Contents
Notices.......................................................................................................... iv
Safety.information........................................................................................ v
Care.&.Cleaning........................................................................................... vi
Takeback.Services..................................................................................... vii
iii
Notices
Federal.Communications.Commission.Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Canadian.Department.of.Communications.Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian Interference
- Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement
sur le matériel brouiller du Canada.
iv
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
•
•
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
•
Use the appropriate power plug which complies with your local power standard.
Do not overload power strips and extention cords. Overloading can result in fire
or electric shock.
•
•
•
•
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240V AC.
•
•
If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer.
Adjustment of the volume control as well as the equalizer to other settings
than the center position may increase the ear-/headphones output voltage and
therefore the sound pressure level.
•
The adapter is only used for this monitor, do not use it for other purpose.
Your device uses one of the following power supplies:
- Manufacturer: Delta Electronics Inc., Model: ADP-65GD B/ADP-65GD D.
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
v
AEEE.yönetmeliğine.uygundur
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The.following.symptoms.are.normal.with.the.monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions.used.in.this.guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where.to.find.more.information
Refer to the following sources for additional information and for product and
software updates.
1.. ASUS.websites
The ASUS websites worldwide provide updated information on ASUS
2.. Optional.documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
information in different region.
vii
viii
1.1
Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a broader, brighter and
crystal-clear display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2
Package contents
Check your package for the following items:
LCD monitor
Monitor base
Quick start guide
Warranty card
Power adapter
Power cord
DisplayPort cable (optional)
HDMI cable (optional)
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS VG27 Series LCD Monitor
1-1
1.3 Monitor introduction
1.3.1.
Front.view
1
2
3
4
5
1.
2.
(
5-way) button:
• Turns on the OSD menu. Enacts the selected OSD menu item.
• Increases/Decreases values or moves your selection up/down/left/right.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
button
• Exits the OSD menu item.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
• Toggles the Key Lock function between on and off with a long press for 5
seconds.
3.
4.
button:
• GamePlus hotkey. Move the
(
) button up/down to select and
press ) to confirm the function needed.
(
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
button
• GameVisual hotkey. This function contains 7 sub-functions you can
select for your preference.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
1-2
Chapter 1: Product introduction
5.
Power button/power indicator
• Turns the monitor on/off.
• The color definition of the power indicator is as the below table.
Status
Description
White
Amber
OFF
ON
Standby mode/No signal
OFF
1.3.2.
Back.view
7
4
5
6
1.. HDMI.port. This port is for connection with an HDMI compatible device.
2.. HDMI.port. This port is for connection with an HDMI compatible device.
3.. DisplayPort.in. This port is for connection with a DisplayPort compatible
device.
4.. Earphone.jack. This port is only available when an HDMI/DisplayPort cable
is connected.
5.. DC-IN.port. This port connects the power cord.
6.. Kensington.lock.slot.
7.. Control.buttons.
1.3.3.
GamePlus.Function
The GamePlus function provides a toolkit and creates a better gaming environment
for users when playing different types of games. The crosshair overlay with 6
different crosshair options lets you choose the one that best suits the game you're
playing. There's also an onscreen timer you can position on the left of the display
so you can keep track of the elapsed gaming time; while the FPS (frames per
second) counter lets you know how smooth the game is running. Display Alignment
displays alignment lines on 4 sides of the screen, serving as an easy and handy
tool for you to line up multiple monitors perfectly. Sniper function (only available
when HDR is disabled on your device) is customized for first-person shooters. You
can select the magnification ratio and the type of alignment in sequence.
ASUS VG27 Series LCD Monitor
1-3
To active GamePlus:
1.
Press the GamePlus hotkey.
2.
3.
Move the
Press the
(
) button up/down to select among different functions.
) button or move the ) button right to confirm the
) button up/down to navigate
) button left to go back, off, and exit.
(
(
function you choose, and move the
through the settings. Move the
(
(
4.
Highlight the desired setting and press the
Press the button to inactivate it.
(
) button to activate it.
