the opbuttons to
choose a jump method.
z If you press the qrbuttons, the display
will advance to the image that is the
chosen number of images away.
z Press the nbutton to restore single
image playback.
Checking the Focus
You can magnify the area of a recorded image that was inside the AF Frame
to check the focus.
Press the lbutton to switch to
the fs check display (p. 40).
whe frame will appear where the AF
me was when the focus was set.
X A gray frame will appear on a face
detected during playback.
X The area within the orange frame appears
magnified.
Switch frames.
z Move the zoom lever toward konce.
X The screen shown on the left will appear.
z Press the mbutton to move to a different
frame when multiple frames appear.
Change the magnification level or
location.
z
Use the zoom lever to change the display
size, and the opqrbuttons to change the
display position while checking the focus.
z Press the nbutton to reset the
display to Step 1.
123
Viewing Slideshows
The focus check display is not available for movies.
Viewing Slideshows
You can automatically play back images recorded to a memory card.
Choose [Slideshow].
z Press the nbutton to choose
[Slideshow] in the 1tab, then press the
mbutton.
Choose a setting.
z Press the opbuttons or turn the 5dial
to choose a menu item, then press the qr
buttons to adjt the setting.
Repeat
Repeas playback of images
me Display time for each image
Transition effects when switching
between images
Effec
Choose [Start].
z
Press the opbuttons or turn the
to choose [Start], then press the
5
dial
button.
m
X The slideshow will start a few seconds
after [Loading image...] appears on the
screen.
z You can pause/restart a slideshow by
z Press the nbutton to stop the
slideshow.
• If you press the qrbuttons or turn the 5dial during playback, the image
will switch. If you keep the qrbuttons pressed, you can fast-forward
through images.
• The power saving function (p. 48) does not work during slideshows.
• You cannot change [Play Time] if [Bubble] is chosen in [Effect].
• In single image playback, you can also start a slideshow by pressing and
holding the mbutton and immediately pressing the
button.
124
Magnifying Images
Move the zoom lever toward k.
z The display will zoom in on the image. If
you continue to hold the zoom lever, it will
zoom in up to a maximum factor of
approximately 10x.
z If you press the opqrbuttons, you can
move the location of the displayed area.
z Move the zoom lever toward gto zoom
out, or continue to hold it to return to single
image playback.
z If you turn the 5dial, you can switch
images while zoomed.
Approximate Location of
Displayed Area
playback.
• Movies cannot be magnified.
Viewing Each Ime in a Group
Grouped images taken in
mode (p. 74) can also be viewed individually.
Choose an image group.
z Press the qrbuttons or turn the 5dial to
choose an image that displays
,
then press the mbutton.
View each image in the group.
z If you press the qrbuttons or turn the 5
dial, only the grouped images will display.
z If you press the dbutton, [Display all
images] will appear on the screen. Press
the mbutton to exit group playback.
125
Viewing Each Image in a Group
Group playback
In group playback (Step 2), you can search (p. 120) and magnify (p. 125) images.
You can process all the images in a group at once while in “Protecting Images”
(p. 128), “Erasing Images” (p. 132), or “Choosing Images for Printing (DPOF)”
(p. 152), by choosing a set of grouped images.
Ungrouping Images
Grouped images taken in
mode can be ungrouped and viewed
individually.
Choose [Group Images].
z Press the nbutton to choose [Group
Images] in the 1tab.
Che a setting.
z Prthe qrbuttons to choose [Off].
z Press the nbutton to complete the
setting and restore single image playback.
X Grouped images taken in
mode are
ungrouped and appear individually.
z To regroup the images, follow the steps
above to choose [On].
Grouping cannot be canceled while viewing images individually (p. 125).
126
Displaying Various Images
(Smart Shuffle)
The camera will choose 4 images based on the displayed image. If you
choose one of those images, the camera will select 4 more images letting you
enjoy playing back images in an unexpected order. This will work best if you
take many shots of various scenes.
Choose [Smart Shuffle].
z Press the nbutton to choose [Smart
Shuffle] in the 1tab, then press the m
button.
X Four images will appear as possibilities.
Choose an image.
z Press the opqrbuttons to choose the
image you ant to view next.
X Thosen mage will be displayed in the
centand the next 4 possibilities will
pear.
ss the mbutton to display the center
image at full size. Press the mbutton
again to restore the original display.
z Press the nbutton to restore single
image playback.
• Only still images shot with this camera will play back in Smart Shuffle.
• [Smart Shuffle] is not available in the following situations:
- If there are less than 50 images taken with this camera on the memory card
- If you play back images not supported by Smart Shuffle
- During filtered playback
127
Changing Image Transitions
You can choose from 3 transition effects when switching between images in
single image playback.
Choose [Transition].
z Press the nbutton to choose
[Transition] in the 1tab, then press the
qrbuttons to choose a transition effect.
Protecting Images
You can protect important images so that they cannot be accidentally erased
with the camera (pp. 29, 132).
Choosing a Selection Method
Chse Protect].
z he nbutton to choose
[Protect] in the 1tab, then press the m
button.
Choose a selection method.
to choose a selection method, then press
the mbutton.
z Press the nbutton to complete the
setting and restore the menu screen.
If you format the memory card (pp. 23, 159), protected images will also be
erased.
Protected images cannot be erased with the camera’s erase function. To
erase an image, cancel protection settings first.
128
Protecting Images
Choosing Images Individually
Choose [Select].
z Follow Step 2 on p. 128 to choose [Select],
then press the mbutton.
Choose images.
z Press the qrbuttons or turn the 5dial to
choose an image, then press the m
button.
X
will appear on the screen.
z Press the mbutton again to deselect the
image. will disappear.
z To choose additional images, repeat the
above procedure.
Protect thimage.
z If yess te nbutton, a
nfirmation screen will appear.
ss the qrbuttons or turn the 5dial to
choose [OK], then press the mbutton.
If you switch to Shooting mode or turn off the camera before performing the
operations in Step 3, images will not be protected.
129
Protecting Images
Selecting a Range
Choose [Select Range].
z Follow Step 2 on p. 128 to choose [Select
Range], then press the mbutton.
Choose a starting image.
z Press the mbutton.
z Press the qrbuttons or turn the 5dial to
choose an image, then press the
button.
m
Choose an ending image.
z Press the rbutton to choose [Last image],
then press the mbutton.
z Press the qrbuttons or turn the 5dial to
choose an image, then press the
button.
m
z You cannot choose images before the first
image.
130
Protecting Images
Protect images.
z Press the pbutton to choose [Protect],
then press the mbutton.
Choosing images with the 5dial
screen in Steps 2 and 3 is displayed.
Choosing All Images
Choose [All Images].
z Follow Ste2 on p. 128 to choose [All
Imas], thn press the mbutton.
oteimages.
5
ss the opbuttons or turn the
dial
to choose [Protect], then press the m
button.
You can unlock groups of protected images if you choose [Unlock] in Step
4 in “Selecting a Range”, or Step 2 in “Choosing All Images”.
131
Erasing Images
You can erase all images at once. Since erased images cannot be recovered,
exercise adequate caution before erasing. Protected images (p. 128) cannot
be erased.
Choosing a Selection Method
Choose [Erase].
z Press the nbutton to choose [Erase]
in the 1tab, then press the mbutton.
Choose a selection method.
z Press the opbuttons or turn the 5dial
to choose a seection method, then press
the mbutton
z Press nbutton to restore the
sceen.
Choosing Images Individually
Choose [Select].
z Follow Step 2 above to choose [Select],
then press the mbutton.
Choose an image.
z If you follow Step 2 on p. 129 to choose
images,
z Press the mbutton again to deselect the
image. will disappear.
will appear on the screen.
z To choose additional images, repeat the
above procedure.
132
Erasing Images
Erase.
z If you press the nbutton, a
confirmation screen will appear.
z Press the qrbuttons or turn the 5dial to
choose [OK], then press the mbutton.
Selecting a Range
Choose [Select Range].
z Follow Step 2 on p. 132 to choose [Select
Range], then press the mbutton.
Choose images.
z Follow Stes 2 and 3 on p. 130 to choose
imags.
ase
ss the pbutton to choose [Erase],
en press the mbutton.
Choosing All Images
Choose [All Images].
z Follow Step 2 on p. 132 to choose [All
Images], then press the mbutton.
Erase.
z Press the qrbuttons or turn the 5dial to
choose [OK], then press the mbutton.
133
Tagging Images as Favorites
When you tag images as favorites, you can easily categorize just those
images. You can also filter out just those images for viewing, protecting or
erasing (p. 121).
Choose [Favorites].
z Press the nbutton to choose
[Favorites] in the 1tab, then press the m
button.
Choose an image.
5
z Press the qrbuttons or turn the
dial to
choose an image, then press the
m
button.
X
will appear on the screen.
z Press thmtton again to untag the
image. disappears.
z ooe additional images, repeat the
aprocedure.
Cmplete the setting.
z If you press the nbutton, a
confirmation screen will appear.
z Press the qrbuttons or turn the 5dial to
choose [OK], then press the mbutton.
If you switch to Shooting mode or turn off the camera before completing the
setting in Step 3, images will not be tagged as favorites.
If you use Windows 7 or Windows Vista and transfer tagged images to the
computer, they will be given a star rating of 3 (
movies).
) (except for
134
(My Category)
You can organize images into categories. You can display the images in a
category in filtered playback (p. 121) and process all images at once by using
the functions below.
•
“Viewing Slideshows” (p. 124), “Protecting Images” (p. 128), “Erasing
Images” (p. 132), “Choosing Images for Printing (DPOF)” (p. 152)
Images are automatically categorized by shooting condition as they are
shot.
: Images with detected faces, or images shot in I.
: Images detected as
J, or O.
: Images shot in
,
or
in Amode, or images shot in
, w, Por t.
Choosing a Selection Method
Choose [My Category].
z Prehe nbutton to choose [My
Catry] in the 1tab, then press the m
ton
Choose a selection method.
z Press the opbuttons or turn the 5dial
to choose a selection method, then press
the mbutton.
z Press the nbutton to restore the
menu screen.
135
Organizing Images by Category (My Category)
Choosing Images Individually
Choose [Select].
z Follow Step 2 on p. 135 to choose [Select],
then press the mbutton.
Choose an image.
z Press the qrbuttons or turn the 5dial to
choose an image.
Choose a category.
z Press the opbuttons to choose a
category, then press the mbutton.
X
will appear on the screen.
z Press the mbutton again to deselect the
image. will disappear.
z To chooaddional images, repeat the
above edure
Cote the setting.
z If you press the nbutton, a
confirmation screen will appear.
z Press the qrbuttons or turn the 5dial to
choose [OK], then press the mbutton.
If you switch to Shooting mode or turn off the camera before completing the
setting in Step 4, images will not be tagged as My Category.
136
Organizing Images by Category (My Category)
Selecting a Range
Choose [Select Range].
z Follow Step 2 on p. 135 to choose [Select
Range], then press the mbutton.
Choose images.
z Follow Steps 2 and 3 on p. 130 to choose
images.
Choose a category.
z Press the pbutton to choose an item,
then press the qrbuttons or turn the 5
dial to choose a category.
Complete the setting.
z Presthe button to choose [Select],
thess thmbutton.
If you choose [Deselect] in , you can deselect all of the images in the
[Select Range] category.
137
Rotating Images
You can change the orientation of an image and save it.
Choose [Rotate].
z Press the nbutton to choose [Rotate]
in the 1tab, then press the mbutton.
Rotate the image.
z Press the qrbuttons or turn the 5dial to
choose an image.
of the mbutton.
z Press the nbutton to restore the
menu screen.
• Movies with an image quality setti
o
cannot be rotated.
• Images cannot be rotated (p) if uto Rotate] is set to [Off].
138
Resizing Images
You can resize images to a lower pixel setting and save the resized image as
a separate file.
Choose [Resize].
z Press the nbutton to choose
[Resize] in the 1tab, then press the m
button.
Choose an image.
5
z Press the qrbuttons or turn the
dial to
choose an image, then press the
m
button.
Choose an image size.
5
m
z Press the qrbuttons or turn the
choose an ption, then press the
button.
dial to
X [Saew image?] will appear on the
cre.
Sthe new image.
z Press the qrbuttons or turn the 5dial to
choose [OK], then press the mbutton.
X The image will be saved as a new file.
Display the new image.
z When you press the nbutton,
[Display new image?] will appear on the
screen.
z Press the qrbuttons or turn the 5dial to
choose [Yes], then press the mbutton.
