TUF Gaming Monitor
VG1A series
User Guide
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian Interference
- Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement
sur le matériel brouiller du Canada.
iv
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
•
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
•
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
•
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
Use the appropriate power plug which complies with your local power standard.
•
Do not overload power strips and extention cords. Overloading can result in fire
or electric shock.
•
•
•
•
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240V AC.
•
•
If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer.
Adjustment of the volume control as well as the equalizer to other settings
than the center position may increase the ear-/headphones output voltage and
therefore the sound pressure level.
•
The adapter is only used for this monitor, do not use it for other purpose.
Your device uses one of the following power supplies:
- Manufacturer: Delta Electronics Inc., Model: ADP-90YD B
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
v
AEEE yönetmeliğine uygundur
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
2.
Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
information in different region.
vii
1.1
Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a broader, brighter and
crystal-clear display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2
Package contents
Check your package for the following items:
LCD monitor
Monitor base
Quick start guide
Warranty card
Power adapter
Power cord
DisplayPort cable (optional)
HDMI cable (optional)
USB cable (optional)
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS TUF Gaming Monitor VG1A series
1-1
1.3 Monitor introduction
1.3.1
Front view
1
2
3
4
5
1.
2.
(
5-way) button:
• Turns on the OSD menu. Enacts the selected OSD menu item.
• Increases/Decreases values or moves your selection up/down/left/right.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
button
• Exits the OSD menu item.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
• Toggles the Key Lock function between on and off with a long press for 5
seconds.
3.
4.
Shortcut 1 button:
• Default: GamePlus.
• To change the shortcut function, go to the MyFavorite > Shortcut >
Shortcut 1 menu.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
Shortcut 2 button:
• Default: GameVisual.
1-2
Chapter 1: Product introduction
• To change the shortcut function, go to the MyFavorite > Shortcut >
Shortcut 2 menu.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
5.
Power button/power indicator
• Turns the monitor on/off.
• The color definition of the power indicator is as the below table.
Status
Description
White
Amber
OFF
ON
Standby mode/No signal
OFF
1.3.2
Back view
4
5
6
7
8
9
10
1.
2.
3.
4.
5.
DC-IN port. This port connects the power cord.
HDMI port. This port is for connection with an HDMI compatible device.
HDMI port. This port is for connection with an HDMI compatible device.
DisplayPort. This port is for connection for a DisplayPort compatible device.
Earphone jack. This port is only available when an HDMI/DisplayPort cable
is connected.
6.
This port is for service only. (USB Type-A)
7.
USB Type B. This port is for connection with a USB upstream cable. The
connection enables the USB ports on the monitor.
8.
USB Type A. These ports are for connection with USB devices, such as USB
keyboard/mouse, USB flash drive, etc.
9.
Kensington lock slot.
10. Control buttons.
ASUS TUF Gaming Monitor VG1A series
1-3
1.3.3
GamePlus Function
The GamePlus function provides a toolkit and creates a better gaming environment
for users when playing different types of games. The crosshair overlay with 6
different crosshair options letting you choose the one that best suits the game
you're playing. There's also an onscreen timer you can position on the left of the
display so you can keep track of the elapsed gaming time; while the FPS (frames
per second) counter lets you know how smooth the game is running. Display
Alignment displays alignment lines on 4 sides of the screen, serving as an easy
and handy tool for you to line up multiple monitors perfectly. Sniper function (only
available when HDR is disabled on your device) is customized for first-person
shooters. You can select the magnification ratio and the type of alignment in
sequence.
To active GamePlus:
1.
Press the GamePlus hotkey.
2.
3.
Move the
Press the
(
) button up/down to select among different functions.
) button or move the ) button right to confirm the
) button up/down to navigate
) button left to go back, off, and exit.
) button to activate it.
(
(
function you choose, and move the
through the settings. Move the
(
(
4.
Highlight the desired setting and press the
Press the button to inactivate it.
