Inspi
PP-310
CYCLONE
BATTERY PACK
User’s Manual
Introduction
Thank you for choosing the Bolt Cyclone PP-310 power pack. This
professional lithium-ion (Li-ion) battery pack powers a wide range of
flash units. You’ll never miss an important moment when you’re using
the Cyclone—this slender power pack offers speed and reliability, so
that you can always make the most of your time.
Outstanding features include:
• Lightning-fast recycle time of one second with popular flash
units such as the Canon Speedlite 600EX-RT, Nikon SB-910 AF
Speedlight, and Sony HVL-F60M.
• Up to 500 flashes per charge at full power, and up to thousands in
full automatic mode.
• Fast 2-hour charging time.
• Lightweight, compact, and durable build, featuring heat-resistant
nylon housing.
• Compatibility with battery pack systems and accessories from
popular brands such as Quantum, Lumedyne, Dynalite, and Impact.
|
Introduction 3
1
Overview
8
2
1
2
3
4
5
6
7
8
9
Power button
Multifunction socket cover
Multifunction socket
Shoulder strap lugs
Padded feet
3
4
4
Vent
7
Belt clip
Status, Charge, and battery indicator lights
Status LED
10 Charge LED
11 Battery LEDs
6
12 Shoulder strap
13 Shoulder strap quick release
14 DC car charger BO-1004
15 AC battery charger BO-1010
5
|
4 Overview
14
12
13
15
9
FULL
25%
75%
50%
STATUS
CHARGE
11
10
|
Overview 5
Warnings
⚠ ⚡
• Do not disassemble or attempt to maintain this product yourself. There are high-voltage components inside
the Cyclone. Contact can produce a dangerous electric shock.
• Keep out of reach of children.
• Do not touch the metal part of the multifunction socket.
•
Do not use this product in flammable conditions, such as environments containing flammable gases or liquid chemicals.
• This product is not water-resistant. Keep it away from rain, snow, and humidity.
• Do not store or use this product at temperatures above 104°F (40°C).
• Do not connect this product to a charger other than the included AC or DC charger.
• To avoid overheating and damaging your flash unit, please wait for at least 10 minutes after 40 continuous
flashes at full power. The Cyclone has a much higher power output than the typical built-in battery of a
flash unit. Refer to your flash unit’s manual for information on its continuous full-power flash capacity and
limitations.
• Remove any cable from the multifunction socket when the Cyclone is not in use or charging, and cover the
socket firmly with the multifunction socket cover.
•
Make sure the cable connected to the multifunction socket is firmly connected when using or charging the Cyclone.
|
6 Warnings
Charging Your Cyclone
The Cyclone offers a fast charging time of 2 hours and a charge-level indicator that’s easy to read at a glance.
To charge your Cyclone with the included charger:
Plug the charger unit into an AC outlet.
Plug the charger cable into the multifunction socket on the Cyclone.
Wait for all of the green battery LEDs to stop flashing and remain on.
To charge your Cyclone with the optional BO-1004 DC car charger:
Plug the charger unit into a compatible charger socket (cigarette lighter) in a car or other vehicle.
Plug the charger cable into the multifunction socket on the Cyclone.
Charging is completed when all of the green battery LEDs stop flashing and remain on.
To get the maximum capacity from your Cyclone:
Charge your Cyclone shortly before use to ensure that the pack retains the maximum charge. Lithium-ion
batteries gradually lose their charge when not in use.
Charge your Cyclone at a moderate room temperature, and avoid storing it in hot environments between
|
Charging Your Cyclone 7
charging and use. High temperatures can cause Lithium-ion batteries to drain more quickly when being
stored.
Note: When charging the pack outside of the United States, plug adapters may be used to plug the charger
into any 100-240 V AC power outlet.
Reading the indicator lights while charging:
While your Cyclone is charging, its red Charge LED will remain on, and its four green battery LEDs will flash in
sequence during the charging process. When the pack is fully charged, all four battery LEDs will remain on.
The Status LED remains off during charging. If the battery is not charged to its full capacity after 4 hours of
continuous charging, the Status LED will flash to indicate that the battery is faulty or has reached the limit of
its product life and can no longer hold a full charge. Please replace the Cyclone immediately if this occurs.
