(Original instructions)
ENGLISH
FIG. F
FIG. G
13
FIG. H
FIG. I
15
14
18
17
16
FIG. J
3
(Original instructions)
ENGLISH
There is an increased risk of electric
shock if your body is earthed or
grounded.
Intended use
TM
Your BLACK+DECKER JS10 and JS20
jigsaw has been designed for sawing wood,
plastics and sheet metal. This tool is
intended for consumer use only.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
GENERAL SAFETY RULES
d. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
Warning! Read and understand all
instructions. Failure to follow all instructions
listed below, may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
SAFETY INSTRUCTIONS
e. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
General power tool safety warnings.
Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings and
instructions listed below may result in
electric shock, fire and/or serious injury.
f. If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
Save all warnings and instructions for
future reference. The term “power tool” in
all of the warnings listed below refers to
your mains operated (corded) power tool or
battery operated (cordless) power tool.
3. Personal Safety
a. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool
while you are tired or under the
influence of drugs, alcohol or
1. Work Area Safety
a. Keep work area clean and well lit.
medication. A moment of inattention
while operating power tools may result in
serious personal injury.
Cluttered and dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
b. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
c. Keep children and bystanders away
while operating a power tool.
Distractions can cause you to lose
control.
c. Prevent unintentional starting. Ensure
the switch is in the oꢀ-position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your
finger on the switch or energising power
tools that have the switch on invites
accidents.
2. Electrical Safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce
risk of electric shock.
d. Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a
rotating part of the power tool may result
in personal injury.
b. Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
4
(Original instructions)
ENGLISH
e. Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool
bits etc., in accordance with these
f. Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations diꢀerent from those intended
could result in a hazardous situation.
g. If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
these devices can reduce dust related
hazards.
5. Service
a. Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
4. Power Tool Use and Care
ADDITIONAL SAFETY
a. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
WARNINGSFOR JIGSAWS AND
RECIPROCATING SAWS
a. Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may
make exposed metal parts of the power
tool “live” and could give the operator an
electric shock.
b. Do not use the power tool if the switch
does not turn it on and oꢀ. Any power
tool that cannot be controlled with the
switch is dangerous and must be
repaired.
c. Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any
b. Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by
hand or against your body leaves it
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
unstable and may lead to loss of control.
c. Keep hands away from cutting area.
Never reach underneath the work piece
any reason. Do not insert fingers or
thumb into the vicinity of the
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
reciprocating blade and blade clamp. Do
not stabilize the saw by gripping the
shoe.
d. Keep blades sharp. Dull or damaged
blades may cause the saw to swerve or
stall under pressure. Always use the
appropriate type of saw blade for the
workpiece material and type of cut.
e. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may aꢀect the power
tools operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly
e. When cutting pipe or conduit, make sure
that they are free from water, electrical
wiring, etc.
maintained power tools.
f. Do not touch the workpiece or the blade
immediately after operating the tool.
They can become very hot.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
5
(Original instructions)
ENGLISH
g. Be aware of hidden hazards, before
cutting into walls, floors or ceilings,
check for the location of wiring and
pipes.
List of Contents
1
1
Jigsaw
Hex key
h. The blade will continue to move after
releasing the switch. Always switch the
tool oꢀ and wait for the saw blade to
come to a complete standstill before
putting the tool down.
Position of date barcode
The Date Code, which also includes the year
of manufacture, is printed into the housing.
Example:
Warning! Contact with, or inhalation
of dusts arising from cutting
applications may endanger the
2017 XX JN
Year of manufacturing
health of the operator and possible
bystanders. Wear a dust mask specifically
designed for protection against dust and
fumes and ensure that persons within or
entering the work area are also protected.
Safety of others
•
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
i. The intended use is described in this
instruction manual. The use of any
accessory or attachment or performance
of any operation with this tool other than
those recommended in this instruction
manual may present a isk of personal
injury and/or damage to property.
Electrical safety
•
Children should be supervised to ensure
that they do not play with the appliance.
Your tool is double insulated;
therefore no earth wire is required.
Always check that the main voltage
corresponds to the voltage on the
rating plate.
Residual risks
Additional residual risks may arise when
using the tool which may not be included in
the enclosed safety warnings. These risks
can arise from misuse, prolonged use etc.
Even with the application of the relevant
safety regulations and the implementation of
safety devices, certain residual risks can not
be avoided. These include:
Warning! If the power cord is
damaged, it must be replaced by
the manufacturer, authorized
BLACK+DECKER Service Center or
an equally qualified person in order
to avoid damage or injury. If the
power cord is replaced by an equally
qualified person, but not authorized
by BLACK+DECKER, the warranty
will not be valid.
•
•
•
Injuries caused by touching any
rotating/moving parts.
Labels on tool
The label on your tool may include the
following symbols:
Injuries caused when changing any parts,
blades or accessories.
Injuries caused by prolonged use of a
tool. When using any tool for prolonged
periods ensure you take regular breaks.
Hz ....... Hertz
W ........ Watts
min ..... minutes
Read
Instructions
Manual
...... Class II
Construction
....
....
Earthing
Terminal
Use Eye
•
•
Impairment of hearing.
Protection
..... Alternating
Safety Alert
Symbol
Current
Use Ear
Health hazards caused by breathing dust
developed when using your tool
(example: working with wood, especially
oak, beech and MDF.)
Protection
..... Direct
.../min..
Revolutions
or Recipro-
cation per
minute
Current
V ........ Volts
n0 ....... No-Load
Speed
A ........ Amperes
6
(Original instructions)
ENGLISH
3. Loosen both blade clamp screws (9) and
insert the saw blade (11) as far as possible
into the slot in the blade clamp.
FEATURES (Fig. A)
1. Trigger switch
2. Lock-On button
3. Motor vents
Notes:
a) Ensure the blade is nested in the groove
in the support roller (8).
4. 3 mm Hex key
5. Hex key holder
6. Dust port
b) The holes in universal fitting saw blades
are not designed for alignment with the
screw holes in the blade clamp.
4. Tighten both blade clamp screws (9)
securely against the blade.
7. Tilting sole plate
8. Blade roller
To remove the jigsaw blade:
1. Unplug your jigsaw.
9. Blade screws
10. Chip guard
2. Loosen blade clamp screws (9) using the
slotted screwdriver.
ASSEMBLY & OPERATION
3. Remove the blade.
Warning! Before attempting any of
the following operations, make sure
that the tool is switched oꢀ and
On/Oꢀ trigger switch (Fig. C)
unplugged and that the saw blade has
stopped. Used saw blades may be hot.
To turn your jigsaw ON, depress the trigger
switch (1). To turn the saw OFF, release the
trigger switch.
