ABB C1900 QC User Manual

Displays and controls  
Recorder Faceplate  
Controller Faceplate  
ABB ME ASUREMENT & ANALY TICS | IM/C1900 - QC  
C1900 recorder and  
recorder/controller  
Quick reference guide  
Bar Graph (Indicates deviation of  
measured value from set point)  
1008  
1008  
AL  
RMT  
AT  
MAN  
CH1  
CH2  
CH3  
CH4  
AL1  
AL2  
AL3  
AL4  
Alarm Status  
Process  
Variable  
Alarm  
Currently  
Displayed  
Channel  
Manual Control  
Remote Set  
Point in Use  
Auto-tune  
in Progress  
Operating Guide  
Alarms  
Programming Guide  
Alarms .....................................10  
Status  
Advance tonext page  
Acknowledge ................ 16, 36 Analog outputs ........................21  
LED status ................... 16, 36 Auto/manual select enable ......45  
Auto-tune ................................21 Bargraph increment .................45  
Enable/disable .....................23 Chart set up ..............................9  
Setup ...................................21 Configuration  
Sideways Scroll  
Page 1  
Page 2  
Frame 1  
Frame 2  
Frame 1  
Frame 2  
Down Scroll  
Advance to  
next frame  
Status ..................................23  
Auto/manual select..................12  
Chart .........................................4  
Control  
Basic......................................3  
Control .................................29  
Advanced ............................48  
Control.....................................37  
Action on input fail ...............43  
Action on power fail .............39  
Raise and Lower  
Parameter Value  
Adjust  
Cascade ..............................12  
Heat/cool ...................... 11, 12  
or  
On/off ........................... 26, 30 Digital outputs .........................19  
Output adjust .......................13 Function keys ..........................49  
Standard ....................... 10, 26 Inputs (PV, RSP, P-FB) ..............4  
Parameter  
X
Y
Z
Select  
Displays & controls ... 5, 6, 34, 35  
Assign ..................................53  
Function Key  
Alarm acknowledge; Auto-tune; Pen lift/ lower;  
Profile Control; Local/Remote or 'Home' – See  
Programming Guide, 'Advanced Configuration'  
Fault-finding.............. 2, 9, 24, 38 Logic equations .......................50  
Auto-tune diagnostics..........24 Logic inputs ................ 23, 46, 47  
Input error messages ............. 9 Passwords...............................24  
Power up error codes ............2 Pen ....................................... 8, 9  
Pen Lift  
Manual tuning ..........................28  
Pen – fitting ............................... 4  
Functions .............................52  
Scale adjust .................. 26, 27  
(Recorder Only) Raises and lowers the chart pen.  
Process variable ......................13 Position feedback – see Inputs  
Profile control ..........................12 Process variable – see Inputs  
Program select ....................19 Relays ............................... 16, 17  
Reset ...................................19 Remote set point – see input.......  
Skip segment.......................19 Retransmission outputs – see  
Auto/Manual  
(Controller Only) Switches between automatic  
and manual control modes.  
Note. All programming is carried out using the  
faceplate keys and displays.  
Analog Outputs  
Status ..................................15  
Security Access  
Scale Adjust (span/offset) ........26  
Set point ......................30–33, 45  
Spot calibration – see Scale Adjust  
Configuration level ...............18  
Password.............................18  
Tune level – access .............18  
Self-test ..................................... 2  
Set point  
ABB Limited  
Measurement & Analytics  
Howard Road, St. Neots, Cambridgeshire, PE19 8EU, UK  
Tel: +44 (0)870 600 6122 | Fax: +44 (0)1480 217948  
Installation Guide  
Accessories ...............................2  
Electrical Installation ..................6  
Siting .........................................3  
Mounting/Dimensions ............... 4  
Power Supplies .......................12  
Inputs/Outputs ..........................7  
Bias .....................................14  
Ratio ....................................14  
Type selection......................14  
Time/date ................................15  
Totalizer ............................ 17, 37  
© ABB 2018 | Specifications subject to change without notice.  
10000  
9999  
SECOdE  
MMMMMM  
OPrtOr  
LEVEL  
Note. Refer to the relevant page of the Programming Guide for further information.  
SEtup  
INPUt  
SEtUP  
SEtUP  
CH Art  
SEtUP  
bASIC  
PENrNG  
ALArMS  
CONFIG  
SEtUP  
Setup Inputs – p4  
Setup Pen Range – p8  
Used to adjust the  
'magnification' of the  
trace. Default is 0 to  
100% of engineering  
range.  
Setup Chart Speed – p9 Setup Alarms – p13  
rELAYS  
Set the type, linearizer,  
ranges and fault levels for  
each input – see overleaf.  
Set the duration of one  
chart revolution and pen  
lift/drop parameters.  
Set alarms to trip on  
process value, control  
output , setpoint  
deviation, rate of change.  
