BLACK DECKER DV1815EL User Manual

DV7215EL  
DV1015EL  
DV1415EL  
DV1815EL  
G
H
I
J
3
(Original instructions)  
ENGLISH  
Intended use  
u
Never pull the charger lead to discon-  
nect the charger from the socket. Keep  
the charger lead away from heat, oil  
and sharp edges.  
Your Black & Decker Dustbuster® handheld vacuum cleaner  
has been designed for light dry vacuum cleaning purposes.  
This appliance is intended for household use only.  
Safety instructions  
u
This appliance can be used by chil-  
dren aged from 8 years and above  
and persons with reduced physical,  
sensory or mental capabilities or  
lack of experience and knowledge if  
they have been given supervision or  
instruction concerning use of the appli-  
ance in a safe way and understand the  
hazards involved. Children shall not  
play with the appliance. Cleaning and  
user maintenance shall not be made  
by children without supervision.  
Warning! Read all safety  
@
warnings and all in-  
structions. Failure to follow  
the warnings and instructions  
listed below may result in electric  
shock, fire and/or serious injury.  
Warning!When using battery-  
powered appliances, basic safety  
precautions, including the follow-  
ing, should always be followed to  
reduce the risk of fire, leaking bat-  
teries, personal injury and material  
damage.  
@
InBsepfoercetuisoen, cahencdk threepapapilriasnce for  
u
u
u
Read all of this manual carefully be-  
fore using the appliance.  
damaged or defective parts. Check for  
breakage of parts, damage to switches  
and any other conditions that may af-  
fect its operation.  
The intended use is described in this  
manual. The use of any accessory  
or attachment or the performance  
of any operation with this appliance  
other than those recommended in this  
instruction manual may present a risk  
of personal injury.  
u
u
Do not use the appliance if any part is  
damaged or defective.  
Have any damaged or defective parts  
repaired or replaced by an authorized  
repair agent.  
u
Retain this manual for future refer-  
ence.  
u
u
Regularly check the charger lead for  
damage. Replace the charger if the  
lead is damaged or defective.  
Never attempt to remove or replace  
any parts other than those specified in  
this manual.  
Using your appliance  
u
Do not use the appliance to pick up  
liquids or any materials that could  
catch fire.  
u
u
Do not use the appliance near water.  
Do not immerse the appliance in  
water.  
4
(Original instructions)  
ENGLISH  
Warning! The battery fluid may cause personal injury or  
damage to property. In case of skin contact, immediately rinse  
with water. If redness, pain or irritation occurs seek medical  
attention. In case of eye contact, rinse immediately with clean  
water and seek medical attention.  
Additional safety instructions  
After use  
u Unplug the charger before cleaning the charger.  
u When not in use, the appliance should be stored in a dry  
place.  
Chargers  
u Children should not have access to stored appliances.  
Your charger has been designed for a specific voltage. Always  
check that the mains voltage corresponds to the voltage on  
the rating plate.  
Warning! Never attempt to replace the charger unit with a  
regular mains plug.  
u Use your Black & Decker charger only to charge the bat-  
tery in the appliance/tool with which it was supplied. Other  
batteries could burst, causing personal injury and damage.  
u Never attempt to charge nonrechargeable batteries.  
u If the supply cord is damaged, it must be replaced by the  
manufacturer or an authorised Black & Decker Service  
Centre in order to avoid a hazard.  
Residual risks.  
Additional residual risks may arise when using the tool which  
may not be included in the enclosed safety warnings. These  
risks can arise from misuse, prolonged use etc.  
Even with the application of the relevant safety regulations  
and the implementation of safety devices, certain residual  
risks can not be avoided. These include:  
u Injuries caused by touching any rotating/moving parts.  
u Injuries caused when changing any parts, blades or ac-  
cessories.  
u Injuries caused by prolonged use of a tool. When using  
any tool for prolonged periods ensure you take regular  
breaks.  
u Do not expose the charger to water.  
u Do not open the charger.  
u Do not probe the charger.  
u Impairment of hearing.  
u The appliance/tool/battery must be placed in a well venti-  
lated area when charging.  
u Health hazards caused by breathing dust developed when  
using your tool (example:- working with wood, especially  
oak, beech and MDF.)  
