White Rodgers Ecd1500w User Manual

Media Air Cleaner

Épurateur d’air Média

• MCS600W

OWNER’S MANUAL

• MCS600B

• MCD1200W

• MCD1200B

MANUEL OPÉRATEUR

Electronic Air Cleaner

Épurateur d’air Électronique

• ECS750W

• ECS750B

• ECD1500W

• ECD1500B

2SD1

Electrostatic Electric

Air Cleaner Fan

2SD2

White-Rodgers is a division of Emerson Electric Co.

www.white-rodgers.com

Table of contents

IMPORTANT SAFETY INSTRUCTIONS ..............................................................................2

OPERATING INSTRUCTIONS ...........................................................................................3

INTRODUCTION .................................................................................................................3

PRODUCT DESCRIPTION .....................................................................................................3

2.1 Filter package .................................................................................................................................. 3

2.2 Optional feature ............................................................................................................................... 3

MOUNTING/INSTALLATION .................................................................................................3

3.1 Technical specifications .................................................................................................................... 3

3.2 Air cleaner mounting/installation ........................................................................................................ 3

MAINTENANCE ..................................................................................................................3

4.1 Filter replacement/cleaning frequency ................................................................................................. 3

4.2 Cleaning the outside of the air cleaner ................................................................................................ 3

CONTROL ..........................................................................................................................4

5.1 Controlling with the panel button ....................................................................................................... 4

5.2 Remote Control operation .................................................................................................................. 4

5.3 Automatic operation (auto mode) ....................................................................................................... 4

PROGRAM SETTINGS .........................................................................................................4

6.1 Program Setting 1: Service Indicator ................................................................................................... 4

6.2 Program Setting 2: Resetting the Service Indicator ............................................................................... 4

TROUBLESHOOTING ...........................................................................................................5

TECHNICAL REPAIR GUIDE .............................................................................................6

ADJUSTING TO SPECIFIC ROOM CONDITIONS ......................................................................6

FILTER REPLACEMENT/CLEANING ........................................................................................7

9.1 Prefilter replacement ......................................................................................................................... 7

9.2 Electronic filter cleaning .................................................................................................................... 7

9.3 Media filter replacement .................................................................................................................... 8

9.4 Activated carbon or Odor Free filter replacement .................................................................................. 8

10 BASIC SERVICE GUIDE .......................................................................................................9

PARTS LIST ................................................................................................................ 10

0508082120/101203/C

Page 2

Owner’s manual

Important Safety Instructions

Read and save these instructions

Mounting/installation

Please follow the installation instructions carefully.

ATTENTION

Please read instructions before installing and using the air

cleaner. This will help you obtain the full benefit from the air

cleaner you have selected.

Disconnect power prior to installing the air cleaner.

To reduce the risk of electric shock this equipment has a

grounding type plug that has a third (grounding) pin. This plug

will only fit into a grounding type power outlet.

If the plug does not fit into the outlet contact qualified

personnel to install the proper outlet. Do not alter the plug in

any way.

A Read the Owner’s Manual and Important Safety Instructions

carefully. Failure to follow these instructions could cause a

malfunction of the filter or unsatisfactory service.

B Follow a regular service and maintenance schedule for

efficient operation.

Use common sense, stay vigilant and pay attention to your

actions during installation. Do not install the air cleaner when

tired or affected by drugs, alcohol, medicines or otherwise

impaired.

To reduce the risk of electric shock, fire and injury to persons:

•

Do not use the air cleaner in wet or damp locations.

The air cleaner is not for use in cooking areas.

Do not use the air cleaner with any solid state speed control

device.

Use only screws delivered in the installation kit. Using other

screws may damage the air cleaner and can cause a risk of

shock, fire or injury to persons.

•

Do not use the air cleaner outdoors.

Do not use the air cleaner at ambient temperatures above

95°F/35°C.

Do not use excessive strength to fasten the screws of the

mounting assembly accessories. It will damage the air cleaner

or mounts causing the air cleaner to fall.

Do not remove a wall mounted air cleaner once it is installed.

Take special care when cleaning a wall mounted air cleaner.

Only use the special mounting kit for recessed ceiling mounted

air cleaners.

WARNING

ELECTROCUTION HAZARD.

Disconnect mains before servicing. Failure to do so

could result in serious personal injury or death.

Do not use the frame of the recessed ceiling to carry the weight

of the air cleaner.

WARNING

Fire hazard

Do not attempt installation of this unit unless you are familiar with

the necessary tools, equipment, utility connections and potential

hazards.

Installation should be performed only by a qualified service provider.

Failure to do so could result in reduced performance of the unit,

serious personal injury or death.

Never use the air cleaner in areas with flammable gasses.

Never use the air cleaner to extract and/or filter flammable,

smoldering or burning material.

Never use the air cleaner to extract and/or filter toxic fumes or

abrasive particles.

Do not place any objects on top of the air cleaner.

Do not use with a damaged cord or plug.

CAUTION

CELLS MAY CONTAIN SHARP EDGES.

Do not pull the cord to remove the plug from the mains. Protect

the cord against heat, oil and sharp objects. Do not run any

appliance over the cord. To unplug, grasp the plug, not the

cord. Do not pull or carry by cord, use cord as a handle, close

a door on cord, or pull cord around sharp edges or corners.

Do not move the air cleaner without having it unplugged first.

Use care when servicing unit or handling cells. Failure

to do so could result in minor personal injury.

WARNING

Installation of this unit must comply with local electric codes or other

applicable codes.

Review and understand local codes prior to installation.

Do not use this apparatus in a flammable or explosive atmosphere.

Failure to do so could result in serious personal injury or death.

0508082120/101203/C

Page 3

Owner’s manual

Operating Instructions

INTRODUCTION

•

For ceiling mounting of the air cleaners, use installation kit

# F801 0195. For a single air cleaner one set is required, for

the double air cleaner two sets are required.

This manual provides instructions for the mounting/installation,

control and maintenance of the air cleaner. The safety

instructions should be read first.

