Electronic Air Cleaner
Model Number
SST
SST1000
SST1400
SST1600
SST2000
OPERATING
LIGHT
ON
OFF
OWNER’S MANUAL
• Installation
• Operation
• Basic SST Service Guide
• Technical Repair Guide
• Repair Parts
Please read and familiarize yourself with the contents of this manual before
installing, operating or performing maintenance on the unit.
White-Rodgers is a division
of Emerson Electric Co.
PART NO. 37-6373F
Replaces 37-6373E
0631
A
B
C
HOW THE AIR CLEANER WORKS
Dirt particles flowing through the ducts (Figure 1) first enters
the pre-filters (A) where large particles (hair, lint, etc.) are
trapped. Smaller particles (smoke, dust, pollen, etc.) pass
through these pre-filters and enter the ionizing section (B).
Here each tiny particle receives a positive electrical charge.
These charged particles then enter the collecting section
(C). This section consists of a series of aluminum plates
which are alternately charged negative and positive.
Dirty Air In
Clean Air Out
The positive charge of the particles cause them to be
repelled by the positive plates and attracted to the negative
plates where they are collected . . . just as a magnet attracts
iron filings.
Figure 1
Clean-filtered air re-enters the supply duct system.
Carbon (Charcoal) Filters
White Dust (Lint)
Odors are gas molecules, not particles. They cannot be
removed by an Electronic Air Cleaner or by any other
filtration media designed to remove airborne particles.
However, some gases can be absorbed by an activated
carbon filter or diluted with fresh outdoor air. When odors
are present, the addition of charcoal filters will neutralize
odors, such as cooking odors, pet odors, cigar and cigarette
odors, ozone, etc. Optional charcoal filters are available for
your Air Cleaner. Refer to the parts list for the charcoal filter
part number for your Air Cleaner. Charcoal filters require
replacement. They cannot be washed. While there is no rule
of thumb for how often they should be changed, you can
use your best judgement based on the odors you perceive
in your environment.
An Electronic Air Cleaner is designed to collect two major
types of contaminants: ➀ Irritants (Pollens, Spores, Molds,
Bacteria, etc.) and ➁ Black Soiling Contaminants (Dirt and
Smoke particles).
The residue on the collecting plates of an electronic air
cleaner is black, indicating it is removing dirt from the air
stream. After installing an air cleaner you may notice white
dust (typically, long linty particles or fibers – from carpets,
cotton materials or drapery fabrics). This material is not
collected by the air cleaner because it does not contain the
irritants or soiling contaminants listed above or settles out of
the air before reaching the air cleaner. The presence of
white dust does not indicate an air cleaner requires service.
CONSTRUCTION OF THE AIR CLEANER
Not only is your air cleaner easy to install, it is also easy to
operate and maintain. Its basic components, and their
functions, are as follows: (See Figure 2)
Pre-Filters
Cabinet
Handle
Cabinet - mounts to existing duct work and houses the
collecting cells and pre-filters.
Collecting Cells - are made in two sections and perform the
actual collecting of dust, dirt, and other impurities
from the air. They contain the ionizing and collec-
tion sections described above.
Each cell must be installed with the ionizing wires
on the air entering side. Each cell must be oriented
with the handles and contact button (Figure 2)
toward the operator.
Contact
Button
Pre-filters - are in two sections which are interchangeable.
Collecting Cells
Contact
Button
They serve as a pre-filter to trap large particles
such as hair and lint before they can enter the cell
sections.
Power Pack
Figure 2
Power Pack- contains operating and power on lights as well
as the solid state components that convert the 120
volt power supply to the high-voltage, direct current
required for the collecting cell.
3
PREINSTALLATION
(Interchangeable)
Collecting Cell
(Interchangeable)
Collecting Cell
Not to Exceed 20
Outlet Box
Cabinet
Power Pack
Air Flow
Handle
Air Flow
Furnace
Opening
Contact
Button
Pre-Filters
Electronic
Air Cleaner
Opening
Contact
Button
(Interchangeable)
See text for Cell
Removal Clearance
Furnace
Electronic
Air Cleaner
Transition Section
(if Needed)
Figure 4
Knockouts for
3/4" Conduit
(three sides)
Figure 3
6 7/8"
LOCATING THE AIR FILTER
Your air filter must be mounted in the return air duct of a
central forced-air system, on the air entering side of your
furnace. (See Figure 3 for example.)
