BLACK DECKER LEDUC9 1WB User Manual

POWERING ON/OFF  
Using the Power Button: Press the power button located on the light bar once to turn the lights on. To  
turn off, press the power button again. (See FIG. 1)  
Using the Motion Sensor: Ensure that your hand is within at least 2” of the motion sensor on the  
mounted control box. Wave your hand in any direction underneath the control box to turn the power on  
and/or off. (See FIG. 2)  
FIG. 1  
FIG. 2  
FIG. 3  
USING THE DIMMER  
There are ten (10) preset lighting levels that can be adjusted with the dimmer button. To select your  
lighting level, ensure that the system is already powered on. Hold down the button to change the  
lighting level and/or switch between the presets. (See FIG. 1)  
NOTE: This lighting system has a memory function that will use the last selected brightness level the  
next time it is powered on.  
USING THE TIMER  
This lighting system is equipped with an optional auto shutoff timer switch that will power the unit off  
after three (3) hours. To activate, switch to the “on” position. To disable, switch to the “off” position.  
(See FIG. 3)  
PUSH CONNECT INSTALLATION  
The wire can be cut to custom lengths and is used to connect the light bar(s) to the control box and  
link light bars together.  
Inside of the wire are two (2) white wires and one (1) gray wire (See FIG. 4); To expose the solid  
copper wire, cut approximately 3/8” on each of the three wires.  
After exposing the solid copper wires, connect to the control box or light bar (depending on where  
you are in the installation process)  
To connect to the control box or light bar, simply push the copper wires into the connection on the  
control box or light bar. (See FIG. 5)  
NOTE: The gray wire must always link to the middle connection, while the white wires can  
connect to either of the outer connections.  
If connected properly, the wire should hold securely and not disengage.  
NOTE: If you need to release a wire from a light bar, remove the end cap to expose the connection  
(see FIG. 6) and use the included tool to press and release the copper wires from the light.  
FIG. 4  
FIG. 5  
FIG. 6  
APPLICATION OPTIONS  
Tool-Free  
1. Wipe down the mounting surface with a clean, lint-free cloth.  
2. Peel red backing from the adhesive.  
3. With the adhesive side facing the mounting surface, place the piece ꢀrmly on its desired location  
and hold for 5 seconds.  
Screw-In  
1. Follow the Tool-Free application steps.  
2. Remove light bars from bar mounting clips to expose the screw holes. (See FIG. 7)  
NOTE: Skip this step for wire clips as the screw hole is already exposed.  
3. Drill 7/32” pilot holes through each exposed screw hole. (See FIG. 8)  
4. Secure each mounting clip using the provided mounting screws.  
FIG. 7  
CONFIGURATION OPTIONS  
Split Conꢀguration: For layouts where preferred power source is centrally located within  
cabinets/mounting surfaces. (See FIG. 9)  
Continuous Conꢀguration: For layouts where preferred power source is on either side of  
7/32”  
7/32”  
cabinets/mounting surfaces. (See FIG. 10)  
FIG. 8  
INSTALLATION TIPS  
Optimal Illumination  
For cabinets up to 36” in length, one (1) light bar can be used. For cabinets over 36” in  
length, two (2) light bars should be used.  
Light Bar Placement  
Use the spacer provided in your kit to help measure and guide the placement of each light  
bar.  
FIG. 9  
Hiding Jumper Wires  
Use the included wire clips to hide all loose and hanging wires: To mount the wire clips, use  
the Tool-Free or Screw-In application process.  
Running Wires Through Cabinets  
Jumper Wire: To feed the light bar jumper wire through a cabinet, use a 7/32” drill bit (not  
included).  
FIG. 10  
Power Adapter Wire: To feed the power adapter wire through a cabinet, use a 3/8” drill bit  
(not included).  
Control Box Wire: To feed the control box wire through a cabinet, use a 1/2” drill bit (not  
included).  
STEP-BY-STEP INSTALLATION  
For additional information, please visit PureOpticsLED.com  
It is important and necessary to follow all local and national electrical codes. If you are unsure of your  
local codes, please contact your local town or city electrical inspector.  
1. Consider layout and conꢀguration  
Determine how many lights you’ll need to install - each light bar is designed to effectively illuminate  
cabinets 12”-36”.  
FIG. 11  
FIG. 12  
NOTE: Keep in mind that each power supply option has a maximum amount of light bars it can  
power.  
Determine the location of your control box with hands-free power control; An ideal location is on the  
underside of a cabinet in an easily accessible location.  
