GKC1825L20
F
H
J
G
I
K
3
L
M
N
O
P
Q
4
R
S
T
U
V
5
(Original instructions)
ENGLISH
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Intended use
Your BLACK+DECKERTM chainsaw has been designed for
pruning and felling trees and cutting logs. This tool is intended
for consumer use only.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
@
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
6
(Original instructions)
ENGLISH
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Additional power tool safety warnings
Warning! Additional safety warnings for
chainsaws
@
u Keep all parts of the body away from the saw chain
when the chainsaw is operating. Before you start the
chainsaw, make sure the saw chain is not contacting
anything. A moment of inattention while operating chain
saws may cause entanglement of your clothing or body
with the chain saw.
u Always hold the chainsaw with your right hand on the
rear handle and your left hand on the front handle.
Holding the chainsaw with a reversed hand configuration
increases the risk of personal injury and should never be
done.
u Hold the power tool by insulated gripping surfaces
only, because the saw chain may contact hidden
wiring. Saw chains contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
u Wear safety glasses and hearing protection. Further
protective equipment for head, hands, legs and feet is
recommended. Adequate protective clothing will reduce
personal injury by flying debris or accidental contact with
the saw chain.
u Do not operate a chainsaw in a tree. Operation of a
chainsaw while up in a tree may result in personal injury.
u Always keep proper footing and operate the chain saw
only when standing on fixed, secure and level surface.
Slippery or unstable surfaces such as ladders may cause
a loss of balance or control of the chainsaw.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
u When cutting a limb that is under tension be alert
for spring back. When the tension in the wood fibres is
released the spring loaded limb may strike the operator
and/or throw the chain saw out of control.
u Use extreme caution when cutting brush and saplings.
The slender material may catch the saw chain and be
whipped toward you or pull you off balance.
u Carry the chain saw by the front handle with the chain
saw switched off and away from your body. When
transporting or storing the chainsaw always fit the
guide bar cover. Proper handling of the chain saw will
reduce the likelihood of accidental contact with the moving
saw chain.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
u Follow instructions for lubricating, chain tensioning
and changing accessories. Improperly tensioned or
lubricated chain may either break or increase the chance
for kickback
u Keep handles dry, clean, and free from oil and grease.
Greasy, oily handles are slippery causing loss of control.
7
(Original instructions)
ENGLISH
u Cut wood only. Do not use chainsaw for purposes not
intended. For example: do not use the chainsaw for
cutting plastic, masonry or non-wood building materi-
als. Use of the chainsaw for operations different than
intended could result in a hazardous situation.
u We recommend that when carrying the chainsaw that you
remove the battery and make sure that the saw chain is
facing backwards.
u Maintain your chainsaw when not in use. Do not store
your chainsaw for any length of time without first remov-
ing the saw chain and guide bar which should be kept
immersed in oil. Store all parts of your chainsaw in a dry,
secure place out of reach of children.
u We recommend you drain the oil reservoir prior to storage.
u Be sure of your footing and pre-plan a safe exit from a
falling tree or branches.
u Use wedges to help control felling and prevent binding the
guide bar and saw chain in the cut.
Causes and operator prevention of kickback
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches
the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse reac-
tion, kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may
push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of
the chainsaw which could result in serious personal injury.
Do not rely exclusively upon the safety devices built into your
chainsaw. As a chainsaw user, you should take several steps
to keep your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and / or incorrect operat-
ing procedures or conditions and can be avoided by taking
proper precautions as given below:
u Saw chain care. Keep the saw chain sharp and snug on
the guide bar. Ensure the saw chain and guide bar are
clean and well oiled. Keep handles dry, clean and free
from oil and grease.
Avoid cutting
u Prepared timber.
u Into the ground.
u Into wire fences, nails. etc.
u Maintain a firm grip, with thumbs and fingers encir-
cling the chainsaw handles. With both hands on the
chainsaw, position your body and arm to allow you to
resist kickback forces. Kickback forces can be control-
led by the operator, if proper precautions are taken. Do not
let go of the chainsaw.
u Do not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact and
enables better control of the chainsaw in unexpected situ-
ations.
u Only use replacement guide bars and chains specified
by the manufacturer. Incorrect replacement guide bars
and chains may cause chain breakage and/ or kickback.
u Follow the manufacturer's sharpening and mainte-
nance instructions for the saw chain. Decreasing the
depth gauge height can lead to increased kickback.
u Striking metal, cement or any other hard material near the
wood, or buried in the wood can cause kickback.
u A dull or loose chain can cause kickback.
