English
®
•
•
Whenever you leave your mower
unattended.
ENGLISH
Before checking, cleaning, adjusting
or working on your mower.
•
•
Before clearing a blockage.
If your mower starts to vibrate
abnormally (check immediately).
•
Do not use solvents or cleaning fluids to
clean your mower - use a blunt scraper
to remove grass and dirt.
•
After striking a foreign object, inspect
your mower for damage and make
repairs as necessary.
•
•
Always disconnect from the electrical
supply before cleaning.
•
Never run your mower whilst lying on its
side or attempt to stop the blade -
always allow it to stop on its own.
Do not operate your mower if any parts
are defective; discard all defective parts
and fit new parts before use.
•
•
•
Do not put hands or feet near or under
rotating parts.
•
•
Keep all nuts, bolts and screws tight to
be sure your mower is in a safe working
condition.
Keep clear of discharge openings at all
times.
Use only Black & Decker recommended
replacement parts and accessories.
Start your mower carefully according to
the instructions and with your feet well
away from the blade.
Black & Decker’s policy is one of continuous
improvement to our products and, as such, we
reserve the right to change product specifications
without prior notice.
•
Do not use your mower in the rain and
do not allow it to get wet. Avoid using
your mower in wet grass, if possible.
•
•
•
•
•
Use your mower only in daylight or good
artificial light.
Double insulation
Do not pull your mower towards you or
walk backwards when in operation.
Your mower is double insulated.
This means that all external metal parts are
electrically isolated from the power supply.
This is achieved by placing an extra
insulation barrier between the electrical and
mechanical parts. Double insulation means
greater electrical safety and obviates the
necessity of having your mower earthed.
Do not cross gravel paths or roads whilst
the tines are rotating.
Always be sure of your footing,
particularly on slopes.
Always cut across the face of slopes, never
up and down. Exercise extreme caution
when changing direction on slopes.
•
•
Do not cut excessively steep slopes and
always wear non-slip footwear.
Electrical safety (UK only)
Your mower should always be switched off
Check the grassbag (if supplied) for wear
or damage and replace if necessary.
Never use your mower without the
grassbag in place.
at the mains before disconnecting any plug
and socket connector or extension cables.
!
Fuse replacement
If your mower is supplied with cable fitted
with a non-re-wireable plug:
•
•
Walk, never run. Do not force your mower.
Never pick up or carry your mower while
the motor is running.
•
The plug is fitted with a 13 amp fuse
which is the recommended fuse for
your mower.
•
Ensure the blade has stopped rotating
and take extreme care before lifting your
mower for and during transportation.
•
•
Only use replacement fuses which are
approved to BS1362.
•
Never operate your mower with defective
guards or shields.
When changing the fuse in your plug,
always ensure the fuse cover is refitted.
If the fuse cover is missing or damaged
do not use the plug.
Maintenance and storage
•
Store your mower in a dry place when
not in use, out of the reach of children.
Note: Fuses do not give personal protection
against electric shock.
3
Plug replacement
Handle assembly (Fig. B)
•
•
Disconnect the plug from the supply.
The handles of your mower have been fully
Cut off the plug and dispose of
immediately. Insertion of a detatched
plug into a 13 amp socket outlet may
result in electric shock.
B
assembled prior to delivery, but two minor
operations are required in order to make your
mower ready for use. They are as follows:
Wing nut reversal
•
•
Only fit BS1363A approved plugs fitted
with the correctly rated fuse.
•
The assemblies (8, 9 & 10) which fix the
upper handle (7) to the lower (6) have
been assembled as shown in Fig. B1 to
protect them during transit.
The cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to
their respective points in the plug (see
below). Brown is for “Live” (L) and blue is
for “Neutral” (N).
•
We advise you to dismantle these items
(Fig. B2) and re-assemble (Fig. B3),
taking care not to trap the motor cable
(12) between the handles in the process.
This operation will assist in grassbox
removal/refit.