For recessed ceiling mounting of the single air cleaner use

installation kit # F801 0196.

PRODUCT DESCRIPTION

For the double air cleaner, use installation kit # F801 0197.

The air cleaner is provided with an Air Quality Analyzer. It

measures the local pollution continuously and adjusts the fan

speed accordingly. The analyzer is sensitive to pollution in

gaseous form that occurs in, for example, tobacco smoke.

There are no components for mounting to the ceiling or wall in

these kits.

Ensure that the load capacity of the mounting devices is

sufficient to safely support the air cleaner. The weights of the

air cleaner are maximum 39.9 lbs. and 65.5 lbs. respectively.

2.1 Filter package

See fig. 1 on page 25

The polluted air is cleaned in three successive stages.

For the single air cleaner on a pedestal, use pedestal installation

kit # F848 0384.

2.1.1 Prefilter [A]

The prefilter traps the coarser dust particles and other

pollutants.

Use the materials prescribed during the installation. Connect the

air cleaner to power only after complete installation.

2.1.2 Electronic filter [B]

The electronic filter has a very high efficiency and traps dirt

particles larger than 0.01 micron;

MAINTENANCE

Maintain your air cleaner carefully and regularly. If poorly

maintained, it can be a fire hazard. Always disconnect the air

cleaner from power during maintenance and cleaning.

or (in case of a media filter):

2.1.3 Media filter [B]

The media filter is folded in such a way that it has a large

effective surface area. This gives a low air resistance and a high

dirt collection capacity.

Adhere to the maintenance instructions and advice on filter

replacement.

Replace or clean the filters on time.

2.1.4 Activated carbon filter [C]

The activated carbon filter adsorbs unpleasant smells.

Only use manufacturer's original replacement parts.

2.2 Optional feature

Inspect the product for damages regularly. The safety features

should be checked regularly for proper functioning and, if

required, be repaired immediately.

The cord should be checked regularly and, if damaged, replaced

by a qualified service person.

2.2.1 Odor Free

If the air cleaner is provided with an Odor Free filter obnoxious

odors can be suppressed. The standard activated carbon filter

is replaced by the Odor Free filter.

4.1 Filter replacement/cleaning frequency

MOUNTING/INSTALLATION

Filter replacement/cleaning frequency depends on local

conditions, the fan speed selected and the operating time of the

air cleaner. The Service Indicator can be used to help determine

the filter replacement/cleaning frequency. See Program Settings

step 1.

3.1 Technical specifications

Single

Double

Dimensions

24.8x24.4x11.4 in.

24.8x41.3x11.4 in.

8.3 in.

A crackling or snapping sound will be heard occasionally during

use of the air cleaner. This is normal and is caused by high

voltage arcing in the filter. Cleaning the electronic filter is

necessary when the crackling or snapping is heard frequently.

Max. built-in height

Weight

8.3 in.

max. 39.9 lbs.

max. 65.5 lbs.

Power consumption:

- electronic

- media

130 W

118 W

225 W

222 W

Filter replacement/cleaning may be done as described in the

technical repair section.

Voltage

115V, 60Hz

4.2 Cleaning the outside of the air cleaner

3.2 Air cleaner mounting/installation

The air cleaner can be installed in several ways using different

installation kits.

Wipe the outside of the air cleaner with a moist cloth. Do not

use cleaning products that contain ammonia or abrasives. The

air cleaner is not resistant to organic solvents, such as benzene,

etc. It is possible that the Air Quality Analyzer temporarily

reacts abnormally with exposure to cleaning agents.

•

For wall mounting use installation kit # F801 0193. This kit

is only suitable for single air cleaners.

0508082120/101203/C

Page 4

Owner’s manual

Operating Instructions

CONTROL

PROGRAM SETTINGS

See fig. 5 on page 25

Do not close all vents simultaneously as this may result in the

motor/fan overheating.

The air cleaner is shipped with factory default program settings.

The following program settings allow you to customize the air

cleaner operation for your personal preference.

The product is designed solely for cleaning air indoors and must

not be used for any other purpose.

•

Program Setting 1: Service Indicator

Program Setting 2: Resetting the Service Indicator

The user is liable for damages resulting from improper use. Do

not use the air cleaner when parts or safety devices are faulty,

absent or damaged.

PROGRAM: press this button once to get in the program mode.

While in the program mode if no key is pressed for 60 seconds

the air cleaner will return to the last setting without saving any

changes.

The air cleaner can be controlled in three different ways:

6.1 Program Setting 1: Service Indicator

A Using the panel button (>>button), for selecting fan speed

or AUTO mode

B Using the remote control

The Service Indicator is used to predict when the filter will need

cleaning (electronic air cleaners) or replacement (media air

cleaners).

C Using the Auto Clean mode (AUTO mode)

The Service Indicator automatically calculates the service

interval based on the pollution level selected and the fan speed.

When the filter becomes clogged the leds • and •••• will flash

each time the air cleaner is turned on.

5.1 Controlling with the panel button

See fig. 2 on page 25

The panel button (>> button) allows you to control the fan

speed as follows:

Pollution level guidelines for establishing setting:

With the air cleaner OFF:

•

Press the panel button (>>); control goes to AUTO.

• LOW DUTY: general pollution without tobacco smoke

•• MEDIUM DUTY: moderate tobacco smoke concentrations

••• HEAVY DUTY: high tobacco smoke concentrations

•••• EXTREME DUTY: extremely high tobacco smoke

concentrations

Press the panel button (>>); fan speed goes to •••• (TURBO).

Press the panel button (>>); fan speed goes to ••• (HIGH).

Press the panel button (>>); fan speed goes to •• (MEDIUM).

Press the panel button (>>); fan speed goes to • (LOW).

Press the panel button (>>); fan speed goes to STANDBY.

Press the panel button (>>); fan speed switches OFF.

To select the pollution level:

•

Press PROGRAM; you are in the program mode 1 and STANDBY

led will flash once every two seconds.

