AIR CONDITIONER (SPLIT TYPE)
Installation Manual
Indoor Unit
Model name:
Concealed Duct High Static Pressure Type
RAV-SM2242DT-E
RAV-SM2802DT-E
Installation Manual
Air conditioner (Split type)
English
Français
Deutsch
Italiano
Español
1
41
81
Manuel d’installation
Climatiseur (Type split)
Installationsanleitung
Klimagerät (Split-typ)
Manuale di installazione
Condizionatore d’aria (Tipo split)121
Manual de instalación
Aire acondicionado (Tipo split) 161
Installation Manual
Concealed Duct High Static Pressure
Thank you for purchasing this Toshiba air conditioner.
Please read carefully through these instructions that contain important information which complies with the “Machinery”
Directive (Directive 2006/42/EC), and ensure that you understand them.
Some of the details provided in these instructions differ from the Installation Manual supplied with your product, and the
instructions provided here take precedence.
After reading these instructions, be sure to keep them in a safe place together with the Owner’s Manual and Installation Manual
supplied with your product.
Generic Denomination: Air Conditioner
Definition of Qualified Installer or Qualified Service Person
The air conditioner must be installed, maintained, repaired and removed by a qualified installer or qualified service person.
When any of these jobs is to be done, ask a qualified installer or qualified service person to do them for you.
A qualified installer or qualified service person is an agent who has the qualifications and knowledge described in the table
below.
Agent
Qualifications and knowledge which the agent must have
• The qualified installer is a person who installs, maintains, relocates and removes the air conditioners made
by Toshiba Carrier Corporation. He or she has been trained to install, maintain, relocate and remove the air
conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such
operations by an individual or individuals who have been trained and is thus thoroughly acquainted with the
knowledge related to these operations.
• The qualified installer who is allowed to do the electrical work involved in installation, relocation and removal
has the qualifications pertaining to this electrical work as stipulated by the local laws and regulations, and
he or she is a person who has been trained in matters relating to electrical work on the air conditioners made
by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such matters by an
individual or individuals who have been trained and is thus thoroughly acquainted with the knowledge
related to this work.
Qualified installer
• The qualified installer who is allowed to do the refrigerant handling and piping work involved in installation,
relocation and removal has the qualifications pertaining to this refrigerant handling and piping work as
stipulated by the local laws and regulations, and he or she is a person who has been trained in matters
relating to refrigerant handling and piping work on the air conditioners made by Toshiba Carrier Corporation
or, alternatively, he or she has been instructed in such matters by an individual or individuals who have been
trained and is thus thoroughly acquainted with the knowledge related to this work.
EN
• The qualified installer who is allowed to work at heights has been trained in matters relating to working at
heights with the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been
instructed in such matters by an individual or individuals who have been trained and is thus thoroughly
acquainted with the knowledge related to this work.
• The qualified service person is a person who installs, repairs, maintains, relocates and removes the air
conditioners made by Toshiba Carrier Corporation. He or she has been trained to install, repair, maintain,
relocate and remove the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she
has been instructed in such operations by an individual or individuals who have been trained and is thus
thoroughly acquainted with the knowledge related to these operations.
• The qualified service person who is allowed to do the electrical work involved in installation, repair,
relocation and removal has the qualifications pertaining to this electrical work as stipulated by the local laws
and regulations, and he or she is a person who has been trained in matters relating to electrical work on the
air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she has been instructed in such
matters by an individual or individuals who have been trained and is thus thoroughly acquainted with the
knowledge related to this work.
Qualified service
person
• The qualified service person who is allowed to do the refrigerant handling and piping work involved in
installation, repair, relocation and removal has the qualifications pertaining to this refrigerant handling and
piping work as stipulated by the local laws and regulations, and he or she is a person who has been trained
in matters relating to refrigerant handling and piping work on the air conditioners made by Toshiba Carrier
Corporation or, alternatively, he or she has been instructed in such matters by an individual or individuals
who have been trained and is thus thoroughly acquainted with the knowledge related to this work.
• The qualified service person who is allowed to work at heights has been trained in matters relating to
working at heights with the air conditioners made by Toshiba Carrier Corporation or, alternatively, he or she
has been instructed in such matters by an individual or individuals who have been trained and is thus
thoroughly acquainted with the knowledge related to this work.
– 2 –
2-EN
Installation Manual
Concealed Duct High Static Pressure
Definition of Protective Gear
When the air conditioner is to be transported, installed, maintained, repaired or removed, wear protective gloves and ‘safety’
work clothing.
In addition to such normal protective gear, wear the protective gear described below when undertaking the special work detailed
in the table below.
Failure to wear the proper protective gear is dangerous because you will be more susceptible to injury, burns, electric shocks
and other injuries.
Work undertaken
Protective gear worn
Protective gloves
‘Safety’ working clothing
All types of work
Gloves to provide protection for electricians and from heat
Insulating shoes
Clothing to provide protection from electric shock
Electrical-related
work
Work done at heights
(50 cm or more)
Helmets for use in industry
Transportation of
heavy objects
Shoes with additional protective toe cap
Repair of outdoor unit Gloves to provide protection for electricians and from heat
3-EN
– 3 –
Installation Manual
Concealed Duct High Static Pressure
Warning Indications on the Air Conditioner Unit
Warning indication
Description
WARNING
WARNING
ELECTRICAL SHOCK HAZARD
Disconnect all remote electric power supplies before servicing.
ELECTRICAL SHOCK HAZARD
Disconnect all remote
electric power supplies
before servicing.
WARNING
WARNING
Moving parts.
Moving parts.
Do not operate unit with grille removed.
Stop the unit before the servicing.
Do not operate unit with grille
removed.
Stop the unit before the servicing.
CAUTION
CAUTION
EN
High temperature parts.
You might get burned
when removing this panel.
High temperature parts.
You might get burned when removing this panel.
CAUTION
CAUTION
Do not touch the aluminum
fins of the unit.
Doing so may result in injury.
Do not touch the aluminium fins of the unit.
Doing so may result in injury.
CAUTION
CAUTION
BURST HAZARD
Open the service valves before
the operation, otherwise there
might be the burst.
BURST HAZARD
Open the service valves before the operation, otherwise there might be the
burst.
– 4 –
4-EN
Installation Manual
Concealed Duct High Static Pressure
1 PRECAUTIONS FOR SAFETY
WARNING
General
• Before starting to install the air conditioner, read carefully through the Installation Manual, and follow its instructions to install
the air conditioner.
• Only a qualified installer(*1) or qualified service person(*1) is allowed to install the air conditioner. If the air conditioner is
installed by an unqualified individual, a fire, electric shocks, injury, water leakage, noise and/or vibration may result.
• Before opening the intake grille of the indoor unit or service panel of the outdoor unit, set the circuit breaker to the OFF
position. Failure to set the circuit breaker to the OFF position may result in electric shocks through contact with the interior
parts. Only a qualified installer(*1) or qualified service person(*1) is allowed to remove the intake grille of the indoor unit or
service panel of the outdoor unit and do the work required.
• Before carrying out the installation, maintenance, repair or removal work, be sure to set the circuit breaker to the OFF
position. Otherwise, electric shocks may result.
• Place a “Work in progress” sign near the circuit breaker while the installation, maintenance, repair or removal work is being
carried out. There is a danger of electric shocks if the circuit breaker is set to ON by mistake.
• Only a qualified installer(*1) or qualified service person(*1) is allowed to undertake work at heights using a stand of 50 cm
or more or to remove the intake grille of the indoor unit to undertake work.
• Wear protective gloves and safety work clothing during installation, servicing and removal.
• Do not touch the aluminium fin of the outdoor unit. You may injure yourself if you do so. If the fin must be touched for some
reason, first put on protective gloves and safety work clothing, and then proceed.
• Do not climb onto or place objects on top of the outdoor unit. You may fall or the objects may fall off of the outdoor unit and
result in injury.
• When working at heights, use a ladder which complies with the ISO 14122 standard, and follow the procedure in the ladder’s
instructions. Also wear a helmet for use in industry as protective gear to undertake the work.
• When cleaning the filter or other parts of the outdoor unit, set the circuit breaker to OFF without fail, and place a “Work in
progress” sign near the circuit breaker before proceeding with the work.
• When working at heights, put a sign in place so that no-one will approach the work location, before proceeding with the
work. Parts and other objects may fall from above, possibly injuring a person below.
• The refrigerant used by this air conditioner is the R410A.
• You shall ensure that the air conditioner is transported in stable condition.
• Do not move or repair any unit by yourself. There is high voltage inside the unit. You may get electric shock when removing
the cover and main unit.
Selection of installation location
• If you install the unit in a small room, take appropriate measures to prevent the refrigerant from exceeding the limit
concentration even if it leaks. Consult the dealer from whom you purchased the air conditioner when you implement the
measures. Accumulation of highly concentrated refrigerant may cause an oxygen deficiency accident.