Warning! Always disconnect your
jigsaw from the power source when
replacing blades, tilting the sole
Lock-on button (Fig. D)
plate, cleaning or when the tool is not in
use. Disconnecting the jigsaw will prevent
accidental starting that could cause serious
personal injury.
Your jigsaw is equipped with a lock-on
feature, which is convenient when
continuous cutting for extended periods of
time is required. To lock the switch ON,
depress the trigger switch (1), push in and
hold the lock-on button (2), then release the
trigger. Release the lock-on button and your
jigsaw will continue running. Depress and
release the trigger switch to release lock.
Blade options
Your jigsaw is designed to permit the use of
many diꢀerent saw tooth configurations.
Installing blades (not included)
Note: The lock-on button can be accessed
from left side of the handle.
1. Unplug your jigsaw from the power
source.
Variable speed control (Fig. E)
(only JS20)
Warning! Failure to unplug your jigsaw from
the power source could result in accidental
starting causing serious injury.
Set the jigsaw speed by rotating the variable
speed control wheel (12) to the appropriate
speed. Rotating the variable speed control
wheel toward the rear of the jigsaw will
result in slower speeds. Position the speed
control dial at “1” for the slowest speed, “3”
for medium speed and at “6” for the highest
speed.
2. Insert the slotted screwdriver through
the access hole in the chip shield (10).
Note: Use the slotted screwdriver (not
supplied) to loosen screws.
7
(Original instructions)
ENGLISH
of the motor housing (18) with the
desired angle mark (17) on the side of the
base, then slide the sole plate forward to
engage the notches (16) into the motor
housing pin.
Note: Angle marks on the sides of the
jigsaw base are for reference only.
Operator should use a protractor to verify
angles.
Vacuum port switch (Fig. F)
During normal use without the vacuum
connected, the vacuum port switch (13)
must be slid toward the rear of the tool .
This will allow the internal motor fan to
continuously blow the sawdust away from
the cutting mark. When the vacuum is
connected, the vacuum port switch must be
slid toward the front of the tool. This
positions the internal baꢀe to divert the
sawdust through the vacuum port so it can
be evacuated by the workshop vacuum.
4. Once the desired bevel angle is obtained,
lock the sole plate by tightening the sole
plate pivot screws.
5. Make a test cut in a scrap piece of
material and measure the bevel angle.
Adjust bevel angle if necessary.
OPERATION
Warning! Never use the tool when the saw
shoe plate is loose or removed.
HINTS FOR OPTIMUM USE
General cutting
Sawing laminates
Warning! Keep hands and fingers away
from the space between the motor housing
and the blade clamp. Do not reach
underneath workpiece while the saw is
running.
When cutting laminates, splintering may
occur which can damage the presentation
surface. The most common saw blades cut
on the upward stroke, therefore if the shoe
plate is sitting on the presentation surface
either use a saw blade that cuts on the
downward stroke or:
Rest the front of the sole plate on the
workpiece and align the cutting edge of the
blade with the cutting line on your
workpiece (Fig. G). Make sure the power
cord is out of your way and not in the path
the blade will follow. Start your saw and
move it toward the workpiece. Apply
enough downward pressure to keep the saw
steady and only enough forward pressure to
keep the blade cutting freely.
•
•
Use a fine-tooth saw blade.
Saw from the back surface of the
workpiece.
•
To minimise splintering, clamp a piece of
scrap wood or hardboard to both sides of
the workpiece and saw through this
sandwich.
Warning! Do not force the saw. Forcing the
saw may overheat the motor and break saw
blades.
Sawing metal
Warning! Do not use a vacuum when cutting
metal. Metal filings will be hot and may
cause fire. Be aware that sawing metal takes
much more time than sawing wood.
Bevel cutting
Bevel cutting angles may be adjusted from
zero to 45° either left or right. To adjust the
bevel angle:
•
Use a saw blade suitable for sawing
metal.
1. Loosen both sole plate pivot screws (14)
until the sole plate (15) can be rotated
(Fig. H).
•
When cutting thin sheet metal, clamp a
piece of scrap wood to the back surface
of the workpiece and cut through this
sandwich.
Note: Use the 3 mm hex key supplied.
2. Bevel angles (17) are marked on a scale
located on the side of the sole plate
(Fig. I).
•
Spread a film of oil along the intended
line of cut.
3. Slide the sole plate back. Align the edge
8
(Original instructions)
ENGLISH
When cutting conduit, pipe or angle iron,
clamp work in a vise if possible and saw
close to the vise. To cut thin sheet materials,
“sandwich” the material between hardboard
or plywood and clamp the layers to eliminate
material vibration and tearing. By doing this,
the material will be cut smoothly. Lay out
your pattern or cutting lines on top of the
“sandwich”.
Plunge cutting
Warning! To avoid loss of control, broken
blades or damage to the workpiece, always
use extreme caution when making plunge
cuts. It is not recommended to plunge cut
any material other than wood. Wherever
possible, drill a 3/8” (10 mm) or bigger pilot
hole in the area to be cut out and start
cutting with the blade in the pilot hole. This
will avoid the need to plunge cut.
MAINTENANCE
General
Note: Use only blades with 7 teeth per inch
for plunge cutting.
Warning! Do not at any time allow solvents
such as brake fluids, gasoline,
petroleum-based products, penetrating oils,
etc. to come in contact with plastic parts.
They contain chemicals that can damage,
weaken or destroy plastic. Use a clean dry
cloth to remove dirt, dust, oil, grease, etc.
1. To plunge cut an inside hole, clearly mark
the cutting line on the workpiece.
2. Set the bevel angle at 0° then lock the
sole plate.
3. Tilt the saw forward so it rests on the
front edge of the sole plate and in a
position so the blade will NOT touch the
workpiece when the switch is turned ON
(Fig. J).
Warning! Use safety goggles when using an
air jet to blow dust out of the jigsaw. Using
this jigsaw for cutting fiberglass, wallboard
or plaster will result in accelerated wear due
to the abrasive nature of these materials. It is
important that you clean the jigsaw
frequently when cutting these materials.
DO NOT abuse power tools. Abusive
practices can damage the tool as well as the
workpiece.
Note: Make sure the saw blade is inside
the area to be cut.
4. Start the saw and slowly lower the blade
onto the workpiece while making sure
the front of the sole plate remains in
contact with the workpiece. Allow the
blade to cut through the wood.
Warning! DO NOT attempt to modify this
jigsaw or create accessories not
recommended for this jigsaw. Any such
alteration or modification is misuse and
could result in a hazardous condition leading
to possible serious injury. It will also void the
warranty.