Additional safety instructions
u Ensure someone is nearby (but at a safe distance) in case
of an accident.
u If for any reason you have to touch the saw chain, make
sure your chainsaw is disconnected from the mains.
u The noise from this product can exceed 85 dB(A). We
therefore recommend you take appropriate measures for
the protection of hearing.
u When handling the product the chain bar may become
hot, handle with care.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Do not try to insert into a previous cut. As this could cause
kickback. Make a fresh cut every time.
u Children should be supervised to ensure that they do not
play with the appliance.
Safety recommendations for the chainsaw
u We strongly recommend that first time users obtain practi-
cal instruction in the use of the chainsaw and protective
equipment from an experienced user. Initial practice
should be completed sawing logs on a saw horse or
cradle.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
8
(Original instructions)
ENGLISH
u Injuries caused when changing any parts, blades or ac-
cessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
Caution: Do not over tighten. Tighten by
hand. Finger tight only.
u Impairment of hearing.
Additional safety instructions for batteries and
chargers
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
Do not attempt to charge damaged batteries.
p
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Chargers
u Use your BLACK+DECKER charger only to charge the
battery in the tool with which it was supplied. Other batter-
ies could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
Labels on tool
The following pictograms are shown on the tool:
u Do not probe the charger.
The charger is intended for indoor use only.
Warning! To reduce the risk of injury, the user
must read the instruction manual.
$
:
Read the instruction manual before use.
+
Wear safety glasses or goggles when operating
this tool.
O
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
Wear ear protection when operating this tool.
#
N
Do not expose the tool to rain or high humidity.
R
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Directive 2000/14/EC guaranteed sound power.
9
(Original instructions)
ENGLISH
u Check the tension as described below. Do not overtighten.
u Tighten the chain adjust locking knob (9) (L).
Features
1. On/off switch
2. Lock-off button
3. Oil cap
Checking and adjusting the chain tension (fig. K)
Before use and after every 10 minutes of use, you must check
the chain tension.
4. Front guard
5. Chain tension adjustment ring
6. Chain
u Remove the battery (12).
u Lightly pull on the chain (6) as shown (inset fig. K). The
tension is correct when the chain (6) snaps back after
being pulled 3 mm away from the guide bar (7). There
should be no "sag" between the guide bar (7) and the
chain (6) on the underside.
Note: Do not over-tension the chain as this will lead to
excessive wear and will reduce the life of the guide bar and
the chain.
7. Guide bar
8. Chain sheath
9. Chain adjust locking knob
10. Chain cover assembly
11. Oil level indicator
12. Battery
Assembly
Note: When the chain is new, check the tension frequently
(after disconnecting from the mains) during the first 2 hours of
use because a new chain stretches slightly.
Warning! Always wear protective gloves when
working on your chainsaw.
@
@
Warning! Before performing any assembly
or maintenance on power tools, switch off and
remove the battery.
To increase the tension (fig. J, K & L)
u Turn the chain adjust locking knob (9) 180 degrees anti-
clockwise to release the tension. (fig. J)
u Tension the chain using the chain tension adjusting ring
(5), turn clockwise to tighten (fig K).
u Tighten the chain adjust locking knob (9) (fig. L).
Warning! Remove the cable tie that attaches
the chain to the chainbar before assembly.
@
Fitting and removing the battery (fig. M)
u To fit the battery (12), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
u To remove the battery, push the release buttons (16) while
at the same time pulling the battery out of the receptacle.