•
Before replacing the top cover of the
mains plug ensure that the cable restraint
is holding the outer sheath on the cable
firmly and that the two leads are correctly
fixed at the terminal screws.
Unfolding the upper handle
The upper handle (7) can now be unfolded
into the position shown in Fig. A, and the
wing nuts (8, 9 &10) tightened firmly, taking
care not to trap the motor cable (12) in the
process.
Fit the
recommended
fuse
Fit a
BS1363A
approved
plug
Connect blue
to N (neutral)
Grassbox assembly (Fig. C)
•
The grassbox (3 & 4) can now be
withdrawn through the handle tube (6),
and the grassbox door can be opened
as indicated by the arrow.
Connect brown
to L (live)
C
Make sure that the
outer sheath of the
cable is held firmly
by the clamp
•
To refit the box, reverse the process
using the arrow heads (shown in inset) to
re-align the box into its correct position.
240 volts AC only.
Never use a light
socket
Warning! Never connect live or neutral wires
to the earth pin marked “E” or
Finished mower check
Check your fully assembled mower now for any signs
of damage or missing parts. The finished mower
should look like Fig. A.
.
!
!
Note: Do not wire an extension cable directly
into your mower yourself. Instead, take your
mower to your nearest Black & Decker
service agent.
Increased safety can be obtained by having
a qualified electrician install a high sensitivity
(30mA) circuit breaker in the house wiring.
If you do not have such a circuit breaker
installed, or you do not wish to have one
installed, then we strongly recommend that
the electrical power to your mower be
supplied through a high sensitivity residual
current device (RCD). The RCD is designed
to provide a high degree of personal
Cutter blade check (Fig. D)
Warning! Disconnect your mower from the
electrical supply before checking the blade.
!
All manufactured mowers are checked prior
D
to packing to ensure that the cutter blade
(23) is secure, but for your safety we would
advise you to re-check this by the following
method:
•
•
Remove the grassbox (3 & 4).
protection against harmful electric current
should fault conditions occur.
Turn your mower over onto its side so
that the underside of the cutter deck (1)
is exposed.
Warning! The use of an RCD or other circuit
breaker unit does not release the operator of
your mower from the safety instructions and
safe working practices given in this manual.
•
Using a cloth placed over the blade (23),
grip the blade and, using the spanner
provided (20), tighten the nut (21) in a
clockwise direction.
4
Switchbox operation (Fig. E)
ENGLISH
We strongly recommend that prior to
E
connecting your mower to the mains, you
understand fully the switchbox operation.
The operation is as follows:
To start your mower
Height of cut adjustment (Fig. D & G)
•
•
Grasp the handle (7) with both hands.
Tilt your mower slightly to one side.
The cut height of your mower is adjusted by
G
means of blade spacers (22 & 24). The
method for this operation is as follows:
Note: Failure to do this may result in an
unsightly ring being cut in your lawn.
•
Ensure your mower is disconnected from
the mains supply.
•
Remove your left hand from the handle
(7) and depress the lock-off button (15).
•
Turn your mower onto its side so that the
underside of the cutter deck (1) is
exposed.
•
Whilst this button is depressed, grasp
the switchbox lever (14) with your right
hand and squeeze towards the handle (7).
•
•
•
•
Using a cloth placed over the blade (23),
grip the blade and, using the spanner
provided (20), undo the nut (21) in an
anti-clockwise direction.
•
•
Your mower will now operate.
Release the lock-off button (15) and
return your left hand to the handle tube.
Remove the blade nut, spacers and
blade (21-24) and re-assemble to give
the cut height required. See Fig. G,
showing the 6 cut heights available.
Note: If the lock-off button (15) is not
depressed in the order above, your mower
will not operate and the lever (14) will not
engage with the switch. This is a safety
feature!
Once the cut height is selected, re-
assemble the blade, ensuring the cutter
blade (23) is assembled with the cutting
tips downwards as shown in Fig. D.
D
To stop your mower
•
Tilt your mower slightly to one side.