(
GamePlus
Main Menu
GamePlus —
Crosshair
GamePlus —
Timer
GamePlus —
FPS counter
GamePlus —
Sniper
GamePlus
GamePlus
GamePlus
GamePlus
ꢀꢁꢂePlꢃs
Crosshair
(Practice Mode)
FPS
Timer
FPS
FPS Counter
Display Alignment
Sniper
(Practice Mode)
1-4
Chapter 1: Product introduction
1.3.4
GameVisual Function
The GameVisual function helps you select among different picture modes in a
convenient way.
To active GameVisual:
Press the GameVisual hotkey repeatedly to select.
• Scenery Mode: This is the best choice for scenery photo displaying with
GameVisualTM Video intelligence Technology.
• Racing Mode: This is the best choice for racing game playing with
GameVisualTM Video intelligence Technology.
• Cinema Mode: This is the best choice for movie watching with
GameVisualTM Video intelligence Technology.
• RTS/RPG Mode: This is the best choice for Real-Time Strategy (RTS)/
Role-Playing Game (RPG) playing with GameVisualTM Video intelligence
Technology.
• FPS Mode: This is the best choice for First Person Shooter game playing
with GameVisualTM Video intelligence Technology.
• sRGB Mode: This is the best choice for viewing photos and graphics
from PCs.
• MOBA Mode: This is the best choice for multiplayer online battle arena
game playing with GameVisualTM Video intelligence Technology.
•
•
•
In the Racing mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, ASCR.
In the sRGB mode, the following function(s) are not user-configurable:
Brightness, Contrast, Saturation, Color Temp., Skin Tone, ASCR.
In the MOBA mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, ASCR.
ASUS TUF Gaming Monitor VG1A series
1-5
1-6
Chapter 1: Product introduction
2.1
Assembling the monitor arm/base
To assemble the monitor base:
1.
2.
Have the front of the monitor face down on a table.
Attach the base into the arm, making sure the tab on the arm fits into the groove
on the base.
3.
Fix the base to the arm by fastening the bundled screws.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
1
2
1
2
Base screw size: M6 x 16.2 mm.
ASUS TUF Gaming Monitor VG1A series
2-1
2.2
Adjusting the monitor
•
For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
•
•
Hold the stand to prevent the monitor from falling when you change its angle.
The recommended adjusting angle is +20˚ to -5˚ (for tilt)/+20˚ to -20˚ (for
swiveling/ +130 mm (for height adjustment)/90˚ (for portrait view).
-5°~ +20°
130mm
20°
20°
0°
(Tilt)
(Swivel)
(Height adjustment)
It is normal that the monitor slightly shakes while you adjust the viewing angle.
Pivoting the monitor
1.
2.
3.
Lift the monitor to the highest position.
Tilt the monitor to its maximum angle.
Pivot the monitor to the angle you need.
-5°~ +20°
0°
0°
90°
90°
It is normal that the monitor slightly shakes while you adjust the viewing angle.
2-2
Chapter 2: Setup
2.3
Detaching the arm (for VESA wall
mount)
The detachable arm/base of this monitor is specially designed for VESA wall
mount.
To detach the arm/base:
1.
2.
3.
4.
Have the front of the monitor face down on a table.
Remove the rubbers in the four screw holes. (Figure 1)
Remove the base (Figure 2).
Use a screwdriver to remove the screw on the hinge (Figure 3), then remove
the hinge.
1
1
2
2
(Figure 1)
(Figure 2)
(Figure 3)
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2.4
Cable management
You can organize the cables using the cable managment slot. Remove the cover
before putting the cables through the slot and attach the cover back on.
2
2
1
1
ASUS TUF Gaming Monitor VG1A series
2-3
2.5
Connecting the cables
Connect the cables as the following instructions:
For service only
•
•
To connect the power cord:
a. Connect the power adapter securely to the monitor’s DC input.
b. Connect one end of the power cord to the power adapter and the other
end to a power outlet.
To connect the DisplayPort/HDMI cable:
a. Plug one end of the DisplayPort/HDMI cable to the monitor’s
DisplayPort/HDMI port.
b. Connect the other end of the DisplayPort/HDMI cable to your computer's
DisplayPort/HDMI port.
•
•
To use the earphone: connect the end with plug type to the monitor’s
earphone jack when an HDMI or DisplayPort signal is fed.
