3300 Rx Doorbell User Manual

Wired+Wireless Designer Doorbell  
Model PC-5870  
6. A small electrical component called a ‘diode’ is supplied with the chime. Install the diode  
across the terminal screws of the Front Doorbell pushbutton as shown in Figure 2 & 3.  
Without this diode the chime will not work. Connect the wires to the Front Doorbell Pushbutton.  
Install the Front Doorbell Pushbutton in the desire location using the screws provided.  
7. Turn the power on.  
Instructions - Please retain these instructions for future reference.  
You have purchased a Universal Door Chime that serves all residential applications. It can be installed  
as a Wired chime, where the power is supplied by a transformer with wires, or it can be a Wireless  
chime powered by 3 C cell batteries. Use the following guidelines to assist you in deciding the mode  
that best serves your application:  
If you are building a new house:  
WIRELESS MODE  
You will require: (for Wireless option)  
The Wired mode would be best if you are having an electrician install the door chime.  
The electrician will install a transformer and run the wires for the door chime as well as pushbuttons.  
You can also elect to use the Wireless mode. However, the batteries in the chime and  
pushbuttons will need to be replaced periodically.  
A small Phillips head screwdriver.  
Doorbell Pushbuttons  
3 C cell batteries  
2 screws for installing doorbell pushbutton  
If you are replacing a working Wired Doorbell:  
The Wired mode would be the best option.  
.
1. Install the door chime using the hardware supplied.  
2. Mount the IQ America Wireless Pushbutton following the  
instructions provided and install the battery in the pushbutton.  
3. Insert the C cell batteries in the order shown in Figure 4.  
The Chime will play all of the tunes that are available when it is first powered up.  
4. Program the wireless IQ America pushbuttons to the door chime  
a. Press the front door pushbutton. The door chime will respond with a chime.  
b. Program a second pushbutton at this time. Programming must be completed within  
2 minutes of programming the first pushbutton. If more than 2 minutes has elapsed, go  
to the To Reset the Chime Programming.  
Figure 4  
If you have a wired doorbell, but it doesn’t work:  
First install this chime in the Wired mode. Connect the wires as explained in the section  
“Replacing a Wired Doorbell”. If the chime works, this is the best option.  
If the chime does not work, purchase either 1 or 2 IQ America Wireless Pushbuttons and follow the  
instructions for the Wireless mode.  
If your home does not have a wired doorbell, you should use the Wireless Mode.  
This package contains:  
Universal Chime and Decorative Cover  
2 screws and 2 wall plugs for installing door chime  
1 Diode  
To Reset the Chime Programming, press and hold button A and B (Fig. 5) until the chime  
sounds. The chime will play all of the tunes available indicating that previous programs have been  
erased. Return to the Program the Doorbell Pushbutton Transmitter and repeat section.  
WIRED MODE: New Installations  
New installations will require a 16V 10W transformer. It is suggested that this be installed by  
a licensed electrician.  
Sound Selection: Refer to Figure 5 to select the sound  
1. Press button A until the desired tone for the front doorbell is heard (See Tune Options Table).  
Press the Front Doorbell Pushbutton to test the chime. (The chime tone can be changed at any  
time by simply pressing this button to select another tone.)  
2. If a Back Doorbell Pushbutton is used. Press button B until the desired tone is heard. Press  
the Back Doorbell Pushbutton to test the chime.  
You will require: (for Wired option)  
A small Phillips head screwdriver.  
(For new installations) Transformer 16V 10W (IQ America DT1610)  
(For new installations) 2 Doorbell Pushbuttons  
4 screws for installing doorbell pushbutton  
1 Diode  
3. Adjust the volume with the volume adjustment knob C.  
Chime Options Table  
1. Big Ben 2notes  
2. Big Ben 8notes  
3. Traditional 1note  
4. Traditional 2notes  
5. Traditional 8notes  
6. Birthday Song  
Installing the Transformer  
7. Merry Christmas  
8. Auld Lang Synn  
9. Beethoven  
Warning: Turn power off at fuse or circuit breaker before installing transformer. Transformer should  
be mounted on or near a junction box. They can also be mounted to the electrical service panels.  
Junction boxes in utility rooms, crawl spaces, or basement are preferred. Avoid attic locations. Failure  
to use a transformer with adequate power will result in loss of sound or may result in the chime being faulty.  
Contact a qualified electrician if you have any questions as to the suitability of the system or any doubts  
about your ability to wire this correctly.  
10. U.S. National Anthem  
Figure 5  
Replace the Decorative Chime Cover  
as shown in Figure 6. Position the decorative  
cover and press down until it snaps in place.  
The cover can be installed in either direction.  
Remove Decorative Chime Cover  
Remove the decorative cover by simply pulling it away from the rear casing. When replacing  
the cover, simply press it back on the base.  
Install the Door Chime (Refer to Figure 1)  
Position the chime as shown in Figure 1. (The chime base can also be installed in the  
horizontal position.) Route the wires as shown and install the chime using the screws provided.  
Specification  
Range……………………...........…………….……..Up to 300 ft  
Figure 6  
Power supply………………………………….……..16V Transformer  
Diode  
Wire Entrance  
Hole  
Troubleshooting For Wired Chime  
Chime Not Sounding:  
Check that power to the chime is turned on.  
TOP  
Verify Diode is attached securely to the Front Door bell Pushbutton.  