Fitting the guide bar and chain. (fig. A - L)
u Place the chainsaw onto a stable surface (fig. A).
u Fully loosen the chain adjust locking knob (9) (fig. B).
u Remove the chain cover assembly (10) (fig. C).
u Turn the tension adjust ring (5) anti-clockwise as far as it
will go so the arrow on the tension adjust ring (5) lines up
with the marker on the chain cover assembly (13) (fig. D)
u Place the chain (6) over the guide bar (7) making sure that
the saw chain cutters on the upper part of the guide bar
(7) face towards the front (fig. E).
u Guide the chain (6) around the guide bar (7) and pull it to
create a loop to one side at the rear end of the guide bar
(7).
u Guide the chain (6) around the drive sprocket (14). Place
the guide bar (7) onto the bar location studs (15) (fig. F &
G).
u Place the chain cover assembly (10) onto the chainsaw
(fig. H) making sure the arrows are aligned (fig. I).
u Turn the chain adjust locking knob (9) clockwise to attach
the chain cover assembly (10) and lightly tighten (fig. I).
u Turn the chain adjust locking knob (9) 180 degrees anti-
clockwise to release the tension (fig J).
u Turn the chain tension adjust ring (5) clockwise until the
chain (6) is tight. Make sure that the chain (6) is snug
around the guide bar (7) (fig. K).
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. N)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
10
(Original instructions)
ENGLISH
u To charge the battery (12), insert it into the charger (19).
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
u Plug in the charger and switch on at the mains.
The charging indicator (18) will blink.
The charge is complete when the charging indicator (18)
switches to continuously on. The charger and the battery
can be left connected indefinitely. The charging indicator will
switch on as the charger occasionally tops up the battery
charge.
Never use waste oil, thick oil or very thin sewing machine oil.
These may damage your chainsaw.
The saw chain (6) must be oiled before each use and after
cleaning using only the correct grade of oil (cat. no. A6023-
QZ).
u Lubricate the saw chain (6) by slowly pressing the bulb
(17) (fig. O) on the oil cap (3) four time before making
each cut. Hold the bulb down for 1 second each time.
Switching on (fig. O)
u Grip your chainsaw firmly with both hands. Pull the lock-off
button (2) with your thumb and then push the on/off switch
(1) to start.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
u When the motor starts, remove your thumb from the lock-
off button (2) and grip the handle firmly.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
charger indicator glowing indefinitely. The charger will keep
the battery pack fresh and fully charged.
Do not force the tool, allow the tool to do the work. It will do
a better and safer job at the speed for which it is designed.
Excessive force will stretch the saw chain (6).
Charger diagnostics
If the saw chain (6) or guide bar (7) becomes
jammed
u Switch the tool off.
If the charger detects a weak or damaged battery, the charg-
ing indicator (18) will flash red at a fast rate. Proceed as
follows:
u Remove the battery (12).
u Re-insert the battery (12).
u Open the cut with wedges to relieve the strain on the
guide bar (7). Do not try to wrench the chainsaw free.
u Start a fresh cut.
u If the charging indicators continues flashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
u If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the charger indicator will alternately blink red, fast
and slow, one flash at each speed and repeat.
Felling (fig. P, Q & R)
Inexperienced users should not attempt to fell trees. The user
may suffer injury or cause damage to property as a result of
failure to control the direction of fall, the tree may splinter or
damaged/dead branches may fall during cutting.
The safe distance between a tree to be felled and bystanders,
buildings and other objects is at least 2 1/2 times the height of
the tree. Any bystander, building or object within this distance
is at risk from being struck by the tree when felled.
Before attempting to fell a tree:
Filling the oil reservoir (fig. O)
u Make sure that there are no local by-laws or regulations
that would prohibit or control the felling of the tree.
u Consider all conditions that may affect the direction of fall,
including:
u Remove the oil cap (3) and fill the reservoir with the
recommended chain oil. You can see the oil level in the oil
level indicator (11). Refit the oil cap (3).
u Periodically switch off and check the oil level indicator
(11); if it is less than a quarter full, remove the battery from
the chainsaw and refill with the correct oil.
u The intended direction of fall.
u The natural lean of the tree.
u
Any unusual heavy limb structure or decay.
u Surrounding trees and obstacles including overhead
lines and underground drains.
Oiling the chain
We recommend that you use only Black & Decker oil during
the lifetime of your chainsaw because mixtures of different oils
could lead to the oil becoming degraded, which can drastically
shorten the lifetime of the saw chain and create additional
risks.
u The wind speed and direction.