Note: Failure to do this may result in an
unsightly ring being cut in your lawn.
Ensure the blade nut (21) is tight.
Note: Your mower is supplied with a cut
height of 11mm (Fig. G).
•
•
Release the switchbox lever (14).
When your mower has stopped rotating,
lower it back onto the lawn.
•
Always re-fit 3 spacers and never fit more
or your mower will become unsafe.
Handle operation (Fig. F)
Carrying your mower (Fig. H)
The normal operating range of the handle is
Disconnect your mower from the mains.
F
shown in Fig. F, as angle F1. This should
enable a comfortable working position to
be achieved.
H
Remove the grassbox, lower the handle to
the flat “park” position and then, holding one
handle near the pivot block and carry with
the blade pointing away from you.
If you wish to store your mower by hanging it
on the wall (angle F2), proceed as follows:
•
•
•
Disconnect it from the mains.
Remove the grassbox.
How to use your mower (Fig. J)
Observe all of the relevant warnings when
Lower the handle to the bottom of its
normal range, then pull the handle
towards you and lower it to the ground.
(Do not drop the handle as it may
damage the switchbox.)
using your mower.
!
We recommend the directional method of
operation to obtain maximum cutting
performance from your mower and to reduce
the risk of the trailing extension lead from
entering the cutting path.
Your mower can now be lifted and stored on
the wall if required.
•
Place the bulk of the extension cable
on the lawn close to the starting point
(Fig. J, position 1).
•
Hold the handle assembly with both
hands.
5
Your switch box incorporates a cable
restraint. To fix the cable to the restraint,
proceed as follows:
Overload protection (GX635 only)
Your mower is fitted with overload protection.
The reset button (25) can be found on the switch box
(Fig. A).
•
Bring the socket end of the extension
cable from behind and connect it to your
mower plug.
If you work too quickly in long grass, or in heavy
cutting conditions, you may overload the motor.
This will be indicated by a significant drop in speed,
and eventually the overload protection will operate.
This is not a fault but a safety device to protect
your mower.
•
•
Form a loop on your extension cable
close to the coupler (Fig. E).
Push the loop through the slot from the
opposite side of the restraint hook,
position the loop over the hook and pull
the cable back through the slot. Your
cable will now be restrained.
When this occurs, release the switch and wait for
2 to 3 minutes to allow the motor to cool, then press
the reset button (25) and restart by operating the
switch lever and lock-off button.
•
The extension cable should now fall
away from your mower and behind the
operator, ready for use.
If the cut-out operates again within 10 minutes you
should increase the height of cut (see “Height of cut
adjustment”) and walk more slowly.
Warning! Do not attempt to operate your
mower with one hand - you must guide it
with both hands.
!
Severe overloading may result in a longer delay on
restarting. In such cases, after resetting, you should
allow the motor to cool.
•
Lift the handle up to release it from the
park position.
•
Proceed down the cutting area as shown
in Fig. Ja, working from position 1
towards position 2 and, on reaching
position 2, turn to the right and proceed
towards position 3. Continue to the end
of the cutting area, turn to the left, and
proceed towards position 4. Continue in
the same manner as shown in Fig. Ja,
always working away from the cable. Do
not adopt the method shown in Fig. Jb,
working towards the cable, as this can
be dangerous.
Blade maintenance
J
The steel blade is designed to give a fine
finish in long or tough grass. The blade will
continue to cut even when it has become
blunt or burred. There is no need for it to be
razor sharp.
If, however, because of damage or wear the
cutting performance deteriorates, then your
mower may require a new blade, or at least
the existing blade to be sharpened.
We recommend that the steel blade is
sharpened or a new blade fitted at the
beginning of each season.
•
For best grass pick-up, push your
mower in straight lines.
Your mower will continue to operate whilst
you are pressing the switch lever. If you
release it for any reason you will not be able
to press it again until you have pressed the
safety lock-off button on the switch box.
This feature prevents accidental restart.
Replacement blades (cat. no. A6184) are
available from Black & Decker service agents.