• Do not install the air conditioner in a location that may be subject to a risk of exposure to a combustible gas. If a combustible
gas leaks and becomes concentrated around the unit, a fire may occur.
• When transporting the air conditioner, wear shoes with additional protective toe caps.
• When transporting the air conditioner, do not take hold of the bands around the packing carton. You may injure yourself if
the bands should break.
• Install the indoor unit at least 2.5 m above the floor level since otherwise the users may injure themselves or receive electric
shocks if they poke their fingers or other objects into the indoor unit while the air conditioner is running.
• Do not place any combustion appliance in a place where it is directly exposed to the wind of air conditioner, otherwise it may
cause imperfect combustion.
Installation
• When the indoor unit is to be suspended, the designated hanging bolts (M10 or W3/8) and nuts (M10 or W3/8) must be used.
• Install the air conditioner at enough strong places to withstand the weight of the unit. If the strength is not enough, the unit
may fall down resulting in injury.
• Follow the instructions in the Installation Manual to install the air conditioner. Failure to follow these instructions may cause
the product to fall down or topple over or give rise to noise, vibration, water leakage, etc.
• The designated bolts (M10, M12) and nuts (M10, M12) for securing the outdoor unit must be used when installing the unit.
• Install the outdoor unit property in a location that is durable enough to support the weight of the outdoor unit. Insufficient
durability may cause the outdoor unit to fall, which may result in injury.
5-EN
– 5 –
Installation Manual
Concealed Duct High Static Pressure
Refrigerant piping
• Install the refrigerant pipe securely during the installation work before operating the air conditioner. If the compressor is
operated with the valve open and without refrigerant pipe, the compressor sucks air and the refrigeration cycles is over
pressurized, which may cause a injury.
• Tighten the flare nut with a torque wrench in the specified manner. Excessive tighten of the flare nut may cause a crack in
the flare nut after a long period, which may result in refrigerant leakage.
• After the installation work, confirm that refrigerant gas does not leak. If refrigerant gas leaks into the room and flows near a
fire source, such as a cooking range, noxious gas may be generated.
• When the air conditioner has been installed or relocated, follow the instructions in the Installation Manual and purge the air
completely so that no gases other than the refrigerant will be mixed in the refrigerating cycle. Failure to purge the air
completely may cause the air conditioner to malfunction.
• Nitrogen gas must be used for the airtight test.
• The charge hose must be connected in such a way that it is not slack.
• If refrigerant gas has leaked during the installation work, ventilate the room immediately. If the leaked refrigerant gas comes
in contact with fire, noxious gas may be generated.
Electrical wiring
• Only a qualified installer(*1) or qualified service person(*1) is allowed to carry out the electrical work of the air conditioner.
Under no circumstances must this work be done by an unqualified individual since failure to carry out the work properly may
result in electric shocks and/or electrical leaks.
• When connecting the electrical wires, repairing the electrical parts or undertaking other electrical jobs, wear gloves to
provide protection for electricians and from heat, insulating shoes and clothing to provide protection from electric shocks.
Failure to wear this protective gear may result in electric shocks.
• Use wiring that meets the specifications in the Installation Manual and the stipulations in the local regulations and laws. Use
of wiring which does not meet the specifications may give rise to electric shocks, electrical leakage, smoking and/or a fire.
• Be sure to connect earth wire. (Grounding work)
Incomplete grounding causes an electric shock.
• Do not connect ground wires to gas pipes, water pipes, and lightning rods or ground wires for telephone wires.
• After completing the repair or relocation work, check that the ground wires are connected properly.
• Install a circuit breaker that meets the specifications in the installation manual and the stipulations in the local regulations
and laws.
EN
• Install the circuit breaker where it can be easily accessed by the agent.
• When installing the circuit breaker outdoors, install one which is designed to be used outdoors.
• Under no circumstances must the power cable be extended. Connection trouble in the places where the cable is extended
may give rise to smoking and/or a fire.
• Electrical wiring work shall be conducted according to law and regulation in the community and installation manual.
Failure to do so may result in electrocution or short circuit.
Test run
• Before operating the air conditioner after having completed the work, check that the electrical parts box cover of the indoor
unit and service panel of the outdoor unit are closed, and set the circuit breaker to the ON position. You may receive an
electric shock if the power is turned on without first conducting these checks.
• When you have noticed that some kind of trouble (such as when an error display has appeared, there is a smell of burning,
abnormal sounds are heard, the air conditioner fails to cool or heat or water is leaking) has occurred in the air conditioner,
do not touch the air conditioner yourself but set the circuit breaker to the OFF position, and contact a qualified service
person. Take steps to ensure that the power will not be turned on (by marking “out of service” near the circuit breaker, for
instance) until qualified service person arrives. Continuing to use the air conditioner in the trouble status may cause
mechanical problems to escalate or result in electric shocks, etc.
• After the work has finished, be sure to use an insulation tester set (500V Megger) to check the resistance is 2 M! or more
between the charge section and the non-charge metal section (Earth section). If the resistance value is low, a disaster such
as a leak or electric shock is caused at user’s side.
• Upon completion of the installation work, check for refrigerant leaks and check the insulation resistance and water drainage.
Then conduct a test run to check that the air conditioner is operating properly.
Explanations given to user
• Upon completion of the installation work, tell the user where the circuit breaker is located. If the user does not know where
the circuit breaker is, he or she will not be able to turn it off in the event that trouble has occurred in the air conditioner.
• If you have discovered that the fan grille is damaged, do not approach the outdoor unit but set the circuit breaker to the OFF
position, and contact a qualified service person(*1) to have the repairs done. Do not set the circuit breaker to the ON position
until the repairs are completed.
• After the installation work, follow the Owner’s Manual to explain to the customer how to use and maintain the unit.
Relocation
• Only a qualified installer(*1) or qualified service person(*1) is allowed to relocate the air conditioner. It is dangerous for the
air conditioner to be relocated by an unqualified individual since a fire, electric shocks, injury, water leakage, noise and/or
vibration may result.
• When carrying out the pump-down work shut down the compressor before disconnecting the refrigerant pipe. Disconnecting
the refrigerant pipe with the service valve left open and the compressor still operating will cause air, etc. to be sucked in,
raising the pressure inside the refrigeration cycle to an abnormally high level, and possibly resulting in rupture, injury or other
trouble.
(*1) Refer to the “Definition of Qualified Installer or Qualified Service Person.”
– 6 –
6-EN
Installation Manual
Concealed Duct High Static Pressure
CAUTION
New Refrigerant Air Conditioner Installation
• THIS AIR CONDITIONER ADOPTS THE NEW HFC REFRIGERANT (R410A) WHICH DOES NOT DESTROY OZONE
LAYER.
• The characteristics of R410A refrigerant are; easy to absorb water, oxidizing membrane or oil, and its pressure is approx.
1.6 times higher than that of refrigerant R22. Accompanied with the new refrigerant, refrigerating oil has also been changed.
Therefore, during installation work, be sure that water, dust, former refrigerant, or refrigerating oil does not enter the
refrigerating cycle.
• To prevent charging an incorrect refrigerant and refrigerating oil, the sizes of connecting sections of charging port of the
main unit and installation tools are changed from those for the conventional refrigerant.
• Accordingly the exclusive tools are required for the new refrigerant (R410A).
• For connecting pipes, use new and clean piping designed for R410A, and please care so that water or dust does not enter.
To Disconnect the Appliance from Main Power Supply.
• This appliance must be connected to the main power supply by means of a switch with a contact separation of at least 3 mm.
• The installation fuse must be used for the power supply line of this conditioner.
7-EN
– 7 –
Installation Manual
Concealed Duct High Static Pressure
2 ACCESSORY PARTS
Part name
Q’ty
Shape
Usage
(Be sure to hand over to customers)
(For other languages that do not appear in this Installation Manual,
please refer to the enclosed CD-R.)
Installation Manual
2
This manual
Owner’s Manual
1
(Be sure to hand over to customers)
1
1
For heat insulation of Gas pipe connecting section
For heat insulation of Liquid pipe connecting section
Heat insulator
Joint (Ø22.2 – Ø28.6 mm)
1
For connecting the gas side pipe
EN
– 8 –
8-EN
Installation Manual
Concealed Duct High Static Pressure
3 SELECTION OF INSTALLATION PLACE
Upon approval of the customer, install the air conditioner in a place that satisfies the following
conditions.
• Place where the unit can be installed horizontally.
• Place where a sufficient servicing space can be ensured for safety maintenance and check.
• Place where drained water will not cause any problem.
Avoid installing in the following places.
• Place exposed to air with high salt content (seaside area), or place exposed to large quantities of sulfide gas (hot spring).
(Should the unit be used in these places, special protective measures are needed.)
• A restaurant kitchen where a lot of oil is used or place near machines in a factory (Oil adhering to the heat exchanger and
resin part (fan) in the indoor unit may reduce the performance, generate mist or dew drop, or deform or damage resin parts.)
• Place where organic solvent is used nearby.