Set in engineering units.  
SEtUP  
ALArMS  
SEtUP  
dIGtAL  
OUtPtS  
SEtUP  
dIGtAL  
INPUtS  
ACCESS  
PAGE  
SCALE  
rELAYS  
ANALOG  
ADJUSt  
Setup Relays – p15  
Set source used to  
activate each relay and  
define normally  
Setup  
Setup  
Setup  
Access Page – p22  
Disable access to  
configuration and tuning  
facilities.  
Scale Adjustment – p24  
Allows spot calibration to  
eliminate system loop  
errors.  
Digital Outputs – p18  
Set source used to  
activate each output and  
define normally  
Analog Output – p20  
Set an output as control  
or re-transmission.  
Digital Input – p21  
Set polarity of external  
digital signals.  
open/closed state.  
open/closed state.  
Setting analog input links  
Configuring analog inputs  
1000  
999  
SECOdE  
MMMMMM  
OPrtOr  
LEVEL  
Information. The alphabet used to  
display page and parameter titles is  
as follows:  
A –  
B –  
C –  
D –  
E –  
F –  
G –  
H –  
I –  
M –  
N –  
O –  
P –  
Q –  
R –  
S –  
T –  
U –  
V –  
Y –  
A
b
C
d
E
F
G
H
I
J
K
L
M
N
O
P
Q
r
S
t
U
V
Y
or  
or  
n
bASIC  
SEtup  
INPUt  
or  
or  
c
h
o
2
3
4
5
6
CONFIG  
Select Channel – Choose the input channel to  
be configured  
SELECt  
J –  
K –  
L –  
____  
5
8
4
1
5
8
4
1
mA V RTD &  
Resistance  
mV THC  
or  
or  
Input type _A_P(mA), VOLt(V), _ULt(mV),  
tCPL(Thermocouple), rtd(RTD) and LO OH  
(< 750 Ohms) H I OH (> 750 Ohms).  
INtYP  
____  
PL8  
PL8  
2-wire  
Transmitter  
1
4
3
1
4
All Other  
Input Types  
ENG-H I  
2
2
3
Decimal Point: Select the decimal point position  
for the process variable, e.g. 300.0.  
Linearizer: If using a thermocouple set to J, K,  
B, N, E, T, S, A. Other options are 5/2, 3/2,  
SQrt, rtdor NONE.  
LNtYP  
___  
dEC-Pt  
Fig. 1 Input Links – Channel 1  
____  
PL3  
PL3  
Engineering Range Low: Select the lowest  
engineering value that will be displayed when the  
input is at its minimum value – e.g. for an  
engineering range of 0 to 300.0 °F set to 00.  
3
4
2
1
3
4
2
1
Range High: For a 4 to 20mA current input, set  
this to 2000, or for 0 to 5V, set to 50. The frame  
does not appear if tCPLor rtdare used.  
rNG-H I  
___  
ENG-LO  
___  
2-wire  
Transmitter  
All Other  
Input Types  
INPUT/OUTPUT MODULE  
Broken Sensor Drive: Determine pen action  
when the input signal fails: NONE– pen follows  
failed input; UP– pen driven to full scale;  
dN– pen driven to zero scale.  
Range Low: Set the low end of the electrical  
input range, e.g. 4 00, for 4 to 20mA, or 00for  
0 to 5V.  
rNG-LO  
___  
bSPd  
___  
Fault Detection Drive: Determine maximum  
input travel outside engineering range before an  
error is detected. E.g. for a 0 to 300°F range, a  
10% fault level will trigger at 330°F.  
Units: Select NONEif the input is not temperature,  
otherwise select dEG For dEG C.  
UNItS  
___  
FdLP  
___  
4
5
1
8
4
1
mA V RTD &  
Resistance  
mV THC  
8
5
PL1  
PL1  
Input Filter: Adjust the instrument response time  
from 0 to 60 seconds in one second increments  
to reduce pen jump & dampen out noisy signals.  
Engineering Range High: Select the highest  
engineering value that will be displayed when the  
input is at its maximum value – e.g. for an  
engineering range of 0 to 300.0 °F set to 3000.  
ENG-H I  
____  
PrGFLt  
___  
Warning. Ensure that the unit is isolated from all power  
supplies before removing I/O boards.  
dEC-Pt  
Fig. 2 Input Links – Channels 2 to 4 (If fitted)  

Weed Eater Automobile Parts Hp22 User Manual
Trion Cv Series User Manual
Toshiba Air Conditioner Rav Sm806bt Tr User Manual
Sima Products Udc 1 User Manual
Sennheiser Szl1011 User Manual
MIELE CVA 615 User Manual
EMERSON MW9712B User Manual
DELL WYSE 3010 User Manual
DELL VOSTRO 3450 02 User Manual
ASUS VS229N User Manual