Toshiba Ras 10sa E User Manual

9. TROUBLESHOOTING CHART ..................................................................................... 32

9-1. What to be Prechecked First .................................................................................................. 32

9-1-1. Power Supply Voltage...........................................................................................................................32

9-1-2. Incorrect Cable Connection between Indoor and Outdoor Units .....................................................32

9-1-3. Misleading but Good Operations.........................................................................................................33

9-2. Primary Judgement of Trouble Sources ............................................................................... 34

9-2-1. Role of Indoor Unit Controller..............................................................................................................34

9-2-2. Display of Abnormalities and Judgement of the Abnormal Spots ...................................................34

9-3. Troubleshooting Flowcharts................................................................................................... 38

9-3-1. Power can not be Turned on ................................................................................................................38

9-3-2. Power can not be Turned on after Replacing Indoor PC Board .......................................................39

9-3-3. Outdoor Unit does not Operate ...........................................................................................................39

9-3-4. Only Compressor does not Operate ...................................................................................................40

9-3-5. Only Outdoor Fan does not Operate ...................................................................................................41

9-3-6. Only the Indoor Fan does not Operate................................................................................................42

9-4. How to Check the Remote Control (Including the Indoor PC Board) ................................ 43

9-4-1. How to Check the PC Board.................................................................................................................44

9-4-2. PC Board Layout ...................................................................................................................................46

9-4-3. How to Reduce the Operation Time of the Anti-Restart Timer .........................................................47

10. PART REPLACEMENT ................................................................................................. 48

10-1. Indoor Unit ................................................................................................................................ 48

10-2. Microcomputer ......................................................................................................................... 50

10-3. Outdoor Unit ............................................................................................................................. 51

11. CAUTIONS ON REPLACEMENT OF PC BOARD ASSEMBLY.................................... 52

12. EXPLODED VIEWS AND PARTS LIST........................................................................ 53

12-1. Indoor Unit (1)........................................................................................................................... 53

Indoor Unit (2)........................................................................................................................... 54

12-2. Outdoor Unit ............................................................................................................................. 55

– 3 –

1. SPECIFICATIONS

RAS-10SK-E/10SA-E

RAS-10SKX/10SAX

Model

Item

COOLING

240V 220V

2.70 2.70

Single

220V

2.65

230V

2.65

230V

2.70

240V

2.70

Capacity

*1 kW

Phase

Power source

220/230/240

Power consumption

Power factor

0.83/0.85/0.88

95/92/90

230V

220V

0.15/3.82

240V

0.15/3.92

Running current

Indoor/Outdoor

0.15/3.87

Starting current

Moisture removal

lit/h

1.2

Indoor (H/M/L)

44/36/31

44/45/45

R-22

Noise

Outdoor (220/230/240V)

Name of refrigerant

Rated volume

Refrigerant

0.73

Refrigerant control

Capillary tube

9.52

Gas side size

Connection type

Liquid side size

Connection type

Flare connection

6.35

Flare connection

Interconnection pipe

Maximum length (of one way) m

Maximum height difference

Indoor unit

↑

↓

Outdoor unit

Condensate drain pipe Outer diameter

INDOOR UNIT

RAS-10SK-E/RAS-10SKX

Height

265

Dimensions

Width

Depth

790

174

Net weight

Evaporator type

Indoor fan type

Finned tube

Cross flow fan

High fan

m /h

650

Air volume

Medium fan

Low fan

m /h

510

m /h

430

Fan motor output

Air filter

Polypropylene net filter (Washable)

OUTDOOR UNIT

RAS-10SA-E/RAS-10SAX

Height

Width

Depth

530

Dimensions

770

200

Net weight

Finned tube

Propeller

1600

Condenser type

Outdoor fan type

Airflow volume

Fan motor output

m /h

Model

PH102T1-4C

750

Compressor

Output

Safety device

Auto louver

Fuse, Overload relay

Ye s

Usable outdoor temperature range

°C

21 ~ 43

Specifications are subject to change without notice.

– 4 –

Note : *1

• Capacity is based on the following temperature conditions.

Condition

JIS C9612-1994

Cooling

27°C

Temperature

(DB)

Indoor unit inlet air temperature

(WB)

19°C

(DB)

Outdoor unit inlet air temperature

(WB)

35°C

24°C

Notes : *2 CHARGELESS

• No additional refrigerant required.

• This air conditioner accepts a connection piping length of up to 10m and a head of up to 5m.

• There is no need to add the refrigerant as long as the total length of the connection piping is up to 10m.