• Place close to a machine generating high frequency.
• Place where the discharged air blows directly into the window of the neighbour house. (Outdoor unit)
• Place where noise of the outdoor unit is easily transmitted.
(When install the outdoor unit on the boundary with the neighbour, pay due attention to the level of noise.)
• Place with poor ventilation. (Before air duct installation, check whether value of air volume, static pressure and duct
resistance are correct.)
• Do not use the air conditioner for special purposes such as preserving food, precision instruments, or art objects, or where
breeding animals or growing plants are kept. (This may degrade the quality of preserved materials.)
• Place where any of high-frequency appliances (including inverter devices, private power generators, medical equipment, and
communication equipment) and inverter-type fluorescent light is installed.
(A malfunction of the air conditioner, abnormal control, or problems due to noise to such appliances/equipment may occur.)
• When the wireless remote controller is used in a room equipped with an inverter-type fluorescent light or at a place exposed
to direct sunlight, signals from the remote controller may not be received correctly.
• Place where organic solvent is used.
• Place where special spray is used frequently.
Installation under high-humidity atmosphere
In some cases including the rainy season, especially inside of the ceiling may become high-humidity atmosphere (dew-point
temperature: 23°C or higher).
1. Installation to inside of the ceiling with tiles on the roof
2. Installation to inside of the ceiling with slated roof
3. Installation to a place where inside of the ceiling is used for pathway to intake the fresh air
• In the above cases, additionally attach the heat insulator to all positions of the air conditioner, which come to contact with the
high-humidity atmosphere. In this case, arrange the side plate (Check port) so that it is easily removed.
• Apply also a sufficient heat insulation to the duct and connecting part of the duct.
[Reference]
Condensation test conditions
27°C dry bulb temperature
24°C wet bulb temperature
Indoor side:
Air volume:
Low air volume, operation time 4 hours
9-EN
– 9 –
Installation Manual
(Unit: mm)
Concealed Duct High Static Pressure
Installation space
Reserve space required for maintenance the indoor unit and service work.
200 or more Servicing space
Concealed duct high
static pressure
1000 or more
Check port with carrying
in port 600x600
Air flow direction
<Installation example>
Concealed
duct high static
pressure
Filter chamber
Air inlet chamber
Air outlet chamber
EN
Duct hose
Duct hose
Duct hose
Air flow direction
REQUIREMENT
1. Attach the optional accessories (drain-up kit etc.) on the unit before installing the unit. Also, set the check port with carrying
in port to the side surface of the unit except air inlet panel.
2. Prepare the check port with carrying in port hole with the size of 600x600mm.
Filter cleaning sign term setting
The lighting term setup of the filter sign (Notification of filter cleaning) of the remote controller can be changed according to the
condition of installation.
For setup method, refer to “Filter sign setting” and “To secure better effect of heating” in the Applicable controls of this Manual.
– 10 –
10-EN
Installation Manual
Concealed Duct High Static Pressure
4 INSTALLATION
WARNING
• Install the air conditioner certainly to sufficiently withstand the weight.
• If the strength is insufficient, the unit may fall down resulting in human injury.
• Perform a specified installation work to guard against strong wind or earthquake.
• An incomplete installation can cause accidents by the units falling and dropping.
REQUIREMENT
Strictly comply with the following rules to prevent damage of the indoor units and human injury.
• Do not put a heavy article on the indoor unit. (Even units are packaged)
• Carry in the indoor unit as it is packaged if possible. If carrying in the indoor unit unpacked by necessity, be sure to use
buffering cloth, etc. to not damage the unit.
• To move the indoor unit, hold the hooking metals (4 positions) only.
Do not apply force to the other parts (refrigerant pipe, drain pan, foamed parts, or resin parts, etc.).
• Hanging bolt pitch of air inlet chamber side is different (centre position), make sure not to make mistake to install the setting
direction.
• Carry the package by two or more persons, and do not bundle it with plastic band at positions other than specified.
External Dimensions
(Unit: mm)
4-M10 hanging bolt
(Local procure)
1288 (Hanging bolt pitch)
1328
Electrical control box
Refrigerant pipe connecting port
(Gas side Ø22.2 Brazed)
Refrigerant pipe connecting port
(Liquid side Ø12.7 Flared)
1250
22
Drain pipe
connecting port
624
698
46
65
11-EN
– 11 –
Installation Manual
Concealed Duct High Static Pressure
Installation of hanging bolt
Installation of indoor unit
• Consider the piping/wiring after the unit is hung when
determining the location of the indoor unit installation and
orientation.
Treatment of ceiling
The ceiling differs according to structure of building.
For details, consult your constructor or interior finish
contractor.
• After the location of the indoor unit installation has been
determined, install hanging bolts.
• For the dimensions of the hanging bolt pitches, refer to the
external view.
In the process after the ceiling board has been removed, it is
important to reinforce ceiling foundation (frame) and to keep
horizontal level of installed ceiling correctly in order to
prevent vibration of ceiling board.
• When a ceiling already exists, lay the drain pipe,
refrigerant pipe, system interconnection wires, and remote
controller wires to their connection locations before
hanging the indoor unit.
• Attach the nuts and the M10 flat washers to the hanging
bolt.
Procure hanging bolts washer and nuts for installing the
indoor unit (these are not supplied).
• Put washers at up and down of the hanging bracket of the
indoor unit to hang down the indoor unit.
• Using a level vial, check that four sides are horizontal.
(Horizontal degree: Within 5mm)
Hanging bolt
Nut
M10 or W3/8
M10 or W3/8
M10
4 pieces
12 pieces
8 pieces
Washer
Hanging bolt
(W3/8 or M10)
M10 flat washer
Installation of hanging bolt
Nut
(W3/8 or M10)
Use M10 hanging bolts (4 pcs, to be local procure).
Matching to the existing structure, set pitch according to size
in the unit external view as shown below.
M10 flat washer
Nut
(W3/8 or M10)
EN
New concrete slab
Install the bolts with insert brackets or anchor bolts.
• Check that four sides are horizontal using a level vial.
(Horizontal degree: Within 5mm)
Rubber
Anchor bolt
REQUIREMENT
(Slide type
bracket)
(Blade type
bracket)
(Pipe hanging
anchor bolt)
• Hang the unit in a horizontal position.
When unit is hanged to slant, it may cause overflow of
drainage.
Steel flame structure
• Install the unit within the dimension according to the figure
below.
Use existing angles or install new support angles.
Hanging bolt
• Using level vial or vinyl hose to confirm whether the unit
is hang horizontally.
Side view
Front view
Support angle
Hanging bolt
Water pouring
Vinyl hose
Existing concrete slab
Use a hole-in anchors, hole-in plugs, or a hole-in bolts.
Set the air inlet and air
outlet sides are within
5mm with each other.
Set the drain pipe
connecting port side within
5mm lower than opposite
side.
– 12 –
12-EN
Installation Manual
(Unit: mm)
Concealed Duct High Static Pressure
Diagrams for making connecting flanges
The connecting flange (Incl. the fixing screw) is not supplied to the indoor unit. When the connecting flange is necessary,
produce them in locally.
Drawing figure is as follows. (Material: Galvanized steel plate, thickness of 1.6 mm)
<Air outlet port flange>
1130
65
250
250
250
250
65
1080
25
25
10-Ø8 hole
<Air inlet port connecting flange>
1130
65
250
250
250
250
65
1080
25
25
10-Ø8 hole
13-EN
– 13 –
Installation Manual
Concealed Duct High Static Pressure
Duct design
1. In order to prevent short circuits, design the duct installation, so that the intake and discharge openings are not
adjacent to each other.
2. The indoor unit does not have a built-in air filter. Make sure to set up the filter chamber etc. and install the air filter (Locally
procured). If no air filter is installed, the heat exchanger will be blocked by dust, which may cause the malfunction of air
conditioner or the water leakage.
<Duct installation example (First floor)>
High efficiency filter
Air outlet chamber
inserting port
(with heat insulation)
Pre filter
inserting port
Air outlet port
connecting flange
Flexible duct hanging band
Air inlet port
connecting flange
Indoor unit
Duct hose (with heat insulation)
Electrical control
box
Filter Air inlet
chamber chamber
EN
Duct hose
Air outlet port
Air outlet port
Ceiling
Check port or carrying
in port (600x600)
Check port cap
from ground floor
to ground floor
NOTE
All duct connection between units except outdoor unit must be procured and enforced locally.
– 14 –
14-EN
Installation Manual
Concealed Duct High Static Pressure
5 FAN CHARACTERISTICS
Current value as a criterion, adjust the air volume value to become within the range of the chart below.