X The saved image will be displayed.
• You cannot resize an image to a larger size.
• Images saved as in Step 3 cannot be edited.
• Movies cannot be edited.
139
Trimming
You can cut out a portion of a recorded image and save it as a new image file.
Choose [Trimming].
z Press the nbutton to choose
[Trimming] in the 1tab, then press the m
button.
Choose an image.
5
m
z
Press the qrbuttons or turn the
choose an image, then press the
dial to
button.
Adjust the trimming area.
Trimming Area
X A frame will appear around the portion of
the image to be trimmed.
X The original image will display in the upper
left and the trimmed image will display in
the lower right
z Move toom ever to change the frame
size.
z the opqrbuttons to move the
f
Trimming Area Display
z Press the lbutton to change the
frame orientation.
Recorded pixels after
trimming
z In an image with detected faces, gray
frames appear around the faces located in
the upper left image. The frames can be
frames by turning the 5dial.
z Press the mbutton.
Save as a new image and display.
z Follow Steps 4 and 5 on p. 139.
• Images recorded at a pixel setting of
(p. 57), or images resized to
(p. 139) cannot be edited.
• Images that can be trimmed will have the same width and height ratio
after trimming.
• The number of recorded pixels in a trimmed image will be smaller than
before trimming.
• Movies cannot be edited.
140
Adding Effects with the My Colors
Function
You can change the color of an image and save it as a separate image. Refer
to p. 81 for details on each menu item.
Choose [My Colors].
z Press the nbutton to choose [My
Colors] in the 1tab, then press the m
button.
Choose an image.
5
z Press the qrbuttons or turn the
dial to
choose an image, then press the
m
button.
Choose an option.
5
m
z Press the qrbuttons or turn the
chooe an ption, then press the
but
dial to
z Follow Steps 4 and 5 on p. 139.
If you repeatedly change the color of the same image, the quality will
gradually deteriorate and you may not achieve the expected color.
• The color of images changed with this function may vary from those
recorded with the My Colors function (p. 81).
• My Colors settings cannot be applied to movies.
141
Correcting the Brightness (i-Contrast)
The camera can detect areas in an image, such as faces or backgrounds, that
are too dark and automatically adjust them to the optimum brightness. Also,
when the overall image is lacking in contrast, the camera will automatically
correct the image for a sharper impression. You can choose from 4 levels of
correction, and save the image as a new file.
Choose [i-Contrast].
z Press the nbutton to choose [i-
Contrast] in the 1tab, then press the m
button.
Choose an image.
z Press the qrbuttons or turn the 5dial to
choose an image, then press the m
button.
Choose an option.
z Press rbttons or turn the 5dial to
chose option, then press the m
Save as a new image and display.
z Follow Steps 4 and 5 on p. 139.
• Under some conditions, the image may appear coarse or may not be
corrected properly.
• Repeatedly adjusting the same image may cause it to appear coarse.
What if the image wasn’t corrected by the [Auto] option as
well as you would like?
Choose [Low], [Medium] or [High] and adjust the image.
Movies cannot be corrected.
142
Correcting the Red-Eye Effect
You can automatically correct red eyes in images and save them as new files.
Choose [Red-Eye Correction].
z Press the nbutton to choose [Red-
Eye Correction] in the 1tab, then press
the mbutton.
Choose an image.
z Press the qrbuttons or turn the 5dial to
choose an image.
Correct the image.
z Press the mbutton.
X Red-eye detected by the camera will be
corrected and a frame will appear around
the correctd portion.
z You can mgnify or reduce the size of the
imsing he procedures in “Magnifying
ags” (p. 125).
as a new image and display.
z Press the opqrbuttons or turn the 5
dial to choose [New File], then press the
mbutton.
X The image will be saved as a new file.
z Follow Step 5 on p. 139.
• Some images may not be corrected properly.
• When [Overwrite] in Step 4 is chosen, the uncorrected image is
overwritten with the corrected data, erasing the original image.
• Protected images cannot be overwritten.
Movies cannot be corrected.
143
144
Printing
This chapter explains how to choose images for printing, and print
using a Canon-brand PictBridge compliant printer (sold separately).
Canon-Brand PictBridge Compliant Printers
•
This chapter uses Canon-brand SELPHY CP series printers in the
explanations. The displayed screens and available functions will differ
depending on the printer. Please also refer to the Printer User Guide.
145
Easy Print
You can easily print the pictures you take by connecting the camera to a
PictBridge compliant printer (sold separately) using the supplied interface
cable (p. 2).
Turn off the camera and printer.
Connect the camera to the printer.
z Open the cover and insert the cable’s
small plug firmly into the camera terminal
in the direction shown.
z Insert the cable’s large plug into the
printer. For connection details, refer to the
user guide provided with the printer.
Tuthe printer.
Turn on the camera.
z Press the 1button to turn on the camera.
X
will appear on the screen.
146
Printing Images
Choose an image.
z Press the qrbuttons or turn the 5dial to
choose an image.
Print images.
z Press the cbutton.
X Printing will start.
z If you want to print additional images,
repeat Steps 5 and 6 after printing has
completed.
z After printing has completed, turn off the
camera and printer, and unplug the
interface cable.
• Refer to p. 214 for Canon-brand PictBrige compliant printers (sold
separately).
• Index printing is not available otain Canon-brand PictBridge
compliant printers (sold ate).
Making Print Settings
Connect the camera to the printer.
z Follow Steps 1 – 5 on p. 146 to choose an
image.
z Press the mbutton to display the screen
on the left.
Choose a menu option.
z Press the opbuttons or turn the 5dial
to choose an option.
Choose the option settings.
z Press the qrbuttons to choose the option
setting.
147
Printing Images
Default
Date
Follows the printer’s settings.
Prints the date.
File No.
Both
Prints the file number.
Prints both the date and file number.
Off
Default
Off
—
Follows the printer’s settings.
—
On
Uses shooting information to optimize print settings.
Corrects red-eye.
Red-Eye1
No. of Copies Choose the number of copies.
Trimming
—
—
Choose the area for printing (p. 148).
Sets the paper size and layout (p. 149).
Paper Settings
Trimming and Printing (Trimming)
You can cut out a portion of an image for printing
Choose rimming].
z Stps 1 – 2 on p. 147 to choose
[Ting], then press the mbutton.
X A frame will appear around the portion of
the image to be trimmed.
Choose the trimming area.
z Move the zoom lever or turn the 5dial to
change the frame size.
z Press the opqrbuttons to change the
frame position.
z Press the lbutton to rotate the frame.
z Press the mbutton to complete the
setting.
Print images.
z In the screen in Step 1, press the op
buttons or turn the 5dial to choose
[Print], then press the mbutton.
148
Printing Images
they are too small.
• Trimming photos with embedded dates may not show the dates properly.
Choosing the Paper Size and Layout for Printing
Choose [Paper Settings].
z Follow Steps 1 – 2 on p. 147 to choose
[Paper Settings], then press the mbutton.
Choose a paper size.
z Press the opbuttons or turn the 5dial
to choose n option, then press the m
button.
Cose the paper type.
z Press the opbuttons or turn the 5dial
to choose an option, then press the m
button.
Choose the layout.
z Press the opbuttons or turn the 5dial
to choose an option, then press the m
button.
z Press the qrbuttons to set the number of
prints when [N-up] is chosen.
Print images.
149
Printing Images
Available Layout Options
Default
Follows the printer’s settings.
Bordered
Borderless
N-up
Prints with a border.
Prints without a border.
Selects how many copies of an image are printed on a sheet.
Prints ID photos.
ID Photo
Only images with a recording pixel setting of L and an aspect ratio of
4:3 can be chosen.
Choose the print size.
Choose from 3.5 x 5 in., postcard and wide sized prints.
Fixed Size
Printing ID Photos
Choose [ID Photo].
z Follow Steps 1 – 4 on p. 149 to choose [ID
Photo], then pss the mbutton.
Choose length of the long side
anhoside.
to choose an option.
z Press the qrbuttons to choose the
length, then press the mbutton.
Choose the printing area.
z Follow Step 2 on p. 148 to choose the
printing area.
Print images.
150
Printing Images
Printing Movies
Connect the camera to the printer.
z Follow Steps 1 – 5 on p. 146 to choose a
movie.
z Press the qrbuttons to choose c, then
press the mbutton to display the screen
on the left.
Choose a printing method.
z Press the opbuttons or turn the 5dial
to choose
to choose a printing method.
, then press the qrbuttons
Print images.
Printing Options for Movies
Single
Prints currently dispscee as a still image.
Prints a sequence of s from a specified scene on a single sheet of
paper. If [Cation] is set to [On], you can print the folder number, file
number, and te elpsed time for the frame at the same time.
Sequence
• Pressing the mbutton during printing will cancel printing.
• [ID Photo] and [Sequence] cannot be chosen on Canon brand PictBridge
compliant printers from CP720/CP730 and earlier models.
151
Choosing Images for Printing (DPOF)
You can choose up to 998 images on a memory card for printing and specify
settings such as the number of copies so that they can be printed as a batch
(p. 156) or processed at a photo developer service. These selection methods
comply with the DPOF (Digital Print Order Format) standards.
Movies cannot be chosen.
Choosing Images for Printing with the cButton
You can add images to the print list (DPOF) directly after shooting or during
playback by pressing the cbutton.
Choose an image.
z Press the qrbuttons or turn the 5dial to
choose an image.
Press the cutton.
Add imaes to the print list.
z he opbuttons to choose the
nuer of prints, then press the qr
buttons or turn the 5dial to choose [Add]
and press the mbutton.
z To cancel adding images, repeat Steps 1
and 2, and press the qrbuttons or turn
the 5dial to choose [Remove], then
press the mbutton.
You cannot add images to the print list when the camera is connected to
the printer.
152
Choosing Images for Printing (DPOF)
Print Settings
You can set the print type, date and file number. These settings apply to all
images chosen for printing.
Choose [Print Settings].
z Press the nbutton to choose [Print
Settings] in the 2tab, then press the m
button.
Choose a setting.
z Press the opbuttons or turn the 5dial
to choose a menu item, then press the qr
buttons to choose an option.
z Press the nbutton to complete the
setting and estore the menu screen.
Standard
Index
Prints 1 e per page.
Print Type
Pseval reduced size images per page.
Both
On
Off
On
Off
On
Off
Pth standard and index formats.
Prints the shooting date.
Date
—
Prints the file number.
File No.
—
Removes all print settings after printing.
—
Clear DPOF
data
• Some printers or photo developer services may not be able to reflect all
of the settings in the prints.
•
may appear when using a memory card with print settings set by a
different camera. If you change the settings using this camera, all the
previous settings may be overwritten.
• If [Date] is set to [On], some printers may print the date twice.
• With [Index] chosen, the [Date] and [File No.] options cannot be set to
[On] at the same time.
• The date will be printed in the style set in the [Date/Time] function in the
3tab, which can be chosen after you press the nbutton (p. 20).
153
Choosing Images for Printing (DPOF)
Choosing the Number of Copies
Choose [Select Images & Qty.].
z Press the nbutton to choose [Select
Images & Qty.] in the 2tab, then press
the mbutton.
Choose an image.
z Press the qrbuttons or turn the 5dial to
choose an image, then press the m
button.
X You will be able to set the number of print
copies.
z If you choose images in [Index],
appears on the screen. Press the m
button again to deselect the image.
disapp
will
See nmber of prints.
z Phe opbuttons or turn the 5dial
to set the number of prints (maximum 99).
z Repeat Steps 2 and 3 to choose other
images and the number of prints for each.
z You cannot set the number of copies for
index prints. You can only choose which
images to print (as shown in Step 2).
z Press the nbutton to complete the
setting and restore the menu screen.
154
Choosing Images for Printing (DPOF)
Select Range
Choose [Select Range].
z Follow Step 1 on p. 154 to choose [Select
Range], then press the mbutton.
Choose images.
z Follow Steps 2 – 3 on p. 130 to choose
images.
Make print settings.
then press the mbutton.
Set All Images to Print Once
Choo[Seect All Images].
olloStep 1 on p. 154 to choose [Select
mages], then press the mbutton.
Make print settings.
choose [OK], then press the mbutton.
Clearing All Selections
Choose [Clear All Selections].
z Follow Step 1 on p. 154 to choose [Clear
All Selections], then press the mbutton.