5. Continue lowering the blade into the
workpiece until the sole plate rests flat
on the workpiece. Continue sawing
toward the cutting line and complete the
cut as required.
Metal cutting
Your BLACK+DECKER tool has been
designed to operate over a long period of
time with a minimum of maintenance.
Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Many types of metal can be cut with your
jigsaw. When cutting any kind of material,
be careful not to twist or bend the blades.
Do not force the blade. If the blade chatters
or vibrates excessively, use a finer tooth
blade. If the blade heats excessively, reduce
speed of cutting. If the blade teeth become
clogged when cutting soft metals such as
aluminum, use a coarser blade with fewer
teeth per inch. Clamp all work firmly and
saw as close as possible to the clamping
point to eliminate any vibration of the work
being cut.
•
Regularly clean the ventilation slots in
your tool using a soft brush or dry cloth.
•
Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or
solvent-based cleaner. Never let any
liquid get inside the tool and never
immerse any part of the tool into liquid.
9
(Original instructions)
ENGLISH
Important! To assure product SAFETY and
RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this
manual) should be performed by authorized
service centers or other qualified service
personnel, always using identical
SERVICE INFORMATION
BLACK+DECKER oꢂers a full network of
company-owned and authorized service
locations. All BLACK+DECKER Service
Centers are staꢂed with trained personnel to
provide customers with eꢁcient and reliable
power tool service. For more information
about our authorized service centers and if
you need technical advice, repair, or genuine
factory replacement parts, contact the
BLACK+DECKER location nearest you, or
replacement parts.
LUBRICATION
All of the bearings in this jigsaw are
lubricated with a sufficient amount of high-
grade lubricant for the life of the unit under
normal conditions. Therefore, no further
lubrication is required.
NOTE
Protecting the environment
•
BLACK+DECKER’s policy is one of
continuous improvement to our products
and, as such, we reserve the right to
change product specifications without
prior notice.
Separate collection. This product
must not be disposed of with normal
household waste.
Should you find one day that your
BLACK+DECKER product needs replace-
ment, or if it is of no further use to you, do
not dispose of it with household waste.
Make this product available for separate
collection.
•
•
•
Standard equipment and accessories may
vary by country.
Product specifications may differ by
country.
Complete product range may not be
available in all countries. Contact your
local BLACK+DECKER dealers for range
availability.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Reuse of
recycled materials helps prevent environ-
mental pollution and reduces the demand
for raw materials.
SPECIFICATIONS
JS10
JS20
400W
Local regulations may provide for separate
collection of electrical products from the
household, at municipal waste sites or by
the retailer when you purchase a new
product.
Power
400W
Blade speed
3000/min
1000-3000/min
18 mm
Stroke length
18 mm
BLACK+DECKER provides a facility for the
collection and recycling of BLACK+DECKER
products once they have reached the end of
their working life. To take advantage of this
service please return your product to any
authorised repair agent who will collect
them on our behalf.
Cutting depth @ 90° 65 mm in wood 65 mm in wood
6 mm in steel
0–45°
6 mm in steel
0–45°
Sole plate tilt
You can check the location of your nearest
authorised repair agent by contacting your
local BLACK+DECKER oꢁce at the address
indicated in this manual. Alternatively, a list
of authorised BLACK+DECKER repair
agents and full details of our after-sales
service and contacts are available on the
10
(Original instructions)
ENGLISH
Warranty
BLACK+DECKER is confident of the quality
of its products and oꢂers an outstanding
guarantee. This guarantee statement is in
addition to and in no way prejudices your
statutory rights.
If a BLACK+DECKER product becomes
defective due to faulty materials,
workmanship or lack of conformity, within 6
months from the date of purchase,
BLACK+DECKER guarantees to replace
defective parts, repair products subjected to
fair wear and tear or replace such products
to make sure of the minimum inconvenience
to the customer unless:
•
•
•
The product has been used for trade,
professional or hire purposes.
The product has been subjected to
misuse or neglect.
The product has sustained damage
through foreign objects, substances or
accidents.
•
Repairs have been attempted by persons
other than authorised repair agents or
BLACK+DECKER service staꢂ.
To claim on the guarantee, you will need to
submit proof of purchase to the seller or an
authorised repair agent. You can check the
location of your nearest authorised repair
agent by contacting your local
BLACK+DECKER oꢁce at the address
indicated in this manual. Alternatively, a list
of authorised BLACK+DECKER repair agents
and full details of our aftersales service and
contacts are available on the Internet at:
11
Names & Addresses for BLACK + DECKER India Service Concessionaries
ANDHRA PRADESH: KAKINADA - LAKSHMI SIVARAM ENTERPRISES, #43-1-48, OPP: IDBI BANK, MAIN ROAD, KAKINADA.
BRANCH:SARPAVARAM JUNCTION, BESIDE POLICE STATION KAKINADA, ANDHRA PRADESH, 533001, Tel: 9848317859,
ROOM, NEAR SANTHI, MAIN, ROAD
RAJAHMUNDRY RAJAMUNDRY, 533101, Tel: 9966644555, Email:
[email protected]. TIRUPATI - MAHARAJA SPARES, NO. 42 NETHAJI ROAD TIRUPATI, 517501, Tel: 0877 2253426,
Email: "[email protected], [email protected]". VISAKHAPATTANAM - S B ENTERPRISES, 28-16-14 ,
SURYABAGH VISAKHAPATANAM, ANDHRA PRADESH, 530020, Tel: 0891-2562208 / 2569917, Email: [email protected].
VISAKHAPATTANAM - SRI GANESH HARDWARE & ELECTRICALS, NO. 7-16-73 OLD GAJUWAKA JN VISAKHAPATANAM,
MACHINE AND TOOLS, A.T.ROAD NEAR RUPSHREE CINEMA, TOKOBARI GUWAHATI, ASSAM, 781001, Tel: 2591868, Email:
[email protected]. GUWAHATI - BAGARIA TOOLS AND HARDWARE, NEAR HOTEL VISHWARATNA AT ROAD
GUWAHATI, ASSAM, 781001, Tel: 2511173, Email: [email protected]. GUWAHATI - VINAYAK TOOLS AND MACHINERY,
A-1, MANGAL RAM TOWER OPPOSITE POLICE RESERVE, A.T.ROAD GUWAHATI, ASSAM, 781001, Tel:
,
Email:
[email protected]. JORHAT - ASSAM MACHINE TOOLS, GAR-ALI, JORHAT GUWAHATI ASSAM, 785001, Tel: 2321607,
Email: [email protected]. TEZPUR - SHYAM MACHINERY AND TOOLS, A.C. PLAZA, N.B.ROAD (NEAR ANANTA
TRADERS, RAMNA ROAD, NEAR RAMA BHAVAN, P.S.-CIVIL LAIN, P.O.- GAYA , BIHAR, 823001, Tel: , Email: [email protected].