<RAV-SM2242 Type>
Standard air volume: 3600m³/h
8
7.5
7
6.5
High static pressure tap (50Hz)
6
5.5
5
Medium static pressure tap (50Hz)
Low static pressure tap (50Hz)
4.5
4
300
250
200
150
100
High static pressure tap (50Hz)
Medium static pressure tap (50Hz)
Low static pressure tap (50Hz)
50
5
2800
3000
3400
3800
4200 4400
4000 4320
2880
Lower limit of air volume
3200
3600
Air volume (m³/h)
Upper limit of air volume
15-EN
– 15 –
Installation Manual
Concealed Duct High Static Pressure
<RAV-SM2802 Type>
Standard air volume: 4200m³/h
8.5
8
7.5
7
High static pressure tap (50Hz)
6.5
6
Medium static pressure tap (50Hz)
Low static pressure tap (50Hz)
5.5
5
4.5
4
350
300
250
200
150
100
EN
High static pressure tap (50Hz)
Medium static pressure tap (50Hz)
50
5
Low static pressure tap (50Hz)
3200 3400
3800
4200
4600
5000 5200
4800 5040
3360
3600
4000
4400
Lower limit of air volume
Air volume (m³/h)
Upper limit of air volume
REQUIREMENT
Add a air volume damper to the air supply duct, and adjust the air volume in the range from 80% to 120% of the standard air
volume.
– 16 –
16-EN
Installation Manual
Concealed Duct High Static Pressure
Wire connection change of fan motor
This duct is composed of 3 fan motors.
To change external static pressure by duct resistance, connect the 3 connectors of the orange lead wires that are connected to
the underside of the fan tap changing terminal block to the same number (F1, F2 or F3) terminal.
The wires of the fan motor has been connected to (F2) [External static pressure 137Pa (14mmAq)] as factory default.
YEL: Yellow
BLU: Blue
ORG: Orange
Low static pressure (F1)
FM
FM
Fan motor
FM
Fan motor
Fan motor
F
1
F
2
F
3
F
4
F
1
F
2
F
3
F
4
F
F
F
1
1
1
F
F
F
2
2
2
F
F
F
3
3
3
F4
FAN2
FAN1
FAN3
Standard (Middle) static pressure (F2)
Fan tap changing
terminal block
Electrical control box
FM
FM
FM
Control
P.C. board
Fan motor
Fan motor
Fan motor
4P terminal
block
F
1
F
2
F
3
F
4
F
1
F
2
F3
F4
F4
3P terminal
block
FAN2
FAN1
FAN3
2P terminal
block
High static pressure (F3)
FM
FM
FM
Fan motor
Fan motor
Fan motor
F
1
F
2
F
3
F
4
F
1
F
2
F3
F4
F4
FAN2
FAN1
FAN3
External static pressure
Pa (mmAq)
Terminal block No.
Fan motor wiring
Remarks
Yellow
Low static pressure
F1
F2
F3
69 (7)
Blue
Middle static pressure
137 (14)
196 (20)
Factory default
Orange
High static pressure
* Do not use F4.
NOTE
When the external static pressure is changed, write down the static pressure once change in the wiring diagram of the indoor
unit is made.
17-EN
– 17 –
Installation Manual
Concealed Duct High Static Pressure
6 DRAIN PIPING WORK
CAUTION
Following the Installation Manual, perform the drain piping work that water is properly drained, and apply a heat
insulation not to cause a dew condensation.
Inappropriate piping work may cause the water leakage in the room and wet of furniture.
REQUIREMENT
• The drain piping flows the natural drainage. Make sure to set the drain piping from the unit with descending slope of 1/50 to
1/100 and do not make up-down or trap in the midway.
• Set the horizontal pulling of the drain pipe to 20m or less. When drain piping is too long, attach the support bracket at
intervals of 1.5m to 2m to avoid the pipe becomes undulant as shown in figure below.
<Example for installation of the main piping (Incl. piping support)>
As long as possible
1.5 to 2 m
Up-down bend
Trap
Descending slop of
1/50 to 1/100
VP-30
Descending slop of
1/50 to 1/100
• Be sure to connect the drain pipe to the air conditioner with adhesive to avoid water leakage from the joint portion.
• Condensation may occur on the drain pipes including collective pipes. All drain pipes must be wrapped with heat insulator
to prevent dew condensation. Especially a part where drain pipe is connected to the indoor unit must be firmly insulated with
the provided heat insulator.
EN
– 18 –
18-EN
Installation Manual
Concealed Duct High Static Pressure
Pipe material, size and insulator
The following materials for piping work and insulating process are procured locally.
Hard vinyl chloride pipe socket for VP25
Pipe material
Hard vinyl chloride pipe VP25 (Nominal outer diameter Ø32mm)
Insulator
Foamed polyethylene foam, thickness: 10mm or more
Connecting drain pipe
REQUIREMENT
• Using adhesive agent for vinyl chloride, connect the hard vinyl chloride pipes certainly so that water does not leak.
• It takes some time to dry and indurate the adhesive agent. (Refer to the manual of adhesive agent.) Do not apply any extra
force on the connecting section until the adhesive agent dried.
Drain up
• When install the drain up kit of optional accessory, read the Installation Manual supplied to a drain up kit.
19-EN
– 19 –
Installation Manual
Concealed Duct High Static Pressure
Check the draining
Check if the water can flow out properly during the test run. Also, check if no water leakage from the piping connection port.
REQUIREMENT
• Do drain test even if installation of heating season.
• Pour water into the drain pan port of the air inlet port gently using the kettle or hose when duct is not connected to the drain
pipe. When duct is connected to the drain pipe, remove the Access plate and perform it.
Access plate
Pour into the drain pan with a hose or
other materials.
EN
– 20 –
20-EN
Installation Manual
Concealed Duct High Static Pressure
Heat insulating process
• After drain check, covering the heat insulator for drain connecting section, wrap the drain pipe with heat insulator (Locally
procured) without clearance from the end of the drain pipe connecting port of the indoor unit.
Heat insulation (Locally procured)
Thickness 10mm or more
Drain pipe connecting port
Indoor unit
21-EN
– 21 –
Installation Manual
Concealed Duct High Static Pressure
7 REFRIGERANT PIPING AND EVACUATING
Flaring
Refrigerant Piping
• Cut the pipe with a pipe cutter.
Remove burrs completely.
1. If the outdoor units are to be mounted on a wall,
make sure that the supporting platform is sufficiently
strong. The platform should be designed and
manufactured to maintain its strength over a long
period of time, and sufficient consideration should
be given to ensuring that the outdoor unit will not fall.
2. Use general copper pipes with a wall thickness of 0.8
mm for Ø12.7 mm, and with a wall thickness of 1.0
mm for Ø28.6 mm (half hard).
Remaining burrs may cause gas leakage.
• Insert a flare nut into the pipe, and flare the pipe.
As the flaring sizes of R410A differ from those of
refrigerant R22, the flare tools newly manufactured for
R410A are recommended.
B
However, the conventional tools can
be used by adjusting projection
margin of the copper pipe.
Do not use any copper pipes with a wall thickness
less than these thicknesses.
3. Flare nut and flare works are also different from those of
the conventional refrigerant.
M Projection margin in flaring: B (Unit: mm)
Rigid (Clutch type)
Take out the flare nut attached to the main unit of the air
conditioner, and use it.
Conventional tool
used
R410A tool used
Outer dia. of
copper pipe
REQUIREMENT
R410A
R410A
When the refrigerant pipe is long, provide support brackets at
intervals of 2.5 to 3m to clamp the refrigerant pipe. Otherwise,
abnormal sound may be generated.
12.7
0 to 0.5
1.5 to 2.0
EN
M Flaring dia. meter size: A (Unit: mm)
+0
-0.02" (–0.4)
A
CAUTION
Outer dia. of copper pipe
12.7
R410A
IMPORTANT 4 POINTS FOR PIPING WORK
1. Remove dust and moisture from the inside of the
connecting pipes.
16.6
* In case of flaring for R410A with the
A
conventional flare tool, pull it out approx.
0.5 mm more than that for R22 to adjust to the
specified flare size.
The copper pipe gauge is useful for adjusting
projection margin size.
2. Tight connection (between pipes and unit)
3. Evacuate the air in the connecting pipes using
VACUUM PUMP.
4. Check the gas leakage. (Connected points)
Pipe size
Gas side
28.6 mm
12.7 mm
Pipe size
Liquid side
Liquid side refrigerant pipe
connection
Permissible Piping Length and Height
Difference
They vary according to the outdoor unit.
For details, refer to the Installation Manual attached to the
outdoor unit.
– 22 –
22-EN
Installation Manual
Concealed Duct High Static Pressure
• Remove the cup on the gas side piping by using a brazing
machine.
Tightening connection
CAUTION
CAUTION
Do not apply excessive torque. Otherwise, the nut
may crack depending on the conditions.
Do not burn the pipe heat insulator.
Remove the cap.
Attached joint part
(Unit: N•m)
Outer dia. of copper pipe
Tightening torque
12.7 mm (dia.)
50 to 62 (5.0 to 6.2 kgf•m)
M Tightening torque of flare pipe connections
Pressure of R410A is higher than that of R22.
(Approx. 1.6 times) Therefore, using a torque wrench, tighten
the flare pipe connecting sections which connect the indoor
and outdoor units of the specified tightening torque.