Checking the Cyclone’s charge level:
When the Cyclone is not charging and is not connected to a flash unit, its level of charge can be checked by
pressing the power button. The battery LEDs will illuminate to indicate the level of charge, as follows:
|
8 Charging Your Cyclone
Battery LED 1 on: 25% or lower charge level
Battery LEDs 1-2 on: 25%-50% charge level
Battery LEDs 1-3 on: 50%-75% charge level
Battery LEDs 1-4 on: 75% or higher charge level
FULL
25%
75%
50%
STATUS
CHARGE
Connecting Your Cyclone to Your Flash
You can use the Cyclone to power a wide range of flash units. To connect the Cyclone to your flash unit, you
must use a compatible connection cable. Cables sold by some flash and battery pack manufacturers are
interchangeable with Bolt cables, but other flash brands use a different connector type. Make sure you select
the right one.
Important! Load your flash unit with its standard batteries before connecting it to the Cyclone.
Most compatible flash units require the standard batteries to be installed in order to power the computer
functions that allow the flash to work.
You may need to set your flash unit to recycle by drawing power from the Cyclone only to avoid draining the
installed batteries. Check your flash unit’s manual for details on the relevant setting.
|
Connecting Your Cyclone 9
To connect your Cyclone to your flash unit:
1. Plug the 5-pin metal connector of the connection
cable firmly into the multifunction socket of the
Cyclone.
1
|
10 Connecting Your Cyclone
2. Plug the other end of the connection cable
securely into the compatible power port on your
flash unit.
2
3. Press the power button on the Cyclone and wait
for the Status and battery LEDs to turn on.
When the Cyclone is charged, connected to your
flash unit, and turned on, its Status LED will glow
amber and the battery LEDs will glow green to
indicate the charge level of the battery.
To disconnect your Cyclone from your flash unit:
1. Press the power button until the Status and battery LEDs turn off.
2. Unplug the connection cable from the battery pack.
Note: If you do not fire your flash for 60 minutes with the Cyclone connected, the battery pack will shut off
automatically.
|
Connecting Your Cyclone 11
Using Your Flash with Your Cyclone
Your Cyclone can recycle in just one second with many popular flash units to keep you shooting and ensure
that you don’t miss important moments. With your flash firing at full power, it can power up to 500 flashes,
depending on the specific unit you’re using. It can power thousands of shots in automatic mode with many
flash units.
To get the best use out of your Cyclone:
•
Use in environments with moderate temperatures. When lithium-ion batteries get cold, they lose some of
their ability to supply power. However, this does not mean that they have lost their charge, and they regain
the ability to supply power when their temperature returns to a more moderate level.
Don’t fire more than 40 full-power flashes in a row. Exceeding the recommended number can overheat and
even damage your flash. The Cyclone has a much higher power output than the typical built-in battery of a
flash unit. Refer to your flash unit’s manual for information on its continuous full-power flash capacity and
limitations.
•
Tip: If you’re shooting in a very cold environment, you can keep power flowing to your flash by alternating
two Cyclones: Keep one pack indoors at room temperature or in an interior pocket next to your body while
using the other pack, and then switch the two packs when the one in use starts losing its ability to power
your flash.
|
12 Using Your Cyclone
Reading the indicator lights while using the Cyclone:
When you’re using your Cyclone, its amber Status LED will remain on to indicate that the flash is ready to fire.
Its four green battery LEDs will indicate the level of charge as follows:
Battery LED 1 on: 25% or lower charge level
Battery LEDs 1-2 on: 25%-50% charge level
Battery LEDs 1-3 on: 50%-75% charge level
Battery LEDs 1-4 on: 75% or higher charge level
Battery LED 1 flashing: The Cyclone has been drained and needs to be charged.
Status LED flashing: The Status LED flashing indicates that the battery is overheated. Stop using the pack for
at least 10 minutes to allow it to cool.
Carrying and wearing the Cyclone:
The Cyclone is designed to be easy to carry and inconspicuous. Its light weight and compact design make it
easy to wear for long periods, and its black finish and clean design will complement your professional attire.
It also offers these convenient features:
|
Using Your Cyclone 13
•
•
Padded feet. Two rubberized feet give the Cyclone stability and protection when you set it down.
Belt clip. One of the easiest ways to carry the Cyclone is to attach it to your belt with the included clip.
When you won’t be carrying the pack on your belt, you can give it a cleaner profile by removing the clip.
To do this, loosen the screws using a Phillips screwdriver, remove the clip, then tighten the screws to
secure them.