Warning! When fitting a new blade use only
the Black & Decker replacement part
specified for your mower - do not attempt to
fit any other blade.
!
When you have finished using your mower
we recommend that you clean all debris from
it before putting it away. Refer to the “Care
and maintenance” section.
Fitting a new blade
Observe all the relevant warnings before
changing blades.
Note: To obtain the best results cut your
lawn or grassed area regularly and do not
cut when the grass is wet.
!
Details on the fitment of new steel blades are
given in “Cut height adjustment”.
Handy hints
•
Before starting your mower on grass always tilt it
to one side slightly and allow it to run up to
maximum speed before commencing to cut the
grass. This will maximise the hover effect and will
prevent the blades from digging into the grass.
6
•
On long grass, above 10cm (4 inches), use two
cuts to get a close finish. We recommend that
the first cut should be taken with the blade set at
maximum height of cut and the second taken
with it set at medium or close. This will prove to
be easier and give a better overall finish to
your lawn.
ENGLISH
Symptoms
Possible cause Remedy
No noise and
Faulty electrical Plug your mower
Care and maintenance
the blade does connection.
not move.
into an alternative
compatible
electrical supply.
The advice given in this section covers the
general care and maintenance of the main
body of your mower. Advice relating to the
blades is given in “Maintenance of blades”.
Check if a new
fuse is required.
Re-tighten and
Warning! Do not use an extension cable
which shows signs of damage. Fit a new
cable completely - do not make any
permanent or temporary repairs.
check all electrical
connections in the
extension cables.
!
Overload cut-
out operates.
Reset overload
cut-out.
•
Always keep your mower clean and free
from grass cuttings, especially the
underside of the cutter cover and the air
vents.
Grass not being The grassbox
Empty the
grassbox.
picked up.
is full.
•
•
Check all electrical cables at regular
intervals, looking for signs of wear,
abrasion or other damage.
The pickup inlet Remove grassbox
in the grassbox and clear the hole
is blocked.
in the base.
At the end of each cutting session we
recommend that the build up of grass on
the underside of the cutter cover is
removed using a blunt scraper or the
spanner supplied.
Air paths are
blocked.
Remove grassbox
and clear the filter
in the roof of the
grassbox.
Also clean the
filter on the back
of your mower.
•
•
Remove grass cuttings from the slot
between the pivot block flanges.
Clean all plastic components with a
damp cloth.
The cut height Disconnect from
is too low in
long grass.
the electrical
supply. Reset
the blade height
to a higher
Caution: Do not use solvents or cleaning
fluids as these may damage the plastic
components of your mower.
position.
Your mower
is being moved in a straight line to
Push your mower
Fault finding
If your mower does not operate correctly,
side to side.
maximise pick up.
use the following table to locate the problem.
Motor stalled.
The motor is
overloading in
long, thick
grass.
Disconnect from
the electrical
supply. Reset the
blade height
to a higher
Warning! Always disconnect your mower
from the electrical supply before carrying out
any inspection.
!
Symptoms
Possible cause Remedy
position.
Motor buzzes
but blade does
not move.
Blade jammed. Disconnect from
Poor cutting
performance.
Blade damaged Disconnect from
due to impact the electrical
on large stones, supply. Check the
tree stumps, blade for damage.
paving stones or Replace with a
similar objects. new blade,
if necessary.
the electrical
supply.
Remove the
obstruction from
the blade.
No noise and
Faulty electrical Disconnect from
the blade does connection.
not move.
the electrical
supply.
7
•
Failures due to usage not in accordance with
instructions and recommendations contained in
this manual.
ENGLISH
The use of other than genuine Black & Decker
accessories and parts may damage or reduce the
performance of your Black & Decker mower and may
render the guarantee void.
What to do if your mower needs
repair
For after sales service please refer to the section
‘Lawnmowers & Garden’ within your local
Yellow Pages.