Incorrect connections may cause not only a gas leak, but also
a trouble of the refrigeration cycle.
Connection pipe
Locally procured
Ø28.6 mm
Align the centres of the connecting pipes and tighten the flare
nut as far as possible with your fingers. Then tighten the nut
with a spanner and torque wrench as shown in the figure.
• Braze the attached joint part to the gas side piping and
braze the connection piping to the joint part.
brazing
Half union
Flare nut
Braze all around
brazing
Internally
threaded side
Externally
threaded side
Use a wrench to secure.
Use a torque wrench to tighten.
• Turn back the pipe heat insulator and tie up with a banding
band.
REQUIREMENT
Tightening with an excessive torque may crack the nut
depending on installation conditions.
Tighten the nut within the specified tightening torque.
Tie up with a banding
band.
Piping with outdoor unit
Gas side refrigerant pipe
connection
• For details of installation, refer to the Installation Manual of
the outdoor unit.
• Turn up the pipe heat insulator to the unit side.
• Wrap the pipe with wet cloth.
Evacuation
Turn up pipe heat
insulator
Using a vacuum pump, perform vacuuming from the charge
port of valve of the outdoor unit.
For details, follow to the Installation Manual attached to the
outdoor unit.
• Never use the refrigerant sealed in the outdoor unit for
evacuation.
Wet cloth
Remove the all
brazed part.
REQUIREMENT
For the tools such as charge hose, etc., use those
manufactured exclusively for R410A.
23-EN
– 23 –
Installation Manual
Concealed Duct High Static Pressure
Refrigerant amount to be added
Heat insulation process
For addition of the refrigerant, add refrigerant “R410A”
referring to the attached Installation Manual of outdoor unit.
Be sure to use a scale to charge the refrigerant of specified
amount.
Apply heat insulation for the pipes separately at liquid side
and gas side.
For the heat insulation to the pipes at gas side, be sure to use
the material with heat-resisting temperature 120°C or higher.
Using the attached heat insulation material, apply the heat
insulation to the pipe connecting section of the indoor unit
securely without gap.
REQUIREMENT
• Charging an excessive or too little amount of refrigerant
causes a trouble of the compressor.
REQUIREMENT
Be sure to charge the refrigerant of specified amount.
• A personnel who charged the refrigerant should write
down the pipe length and the added refrigerant amount in
the nameplate attached to the service panel of the
outdoor unit. It is necessary to fix the compressor and
refrigeration cycle malfunction.
• Apply the heat insulation to the pipe connecting section of
the indoor unit securely up to the root without exposure of
the pipe. (The pipe exposed to the outside causes water
leak.)
• Wrap heat insulator with its slits facing up (ceiling side).
Indoor unit
Union
Open the valve fully
Open the valve of the outdoor unit fully. A 4mm-hexagonal
wrench is required for opening the valve.
For details, refer to the Installation Manual attached to the
outdoor unit.
Gas leak check
EN
Heat insulator of
the pipe
Check with a leak detector or soap water whether gas leaks
or not, from the pipe connecting section or cap of the valve.
Heat insulation
(Accessory)
Flare nut
REQUIREMENT
Use a leak detector manufactured exclusively for HFC
refrigerant (R410A, R134a, etc.).
– 24 –
24-EN
Installation Manual
Concealed Duct High Static Pressure
8 ELECTRICAL CONNECTION
WARNING
Remote controller wiring
2-core non polarity wire is used for the remote controller
wiring.
1. Using the specified wires, ensure to connect
the wires, and fix wires securely so that the
external tension to the wires do not affect the
connecting part of the terminals.
Wiring
1. Figure below shows the wiring connections indoor
power line and between the indoor and outdoor units
and between the indoor units and remote controller.
The wires indicated by the dash lines are provided at
the installation place.
Incomplete connection or fixation may cause a fire,
etc.
2. Be sure to connect earth wire. (grounding
work)
Incomplete grounding cause an electric shock.
Do not connect ground wires to gas pipes, water
pipes, lightning rods or ground wires for telephone
wires.
2. Insulate the unsheathed redundant cords (conductors)
with electrical insulation tape.
Process them so that they do not touch any electrical or
metal parts.
3. Appliance shall be installed in accordance with
national wiring regulations.
Capacity shortage of power circuit or incomplete
installation may cause an electric shock or a fire.
Wiring diagram
Outdoor Input power
380-415V 3N~, 50 Hz
CAUTION
L
L
L
1
2
3
Outdoor
unit
• If incorrect/incomplete wiring is carried out, it will cause
an electrical fire or smoke.
N
• Be sure to install an earth leakage breaker that is not
tripped by shock waves.
If an earth leakage breaker is not installed, an electric
shock may be caused.
• Be sure to use the cord clamps attached to the product.
• Do not damage or scratch the conductive core and inner
insulator of power and inter-connecting wires when
peeling them.
• Use the power cord and Inter-connecting wire of
specified thickness, type, and protective devices
required.
1
1
2
3
Circuit breaker
(Leakage breaker)
Indoor Fan Input power
220-240V~, 50 Hz
2
3
L
Indoor
unit
N
A
B
Circuit breaker
(Leakage breaker)
REQUIREMENT
Wired remote
controller
• For power supply wiring, strictly conform to the Local
Regulation in each country.
• Power supply for indoor unit must be exclusive and
separated from the one for outdoor unit.
Power and Wiring
Specification
• For wiring of power supply of the outdoor units, follow the
Installation Manual of each outdoor unit.
• Never connect 220–240V power to the terminal blocks
A
B
(
,
(Otherwise, the system will fail.)
, etc.) for control wiring.
Indoor fan Power supply
220-240V~, 50 Hz
• Perform the electric wiring so that it does not come to
contact with the high-temperature part of the pipe.
The coating may melt resulting in an accident.
• After connecting wires to the terminal blocks, provide a
trap and fix wires with the cord clamp.
Maximum running
current
15A
25A
Fuse rating
3 x 2.5mm2 or more
(H07 RN-F or 60245 IEC 66)
Indoor fan power supply
wire*
• Run the refrigerant piping line and control wiring line in
the same line.
4 x 1.5mm2 or more
(H07 RN-F or 60245 IEC 66)
System interconnecting
wires*
• Do not turn on the power of the indoor unit until
vacuuming of the refrigerant pipes completes.
*Number of wire x wire size
25-EN
– 25 –
Installation Manual
Concealed Duct High Static Pressure
Wire connection
REQUIREMENT
• Be sure to connect the wires matching the terminal numbers. Incorrect connection causes a trouble.
• Be sure to pass the wires through the bushing of wire connection holes of the indoor unit.
• Keep a margin (Approx. 100mm) on a wire to hang down the electrical control box at servicing, etc.
• The low-voltage circuit is provided for the remote controller. (Do not connect the high-voltage circuit)
1. Remove the cover of the electrical control box by taking off the mounting screws (2 positions)
2. Tighten the screws of the terminal block, and fix the wires with cord attached to the electrical control box.
(Do not apply tension to the connecting section of the terminal block.)
3. Mount the cover of the electrical control box without pinching wires.
<Terminal block of electrical control box>
Electrical
control box
cover
System
interconnecting
Terminal block
Wired remote controller
connecting Terminal
block
Indoor fan power
supply Terminal
block
Fixing screw
EN
Bushing
Wired remote
controller wire
Indoor fan power supply
wire
Cord clamp
System interconnecting
wire
– 26 –
26-EN
Installation Manual
Concealed Duct High Static Pressure
Group control
(Unit: mm)
Wired remote
controller
S (N)
R (L)
A
B
A
B
Indoor Unit
Indoor Unit
Outdoor Unit
Outdoor Unit
Indoor fan power supply wire
1
2
3
System interconnecting wire
Remote Controller Wiring
• Strip off approx. 9mm the wire to be connected.
• Non polarity, 2 core wire is used for wiring of the remote
controller. (0.5mm² to 2.0mm² wires)
Wiring diagram
Terminal block for
remote controller
wiring of indoor unit
Terminal block
Remote
controller
A
B
A
B
unit
Remote controller wire
(Locally procured)
27-EN
– 27 –
Installation Manual
Concealed Duct High Static Pressure
9 APPLICABLE CONTROLS
Procedure 1
Push button and TEMP.
at least 4 seconds.
REQUIREMENT
button simultaneously for
• When you use this air conditioner for the first time, it takes
approx. 5 minutes until the remote controller becomes
available after power-on. This is normal.
<When power is turned on for the first time after
installation>
After a while, the display flashes as shown in the figure.
Confirm that the CODE No. is [01].
• If the CODE No. is not [01], push
button to erase the
display content, and repeat the procedure from the
beginning.
(No operation of the remote controller is accepted for a
It takes approx. 5 minutes until the remote controller
becomes available.
while after
button is pushed.)