Pre-plan a safe exit from falling trees or branches. Make sure
that the exit route is clear of obstacles that would prevent or
hinder movement. Remember that wet grass and freshly cut
bark is slippery.
11
(Original instructions)
ENGLISH
u Do not attempt to fell trees where the tree diameter is
greater than the cutting length of the chainsaw.
u Cut a direction notch to determine the direction of fall.
u Make a horizontal cut to a depth of between 1/5th and
1/3rd of the diameter of the tree, perpendicular to the line
of fall at the base of the tree (fig. P).
When supported at one end:
u First cut one third up to avoid splintering and second, cut
down to prevent splintering.
When on a slope:
u Always stand on the uphill side.
u Make a second cut from above to intersect with the first
and make a notch of about 45°.
u Make a single horizontal felling cut from the other side 25
mm to 50 mm above the centre of the direction notch. (fig.
Q). Do not cut through to the direction notch, you could
lose control of the direction of fall.
When attempting to cut a log on the ground (fig. T):
u Secure the workpiece using chocks or wedges. The user
or a bystander should not steady the log by sitting or
standing on it. Make sure that the saw chain does not
contact the ground.
u Drive a wedge or wedges into the felling cut to open it and
drop the tree (fig. R).
When using a saw horse (fig. U):
This is strongly recommended whenever possible.
u Position the log in a stable position. Always cut on the
outside of the saw horse arms. Use clamps or straps to
secure the workpiece.
Pruning trees
Make sure that there are no local by-laws or regulations that
would prohibit or control the pruning of the tree limbs. Pruning
should only be undertaken by experienced users there is an
increased risk of the saw chain pinching and kick back.
Limbing (fig. V)
Removing the branches from a fallen tree. When limbing,
leave larger lower limbs to support the log off the ground.
Remove the small limbs in one cut. Branches under tension
should be cut from the bottom of the branch towards the top to
avoid binding the chain saw.
Trim limbs from opposite side keeping tree stem between you
and saw. Never make cuts with saw between your legs or
straddle the limb to be cut.
Before pruning consideration should be given to
conditions affecting the direction of fall including:
u The length and weight of the branch to be cut.
u Any unusual heavy limb structure or decay.
u Surrounding trees and obstacles including overhead.
u The wind speed and direction.
u The branch being intertwined with other branches.
The operator should consider access to the tree limb and the
direction of fall. The tree branch is liable to swing towards
the tree trunk. In addition to the user bystanders, objects and
property below the branch will be at risk.
Troubleshooting
Problem
Possible cause
Possible solution
Lock button not
pressed.
u To avoid splintering, make the first cut in an upward direc-
tion to a maximum depth of one third the diameter of the
branch.
Tool will not start
Press the lock button.
Battery not fitted
Fit the battery
u Make the second cut downwards to meet the first.
Battery not charged
Charge the battery
Battery not fitted
Remove then re-fit the
Logging (fig. S, T & U)
corectly
battery
How you should cut depends on how the log is supported.
Use a saw horse whenever possible. Always start a cut with
the saw chain running and the spiked bumper (20) in contact
with the wood (fig. S). To complete the cut use a pivoting ac-
tion of the spiked bumper against the wood.
Chain tension is too
slack
Chain does not stop
within 2 seconds
when the tool is
switched off
Check chain tension
When supported along its whole length:
u Make a downward cut, but avoid cutting the earth as this
will blunt your saw chain quickly.
When supported at both ends:
u First, cut one third down to avoid splintering and second,
cut up to meet the first cut.
12
(Original instructions)
ENGLISH
u Make sure that the guard is clean and free from debris.
u Oil sprocket nose and chain bar via the sprocket lubrica-
tion holes (21) (fig. E). This ensures an even distribution of
wear around the guide bar rails.
Problem
Possible cause
Possible solution
Bar/chain appear hot/
smoking
Oil tank empty
Check oil tank level
Oil hole blocked on
chain bar
Clean oil holes (21 - fig.
E) and clear the groove
around the edge of the
chainbar.
Saw chain sharpening
If you are to get the best possible performance from the tool it
is important to keep the teeth of the saw chain sharp.