All selections will be cleared.
z Press the qrbuttons or turn the 5dial to
choose [OK], then press the mbutton.
155
Choosing Images for Printing (DPOF)
Printing chosen images (DPOF)
• When there are images added to the print list
(pp. 152 – 155), the screen on the left will appear
when you connect the camera to a PictBridge
compliant printer. Press the opbuttons to
choose [Print now], then press the mbutton to
easily print images added to the print list.
• If you stop the printer during printing and start
again, it will start from the next print.
156
Changing Camera Settings
You can customize convenient and commonly used functions in the 3tab
(p. 43).
Changing Sounds
You can change each of the camera’s operation sounds.
z Choose [Sound Options], then press the
mbutton.
z Press the opbuttons or turn the 5dial
to choose a menu item.
z Press the qrbuttons to choose an option.
Preset sounds
(cannot be modified)
1
Preset sounds
2
You can use the included software to
change the sounds (p. 2).
Even if you change the [Shutter Souwill nt be reflected in the shutter
sound option in (p. 74).
Turning Off Hints & Tip
When you choose an item in the FUNC. menu (p. 42) or MENU (p. 43), a
description of the function (hints and tips) is displayed. You can turn off this
function.
z Choose [Hints & Tips], then press the qr
buttons to choose [Off].
158
Changing Camera Settings
Low Level Memory Card Formatting
Perform low level formatting when [Memory card error] appears, the camera
does not operate properly, you think that the recording/reading speed of a
memory card has dropped, the continuous shooting speed slows down, or
recording suddenly stops while shooting a movie. As you cannot retrieve the
erased data, exercise adequate caution before formatting the memory card.
Choose [Low Level Format].
z Choose [Format], then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [Low Level Format], then press
the qrbuttons to display
.
z Press the opqrbuttons or turn the 5
dial to choose [OK], then press the m
butto.
Sart e low level format.
ss the opbuttons or turn the 5dial
choose [OK], then press the mbutton.
X Low level formatting starts.
X When low level formatting ends, [Memory
card formatting complete] will appear on
the screen.
Complete the low level format.
z Press the mbutton.
• Low level formatting may take longer than standard formatting (p. 23),
since all recorded data is erased.
• You can stop a low level format of a memory card by choosing [Stop].
When stopping low level formatting, the data will be erased but the
memory card can be used without problem.
159
Changing Camera Settings
Changing the Start-up Screen
You can change the start-up screen that appears when you turn on the
camera.
z Choose [Start-up Image], then press the
mbutton.
z Press the qrbuttons or turn the 5dial to
choose an option.
No start-up image
Preset images
1
(cannot be modified)
Preset images
2
You can set recorded images, and use the
included software to change the images.
Registering Recorded Images as the tart-up Screen
Enter Pback mode.
z the 1button.
Choose [Start-up Image].
z Choose [Start-up Image], then press the
mbutton.
z Press the qrbuttons or turn the 5dial to
choose [2], then press the mbutton.
Choose an image.
5
z Press the qrbuttons or turn the
dial to
choose an image, then press the
m
button.
z Press the qrbuttons or turn the 5dial to
choose [OK], then press the mbutton to
complete registration.
Any previously registered start-up image will be overwritten when
registering a new start-up image.
160
Changing Camera Settings
Register the start-up image or sounds with the included
software
The dedicated operation sounds and start-up images on the included software
can be registered to the camera. Refer to the Software Guide for details.
Changing the File Number Assignment
Images you shoot are automatically assigned file numbers in the order they
were taken, from 0001 – 9999, and saved to folders of up to 2,000 images.
You can change the file number assignment.
z Choose [File Numbering], then press the
qrbuttons to choose an option.
Even if you shoot using a new
memory card, the file numbers are
Continuus assigned consecutively until an
image with the number 9999 is
aken/saved.
If you replace the memory card
created, file numbering begins
o Reset
with 0001 again.
• If you use a memory card already containing images, the newly assigned
file numbers may continue the existing numbering for both [Continuous]
and [Auto Reset]. If you want to start over with file number 0001, format
the memory card before use (p. 23).
• Refer to the Software Guide for information regarding folder structure or
image types.
161
Changing Camera Settings
Creating Folders by Shooting Date
Images are saved into folders created each month, however, you can also
create folders by shooting date.
z Choose [Create Folder], then press the
qrbuttons to choose [Daily].
z Images will be saved into folders created
on each shooting date.
Changing the Lens Retract Time
For safety reasons, the lens retracts about 1 minute after pressing the 1
button when in a Shooting mode (p. 28). If you wnt the lens to retract
immediately when you press the 1button, set te retract time to [0 sec.].
z se ens Retract], then press the qr
to choose [0 sec.].
Turning Off the Power Saving Function
You can set the power saving function (p. 48) to [Off]. Setting it to [On] is
recommended to save battery power.
z Choose [Power Saving], then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [Auto Power Down], then press
the qrbuttons to choose [Off].
z If you set the power saving function to
[Off], be sure to turn the camera off after
use.
162
Changing Camera Settings
Setting the Screen Shut-Off Time
You can adjust the time the screen takes to shut off automatically (p. 48). This
also works when [Auto Power Down] is set to [Off].
z Choose [Power Saving], then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [Display Off], then press the qr
buttons to choose a time.
z In order to save battery power, you should
choose less than [1 min.].
Using the World Clock
When traveling abroad, you can record images with local dates and times
simply by switching the time zone setting. f yu pre-register the destination
time zones, you can enjoy the convence of not having to switch the Date/
Time settings.
To use the world clock, be sure t the date/time (p. 20) and your home
time zone beforehand.
Set the world time zone.
z Choose [Time Zone], then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [ World], then press the m
button.
z Press the qrbuttons or turn the 5dial to
choose the world time zone.
z To set daylight saving time (adds 1 hour),
press the opbuttons to choose
z Press the mbutton.
.
163
Changing Camera Settings
Choose the world time zone.
to choose [ World], then press the
nbutton.
X
will appear on the shooting screen
(p. 191).
If you change the date or time in the
setting (p. 21), your [
Home]
time and date will automatically change.
Changing the Displayed Units
You can change the units that display in the MF indicator (p. 93) and zoom
bar (p. 25) from m/cm to ft/in.
z Choose [Distace Units], then press the
qrbuttons to hoose [ft/in].
164
If you set the mode dial to G, you can change the settings in the 4tab
(p. 43).
Before attempting to shoot using a function explained in this section in
modes other than G, check if the function is available in those modes
(pp. 200 – 203).
Switching the Focus Setting
The camera focuses on whatever it is aimed at even when you do not press
the shutter button. However, you can set it so that the camera only focuses
when the shutter button is pressed halfway.
z Choose [Continuous AF], then press the
qrbuttons to choose [Off].
Since the camera focuses continuously
until you press the shutter button
halfay, it allows you to shoot without
On
misg photo opportunities.
The camera does not focus
f
continuously, thereby conserving
battery power.
Turning Off the AF Assist Beam
The lamp will automatically light to assist focusing in low light conditions when
you press the shutter button halfway. You can turn off the lamp.
z Choose [AF-assist Beam], then press the
qrbuttons to choose [Off].
165
Changing Shooting Function Settings
Changing the Flash Timing
You can change the timing of the flash and shutter.
z Choose [Flash Control], then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [Shutter Sync.], then press the
qrbuttons to choose a setting.
The flash fires right after the
shutter opens.
1st-curtain
The flash fires right before the
2nd-curtain
shutter closes.
Turning Off the Red-Eye Reduction Function
The red-eye reduction lamp lights in order to reduce he red-eye effect that occurs
when shooting in dark conditions with the flash. Yocan turn off this function.
z Cose lash Control], then press the m
z Phe opbuttons or turn the 5dial
o choose [Red-Eye Lamp], then press the
qrbuttons to choose [Off].
Changing the Image Display Time Right After
Shooting
You can change the length of time the images display right after shooting.
z Choose [Review], then press the qr
buttons to choose an option.
2 – 10 sec. Displays images for the set time.
The image displays until you press
the shutter button halfway.
Hold
Off
Images will not display.
166
Changing Shooting Function Settings
Changing the Way the Image Displays Right
After Shooting
You can change the way the image displays right after shooting.
z Choose [Review Info], then press the qr
buttons to choose an option.
Off
Displays the image only.
Displays detailed information
(p. 194).
Detailed
The area inside the AF frame is
magnified, allowing you to check
Focus Check the focus. The procedure is the
same as in “Checking the Focus”
(p. 123).
Customizing Display Informtion
You can change which information is dayed by switching between custom
displays with each press of the btton.
z Choose [Custom Display], then press the
mbutton.
z Press the opqrbuttons or turn the 5
dial to choose
,
,
or
, then
press the mbutton, and the lbutton
to change the custom display settings.
Custom display items with
display when the lbutton is pressed.
Also, cannot be set for the current
will not
custom display while making settings.
z Press the opqrbuttons or turn the
dial to choose an item, then press the
5
m
button.
display.
will appear on items that
X Items with
will display.
167
Changing Shooting Function Settings
Displays shooting information
(p. 191).
Shooting Info
Grid Lines
Histogram
A grid overlays the screen.
A histogram (p. 41) appears in
Shooting modes G, M, Band
D.
If you press the shutter button halfway and return to the shooting screen
from the custom display settings screen, the settings will not be saved.
• Gray items can also be set, however, they may not appear depending on
the Shooting mode.
• Grid lines will not be recorded on the image.
Changing the IS-Mode Settings
z Choose [IS Setings], then press the m
button.
z Press oputtons to choose [IS
e], ten press the qrbuttons to
an option.
Automatically sets the optimal
Continuous image stabilization for the scene
(Intelligent IS) (p. 193).
Image stabilization is only active at
Shoot Only*
the moment of shooting.
Off
Turns off image stabilization.
*
Setting changes to [Continuous] when shooting
movies.
If camera shake is too strong, attach the camera to a tripod. You should
also set the IS Mode to [Off] when the camera is attached to a tripod.
168
Changing Shooting Function Settings
Turning Off the Powered IS Function
Powered IS reduces subtle camera shake when shooting movies at max.
telephoto. However, when shooting while walking, or during long panning
shots, you should set Powered IS to [Off], as it may cause unexpected results
in these situations.
z Choose [IS Settings], then press the m
button.
z Press the opbuttons to choose
[Powered IS], then press the qrbuttons
to choose [Off].
[Powered IS] settings will be disabled if [IS Mode] is set to [Off].
169
Changing Shooting Function Settings
Registering Functions to the
Button
z Choose [Set Shortcut button], then press
the mbutton.
z Press the opqrbuttons or turn the 5
dial to choose the functions to register,
then press the mbutton.
z Press the
button to call up the
registered function.
• Choose
• When this
if you want to return the button to default settings.
symbol is shown on the bottom right of an icon, the
function cannot be used in the current Shooting mode or function setting.
• In , each press of the button records white balance data (p. 80),
and the white balance settings change to
.
• In %, each press of the
%will appear on the screen.
button will adjust and lock the focus, and
• If you press the
button in , the creen and viewfinder
displays will turn off. Try one of the wing to restore the displays:
- Press any button other than er button
- Change the camera’s verticazontal orientation
- Open and close the sreen
- Raise and lower the flah
170
Registering Commonly Used Shooting
Menus (My Menu)
You can register up to 5 items from commonly used shooting menus to the
tab, letting you quickly access these items from a single screen.
Choose [My Menu settings].
z Choose [My Menu settings] in the
tab,
then press the mbutton.
Choose the menu items to register.
z Press the opbuttons or turn the 5dial
to choose [Select items], then press the
mbutton.
z Press the opbuttons or turn the 5dial
to chse a menu to register (up to 5), then
pree mbutton.
wl appear.
cancel registration, press the m
button, and will disappear.
z Press the nbutton.
Change the order in which menu
items are displayed.
z Press the opbuttons or turn the 5dial
to choose [Sort], then press the mbutton.
z Press the opbuttons or turn the 5dial
to choose the menu item you want to
move, then press the mbutton.
z
Press the opbuttons or turn the
change the order, then press the
z Press the nbutton.
5
dial to
button.
m
• Gray items in Step 2 can also be set, however, they may not be available
depending on the Shooting mode.
• Choose [Set default view] and press the qrbuttons to choose [Yes]. My
Menu can now be displayed by pressing the nbutton when in a
Shooting mode.
171
Changing Playback Function Settings
You can adjust the settings in the 1tab by pressing the 1button (p. 43).