Select a location that meets the following:
C
F
E
1. The face of the cell will be at a right angle to the air
stream.
D
2. Allow the following clearances to permit removal of
cells and pre-filters: (See Figures 4 and 5)
Model SST1000 - 14 inches
Model SST1400 - 15 inches
Model SST1600 - 14 inches
Model SST2000 - 15 inches
B
A
For complete dimension data refer to Figure 5.
3. The air filter is not to be placed in the discharge of
either the heating or cooling unit.
MODEL NO.
A
B
C
D
E
F
SST1000
SST1400
SST1600
SST2000
24 3/4 21 5/16 18 5/8 13 9/16 16 7/16 19 1/16
29 11/16 26 1/4 23 5/8 13 9/16 16 7/16 19 1/16
25 1/2 21 5/16 18 5/8 17 3/4 20 5/8 23 3/8
29 11/16 26 1/4 23 5/8 17 3/4 20 5/8 23 3/8
4. IMPORTANT: If atomizing spray type humidifier is
used, it must be installed downstream from the air
filter.
5. If the air cleaner has a power cord installed, unit must
be located close enought to the outlet so connection
can be made without the use of an extension cord.
Figure 5
DIRECTION OF AIR FLOW THROUGH
If your furnace duct system has a pre-installed boot,
discard front cover of boot and slide the air cleaner
component inside the boot. For installation of Air Cleaner
Retrofit (ACR) kits, see page 13.
THE AIR CLEANER
Your air cleaner is shipped from the factory with air flow
from left-to-right. If this air flow is suitable for the
installation, no further changes need to be made (Fig-
ure 4). For right-to-left air flow, remove both pre-filter
and cell sections. Turn cells upside down (with the
same end facing the cabinet opening). This will locate
the ionizing wires at the right, and both contact buttons
and cell handles will be facing the power door. Air flow
direction must agree with arrow embossed on end of
collecting cells.
If furnace opening cannot be enlarged to required size, a
transition sheet metal section must be used. Transition
must be planned for each job. Reduction should not be
more than 4 inches per linear foot, approximately 20
angular degrees (Figure 3).
After installing the cell sections, install pre-filters in cabinet
tracks on the right. This will again place the pre-filters on
the air entering side (on the same side as ionizing wires).
4
TYPICAL MOUNTING POSITIONS
Air Flow
Air Flow
Air Flow
Rear View
Rear View
Figure 6
BASEMENT FURNACE
Figure 8
HIGHBOY FURNACE
Figure 7
COUNTERFLOW
FURNACE (Figure 7)
(LOWBOY) (Figure 6)
(Figure 8)
Cleaner is mounted hori-
zontally in return plenum,
just above furnace.
Side installation. Cleaner
is mounted vertically,
where return air enters
side inlet of furnace.
Cleaner is mounted horizontally in re-
turn duct or plenum, just above furnace.
HIGHBOY FURNACE
(Figure 9)
Installation beneath furnace.
Cleaner mounts horizontally,
where return air enters from
below. Raise furnace and in-
stall beneath base.
Less than
7 Inches
Offset
After attaching the air cleaner
cabinet to the furnace, carefully
slide or lift and place the fur-
nace into position. Do not “walk”
the furnace into position.
At Least
9 Inches
! CAUTION
▲
Walking furnace
into position could
cause damage to
Figure 10
OFFSET INSTALLATION
the air cleaner
cabinet.
(Figure 10)
Air Flow
Typical use of duct offset to match air filter opening.
Figure 9
If duct connection to furnace allows less than nine
inches for mounting the air cleaner, shorten the
lateral trunk, or attach an offset fitting to the elbow.
Air Flow
HORIZONTAL FURNACE
(Figure 11)
Cleaner is mounted vertically
in the return duct near furnace.
Figure 11
5
INSTALLATION
REMOVE OLD FILTER AND DISCARD
(Figure 12)
NOTE: This filter may be mounted in the furnace compart-
ment.
CLEAN BLOWER COMPARTMENT
It is suggested that the furnace blower compartment,
blower and blower housing be cleaned to ensure clean air
circulation.
Figure 12
Power
Supply
Box
INSTALLATION
Frame
The following is a typical installation of the air cleaner on
a “Highboy” furnace (Figure 8).
Duct
1. Place the air filter cleaner on the floor. Stand it upright
with the power door facing you (Figure 4). If a horizon-
tal installation is being planned, lay the cleaner on its
side, this will help you to visualize the relative location
of all parts.