Electrical safety  
Your charger has been designed for a specific voltage. Always  
check that the mains voltage corresponds to the voltage on  
the rating plate. Never attempt to replace the charger unit with  
a regular mains plug.  
Batteries and chargers  
Batteries  
u Never attempt to open for any reason.  
u Do not expose the battery to water.  
u Do not expose the battery to heat.  
Symbols on the charger  
u Do not store in locations where the temperature may  
exceed 40°C.  
u Charge only at ambient temperatures between 10°C and  
40°C.  
This tool is double insulated; therefore no earth wire  
is required. Always check that the power supply  
corresponds to the voltage on the rating plate.  
#
u Charge only using the charger provided with the appli-  
ance/tool. Using the wrong charger could result in an  
electric shock or overheating of the battery.  
u When disposing of batteries, follow the instructions given  
in the section "Protecting the environment".  
u Do not damage/deform the battery pack either by puncture  
or impact, as this may create a risk of injury and fire.  
u Do not charge damaged batteries.  
u Under extreme conditions, battery leakage may occur.  
When you notice liquid on the batteries carefully wipe the  
liquid off using a cloth. Avoid skin contact.  
u In case of skin or eye contact, follow the instructions  
below.  
Short circuit proof safety isolating transformer. The  
mains supply is electrically separated from the  
transformer output.  
The charging base is intended for indoor use only.  
$
5
(Original instructions)  
ENGLISH  
Use  
Features  
u Before first use, the battery must be charged for at least 4  
This tool includes some or all of the following features.  
1. On/off switch  
hours.  
2. Bowl release button  
3. Charging indicator  
4. Dust bowl  
5. Dust collector  
6. Charger socket  
Charging the battery (Fig. D)  
u Make sure that the appliance is switched off. The battery  
will not be charged with the on/off switch in the on posi-  
tion.  
u Plug the jack plug of the charger (7) into the charging  
socket (6) of the appliance.)  
7. Charger  
u Plug in the charger. Switch on at the mains. The charging  
indicator (3) will be lit.  
Assembly  
u Leave the appliance to charge for at least 4 hours.  
While charging, the charger may become warm. This is  
normal and does not indicate a problem. The appliance can  
be left connected to the charger indefinitely. The charging  
indicator (3) will be lit as long as the appliance is connected to  
the plugged-in charger.  
Accessories (fig. A & B)  
These models may be supplied with some of the following  
accessories:  
u An Integrated brush tool (9) for furniture and stairs.  
u An Integrated crevice tool (10) for confined spaces.  
Warning! Do not charge the battery at ambient temperatures  
below 10 °C or above 40 °C.  
The integrated brush tool (Fig. A)  
u Flip down the brush tool (9) at the end of the dust collec-  
tor.  
Switching on and off (fig. E)  
u To switch the appliance on, slide the on/off switch (1)  
forward to position 1.  
u To switch the appliance off, slide the on/off switch (1) back  
to position 0.  
The integrated crevice tool (Fig. B)  
u Extend the crevice tool (10) by pulling the crevice tool (10)  
until it locks into position.  
u Retract the crevice tool (10) by pressing the area (11) and  
pushing the crevice tool (10) back into the dust collector  
(5).  
Rotating the dust collector (fig. F)  
The nozzle can be rotated for better access in tight spots.  
u Press the rotation release catch (12).  
u Rotate the nozzle to the left or right until it clicks into  
place.  
Installation  
Wall Mounting (fig. C)  
The product can be attached to a wall to provide a convenient  
storage and charging point for the appliance.  
When fixing to a wall, make sure that the fixing method is  
suitable for the wall type and is appropriate to the weight of  
the appliance.  
Optimising the suction force  
In order to keep the suction force optimised, the filters must be  
cleared regularly during use.  