Turning Off the Auto Rotate Function
When you play back images on the camera, images shot in vertical
orientation automatically rotate and display vertically. You can turn off this
function.
z Select [Auto Rotate], then press the qr
buttons to choose [Off].
• Images cannot be rotated (p. 138) if you have set [Auto Rotate] to [Off].
Rotated images will also appear in their rinal orientation.
• In Smart Shuffle (p. 127), even if [Rotae] is set to [Off], images
taken vertically will be displayed velly, while rotated images will
appear in their rotated orien
Choosing the Image that First Displays in
Playback
z Choose [Resume], then press the qr
buttons to choose an option.
Resumes with the image last
Last seen
viewed.
Resumes with the most recently
shot image.
Last shot
172
Viewing Images on a TV
Using the separately sold Stereo AV Cable AVC-DC400ST (p. 213), you can
connect the camera to a TV to view images you have shot.
Turn off the camera and TV.
Connect the camera to the TV.
z Open the camera’s terminal cover and fully
insert the cable plug into the camera’s
terminal.
z Insert the cable plug fully into the video
input terminals as shown in the illustration.
White
Red
Yellow
Yellow
Turn on the TV and switch it to the
input the cable is connected to.
Red
White
Turn on e camera.
z he 1button to turn on the camera.
X Thage will appear on the TV (nothing
will appear on the screen of the camera).
z After you finish, turn off the camera and
TV, and unplug the cable.
What if the images don’t display correctly on the TV?
Images will not display correctly if the camera’s video output setting (NTSC/PAL)
does not match the TV system. Press the nbutton and choose [Video
System] in the 3tab to switch to the correct video system.
174
Viewing Images on a TV
Shooting Using a TV as the Display
You can use a TV to display the camera screen content while shooting.
•
•
To connect the camera to a TV, follow the Steps in “Viewing Images on a
TV” (p. 174).
Shooting procedures are the same as when using the camera screen.
TV display is not available when using HDMI Cable HTC-100 (sold
separately) to connect the camera to an HD TV.
Using the HDMI Cable (Sold Separately) with an
HD TV
Using the separately sold HDMI Cable HTC-100 (p. 213), you can connect
the camera to an HD TV to view images you have shot.
Turn off thcamera and TV.
nect the camera to the TV.
en the camera’s terminal cover and fully
insert the cable plug into the camera’s
terminal.
z Fully insert the cable plug into the TV’s
HDMI input terminal as shown.
Display images.
z Follow Steps 3 and 4 on p. 174 to display
the images.
The supplied interface cable or the separately sold stereo AV cable
(p. 213), and HDMI Cable HTC-100 cannot be plugged into the camera at
the same time. Doing so could damage the camera or cables.
Operation sounds will not play when connected to an HD TV.
175
Viewing Images on a TV
Using a TV Remote to Control the Camera
When you connect the camera to an HDMI CEC compatible TV, you can use
the TV’s remote control to operate the camera and play back images or view
slideshows. You may need to make settings on some TVs. For details, refer
to the user guide supplied with the TV.
Choose [Ctrl via HDMI].
z Press the nbutton to choose [Ctrl via
HDMI] in the 3tab, then press the qr
buttons to choose [Enable].
Connect the camera to the TV.
z Follow Steps 1 – 2 on p. 174 to connect the
camera to the TV.
Display images.
z Turn on the Tnd press the camera’s 1
button
X mae will appear on the TV (nothing
ear on the screen of the camera).
Ue the TV’s remote control.
z Press the remote control’s qrbuttons to
choose an image.
z Press the OK/Select button to display the
camera control panel. Press the qr
buttons to choose an item, then press the
OK/Select button again.
176
Viewing Images on a TV
Summary of the Camera Control Panel Displayed on the TV
Return
Closes the menu.
Displays groups of High-speed Burst HQ images (only
appears when grouped images are chosen).
Group playback
Play movie
Slideshow
Plays a movie (only appears when a movie is chosen).
Plays back images automatically. During playback, you can
press the remote control’s qrbuttons to switch images.
.
Index playback
Displays images in an index.
lChange display
Changes the screen display (p. 40).
• If you operate the controls on the camera, you will not be able to control
the camera with the TV’s remote control until you return to single image
playback.
• Some TVs may not be able to control the camera properly even though
they are HDMI CEC compatible.
177
Using Household Power
If you use AC Adapter Kit ACK-DC80 (sold separately), you can use the
camera without worrying about how much charge is left in the battery.
Turn off the camera.
Plug the cord into the coupler.
z Fully insert the plug into the coupler.
Terminals
Insert the coupler.
z Follow Step 2 on p. 17 to open the cover,
then insert the coupler as shown until it
locks into placwith a click.
z Close the cover ( ) making sure the
coupler cable fits into the coupler cable
port ( ).
z Slide the cover ( ) until it clicks into
place.
Cable
Connect the power cord.
z Connect the power cord to the compact
power adapter, then plug the other end into
a power outlet.
z Turn the camera on to use it.
z After you finish, turn off the camera and
unplug the power cord from the power
outlet.
178
Using the Lens Hood (Sold Separately)
Do not unplug the plug or power cord with the camera turned on. This could
erase images you have taken or damage the camera.
Using the Lens Hood (Sold Separately)
When shooting a backlit, wide-angle photo without using a flash, attach Lens
Hood LH-DC60 (sold separately) to reduce the amount of extraneous light
entering the lens.
Attach the hood.
z Align the notch ( ) on the lens hood with
the mark on the camera ( ), then turn the
lens hood in the direction of the arrow until
locked.
z To remove he lens hood, turn it in the
opposite diction.
z When not in use, align the notch ( ) on
the hood with the mark on the camera
(
), and turn the hood in the direction of
the arrow until locked as shown.
If you use the built-in flash with the hood attached, portions of the image
may appear darker.
The lens hood and a filter adapter cannot be attached to the camera at the
same time.
179
Using an Externally Mounted Flash
(Sold Separately)
You can make your flash photography even better with the use of a Speedlite
EX series flash (sold separately, p. 212). With Speedlite 320EX (sold
separately), you can use the LED light to shoot movies.
• When a Speedlite EX series flash is mounted, you cannot set the built-in
flash.
• Using a non-Canon brand flash (particularly a high-voltage flash) or flash
accessories may inhibit normal operation or damage the camera.
• Please also read the Speedlite EX series manual included with the flash.
• Some functions on Speedlite EX series flashes may not be available
when used with this camera.
Using the Hot Shoe Cap
Attach the case for the hot shoe
cap to the strp.
z Remove strafrom the camera.
z he strap through the back of the
c
z Attach the strap to the camera (p. 13).
Remove the hot shoe cap.
z Push ( ) and lift ( ) the cap to remove it.
z To avoid losing the cap when you remove
it, place it in the case you attached to the
strap.
Attaching the Hot Shoe Cap
z Attach the hot shoe cap to protect the hot
shoe when not using an externally
mounted flash.
z Slide ( ) and push down ( ) to attach
the cap.
180
Using an Externally Mounted Flash (Sold Separately)
Speedlite 580EX II/430EX II/320EX/270EX II/
270EX
These flashes enable you to shoot scenes brightly and allow for a wider range
of flash photography to suit your purposes.
Attach the flash to the hot shoe.
Turn the flash on, then turn the
camera on.
X A red happears on the screen (or the
viewfinder).
X When the flash is charged, its pilot lamp
will light.
Set the camera to G, M, Bor D
mode.
t thwhite balance to h(p. 80).
Configure the externally mounted
flash.
z Press the nbutton to choose [Flash
Control] in the 4tab, then press the m
button.
z Press the opbuttons or turn the 5dial
to choose an item, then press the qr
buttons to adjust the setting.
z The available settings differ depending on
the shooting mode and attached flash
(p. 183).
181
Using an Externally Mounted Flash (Sold Separately)
What if...
• What if you cannot perform the operations in Steps 4 and 5?
Set the camera to G, M, Bor Dmode.
• What if you cannot adjust settings for the built-in flash?
When a Speedlite EX series flash is mounted, the setting screen for the built-in
flash will not appear, and you will not be able to adjust settings.
• What if you cannot choose [Flash Control]?
If you have set the flash to stroboscopic flash (580EX II only), you cannot
choose [Flash Control].
Using Speedlite Bracket SB-E2 (Sold Separately)
Using the separately sold Speedlite Bracket SB-E2
prevents unnatural shadows from appearing on the
sides of objects when shooting from a vertical
position. However, depending on the angle, the
bracket may interfere ith opening the screen. Use
the camera wihe sceen closed and facing
outward.
• You can also display the settreen if you hold down the hbutton for
more than 1 second.
• Flash settings can only be canged in G, M, B, Dmodes. In all other
modes, the flash adjusts and fires automatically.
What if the 320EX's LED light does not automatically light?
The LED light will only function in low light conditions when shooting movies, or
when setting the camera to movie mode. In these situations,
the screen.
will appear on
If the camera is set to
mode, flash settings can be adjusted the same
as when in Gmode.
182
Using an Externally Mounted Flash (Sold Separately)
Configuring the Externally Mounted Flash
(Sold Separately)
You can set the following options when in G, M, Band Dmodes. In other
modes, only [Red-Eye Corr.] and [Red-Eye Lamp] can be set (the flash
adjusts and fires automatically).
Shooting modes
Item
Options
G M B D
Auto*1
Manual*2
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
–
{
{
{
{
{
{
{
{
{
{
{
{
{
–
Flash Mode
{
–
Flash Exp.Comp*3
–3 to +3
4
*
1/128*5 to 1/1 (in 1/3 steps)
{
{
{
–
Flash Output
Shutter Sync.
1st-curtain/2nd-curtain/Hi-speed
On
Slow Synchro
Off
Wireless Func.*6
Red-Eye Corr.
Red-Eye Lamp
On/Off
On/Off
On/Off
On
{
{
{
{
{
{
{
{
{
–
Safety FE*7
Off
{
{
Clear Flash Settings*8
*1 The flash will be set to E-TTmode.
*2 The flash will be set to Dmod
You can also set the flash to E-TTL mode, when in Dmode. In this case, the flash will fire at
the flash output set on the camera in combination with the flash exposure compensation
amount set on the flash.
*3 Flash exposure compensation can only be set when [Flash Mode] is set to [Auto], and the
value on the flash is set to [+0]. If the flash exposure compensation amount is changed on the
flash, the screen display will also change.
*4 The flash output can be adjusted if [Flash Mode] is set to [Manual]. The settings will be
synchronized on the flash.
*5 1/64 for Speedlite 430EX II, 320EX, 270EX II and 270EX.
*6 Settings aside from On/Off are set on the flash. Cannot be set on Speedlite 430EX II, 320EX,
270EX II or 270EX. Additionally, when set to [On], [Shutter Sync.] cannot be set to [2nd-
curtain]. Even if you set [Shutter Sync.] to [2nd-curtain], it will change to [1st-curtain].
*7 Can only be set if [Flash Mode] is set to [Auto].
*8 Resets settings to their default values. [Slow Synchro], [Safety FE], [Red-Eye Corr.] and [Red-
Eye Lamp] can also be returned to their default values using [Reset All] in the camera's 3
menu (p. 47).
If the camera is set to
mode, flash settings can be adjusted the same
as when in Gmode.
183
Using an Eye-Fi Card
Before using an Eye-Fi card, be sure to check whether Eye-Fi card use is
authorized in the country or territory of use (p. 16).
When you put a prepared Eye-Fi card into the camera, you can automatically
service.
Image transfer is a function of the Eye-Fi card. For details on how to setup
and use the card, and concerning problems transferring images, please refer
to the Eye-Fi card user guide, or contact the manufacturer.
Please keep the following things in mind when using an Eye-Fi card.
• Even if you set [Eye-Fi trans.] to [Disable] (p. 185), the Eye-Fi card may transmit
radio waves. Be sure to remove the Eye-Fi card from the camera before
entering areas that prevent unauthorized transmission of radio waves, such as
hospitals and airplanes.
• If you have trouble transferring images, check the card or computer settings.
For details, refer to the user guide supplied with the card.
• Depending on the connection status of the wireless network, it may take time to
transfer images, or image transfer may be iterupted.
• Due to its transfer function, the Eye-Fi d mabecome hot.
• Battery consumption will be quicker thnormuse.
• Camera operations will be slown inormal use. This may be resolved by
setting [Eye-Fi trans.] to [Disab
If you put an Eye-Fi card intthe camera, the connection status can be
checked in the shooting screen (information display) and playback screen
(simple information display).