GamePlus Main Menu
GamePlus — Crosshair
GamePlus
GamePlus
Crosshair
(Practice Mode)
Timer
FPS
FPS Counter
Display Alignment
Sniper
(Practice Mode)
NEXT
BACK/EXIT
NEXT
BACK/EXIT
GamePlus — Timer
GamePlus — Sniper
GamePlus
GamePlus
1.5x
1.7x
2.0x
NEXT
BACK/EXIT
NEXT
BACK/EXIT
1-4
Chapter 1: Product introduction
1.3.4.
GameVisual.Function
The GameVisual function helps you select among different picture modes in a
convenient way.
To active GameVisual:
Press the GameVisual hotkey repeatedly to select.
•. Scenery.Mode: This is the best choice for scenery photo displaying with
GameVisualTM Video intelligence Technology.
•. Racing.Mode: This is the best choice for racing game playing with
GameVisualTM Video intelligence Technology.
•. Cinema.Mode: This is the best choice for movie watching with
GameVisualTM Video intelligence Technology.
•. RTS/RPG.Mode: This is the best choice for Real-Time Strategy (RTS)/
Role-Playing Game (RPG) playing with GameVisualTM Video intelligence
Technology.
•. FPS.Mode: This is the best choice for First Person Shooter game playing
with GameVisualTM Video intelligence Technology.
•. sRGB.Mode: This is the best choice for viewing photos and graphics
from PCs.
•. MOBA.Mode: This is the best choice for multiplayer online battle arena
game playing with GameVisualTM Video intelligence Technology.
•
•
In the Racing mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, Sharpness, ASCR.
In the sRGB mode, the following function(s) are not user-configurable:
Brightness, Contrast, Saturation, Color Temp., Skin Tone, Sharpness,
ASCR.
•
In the MOBA mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, Sharpness, ASCR.
ASUS VG27 Series LCD Monitor
1-5
1-6
Chapter 1: Product introduction
2.1
Assembling the monitor arm/base
To assemble the monitor base:
1.
2.
Have the front of the monitor face down on a table.
Attach the base into the arm, making sure the tab on the arm fits into the groove
on the base.
3.
Fix the base to the arm by fastening the bundled screw.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
ASUS VG27 Series LCD Monitor
2-1
2.2
Adjusting the monitor
•
For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
•
•
Hold the stand to prevent the monitor from falling when you change its angle.
The recommended adjusting angle is +33˚ to -5˚ (for tilt)/+90˚ to -90˚ (for
swiveling/ +130 mm (for height adjustment)/90˚ (for portrait view).
-5°~+33°
130mm
90°
90°
0°
(Tilt)
(Swivel)
(Height adjustment)
It is normal that the monitor slightly shakes while you adjust the viewing angle.
Pivoting.the.monitor
1.
2.
3.
Lift the monitor to the highest position.
Tilt the monitor to its maximum angle.
Pivot the monitor to the angle you need.
0°
-5°~+33°
-90°
0°
90°
It is normal that the monitor slightly shakes while you adjust the viewing angle.
2-2
Chapter 2: Setup
2.3
Detaching the arm (for VESA wall
mount)
The detachable arm/base of this monitor is specially designed for VESA wall
mount.
To detach the arm/base:
1.
2.
Have the front of the monitor face down on a table.
Loosen the four screws on the back of the monitor and remove the arm/base.
2
1
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2.4
Connecting the cables
Connect the cables as the following instructions:
•. To.connect.the.power.cord:
a. Connect the power adapter securely to the monitor’s DC input.
b. Connect one end of the power cord to the power adapter and the other
end to a power outlet.
ASUS VG27 Series LCD Monitor
2-3
•. To.connect.the.DisplayPort/HDMI.cable:
a. Plug one end of the DisplayPort/HDMI cable to the monitor’s
DisplayPort/HDMI port.
b. Connect the other end of the DisplayPort/HDMI cable to your computer's
DisplayPort/HDMI port.
•. To.use.the.earphone: connect the end with plug type to the monitor’s
earphone jack when an HDMI or DisplayPort signal is fed.
2.5
Turning on the monitor
Press the power button
. See page 1-2 for the location of the power button. The
power indicator lights up in white to show that the monitor is ON.
2-4
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1.
How.to.reconfigure
ASUS TUF Gaming VG27B HDR Off
Racing Mode DispalyPort 2560x1440@ 155Hz
GameVisual
Scenery Mode
Racing Mode
Cinema Mode
RTS/RPG Mode
FPS Mode
sRGB Mode
MOBA Mode
1.