To use the USB 3.0 ports: Take the supplied USB 3.0 cable, and plug
the smaller end (type B) of the USB upstream cable to the monitor’s USB
upstream port, and the larger end (type A) to your computer’s USB 3.0 port.
Make sure your computer is installed with the lastest Windows 7/Windows 8.1/
Windows 10 operating system. That will enable the USB ports on the monitor
to work.
When these cables are connected, you can choose the desired signal
from the Input Select item in the OSD menu.
2-4
Chapter 2: Setup
2.6
Turning on the monitor
Press the power button
. See page 1-2 for the location of the power button. The
power indicator lights up in white to show that the monitor is ON.
ASUS TUF Gaming Monitor VG1A series
2-5
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
ASUS TUꢀ ꢁꢂꢃiꢄg ꢅꢁ2ꢆAꢇꢈꢉA ꢊꢋR Oꢌꢌ
Gaming
Rꢂꢍiꢄg Mode ꢋisplꢂyPort 2ꢎꢏ0ꢐꢉꢑꢑ0ꢒ ꢏ0ꢊꢓ
Overclocking
OverDrive
Adaptive-Sync (DP)
ELMB SYNC
GamePlus
GameVisual
Shadow Boost
1.
2.
Press the
Move the
(
) button to activate the OSD menu.
(
) button up/down to navigate through the functions.
Highlight the desired function and press the
(
) button to activate it. If
) button up/down
the function selected has a sub-menu, move the
(
again to navigate through the sub-menu functions. Highlight the desired sub-
menu function and press the
right to activate it.
(
) button or move the
(
) button
3.
4.
Move the
function.
(
) button up/down to change the settings of the selected
To exit and save the OSD menu, press the
button or move the
(
) left repeatedly until the OSD menu disappears. To adjust other
functions, repeat steps 1-3.
3.1.2
OSD function introduction
1.
Gaming
ASUS TUꢀ ꢁꢂꢃiꢄg ꢅꢁ2ꢆAꢇꢈꢉA ꢊꢋR Oꢌꢌ
Gaming
Rꢂꢍiꢄg Mode ꢋisplꢂyPort 2ꢎꢏ0ꢐꢉꢑꢑ0ꢒ ꢏ0ꢊꢓ
Overclocking
OverDrive
Adaptive-Sync (DP)
ELMB SYNC
GamePlus
GameVisual
Shadow Boost
ASUS TUF Gaming Monitor VG1A series
3-1
•
Overclocking:
*
*
ON: This function allows you to adjust the refresh rate.
Max Refresh Rate: Allows you to select a maximum refresh rate
of 170Hz (Only for DisplayPort input). After selecting, press the
(
) button to activate the setting.
Overclocking may cause screen flickering. To reduce such effects, disconnect
the DisplayPort cable and use the monitor OSD menu to try again with a safer
Max. Refresh rate.
•
•
OverDrive: Improves the gray level response time of the LCD panel.
This function is not available when ELMB SYNC is enabled.
Adaptive-Sync (DP)/ Variable Refresh Rate: Allows an Adaptive-Sync
supported* graphics source to dynamically adjust display refresh rate
based on typical content frame rates for power efficient, virtually stutter
free and low-latency display update.
•
Adaptive-Sync (DP)/ Variable Refresh Rate can only be activated within
48Hz~144Hz for HDMI and 48Hz~170Hz for DisplayPort.
•
For supported GPUs, minimum PC system and driver requirements,
please contact the GPU manufactures.
•
ELMB SYNC: Allows you to turn on the function when Adaptive-Sync
(DP)/ Variable Refresh Rate is On. This function eliminates screen
tearing, reduces ghosting and motion blur when playing games.
When Adaptive-Sync (DP)/ Variable Refresh Rate is Off, this function can
only be activated when the refresh rate is 120Hz, 144Hz, 155Hz, 160Hz, 165Hz
or 170Hz.
•
•
•
Shadow Boost: Dark color enhancement adjusts monitor gamma curve
to enrich the dark tones in an image, making dark scenes and objects
much easier to be seen.
This function is only available in Racing mode, RTS/RPG mode, FPS mode, or
sRGB mode.