Default: OFF (all leds off).

Press V: led • (LOW) will light up, meaning you've set the

pollution level to LOW DUTY.

Press V: led •• (MEDIUM) will light up, meaning you have set

the pollution level to MEDIUM DUTY.

Press V: led ••• (HIGH) will light up, meaning you have set

the pollution level to HEAVY DUTY.

Press V: led •••• (TURBO) will light up, meaning you have set

the pollution level to EXTREME DUTY.

If you want to go back to one of the previous pollution

If you keep pressing on the panel button (>>), the control will

go one step every second.

•

5.2 Remote Control operation

See fig. 3 on page 25

Remote Control Fan Speed Indicators:

•

• LOW

•• MEDIUM

••• HIGH

•••• TURBO

levels, press W.

Press PROGRAM to confirm setting 1 and to go to setting 2.

Note: When the motor is turned ON, from STANDBY, the air

cleaner will start automatically on TURBO for 1.5 seconds.

Subsequently it will switch to the last fan speed selected.

6.2 Program Setting 2: Resetting the Service Indicator

The indicator needs to be reset when the media filter is changed

out. If led • and led •••• are flashing, it is time to change the

filter(s) and to reset the indicator.

•

OFF: switches off air cleaner.

V and W : fan speed goes one level higher (V) or lower (W).

AUTO: switches the air cleaner to automatic operation.

To Reset:

•

5.3 Automatic operation (AUTO mode)

See fig. 4 on page 25

Press PROGRAM: you are in the program mode 2 and the

STANDBY led will flash twice every two seconds.

Default: OFF (all leds are off).

If the indicator is programmed (setting 1), you will see all the

leds switched on in setting 2, provided the Service Indicator

is in use for a while.

Reset Service Indicator: press OFF (all leds are off).

Press PROGRAM: all user settings are saved and the air

cleaner is back in normal control.

Press AUTO on the remote control.

•

There is a 5 minute warm up time for the Air Quality Analyzer.

It is recommended the air cleaner be plugged in continuously to

avoid the warm-up delay. If you activate AUTO during this time,

the led on the control panel will flash. After 5 minutes you will

hear a beep and the air cleaner will operate automatically.

•

0508082120/101203/C

Page 5

Owner’s manual

Operating Instructions

TROUBLESHOOTING

If leds • and •••• are flashing:

This is the Service Indicator. It signifies time to service (replace

or clean) the filter(s).

Pressing any button will turn off the Service Indicator leds.

When the unit is switched on again the Service Indicator will

resume flashing. After changing the filter(s), the Service

Indicator should be reset in Program Setting 2. Contact your

service person.

If led AUTO is flashing:

Air Quality Analyzer is warming up. After 5 minutes the Air

Quality Analyzer is ready and air cleaner will start running in

AUTO mode.

If led STANDBY is flashing:

High Voltage Output problem in the collecting cell(s).

If there is a dead short in the cell for over 60 seconds the

STANDBY led flashes. Power will be interrupted to the cell(s) for

10 minutes which may allow the cause of the problem (e.g.

hair) to flow out of the collecting cell. After 10 minutes the high

voltage will return to the cell. If there is still a short in the cell

the high voltage will again be interrupted for 10 minutes, etc.

This loop stops at the fourth time a dead short condition is

detected. Upon detection, the software blocks the fan control

and the unit quits operating. The collecting cell should be

cleaned to see if it can be returned to service or requires further

repair. Contact your service person.

Note: After one crackle or snap (arcing) the high voltage will

drop to 7000 Volts and slowly build up to the programmed

output. If there are more than 20 crackles or snaps during one

minute, the software blocks the high voltage for 45 seconds,

after which the voltage slowly rebuilds.

0508082120/101203/C

Page 6

Owner’s manual

Technical Repair Guide

WARNING: RISK OF ELECTRIC SHOCK

These servicing instructions are for use by qualified personnel

only. To reduce the risk of electric shock, do not perform any

servicing other than that contained in the operating instructions

unless you are qualified to do so.

This guide contains service checks to assist service personnel

in locating and correcting any condition that might occur to

render the air cleaner ineffective or inoperative. The air cleaner

has been designed with replaceable components, such as the

high voltage power supply which allows the service person to

simply replace a component rather than attempt repair of

components in the field.

Program Setting 2: Resetting the Service Indicator

The indicator needs to be reset when the media filter is changed

out. If led • and led •••• are flashing, it is time to change the

filter(s) and to reset the indicator.

To Reset:

•

Press PROGRAM: you are in the program mode 2 and the

STANDBY led will flash twice every two seconds.

Default: OFF (all leds are off).

If the indicator is programmed (setting 1), you will see all the

leds switched on in setting 2, provided the Service Indicator

is in use for a while.

ADJUSTING TO SPECIFIC ROOM

CONDITIONS

•

Reset Service Indicator: press OFF (all leds are off).

Press PROGRAM: all user settings are saved and the air

cleaner is back in normal control.

Program Setting 1: Service Indicator

The Service Indicator is used to predict when the filter will need

cleaning (electronic air cleaners) or replacement (media air

cleaners).

Program Setting 3: Maximum fan speed for Air Quality

Analyzer (AUTO mode)

The Service Indicator automatically calculates the service

interval based on the pollution level selected and the fan speed.

If the filter becomes clogged the led • and •••• will flash each

time the air cleaner is turned on.

It is not possible to go directly to setting 3.

If the panel button (>>) and then the PROGRAM key are pressed

simultaneously before confirming setting 2, you're in setting 3

and STANDBY led will flash three times every two seconds.

Adjusting the maximum fan speed for the Air Quality Analyzer

is very convenient for meeting rooms and open plan offices.

Pollution level guidelines for establishing setting:

• LOW DUTY: general pollution without tobacco smoke

•• MEDIUM DUTY: moderate tobacco smoke concentrations

••• HEAVY DUTY: high tobacco smoke concentrations

•••• EXTREME DUTY: extremely high tobacco smoke

concentrations

•

Default: •••• (TURBO).