Diode may be positioned at the wrong polarity. Reverse the diode.  
5/8” Round  
Push Button  
Verify all wires are securely fastened to terminals and that the wiring is correct.  
Push Button  
Chime Sounds Only While Keeping Pushbutton Pressed  
Figure 1  
Figure 2  
Reverse the direction of the diode on the front door pushbutton.  
Wiring Instructions For New Installation (Refer to Figure 3)  
1. Turn off the power supply.  
2. Connect one wire from the Front Doorbell Pushbutton to the FRONT terminal of the Chime Base.  
3. Connect the other wire from the Front Doorbell Pushbutton to one Terminal of the Transformer.  
Troubleshooting For Wireless Chime  
Chime Not Sounding:  
Check that all batteries have been inserted correctly. The doorbell pushbutton LED  
light should come on when the pushbutton is pressed.  
4. Connect the TRANS  
terminal of the Chime to  
the other Terminal of the  
Transformer.  
Chime may be positioned out of range of the doorbell pushbutton.  
Move your chime closer to the doorbell pushbutton.  
Note: During the programming cycle, the transmission range may be  
reduced and will resume optimum range after 2 minutes.  
5. If the Back Doorbell  
Pushbutton is used,  
connect one end of the  
wire from the Back  
Doorbell Pushbutton to  
the REAR terminal of  
the Chime.  
A metallic object may be blocking the signal from the doorbell pushbutton.  
Experiment with the location of the chime to see if you can move it in to a more suitable place.  
The battery in the doorbell pushbutton or chime may need replacing.  
If the pushbutton LED light (B) flashes 5 times after being pushed, replace the battery.  
Note: When replacing batteries the chime will retain its programming.  
Note: In cold conditions, poor location or environment, operating at maximum range it is  
advisable to replace the battery more frequently before the indicator light flashes  
(i.e. every 12-18 months) to maintain optimum performance.  
6. Connect the other end of  
the Back Doorbell Pushbutton  
to the 1st Terminal of the Transformer.  
Figure 3  
The doorbell pushbutton and chime haven’t been programmed.  
Reset the automatic programming of your chime and doorbell pushbutton by Pressing and  
holding down chime selection buttons A and B (Figure 5) for 5 seconds. The chime will sound  
all of the tunes a vailable indicating the programming has been erased. Program the doorbell  
pushbutton following the installation instructions.  
7. Turn on the power to the doorbell.  
8. Press the doorbell pushbutton. The chime should respond with a tune. If not, go to the  
Troubleshooting section.  
For any other problem, call 1-800-296-1869 Mon-Fri between 9 am and 5pm EST  
Install the Front Doorbell Pushbutton (Refer to Figure 2)  
IQ America Five Year Warranty  
A small electrical component called a ‘diode’ is supplied with the chime. Install the diode across the  
terminal screws of the Front Doorbell pushbutton as shown in Figure 2 & 3. Without this diode the  
chime will not work. Connect the wires to the Front Doorbell Pushbutton. Install the Front Doorbell  
Pushbutton in the desire location using the screws provided.  
This is a “Limited Warranty” which gives you specific legal rights. You may also  
have other rights which vary from state to state and province to province.  
For a period of five years from the date of purchase, any malfunction caused by factory  
defective parts or workmanship will be corrected at no charge to you. To obtain a refund or a replacement,  
return the product to the place of purchase.  
NOT COVERED: Repair service, adjustment and calibration due to misuse abuse or  
negligence. Unauthorized service or modification of the product or of any furnished component will void this  
warranty. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of  
use or unauthorized service.  
This warranty covers only IQ America products and is not extended to other equipment  
and components that a customer uses in conjunction with our products.  
This warranty is expressly in lieu of all other warranties, express or implied, including any  
warranty, representation or condition of merchant ability of that the products are fit for any particular purpose  
or use, and specifically in lieu of all special, indirect or incidental or consequential damages.  
Repair or replacement shall be the sole remedy of the customer and there shall be no liability  
on the part of IQ America for any special, indirect, incidental or consequential damages, including but not  
limited to any loss of business or profit, whether or not foreseeable. Some states or provinces do not allow  
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may  
not apply to you. Retain receipt for warranty claims.  
Install the Back Doorbell Pushbutton (Refer to Figure 2)  
Connect the wires to the Back Doorbell Pushbutton. Install the Back Doorbell Pushbutton in the desired  
location using the screws provided (No diode required).  
Replacing a Wired Doorbell  
1. Turn off the power supply.  
2. Remove the decorative cover by simply pulling it away from the rear casing. When replacing  
the cover, simply press it back on the base.  
3. Use tape to mark the wires and then disconnect the wires from doorbell.  
4. Position the chime as shown in Figure 1. (The chime base can also be installed in the  
horizontal position.) Route the wires as shown and install the chime using the screws provided.  
5. Connect the wires to the Door Chime.  

Xantrex Technology Xc3012 User Manual
Trion M1100 User Manual
Toshiba E Studio 855 User Manual
Sterling Power Products 1220ce User Manual
Sanyo Cr485gx56 User Manual
Samsung Aq24a1 2 Rcd User Manual
Porter Cable Pci2200 User Manual
Murphy Diesel Fuel Check Valves Prv50 User Manual
HANSGROHE AXOR CARLTON 17374XX1 User Manual
CROSLEY XUF14 User Manual