2.
Press the
Move the
(
) button to activate the OSD menu.
(
) button up/down to navigate through the functions.
Highlight the desired function and press the
(
) button to activate it. If
) button up/down
the function selected has a sub-menu, move the
(
again to navigate through the sub-menu functions. Highlight the desired sub-
menu function and press the
right to activate it.
(
) button or move the
(
) button
3.
4.
Move the
function.
(
) button up/down to change the settings of the selected
To exit and save the OSD menu, press the
button or move the
(
) left repeatedly until the OSD menu disappears. To adjust other
functions, repeat steps 1-3.
3.1.2.
OSD.function.introduction
1.. GameVisual
ASUS TUF Gaming VG27B HDR Off
Racing Mode DispalyPort 2560x1440@ 155Hz
GameVisual
Scenery Mode
Racing Mode
Cinema Mode
RTS/RPG Mode
FPS Mode
sRGB Mode
MOBA Mode
Please refer to “1.3.4
GameVisual Function”.
ASUS VG27 Series LCD Monitor
3-1
2.. Blue.Light.Filter
In this function, you can adjust the blue light filter level.
ASUS TUF Gaming VG27B HDR Off
Racing Mode DispalyPort 2560x1440@ 155Hz
Blue Light Filter
Level
Level
Level
Level
Level
0
1
2
3
4
•.
•.
Level.0:.No change.
Level.1~4: The higher the level, the less blue light is scattered.
When Blue Light Filter is activated,the default settings of Racing Mode
will be automatically imported. Between Level 1 to Level 3, the Brightness
function is user-configurable. Level 4 is optimized setting. It is compliance
with TUV Low Blue Light Certification. The Brightness function is not user-
configurable.
Please refer to the following to alleviate eye strains:
•
Users should take some time away from the display if working for long
hours. It is advised to take short breaks (at least 5 mins) after around 1
hour of continuous working at the computer. Taking short and frequent
breaks is more effective than a single longer break.
•
•
To minimize eye strain and dryness in your eyes, users should rest the eye
periodically by focusing on objects that are far away.
Eye exercises can help to reduces eye strain. Repeat these exercises
often. If eye strain continues please consult a physician. Eye exercises: (1)
Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes
diagonal.
•
High energy blue light may lead to eye strain and AMD (Age-Related
Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful blue
light to avoiding CVS (Computer Vision Syndrome).
3-2
Chapter 3: General Instructions
3.. Color
Set a desired color setting from this menu.
ASUS TUF Gaming VG27B HDR Off
Racing Mode DispalyPort 2560x1440@ 155Hz
Color
Brightness
Contrast
Saturation
Color Temp.
Skin Tone
Smart View
•.
•.
•.
•.
Brightness: The adjusting range is from 0 to 100.
Contrast: The adjusting range is from 0 to 100.
Saturation: the adjusting range is from 0 to 100.
Color.Temp.: Contains 4 modes including Cool, Normal, Warm, and User
Mode.
•.
•.
Skin.Tone: Contains three color modes including Reddish, Natural, and
Yellowish.
Smart.View.(only.for.VG27B.series): Provides better display quality
under big viewing angle.
4.. Image.
Set the image related setting from this menu.
ASUS TUF Gaming VG27B HDR Off
Racing Mode DispalyPort 2560x1440@ 155Hz
Image
HDR
Over Clocking
Sharpness
VividPixel
Adaptive-Sync
ELMB SYNC
Shadow Boost
More
•.
•.
HDR: Contains two HDR modes.
*.
ASUS.Gaming.HDR: Is the HDR mode that ASUS has specially
adjusted for HDR performance.
*.
ASUS.Cinema.HDR: Complies with VESA Display HDR.
Over.Clocking.(DisplayPort.only): Allows you to adjust the refresh rate.
Select “ON“ if you want to enable this function.
ASUS VG27 Series LCD Monitor
3-3
Over Clocking may cause screen flickering. To reduce such effects,
disconnect the DisplayPort cable and use the monitor OSD menu to try
again with a safer Max. Refresh rate.