Press W and so on to go to the desired maximum fan speed.

Press PROGRAM: confirm setting 3 and go to setting 4.

Program Setting 4: Manual lock

To select the pollution level:

In setting 4 STANDBY led will flash four times every two seconds.

Blocking the panel button (>>), to ensure that non-authorised

people cannot control the air cleaner.

•

Press PROGRAM; you are in the program mode 1 and STANDBY

led will flash once every two seconds.

•

Default: OFF (all leds off).

Press V: led • (LOW) will light up, meaning you've set the

•

Default: unlock; no leds are burning.

Press W or V: lock; led • (LOW) is burning.

Press W or V: unlock; led • (LOW) is off.

Press PROGRAM: confirm setting 4 and go to setting 5.

pollution level to LOW DUTY.

•

Press V: led •• (MEDIUM) will light up, meaning you have set

the pollution level to MEDIUM DUTY.

Press V: led ••• (HIGH) will light up, meaning you have set

the pollution level to HEAVY DUTY.

Press V: led •••• (TURBO) will light up, meaning you have set

the pollution level to EXTREME DUTY.

If you want to go back to one of the previous pollution

levels, press W.

Press PROGRAM to confirm setting 1 and to go to setting 2.

Program Setting 5: Voltage output for maximum

efficiency (Electronic Air Cleaners only)

In setting 5 STANDBY led will flash five times every two seconds.

This setting can be used to lower the efficiency (up to 10% at

low HV). This will increase the time between cleaning intervals.

•

Default: high HV level (7600 V); leds •, •• and ••• are

burning.

0508082120/101203/C

Page 7

Owner’s manual

Technical Repair Guide

•

Press W: medium HV level (7300 V); leds • and •• are

burning.

Reset to factory default

To reset the factory default settings:

•

Press W: low HV level (7100 V); led • is burning.

Press V: to increase efficiency again up to maximum HV

level (7900 V); leds •, ••, ••• and •••• are burning.

Press PROGRAM: confirm setting 5 and go to setting 6.

Open the inlet grid, press the panel button (>>). While pressing

the panel button (>>) close the inlet grid. Release the panel

button (>>) when you hear two beeps.

Everything is now back into the default setting, except the

Service Indicator (hours in use).

•

Program Setting 6: Maximum fan speed remote control/

panel button

In setting 6 STANDBY led will flash six times every two seconds.

Adjusting the maximum fan speed for remote control/panel

button is very convenient for air cleaners installed in meeting

rooms and open plan offices.

FILTER REPLACEMENT/CLEANING

See fig. 8 on page 25

In order to open the inlet grid (i.e. access the filter components),

a narrow round screwdriver type tool will be needed (such as a

torx type). The inlet grid is secured by two mechanical clips. To

release these clips there are two access holes parallel to the

control board faceplate on the inlet grid (approx. 3½" from the

sides).

•

Default: •••• (TURBO).

Press W and so on to go to the desired maximum fan speed.

Press PROGRAM: confirm setting 6 and go to setting 7.

Insert the tool into the access holes and gently push further

through some light resistance. This will allow the clips to be

"unlocked" and thus the inlet grid will open easily.

Program Setting 7: Sensitivity adjustment Air Quality

Analyzer

In setting 7 STANDBY led will flash seven times every two

seconds.

Setting the sensitivity of the Air Quality Analyzer. The more

sensitive, the quicker the reaction to changes in pollution level.

DO NOT PULL THE DOOR OPEN WITHOUT RELEASING THE

CLIPS.

•

Default: OFF (all leds are off), meaning the lowest sensitivity

Press V: led • (LOW) will light up, meaning you've set the

pollution sensitivity to low.

press V: led •• (MEDIUM) will light up, meaning you have set

the pollution sensitivity to medium.

Press V: led ••• (HIGH) will light up, meaning you have set

the pollution sensitivity to heavy.

Press V: led •••• (TURBO) will light up, meaning you have set

the pollution sensitivity to extreme.

If you want to go back to one of the previous pollution

sensitivity, press W.

Press PROGRAM to confirm setting 7 and go to setting 8.

9.1 Prefilter replacement

The disposable prefilter can only be used once and cannot be

cleaned. Do not turn the prefilter around since it can only be

used in one flow direction.

•

9.2 Electronic filter cleaning

A crackling or snapping sound will be heard occasionally during

use of the air cleaner. This is normal and is caused by high

voltage arcing in the filter. Cleaning the electronic filter is

necessary when the crackling is heard frequently.

CAUTION

Program Setting 8: Time without high voltage after

Service (Electronic Air Cleaners only)

CELLS MAY CONTAIN SHARP EDGES.

In setting 8 STANDBY led will flash eight times every two

seconds.

Use care when servicing unit or handling cells. Failure

to do so could result in minor personal injury.

Setting a specific time for no high voltage after servicing is

useful when the filter cells are damp or condensed in winter

time. This setting will go back to default value if power is

interrupted to the air cleaner.

For maximum efficiency your air cleaner cell(s) should be

cleaned regularly. When cleaning is required the following

procedure should be used:

•

Default: OFF (all leds are off), when the air cleaner is

switched on, there's always high voltage on the cell(s).

Press V: led • (LOW) will light up, meaning you've set the

time of no high voltage to 30 minutes.

Press V: led •• (MEDIUM) will light up, meaning you've set

the time of no high voltage to 60 minutes.

Press V: led ••• (HIGH) will light up, meaning you've set the

time of no high voltage to 120 minutes.

Press V: led •••• (TURBO) will light up, meaning you've set

the time of no high voltage to 240 minutes.

If you want to go back to one of the previous time setting

levels, press W.

Cleaning the cell(s)

A Turn the air moving system OFF and disconnect the air

cleaner from power. Wait 15 seconds for the collecting

cell(s) to discharge.

B Remove the cell(s) and prefilter(s) from cabinet. Using a

solution of warm water and low sudsing detergent, soak

cell(s) for 20 to 30 minutes. Discard prefilter(s) and carbon

filter(s).