Allow ample space for wiring and servicing the power
supply box (Figure 13).
Mounting
Holes
2. Release the latch, remove the power pack (by grasp-
ing handle and pulling power pack away from cabinet)
and set it aside. Remove the collecting cells and pre-
filters. Set pre-filters and cells aside in a safe location
until the cabinet is installed.
Figure 13
3. Set the cabinet next to the furnace. If necessary,
enlarge the opening in the furnace (if possible) to
match the opening in the cabinet.
Turning
Vanes
Air Flow
If the furnace opening cannot be enlarged, a transition
fitting should be used. (Figure 3).
The cabinet can be attached directly (Figure 13), or a
starting collar can first be fitted to the furnace inlet. A
butt or slip joint can be used.
Securely attach the cabinet to furnace inlet, using at
least two of the mounting holes on each side of the
cabinet.
Figure 14
4. Using butt joint, attach duct work (normally an elbow)
to the upstream side of air cleaner cabinet. (Note the
use of the sheet metal turning vanes inside the elbow
to improve air distribution over the face of the cells.)
(Figure 14)
NOTE: An optional method of attaching duct work to the
Optional method
(Bend tabs outward at 90˚ angle)
cabinet is to modify the cabinet (Figure 15) by bending the
tabs outward at a 90° angle and attaching duct work to
tabs.
Figure 15
5. Connect the vertical duct section to the elbow. Wedge
a wood block between floor and elbow for support
(Figure 16).
Transition Fittings
If the air duct does not fit the cabinet opening, a transition
fitting should be used. Gradual transitions are preferred
for greatest efficiency. Not more than four inches per
linear foot (approximately 20° angle) should be allowed
(Figure 3).
6. Seal all joints in the return air system downstream
from the air cleaner with duct tape to prevent dust from
entering the air stream. Tape is usually applied on the
outside of ducts, but may also be applied on the
inside, or both.
6
WIRING INSTRUCTIONS
7. With the cabinet installed, the air cleaner can now be 10. If this unit has an electrical cord, the cord has a
wired to electrical input source.
grounding type plug with a third (grounding) pin. This
plug will fit only into a grounding type power outlet. If
the proper type of outlet is not available, contact
qualified personnel to install a proper outlet. Do not
alter the plug in any way.
!
WARNING
Installation of this unit must comply with local
electric codes or other applicable codes.
Review and understand local codes prior to instal-
lation.
! WARNING
▲
To reuce the risk of electric shock, The power cord
must be connected to an appropriate outlet. Do not
alter the plug in any way.
injury or death.
Failure to do so could result in serious personal
8. An air cleaner unit with no air flow monitor requires 11. With the cabinet Installed, reinstall pre-filter(s) and
electrical wiring through the furnace controls. Con-
nect wiring to the furnace control terminals (EAC-H)
for power, (EAC-N) for neutral and connect metal
frame of EAC to ground.
collecting cell(s) (Figure 18).
NOTE: The contact button and handles on the cell
must be facing you and ionizing wires must be on the
air intake side.
If the air cleaner unit has an air flow monitor, it must be
connected to 120 VAC 60 Hz. A 20 amp circuit is more
than adequate. If an air flow monitor is not installed but
is required for operation, order Air Flow Kit F859-
0381. If a power cord is required, order F97-0019.
12. Install the power pack as follows:
Engage the lip on lower inside edge of power pack in
the flange on cabinet and carefully close the power
pack,makingsurethattheelectricalconnectorprongs
on the power pack enter the slots in the socket on
cabinet.Whenthepowerpackisfullyinplace,engage
the latch and snap it closed.
9. Remove junction box cover and install the required
bushing into the 3/4 in. Knock out. With the supply
voltage turned off, route three (3) wires into junction
box for connections. (See Fig. 17.)
Pre-Filters
Cabinet
Handle
Insure all wires are clamped, wire connectors prop-
erly installed and grommets used to prevent wire
abrasion.
Vertical
Section
Contact
Button
Tape All
Joints
Collecting Cells
Contact
Button
Power Pack
Figure 18
Latch
To Engage
Wood Block
Press to Close After
Latch is Engaged
Figure 16
Female Plug
Male Plug
Hot
Cabinet
Neutral
Side Edge of
Power Pack
Grounding
Conductor
Power Pack
Front View
Figure 17
Engage Lip on Lower Inside Edge
of Power Pack in Flange.