3-2
Chapter 3: General Instructions
2.
Image
ASUS TUꢀ ꢁꢂꢃiꢄg ꢅꢁ2ꢆAꢇꢈꢉA ꢊꢋR Oꢌꢌ
Image
Rꢂꢍiꢄg Mode ꢋisplꢂyPort 2ꢎꢏ0ꢐꢉꢑꢑ0ꢒ ꢏ0ꢊꢓ
Brightness
Contrast
HDR
Dynamic Dimming
VividPixel
ASCR
Aspect Control
Blue Light Filter
•
Brightness: The adjusting range is from 0 to 100.
This function is not available when ELMB SYNC is enabled.
•
•
Contrast: The adjusting range is from 0 to 100.
HDR: Contains two HDR modes.
*
ASUS Gaming HDR: Is the HDR mode that ASUS has specially
adjusted for HDR performance.
*
ASUS Cinema HDR: Complies with VESA Display HDR.
When detecting HDR content, an “HDR ON” message will pop up. When
displaying HDR content, the following function(s) are not available: ELMB Sync,
Sniper, GameVisual, Shadow Boost, Brightness, Contrast, ASCR, Aspect
Control, Blue Light Filter, Color Temp., Gamma, Saturation, Dynamic Dimming
(set as ON).
•
•
•
Dynamic Dimming: Synchronizes with contents while contrast changing
to execute backlight dynamic dimming.
VividPixel: Enhances the outline of the displayed picture and generates
high-quality images on screen.
ASCR: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
This function is not available (set as OFF) when Dynamic Dimming is enabled.
•
•
Aspect Control: Adjusts the aspect ratio to Full, or 4:3.
Blue Light Filter
*
Level 0: No change.
ASUS TUF Gaming Monitor VG1A series
3-3
*
Level 1~4: The higher the level, the less blue light is scattered.
When Blue Light Filter is activated,the default settings of Racing
Mode will be automatically imported. Between Level 1 to Level 3,
the Brightness function is user-configurable. Level 4 is optimized
setting. It is compliance with TUV Low Blue Light Certification.
The Brightness function is not user-configurable.
Please refer to the following to alleviate eye strains:
•
Users should take some time away from the display if working for long
hours. It is advised to take short breaks (at least 5 mins) after around 1
hour of continuous working at the computer. Taking short and frequent
breaks is more effective than a single longer break.
•
•
To minimize eye strain and dryness in your eyes, users should rest the
eye periodically by focusing on objects that are far away.
Eye exercises can help to reduces eye strain. Repeat these exercises
often. If eye strain continues please consult a physician. Eye exercises: (1)
Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes
diagonal.
•
High energy blue light may lead to eye strain and AMD (Age-Related
Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful
blue light to avoiding CVS (Computer Vision Syndrome).
3.
Color
Set a desired color setting from this menu.
ASUS TUꢀ ꢁꢂꢃiꢄg ꢅꢁ2ꢆAꢇꢈꢉA ꢊꢋR Oꢌꢌ
Rꢂꢍiꢄg Mode ꢋisplꢂyPort 2ꢎꢏ0ꢐꢉꢑꢑ0ꢒ ꢏ0ꢊꢓ
Color
Color Temp.
Saturation
Skin Tone
•
Color Temp.: Contains 4 modes including Cool, Normal, Warm, and
User Mode.
•
•
Saturation: the adjusting range is from 0 to 100.
Skin Tone: Contains three color modes including Reddish, Natural, and
Yellowish.
3-4
Chapter 3: General Instructions
4.
Input Select
In this function, you can select your desired input source.
ASUS TUꢀ ꢁꢂꢃiꢄg ꢅꢁ2ꢆAꢇꢈꢉA ꢊꢋR Oꢌꢌ
Rꢂꢍiꢄg Mode ꢋisplꢂyPort 2ꢎꢏ0ꢐꢉꢑꢑ0ꢒ ꢏ0ꢊꢓ
Input Select
HDMI-1
HDMI-2
DisplayPort
5.