Press PROGRAM to confirm setting 8. The air cleaner will

return to the normal running mode.

NOTE: Ionizing wires may become coated causing loss of

cleaning ability by the collecting cell. Using a damp cloth,

wipe each ionizing wire, exercising care not to damage

them.

0508082120/101203/C

Page 8

Owner’s manual

Technical Repair Guide

C Remove the cell(s) from the solution and rinse thoroughly

with clean hot water water.

D Allow cell(s) to drip dry for a minimum of 2 hours. Cell(s)

may be tipped at a slight angle to expedite the drip-dry

process.

E Reinstall the cell(s) and new replacement prefilter(s) and

carbon filter(s) in the cabinet.

A moderate amount of arcing or "snapping" may occur when

the unit is turned on. This may indicate that the cell(s) are still

damp. Turn the unit off and allow it more drying time or go to

Program Setting 8.

9.3 Media filter replacement

The disposable media filter can only be used once and cannot

be cleaned. Replace as necessary.

9.4 Activated carbon or Odor Free filter replacement

The disposable activated carbon or the Odor Free filters can

only be used once and cannot be cleaned. They are located

behind the electronic/media filter. Replace as necessary.

0508082120/101203/C

Page 9

Owner’s manual

Technical Repair Guide

10 BASIC SERVICE GUIDE

The Basic Service Guide should cover most performance issues.

If after checking the items listed, the air cleaner still fails to

operate properly please contact your distributor.

Condition

Possible cause

Solution

Air cleaner inoperable.

Malfunctioning safety switch.

Properly close the extraction grid or contact your

service person.

Disconnected from power.

Faulty cord or plug.

Reconnect power.

Distributor to replace the cord or plug.

Contact your distributor for replacement parts.

Faulty hardware and/or software.

(Nearly) exhausted battery.

Poorly operating or malfunctioning

remote control.

Check the red led above the • button on the

remote control by pressing any button. Replace the

battery if the led is not activated.

Fan fails to rotate.

Defective fan.

Contact your distributor for replacement parts.

Replace or clean the filters.

Faulty hardware and/or software.

One or more filters are polluted.

Vents are closed.

Fan works but the air cleaner

functions poorly or not at all.

Open one or more of the vents (see section 5).

Clean the electronic filter.

Dirt in the electronic filter causes a short-circuit

(STANDBY led blinks)

Crackling sound from the electronic

filter.

Electronic filter dirty or wet.

Missing prefilter.

Clean or dry the electronic filter.

Install prefilter.

The air cleaner cannot be

controlled manually.

Control is locked out.

See Program Setting # 4 (page 7) to unlock.

STANDBY led blinks.

Dirt in the electronic filter causes a short-circuit.

Clean the electronic filter.

Contact your distributor.

Short-circuit in the electronic filter by a broken

ionizing wire and/or bent collector plates.

Air cleaner is in PROGRAM mode.

Push the PROGRAM button on the remote control

once or several times to scroll through the menu or

wait for 1 minute.

•••• and • leds blink.

The Service Indicator indicates that the filters are

clogged.

Clean the electronic filter or replace the media

filter.

The fan speed does not increase

when using the Air Quality

Analyzer.

Fan speed limited.

See Program Setting # 6 (page 8) to change

maximum fan speed.

The Air Quality Analyzer starts

while the atmosphere is apparently

clean.

Sensor reacts to, for instance, high or low humidity

or fumes from cleaning agents.

The sensitivity will adjust itself after some time.

Air Quality Analyzer is too sensitive.

Contact your distributor.

Smells are no longer adsorbed.

Activated carbon filter or Odor Free filter is

saturated.

Replace the activated carbon filter or Odor Free

filter.

0508082120/101203/C

Page 10

Owner’s manual

Parts List

Units where used

White-

Pos. Rodgers P/N Description

Electrical components

Price €

F849 0064 Motor + fan (120V/1ph/60Hz)

F809 0095 Capacitor 5,0 µF (120V/1ph/60Hz)

96,00

1,40

F859 0386 PC board control

F859 0387 PC board HT

F881 0241 HT transformer (120V/1ph/60Hz)

72,00

40,40

65,60

F881 0242 Transformer motor (120V/1ph/60Hz)

F881 0244 Choke 120V/60Hz Kit UV Light

30,60

25,00

10 F829 0014 Fuse 4,0 A-T (120V/60Hz)

11 F848 0389 Sensor module Air Quality Analyzer

1,44

80,40

12 F843 1398 Ionizing wires collecting cell (set of 10)

15,88

13 F848 0390 Remote control

14 F819 0160 Contact board

15 F843 1399 Flatcable

Mechanical components

15,64

6,20

1,24

16 F831 0131 Inlet grid white

17 F831 0132 Inlet grid bronze

18 F828 0212 Frame prefilter

19 F833 0023 Hinge inlet grid

20 F820 0355 Base cover white

21 F820 0356 Base cover bronze

22 F839 0020 Turning knob electronic cell

23 F828 0213 Fan protection frame

24 F820 0357 Cover fragrance gel

25 F828 0214 Frame activated carbon filter (set of 10)

28,84

44,00

2,48

0,84

7,50

11,80

0,60

2,48

0,40

24,72

Spare filters

26a F825 0630 Prefilter (72 pcs)

26b F825 0631 Prefilter (600 pcs)

27a F825 0632 Media filter (2 pcs)

27b F825 0633 Media filter (40 pcs)

28 F825 0634 Electronic cell

75,60

540,00

42,00

800,00

84,40

29a F825 0635 Activated carbon filter (72 pcs)

205,20

29b F825 0636 Activated carbon filter (625 pcs)

30a F825 0628 Activated carbon filter Odor Free (option, 2 pcs)

30b F825 0629 Activated carbon filter Odor Free (option, 48 pcs)