•
Shoulder strap. Thread the shoulder strap through the built-in lugs on the Cyclone and through the strap clips
and buckles, as shown here. After threading it, pull it tight to take up any slack. Always make sure that your
strap is attached securely since dropping the Cyclone can damage it.
|
14 Using Your Cyclone
Troubleshooting
Problem
Solution
The Cyclone is charged and connected to a flash
The cable is damaged or you are using the wrong
with a cable, but no indicator lights illuminate when cable.
you turn it on.
The Cyclone is connected to the charger, and the
It will flash if the battery is not charged fully after
Charge indicator light is flashing instead of showing 4 hours of continuous charging, which indicates
a solid red light.
an overused or faulty battery. In this case, please
replace the battery immediately.
The Status indicator light is flashing.
The pack is overheated. Turn it off and wait for at
least 10 minutes before using it again.
The Cyclone is charged and connected to a flash
with a cable, but the flash does not fire.
Make sure you have AA or other internal batteries
installed in the flash. These may be required for its
computer functions to work.
Customer Service
|
Troubleshooting 15
Specifications
Cyclone Battery Pack PP-310:
Rated output: 12.6 V DC
Operation environment working temperature range:
-4°F - 104°F (-20°C - 40°C)
Operation environment working humidity:
85% or less
Dimensions (W × H × D): 1.4 × 3.34 × 1.78 inches
(35.5 × 85 × 45 mm)
Weight: 4.6 ounces (130 grams)
Power cord length: 58 inches (147 cm)
Battery type: Lithium-ion (Li-ion)
Output: 320V DC
Input: 11.1V
Capacity: 1900 mAh
Recycle time with hot-shoe-mounted flash units:
approx. one second (at full flash power)
Flashes per charge:
Up to 500 (at full flash power)
Operation environment working temperature range:
-4°F - 104°F (-20°C - 40°C)
Operation environment working humidity:
85% or less
Dimensions (including belt clip) (W × H × D):
4 × 5.9 × 1.7 inches (10.4 × 10 × 4.4 cm)
Weight: 14.1 ounces (400 grams)
DC car charger BO-1004:
Compatible battery pack: Cyclone PP-300 / PP-310
Rated input: 12-24 V DC
Rated output: 13.6 V DC 600mA
Operation environment working temperature range:
-4°F–104°F (-20°C–40°C)
Operation environment working humidity: 85% or less
Dimensions (W × H × D): 1. 375 × 1.25 × 3.375 inches
(35 × 32 × 86 mm)
Weight: 2.9 oz (82.2 grams)
Cord length: 57 inches (145 cm)
AC battery charger BO-1010:
Compatible battery pack: Cyclone PP-310
Recharging time: 2 hours for Cyclone PP-310
Rated input: 100-240 V AC
|
16 Specifications
ONE-YEAR LIMITED WARRANTY
Bolt provides a limited warranty to the original purchaser that this product is free from defects in materials and workmanship
under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement,
whichever occurs later. Bolt’s responsibility with respect to this limited warranty shall be limited solely to repair or replacement,
at Bolt’s discretion, of any product that fails during normal consumer use. Inoperability of the product or part(s) shall be
determined by Bolt. If the product has been discontinued, we reserve the right to replace it with a model of equivalent quality
and function.To obtain warranty coverage, contact Bolt to obtain a return merchandise authorization (“RMA”) number, and return
the defective product to Bolt, along with the RMA number and proof of purchase. Shipment of the defective product is at the
purchaser’s own risk.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or
maintenance. EXCEPTAS PROVIDED HEREIN, BOLT MAKES NEITHERANY EXPRESSWARRANTIES NORANY IMPLIEDWARRANTIES,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state.
Copyright © 2013 Gradus Group
Made in China
|
Warranty 17
Compatible Devices and Accessories
The Cyclone is compatible with a wide range of hot-shoe and handle-mount flash units. Make sure you select
a connection cable that is compatible with your flash unit.
Many compatible accessories are also available from Bolt and other brands. Bolt connection cables are
interchangeable with some other manufacturers’ battery pack connection cables.
These optional accessories are available from Bolt:
Bolt BO-1004 Replacement Car Charger
Bolt BO-1010 Replacement Charger
|
18 Compatible Devices
Bolt BO-1001 CZ Canon flash cable
Bolt USB-C Charger for Mobile Devices
Bolt BO-1002 CKE Nikon flash cable
Bolt BO-1005 Sony Flash Cable
|
Compatible Devices 19
Copyright © 2013 Gradus Group
|