Approx. 5 minutes
Remote
controller is
available
“SETTING”
goes out
“SETTING”
flashes
Power on
<When power is turned on for the second (or
later) time>
(* Display content varies with
the indoor unit model.)
It takes approx. 1 minute until the remote controller
becomes available.
Procedure 2
Each time you push
button, indoor unit numbers in
the control group change cyclically. Select the indoor unit you
want to change settings for.
Approx. 1 minutes
Remote
controller is
available
“SETTING”
goes out
The fan of the selected unit runs. You can confirm the indoor
unit for which you want to change settings.
“SETTING”
flashes
Power on
EN
• Normal settings were made when the indoor unit was
shipped from factory.
Change the indoor unit settings as required.
• Use the wired remote controller to change the settings.
* The settings cannot be changed using the wireless
remote controller, sub remote controller, or remote-
controller-less system (for central remote controller
only). Therefore, install the wired remote controller to
change the settings.
Procedure 3
Using TEMP.
/
buttons, specify CODE No. [
buttons, select SET DATA
].
Procedure 4
Using TIME
/
[
].
Procedure 5
Push
lit, the setup is completed.
button. When the display changes from flashing to
Changing of setting
applicable control
• To change settings of another indoor unit, repeat from
Procedure 2.
• To change other settings of the selected indoor unit, repeat
Basic procedure for changing settings
Change the settings while the air conditioner is not working.
(Be sure to stop the air conditioner before making settings.)
from Procedure 3.
Use
To make settings after
button to clear the settings.
button was pushed, repeat from
Procedure 2.
1
3
4
6
1 5
2
– 28 –
28-EN
Installation Manual
Concealed Duct High Static Pressure
Procedure 6
When settings have been completed, push
Power saving mode
button to
determine the settings.
When
1. Push
button for at least four seconds when
button is pushed, “SETTING” flashes and then the
display content disappears and the air conditioner enters the
normal stop mode.
the air conditioner is not working.
flashes.
Indicates CODE No. “C2.”
2. Select an indoor unit to be set by pushing
side of the button).
(While “SETTING” is flashing, no operation of the remote
controller is accepted.)
(left
Each time you push the button, unit numbers change as
follows:
UNIT No.
1-1
UNIT No.
1-2
UNIT No.
1-3
UNIT No.
1-4
Filter sign setting
The fan of the selected unit runs.
3. Adjust the power save setting by pushing TIME
buttons.
According to the installation condition, the filter sign term
(Notification of filter cleaning) can be changed.
Follow to the basic operation procedure
Each push of the button changes the power level by 1%
within the range from 100% to 50%.
* The factory default is 75%.
(1 ꢀ 2 ꢀ 3 ꢀ 4 ꢀ 5 ꢀ 6).
• For the CODE No. in Procedure 3, specify [01].
• For the [SET DATA] in Procedure 4, select the SET DATA
of filter sign term from the following table.
SET DATA
0000
Filter sign term
None
0001
150H
2500H
(Factory default)
0002
Setting of power level in
power saving mode
0003
0004
5000H
4. Determine the setting by pushing
button.
10000H
5. Push button to complete the setting.
To secure better effect of
heating
When it is difficult to obtain satisfactory heating due to
installation place of the indoor unit or structure of the room,
the detection temperature of heating can be raised. Also use
a circulator, etc. to circulate heat air near the ceiling.
Follow to the basic operation procedure
(1 ꢀ 2 ꢀ 3 ꢀ 4 ꢀ 5 ꢀ 6).
• For the CODE No. in Procedure 3, specify [06].
• For the set data in Procedure 4, select the SET DATA of
shift value of detection temperature to be set up from the
table below.
SET DATA
0000
Detection temperature shift value
No shift
+1°C
0001
+2°C
(Factory default)
0002
0003
0004
0005
0006
+3°C
+4°C
+5°C
+6°C
29-EN
– 29 –
Installation Manual
Concealed Duct High Static Pressure
Remote controller switch
monitoring function
Outdoor unit data
Data name
CODE No.
60
Outdoor unit heat exchanger (coil)
temperature (TE)
This function is available to call the service monitor mode
from the remote controller during a test run to acquire
temperatures of sensors of the remote controller, indoor unit,
and outdoor unit.
61
62
63
64
65
6A
Outside air temperature (TO)
Compressor discharge temperature (TD)
Compressor suction temperature (TS)
—
Heatsink temperature (THS)
Operating current (x1/10)
Compressor cumulative operating hours
(x100h)
F1
2
4
1
3
1. Push
and
buttons simultaneously for at least
4 seconds to call the service monitor mode.
The service monitor indicator lights up and the
header indoor unit number is displayed first. CODE
EN
No.
is also displayed.
buttons, select the number of
2. Pushing TEMP.
sensor, etc. (CODE No.) to be monitored. (See the
following table.)
3. Pushing
(left side of the button), select an indoor
unit to be monitored. The sensor temperatures of indoor
units and their outdoor unit in the control group are
displayed.
4. Push
button to return to the normal display.
Indoor unit data
CODE No.
Data name
01
02
Room temperature (remote controller)
Indoor unit intake air temperature (TA)
Indoor unit heat exchanger (coil)
temperature (TCJ)
03
04
F3
Indoor unit heat exchanger (coil)
temperature (TC)
Indoor unit fan cumulative operating hours
(x1 h)
– 30 –
30-EN
Installation Manual
Concealed Duct High Static Pressure
Group control
Group control for system of multiple units
One remote controller can control up to 8 indoor units as a group.
M Group control in single system
Outdoor unit
Outdoor unit
Outdoor unit
Indoor unit
Outdoor unit
Indoor unit
Outdoor unit
Indoor unit
Indoor unit
Indoor unit
(Max. 8 units)
Remote controller
Finish of address setup by power-ON
• For wiring procedure and wiring method of the individual line (Identical refrigerant line) system, refer to “ELECTRICAL
CONNECTION”.
• Wiring between lines is performed in the following procedure.
Connect the terminal block (A/B) of the indoor unit connected with a remote controller to the terminal blocks (A/B) of the indoor
units of other indoor units by wiring the inter-unit wire of the remote controller.
• When the power supply has been turned on, the automatic address setup starts and which indicates that address is being
set up flashes on the display part. During setup of automatic address, the remote controller operation is not accepted.
Required time up to the finish of automatic addressing is approx. 5 minutes.
NOTE
In some cases, it is necessary to change the address manually after setup of the automatic address according to the system
configuration of the group control.
31-EN
– 31 –
Installation Manual
Concealed Duct High Static Pressure
Procedure example 1
3. Push
button.
In this time, the setup finishes when the display changes
from flashing to lighting.
Manual address setup procedure
While the operation stops, change the setup.
(Be sure to stop the operation of the unit.)
Indoor unit No. before setup change is displayed.
7
3
4
5
-2,
-2,
-2
3
4
-1,
-1,
5 -1,
6
7
3
4
5
-3,
-3,
-3,
Procedure 4
1. Using TEMP.
/
buttons, specify CODE No.
1
2,6
[13].
(CODE No. [13]: Indoor address)
Procedure 1
Push simultaneously
2. Using TIME
address from [
/
buttons, change the indoor
].
+
more. After a while, the display part flashes as shown below.
+
buttons for 4 seconds or
3
] to [
2
3. Push
button.
Check the displayed CODE No. is [10].
In this time, the setup finishes when the display changes
from flashing to lighting.
• When the CODE No. is other than [10], push
erase the display and repeat procedure from the first step.
(After pushing button, operation of the remote
button to
Indoor unit No. before setup change is displayed.
EN
controller is not accepted for approx. 1 minute.)
(For a group control, No. of the firstly displayed indoor unit
becomes the header unit.)
(* Display changes according to
the model No. of indoor unit.)
Procedure 5
1. Using TEMP.
[14].
(CODE No. [14]: Group address)
2. Using TIME buttons, change the SET DATA
from [0001] to [0002].
(SET DATA [Header unit: 0001] [Follower unit: 0002])
Procedure 2
Every pushing
button, the indoor UNIT No. in the
/
buttons, specify CODE No.
group control is displayed in order. Select the indoor unit of
which setup is changed.
In this time, the position of the indoor unit of which setup is
changed can be confirmed because fan of the selected
indoor unit operate.
/
3. Push
button.
Procedure 3
1. Using TEMP.
[12].
In this time, the setup finishes when the display changes
from flashing to lighting.
/
buttons, specify CODE No.
(CODE No. [12]: Line address)
2. Using TIME buttons, change the line address
from [ ] to [
Indoor UNIT No. before setup change is displayed.
/
3
2].
– 32 –
32-EN
Installation Manual
Concealed Duct High Static Pressure
Procedure 6
If there is other indoor unit to be changed, repeat procedure
To recognize the position of the
corresponding indoor unit though the
indoor UNIT No. is known
2 to 5 to change the setup.
When the above setup has finished, push
to select
the indoor UNIT No. before change of setup, specify CODE
Check the position during operation stop.
(Be sure to stop operation of the set.)