Figure 19 Installing Power Pack
7
OPERATION
1. With the 120 VAC power turned on at the circuit
breaker for the furnace, push the air cleaner ON-OFF
switch to the “ON” position (Figure 20).
2. With the furnace blower running, the air cleaner will be
operating. An arcing or “snapping” sound may be
heard. This will occur occasionally, however the unit
is operating properly.
3. With the furnace blower running, the Operating Light
should be ON. If the Operating Light is not ON this
signifies that the cells need washing, or that trouble
exists in the unit.
Operating
Light
If, after washing the cells, the Operating Light stays off, the
cell could be wet, improperly placed in the cabinet or may
need servicing.
On-Off
Switch
NOTE: An occasional flicker of the light accompanied by
harmless sparking or snapping noise may occur. This is
caused by trapping large particles of dirt. If arcing is
continuous, the cells should be washed or checked for
service problems see Basic SST Service Guide.
Figure 20
4. Remove the cell(s) and pre-filter(s) from cabinet.
Using a solution of warm water and low sudsing
detergent, soak cell(s) and pre-filter(s) for 20 to 30
minutes.
MAINTENANCE AND WASHING
!
CAUTION
NOTE: Ionizing wires may become coated causing
CABINET AND CELLS MAY CON-
TAIN SHARP EDGES.
loss of cleaning ability by the collecting cell. Using a
damp cloth, wipe each ionizing wire, exercising care
not to damage them.
Use care when servicing unit or han-
5. Remove the cell(s) and pre-filter(s) from solution and
rinse thoroughly with clean water.
dling cells.
Failure to do so could result in minor
personal injury.
6
Allow cell(s) and pre-filter(s) to drip dry for a minimum
of 2 hours. Cell(s) and pre-filter(s) may be tipped at
a slight angle to expedite the drip-dry process.
For maximum efficiency your air cleaner cell(s) and pre-
filter(s) should be inspected once a month and cleaned
when necessary. Cleaning will usually be required every
one to three months, depending upon the particular house-
hold circumstances. When cleaning is required the follow-
ing procedure should be used:
7. Reinstall the cell(s) and pre-filter(s) in the cabinet.
8. Replace the power pack. Turn furnace fan on. After 30
minutes push ON-OFF switch on the power pack to
the “ON” position.
A moderate amount of arcing or “snapping” may occur
at this time, which will indicate that the cell(s) are still
damp. If the noise is objectionable, push the ON-OFF
switch to the “OFF” position and allow additional time
for cell(s) and pre-filter(s) to dry. In some cases the
Operating Light will remain OFF during this initial
activation of the air cleaner, and this would indicate
that the cell(s) are not completely dry. The Operating
Light should remain ON while the furnace fan is
running once the drying is complete.
CLEANING THE CELLS
1. Turn the air moving system “OFF.”
2. Push the ON-OFF switch on the power pack to the
“OFF” position (Figure 20). Wait 15 seconds and both
the power pack and the collecting cell(s) will be
automatically discharged.
3. Release the latch on top of power pack and pull the
power pack straight away from cabinet at the top.
Then lift pack out of ledge at bottom edge of cabinet.
Set power pack aside.
8
REPLACING AN IONIZING WIRE
If an ionizing wire should break, it can be replaced as
follows:
1. Remove all pieces of broken wire. Make sure sup-
ports at each end are in good condition and not bent
out of shape.
2. Hook the new wire onto the support at one end.
3. Hold your finger against the support at the other end
(Figure 21) and hold the ionizing wire between thumb
and forefinger as shown or use needle nose pliers.
Press inward on spring support. Hook end of wire over
small tab at end of support and release. Make sure
wire is securely anchored at each end.
Support
Ionizing
Wire
Figure 21
SPECIFICATIONS
SPECIFICATIONS
SST1000
SST1400
SST1600
SST2000
Rated Capacity
Max. Pressure Drop
Cell Weight
600 - 1200 cfm
.08 in. W.G.
(2) 7 lbs. each
9 lbs.
1000 - 1600 cfm
.08 in. W.G.
(2) 9 lbs. each
9 lbs.
1000 - 2000 cfm
.12 in. W.G.
(2) 9 lbs. each
10 lbs.
1600 - 2200 cfm
.09 in. W.G.
(2) 9 lbs. each
10 lbs.