CHATTISGARH: RAIPUR - V. M. ENTERPRISES, MILLENNIUM PLAZA, FIRST FLOOR-31 BANSTAL G E ROAD RAIPUR,
492001, Tel: 0771-4280808, Email: [email protected]. DELHI/NCR: NOIDA - SHIVA MACHINERY TOOLS, C-100,
-
JMR
TECHSERV INDIA, M-7 1st FLOOR GURU RAM DASS BHAWAN COMMUNITY CENTRE RANJIT NAGAR NEW DELHI, 110041,
Tel: 011-45669290, Email: [email protected]. FARIDABAD - MAHALAKSHMI TRADING CORPORATION, Plot no 40/66B,
Industrial area, (near Raj gas agency) Near Hardware chowk, FARIDABAD, 121001, Tel: 0129-4023814, Email:
[email protected]. GURGAON - M/S SHRI GANPATI TRADERS, Plot NO:377/24,Model Town (4Marla) Near Gurudwara,
Gurgaon-122001 GURGAON, 122001, Tel: 0124 2320088, Email: [email protected]. GOA: PANJIM - MECH-TECH
ENGGINEERING SYSTEMS, G-2, EMERALD TOWERS, M.G. ROAD OPP STATE BANK ZONAL OFFICE, PANJI, GOA, 403001,
Tel: 0832-2223601, Email: [email protected]. PANJIM - S.K .TRADING, SHOP NO 4 ESTEEVE APARTMENT NEAR ALUA
HOTEL, MERCES PANJIM, 403005, Tel: , Email: [email protected]. VASCO-DA-GAMA - S.S.HITECH ENGINEERS, SHOP
NO-2, LAXJOT APPTS NEAR KTC BUS STAND
VASCO-DA GAMA, GOA, 403802, Tel: 0832-2515582, Email:
[email protected]. GUJARAT: AHMEDABAD - RUSHABH TRADERS, MIRA CHEMBER, OPP.SYNDICATE BANK KADIA KUI,
RELIEF ROAD AHMEDABAD, 380001, Tel: 079 22180265, Email: [email protected]. AHMEDABAD - SHIVAM SALES &
SERVICE, Shop No.7,G/F,Mira Mangal Appt.,Opp.Uday Tenamemnt,Times Of India Road,Satellite,Ahmedabad, 380051, Tel:
079-69501111, Email: [email protected]. AHMEDABAD - SHREE MARUTI TOOLS, B/5,NEW SHIVKRIPA APARTMENT
OPP, AGIYARAS MATA MANDIR, NAVA AHMEDABAD, GUJARAT, 380013, Tel: 079-7643580/7..., Email:
[email protected]. AHMEDABAD - SHYAM TRADING, 34, GREEN VILLA NR. H.B. KAPADIA SCHOOL, GURUKUL
ROAD, MEMNAGAR, AHMEDABAD, GUJARATH, 380052, Tel: 079 66522025, Email: [email protected]. ANKELESHWAR
- CHINTAN ELECTRICALS, PLOT NO-1006,GIDC ESTATE, ANKELESHWAR,DIST-BHARUCH ANKELESHWAR,DIST-BHARUCH,
393002, Tel: 02646-251524, Email: [email protected]. RAJKOT - JAY ENTERPRISE, Dhebar Road, Near Ashok Guest House,
RAJKOT, 360001, Tel: 0281 – 2236235, Email: [email protected]. SURAT - NATIONAL POWER TOOLS ( SURAT ),
HG41-42, RUSHABH TOWERS, Near Jain Temple, Adajan Patia Rander Road, Surat, 395009, Tel: 0261-2788227, Email:
[email protected]. SURAT
RESIDENCE,KAPODRA CROSSING, VARUCHA ROAD SURAT, 395006, Tel: , Email: [email protected]. SURAT - VIKRAM
ENGINEERS, M.G.ROAD NO-4 SANGHAVI HOUSE UDYOGNAGAR UDHANA, 394210, Tel: 0261-2274025, Email:
-
SOHAM REPARING CENTER, 11,RAMESHWAR SOCIETY, BESIDE RUDRAKSH
,
,
[email protected]. VADODARA - HARIOM ENTERPRISE, Laheripura New Road Opposite Sai Baba temple VADODARA,
GUJARAT, 390001, Tel: 0265-6543678, Email: [email protected]. VAPI - BRIGHT MACHINE TOOLS, A-1 Plot no 126,Opp
Hotel way wait bhadakmora silvasa road, vapi, 396195, Tel: 0260-2450808, Email: [email protected]. BARDOLI - VDN
ENTERPRISE PVT LTD, 201, 1ST FLOOR, M.G ROAD DARSHAN APARTMENT, BARDOLI, 394601, Tel: 0262 - 2226507, Email:
[email protected]. AHMEDABAD - GITANJALI TRADERS, LAXMI NAGAR CORNER OPP;GANGOTRI HOTEL, NH NO 8
NARODA,AHMEDABAD,GUJARAT, 382330, Tel: 079-22801346, Email: [email protected]. SILVASSA - INDIA TOOLS
CENTRE, NO.8,Silver Point, OPP: TO ICICI BANK, Silvassa - Vapi Main Road SILVASSA, 396230, Tel: 2602423518, Email:
[email protected]. AHMEDABAD - SHREE GANESH SALES &SERVICE, E/21, MIRA MANGAL APARTMENTS OPP:
UDAY,SOC TIMES OF INDIA ROAD,VEJALPUR
Email: [email protected].
,
SATELLITE, AHMEDABAD, 380051, Tel: 079
-
40320976,
HARYANA: BHIWADI - HARYANA AGENCIES, NEAR ALLAHABAD BANK NH-8 , DELHI-JAIPUR HIGHWAY, BANIPUR CHOWK
BAWAL(REWARI)HARYANA, 123501, Tel: 01493-226319, Email: [email protected]. HIMACHAL PRADESH: BADDI -
CHANDAN INDUSTRIES, B.O. OPP. 4 SEASON HOTEL, PINJORE ROAD, NEAR BUS STAND BADDI, HIMACHAL PRADESH,
-
BHAGWATI SALES
CORPORATION, MAIN ROAD, LAST MORTH GANDHI NAGAR JAMMU, 180001, Tel: 0191-2452718, Email:
,
[email protected] . DHANBAD - SIGMA ENTERPRISES, SARAIDHELA MAIN ROAD NEAR AJAY TALKIES DHANBAD,
EQUIPMENTS, S ‘ TYPE CHAWK , MAIN ROAD ADITYAPUR, JAMSHEDPUR WEST BENGAL, 831013, Tel: 0657-2383282, Email:
[email protected]. JAMSHEDPUR
-
MANGILALL RUNGTA, P.O.JUGSALAI JAMSHEDPUR,
JHARKHAND
JAMSHEDPUR, 831006, Tel: 0657-423738, Email: [email protected]. RANCHI - INDUSTRIAL TOOLS AGENCY, DR.