– 5 –

2. CONSTRUCTION VIEWS

2-1. Indoor Unit

RAS-10SK-E

RAS-10SKX

Heat exchanger

Air inlet

Air filter

790

174

10SK-E : Without power cord

10SKX : With power cord

1800

Air outlet

Knock out system

790

Front panel

Back body

232

326

Hanger

232

Drain hose (0.54m)

Hanger

321

Knock out system

Connecting pipe (0.39m)

(Flare ø9.52)

Connecting pipe (0.49m)

(Flare ø6.35)

65.5

659

65.5

Hanger

Wireless

remote

control

450

326

66 or more

For stud bolt

(ø8~ø10)

Hanger

Minimum

distance

to ceiling

For stud bolt

(ø6)

Minimum

Remote

control

holder

Minimum

distance to wall

distance

to wall

120 or more

Hanger

Center line

Hanger

Installation

plate outline

59.6

60.5

126

319

269

790

– 6 –

2-2. Outdoor Unit

RAS-10SA-E

RAS-10SAX

600

111

Detail Drawing

Gas side (flare ø9.52)

ø25 Drain hole

600

R10

Liquid side (flare ø6.35)

200

ø6 Hole

ø11x14 Hole

Handle

8-ø6 Holes

(For fixing the outdoor unit)

4-ø11x14 Long holes

(For anchor bolt ø8-ø10)

111

Fan guard

ø420

TOSHIBA

Electric

parts cover

Access for

charging

250

770

View

600

Inlet port

600 or more

Inlet port

100 or more

Visible outline

of the product

(Minimum distance

of the wall)

4-ø11x14 Long holes

(For anchor bolt ø8-ø10)

Outlet

port

Center

port

Mounting dimension of anchor bolt

– 7 –

3. WIRING DIAGRAM

Model

Section A

LOUVER

MOTOR

RAS-10SK-E/SA-E

220/230/240V ~

50Hz

FAN MOTOR

MOTOR

THERMAL FUSE

77˚C x 2

RAS-10SKX/SAX

220/230/240V ~

50Hz

6 5 4 3

5 4 3

2 1

5 4 3 2

CN04

CN07

CN10

SG01

R109

MAIN P.C. BOARD

MCC-713

BLK

GRN&YEL

R116

IC04

DSA

VARISTOR

P04

F01 FUSE

R01

C01

DB01

BRW

BLU

T01

T3.15A

250V

C02

Section A

DC 35V

C15

R21

RY01

POWER

TERMINAL

BLOCK

L01

DC 12V

RY02

DC 7V

DC 0V

BLK

WHI

C06

IC02

IC01

4 5 6 7 8 9

1 2

1 2 3

CN03

CN01

CN13

CN25

4 5 6 7 8 9

1 2 3

INFRARED RAYS RECEIVE

AND INDICATION PARTS

HEAT

THERMO

SENSOR

(TA)

EXCHANGER

SENSOR

(TC)

INDOOR

TERMINAL

BLOCK

INDOOR

DSA : Surge absorber

OUTDOOR

TERMINAL

BLOCK

COLOR IDENTIFICATION

GRN & YEL

CHASSIS

BRW : BROWN

RED : RED

WHI : WHITE

YEL : YELLOW

BLU : BLUE

BLK : BLACK

GRY : GRAY

PNK : PINK

BLK

OVER LOAD

RELAY

RED

RUNNING

CAPACITOR

RUNNING

CAPACITOR

RED

BLK BLK

FAN MOTOR

RED

WHI

COMPRESSOR

ORN : ORANGE

PNK

WHI

GRN&YEL : GREEN &

YELLOW

– 8 –

4. SPECIFICATIONS OF ELECTRICAL PARTS

4-1. Indoor Unit

RAS-10SK-E

RAS-10SKX

No.

Parts name

Type

Specifications

ICF-35-19-3

DC 35V, 19W

Fan motor (for indoor)

TICF-35-19-3

Thermo sensor

(TA-sensor)

(microprocessor)

10kΩ at 25°C

DC-DC transformer (T01)

Microcomputer

SWT-34

DC390V, Secondary DC35V, 12V, 7V

TMP87CK40F

Power relay (RY01), Com-

mon relay (RY02)

DI1U

Coil : DC12V 75mA, Rated AC250V 20A

Heat exchanger sensor

(TC-sensor)

(microprocessor)

10kΩ at 25°C

Line filter (L01)

Diode (DB01)

RF-103YOR6

RBV-406

10mH, AC 0.6A

4A, 600V

Capacitor (C02)

Fuse (F01)

CEAUF2W101M20 100µF, 450V

T3.15A, 250V

MT3

Power supply IC (IC01)

Varistor (R21, R109)

Resistor (R01)

Louver motor

MA2830-FJ

15G561K

4A, 600V

560V

ERF-5TK5R6

MP35EA7

5.6 Ω, 5W

Output (Rated) 2W, 10poles, 1phase DC 12V

4-2. Outdoor Unit

RAS-10SA-E

RAS-10SAX

No.