Power Pack Weight
Unit Weight
35 lbs.
42 lbs.
38 lbs.
45 lbs.
Power Consumption
Electrical Input
40 Watts (Max)
120 VAC 60 hz.
1.0 Ma
40 Watts (Max)
120 VAC 60 hz.
1.2 Ma
40 Watts (Max)
120 VAC 60 hz.
1.5 Ma
40 Watts (Max)
120 VAC 60 hz.
1.7 Ma
Electrical Output
@ 6450 VDC (nom)
Max. Ozone Output
Temperature Rating
.05 ppm
.05 ppm
.05 ppm
.05 ppm
40 F to 125 F
40 F to 125 F
40 F to 125 F
40 F to 125 F
9
SERVICE CHECKS
BASIC SST SERVICE GUIDE
This guide will cover most homeowner complaints. If, after checking the items listed, the unit still fails to operate
properly, contact the nearest Authorized Service Center.
SERVICE INDICATION
Unit functioning Normally
ON/OFF switch “ON”
Blower ON
Operating Light ON
ON/OFF switch “ON”
Blower ON
1. Power is not being supplied to air cleaner.
A. Check fuse or circuit breaker.
Operating Light OFF
B. Ensure power pack is properly installed and latched.
2. Collecting cell shorted - Turn power Off - Remove power pack - Remove
collecting cells - Replace power pack - Restore power (ensure blower is
operating).
A. If Operating Light comes ON check cells for bent plates, loose ionizing
wire(s) or cracked insulator(s).
B. If Operating Light remains OFF, malfunction is in the power pack. (See
power supply Checkout Procedure).
ON/OFF Switch “ON”
Blower OFF
Operating Light ON
1. Air flow sensor contaminated/misaligned
A. Remove power pack and clear contamination inside black bushing around
the small sensor element.
B. Ensure small sensor element is centered in bushing.
2. Air sensor left in bypassed condition after servicing.**
3. Faulty air flow sensor panel.
Excessive arcing during
normal operation -
Operating Light may blink
1. Wet collecting cell.
A. Allow cell(s) to dry after cleaning before applying power.
2. Damaged collecting cell(s).
A. Remove cell(s) and inspect for bent plates, loose ionizing wire(s), cracked
insulator(s), etc.
3. Collecting cells dirty.
A. Clean cells as instructed in this manual.
4. Faulty power supply (see power supply checkout procedure)
**NOTE: Your air cleaner may be equipped with an air flow sensor (switch) which turns the unit ON and OFF in
response to the system blower. It may have been “wired out” during a service check and inadvertently left in this
condition.
10
TECHNICAL REPAIR GUIDE
All voltage measurements indicated can be made with a
high voltage D.C. probe and a general purpose volt ohm
meter. For example: Simpson 260 or equivalent.
!
WARNING
Do not attempt repair of this unit unless you are
connections and potential hazards.
familiar with the necessary tools, equipment, utility
For test purposes, the air flow switch may be “wired out”
of the system. This will eliminate the need for air flow
across the sensing thermistor to energize the power
supply (see Fig 23).
Repair should be performed only by a qualified
service provider.
NOTE: All tests to be performed with the Ozone Reduction
Jumper intact.
Failure to do so could result in reduced perfor-
mance of the unit, serious personal injury or death.
NOTE: When servicing the power pack components, all
wiring must be routed to factory specifications.
This guide contains service checks to assist service
personnel in locating and correcting any malfunction that
might occur to render the air cleaner ineffective or inop-
erative. The air cleaner has been designed with replace-
able components, such as the high-voltage power supply
and air flow switch. This allows the serviceman to replace
a faulty component rather than attempt repairs of such
components in the field.
Power Pack
Assembly
120 VAC
Cover Assembly
Connector
L1
L2
Power Supply
Specifications
Wht
Wht
Wht from L2 or Wht/Brn from Air Flow
The solid-state power supply is not
designed for individual component part
replacement and must be replaced as
a complete "snap-in" unit.
Operating
Light
(If Required)
Airflow Switch
ON/OFF
Switch
Input voltage: 120 VAC 60 Hz.