(Gray)
Not connected
(Flashing white) Connecting
(White)
Connected
Transferring
Interrupted
(Animated)
Error retrieving Eye-Fi card info (Turn the camera off and on again.
If this continues to appear, there may be a problem with the card.)
will appear on transferred images.
• The power saving function does not work while transferring images
(p. 48).
• If
mode is chosen, the Eye-Fi connection will be interrupted.
Choosing another Shooting mode or entering Playback mode will reopen
the Eye-Fi connection, but movies made with
retransferred.
mode may be
184
Using an Eye-Fi Card
Checking Connection Information
You can check the Eye-Fi card’s access point SSID, or connection status.
Choose [Connection info].
z Press the nbutton to choose [Eye-Fi
Settings] in the 3tab, then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [Connection info], then press the
mbutton.
X The connection info screen will appear.
Disabling Eye-Fi Transfer
You can set the card to disable Eye-Fi transfr.
Cho[Disable] in [Eye-Fi trans.].
ss the nbutton to choose [Eye-Fi
ings] in the 3tab, then press the m
button.
z Press the opbuttons or turn the 5dial
to choose [Eye-Fi trans.], then press the
qrbuttons to choose [Disable].
What if [Eye-Fi Settings] does not appear?
[Eye-Fi Settings] will not appear when an Eye-Fi card is not inserted in the
camera, and when an Eye-Fi card’s write-protect tab is in the locked position. For
this reason, settings cannot be changed for Eye-Fi cards equipped with a write-
protect tab when the tab is in the locked position.
185
Troubleshooting
If you think there is a problem with the camera, first check the following. If the
Help Desk.
Power
You pressed the power button, but nothing happened.
• Confirm that the battery is the correct type, and is not depleted (p. 15).
• Confirm that the battery is properly inserted (p. 17).
• Confirm that the memory card/battery cover is securely closed (p. 17).
with a cotton swab and re-insert the battery several times.
Battery is consumed quickly.
• Battery performance decreases at low temperatures. Warm the battery, for example, by
placing it in your pocket with the terminal cover on.
Lens will not retract.
• Do not open the memory card/battery cover while the power is on. After closing the
memory card/battery cover, turn the power on then back off (p. 17).
TV output
Image is distorted or not showing on TV (74).
Shooting
Cannot shoot.
• When in Playback mode (p. 22), press the shutter button halfway (p. 24).
The screen is off (p. 26).
Screen does not display properly in dark places (p. 41).
Screen does not display properly while shooting.
movies.
horizontal bar may appear.
though the shutter button was pressed fully (p. 27).
appears when the shutter button is pressed halfway (p. 27).
• Set [IS mode] to [Continuous] (p. 168).
• Raise the flash and set it to h(p. 79).
• Increase the ISO speed (p. 81).
• Attach the camera to a tripod. Additionally, you should set [IS Mode] to [Off] when
shooting with a tripod (p. 168).
186
Troubleshooting
Image is blurred.
• Press the shutter button halfway to focus on the subject, then press fully to shoot
(p. 24).
• Shoot the subject within the focusing distance (p. 207).
• Set the [AF-assist Beam] to [On] (p. 165).
• Confirm that functions which you do not intend to use (macro, etc.) are not set.
• Shoot using the focus lock or AF lock (pp. 86, 91).
Even when you press the shutter button halfway, the AF frame does not
appear, and the camera does not focus.
button halfway, or repeatedly push the shutter button halfway, the AF frame will appear
and the camera will focus.
Subject is too dark.
• Raise the flash and set it to h(p. 79).
• Correct the brightness with exposure compensation (p. 78).
• Adjust the image with i-Contrast (pp. 79, 142).
• Use spot metering or AE Lock to shoot (pp. 95, 96).
Subject is too bright (overexposed).
• Lower the flash and set it to !(p. 26).
• Correct the brightness with exposure comsatio(p. 78).
• Use spot metering or AE Lock to shoot (p, 96).
• Reduce the light illuminating the s.
Image is dark even though the red (p. 27).
• Shoot within an appropriatdistance flash photography (p. 79).
• Correct the flash exposure ompnsation amount or flash output (pp. 98, 105).
• Increase the ISO speed (p. 81).
Image taken using the flash is too bright (overexposed).
• Shoot within an appropriate distance for flash photography (p. 79).
• Lower the flash and set it to !(p. 26).
• Correct the flash exposure compensation amount or flash output (pp. 98, 105).
Image appears rough or grainy.
• Shoot with the ISO speed on a lower setting (p. 81).
appear rough or grainy (p. 63).
Eyes appear red (p. 99).
• Set the [Red-Eye Lamp] to [On] (p. 166). When shooting with the flash, the lamp lights
(p. 38). It is more effective if the subject is looking directly at the lamp. Even better
results can be obtained by increasing the lighting in indoor settings or approaching
closer to the subject.
• Correct images with red-eye correction (p. 143).
187
Troubleshooting
Recording images to the memory card takes a long time, or continuous
shooting slows down.
• Perform a low-level format of the memory card in the camera (p. 159).
Cannot make settings for shooting functions or FUNC. menu.
Shooting movies
Correct shooting time does not display, or stops.
high speeds. Even when the shooting time does not display properly, the recorded
video will be the length that it was actually shot (pp. 23, 31).
The full buffer warning (p. 191) appeared on the screen and shooting ended
automatically.
The camera’s internal memory was insufficient. Try one of the following:
• Perform a low-level format of the memory card in the camera (p. 159).
• Change the image quality setting (p. 113).
• Use a memory card capable of recording at high speeds (p. 113).
Subject appears distorted.
• The subject may appear distorted if it passes quickly ront of the camera while
shooting. This is not a malfunction.
Playback
Cannot play back images or movies
• If the file name or folder structue is changed on a computer, you may not be able to
play back images or movies. Refr tthe Software Guide for information regarding
folder structure or file names.
Playback stops, or audio cuts out.
• Use a memory card that has had a low-level format performed on it with this camera
(p. 159).
• If you copy a movie to a memory card that reads slowly, playback may interrupt
momentarily.
• Depending on its capabilities, when playing movies on a computer, frames may drop or
the audio may cut out.
Computer
Cannot transfer images to a computer.
cable by reducing the transfer speed.
• After pressing the 1button to enter Playback mode, press and hold the nbutton
and the oand mbuttons together. In the screen that appears, press the qrbuttons
to choose [B], then press the mbutton.
Eye-Fi Card
Cannot transfer images (p. 184).
188
Screen
If error messages appear on the screen, try one of the following solutions.
No memory card
• The memory card is not installed in the correct direction. Install the memory card in the
correct direction (p. 17).
Memory card locked
• The SD memory card, SDHC memory card, SDXC memory card or Eye-Fi card’s write
protect tab is set to “LOCK”. Unlock the write protect tab (p. 17).
Cannot record!
Memory card error (p. 159)
correct direction, contact a Canon Customer Support Help Desk (p. 17).
Insufficient space on card
101, 107) or edit images (pp. 139 – 143). Erase te mages (pp. 29, 132) to open space
for new images, or insert an empty memrd (p17).
Change the battery pack. (p. 17
No Image.
• There are no images recoed on the emory card that can be displayed.
Protected! (p. 128)
Unidentified Image/Incompatible JPEG/Image too large./Cannot play back
AVI/RAW
been taken with a different camera may not display.
Cannot magnify!/Cannot play back this content in Smart Shuffle/Cannot
rotate/Cannot modify image/Cannot register this image!/Cannot modify/
Cannot assign to category/Unselectable image.
• Incompatible images cannot be magnified (p. 125), played back in Smart Shuffle
(p. 127), tagged as favorites (p. 134), rotated (p. 138), edited (pp. 139 – 143),
registered to the start-up screen (p. 160), categorized (p. 135), or added to a print list
(p. 152).
• Images manipulated on a computer, that have had their file name changed, or have
been taken with a different camera may not be magnified, played back in Smart Shuffle,
tagged as favorites, rotated, edited, registered to the start-up screen, categorized, or
added to a print list.
189
List of Messages That Appear on the Screen
• Movies cannot be magnified (p. 125), played back in Smart Shuffle (p. 127), edited
(pp. 139 – 143), added to a print list (p. 152), or registered to the start-up screen
(p. 160).
Invalid selection range
was before the starting image.
Exceeded selection limit
• You chose more than 998 images in print settings. Choose 998 or less images (p. 152).
• Print settings could not be saved correctly. Reduce the number of selected images and
try again (p. 152).
• You chose 501 or more images in Protect (p. 128), Erase (p. 132), Favorites (p. 134),
My Category (p. 135) or Print Settings (p. 152).
Communication error
• Images could not be transferred to the computer or printed due to the large amount of
card reader to transfer the images. Insert the memory card into the printer’s card slot to
print.
Naming error!
• The folder or image could not be created becthere s an image with the same file
name as the folder or image that the caera iempting to create, or the highest
possible file number has already been ed. n the 3menu, change [File
Numbering] to [Auto Reset] (p. 161) or the memory card (p. 23).
Lens Error
• This error can occur if you hold the les while it is in motion or when using it in a location
with excessive dust or sand in the air.
• If this error message continues to appear, contact a Canon Customer Support Help
Desk as there may be a problem with the lens.
A camera error was detected (Error number)
• If an error code appears directly after taking a picture, the shot may not have been
recorded. Check the image in Playback mode.
• If this error code reappears, note the Error number (Exx) and contact a Canon
Customer Support Help Desk as there may be a problem with the camera.
File Error
• Photos from other cameras or images that have been altered using computer software
may not be printable.
Print error
• Check the paper size settings. If this message appears when the settings are correct,
turn the printer off and back on, then make the settings again.
Ink absorber full
• Contact a Canon Customer Support Help Desk for an ink absorber replacement.
190
Information Displayed on the Screen
Shooting (Information Display)
The same information will display on the viewfinder.
Battery Charge Indicator
(p. 15)
93)Lop. 91),
(p.
Shooting Mode (p. 196),
Sene Icon (p. 192)
Flash Mode (pp. 26, 79,
98), LED Light (p. 182)
AF Frame (p. 86)
Aperture Value
(pp. 103, 104)
ExposureCompensation
Amount (p. 78)
Bar (p. 78)
i-Contrast (p. 79)
Camera Shake Warning
Camera Orientation*
White Balance (p. 80)
My Colors (p. 81)
AEB Shooting (p. 97),
Focus Bracketing (p. 92)
Drive Mode (p. 83)
Eye-Fi Connection
Status (p. 184)
Flash Exposure
(p. 115)
Metering Method (p. 95)
Histogram (p. 41)
Still Image Compression
(p. 56), Recording Pixels
(p. 56)
Recordable Shots (p. 57)
Self-Timer (pp. 53, 54)
Movie Recording Pixels
(p. 113)
Remaining Time (p. 113)
Digital Zoom
Magnification (p. 50) /
Digital Tele-converter
(p. 85)
Compensation / Flash
Spot AE Point Frame
(p. 95)
Date Stamp (p. 52)
ISO Speed (p. 81)
Grid Lines (p. 168)
AE Lock (p. 96),
FE Lock (p. 96)
Zoom Bar (p. 25)
Blink Detection (p. 100)
MF Indicator (p. 93)
Buffer Warning
Wind Filter (p. 116)
Movie Audio (p. 115)
Time Zone (p. 163)
Image Stabilization
(p. 168)
Shutter Speed
(pp. 102, 104)
Mercury Lamp
Correction (p. 58)
191
Information Displayed on the Screen
: Standard, : Held vertically
*
When shooting, the camera detects if it is held vertically or horizontally, and adjusts settings
accordingly for the best shot. It also detects orientation during playback, so you can hold the
camera in either orientation and it will automatically rotate images for correct viewing.
This function may not operate correctly when the camera is pointed straight up or down.
Scene Icons
In Amode, the camera displays an icon for the scene it has determined
and then automatically focuses and selects the optimum settings for subject
brightness and color.
Subject
People
Non-Human Subjects
Icon
Background
Color
With
Strong
Facial
When
Moving
When When
Moving Close
Background
Bright
Backlit
Shadows
Gray
—
—
Including Blue
Skies
Light Blue
Orange
Backlit
Sunsets
Spotlights
Dark
—
—
Dark Blue
WhenUsing
Tripod
*
—
*
—
* Appears when the scene is dark and the camera is attached to a tripod.