KARNATAKA: BANGALORE - HINDUSTAN TOOLS, Shop No.40/3, Dr. Ismail complex,S.P.Road, Bangalore, 560002, Tel:
080-41513796, Email: [email protected]. BANGALORE
-
MINI SALES AND TOOLS SERVICE, NO 12,1ST
FLOOR,R.K.BUILDING 1ST CROSS, N.R.ROAD BANGALORE, KARNATAKA, 560002, Tel: 26702375, Email:
[email protected]. BANGALORE - NEW BANGALORE POWER TOOLS, NO-637/4,FIRST FLOOR, MUNIYAPPA COMPLEX,
OPP.I.B.P.PETROL BUNK, JALAHALLI CROSS BANGALORE, KARNATAKA, 560057, Tel: 25900650, Email: [email protected].
BANGALORE
-
PATEL TRADING CORPORATION, 1ST FLOOR, NO. 57/3 SARDAR PATRAPPA ROAD BANGALORE,
KARNATAKA, 560026, Tel: 8026754572, Email: [email protected]. BANGALORE - VISHAL ENTERPRISES, I FLOOR, NO.5
MANDI VEERAPPA LANE S.J.P. ROAD CROSS BANGALORE, KARNATAKA, 560002, Tel: 080-40903826, Email:
[email protected]. BELGAUM - VIKRANT SALES CORPORATION, KHANAPUR ROAD UDYAMBAG BELGAUM, KARNATAKA,
590008, Tel: 0831-2441256, Email: [email protected]. BHATKAL - CITY TOOLS CENTER, ISMAIL COMPLEX, N H-17
-
SAGAR
ELECTRICALS, SHOP NO. 55 CMC COMPLEX BAGALKOT CROSS BIJAPUR, KARNATAKA, 586101, Tel: 08352-22637. HUBLI -
A B AGENCIES, RAZAK BUILDING, KOPPIKAR ROAD KOPPIKAR ROAD, HUBLI KARNATAKA, 580020, Tel: 0836-2366812,
Email: [email protected]. MANGALORE - LAKSHMI SALES CORPORATION, LAKSHMI TOWERS, MAIN ROAD,KULAI, ,
MANGLORE MANGALORE, 574196, Tel: 0824-2407836, Email: [email protected]. KERALA: CALICUT - TOOL TECH INC,
DOOR NO. 16/931 & 932B ARADHANA TOURIST HOME, KALLAI ROAD, CALICUT, 673002, Tel: 0495-4025065, Email:
[email protected]. KOCHI - POWERTOOL ENTERPRISES, 44/2133E, FREEDOM ROAD KALOOR KOCHI, KERALA,
682017, Tel: 0484-4047593, Email: [email protected]. KOCHI - TOOL WORLD, 44/2708C KARUKAPPILLY DESHABHIMANI
-
VINDIA
ENTERPRISES, 39/3686, RAVIPURAM ROAD ERNAKULAM, KOCHI, KERALA, 682016, Tel: 0484-2356924, Email:
STATION, UP HILL P.O MALLAPURAM, 676505, Tel: 0483-2730603, Email: [email protected]. THRISSUR - TOOL MEC,
XII/689/27, MARS COMPLEX POOTHOLE ROAD THRISSUR, KERALA, 680004, Tel: 0487-2389739, Email: [email protected].
TRIVANDRUM - VIZHINJAM POWER TOOLS, SARHAN BUILDING, ARYASALAI TRIVANDRUM, 695036, Tel: 0471-6050001,
Email: [email protected]. KOTHAMANGALAM - JAMSAS TRADELINKS PRIVATE LTD, IX/529 D,FORSQARE,
THRIKKARIYOOR, NELLIKUZHI ROAD, ERNAKULAM DISTRIC, KOTHAMANGALAM, 686692, Tel: 0485-2828520, Email:
PRADESH, 462001, Tel: 0755-2736173, Email: [email protected]. INDORE - PIONEER INTERNATIONAL, 223, SHASTRI
INDORE - RELIABLE POWER TOOLS, 12, JAWAHAR MARG,SHOP NO 9 ,1st FLOOR, SHALIMAR PLAZA, INDORE- MADHYA
PRADESH, 452007, Tel: 0731-2366352, Email: [email protected]. INDORE - BALAJI ENTERPRISES, 118, SIYAGANJ
MAIN ROAD, INDORE- MADHYA PRADESH, 452001, Tel: 0731-2549374, Email: [email protected]. AHMEDNAGAR -
DATTA ENTERPRISES, N-16, NIMBALAK ROAD MIDC INDUSTRIAL AREA AHMEDNAGAR, MAHARASHTRA, 414111, Tel:
0241-6611130 / 6611131, Email: [email protected]. MAHARASHTRA: AKOLA - R B MACHINERY, MALIPURA CHOWK AKOLA
MAHARASHTRA, 444001, Tel: 0724-2424354, Email: [email protected]. ANDHERI (E) MUMBAI - UNIQUE AGENCIES,
MAROL MAROSHI ROAD, , MAROL, MUMBAI
AURANGABAD - ANIKET ENTERPRISES, X-324, NEAR HDFC BANK MAHARANA PRATAP CHOWK, BALAJI NAGAR MIDC,
AURANGABAD, 431005, Tel: 0240-2563312, Email: [email protected]. AURANGABAD - PADMAVATI ELECTRICALS,
OPP. RAMANAND COLONY KRANTI CHOWK AURANGABAD, 431005, Tel: 0240
-
2323033, Email:
[email protected]. AURANGABAD - SHACO SALES & SERVICES-AURANGABAD, Shop No. 9 , Awargaonkar
Complex , Below Hotel Ramgiri Jalna Road , Cidco , Aurangabad, 431005, Tel: 0240-6542111, Email: [email protected].