MyFavorite
ASUS TUꢀ ꢁꢂꢃiꢄg ꢅꢁ2ꢆAꢇꢈꢉA ꢊꢋR Oꢌꢌ
Rꢂꢍiꢄg Mode ꢋisplꢂyPort 2ꢎꢏ0ꢐꢉꢑꢑ0ꢒ ꢏ0ꢊꢓ
MyFavorite
Shortcut
Customized Setting
•
•
Shortcut:
*
Shortcut 1/Shortcut 2: Sets the shortcut functions for shortcut
buttons.
When a certain function is selected or activated, your shortcut button may
not support. Available function choices for shortcut: GamePlus, GameVisual,
Brightness, Contrast, HDR, Blue Light Filter, Color Temp., Volume.
Customized Setting: Loads/Saves all settings on the monitor.
ASUS TUF Gaming Monitor VG1A series
3-5
6.
System Setup
ASUS TUꢀ ꢁꢂꢃiꢄg ꢅꢁ2ꢆAꢇꢈꢉA ꢊꢋR Oꢌꢌ
System Setup
Rꢂꢍiꢄg Mode ꢋisplꢂyPort 2ꢎꢏ0ꢐꢉꢑꢑ0ꢒ ꢏ0ꢊꢓ
Language
Sound
ECO Mode
Power Indicator
Power Key Lock
Key Lock
OSD Setup
DisplayPort Ver.
•
Language: There are 21 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian.
•
•
Sound: Sets the sound related settings from this menu.
*
*
Volume: The adjusting range is from 0 to 100.
Mute: Toggles the monitor sound between on and off.
ECO Mode: reduces power consumption.
This function is not available (set as OFF) when Dynamic Dimming is enabled.
•
•
•
Power Indicator: Turn the power LED indicator on/off.
Power Key Lock: Enables or disables the power key.
Key Lock: To disable all function keys. Press
over 5 seconds to
cancel the key lock function.
•
OSD Setup:
*
*
*
Adjusts the OSD timeout from 10 to 120 seconds.
Enables or disables the DDC/CI function.
Adjusts the OSD background from opaque to transparent.
•
DisplayPort Ver.: Compatibility with graphic card. Select DisplayPort 1.1
or DisplayPort 1.2+HDR by graphic card DP version.
DisplayPort 1.1 is only available when OverClocking and Adaptive-Sync
(DP)/ Variable Refresh Rate are off.
•
•
Information: Shows the monitor information.
All Reset: “Yes” allows you to restore the default settings.
3-6
Chapter 3: General Instructions
3.2
Specifications summary
Panel Type
Panel size
Max. Resolution
Pixel pitch
Brightness (Typ.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
Response time
Color temperature selection
Analog input
TFT LCD
27”W (16:9, 68.5 cm) wide screen
2560 x 1440
0.2331 mm x 0.2331 mm
350 cd/m2, 400 cd/m2 (with HDR on)
1000:1
100,000,000:1 (with ASCR on)
178˚/178˚
1.07 GM
4 ms (Gray to gray), 1ms MPRT
4 color temperatures
No
Digital input
HDMI v2.0 x 2, DisplayPort v1.2 x 1
Earphone jack
Audio input
Yes
No
Speaker (Built-in)
USB 3.0 port
Colors
2 W x 2 Stereo, RMS
Upstream x 1, downstream x 2
Black
Power LED
Tilt
White (On)/Amber (Standby)
+20˚~ -5˚
Pivot
+90˚~ -90˚
Swivel
+20˚~ -20˚
Height adjustment
VESA wall mount
Kensington lock
Voltage rating
130 mm
100 x 100 mm
Yes
AC: 100~240V
DC: 19V, 4.74A (AC adapter)
Power consumption
Power On: < 26 W**, Standby: < 0.5 W,
Power Off: < 0.5 W
Temperature (Operating)
0˚C~40˚C
Temperature (Non-operating)
-20˚C~+60˚C
Dimensions (W x H x D) without 615 x 367 x 51 mm
stand
Dimensions (W x H x D) with stand 615 x 534 x 215 mm (highest)
615 x 404 x 215 mm (lowest)
712 x 234 x 455 mm (package)
Weight (Esti.)