Guidance for this procedure is found on the sharpener pack-
age.
Chain tension is too
tight
Check chain tension
Guide bar sprocket
nose needs greasing
Oil the guide bar
sprocket nose
Replacing worn out saw chains
Replacement saw chains are available through retailers or
Black & Decker service agents. Always use genuine spare
parts.
Check/modify chain
Chainsaw does not
cut well
Chain on backwards
direction
Sharpen
Empty oil from tank and
replace
Chainsaw not using
oil
Debris in tank
Saw chain sharpness
The saw chain cutters will blunt immediately if they touch the
ground or a nail while cutting.
Remove debris from
hole
Oil hole in cap blocked
Debris in chain bar
Remove debris and
clean the chain bar
Saw chain tension
Regularly check the saw chain tension.
Debris in oil outlet
Battery depleted
Remove debris
What to do if your chainsaw needs repair.
Re-charge battery if
required.
Chainsaw stops
Your chainsaw is manufactured in accordance with the rel-
evant safety requirements. Repairs should only be carried out
by a qualified person using original spare parts otherwise this
may result in considerable danger to the user. We recommend
you keep this user manual in a safe place.
suddnely during use
Leave the battery to
cool for atleast 30
minutes before
Battery too hot
proceeding or charging.
Protecting the environment
Restart the chainsaw.
Let the tool work at its
own pace. Do not
overload .
Voltage limit protection
Separate collection. This product must not be
disposed of with normal household waste.
Maintenance
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
Regular maintenance ensures a long effective life for the tool.
We recommend you make the following checks on a regular
basis.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
Warning! Before performing any maintenance on power tools:
u Switch off and disconnect the tool from the mains supply.
z
Oil level
The level in the reservoir should not be allowed to fall below
a quarter full.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Saw chain and guide bar
u After every few hours of use and before storage, remove
the guide bar (7) and the saw chain (6) and clean them
thoroughly.
13
(Original instructions)
ENGLISH
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
%
GKC1825L20
Black & Decker declares that these products described under
"technical data" are in compliance with:
Technical data
2006/42/EC, EN 60745-1, EN 60745-2-13
2006/42/EC, Chain Saw, Annex IV
GKC1825L20 (H1)
Voltage
Vdc
18
DEKRA Certification B.V., Utrechtseweg 310,
Bar length
mm
mm
m/sm
mm
ml
250
250
3.5
250
55
6802 ED Arnhem, The Netherlands
Max bar length
Chain speed (No-load)
Max cutting length
Oil capacity
Notified Body ID No.: 0344
Level of accoustic power according to
2000/14/EC (Article 13, Annex III):
L
WA (measure sound power) 90.5 dB(A)
Weight
Battery
Voltage
Capacity
Type
kg
3.1
Uncertainty (K) 1.5 dB(A)
BL2018
LWA (guaranteed sound power) 92 dB(A)
VDC
Ah
18
These products also comply with directive 2014/30/EU &
2011/65/EU. For more information, please contact Black &
Decker at the following address or refer to the back of the
2.0
Li-Ion
Charger
905902** (typ. 1)
manual.
Input Voltage
Output Voltage
Current
VAC
VDC
mA
h
100 - 240
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of Black &
8 - 20
Decker.
400
5
Approx. charge time
Level of sound pressure according to EN 60745:
LpA (sound pressure) 70.5 dB(A), Uncertainty (K) 1.5 dB(A)
L
WA (sound power) 90.5 dB(A), Uncertainty (K) 1.5 dB(A)
R. Laverick
Engineering Manager
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah) 4.49 m/s2, uncertainty (K) 1.5 m/s2
United Kingdom
30/06/2014
14
(Original instructions)
ENGLISH
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
by contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
your new Black & Decker product and to be kept up to date
on new products and special offers. Further information on the
Black & Decker brand and our range of products is available
15
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel.
Fax
03-8720 5100
03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel.
Fax
+64 9 259 1133
+64 9 259 1122
Aukland 1060
United Kingdom &
Republic Of Ireland
Black & Decker
210 Bath Road
Tel.
Fax
01753 511234
01753 512365
Slough, Berkshire SL1 3YD
90613602 REV-0
06/2014
|