192
Information Displayed on the Screen
IS Mode Icons
Automatically sets the optimal image stabilization for the scene (Intelligent IS)
and displays the following icons when in Amode
Reduces camera shake when
shooting movies, including strong
camera shake that occurs when
shooting movies while walking
Reduces camera shake when
shooting still images.
(Dynamic Mode).
Reduces subtle camera shake
when shooting movies at max.
telephoto (Powered IS).
Reduces camera shake when
panning while shooting*.
Disables image stabilization when
the camera is attached to a tripod.
However, image stabilization may
be applied depending on the
Reduces camera shake for macro
photography (Hybrid IS).
shooting conditions.
* Appears on the screen when following the motion of bject while shooting (panning). While
following a subject moving horizontally, only l camra shake will be reduced (horizontal
image stabilization will be disabled). Additionhen shooting subjects moving vertically,
only horizontal camera shake will be d.
If [IS Mode] is set to [Off] (pimage stabilization will be disabled, and
icons will not appeaon the screen.
193
Information Displayed on the Screen
Playback (Detailed Information Display)
Movies (pp. 30, 32) High-
speed Burst HQ (p. 74),
Print List (p. 152)
My Category (p. 135)
Shooting Mode (p. 196)
ISO Speed (p. 81),
Playback Speed (p. 110)
Exposure Compensation
Amount (p. 78),
Exposure Shift Amount
(p. 115)
White Balance (p. 80)
Histogram (p. 41)
Eye-Fi Transmple
Battere Idicator
p. 15)
Metering Method (p. 95)
Displayed Image Number
/ Total Number of Images
Shutter Speed (Still
Images) (p. 102), Image
(Movies) (p. 113)
Flash (pp. 79, 98), Flash
ExposureCompensation
Amount (p. 98)
(pp. 84, 93)
File Size (pp. 57, 113)
Still Images: Recording
Pixels (p. 57)
Movies: Movie Length
(p. 113)
Protect (p. 128)
Favorites (p. 134)
My Colors (pp. 81, 141)
Red-Eye Correction
(pp. 99, 143)
Aperture Value
(pp. 103, 104)
Group Playback (p. 125),
Image Editing
(pp. 139 – 143)
Compression (Image
Quality) (p. 56) /
i-Contrast (pp. 79, 142)
Shooting Date and Time
(p. 20)
Mercury Lamp
Recording Pixels (pp. 56,
113), MOV (Movies)
Correction (p. 58)
Some information may not display when viewing images on a TV.
194
Information Displayed on the Screen
Summary of Movie Control Panel in “Viewing Movies” (p. 32)
Exit
Play
Slow Motion (You can use the qrbuttons or turn the 5dial to adjust the
speed. Sound will not play back.)
Skip Backward* (Continues to skip backward if you hold down the mbutton.)
Previous Frame (Rewind if you hold down the mbutton.)
Next Frame (Fast forward if you hold down the mbutton.)
Skip Forward* (Continues to skip forward if you hold down the mbutton.)
Edit (p. 117)
*
Appears when connected to a PictBridge compliant printer (p. 146).
c
* Displays the frame of approx. 4 sec. before or after the current frame.
You can skip forward and skip backward during movie playback by
pressing the qrbuttons.
195
Functions and Menu Lists
Shooting Modes
A
DBMG
Function
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Exposure Compensation (p. 78)
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
—
—
{
{
{
{
{
—
{
—
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
{
{
—
{
—
{
{
{
{
{
{
{
{
{
{
{
{
—
{
—
—
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
—
{
—
{
{
{
{
{
—
{
{
—
{
—
—
—
—
—
—
{
—
—
—
{
—
{
—
ISO Speed (p. 81)
Self-Timer (p. 53)
][$
*2
Delay
Self-Timer Settings (p. 54)
*3
Shots
h
*4
Flash (pp. 26, 79, 98)
5
*
Z
—
—
—
—
—
—
—
—
{
!
1
*
1
M
Av/Tv Settings (pp. 102, 103)
1
*
*7
AE Lock/FE Lock (p. 96)
{
{
{
{
{
{
AE Lock (Movie)/Exposure Shift (p. 115
AF Lock (when registered to the
Focusing Range (p. 84)
utton) (p. 1
1
*
1
*
1
*
1
*
—
e
(p. 93)/
AF Lock (p. 91)
1
*
1
*
{
{
{
{
—
—
1
*
1
*
Change AF Frame Position (p. 88)
Change AF Frame Size (p. 88)
Face Select (p. 94)
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
{
{
—
—
—
—
{
—
1
*
1
*
{
{
{
{
{
{
Tracking AF (pp. 28, 87)
Program Shift (p. 96)
*1 The available settings depend on the registered shooting modes.
*2 Cannot be set to 0 seconds in modes where the number of shots cannot be set.
*3 Fixed to 1 shot in modes where the number of shots cannot be set.
*4 Fixed to !when the flash is lowered, but selectable when the flash is raised.
*5 Cannot be set, but switches to Zdepending on the circumstances.
*6 Cannot be set, but switches to Zwhen the flash fires.
*7 FE Lock not available when set to !.
*8 Except for Eand
, AE lock and exposure shift are available only when shooting movies.
196
Functions and Menu Lists
K
E
x
v
T
E
Y
IJ
wOPt
{
{
{
{
{
{
—
{
{
{
—
—
—
{
{
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
—
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
—
{
—
—
—
{
{
—
—
—
—
—
{
—
{
—
{
{
—
{
—
—
—
{
{
—
—
—
—
—
{
—
{
—
{
{
—
{
—
—
—
{
{
—
—
—
—
—
{
—
{
—
{
{
—
{
—
—
—
—
—
—
{
—
—
—
{
{
{
{
{
{
—
{
{
{
{
—
—
—
{
—
—
—
{
{
{
{
{
{
—
{
{
{
{
{
—
—
—
—
—
—
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
—
{
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
{
{
{
{
{
—
{
{
{
{
—
—
—
{
{
—
{
—
{
{
—
{
{
{
—
—
{
{
—
—
—
—
{
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
—
{
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
—
{
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
—
{
{
{
{
{
{
—
{
{
{
{
{
{
—
—
—
—
—
{
{
{
{
—
{
—
{
{
{
{
{
{
—
—
—
—
—
{
{
{
{
—
{
—
{
{
{
{
{
{
—
—
—
—
—
—
{
{
{
—
{
—
{
{
{
—
—
—
—
{
—
—
{
{
{
{
{
—
{
—
{
{
{
—
—
—
—
{
—
—
{
{
{
{
{
—
{
—
{
{
{
—
—
—
—
{
—
—
{
—
{
{
{
6
*
—
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
—
—
{
{
{
{
{
{
{
{
{
{
—
{
{
—
{
—
{
{
{
—
—
{
{
{
—
—
—
{
—
—
—
—
{
—
—
—
—
{
—
—
—
{
{
{
—
—
—
—
—
—
—
{
{
{
—
—
{
{
{
—
—
{
{
{
—
—
{
{
{
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
{
{
—
—
—
{
{
{
—
—
{
{
{
—
—
{
{
{
—
—
{
{
{
—
—
{
{
—
—
—
{
{
—
—
—
{
{
—
—
{ Selectable, or set automatically. – Not selectable.
197
Functions and Menu Lists
FUNC. Menu
Shooting Modes
A
DBMG
Function
1
1
1
1
1
1
1
1
*
*
*
*
*
*
*
*
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
{
{
—
—
{
*2
White Balance (p. 80)
h
3
3
*
My Colors (p. 81)
*
1
1
*
*
{
{
{
{
—
—
4
*
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
{
—
{
{
{
{
—
{
{
{
{
{
{
—
{
{
{
{
{
—
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
—
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
—
—
{
{
{
{
{
{
{
—
{
{
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
—
—
—
—
{
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
—
{
—
—
{
—
{
{
{
—
{
{
{
{
{
—
—
Bracketing (pp. 92, 97)
Drive Mode (p. 83)
W
5
*
Flash Exposure Compensation (p. 98)
Flash Output Settings (p. 105)
Metering Method (p. 95)
Still Image Aspect Ratio (p. 55)
Recording Pixels (p. 56)
Compression Ratio (p. 56)
—
—
1
*
1
*
1
*
1
*
1
*
1
*
1
*
1
*
1
*
1
*
Movie Quality (p. 113)
—
—
—
—
*1 The available settings depend on the registered shooting modes.
*2 Not available in xand v.
*3 White balance is not selectable.
*4 Contrast, sharpness, color saturation, red, green, blue, and skin tone can be set in 5 levels.
*5 is set when in f, AF Lock, or t.
*6 Only and are available.
*7 Synchronizes with the aspect ratio setting and is automatically set (p. 111).
198
Functions and Menu Lists
K
E
x
v
T
E
Y
IJ
wOPt
{
{
{
{
{
—
—
{
{
—
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
{
{
—
—
{
{
{
{
{
{
—
—
{
{
—
—
{
{
—
—
{
{
—
—
{
{
{
{
{
{
—
—
{
{
—
—
{
{
—
—
{
{
—
—
{
{
—
—
{
{
—
—
{
{
—
—
{
{
{
—
{
{
{
—
{
{
—
—
{
{
—
—
{
{
{
—
—
—
—
—
—
—
{
—
—
—
—
—
—
—
{
{
—
{
—
—
{
—
—
{
—
{
{
—
{
{
—
{
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
—
—
—
—
{
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
—
—
—
—
{
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
—
—
—
—
{
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
—
{
—
—
—
{
—
—
{
—
—
—
{
{
{
{
—
—
{
—
—
{
—
—
—
—
{
—
—
{
—
—
—
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
—
—
—
{
—
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
{
{
—
{
{
{
—
{
{
{
{
{
—
—
{
—
—
{
—
—
—
—
{
—
—
{
{
—
{
{
{
{
{
—
—
{
—
—
{
—
—
{
—
—
{
—
—
—
{
{
{
{
—
—
{
—
—
{
{
{
—
—
—
—
{
—
—
{
{
{
—
—
{
—
—
{
—
—
—
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
—
{
{
—
—
—
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
—
{
{
—
—
—
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
—
{
{
—
—
—
{
{
{
{
—
—
{
—
—
{
{
{
—
—
{
—
{
{
—
—
—
{
{
{
{
—
—
{
—
—
{
—
—
—
—
{
—
—
{
{
—
{
{
{
{
{
—
—
{
—
—
{
—
—
—
—
{
—
—
{
{
—
{
{
—
{
—
—
—
{
—
—
{
—
—
—
—
{
—
—
{
{
—
{
{
—
—
—
{
{
6
*
{
—
—
—
{
—
7
*
7
*
—
—
{ Selectable, or set automatically. – Not selectable.
199
Functions and Menu Lists
A
DBMG
Function
*1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Face Detect
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
—
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
—
—
{
{
—
{
—
—
{
—
{
—
{
—
—
—
—
—
—
—
—
—
—
—
{
—
3
AF Frame (p. 86)
Tracking AF
FlexiZone/Center
Standard
*
*4
—
{
{
—
{
{
—
{
{
—
{
{
—
{
—
{
{
—
—
—
—
{
{
{
{
—
{
—
{
Digital Zoom (pp. 50, 85) Off
Digital Tele-converter (1.5x/2.0x)
On
Off
On
AF-Point Zoom (p. 90)
Servo AF (p. 91)
*5
Off
On
Off
On
Off
On
Off
Off
Continuous AF (p. 165)
AF-assist Beam (p. 165)
MF-Point Zoom (p. 93)
Safety MF (p. 93)
Auto
Flash Mod
Manual
Flash Exp. Comp
Flash Output
Shutter Sync.
Flash Control
(pp. 98, 99, 105, 166)
On
Red-Eye Corr.
Off
Red-Eye Lamp
On/Off
On
Safety FE
Off
Auto
Off
i-Contrast (p. 79)
Hg Lamp Corr. (p. 58)
On/Off
—
—
*1 Operation differs depending on the shooting mode when faces are not detected.
*2 The available settings depend on the registered shooting modes.
*3 Only available by pressing the obutton (p. 28).
*4 [FlexiZone] in G, M, Band Dmodes, and [Center] in all other modes.
*5 [On] when moving people are detected in Amode.