Parts name

Type

Specifications

Output (Rated) 750W, 2pole, 1phase, 220/230/240V, 50Hz

Red-Black

3.88

White-Black

5.06

Compressor

PH102T1-4C

Winding resistance (Ω)

(at 20°C)

Output (Rated) 18W, 6pole, 1phase, 220/230/240V, 50Hz

Red-Black

370

White-Black

370

Fan motor (for outdoor)

UE6-21SJ5P

SK-50FMP

Winding resistance (Ω)

(at 20°C)

Running capacitor

(for fan motor)

500V AC, 1.5µF

Running capacitor

(for compressor)

SK-40CMP25U1

400V AC, 25µF

J-MRA99285-9201

Overload relay

U/T 6.1A (80°C), OPEN 135±5°C, CLOSE 78±11°C

– 9 –

5. REFRIGERANT CYCLE DIAGRAM

RAS-10SK-E / RAS-10SA-E

RAS-10SKX / RAS-10SAX

Indoor unit

Evaporator

Cooling

0.39m

0.49m

(Connecting pipe)

ø9.52

(Connecting pipe)

ø6.35

Cross flow fan

Optional piping kits

RB-P31BFH1 (3m)

RB-P51BFH1 (5m)

RB-P71BFH1 (7m)

O.D.:9.52mm

O.D.:6.35mm

Packed valve

(ø6.35)

(ø9.52)

Capillary tube

ø1.5x1200

Accumulator

Compressor

PH102T1-4C

Dryer

Condenser

Refrigerant

R-22 0.73kg

Propeller fan

Outdoor unit

Mark (

) means check points of Gas Leak

Fig. 5-1

Table 5-1

Standard pressure

Surface temp. of heat

exchanger interchanging

pipe T1 (°C)

Ambient temp.

conditions DB/WB

(°C)

Fan speed

(indoor)

(kg/cm²G)

10SK-E

50Hz

10SK-E

10SKX

5.0

10SKX

13.0

18.0

2.0

Indoor Outdoor

Standard

High

Low

27/19

32/23

21/15

35/24

43/26

21/15

Cooling High temperature

Low temperature

6.5

4.0

Note :

• Measure the heat exchanger temperature at the center of U-bend. (By means of TC sensor.)

– 10 –

6. MICRO-COMPUTER BLOCK DIAGRAM

– 11 –

7. OPERATION DESCRIPTIONS

7-1. FAN ONLY Operation

7-2. COOL Operation

(MODE of the remote control : FAN ONLY)

(MODE of the remote control : COOL)

(1) During this mode, the relay RY01 is always turned

off so that only the indoor fan is operated. RY02

is always turnd on. FAN-ONLY display is lit.

(1) Compressor, outdoor fan and operation display

are controlled as shown in Fig. 7-2-1.

1) When the FAN is set to AUTO, the indoor fan

motor operates as shown in Fig 7-1-1.

2) When the FAN is set to LOW, MED, or HIGH,

the indoor fan motor operates with a constant

in volume as listed in Table 7-1-1.

OFF

Set

temp.

HIGH

MED

LOW(+)

Fig. 7-2-1

LOW

(2) Relays RY01 and RY02 are turned on to energize

the outdoor unit, and a cool operation is carried

out.

LOW

Fig. 7-1-1 Auto setting of air volume

1) When the FAN is set to AUTO, the indoor fan

motor operates as shown in Fig 7-2-2.

Table 7-1-1 Manual setting of FAN SPEED

2) When the FAN is set to LOW, MED, or HIGH,

the indoor fan motor operates with a constant

in volume as listed in Table 7-1-1.

HIGH Air volume

(m³/h)

Indication of

FAN SPEED

LOW

MED

HIGH

430

510

650

FAN

AUTO

HIGH

Manual

MED

LOW(+)

LOW

According

to the set

position

(2) Once the setting is made, the operation mode is

memorized in the microcomputer so that the same

operation can be effected thereafter simply by

pushing the START/STOP button.