•
•
•
Sharpness: The adjusting range is from 0 to 100.
Trace Free: Adjusts the response time of the monitor.
Aspect Control: Adjusts the aspect ratio to full or 4:3.
4:3 is only available when input source is in 4:3 format.
•
VividPixel: Enhances the outline of the displayed picture and generates
high-quality images on screen.
•
•
ASCR: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
Adaptive-Sync (DisplayPort/HDMI only) Allows an Adaptive-Sync
:
supported* graphics source to dynamically adjust display refresh rate
based on typical content frame rates for power efficient, virtually stutter
free and low-latency display update.
* Adaptive-Sync can only be activated within 48Hz ~ 155Hz (DisplayPort
only) and 48Hz ~ 144Hz (HDMI only).
* For supported GPUs, minimum PC system and driver requirements,
please contact the GPU manufactures.
•
•
ELMB SYNC: Allows you to turn on the function when Adaptive-Sync is
On. This function eliminates screen tearing, reduces ghosting and motion
blur when playing games.
When Adaptive-Sync is Off, this function can only be activated when the
refresh rate is 100Hz, 120Hz, 144Hz or 155Hz.
Shadow Boost: Dark color enhancement adjusts monitor gamma curve
to enrich the dark tones in an image, making dark scenes and objects
much easier to be seen.
This function is only available in Racing mode, RTS/RPG mode, FPS
mode or sRGB mode.
3-4
Chapter 3: General Instructions
5.. Sound
Set the sound related setting from this menu.
ASUS TUF Gaming VG27B HDR Off
Racing Mode DispalyPort 2560x1440@ 155Hz
Sound
Volume
Mute
•.
•.
Volume: The adjusting range is from 0 to 100.
Mute: Toggles the monitor sound between on and off.
6.. Input.Select.
In this function, you can select your desired input source.
ASUS TUF Gaming VG27B HDR Off
Input Select
Racing Mode DispalyPort 2560x1440@ 155Hz
HDMI-1
HDMI-2
DisplayPort
7.. System.Setup.
Allows you to adjust the system.
ASUS TUF Gaming VG27B HDR Off
Racing Mode DispalyPort 2560x1440@ 155Hz
System Setup
GameVisual Demo Mode
ECO Mode
OSD Setup
Language
Key Lock
Information
Power Indicator
More
•.
•.
GameVisual.Demo.Mode: Activate the demo mode for the GameVisual
function.
ECO.Mode: reduces power consumption.
ASUS VG27 Series LCD Monitor
3-5
•.
OSD.Setup:
*
*
*
Adjusts the OSD timeout from 10 to 120 seconds.
Enables or disables the DDC/CI function.
Adjusts the OSD background from opaque to transparent.
•.
•.
Language: There are 21 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian.
Key.Lock: To disable all function keys. Press
over 5 seconds to
cancel the key lock function.
•.
•.
•.
•.
Information: Shows the monitor information.
Power.Indicator: Turn the power LED indicator on/off.
Power.Key.Lock: Enables or disables the power key.
All.Reset: “Yes” allows you to restore the default settings.
8.. MyFavorite
Loads/Saves all settings on the monitor.
ASUS TUF Gaming VG27B HDR Off
MyFavorite
Racing Mode DispalyPort 2560x1440@ 155Hz
Setting
Setting
Setting
1
2
3
3-6
Chapter 3: General Instructions
3.2
Specifications summary
Panel.Type
Panel.size
Max..Resolution
TFT LCD
27”W (16:9, 68.5 cm) wide screen
2560 x 1440
Pixel.pitch
0.233 mm
350 cd/m2
1000:1
Brightness.(Typ.)
Contrast.Ratio.(Typ.)