200
Functions and Menu Lists
K
E
x
v
T
E
Y
IJ
wOPt
{
—
{
{
{
—
—
{
—
{
{
—
{
{
—
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
—
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
—
{
{
{
{
—
—
{
—
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
—
{
{
{
{
—
—
{
—
{
—
—
{
{
—
{
{
—
{
{
—
{
—
—
{
—
{
{
—
—
—
—
{
{
{
{
—
—
{
—
{
—
—
{
{
—
{
{
—
{
{
—
{
{
—
{
—
{
{
—
—
—
—
{
{
{
{
—
—
{
—
{
—
—
{
{
—
{
{
—
{
{
—
{
{
—
{
—
{
{
—
—
—
—
{
{
{
{
—
—
{
—
{
{
{
—
{
—
{
{
—
{
{
—
{
{
{
{
{
{
—
—
—
—
—
—
—
—
—
—
—
{
—
{
—
—
—
{
—
—
{
—
{
{
{
{
{
—
{
{
{
—
—
—
—
—
—
—
—
—
—
—
{
—
{
{
{
—
{
—
{
{
{
{
—
{
{
{
{
{
{
{
{
—
—
—
{
{
{
{
—
{
—
—
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
{
{
{
{
—
—
{
—
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
—
—
—
—
{
{
{
{
—
—
{
—
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
—
—
—
{
{
{
{
—
—
{
—
—
—
{
{
{
—
—
{
—
{
—
{
—
—
{
—
—
—
—
—
—
—
—
—
—
—
{
—
—
—
{
—
{
—
—
{
—
{
{
{
{
—
{
—
{
{
—
—
—
—
—
{
{
{
—
—
{
—
—
—
{
—
{
—
—
{
—
{
{
{
—
{
{
{
{
—
—
—
—
—
{
{
{
—
—
{
—
—
—
—
—
{
—
—
{
—
{
{
{
{
{
—
{
{
{
{
—
—
—
—
—
{
{
{
—
—
{
—
{
—
{
—
{
—
—
{
—
{
{
{
{
{
—
{
{
{
{
—
—
—
—
—
{
{
{
—
—
{
—
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
—
—
{
{
{
—
—
{
—
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
—
—
{
{
{
—
—
{
—
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
—
—
{
{
{
—
—
{
—
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
—
—
—
{
{
{
—
—
{
—
{
—
{
{
{
—
—
{
—
{
{
—
{
{
—
{
{
{
—
—
—
—
—
—
—
—
—
—
—
{
—
{
—
{
{
{
—
—
{
—
{
{
—
{
{
—
{
{
{
—
—
—
—
—
—
—
—
—
—
—
{
—
{
—
{
—
{
—
—
{
—
{
{
—
{
{
—
{
{
{
—
—
—
—
—
—
—
—
—
—
—
{
—
{ Selectable, or set automatically. – Not selectable.
201
Functions and Menu Lists
A
DBMG
Function
Center
Spot AE Point (p. 95)
AF Point
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
—
{
On
Safety Shift (p. 103)
Off
Movie Audio (pp. 115, 116) Mic Level/Level/Wind Filter
Review (p. 166)
Off / 2 - 10 sec. / Hold
Off
Review Info (p. 167)
Detailed/Focus Check
On
Off
Blink Detection (p. 100)
Custom Display (p. 167)
Reverse Disp. (p. 19)
Shooting Info/Grid Lines/
Histogram
1
1
*
*
{
{
{
{
{
{
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
On
Off
Off
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
IS Mode
IS Settings (pp. 168, 169)
Only
Off
Powered S
Display Area (p. 51)
Date Stamp (p. 52)
Large/Mediu/Sall
Off
Date/Date & Time
Set Shortcut button (p. 170)
Save Settings (p. 106)
{
{
*1 The available settings depend on the registered shooting modes.
202
Functions and Menu Lists
K
E
x
v
T
E
Y
IJ
wOPt
{
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
—
{
—
—
—
{
{
{
{
{
—
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
—
{
—
—
—
{
{
{
{
—
—
{
—
—
—
{
{
{
{
{
—
{
—
—
—
{
—
{
{
{
—
{
—
—
—
{
{
{
{
{
—
{
—
—
—
{
{
{
{
{
—
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
{
{
{
{
{
—
—
—
{
{
—
—
{
—
{
—
—
—
{
{
—
—
{
—
{
—
—
—
{
—
—
—
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
—
{
—
{
{
—
{
—
{
—
{
{
—
{
—
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
—
{
—
{
—
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
{
{
{
{
{
—
{
—
{
{
{
{
—
{
{
{
{
—
{
—
{
{
{
{
—
{
{
{
{
—
{
—
{
{
{
{
—
{
{
{
{
—
{
—
{ Selectable, or set automatically. – Not selectable.
203
Functions and Menu Lists
3Set up Menu
Item
Content
Ref. Page
p. 44
Mute
On/Off*
Volume
Set all operation sounds (5 levels).
Set the sounds for each camera operation.
On*/Off
p. 44
Sound Options
Hints & Tips
LCD Brightness
Start-up Image
Format
p. 158
p. 158
p. 45
Sets screen brightness (5 levels).
Add an image as a start-up image.
Formats memory card, erasing all data
Continuous*/Auto Reset
p. 160
pp. 23, 159
p. 161
p. 162
p. 162
File Numbering
Create Folder
Lens Retract
Monthly*/Daily
1 min.*/0 sec.
Auto Power Down: On*/Off
Display Off: 10, 20 or 30 sec./1*2 or 3 min.
pp. 48, 162,
163
Power Saving
Time Zone
Home*/World
p. 163
p. 21
Date/Time
Date and time settings
m/cm*/ft/in
Distance Units
Video System
Ctrl via HDMI
p. 164
p. 174
p. 176
NTSC/PAL
Enable/isable*
Eye-Fi connecon settings (only appears when
Eye-Fi card is inserted)
Eye-Fi Settings
p. 184
Language
Choose display language.
p. 22
p. 47
Reset All
Returns camera to default settings.
* Default setting
My Menu Menu
Item
Content
Ref. Page
My Menu settings
Sets the items registered to My Menu.
p. 171
204
Functions and Menu Lists
1Playback Menu
Item
Content
Ref. Page
Movie Digest Playback Plays back movies made in Movie Digest mode.
p. 121
p. 127
p. 124
p. 132
Smart Shuffle
Slideshow
Erase
Starts Smart Shuffle.
Plays back images automatically.
Erases images (Select, Select Range, All Images).
Protects images (Select, Select Range, All
Images).
Protect
p. 128
Rotate
Rotates images.
p. 138
p. 134
p. 135
p. 142
p. 143
p. 140
p. 139
p. 141
p. 120
p. 126
p. 172
p. 172
p. 128
Favorites
Tags or untags images as favorites.
Categorizes images (Select, Select Range).
Corrects dark portions and contrast in still images.
Corrects red eyes in still images.
Trims portions of still image
Resizes and saves still ims.
Adjusts colors in sges.
On*/Off
My Category
i-Contrast
Red-Eye Correction
Trimming
Resize
My Colors
Scroll Display
Group Images
Auto Rotate
Resume
On*/Off
On*Off
Last sen*Last shot
Transition
Fade*/Scroll/Slide/Off
* Default setting
2Print Menu
Item
Content
Ref. Page
Displays printing screen (When connected to a
printer).
Print
—
Select Images & Qty. Chooses individual images for printing.
p. 154
p. 155
p. 155
p. 155
p. 153
Select Range
Chooses starting and ending images for printing.
Chooses all images for printing.
Cancels all settings for printing.
Sets the printing style.
Select All Images
Clear All Selections
Print Settings
205
Handling Precautions
This camera is a high-precision electronic device. Do not drop it or subject
it to strong impacts.
Never place the camera close to magnets, motors or other devices that
generate strong electromagnetic fields. Exposure to strong magnetic fields
may cause malfunctions or corrupt image data.
•
•
•
•
•
•
If water droplets or dirt become stuck on the camera or screen, wipe with
a dry soft cloth or eyeglass wiper. Do not rub or apply force.
Never use cleaners containing organic solvents to wipe the camera or
screen.
Use a commercially available blower brush to remove dust from the lens.
For stubborn dirt contact a Canon Customer Support Help Desk.
When you move the camera rapidly from cold to hot temperatures,
condensation may form on the internal or external surfaces of the camera.
To avoid condensation, put the camera in an airtight, resealable plastic bag
and let it adjust to temperature changes slowly before removing it from the
bag.
•
If condensation has formed on the camera, stp using it immediately, as
continued use may damage the cameremoe the battery and memory
card, and wait until the moisture has coletely evaporated before
resuming use.
206
Specifications
Image Sensor
Camera Effective Pixels..................Approx. 12.1 million pixels
Lens
Focal Length ...................................4.3 (W) – 150.5 (T) mm
(35mm film equivalent : 24 (W) – 840 (T) mm)
Zoom Magnification.........................35x
Focusing Range..............................0 cm (0 in.) – infinity (W), 1.4 m (4.6 ft.) – infinity (T)
• Macro 0 – 50 cm (W) (0 in. – 1.6 ft. (W))
Image Stabilizer (IS) System...............Lens-shift type
Imaging Processor ..............................DIGIC 5
Electronic Viewfinder...........................Effective dots: Approx. 202,000 (67,000 x 3)
• Dioptric adjustment and 5 levels of brightness
adjustment
LCD Monitor
Type ................................................TFT color (wide viewing angle type)
Size .................................................2.7 type
Effective Pixels................................Approx. 230,000 dots
Aspect Ratio....................................4:3
Features..........................................Brightness adjustent (5 levels), Quick-bright LCD
Variangle type (vement: approx. 175 degrees
horizonprox. 70 degrees rotational)
Focus
Control System................................us: ingle (Continuous in Auto mode), Servo AF/
SE
Manl Focus
AF Frame .....................................Face Detect, Tracking AF, Center, FlexiZone
Metering System..................................Evaluative, Center-weighted average, Spot
Exposure Compensation
(Still Images) /
Exposure Shift (Movies) ......................±2 stops in 1/3-stop increments
ISO Speed (Standard Output Sensitivity, Recommended Exposure Index)
............................................................Auto, ISO 100/200/400/800/1600/3200
White Balance .....................................Auto, Day Light, Cloudy, Tungsten, Fluorescent,
Fluorescent H, Flash, Custom
Shutter Speed......................................1 – 1/3200 sec.
15 – 1/3200 sec. (Total shutter speed range)
Aperture
Type ................................................Iris
f/number..........................................f/2.7 – f/8.0 (W), f/5.8 – f/8.0 (T)
207
Specifications
Flash
Modes .............................................Auto, on, Slow Synchro, off
Hot Shoe.........................................Available
Range .............................................50 cm – 7.0 m (W), 1.4 – 3.0 m (T)
(1.6 – 23 ft. (W), 4.6 – 9.8 ft. (T))
1
2
Shooting Modes ..................................C2, C1, M, Av, Tv, P, Auto* , Sports, SCN* , Creative
3
4
Filters* , Movie*
• Shooting movies is possible with the movie button
*1 Smart Auto also available for movies
5
*2 Movie Digest, Portrait, Landscape, Smart Shutter* ,
High-speed Burst HQ, Handheld Night Scene, Low
Light, Beach, Foliage, Snow, Fireworks, Stitch Assist
*3 Fish-eye Effect, Miniature Effect, Toy Camera Effect,
Monochrome, Super Vivid, Poster Effect, Color
Accent, Color Swap
*4 Standard, iFrame Movie, Super Slow Motion Movie
*5 Smile, Wink Self-timer, Face Self-timer
Digital Zoom........................................Still images/Movies: Approx. 4x (up to approx. 140x in
combination with the optical zoom)
Safety Zoom, Digital te-converter
Continuous Shooting
Mode Selection ...............................Continuous ng, cotinuous shooting AF
Speed..............................................Appr4 shs/sec. (In P mode)
Appshts/sec. (In High-speed Burst HQ mode)
Number of Shots (CIPA compliant) ...Approshots (Viewfinder)
Appox. 380 shots (LCD monitor)
Recording Media.................................SD memory card, SDHC memory card, SDXC memory
card
File Format..........................................Design rule for Camera File system, DPOF (Version 1.1)
compliant
Data Type
Still Images .....................................Exif 2.3 (JPEG)
Movies.............................................MOV (Image data: H.264; Audio data: Linear PCM
(stereo))
208
Specifications
Recording Pixels
Still Images......................................[16:9]
Large: 4000 x 2248, Medium 1: 2816 x 1584, Medium 2:
1920 x 1080, Small: 640 x 360
[3:2]
Large: 4000 x 2664, Medium 1: 2816 x 1880, Medium 2:
1600 x 1064, Small: 640 x 424
[4:3]
Large: 4000 x 3000, Medium 1: 2816 x 2112, Medium 2:
1600 x 1200, Small: 640 x 480
[1:1]
Large: 2992 x 2992, Medium 1: 2112 x 2112, Medium 2:
1200 x 1200, Small: 480 x 480
Movies.............................................[Super Slow Motion Movie]
*1
640 x 480 (120 fps when shooting, 30 fps during
*1
playback), 320 x 240 (240 fps when shooting, 30 fps
during playback)
[Miniature Effect]
1280 x 720 / 640 x 480
*2
*2
[iFrame Movie]
1
1280 x 720 (3fp
)
[Other thhe abve]
*1
1920 x 124 fps ) / 1280 x 720 (30 fps ) / 640 x 480
*1
)
l frame rate is 29.97 fps.