BOISAR - YASH VINAYAK ELECTRICAL, shop no 17, F-1 , Stayam Apt. Near- Ostwal English Academy School, Ostwal Empire
CHAKAN - SADAGURU POWER TOOLS AND ELECTRICAL, KOHINOOR CENTRE SHIVAJI CHOWK CHAKAN, PUNE, 410501,
Tel: 02135-645361, Email: [email protected]. DHULE - MISTRY ENTERPRISES, NEAR PRAKASH TALKIES PAROLA
SAPANA ENTERPRISES, 23/151, PANCHGANGA FACTORY TO SHAHPUR ROAD, NEAR KOTHARI SIZING, P O - GANGAN
ICHALKARANJI, MAHARASHTRA, 416116, Tel: 0230-2440592, Email: [email protected]. JALANA - S.P. SHAH &
SONS, MUTTA BUILDING NEAR NATRAJ CINEMA JALANA, MAHARASHTRA, 431203, Tel: -, Email:
-
SHRI GAJANAN
ELECTRICALS & MACHINER, 327-A , MAIN GATE , BASEMENT NEW B.J.MARKET, JALGAON MAHARASHTRA, 425001, Tel:
0257-222 4198, Email: [email protected]. KHAR (W) MUMBAI - MAHAVIR ELECTRICALS, Shop No 8, Inside B.M.C
-
SUSHITO
ENTERPRISES, B,UNDER GROUND - 1 PRABHAKAR PLAZA, STATION ROAD KOLHAPUR, MAHARASTRA, 416001, Tel:
0231-2667433, Email: [email protected]. KOLHAPUR - YASH ENTERPRISES, 1446 B/C, EMPIRE TOWER, SHOP
NO.16-B DASARA CHOWK, LAXMIPURI KOLHAPUR, MAHARASTRA, 416002, Tel: 0231-2644811, Email:
[email protected]. LATUR
MAHARASTRA, 413512, Tel: 02382-252127, Email: [email protected]. LONAVALA - SUPER AGENCIES, G’ WARD , SHOP NO
GURUNANAK CO-OPP HSG SOCIETY LONAWALA, MAHARASHTRA, 410401, Tel: 02114-273279, Email:
-
S
D
TRADERS, JAMDADE BUILDING BEHIND OLD POWER HOUSE LATUR,
-
6
[email protected]. MUMBAI - MANOHER ELECTRIC STORES, 10,Roshni Building,S.V.Road Oshiwara,Jogeshwari(West)
TOOLS, II ND FLOOR 71/73, NAGDEVI STREET MUMBAI, MAHARASTRA, 400003, Tel: 022-65213643/2035, Email:
[email protected]. MUMBAI - S. A. TRADERS, 76 , NAGDEVI CROSS LANE , SHOP NO 3. MUMBAI, MAHARASTRA, 400003,
Tel: 022 - 23400988, Email: [email protected]. MUMBAI - SHREE SIDHIVINYAK MACHINE TOOLS, Shop No 1 ,Vishwa
Mohini Building Opp Kamla Nehru Shoping Centre N.S Road , Mulund, 400080, Tel: 022-25612255, Email: [email protected].
NAGPUR - RATHI ENGINEERING COMPANY, 31 A, RADKE LAYOUT OPP- SAINT XAVIERS HIGH SCHOOL NAGPUR,
-
UNION HARDWARE STORES,
CENTRAL AVENUE DARODKAR CHOWK, NEAR ITWARI HIGH SCHOOL NAGPUR, 440002, Tel: 2769620, 2777729, Email:
[email protected]. NASIK - ESSEL ENGINEERS, NO. 6/7, KHETWANI D NEAR DONDE BRIDGE, UNTWADI, CIDCO
NASHIK, MAHARASHTRA, 422009, Tel: -, Email: [email protected]. NASIK - MESON TRADERS, NO. 994, MAIN ROAD
NASHIK NASHIK (M.S.), 422001, Tel: 0253 2507862, Email: [email protected]. NASIK - VIDAD ENGINEERING &
ELECTRICALS, MAHADEV NAGAR CORNER NEAR SATPUR BUS STOP, SATPUR - TRIMBAK ROAD SATPUR NASIK, 422007,
Tel: 0253 2363567, Email: [email protected]. NAVI MUMBAI - FINE ELECTRICAL WORKS, SHOP NO -3 ,JANTA MARKET
PLOT NO 3 & 4 ,SEC-23 , NR SADGURU HOTEL,TURBHE ,NAVI MUMBAI NAVI MUMBAI, 400705, Tel: 022-27839587, Email:
TURBHE SERVICE INDUSTRIES, NEAR JANTA MARKET VASHI, NAVI MUMBAI, 400705, Tel: 022-67973977 / 27835529, Email:
[email protected]. OSMANABAD
-
SHREE AMBICA MACHINE TOOLS, SHOP NO 26 SHIVAJI CHOWK OSMANABAD,
MAHARASHTRA, 413501, Tel: 0242-227281, Email: [email protected]. PUNE - EVEREST ENTERPRISES, SUKHWANI
NEST SHOP NO. 7, VIDHYAM NAGAR PIMPRI, PUNE, 411018, Tel: 27433522, Email: [email protected]. PUNE - FAITH
MACHINERY STORES, TIP TOP BLDG , SHOP NO-6&7 , 550B , NANAPETH , NEAR CHACHA HALWAI CHOWK , LAXMI ROAD ,
PUNE., 411002, Tel: 020-26137868 / 27433169, Email: [email protected]. PUNE - K Z TRADING CO, Shop no 2 ,
CORPORATION, NO. 95, GANESH PETH, LAXMI ROAD DULYA MARUTI CHOWK PUNE, 411002, Tel: 020-26344945 / 26344946 /
26341647, Email: [email protected]. PUNE - RAM ELECTRICALS, SHAGUN CHOWK PIMPRI PUNE, 411017. PUNE -
SOLANKI ENTERPRISES, NO. 288/B, RASTA PETH OPP M.S.E.B NEAR SAI MOTORS, PUNE, 411011, Tel: 020 26120268, Email:
Tel: 020-30681560, Email: [email protected]. PUNE - TECHNO TOOLS, 1 & 2, P.J. CHAMBERS NEAR AMBEDKAR
STATUE PIMPRI, PUNE, 411018, Tel: 020 30683334/5/6/7/8, Email: [email protected]/[email protected]. PUNE -
TOOL MAX, “MAULI” 738, BUDHWAR PETH GANESH ROAD, NR. PHADKE HOUD PUNE, 411002, Tel: 020 64007995, Email:
[email protected]. SANGLI - ARC POWER TOOLS & EQUIPMENTS, Atharv Sankul , Basement , Near Hotel New Ratna , Kupwad
Phata , Vishrambag , Sangli, 416436, Tel: 0233-2670443, Email: [email protected] / [email protected].