1.625,00

47,40

1.056,00

32 F848 0391 Fragrance gel (72 pcs)

F801 0198 Level 1 Service Kit includes: 6 Pre-filters, 1

media filter, 6 activated carbon filters

165,60

71,50

F801 0199 Level 2 Service Kit includes: 12 Pre-filters, 2

media filters, 12 activated carbon filters

F801 0200 Level 3 Service Kit includes: 18 Pre-filters, 3

media filters, 18 activated carbon filters

F801 0201 Level 4 Service Kit includes: 24 Pre-filters, 4

media filters, 24 activated carbon filters

F801 0202 Service Kit for Electronic Air Cleaners includes:

12 Pre-filters, 12 activated carbon filters

114,25

157,50

200,50

75,00

General components

33 F848 0386 Service tool for ionizing wires electronic cell

34 F810 0360 Service transport box electronic cell

F801 0194 Corner Wall Mount Hardware Kit

12,36

20,30

F801 0193 Wall mounting kit for single air cleaner (option)

F801 0196 Recessed ceiling mount kit for single air cleaner

5,20

11,00

F801 0197 Recessed ceiling mount kit for double air cleaner

16,00

F848 0384 Pedestal mount for single air cleaner (option)

F801 0195 Ceiling mount kit

64,00

5,20

0508082120/101203/C

Page 11

Owner’s manual

Parts List

OFF

PROGRAM

Replacement ionizing wires electronic cell

0508082120/101203/C

Page 12

Owner’s manual

Table des matières

INSTRUCTIONS DE SÉCURITÉ IMPORTANTES ................................................................. 13

MANUEL OPÉRATEUR .................................................................................................. 15

INTRODUCTION ............................................................................................................... 15

DESCRIPTION DU PRODUIT ............................................................................................... 15

2.1 Paquet de filtre ...............................................................................................................................15

2.2 Option ...........................................................................................................................................15

MONTAGE/INSTALLATION ................................................................................................ 15

3.1 Spécifications techniques .................................................................................................................15

3.2 Montage/installation de l’épurateur d’air .............................................................................................15

ENTRETIEN ...................................................................................................................... 15

4.1 Fréquence de remplacement/nettoyage des filtres ................................................................................15

4.2 Nettoyage de la partie extérieure de l’épurateur ...................................................................................16

COMMANDE .................................................................................................................... 16

5.1 Commande par le bouton frontal .......................................................................................................16

5.2 Commande par la télécommande .......................................................................................................16

5.3 Commande automatique (mode AUTO) ................................................................................................16

MODES DE PROGRAMMATION .......................................................................................... 16

6.1 Mode de Programmation 1: Indicateur Service ....................................................................................16

6.2 Mode de Programmation 2: Réinitialisation de l’Indicateur Service .........................................................17

REPARATION DES PANNES ............................................................................................... 17

GUIDE DE SERVICE TECHNIQUE .................................................................................... 18

AJUSTEMENT AUX CONDITIONS AMBIANTES SPÉCIFIQUES ................................................ 18

REMPLACEMENT/NETTOYAGE DES FILTRES ....................................................................... 19

9.1 Remplacement du pré-filtre ...............................................................................................................20

9.2 Nettoyage du filtre électronique ........................................................................................................20

9.3 Remplacement du filtre média ...........................................................................................................20

9.4 Remplacement du filtre à charbon actif ou du filtre Odor Free ...............................................................20

10 GUIDE DE SERVICE TECHNIQUE DE BASE ........................................................................... 21

PIÈCES DÉTACHÉES ..................................................................................................... 22

0508082120/101203/C

Page 13

Manuel opérateur

Instructions de Sécurité Importantes

Lisez et gardez cettes instructions

ATTENTION

AVERTISSEMENT

Avant d'installer et d'utiliser l'épurateur d'air, veuillez lire les

instructions du dispositif. Vous pourrez ainsi tirer le meilleur

avantage de l'épurateur d'air que vous avez sélectionné.

L'installation doit être conforme au code électrique local ou aux

autres codes applicables.

Avant d'effectuer l'installation, commencez par passer en revue et

par comprendre les codes locaux.

N'utilisez pas l'appareil en question dans un environnement

inflammable ou comportant des risques d'explosion.

Ne pas respecter à ces instructions pourrait se traduire par des

blessures personnelles graves ou par la mort.

A Lisez soigneusement le Manuel Opérateur et les Instructions

de Sécurité Importantes. Ne pas lire ces instructions, peut

se provoquer d'une panne du filtre ou d'un fonctionnement

non adéquat.

B Pour une utilisation efficace du dispositif, observez un

calendrier régulier de service technique et d'entretien.

Montage/installation

Pour réduire le risque de chocs électriques, d'incendie et de

blessures corporelles:

Suivez scrupuleusement les instructions de montage.

•

Ne pas utiliser l'épurateur d'air dans des emplacements

humides ou détrempés.

Ne pas utiliser l'épurateur d'air dans des locaux de cuisine.

Ne pas utiliser l'épurateur d'air avec des dispositifs de

contrôle de vitesse transistorisés (à semi-conducteurs),

comme un variateur.

Ne pas utiliser l'épurateur d'air à l'extérieur.

Ne pas utiliser l’épurateur d’air dans des conditions

ambiantes de plus de 95°F/35°C.

Avant que de procéder au montage, mettez l'épurateur d'air

hors tension.

•

Pour réduire le risque de chocs électriques, cet appareil est

équipé d'une fiche de mise à la terre ne pouvant être utilisée

qu'avec une prise reliée à la terre. Si le branchement est

impossible, prenez contact avec du personnel qualifié pour que

soit installée la prise de courant qui convient. N'utilisez jamais

une prise modifiée.

•

Faites usage de votre bon sens. Restez vigilant et concentrez-

vous sur votre travail. N'utilisez pas le produit si vous êtes

fatigué ou si vous vous trouvez sous l'influence de drogues,

d'alcool ou de médicaments, etc.

AVERTISSEMENT

DANGER D'ÉLECTROCUTION.

