BLACK DECKER EMAX38I User Manual

EMax34i  
EMax34s  
EMax38i  
EMax42i  
(Original instructions)  
ENGLISH  
u Move the lever towards the rear of the appliance to lower  
the height of cut.  
u Switch the appliance on as described above.  
u Proceed as shown in fig. P1  
u Move the lever towards the front of the appliance to raise  
the height of cut.  
u Push the height adjustment lever (7) into one of the 6  
height locations.  
Note: The height of cut can be viewed on the height of cut  
gauge (8) on the side of the unit.  
u Move from position 1 to position 2.  
u Turn right and proceed towards position 3.  
u Turn left and move towards position 4.  
u Repeat the above procedure as required.  
Warning: Do not work towards the cable as shown in fig. P2.  
EdgeMax (fig. K1 & K2)  
EdgeMax allows you to cut grass right up to the edge of a wall  
Switching on and off (fig. I)  
or fence (fig K1).  
Switching on  
EdgeMax allows you to accurately cut grass right up to the  
edge of your lawn (fig K2).  
u With the lawnmower parallel with the edge of your lawn.  
u Push the lawnmower along the edge of the lawn. Ensure  
that the EdgeMax (9) is slightly over the edge of your lawn  
(fig.K2)  
u Push in and hold the lock-off button (27).  
u Pull the on/off switch (2) towards the handle.  
u Release the lock-off button.  
Switching off  
Note: The roller underneath the appliance provides stability  
when mowing over the edge of your lawn.  
u Release the on/off switch (2).  
Warning: Never attempt to lock a switch in the on position.  
Compact&Go (fig. J) (EMax34i, EMax38i & EMax42i  
only)  
When the grass collection box is full you can compact the  
grass in the collection box. You can determine how full the  
grass collection box is by looking through the clear grass flap  
(11).  
Mowing (fig. P1 & P2) (EMax38i & EMax42i only)  
We recommend to use your mower as outlined in this section  
in order to achieve optimum results and to reduce the risk of  
cutting the mains cable.  
u Loop the mains cable through the intelligent cable  
management system (4) as shown (fig. H) ensue that you  
leave approximately 100 cm of cable between the switch-  
box (1) and the intelligent cable management restraint (4).  
u Ensure that the cable restraint can slide freely from one  
handle to the other.  
u Release the on/off switch (2).  
u Using your right foot, press the grass compaction lever  
(29) all the way down until it locks into place.  
Note: The grass in the collection box is now compressed into  
the rear of the box. You may continue mowing until the grass  
collection box becomes full.  
u Place the bulk of the mains cable on the lawn, close to the  
starting point (position 1 in fig. P1).  
u Switch the appliance on as described above.  
u Proceed as shown in fig. P1  
u Move from position 1 to position 2.  
Emptying the grass collection box (fig. J) (EMax34i,  
EMax38i & EMax42i only)  
u Turn right, stepping over the cable and proceed towards  
position 3. The cable restraint will slide from one side of  
the handle to the other ensuring that the cable is laid out  
away from the cutting blade.  
u Turn left, stepping over the cable and move towards posi-  
tion 4. The cable restraint will slide from one side of the  
handle to the other ensuring that the cable is laid out away  
from the cutting blade.  
u Release the on/off switch (2).  
u Remove the grass collection box (10).  
u Empty the contents from the front of the box.  
u Place the grass collection box on the ground and pull in  
and hold the grass compaction lever release button (30).  
u Lift the grass compaction lever (29) into the vertical  
position and release the grass compaction lever release  
button (30).  
u Repeat the above procedure as required.  
u Empty the contents from the rear of the box.  
Warning: Do not work towards the cable as shown in fig. P2.  
Emptying the grass collection box (EMax34s only)  
When the grass collection box is full you should empty the  
grass in the collection box.  
u Release the on/off switch (2).  
u Remove the grass collection box (10).  
u Empty the contents from the box.  
Mowing (fig. P1 & P2) (EMax34s & EMax34i only)  
We recommend to use your mower as outlined in this section  
in order to achieve optimum results and to reduce the risk of  
cutting the mains cable.  
u Place the bulk of the mains cable on the lawn, close to the  
starting point (position 1 in fig. P1).  
3
(Original instructions)  
ENGLISH  
Cable storage (fig. O)  
The cable holders (6) provide a safe and convenient way to  
Technical data  
EMax34s  
EMax34i  
Type 3  
EMax38i  
EMax42i  
store the cable (31) when not in use.  
u Wrap the cable around the cable holders (6) in a figure of  
eight pattern.  