SANGLI
-
SHREE SALES AND SERVICES, PLOT NO. P-90 CHAKAN OIL MILL ROAD, M.I.D.C
.
SANGLI, 416436,
SATARA - M P ENGINEERS, SHOP NO -7 , JIWHALA HOUSING SOCIETY NEAR BOMBAY RESTAURANT, OLD M.I.D.C SATARA,
415001, Tel: 02162 - 247341, Email: [email protected]. SATARA - NEW MAHARASHTRA TRADERS, NO. 184 B1/C,
RAVIWAR
PETH
POWAI
NAKA
SATARA,
MAHARASHTRA,
415002,
Tel:
02162-235605,
Email:
[email protected]. SOLAPUR - MADAN .J. DALVI, GALA NO -7 .L.V.COMPLEX RAMLAL CHOWK, RAILWAY
LINE SOLAPUR, MAHARASTRA, 413001, Tel: 0217-2727051, Email: [email protected] . SOLAPUR - SIDDHRATNA SALES &
SERVICES, NO. 64 JODBHAVI PETH SOLAPUR, 413002, Tel: 0217 2729911, Email: [email protected]. SOLAPUR -
SUNEEL TEXTILE ENGINEERING INDUSTRI, PLOT NO. 65, NAGANE NAGAR BEHIND MAHAVIR TEA
COMPANY,KONDH-413004 KONDH, SOLAPUR, 413007, Tel: 0217-2622500, Email: [email protected] .THANE - SUPER
SALES & SERVICES, MONALISA BLDG., SHOP NO.5, HARINIWAS CIRCLE, , THANE, 400602, Tel: 022 - 25386845, Email:
.
PUNE - ABRA SALES, T-96/1 BHOSARI PIMPRI ROAD, M.I.D.C BHOSARI, PUNE
,
MAHARASHTRA, 411026, Tel: 020-66300599, Email: [email protected]. MUMBAI - UNIQUE ENGINEERS, OFFICE NO.3,183
BHUBANESWAR
ENTERPRISES, NO. 41 TARINGINI MARKET ROURKELA ORISSA, 769004, Tel: 0661-440 1443, Email:
[email protected] - M/S ADITYA TRADE &CO, APARNA NAGAR, PO CHAULIAGANJ, NEAR SITADEVI
-
UTKAL POWER TOOLS &SALES, SHOP NO 121,ANAND PLAZA LAKSHMI SAGAR SQUARE
-
SUBHAM
,
-
TRADERS-ORISSA, Bhadrakvati Road, Sanjay Cafe Building ,Cuttuck, Email: [email protected].
BHUBANESWAR - SUPREME TOOLS CENTRE,CUTTACK ROAD, KALPANA AREA,APEX MARKET COMPLEX, 751006, Tel:
GARDEN ROAD NEAR AJIT PRESS JALANDHAR, 144001, Tel: 0181-5030304, Email: [email protected]. LUDHIANA -
ARNEJA MACHINERY STORE, GILL ROAD LUDHIANA PUNJAB, 141003, Tel: 0161-2537923, Email: [email protected].
PANCHKULA - VIKAS WELD, PLOT NO-257 ,INDUSTRIAL AREA, PHASE- I , PANCHKULA HARYANA, 134113, Tel: 0172-2576437,
PHAGWARA, 144401, Tel: 01824 269082, Email: [email protected]. CHANDIGARH - J.V. MILL AND HARDWARE STORES,
418-A , INDUSTRIAL AREA PHASE II RAM DARBAR , CHANDIGARH, 160002, Tel: 0172-2640658, Email: [email protected].
RAJASTHAN: AJMER - S. S. AUTO AGENCIES, 4, KHAILAND MARKET, AJMER AJMER, 305001, Tel: 1452424120, Email:
[email protected]. ALWAR - HARYANA IRON TRADERS, RAM GANJ, ALWAR ALWAR, 301001, Tel: 0144-2700205, Email:
[email protected]. JAIPUR - ATUL ENTERPRISES, NEAR SIKAR HOTEL HANS MARG, S.C.ROAD JAIPUR,
-
BHATI HARDWARE HOUSE,
OPP-HANWANT SCHOOL PAL ROAD, JODHPUR (RAJ) JODHPUR-342003, 342003, Tel: 0291-2770506 / 0291-2770337, Email:
ROAD VILLAGE PAL JODHPUR, 342001, Tel: 0823-3994001, Email: [email protected]. JODHPUR - USHA TRADING
JAGDAMBA ENTERPRISES, NEAR THANDI PAU KI THADI, Agra Road, Sikandra Chouraya SIKANDARA, 303303, Tel: , Email:
CHENNAI POWER TOOLS AND ELECTRICALS, NO-648 , 1st Floor, MTH Road MANNURPET PADI CHENNAI, 600050, Tel:
044-26251663, Email: [email protected]. CHENNAI - K.S.ENGINEERING EQUIPMENTS, 16, TRUNK ROAD,
TOOLS AGENCIES, Old.No.11, New.No.21, Errabalu Street, Chennai CHENNAI, 600001, Tel: 044 - 25212150,044 - 25212160”:
[email protected],[email protected]. CHENNAI - PROFESSIONAL POWER TOOLS SALES &SERVICE, NO
77/155, BROADWAY CHENNAI CHENNAI, 600108, Tel: 044-64555872, Email: [email protected]. CHENNAI - SHRIMMA POWER
TOOLS, NO. 13, OLD MAHABALIPURAM ROAD KANDANCHAVADI, CHENNAI. CHENNAI, TAMIL NADU, 600096, Tel:
044-64534203, Email: [email protected]. CHENNAI - SRI KATHYAYENI ENTERPRISES, H-24, CENTRAL AVENUE
COIMBATORE - AARDWOLF ENGINEERING CO., NO. 180 A/9, DR. NANJAPPA ROAD NSP COMPLEX, COIMBATORE
COIMBATORE, TAMIL NADU, 641018, Tel: 0422 - 2301884 / 2380974, Email: [email protected]. COIMBATORE - ORIENT
EQUIPMENT & SERVICES, P.B. NO. 3795, SHOP NO G-5, V. R. ARCADE 295, DR. NANJAPPA ROAD COIMBATORE, TAMIL
NADU, 641018, Tel: 0422 - 2236432 /2238507, Email: [email protected],[email protected],[email protected].