Avant d'effectuer des opérations d'entretien,

déconnectez le dispositif du réseau. Ne pas observer

cette instruction pourrait entraîner des blessures

sérieuses ou mortelles.

N'employez que les vis fournies avec le kit d'installation.

L'utilisation d'autres vis pourrait endommager l'épurateur d'air

et entraîner des risques de chocs électriques, d'incendie ou de

blessures corporelles.

AVERTISSEMENT

Lors de la fixation des accessoires de montage, évitez de forcer

les vis pour les serrer: vous risqueriez d'endommager

l'épurateur d'air ou d'obtenir une installation peu sûre (pouvant

entraîner la chute de l'épurateur d'air).

Après son installation sur le mur, ne changez pas l'épurateur de

place.

Ne tentez pas d'installer le présent dispositif, à moins que vous ne

soyez familiarisé avec les outils nécessaires, l'équipement, les

connexions utilitaires et les risques potentiels.

L'installation ne doit être effectuée que par un fournisseur de service

technique qualifié. Ne pas obéir à ce principe est susceptible de

réduire les performances de l'unité, et d'entraîner des blessures

sérieuses ou la mort.

Lorsque vous nettoyez un épurateur d'air monté au mur,

procédez avec précaution.

Utilisez exclusivement le kit de montage pour encastrement des

épurateurs d'air dans le plafond.

N'utilisez pas le châssis d'encastrement dans le plafond pour

supporter le poids de l'épurateur d'air.

ATTENTION

LES SECTIONS DU FILTRE PEUVENT PRÉSENTER

DES BORDS TRANCHANTS.

Risque d’incendie!

Soyez prudent lorsque vous soumettez le filtre à des

opérations techniques ou lorsque vous manipulez les

sections du filtre. Ne pas suivre cette instruction

pourrait se traduire par des blessures individuelles

mineures.

N'utilisez pas l'épurateur d'air dans des locaux où sont présents

des gaz inflammables.

0508082120/101203/C

Page 14

Manuel opérateur

Instructions de Sécurité Importantes

N'utilisez jamais l’épurateur d’air pour aspirer et/ou filtrer des

matières inflammables, couvants sous la cendre ou brûlants.

N'utilisez jamais le produit pour aspirer et/ou filtrer des vapeurs

agressives ou des particules abrasives.

Ne placez pas des objets sur le dessus de l'épurateur d'air.

N'utilisez pas l'appareil lorsque le fil électrique est endommagé.

Ne tirez pas sur le fil pour débrancher l'appareil. Protégez le fil

contre la chaleur, l'huile et les objets abrasifs. N'enroulez pas

un objet quelconque sur le fil. N'utilisez pas le fil pour tirer ou

charrier l'unité; n'utilisez pas le fil comme moyen de

manutention, ne le compressez pas pour le faire passer sous

une porte, évitez de le mettre en contact avec

des bords ou des coins tranchants.

Ne déplacez pas l'épurateur sans l'avoir préalablement

débranché.

0508082120/101203/C

Page 15

Manuel opérateur

Manuel Opérateur

3.2 Montage/installation de l’épurateur d’air

INTRODUCTION

L'épurateur d'air peut être installé de plusieurs manières à l'aide

de différents kits d'installation.

Dans ce manuel, vous trouverez les indications se rapportant au

montage, à l'usage et à l'entretien de l'épurateur d'air. Nous

vous conseillons de commencer votre lecture par les

Instructions de Sécurité Importantes.

•

Pour le montage mural, utilisez le kit d'installation

# F801 0193. Ce kit n'est utilisable qu'avec le modèle

simple.

DESCRIPTION DU PRODUIT

•

Pour le montage au plafond des épurateurs d’air, utilisez le

kit d’installation # F801 0195. Pour le modèle simple, vous

aurez besoin d'un seul exemplaire du kit d'installation,

tandis que le modèle double, lui, requiert l'utilisation de deux

exemplaires du même kit.

L’épurateur d’air est muni d’un Analyseur de Qualité d’Air, qui

mesure en continu la pollution de l’air ambiant et règle la vitesse

du ventilateur en conséquence. Le senseur de l’analyseur réagit

à l’encrassement gazeux se manifestant, par exemple, dans la

fumée de tabac.

•

Pour le montage encastré du modèle simple, utilisez le kit

d'installation # F801 0196. Pour le modèle double, utilisez

le kit d'installation # F801 0197.

2.1 Paquet de filtre

Voir fig. 1 sur page 25

L'air pollué est nettoyé en trois phases successives.

Aucun composant pour montage au plafond ou encastrement

dans le plafond n'est compris dans les kits proposés.

2.1.1 Pré-filtre [A]

Le pré-filtre retient les particules grossières de poussière, ainsi

que d'autres agents de pollution.

Assurez-vous de ce que les dispositifs de montage soient

effectivement capables de supporter l'effort qui leur est

demandé. Les poids des épurateurs d’air sont respectivement

d’au maximum 18 kg/39.9 livres et 34 kg/65.5 livres.

2.1.2 Filtre électronique [B]

Le filtre électronique offre un rendement élevé. Il est conçu pour

retenir les particules d'encrassement d'une grosseur supérieure

à 0,01 microns;

Si vous vous souhaitez utiliser le modèle simple sur un

piédestal, employez le kit d'installation piédestal # F848 0384.

ou (en cas du filtre média):

Utilisez les matériaux en conformité avec les indications du

manuel d'installation. Ne connectez l'épurateur d'air au réseau

électrique qu'une fois l'installation terminée.

2.1.3 Filtre média [B]

Du fait de son pliage particulier, le filtre média est doté d'une

surface active particulièrement grande, ce qui se traduit par une

faible résistance à l'air et une haute capacité de rétention de

l'encrassement.

ENTRETIEN

2.1.4 Filtre à charbon actif [C]

Le filtre à charbon actif adsorbe les odeurs désagréables.

Entretenez soigneusement votre épurateur d'air. Un épurateur

d'air mal entretenu peut présenter des risques d'incendie.