Emptying and cleaning the product  
u Mark the location of the screw holes (within reach of an  
electrical outlet for chargeing the vac while it is on the wall  
bracket).  
u Insert the charger cord into the curved slot in the wall  
mount bracket leaving approximately 8-9 inches excess.  
u Hang the appliance on the wall by placing the opening  
on the base of the vac over the hooks in the wall mount  
bracket.  
Emptying the dust bowl (fig. G)  
u Press the release latch (13) and pull the dust collector (5)  
straight off.  
u Empty the contents of the bowl.  
u To replace the dust collector, place it back onto the handle  
until it “clicks” firmly into position.  
6
(Original instructions)  
ENGLISH  
Removing the dust bowl and filters (fig. H & I)  
Warning! The filters are re-usable and should be cleaned  
regularly.  
u Press the release latch (2) and pull the dust bowl (4)  
straight off.  
Protecting the environment  
Separate collection. This product must not be  
disposed of with normal household waste.  
Z
u While holding the dust bowl over a bin or sink, pull out the  
filter (14) to empty the contents of the bowl.  
u To replace the dust bowl, place it back onto the handle  
until it “clicks” firmly into position.  
Should you find one day that your Black & Decker product  
needs replacement, or if it is of no further use to you, do not  
dispose of it with household waste. Make this product avail-  
able for separate collection.  
Warning! Never use the appliance without the filters. Opti-  
mum dust collection will only be achieved with clean filters.  
Separate collection of used products and packaging  
z
allows materials to be recycled and used again.  
Re-use of recycled materials helps prevent environ-  
mental pollution and reduces the demand for raw  
materials.  
Pre-filter (fig. J)  
The Filter and pre-filter can be separated to allow better  
cleaning.  
u Twist the pre-filter (16) in a clockwise direction and lift  
from the filter (15).  
Local regulations may provide for separate collection of elec-  
trical products from the household, at municipal waste sites or  
by the retailer when you purchase a new product.  
Cleaning the dust bowls and filters  
u The dust bowls and filters can be washed in warm soapy  
water.  
Black & Decker provides a facility for the collection and  
recycling of Black & Decker products once they have reached  
the end of their working life. To take advantage of this service  
please return your product to any authorised repair agent who  
will collect them on our behalf.  
u Make sure that the filters and the dust bowl are dry before  
re-fitting.  
Replacing the filters  
The filters should be replaced every 6 to 9 months and when-  
ever worn or damaged.  
Replacement filters are available from your Black & Decker  
dealer:  
For models: DV7215EL, DV1015EL, DV1415EL and  
DV1815EL use filter part number VF110-XJ  
You can check the location of your nearest authorised repair  
agent by contacting your local Black & Decker office at  
the address indicated in this manual. Alternatively, a list of  
authorised Black & Decker repair agents and full details of our  
after-sales service and contacts are available on the Internet  
Maintenance  
Your Black & Decker corded/cordless appliance/tool has been  
designed to operate over a long period of time with a minimum  
of maintenance. Continuous satisfactory operation depends  
upon proper tool care and regular cleaning.  
Battery  
If you want to dispose of the product yourself, the  
battery must be removed as described below and  
disposed of in accordance with local regulations.  
Z
Warning! Before performing any maintenance on corded/  
cordless power tools:  
u Switch off and unplug the appliance/tool.  
u Preferably discharge the battery by operating the appli-  
ance until the motor stops.  
u Or switch off and remove the battery from the appliance/  
tool if the appliance/tool has a separate battery pack.  
u Or run the battery down completely if it is integral and then  
switch off.  
u Unplug the charger before cleaning it. Your charger does  
not require any maintenance apart from regular cleaning.  
u Regularly clean the ventilation slots in your appliance/tool/  
charger using a soft brush or dry cloth.  
u Press the release button (2) and remove the dust bowl (4).  
u Remove the seven screws holding the body of the appli-  
ance together.  
u Lift the housing cover away from the assembly.  
u Detach all lead connections from the battery pack.  
u Remove battery pack.  
u Place the battery in a suitable packaging to ensure that  
the terminals cannot be short-circuited.  
u Regularly clean the motor housing using a damp cloth. Do  
not use any abrasive or solvent-based cleaner.  
u Take the battery to your service agent or to a local recy-  
cling station.  