Output to light: 1.5 to 2.5 VDC
H.V. Output: 6450 VDC (nom)
Blk
Blk
Red
Collecting Cell
Specifications
Gnd
Cell Contact
& Insulator
1000 cfm - 1.0 Ma @ 6450VDC
1400 cfm - 1.2 Ma @ 6450 VDC
1600 cfm - 1.5 Ma @ 6450 VDC
2000 cfm - 1.7 Ma @ 6450 VDC
Power
Supply
Wht
Blu
Wht or Wht/Brn*
Blk
*Wht from L2 or Wht/Brn from Air Flow
Figure 22
11
4. Using a standard extension cord, apply 120 VAC to
power pack. Turn power switch to “ON” position.
POWER SUPPLY
CHECKOUT PROCEDURE
5. Connect meter negative (-) lead to metal frame of
collecting cell. Use high voltage probe to measure
voltage at collecting cell ionizer or cell plates. Voltage
should be 6100 to 6800 VDC.
1. Turn power switch to the “OFF” position and remove
the power pack from cabinet.
2. If air flow switch is installed, locate air flow switch and
remove power pack cover. If air flow switch is not
installed, go to step 4.
NOTE: A new “out-of-box” cell may cause the voltage
to be lower than normal for a short period of time. To
obtain a more accurate measurement, “age” the cell
by applying high voltage to the cell for 15 to 30
minutes.
3. Disconnect the three-pin plastic connector and jumper
the two female pins (white wire to white-brown wire)
as shown in Fig. 23.
6
If voltage is below 6100 VDC, check cell for foreign
objects, bowed/bent/loose plates, broken ionizing
wires or cracked insulators. Wash cells if required. If
Operating Light remains OFF, replace collecting cell.
Plastic Connector
Male Pin
AIR FLOW MONITOR TEST
Jumper Lead
Female Pins
1. Connect a multimeter set to read 120 VAC to power
supply terminals marked “LINE.”
Method of jumping lead wires of
connector plug from air flow switch.
2. Connect 120 VAC to power pack plug, turn power
switch “ON.”
Figure 23
3. Blow on thermistor at air flow monitor. 120 VAC
should appear at multimeter. Stop blowing and volt-
age should disappear in 10 - 15 seconds.
4. Place power pack on a well insulated workbench.
Connect meter negative (-) lead to the sheet metal
chassis and the high voltage probe to high voltage
contact on back cover of power pack. Connect AC
power to power pack using an extension cord and turn
power switch to the “ON” position. Keep hands and
4. If voltage did not appear (Step 3), disconnect power to
power pack. Locate air flow switch and remove power
pack cover. Disconnect the three-pin plastic connec-
tor. Jumper the two female pins (white wire to white-
brown wire) as shown in Fig. 23. Reconnect power to
power pack. Turn power switch “ON.”
tools away from high voltage contact.
5. If Operating Light comes ON and output voltage is
between 6100 and 6800 VDC, power supply is good.
A. If 120 VAC appears at multimeter, replace air flow
monitor.
6. If voltage is good but Operating Light does not come
on, replace Operating Light.
B. If 120 VAC does not appear on multimeter, prob-
lem is other than air flow monitor. Recheck all
primary wiring.
CELL TEST
NOTE: The air flow monitor is designed to operate in the
temperature range of 65° to 120° F. Operation outside this
range is not recommended.
1. Place collecting cell on a well insulated workbench
with the cell contact button pointing upward.
2. Select a power pack (with air flow switch bypassed
and ozone reduction jumper intact) that reads be-
tween 6100 and 6800 VDC at the cell contact with no
cell attached.
3. Place power pack on top of collecting cell ensuring
that there is proper contact between the cell contact
on the power pack contact.
12
OZONE REDUCTION
All electronic air cleaners typically produce a small
amount of ozone that is within established limits.
Some customers may notice an odor especially at
high altitudes or low air flow rates.
W1
This power supply has a “hairpin” shaped jumper
wire labeled W1 (see Fig 24) that can be cut and
separated in case of such complaints. This will
cause the power supply to limit the maximum
operating power to a lower level.
Cut and separate
Ozone Reduction
Jumper
WHT/BRN
E3
BLK
E2
LINE
Ozone Reduction Jumper
Figure 24
ELECTRONIC AIR CLEANER RETROFIT (ACR) KITS
INSTALLATION
Pre-Filters
Cabinet
Handle
1. Remove the two pre-filters from the package and
insert into cabinet tracks opposite the furnace. These
will be used to catch the larger particles that are in the
air stream before entering the collecting cell.