Viewing.angle(H/V).CR>10
VG27AQ: 178˚/178˚
VG27BQ: 170˚/160˚
Display.colors
Response.time
16.7 M
VG27AQ: 1ms MPRT
VG27BQ: 1 ms (Gray to gray), 0.4 ms (Gray to
gray, minimum)
Color.temperature.selection
Analog.input
Digital.input
4 color temperatures
No
HDMI x 2, DisplayPort v1.2 x 1
Earphone.jack
Audio.input
Yes
No
Speaker.(Built-in)
USB.3.0.port
Colors
2 W x 2 Stereo, RMS
No
Black
Power.LED
Tilt
White (On)/Amber (Standby)
+33˚~ -5˚
Swivel
+90˚~ -90˚
Height.adjustment
VESA.wall.mount
Kensington.lock
Voltage.rating
130 mm
100 x 100 mm
Yes
AC: 100~240V
DC: 19 V, 3.42 A (AC adapter)
Power.consumption
Power On: < 65 W, Standby: < 0.5 W,
Power Off: < 0.5 W
Temperature.(Operating)
0˚C~40˚C
Temperature.(Non-operating)
-20˚C~+60˚C
Dimensions. (W. x. H. x. D). without. 619 mm x 363 mm x 50 mm
stand
Dimensions.(W.x.H.x.D).with.stand 620 mm x 507 mm x 211 mm (highest)
620 mm x 378 mm x 211 mm (lowest)
704 mm x 464 mm x 210 mm (package)
Weight.(Esti.)
5.8 kg (Net); 3.5 kg (without stand); 8.0 kg
(Gross)
ASUS VG27 Series LCD Monitor
3-7
Multi-languages
21 languages (English, French, German,
Italian, Spanish, Dutch, Portuguese, Russian,
Czech, Croatian, Polish, Romanian, Hungarian,
Turkish, Simplified Chinese, Traditional Chinese,
Japanese, Korean, Thai, Indonesian, Persian)
Accessories.
DisplayPort cable (optional), HDMI cable
(optional), power adapter, power cord, Quick start
guide, warranty card
Compliance.and.Standards
UL/cUL, CB, CE, ErP, FCC, CCC, CU, RCM,
BSMI, VCCI, RoHS, J-MOSS, WEEE, Windows
7 & 8.1 & 10 WHQL, CEL, MEPS, PSE,
UkrSEPRO, KCC, E-Standby, TUV-Flicker Free,
TUV-Low Blue Light, ICES-3, PC Recycle
*Specifications.are.subject.to.change.without.notice.
3-8
Chapter 3: General Instructions
3.3
Outline dimensions
ASUS VG27 Series LCD Monitor
3-9
3.4
Troubleshooting (FAQ)
Problem
Possible.Solution
Power LED is not ON
•
•
Press the
is in the ON mode.
Check if the power cord is properly
connected to the monitor and the power
outlet.
button to check if the monitor
The power LED lights amber and there is
no screen image
•
•
•
•
Check if the monitor and the computer are
in the ON mode.
Make sure the signal cable is properly
connected the monitor and the computer.
Inspect the signal cable and make sure
none of the pins are bent.
Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
•
•
Adjust the Contrast and Brightness
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
Make sure the signal cable is properly
connected to the monitor and the
computer.
•
Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure
not look white)
that none of the pins are bent.
Perform All Reset via OSD.
Adjust the R/G/B color settings or select
the Color Temperature via OSD.
•
•
3-10
Chapter 3: General Instructions
3.5
Supported operating mode
Timing.List
HDMI.2.0
DisplayPort.1.2
640x480@60
640x480@67
640x480@72
640x480@75
720x400@70
800x600@56
800x600@60
800x600@72
800x600@75
832x624@75
1024x768@60
1024x768@70
1024x768@75
1152x864@75
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
X
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
X
X
V
V
V
V
V
1280x1024@60
1280x1024@75
1440x900@60
1920x1080@60
1920x1080@100
1920x1080@120
2560x1440@60
2560x1440@100
2560x1440@120
2560x1440@144
2560x1440@155
Video.Timing
Timing.List
HDMI.2.0
DisplayPort.1.2
720x480P@60
720x576P@50
1280x720P@50
1280x720P@60
V
V
V
V
V
V
V
X
X
V
V
V
V
V
ASUS VG27 Series LCD Monitor
3-11
Video.Timing
Timing.List
HDMI.2.0
DisplayPort.1.2
1440x480P@60
1440x576P@50
1920x1080P@30
1920x1080P@50
1920x1080P@60
1920x1080P@120
V
V
V
V
V
V
V
V
X
V
V
X
X
X
V
V
V
V
Note:.Do.not.support.interlace.
3-12
Chapter 3: General Instructions
|