Pendant l’entretien et le nettoyage de l’appareil, l’épurateur doit

être toujours débranché.

2.2 Option

2.2.1 Odor Free

En cas qu’un filtre Odor Free à été installé, les fortes

concentrations d’odeur peuvent être réprimées. Le filtre

standard au charbon actif est remplacé par ce filtre Odor Free.

Suivez les consignes de maintenance et les conseils concernant

le remplacement des filtres.

Remplacez ou nettoyez les filtres à temps.

N'utilisez que les pièces détachées originales manufacturées

par le fabricant.

MONTAGE/INSTALLATION

3.1 Spécifications techniques

Inspectez le produit régulièrement pour vous assurer qu'il n'est

pas endommagé. Vérifiez le bon fonctionnement des dispositifs

de sécurité et, le cas échéant, exécutez immédiatement les

réparations nécessaires.

Contrôlez régulièrement le fil d'alimentation électrique. Quand

vous constatez qu'il est endommagé, faites-le remplacer par

une personne qualifiée pour ce faire.

Simple

Double

Dimensions

24.8x24.4x11.4 in.

24.8x41.3x11.4 in.

630x1050x290 mm

630x620x290 mm

Hauteur de

8.3 in.

210 mm

suspension max.

210 mm

Poids

max. 39.9 lbs.

max. 18 kg

max. 65.5 lbs.

max. 34 kg

4.1 Fréquence de remplacement/nettoyage des filtres

La fréquence à laquelle les filtres doivent être changés/nettoyés

dépend de la situation environnementale, des positions de

ventilation utilisées et de la durée d'usage de l'épurateur. Pour

en savoir plus sur la fréquence de remplacement/nettoyage,

vous pourrez faire usage de l’Indicateur Service. Voyez les

Consommation:

- électronique

- média

130 W

118 W

225 W

222 W

Voltage

115V, 60Hz

0508082120/101203/C

Page 16

Manuel opérateur

Manuel Opérateur

Modes de Programmation, mode 1.

passe à la vitesse suivante chaque seconde.

En cours de fonctionnement, il peut arriver que l'épurateur d'air

produise un bruit de crépitement. Ce bruit est normal et est dû

à une production d'étincelles. Cependant, s'il arrivait que cette

génération d'étincelles se produise plus souvent ou même

constamment, le filtre électronique doit être nettoyé.

5.2 Commande par la télécommande

Voir fig. 3 sur page 25

Indication de la vitesse du ventilateur sur la télécommande:

• LOW (basse)

•• MEDIUM (normale)

••• HIGH (élevée)

•••• TURBO (extrême)

Le remplacement/nettoyage du filtre doit être exclusivement

réalisé comme descrit dans la section Guide de Service

Technique.

Attention: Si le moteur est tourné sur la position ON, l’épurateur

d’air commencera automatiquement du STANDBY à la vitesse

TURBO pendant 1.5 seconde (démarrage vite). Il tournera ensuite

à la vitesse désirée

4.2 Nettoyage de la partie extérieure de l’épurateur

Nettoyez l'extérieur de l'appareil avec un chiffon humide.

N'utilisez jamais de détergent contenant de l'ammoniaque ou

des matières abrasives. L'appareil ne supporte pas l'emploi des

solvants organiques tel que la benzine, etc. Après détection des

produits de nettoyage utilisés, l’Analyseur de Qualité d’Air peut

avoir temporairement une réaction inhabituelle.

•

OFF: permet de désactiver l’épurateur d’air.

V et W : permet de commuter l'épurateur d'air sur une

position de ventilation respectueusement supérieure (V) et

inférieure (W).

•

AUTO: l’épurateur d’air passe à la commande automatique.

COMMANDE

5.3 Commande automatique (mode AUTO)

Voir fig. 5 sur page 25

Pour prévenir une possible surchauffe du ventilateur, ne fermez

pas toutes les grilles d’évacuation en même temps.

Voir fig. 4 sur page 25

Poussez le bouton AUTO sur la télécommande.

L’Analyseur de Qualité d’Air a besoin de 5 minutes de

réchauffage. Il est conseillé de ne pas débrancher l’épurateur

d’air de la tension électrique, pour éviter le délai de réchauffage.

Si la fonction AUTO est activé pendant cette période, la diode

sur le tableau de commande clignote. Après 5 minutes vous

entendez un bip et l’épurateur d’air fonctionnera

automatiquement.

L’épurateur d’air ne convient qu’à l’épuration de l’air des

espaces intérieurs.

L’utilisateur est responsable des dommages causés par une

mauvaise utilisation de l’épurateur. N’utilisez pas l’appareil

lorsque certaines pièces et dispositifs de sécurité sont

manquants, défectueux ou endommagés.

MODES DE PROGRAMMATION

L’épurateur d’air peut être commandé à trois façons différentes:

L'épurateur d'air est expédié, pour ce qui regarde la

programmation, avec une mode de programmation d'usine par

défaut. Les paramètres de programmation suivants vous

permettent de personnaliser l'épurateur d'air selon vos

préférences.

A Par le bouton frontal (bouton >>), pour choisir les vitesses

du ventilateur ou le mode AUTO

B Par la télécommande

C Automatiquement par l’Analyseur de Qualité d’Air (mode

AUTO)

•

Mode de Programmation 1: Indicateur Service

Mode de Programmation 2: Réinitialisation de l’Indicateur

Service

5.1 Commande par le bouton frontal

Voir fig. 2 sur page 25

Vous pouvez commander la vitesse du ventilateur par le bouton

frontal (bouton >>) sur la machine comme suit:

PROGRAM: poussez ce bouton une fois pour entrer en mode de

programmation. Si vous ne poussez aucun bouton pendant 60

secondes dans ce mode, l’épurateur d’air retournera en la

situation dernière sans confirmer la modification.

Quand le ventilateur ne tourne pas (OFF):

•

Pousez le bouton frontal (>>); la commande passe à AUTO.