Type 3  
Type 3  
VAC  
W
230-240  
230-240  
230-240  
Voltage  
Power Input  
No-Load Speed  
Height adjustment  
Blade length  
Weight  
Carrying the mower  
Warning! Ensure the blade has completely stopped and  
disconnect the appliance from the mains.  
u The mower can be carried using the convenient carry  
handles (12).  
1400  
3500  
20-70  
340  
1600  
3500  
20-70  
380  
1800  
3500  
20-70  
420  
min-1  
mm  
mm  
kg  
Hints for optimum use  
u If the grass is longer than approximately 10 cm, make two  
cuts to obtain a better finish. First mow at maximum height  
of cut, then use a low or medium height of cut.  
12.1  
13.3  
13.9  
u In order to achieve optimum results, only mow dry grass.  
Hand/arm weighted vibration value according to EN 60335:  
= 3.2 m/s2 , uncertainty (K) = 1.5 m/s2.  
Troubleshooting  
If your appliance seems not to operate properly, follow the  
instructions below. If this does not solve the problem, please  
contact your local Black & Decker repair agent.  
Warning! Before proceeding, remove the plug from the  
socket.  
Problem  
Possible Cause  
Power turned off  
Fuse faulty/blown  
Grass too long  
Possible solution  
Turn power on  
Replace fuse  
Machine fails to  
operate  
Increase the height of  
cut and move machine  
to shorter grass to start  
Thermal cut out  
activated  
Allow motor to cool and  
increase height of cut  
Thermal cut out  
activated  
Allow motor to cool and  
increase height of cut  
Machine functions  
intermittently  
Machine leaves  
ragged finish or  
motor labours  
Height of cut too low  
Cutting blade blunt  
Increase height of cut  
Replace the blade  
Underside of machine  
clogged  
Check underneath the  
machine and clear out  
as necessary (always  
wear heavy duty  
gloves)  
Blade fitted upside  
down  
Refit blade correctly  
4
(Original instructions)  
ENGLISH  
EC declaration of conformity  
MACHINERY DIRECTIVE  
OUTDOOR NOISE DIRECTIVE  
%
EMax34s / EMax34i / EMax38i / EMax42i  
Black & Decker declares that these products described under  
"technical data" are in compliance with:  
2006/42/EC, EN 60335-1, EN 60335-2-77  
2000/14/EC, Lawn Mower, L < 50cm, Annex VI,  
Netherlands  
Level of sound power according to 2000/14/EC  
(Article 12, Annex III, L ≤ 50 cm):  
LWA (measured sound power) 93 dB(A)  
uncertainty (K) = 3 dB(A)  
LWA (guaranteed sound power) 96 dB(A)  
uncertainty (K) = 3 dB(A)  
These products also comply with directive  
2004/108/EC and 2011/65/EU.  
For more information, please contact Black & Decker at the  
following address or refer to the back of the manual.  
The undersigned is responsible for compilation of the technical  
_
Kevin Hewitt  
Vice-President Global Engineering  
Black & Decker Europe, 210 Bath Road, Slough,  
Berkshire, SL1 3YD  
United Kingdom  
04/12/2012  
5
ENGLISH  
Do not forget to register your product!  
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product  
code to Black & Decker in your country.  
Australia  
Black & Decker (Australia) Pty. Ltd.  
20 Fletcher Road, Mooroolbark,  
Victoria, 3138  
Tel. 03-8720 5100  
Fax 03-9727 5940  
New Zealand  
Black & Decker  
5 Te Apunga Place  
Mt Wellington  
Tel. +64 9 259 1133  
Fax +64 9 259 1122  
Auckland 1060  
United Kingdom  
Black & Decker  
210 Bath Road  
Tel. 01753 511234  
Fax 01753 551155  
Slough, Berkshire SL1 3YD  
90593758 REV-0  
12/2012  

Studer Innotec Xpc 2200 48 User Manual
Soleus Air Air Conditioner Pe8 12r 32 User Manual
Sharp Al 1555 User Manual
Sanyo Xs4232 User Manual
Philips Scb1440nb User Manual
Motorola H550 User Manual
Mitsubishi Electronics Peh 3ek User Manual
LG 47LB6350 User Manual
DELL WYSE 3020 02 User Manual
CANON SD780 IS User Manual