HOSUR - BANU TOOLS, PLOT NO 7 , AMARAVATHI TOWERS VASAVI STREET,NEAR KVB BANK , NH 7, BYE PASS ROAD,
MADURAI - SANKER SALES CORPORATION, NO. 270, WEST MASI STREET MADURAI TAMIL NADU, 625001, Tel: 0452 -
2341803, Email: [email protected] - SRI ANDAL POWER TOOLS, NO. 5, A BLOCK SREE COMPLEX,
47/10E DEVANGAPURAM EXTN ST SHEVAPET, SALEM, 636002, Tel: 0427 2223718, Email: [email protected]. Madurai
-
SRI CHELLAM TOOLS, 166C NORTH VELI STREET Madurai Madurai, 625001, Tel: 04524-4504200, Email:
[email protected]. Chennai - THOMAS ENTERPRISES, 1/23, Kamatchi Nagar, vanagaram, Chennai, 600095, Tel:
044-24767133, Email: [email protected]. TUTICORN - BLESSON TRADERS, NO.15, DEVARPURAM ROAD,
TUTICORN, 628003, Tel: , Email: [email protected]. TELANGANA: ANANTHPUR - GENERAL ENGINEERING, # 18-246
,ROOM NO - 2 PINNI COMPLEX OPP KRISHNA THEATRE, ANANTHPUR, ANDHRA PRADESH, 515001, Tel: 0854-235706, Email:
[email protected]. HYDERABAD - GAYATHRI INDUSTRIAL CORPORATION, 10C, USHODAYA TOWERS, INDUSTRIAL
ROAD, SHAPURNAGAR,JEEDINEMTLA. HYDERABAD, ANDRA PRADESH, 500055, Tel: 040 65964671, Email:
[email protected]. HYDERABAD - ORIENTAL ENGINEERING CORPORATION, 5-2-990 NIZAM SHAHI ROAD
HYDERABAD, ANDRA PRADESH, 500095, Tel: 040 460 0056, 460 5319, Email: [email protected]. HYDERABAD -
S.V.INDUSTRIAL & MARKETING SERVICES, 2-3-64/8, S.NO-1 & 2 ,SAI POORNIMA OPP-AMBERPET NEW POLICE STATION, ,
HYDERABAD, ANDRA PRADESH, 500013, Tel: 040-27424828, Email: [email protected]. HYDERABAD - SRINIVASA
ENTERPRISES, 5-5-80,2ND FLOOR, SRI SRINIVASA COMMERCIAL COMPLEX , BESIDE RAO’S HOTEL RANIGUNJ,SECUNDE
VRINDAVAN ENTERPRISES, SHOP NO - 113,MEGHANA COMPLEX, OPP- ANDHRA BANK , BALANAGAR HYDERABAD,
12-6-15, HART STREET, TARAPET, VIJAYAWADA VIJAYWADA VIJAYWADA, 520001, Tel: 9848156713, Email:
COMPLE, LALATEMPLE SREET,RANIGUNJ,SECUNDERABAD, 500003.UTTARAKHAND: RUDRAPUR - PARVESH MARKETING,
DEHRADUN - M P ABRASIVES, SHOP NO- 19, SRI LAXMI PLAZA, GANDHI ROAD, DEHRADUN-UTTRAKHAND, 248001, Tel:
0135-2623192, Email: [email protected]. GHAZIABAD - SHARMA ELECTRICALS, 1577, VIVEKANAND NAGAR, DOUBLE
STORY, GHAZIABAD-UTTAR PRADESH, 201001, Tel: 0120-2702670, Email: [email protected]. KANPUR - CLIPCO
TRADERS, 77/151, LATOUCHE ROAD , KANPUR- UTTAR PRADESH, 208001, Tel: 0512-2314228, Email: [email protected].
UTTARPRADESH: KANPUR - MAGADH INDUSTRIAL COMPANY, 123/414-A, GURU NANAK MARKET, GADARIAN PURVA,
KANPUR- UTTAR PRADESH, 208022, Tel: 0512-2230545, Email: [email protected]. KANPUR - VIRAT ENTERPRISES,
122/230, SAROJINI NAGAR, KANPUR -UTTAR PRADESH, 208012, Tel: 0512-2221264, Email: [email protected].
LUCKNOW - YASH ENGINEERING WORKS, 83, NAYA GAON EAST (BARROW MARKET) LATOUCH ROAD, LUCKNOW-UTTAR
VENUS CINEMA BUILDING, RAILWAY ROAD
BROTHERS, 228/6, HAPUR ROAD, GHAZIABAD-UTTAR PRADESH, 201001, Tel: 0120-4115993, Email:
,
SAHARANPUR -UTTAR PRADESH, 247001, Tel: 0132-2641663, Email:
-
[email protected]. MEERUT - GARG STEEL CENTRE, 419, PATEL GANJ, KABARI BAZAR, MEERUT CITY-UTTAR
PRADESH, 250002, Tel: 0121-2515926, Email: [email protected]. LUCKNOW - NIMBUS INTERNATIONAL, 26, AISH
DIAMOND EDGE, D 59/127, CURCH MISSION COMPOUND, SIGRA, VARANASI-UTTAR PRADESH, 221010, Tel: 0542-2224317,
PRADESH, 211003, Tel: 0532-2418381, Email: [email protected]. HARIDWAR - U & D CORP, 1243, ARYA NAGAR,
KANKHAL-JWALAPUR ROAD, HARIDWAR-UTTRAKHAND, 249404, Tel: 01334-253452, Email: [email protected]. RUDRAPUR -
NATIONAL MACHINERY STORES, 39, GALLA MANDI, U.S. NAGAR, RUDRAPUR-UTTRAKHAND, 263153, Tel: 05944-243417,
WEST BENGAL, 713213, Tel: 0343-2583831, Email: [email protected]. HOWRAH - CUTWELL TOOLS, BELOW WBSEB
OFFICE HOWRAH AMTA ROAD, DASNAGAR HOWRAH, WEST BENGAL, 711105, Tel: 6530670, Email:
[email protected]. KOLKATA - BARDIA TRADING CO., NO. 17 , PRINCEP STREET KOLKATA WEST BENGAL, 700072,
Tel: 2373065, Email: [email protected]. KOLKATA - MACHINERY & TOOLS ( INDIA ), 24,NETAJI SUBHAS ROAD
KOLKATA WEST BENGAL, 700001, Tel: 033-2221-3840, Email: [email protected]. KOLKATA - S.M.B CORPORATION, NO.
218 OLD CHINA BAZAR STREET KOLKATA, 700001, Tel: 22422406/0666, Email: [email protected]. KOLKATA - SUBOL
DUTT
&
SONS PVT. LTD., NO. 13, BRABOURNE ROAD KOLKATA WEST BENGAL, 700001, Tel: 40051156, Email:
[email protected]. KOLKATA - ESKAY CORPORATION, 26, N.S.ROAD(NETHAJI SUBAS ROAD) (GROUND FLOOR)
06.2017
|