*ing: 6 fps, 3 fps, 1.5 fps Playback: 30 fps
3 Actual frame rate is 23.976 fps.
*1
Interface............................................Hi-Speed USB
HDMI output
Analog audio output (stereo)
Digital video output (NTSC/PAL)
Direct Print Standard ...........................PictBridge
Power Source......................................Battery Pack NB-10L
Compact Power Adapter CA-PS700
(when used with AC Adapter Kit ACK-DC80)
Dimensions (CIPA compliant)..............122.9 x 92.4 x 107.7 mm (4.84 x 3.64 x 4.24 in.)
Weight (CIPA compliant).....................Approx. 600 g (Approx. 21.2 oz.)
(Including the battery and memory card)
Approx. 557 g (Approx. 19.6 oz.) (camera body only)
209
Specifications
Battery Pack NB-10L
Type ....................................................Rechargeable lithium-ion battery
Nominal Voltage..................................7.4 V DC
Nominal Capacity ................................920 mAh
Charge Cycles.....................................Approx. 300 times
Operating Temperatures .....................0 – 40 °C (32 – 104 °F)
Dimensions..........................................32.5 x 45.4 x 15.1 mm (1.28 x 1.79 x 0.59 in.)
Weight .................................................Approx. 41 g (Approx. 1.4 oz.)
Battery Charger CB-2LC/CB-2LCE
Rated Input..........................................100 V – 240 V AC (50/60 Hz)
16 VA (100 V) – 22 VA (240 V)
0.18 VA (100 V) – 0.12 VA (240 V)
Rated Output.......................................8.4 V DC, 0.7 A
Charge Time........................................Approx. 1 hour 50 min. (When using NB-10L)
Charge Indicator..................................Charging: orange, Fully charged: green
(2 indicator system)
Operating Temperatures .....................0 – 40 °C (32 – 104 °F)
Dimensions..........................................93.8 x 63.0 x 27.0 mm 3.65 x 2.48 x 1.06 in.)
Weight .................................................Approx. 80 g (Appro.82 oz.) (CB-2LC)
Approx. 74 rox. 261 oz.) (CB-2LCE, excluding
powerd)
Lens Hood LH-DC60 (Sold Separat
Camera Mount..................................Bayonet pe
Max. Diameter x Length.......................φ696 x 27.0 mm (φ2.74 x 1.06 in.)
Weight .................................................Approx. 10 g (Approx. 0.35 oz.)
•
•
All data is based on tests by Canon.
Camera specifications or appearance are subject to change without notice.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATION.
210
Accessories
Supplied with
Camera
Neck Strap
NS-DC11
Battery Pack NB-10L
with Terminal Cover* CB-2LC/CB-2LCE*
Battery Charger
DIGITAL CAMERA
Solution Disk
Lens Cap
Case for Hot
Shoe Cap
(includes hot shoe cap)
Interface Cable
IFC-400PCU*
Also vailable for purchase separately.
Memory Card USB Card Reader
Windows/Macintosh
Canon-Brand PictBridge Compliant Printers
Stereo AV Cable AVC-DC400ST
HDMI Cable HTC-100
TV
211
Separately Sold Accessories
The following camera accessories are sold separately. Some accessories are
not sold in some regions, or may no longer be available.
Power Supplies
Battery Pack NB-10L
z Rechargeable lithium-ion battery.
Battery Charger CB-2LC/CB-2LCE
z A charger for charging Battery Pack NB-
10L.
AC Adapter Kit ACK-DC80
z This kit lets you power the camera using
household power. Recommended for
powering the camera for an extended
period of time or when connecting to a
computer or prnter. Cannot be used to
charge the cera battery.
Using accessories abroa
The battery charger and the AC adapcan be used in regions that have 100
– 240 V (50/60 Hz) AC power
If the plug does not fit the outle, usa commercially available plug adapter. Do
not use electrical transformers for foreign travel as they will cause damage.
Flash
Speedlite 580EX/430EX II/320EX/270EX II/
270EX
z A shoe-mounted flash that allows for a
wide range of flash photography.
Speedlite Bracket SB-E2
z Prevents unnatural shadows from
appearing on the sides of subjects when
shooting from a vertical position. The Off-
Camera Shoe Cord OC-E3 is supplied with
this bracket.
212
Separately Sold Accessories
Speedlite Transmitter ST-E2
z This allows the wireless control of slave
(remote) Speedlite flashes (except the
Speedlite 220EX and 270EX).
Other Accessories
Stereo AV Cable AVC-DC400ST
z Use this cable to connect to a TV for
shooting and viewing images.
HDMI Cable HTC-100
z Use this cable to connect the camera to
the HDMI trminal on a high-definition TV
set.
s Hod LH-DC60
vents extraneous light from entering
e lens and causing flares or ghosting,
which reduce image quality.
Filter Adapter FA-DC67A
z This adapter is required for attaching a
67 mm filter.
Canon-brand Lens Filter (67 mm dia.)
z Protects the lens and allows you to shoot
with various effects.
A lens filter and the lens cap cannot be attached to the camera at the same
time.
213
Separately Sold Accessories
Printers
Canon-Brand PictBridge Compliant
Printers
z By connecting your camera to a Canon-
brand PictBridge compliant printer, you
can print your images without having to
use a computer.
For more information, visit your nearest
Canon retailer.
SELPHY
Series
PIXMA
Series
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine
Canon accessories. Canon shall not be liable for any damage to this product and/or
accidents such as fire, etc., caused by the malfunction of non-genuine Canon
accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this
warranty does not apply to repairs arising out of the malunction of non-genuine Canon
accessories, although you may request such repairs n chargeable basis.
214
Index
DIGITAL CAMERA Solution Disk ................2
Digital Tele-Converter................................85
AF J Focus
AF Lock .....................................................91
AF-Point Zoom ..........................................90
Battery
Charge Indicator .................................15
Charging.............................................14
Battery Charger ...................................2, 212
Camera
Center (AF Frame Mode) ..........................86
Color Accent (Shooting Mode) ..................67
Compression Ratio (Image Quality) ..........56
Continuous Shooting .................................83
Continuous Shooting
Face Detect (AF Frame Mode)..................87
Face Select................................................94
Fish-eye Effect (Shooting Mode)...............65
Flash
High-speed Burst HQ
Flash Exposure Compensation...........98
Off.......................................................26
On.......................................................79
Slow Synchro......................................98
FlexiZone (AF Frame Mode) .....................86
Focus
(Shooting Mode) .................................74
Creative Filters (Shooting Mode)...............64
Custom White Balance..............................80
D
Date/Time
215
Index
AF Frames.................................... 26, 86
AF Lock .............................................. 91
AF-Point Zoom ................................... 90
Face Select......................................... 94
Servo AF............................................. 91
Focus Check ........................................... 123
Focusing Range
Macro.................................................. 84
Focus Lock................................................ 86
Foliage (Shooting Mode)........................... 62
Formatting (Memory Card)................ 23, 159
FUNC. Menu
M
Menu
Movies
Basic Operations ................................ 42
List.................................................... 198
Grid Lines................................................ 168
Handheld NightScene
Modes...............................................108
High-speed Burst HQ ............................. 74
I
iFrame Movie (Movie Mode).................... 108
Images
Playback J Viewing
Display Time..................................... 166
Editing J Editing
Erasing Images........................... 29, 132
Protecting ......................................... 128
Interface Cable.............................. 2, 35, 146
ISO Speed................................................. 81
Powered IS..............................................169
Power J Battery, AC Adapter Kit
Power Saving ............................48, 162, 163
Printing ....................................................146
Program AE...............................................78
Protect.....................................................128
L
Lamp ......................................... 38, 165, 166
Landscape (Shooting Mode) ..................... 61
LCD Monitor J Screen
216
Recording Pixels (Image Size) ..................56
Terminal.....................35, 146, 174, 175, 178
Travel Abroad............................16, 163, 212
SCN (Shooting Mode) ...............................61
Screen
Information Display...................191, 194
Cards
Mgnified Display .............................125
Changing Delay and Number of
Shooting
Shooting Time.....................................31
Smile (Shooting Mode)..............................71
Software
Wink Self-Timer (Shooting Mode) .............72
Z
Zoom ...................................................25, 50
Transferring Images to a Computer
for Viewing..........................................33
Sound Settings ..........................................44
Sports (Shooting Mode).............................60
Stereo AV Cable..............................174, 213
Stitch Assist (Shooting Mode) ...................76
Super Slow Motion (Movie Mode) ...........111
217
FCC Notice
(Digital Camera, Model PC1680 systems)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions;
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for Class B
digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diffent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/Thniciafor help.
The cable with the ferrite core provided the gital camera must be used with this
equipment in order to comply with Class iSubpart B of Part 15 of the FCC
rules.
Do not make any changes or modicatins to the equipment unless otherwise specified
in the manual. If such changes or modifications should be made, you could be required
to stop operation of the equipment.
Canon U.S.A., Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516) 328-5600
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
To ensure proper operation of this product, use of genuine Canon
accessories is recommended.
USA and Canada only:
The Lithium ion/polymer battery that powers the product is
recyclable.
Please call 1-800-8-BATTERY for information on how to
recycle this battery.
218
For CA, USA only
Included lithium battery contains Perchlorate Material - special handling
may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details.
Battery Charger CB-2LC
IMPORTANT SAFETY INSTRUCTIONS-SAVE
THESE INSTRUCTIONS.
DANGER-TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, CAREFULLY FOLLOW
THESE INSTRUCTIONS.
For connection to a supply not in the U.S.A., use an attachment plug
adapter of the proper configuration for the power outlet, if needed.
Battery Charger CB-2LCE
The adapter can be used with a power supplbetween 100 and 240 V AC.
Contact your Canon dealer for informn abut plug adapter for overseas
use.
For U.S.A. customers only: Foas here 120 V AC power is not used,
you will need a special plug a
For only United States
Use a UL listed, 1.8-3m(-10f), Type SPT-2 or NTSPT-2, AWG no.18
power supply cord, rated for 125V 7A, with a non-polarized NEMA 1-15P
plug rated for 125V 15A.
Trademark Acknowledgments
•
•
•
The SDXC logo is a trademark of SD-3C, LLC.
This device incorporates exFAT technology licensed from Microsoft.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
The iFrame logo and the iFrame symbol are trademarks of Apple INC.
•
About MPEG-4 Licensing
This product is licensed under AT&T patents for the MPEG-4 standard and
may be used for encoding MPEG-4 compliant video and/or decoding
MPEG-4 compliant video that was encoded only (1) for a personal and
non-commercial purpose or (2) by a video provider licensed under the AT&T
patents to provide MPEG-4 compliant video.
No license is granted or implied for any other use for MPEG-4 standard.
* Notice displayed in English as required.
219
Disclaimer
• Reprinting, transmitting, or storing in a retrieval system any part of this
guide without the permission of Canon is prohibited.
• Canon reserves the right to change the contents of this guide at any
time without prior notice.
• Illustrations and screenshots in this guide madiffer slightly from the
actual equipment.
• The above items notwithstanding, Caacceps no liability for
damages due to mistaken operof he products.
CDD-E453-020
© CANON INC. 2011
|
York Predator 102 User Manual
Vornado Aqs 35 User Manual
Technics Dp 2310 User Manual
Panasonic Kx Ft34hk User Manual
LG LRE30451S User Manual
KENWOOD K30CSS14 User Manual
England Stove Works Pellet Stove User Manual
CRAFTSMAN 917.270912 User Manual
CRAFTSMAN 247.203732 User Manual
ASUS X551M User Manual