No. [12], [13], [14] in order with TEMP.
and then check the changed contents.
/
buttons,
Address change check Before change:
[3-3-1] ꢀ After change: [2-2-2]
Pushing
changed.
button clears the contents of which setup was
(In this case, procedure from 2 is repeated.)
Indoor UNIT No. before setup change is displayed.
1
2
1,3
Procedure 1
Push simultaneously
+
buttons for 4 seconds or
more.
After a while, the display part flashes and the display appears
as shown below.
In this time, the position can be checked because fan of the
indoor unit operate.
• For the group control, the indoor UNIT No. is displayed as
[ ] and fans of all the indoor units in the group control
operate.
Check the displayed CODE No. is [01].
• When the CODE No. is other than [01], push
button to
Procedure 7
After check of the changed contents, push
erase the display and repeat procedure from the first step.
(After pushing button, operation of the remote controller
is not accepted for approx. 1 minute.)
button. (Setup
is determined.) When pushing button, the display
disappears and the status becomes the usual stop status.
(When pushing button the operation from the remote
controller is not accepted for approx. 1 minute.)
* If the operation from the remote controller is not accepted
button, it
even 1 minute or more passed after pushing
is considered that the address setup is incorrect.
(* Display changes according to
the model No. of indoor unit.)
In this case, the automatic address must be again set up.
Therefore repeat procedure of the setup change from
the Procedure 1.
Procedure 2
In the group control, every pushing
button, the
indoor UNIT No. in the group control is displayed in order.
In this time, the position of the indoor unit can be confirmed
because only fan of the selected indoor unit operate.
(For a group control, No. of the firstly displayed indoor unit
becomes the header unit.)
Procedure 3
After confirmation, push
button to return the mode to the
usual mode.
When pushing
status becomes the usual stop status.
button, the display disappears and the
(When pushing button the operation from the remote
controller is not accepted for approx. 1 minute.)
33-EN
– 33 –
Installation Manual
Concealed Duct High Static Pressure
8°C Operation
Pre-heating operation can be set for cold regions where room
temperature drops to below zero.
Procedure 1
Push simultaneously
+
+
buttons for 4 seconds
or more when the air conditioner is not working.
After a while, the display part flashes as shown below. Check
the Displayed CODE No. is [10].
• When the CODE No. is other than [10], push
erase the display and repeat procedure from the first step.
(After pushing button, operation of the remote
button to
controller is not accepted for approx. 1 minute.)
(* Display changes according to
the model No. of indoor unit.)
Procedure 2
Every pushing
button, the indoor unit No. in the
group control is displayed in order. Select the indoor unit of
which setup is changed. In this time, the position of the indoor
unit of which setup is changed can be confirmed because fan
of the selected indoor unit operate.
EN
Procedure 3
Using TEMP.
/
buttons, specify CODE No. [d1].
Procedure 4
Using TIME
/
buttons, select SET DATA [0001].
SET DATA
0000
8°C Operation setting
None
(Factory default)
0001
8°C Operation setting
Procedure 5
Push
button.
In this time, the setup finishes when the display changes from
flashing to lighting.
Procedure 6
Push
button.(Setup is determined.)
When pushing
status
Becomes the usual stop status. (When pushing
button, the display disappears and the
button
the operation from the remote controller is not accepted for
approx. 1 minute.)
– 34 –
34-EN
Installation Manual
Concealed Duct High Static Pressure
10TEST RUN
Procedure 3
Before test run
Using
[Heat].
button, select the operation mode, [Cool] or
• Before turning on the power supply, carry out the following
procedure.
• Do not run the air conditioner in a mode other than [Cool]
or [Heat].
1) Using 500V-megger, check that resistance of 1M!
or more exists between the terminal block 1 to 3 and
the earth (grounding).
• The temperature controlling function does not work during
test run.
If resistance of less than 1M! is detected, do not run
the unit.
• The detection of error is performed as usual.
2) Check the valve of the outdoor unit being opened
fully.
• To protect the compressor at activation time, leave power-
ON for 12 hours or more before operating.
Procedure 4
After the test run, push
(Display part is same as procedure 1.)
Execute a test run
button to stop a test run.
Using the wired remote controller, operate the unit as usual.
For the procedure of the operation, refer to the attached
Owner’s Manual.
Procedure 5
Push
mode.
check button to cancel (release from) the test run
A forced test run can be executed in the following procedure
even if the operation stops by thermostat-OFF.
In order to prevent a serial operation, the forced test run is
released after 60 minutes have passed and returns to the
usual operation.
([TEST] disappears on the display and the status returns to a
normal.)
CAUTION
• Do not use the forced test run for cases other than the
test run because it applies an excessive load to the
devices.
2, 4
3
1,5
Procedure 1
Keep
button pushed for 4 seconds or more. [TEST] is
displayed on the display part and the selection of mode in the
test mode is permitted.
Procedure 2
Push
button.
35-EN
– 35 –
Installation Manual
Concealed Duct High Static Pressure
11MAINTENANCE
CAUTION
When connecting a return air duct to the unit, the cleaning method of the air filter differs according to the
construction of duct end. Ask a qualified installer or qualified service person.
<Daily maintenance>
Cleaning of air filter
1. If
is displayed on the remote controller, contact to qualified
installer or qualified service person.
2. Take out the air filter.
1,2
3
• Push the extrusion of the air filter to inside and pull out it to take
out the air filter.
3. Cleaning with water or vacuum cleaner
• If dirt is heavy, clean the air filter by tepid water with neutral
detergent or water.
• After cleaning with water, dry the air filter sufficiently in a shade
place.
4. Mount the air filter.
5. After cleaning, push
display disappears.
.
EN
CAUTION
• Do not start the air conditioner while leaving air filter removed.
• Push the filter reset button. (
indication will be turn off.)
PERIODIC MAINTENANCE
• For environmental conservation, it is strongly recommended that the indoor and outdoor units of the air conditioner in use be
cleaned and maintained regularly to ensure efficient operation of the air conditioner.
When the air conditioner is operated for a long time, periodic maintenance (once a year) is recommended.
Furthermore, regularly check the outdoor unit for rust and scratches, and remove them or apply rustproof treatment, if
necessary.
As a general rule, when an indoor unit is operated for 8 hours or more daily, clean the indoor unit and outdoor unit at least
once every 3 months. Ask a professional for this cleaning/maintenance work.
Such maintenance can extend the life of the product though it involves the owner’s expense.
Failure to clean the indoor and outdoor units regularly will result in poor performance, freezing, water leakage, and even
compressor failure.
• When a drain pump kit (sold separately) is installed.
If it is used in a place full of dust or oil mist, the pump will be clogged and proper drainage is disabled.
Clean the drain pump periodically. For how to clean the drain pump, contact the dealer.
– 36 –
36-EN
Installation Manual
Concealed Duct High Static Pressure
Maintenance List
Part
Unit
Check (visual/auditory)
Maintenance
• Dust/dirt clogging, scratches
• Wash the heat exchanger when it is
clogged.
Heat exchanger
Indoor/outdoor
• Sound
• Take appropriate measures when
abnormal sound is generated.
Fan motor
Filter
Indoor/outdoor
Indoor
• Dust/dirt, breakage
• Wash the filter with water when it is
contaminated.
• Replace it when it is damaged.
• Vibration, balance
• Dust/dirt, appearance
• Replace the fan when vibration or balance
is terrible.
• Brush or wash the fan when it is
contaminated.
Fan
Indoor
• Dust/dirt, scratches
• Fix or replace them when they are
deformed or damaged.
Air inlet/outlet grilles
Drain pan
Indoor/outdoor
Indoor
• Dust/dirt clogging, drain
contamination
• Clean the drain pan and check the
downward slope for smooth drainage.
Ornamental panel,
louvres
• Dust/dirt, scratches
• Wash them when they are contaminated or
apply repair coating.
Indoor
• Rust, peeling of insulator
• Peeling/lift of coat
• Apply repair coating.
Exterior
Outdoor
37-EN
– 37 –
Installation Manual
Concealed Duct High Static Pressure
12TROUBLESHOOTING
Procedure 2
Every pushing of
Confirmation and check
button used to set temperature, the
error log stored in memory is displayed in order.
The numbers in CODE No. indicate CODE No. [01] (latest) ꢀ
[04] (oldest).
When an error occurred in the air conditioner, an error code
and indoor UNIT No. appear on the display part of the remote
controller.
The error code is only displayed during the operation.
If the display disappears, operate the air conditioner
according to the following “Confirmation of error log” for
confirmation.
REQUIREMENT
Do not push button because all the error log of the indoor
unit will be deleted.
Procedure 3
After confirmation, push
display.
button to return to the usual
Error code
Indoor UNIT No. in
which an error occurred
Confirmation of error log
When an error occurred on the air conditioner, the error log
can be confirmed with the following procedure. (The error
history is stored in memory up to 4 errors.)
The log can be confirmed from both operating status and stop
status.