2. Insert the two collecting cells into the cabinet behind
the pre-filters. Be sure ionizing wires are directly
behind the pre-filters so the particles can be charged
as soon as the air leaves the pre-filters.
3. Remove cover plate on the power supply junction box
and remove the knockout needed to bring the wire to
the female receptacle.
Contact
Button
4. Position receptacle with ground in the down position
as shown in Fig 17 (page 7) and pull wires through the
receptacle locator on the junction box. Snap the
receptacle into the hole until secure.
Collecting Cells
Contact
Button
5. Connect ground wire from receptacle and ground wire
in kit to cabinet with rivet and washer as follows:
a) Place washer on rivet
b) Place terminal from ground wire on rivet
c) Place terminal from receptacle ground wire on
rivet
d) Insert rivet in hole in junction box and secure.
WIRING
5. For wiring installation (see page 7) and follow all
wiring instructions 7, 8 and 9.
6. Install the power pack (see page 7) instruction 11.
7. For operation (see page 8 – Operation).
13
REPAIR PARTS
15
18
14
REPAIR PARTS
PARTS LIST FOR ELECTRONIC AIR CLEANERS
When ordering repair parts, always give the following information as
shown in this list.
1. The PART NUMBER
2. The PART DESCRIPTION
3. The MODEL NUMBER
4. The NAME OF ITEM - Electronic Air Cleaner.
Always order by “PART NUMBER” . . . Not by “ITEM NUMBER”
PART NUMBER
ITEM
NO.
DESCRIPTION
SST1000
SST1400
SST1600
SST2000
1
2
3
4
5
6
7
Cabinet
N/A
N/A
N/A
N/A
Pre-Filter
•F825-0431
•F811-0398
F838-0072
------
• F825-0432
• F811-0397
F838-0072
------
• F825-0337 • F825-0338
• F811-0321 • F811-0319
Collecting Cell
Junction Box Cover
* Screw #6 x 3/8
F838-0072
------
F838-0072
------
Connector, Female
Power Pack Assembly without Air Flow
Power Pack Assembly with Air Flow
Cell Handle
F818-0053
F858-1021
F858-1031
F832-0039
F843-0484
F844-0130
F876-0202
N/A
F818-0053
F858-1022
F858-1032
F832-0039
F843-0484
F844-0130
F876-0202
N/A
F818-0053
F858-1023
F858-1033
F832-0039
F843-0500
F844-0130
F876-0202
N/A
F818-0053
F858-1024
F858-1034
F832-0039
F843-0500
F844-0130
F876-0202
N/A
8
9
Ionizing Wire
10
11
12
13
14
15
16
17
18
Light
Switch
Power Pack, Cabinet Only
Connector, Male
F827-0026
F858-1002
F16-8520
37-6373
F827-0026
F858-1002
F16-8520
37-6373
F827-0026
F858-1002
F16-8521
37-6373
F827-0026
F858-1002
F16-8521
37-6373
Power Supply
Cover, Power Pack
† Manual
† Charcoal Filter (with mounting clips)
Air Flow Switch (monitor kit)
F825-0466
F859-0381
• F825-0467
F859-0381
• F825-0468 • F825-0469
F859-0381 F859-0381
* Standard Hardware Item
• Two (2) Required
† Not Shown
15
WASH REMINDER SCHEDULE
frequent washing may be necessary on some installations
A regular washing schedule is necessary to ensure proper where there is new carpeting, plaster dust or excessive
efficiency. A thorough washing once every month will be cigarette smoke, etc. (See page 8 for maintenance and
adequate for most installations. More or Less
instructions on how to clean a cell.)
Year
JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
20___
20___
20___
20___
20___
20___
20___
20___
20___
20___
20___
20___
NOTICE TO CONSUMERS
White-Rodgers
Electronic Air Cleaner
Dear Consumer;
White-RodgerswouldliketothankyouforpurchasingaWhite-RodgersElectronicAirCleaner
orproductcontainingaWhite-RodgersElectronicAirCleaner. AlthoughWhite-Rodgersdoes
not extend a warranty directly to consumers, White-Rodgers does extend a warranty to
Wholesalers and Original Equipment Manufacturers who use White-Rodgers Products. To
obtain more information about how your Wholesaler or Original Equipment Manufacturer’s
warranty may benefit you, please contact your Wholesaler or Original Equipment Manufac-
turer.
Sincerely,
White-Rodgers
The Emerson logo is
trademark and a service mark
of Emerson Electric Co.
|