Black & Decker after sales service
(UK, Australia and New Zealand only)
Black & Decker offers a nationwide network of
authorised service agents. The use of other than
genuine Black & Decker accessories and parts may
damage or reduce the performance of your
Black & Decker product and may also endanger the
user. The terms and conditions of the warranty may
also be effected.
Unwanted products and the
environment
Should you find one day that your mower
needs replacement, or is of no further
use to you, think of the protection of the
environment. Black & Decker service agents
will accept your old mower and will dispose of
it in an environmentally safe way.
It is our aim that all Black & Decker customers should
be totally satisfied with their Black & Decker product
and after sales service, if help or advice is needed
please contact a local Black & Decker authorised
repair agent who will be happy to help. Full details of
our after sales service can be obtained from any of
our Black & Decker authorised repair agents.
Black & Decker lawn and garden
guarantee
This guarantee provides 36 months parts cover
and 12 months labour (UK), 24 months parts
cover and labour (Australia and New Zealand).
In all cases proof of purchase will be required.
Other Black & Decker products
(UK only)
Black & Decker has a full range of outdoor power
tools that make life easy in the garden. If you would
like further information on other products, please
contact the Black & Decker Service Information
Centre at the address towards the back of this
manual, or contact your Black & Decker stockist.
lf your Black & Decker mower becomes defective,
within the guarantee period, due to faulty materials
and workmanship, we guarantee to either replace all
defective parts, or at our discretion, replace your
mower free of charge, provided that:
•
Your mower is returned to one of our authorised
repair agents with evidence of purchase.
Lawnmowers
Chainsaws
String trimmers
Lawnrakers
Compost shredders
Blade trimmers
Cordless trimsaws
Cordless shears
Leafbusters
•
Your mower has been used within the
parameters of its consumer classification.
Cordless brooms
Cordless shrubbers
Hedgetrimmers
•
•
Your mower has not been used for hire purposes.
Repairs have not been attempted by anyone
other than our authorised repair agents.
EC Declaration of Conformity
•
The failure represents normal wear and tear.
We declare that units:
This guarantee is offered as an extra benefit and is
additional to your statutory rights.
GX530, GX635
conform to: 89/392/EEC, 89/336/EEC,
73/23/EEC, EN60335, EN55104, EN55014
Our guarantee policy
Failures due to the following are not covered:
A weighted sound pressure 96dB (A)
A weighted sound power 109dB (A)
Hand/arm weighted vibration <2.5m/s2
•
Replacing worn or damaged blades, nylon line
and chains, or cables damaged during storage
or use. These are regarded as replacement items
which wear during normal usage.
Brian Cooke
•
Failures as a result of sudden impact or obvious
abuse.
Director of Engineering
Black & Decker Ltd, Spennymoor, County Durham
DL16 6JG, United Kingdom
8
Australia
Black & Decker (A’asia) Pty Ltd
Tel: 03 9213 8200
286-288 Maroondah Highway, North Croydon, Victoria 3136 Fax: 03 9726 7150
New Zealand
South Africa
Black & Decker
483 Great South Road, Penrose, Auckland
Tel: 09 579 7600
Fax: 09 579 8200
Black & Decker South Africa (Pty) Ltd
Suite no 107, PostNet X65, Halfway House 1685
Tel: 011 314 4431
Fax: 011 314 4435
United Kingdom Black & Decker
210 Bath Road, Slough
Berkshire SL1 3YD
Tel: 01753 574277
Tlx: 848317 BAND MH
Fax: 01753 551155
®
Part no. 375813-16 9/97.1
Part no. 375813-16 9/97.1
®
GX530
GX635
7
A
B
B1
14,15
12
25
8.9.10
B2
6
7
9
10
1
6
3,4
8
C
B3
3
4
D
G
a)
d)
22
24
23
21
24
22
b)
c)
e)
f)
24
23
22
24
24
22
23
21
22
26
21
20
24
22
24
22
23
21
H
7
E
15
14
a
b
2
J
F
3
F1
4
1
F2
✓ ✗
|