6.6 kg (Net); 4.3 kg (without stand); 9.0 kg
(Gross)
ASUS TUF Gaming Monitor VG1A series
3-7
Multi-languages
21 languages (English, French, German,
Italian, Spanish, Dutch, Portuguese, Russian,
Czech, Croatian, Polish, Romanian, Hungarian,
Turkish, Simplified Chinese, Traditional Chinese,
Japanese, Korean, Thai, Indonesian, Persian)
Accessories
Quick start guide, warranty card, power adapter,
power cord, DisplayPort cable (optional), HDMI
cable (optional), USB cable (optional)
Compliance and Standards
UL/cUL, CB, CE, ErP, FCC, CCC, CU, RCM,
BSMI, VCCI, RoHS, J-MOSS, WEEE, Windows
7 & 10 WHQL, CEL, MEPS, PSE, UkrSEPRO,
KCC, E-Standby, TUV-Flicker Free, TUV-Low
Blue Light, ICES-3, PC Recycle, BIS, PSB,
Vietnam Energy, CEC
*Specifications are subject to change without notice.
**Measuring a screen brightness of 200 nits without audio/ USB/ Card reader
connection.
3-8
Chapter 3: General Instructions
3.3
Outline dimensions
ASUS TUF Gaming Monitor VG1A series
3-9
3.4
Troubleshooting (FAQ)
Problem
Possible Solution
Power LED is not ON
•
•
Press the
is in the ON mode.
Check if the power cord is properly
connected to the monitor and the power
outlet.
button to check if the monitor
The power LED lights amber and there is
no screen image
•
•
•
•
Check if the monitor and the computer are
in the ON mode.
Make sure the signal cable is properly
connected the monitor and the computer.
Inspect the signal cable and make sure
none of the pins are bent.
Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
•
•
Adjust the Contrast and Brightness
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
Make sure the signal cable is properly
connected to the monitor and the
computer.
•
Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure
not look white)
that none of the pins are bent.
Perform All Reset via OSD.
Adjust the R/G/B color settings or select
the Color Temperature via OSD.
•
•
3-10
Chapter 3: General Instructions
3.5
Supported operating mode
Resolution frequency
HDMI
Refresh rate
60Hz
DP
Refresh rate
60Hz
640x480
640x480
67Hz
67Hz
640x480
72Hz
72Hz
640x480
75Hz
75Hz
720x400
70Hz
70Hz
800x600
56Hz
56Hz
800x600
60Hz
60Hz
800x600
72Hz
72Hz
800x600
75Hz
75Hz
832x624
75Hz
75Hz
1024x768
1024x768
1024x768
1152x864
1280x1024
1280x1024
1440x900
1920x1080
1920x1080
1920x1080
2560x1440
2560x1440
2560x1440
2560x1440
2560x1440
2560x1440
2560x1440
2560x1440
60Hz
60Hz
70Hz
70Hz
75Hz
75Hz
75Hz
75Hz
60Hz
60Hz
75Hz
75Hz
60Hz
60Hz
60Hz
60Hz
100Hz
120Hz
60Hz
100Hz
120Hz
60Hz
100Hz
120Hz
144Hz
Not supported
Not supported
Not supported
Not supported
100Hz
120Hz
144Hz
155Hz
160Hz
165Hz
170Hz
ASUS TUF Gaming Monitor VG1A series
3-11
Video Timing
Resolution frequency
HDMI
Refresh rate
59.94Hz
60Hz
DP
Refresh rate
Not supported
Not supported
50Hz
720x480P
720x480P
720x576P
50Hz
1280x720P
1280x720P
1280x720P
1440x480P
1440x480P
1440x576P
1920x1080P
1920x1080P
1920x1080P
1920x1080P
1920x1080P
3840x2160p
3840x2160p
50Hz
50Hz
59.94Hz
60Hz
59.94Hz
60Hz
Not supported
60Hz
59.94Hz
60Hz
50Hz
50Hz
30Hz
Not supported
50Hz
50Hz
59.94Hz
60Hz
59.94Hz
60Hz
120Hz
50Hz
120Hz
Not supported
Not supported
60Hz
3-12
Chapter 3: General Instructions
|