Once removed, the battery cannot be refitted.  
7
(Original instructions)  
ENGLISH  
Technical data  
Guarantee  
Black & Decker is confident of the quality of its products and  
offers an outstanding guarantee. This guarantee statement is  
in addition to and in no way prejudices your statutory rights.  
The guarantee is valid within the territories of the Member  
States of the European Union and the European Free Trade  
Area.  
DV7215EL  
DV1015EL  
(H1)  
(H1)  
Voltage  
Battery  
Weight  
Charger  
Vdc  
7.2  
10.8  
Li-Ion  
1.18  
Type  
kg  
Li-Ion  
1.10  
If a Black & Decker product becomes defective due to faulty  
materials, workmanship or lack of conformity, within 24  
months from the date of purchase, Black & Decker guarantees  
to replace defective parts, repair products subjected to fair  
wear and tear or replace such products to ensure minimum  
inconvenience to the customer unless:  
u The product has been used for trade, professional or hire  
purposes;  
u The product has been subjected to misuse or neglect;  
u The product has sustained damage through foreign  
objects, substances or accidents;  
S010QV1400040  
S010QB1400040  
S010QV1400040  
S010QB1400040  
Input voltage  
Output voltage  
Current  
Vac  
Vdc  
mA  
h
100-240  
100-240  
14  
400  
4
14  
400  
4
Approximate  
charge time  
u Repairs have been attempted by persons other than  
authorised repair agents or Black & Decker service staff.  
Weight  
kg  
0.08  
0.08  
To claim on the guarantee, you will need to submit proof of  
purchase to the seller or an authorised repair agent. You can  
check the location of your nearest authorised repair agent  
by contacting your local Black & Decker office at the address  
indicated in this manual. Alternatively, a list of authorised  
Black & Decker repair agents and full details of our after-  
sales service and contacts are available on the Internet at:  
DV1415EL  
DV1815EL  
(H1)  
(H1)  
Voltage  
Battery  
Weight  
Charger  
Vdc  
14.4  
Li-Ion  
1.23  
18  
Type  
kg  
Li-Ion  
1.3  
S010QV2300040  
S010QB2300040  
S010QV2300040  
S010QB2300040  
your new Black & Decker product and to be kept up to date  
on new products and special offers. Further information on the  
Black & Decker brand and our range of products is available  
Input voltage  
Output voltage  
Current  
Vac  
Vdc  
mA  
h
100-240  
100-240  
23  
400  
4
23  
400  
4
Approximate  
charge time  
Weight  
kg  
0.08  
0.08  
8
(Original instructions)  
ENGLISH  
9
10  
ENGLISH  
Do not forget to register your product!  
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product  
code to Black & Decker in your country.  
Australia  
Black & Decker (Australia) Pty. Ltd.  
20 Fletcher Road, Mooroolbark,  
Victoria, 3138  
Tel. 03-8720 5100  
Fax 03-9727 5940  
New Zealand  
Black & Decker  
5 Te Apunga Place  
Mt Wellington  
Tel. +64 9 259 1133  
Fax +64 9 259 1122  
Auckland 1060  
United Kingdom  
Black & Decker  
210 Bath Road  
Tel. 01753 511234  
Fax 01753 512365  
Slough, Berkshire SL1 3YD  
90611512 REV-0  
05/2014  

Soleus Air Sg Wac 25ese C User Manual
Sanyo Ks3632 User Manual
Ricoh Aficio Mp C3300 User Manual
Panasonic Kx Pw308dw User Manual
HITACHI CABLE WIRELESSIP 5000 User Manual
EPSON DS 510 User Manual
EMERSON RP6247 User Manual
CRAFTSMAN 580.325610 User Manual
ATLAS SOUND MPA1202 User Manual
ASUS ZEN AIO PRO Z220IC User Manual