EN
2
3
1
Procedure 1
When pushing
and
buttons at the same time for 4
seconds or more, the following display appears.
If is displayed, the mode enters in the error log mode.
• [01: Order of error log] is displayed in CODE No..
• [Error code] is displayed in CHECK.
• [Indoor unit address in which an error occurred] is
displayed in Unit No..
– 38 –
38-EN
Installation Manual
Concealed Duct High Static Pressure
Error codes and parts to be checked
Wired remote
controller
display
Air conditioner
status
Main defective parts
Judging device
Parts to be checked / error description
Indication
Incorrect remote controller setting --- The header remote controller has
not been set (including two remote controllers).
No header remote controller
Remote
controller
E01
*
Remote controller
communication error
No signal can be received from the indoor unit.
Remote controller transmission
error
Remote
controller
System interconnecting wires, indoor P.C. board, remote controller
--- No signal can be sent to the indoor unit.
E02
E03
*
Indoor unit-remote controller
regular communication error
Remote controller, network adapter, indoor P.C. board --- No data is
received from the remote controller or network adapter.
Indoor
Indoor
Indoor
Auto-reset
Indoor unit-outdoor unit serial
communication error
System interconnecting wires, indoor P.C. board, outdoor P.C. board -
-- Serial communication error between indoor unit and outdoor unit
E04
E08
Auto-reset
Auto-reset
IPDU-CDB communication error
Duplicated indoor addresses
Indoor address setting error --- The same address as the self-address
was detected.
Remote controller address setting error --- Two remote controllers are
set as header in the double-remote controller control.
Duplicated header remote
controllers
Remote
controller
E09
*
(* The header indoor unit stops raising alarm and follower indoor units
continue to operate.)
Indoor P.C. board --- Communication error between main MCU and
motor microcomputer MCU
E10
E18
CPU-CPU communication error Indoor
Header indoor unit-indoor
Auto-reset
Auto-reset
Indoor P.C. board --- Regular communication is not possible between
header and follower indoor units or between twin header (main) and
follower (sub) units.
follower unit regular
communication error
Indoor
E31
F01
IPDU communication error
Outdoor
Indoor
Communication error between IPDU and CDB
Entire stop
Auto-reset
Indoor unit heat exchanger
sensor (TCJ) error
Heat exchanger sensor (TCJ), indoor P.C. board --- Open-circuit or
short-circuit of the heat exchanger sensor (TCJ) was detected.
Indoor unit heat exchanger
sensor (TC) error
Heat exchanger sensor (TC), indoor P.C. board --- Open-circuit or
short-circuit of the heat exchanger sensor (TC) was detected.
F02
F04
Indoor
Auto-reset
Entire stop
Outdoor unit discharge temp.
sensor (TD) error
Outdoor temp. sensor (TD), outdoor P.C. board --- Open-circuit or
short-circuit of the discharge temp. sensor was detected.
Outdoor
Outdoor unit temp. sensor (TE/
TS) error
Outdoor temp. sensors (TE/TS), outdoor P.C. board --- Open-circuit or
short-circuit of the heat exchanger temp. sensor was detected.
F06
F07
F08
Outdoor
Outdoor
Outdoor
Entire stop
Entire stop
TL sensor error
TL sensor may be displaced, disconnected or short-circuited.
Outdoor unit outside air temp.
sensor error
Outdoor temp. sensor (TO), outdoor P.C. board --- Open-circuit or
short-circuit of the outdoor air temp. sensor was detected.
Operation
continued
Indoor unit room temp. sensor
(TA) error
Room temp. sensor (TA), indoor P.C. board --- Open-circuit or short-
circuit of the room temp. sensor (TA) was detected.
F10
F12
F13
F15
F29
F31
Indoor
Auto-reset
Entire stop
Entire stop
Entire stop
Auto-reset
Entire stop
TS (1) sensor error
Outdoor
Outdoor
Outdoor
Indoor
TS (1) sensor may be displaced, disconnected or short-circuited.
Abnormal temperature was detected by the temp. sensor of the IGBT
heat sink.
Heat sink sensor error
Temp. sensor connection error
Temp. sensor (TE/TS) may be connected incorrectly.
Indoor P.C. board --- EEPROM error
Indoor unit, other P.C. board
error
Outdoor unit P.C. board
Outdoor
Outdoor P.C. board ---- In the case of EEPROM error.
Current detect circuit, power voltage --- Minimum frequency was
reached in the current releasing control or short-circuit current (Idc)
after direct excitation was detected
Outdoor unit compressor
breakdown
H01
Outdoor
Entire stop
H02
H03
H04
Outdoor unit compressor lock
Outdoor
Outdoor
Outdoor
Compressor circuit --- Compressor lock was detected.
Entire stop
Entire stop
Entire stop
Outdoor unit current detect circuit
error
Current detect circuit, outdoor unit P.C. board --- Abnormal current was
detected in AC-CT or a phase loss was detected.
Case thermostat operation (1)
Malfunction of the case thermostat
Current, high-pressure switch circuit, outdoor P.C. board --- Ps
pressure sensor error was detected or low-pressure protective
operation was activated.
Outdoor unit low-pressure
system error
H06
Outdoor
Entire stop
Duplicated header indoor units
Indoor address setting error --- There are two or more header units in
the group.
L03
L07
Indoor
Indoor
Entire stop
Entire stop
Group line in individual indoor
unit
Indoor address setting error --- There is at least one group-connected
indoor unit among individual indoor units.
L08
L09
L10
Indoor group address not set
Indoor power level not set
Outdoor unit P.C. board
Indoor
Indoor
Outdoor
Indoor address setting error --- Indoor address group has not been set. Entire stop
Indoor power level has not been set. Entire stop
In the case of outdoor P.C. board jumper wire (for service) setting error Entire stop
39-EN
– 39 –
Installation Manual
Concealed Duct High Static Pressure
Wired remote
controller
display
Air conditioner
status
Main defective parts
Judging device
Parts to be checked / error description
Indication
Network
adapter central
control
Address setting, central control remote controller, network adapter ---
Duplication of address in central control communication
L20
LAN communication error
Auto-reset
Entire stop
Other outdoor unit error
1) Communication error between IPDU MCU and CDB MCU
L29
Other outdoor unit error
Outdoor
Entire stop
2) Abnormal temperature was detected by the heat sink temp. sensor
in IGBT.
Abnormal external input into
indoor unit (interlock)
External devices, outdoor unit P.C. board --- Abnormal stop due to
incorrect external input into CN80
L30
L31
Indoor
Entire stop
Operation
Power supply phase sequence, outdoor unit P.C. board --- Abnormal continued
Phase sequence error, etc.
Outdoor
phase sequence of the 3-phase power supply
(thermostat
OFF)
Indoor fan motor, indoor P.C. board --- Indoor AC fan error (fan motor
thermal relay activated) was detected.
P01
P03
P04
P05
P07
P10
P15
Indoor unit fan error
Indoor
Entire stop
Entire stop
Entire stop
Entire stop
Entire stop
Entire stop
Entire stop
Outdoor unit discharge temp.
error
Outdoor
Outdoor
Outdoor
Outdoor
Indoor
An error was detected in the discharge temp. releasing control.
Outdoor unit high-pressure
system error
High-pressure switch --- The IOL was activated or an error was
detected in the high-pressure releasing control using the TE.
The power supply wire may be connected incorrectly. Check open
phase and voltages of the power supply.
Open phase detected
Heat sink overheat
Abnormal temperature was detected by the temp. sensor of the IGBT
heat sink.
Indoor unit water overflow
detected
Drain pipe, clogging of drainage, float switch circuit, indoor P.C. board
--- Drainage is out of order or the float switch was activated.
There may be gas leakage from the pipe or connecting part. Check for
gas leakage.
Gas leakage detected
4-way valve error
Outdoor
EN
4-way valve, indoor temp. sensors (TC/TCJ) --- An error was detected
due to temperature drop of the indoor unit heat exchanger sensor
when heating.
Outdoor
(Indoor)
Auto-reset
(Auto-reset)
P19
P20
P22
High-pressure protective
operation
Outdoor
Outdoor
High-pressure protection
Entire stop
Entire stop
Outdoor unit fan motor, outdoor unit P.C. board --- An error
(overcurrent, locking, etc.) was detected in the outdoor unit fan drive
circuit.
Outdoor unit fan error
IGBT, outdoor unit P.C. board, inverter wiring, compressor --- Short-
circuit protection for compressor drive circuit devices (G-Tr/IGBT) was Entire stop
activated.
Outdoor unit inverter Idc
activated
P26
P29
P31
Outdoor
Outdoor
Indoor
Outdoor unit P.C. board, high-pressure switch --- Compressor motor
position error was detected.
Outdoor unit position error
Other indoor unit error
Entire stop
Another indoor unit in the group is raising an alarm.
Entire stop
Auto-reset
E03/L07/L03/L08 alarm check locations and error description
: The air conditioner automatically enters the auto-address setting mode.
– 40 –
40-EN
|