Determine the location of your power supply (plug-in or direct wire options) and take note of the  
length of your power cord, which will connect to the control box.  
NOTE: There are several installation methods that can allow for ꢁexible placement of your  
hands-free on/off control box that are illustrated under CONFIGURATION OPTIONS.  
2. Install the control box  
After determining its desired location, follow the Tool-Free application steps (see FIG. 11). Before  
mounting, be sure to leave room for the jumper wires, which will connect on one or both sides of the  
control box (depending on your conꢀguration).  
FIG. 13  
FIG. 14  
FIG. 15  
FIG. 16  
FIG. 17  
Using a 3/8” drill bit, drill holes as needed to connect your control box to the power supply (See  
FIG. 12)  
PRO TIP: If connecting the control box to the power supply inside of a cabinet, use a 1/2” drill bit to  
feed the control box wire into the cabinet.  
3. Install the light bars  
Slide two (2) bar mounting clips on to each light bar.  
Using your installation spacer as a guide, mount light bars using Tool-Free or Screw-In application  
process. (See FIG. 13)  
4. Connect the control box to the nearest light bar  
Cut the desired length of wire needed to connect the control box to the nearest light bar.  
Cut and strip the wire to expose approximately 3/8” of the solid copper wire on each of the three  
wires.  
Push the solid copper wires into their respective connections on the control box.  
NOTE: The gray wire must always link to the middle connection, while the white wires can connect  
to either of the outer connections. (See FIG. 14)  
5. Connect the light bars together  
Repeat the process outlined in step 4 to connect two light bars together. (See FIG. 15)  
To hide the jumper wires, route them through the frames of each cabinet by using a 7/32” bit to drill  
holes as close to the front of the frame as possible. (See FIG. 16)  
6. Hide excess wires  
Use the included wire clips to hide all loose and hanging wires (see FIG. 17); To mount the wire  
clips, use the Tool-Free or Screw-In application process.  
THREE-YEAR LIMITED WARRANTY  
Amax Inc. warrants to the original retail purchaser that the product purchased is free from defects in material and workmanship, and agrees to  
repair or replace, at Amax’s option, any defective BLACK+DECKER™ branded under cabinet lighting product (3) years from the date of  
purchase. Warranty is not transferable. Proof of purchase date required. This warranty covers only damage resulting from defects in material  
or workmanship; it does not cover conditions or malfunctions resulting from normal wear, neglect, abuse, accident, or repairs attempted or  
made by other than our national repair center or authorized warranty service centers. You are responsible for the costs of shipping the  
defective product to Amax Inc.  
THIS WARRANTY IS THE EXCLUSIVE WARRANTY OF AMAX INC., AND IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES INCLUDING, BUT  
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURCHASE. AMAX INC. SHALL NOT BE  
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.  
Some states and countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or  
exclusions may not apply to you. This warranty gives you speciꢀc legal rights, and you may also have other rights which vary from state to  
state and country to country. For information on our warranty claim procedure, please contact us at 855-784-4322.  
Latin America: This warranty does not apply to products sold in Latin America. For products sold in Latin America, check country speciꢀc  
warranty information contained in the packaging, call the local company, or see the website for warranty information.  
PureOpticsLED.com  
U
C L  
US  
1-855-784-4322  
LISTED  
BLACK+DECKER and the BLACK+DECKER  
Logo are trademarks of The Black & Decker  
Corporation and are used under license. All rights  
reserved. Product in this box may differ slightly  
from that pictured. Not all accessories shown in  
photography are included in this package.  
E474857  
En México Importado por: Black & Decker  
S.A. de C.V. Avenida Antonio Dovali Jaime #  
70 Torre B Piso 9 Colonia La Fe, Santa Fé,  
Delegación Alvaro Obregón, México D.F.  
01210 • R.F.C.: BDE810626-1W7  
Manufactured by:  
Amax Incorporated East Greenwich, RI 02818  
Under license from The Black and Decker  
Corporation USA and Canada Only  
A01343  
Copyright © 2018 Amax Incorporated  

Xerox Workcentre 480cx User Manual
Whirlpool Acu088pr0 User Manual
Toshiba Multifunctional Digital Systems 282 User Manual
Soleus Air Kc 32u User Manual
Panasonic Cw806tu User Manual
NEC NP610S User Manual
LG 65UH615A 02 User Manual
EMERSON MW8111SS User Manual
BROTHER HL 6180DWT User Manual
BLACK DECKER PHS550G User Manual