LOW

(continuous)

Set

temp.

RY01

OFF

Fig. 7-2-2

(3) Once the setting is made, the operation mode is

memorized in the microcomputer so that the same

operation can be effected thereafter simply by

pushing the START/STOP button.

– 12 –

7-2-1. Louver Control

7-3. DRY Operation

(1) By pushing the SET button of the remote control

during the operation, the louver can be set to the

desired position.

(MODE of the remote control : DRY)

(1) Compressor, outdoor fan and operation display

are controlled as shown in Fig. 7-3-1.

And the louver position is stored in the microcom-

puter, the louvers will be set to the position au-

tomatically at the next operation.

(2) When the AUTO button is pushed, the louver ver-

tically swings within range of 25deg.

OFF

Set

temp.

Fig. 7-3-1

•

The microprocessor turns the compressor on

and off at regular intervals (4 to 6 minutes on

and/or off). During the compressor off, the

indoor fan will operate in the super low position.

•

The indoor fan will operate in the AUTO

position.

(2) The pattern of operation depending on the relation

between room temperature and set temperature

is shown below:

Room temp.

Set temp.+1

Set temp.

Compressor

Outdoor fan

OFF

S.L.

OFF

S.L.

Indoor fan

L. *S.L. L.

*Super Low

Fig. 7-3-2

– 13 –

7-4-1. Temporary Auto

7-4. AUTO Operation

When the TEMPORARY button is pushed, the set

temperature is fixed at 24°C and controlled in accor-

dance with the chart shown in Fig. 7-4-1.

(MODE of the remote control : AUTO)

(1) One of the 2 modes, Cooling or Dry is selected

according to room temperature at which operation

is to start, as shown in Fig. 7-4-1. The Fan mode

will continue until room temperature reaches a

level at which another mode is selected.

Cooling mode (The same cooling mode as the room temperature control is set at set temp. –1˚C)

The Louver moved downward.

Cooling mode (The same cooling mode as the room temperature control is set at set temp. –1˚C)

Dry mode

(The same dry operation as the room temperature control is set at set temp. –1˚C)

Fig. 7-4-1

– 14 –

7-5. ECONO. Mode

7-6. Low-Temperature Limit Control

(Cooling Operation)

When the ECONO. button is pushed, during COOL

and AUTO operation, the OPERATION display is

turned off and the ECONO. display is lit and the indoor

unit operates quietly and mildly with controlling airflow.

The microprocessor detects the indoor heat exchanger

temperature so as to prevent freezing up the indoor

heat exchanger.

Control is performed as shown in Fig. 7-6-1.

7-5-1. Cooling

(1) In the ECONO. mode, the set temp. by the remote

control is changed automatically as shown in Fig.

7-5-1.

Heat exchanger

temperature

Compressor

Outdoor fan

(˚C)

(2) Fan speed → LOW

Less than 5˚C continues

for 5 minutes

OFF

(˚C)

Set temp.

is changed

Set temp.

is changed

Fig. 7-6-1

TIME

Set temp.

ECONO. button

is pushed

Fig. 7-5-1

– 15 –

7-7-1. How to Set the Auto Restart

7-7. Auto Restart Function

To set the Auto Restart function, proceed as follows:

This unit is equipped with an Automatic restarting

facility which allows the unit to restart and resume the

set operating conditions in the event of a power supply

shutdown without the use of the hand control.

Access the TEMPORARY button located in the lower

right hand corner beneath the hinged front panel of

the indoor unit (please refer to section on PARTS

NAME). The power supply to the unit must be on -

the function will not be set if the power is off.

The operation will resume without warning three

minutes after the power is restored.

To enable the Auto Restart function, press the

TEMPORARY button continuously for three seconds.

The Auto Restart function is set not to work on

shipment from the factory, and so it is necessary to

set it to function as required.

The unit will acknowledge the setting and beep three

times. The system will now restart automatically.

The above Auto Restart settings can be carried out:

• When the system is stand-by (not running)

OPERATION

MOTION

Press the TEMPORARY button

continuously more than three

seconds.

Stand-by

↓

The system starts to operate.

The green light will be lit.

about three seconds after

The orange light will be lit.

↓

The unit beeps three times.

↓

The system is operating.

The orange light is lighting.

TEMPORARY

If the system is not required to run at this time, press theTEMPORARY

button once more or use the remote control and the unit will stop.

• When the system is operating

OPERATION

MOTION

Press the TEMPORARY button

continuously more than three

seconds.

Operating

The green light is lit.

↓

The system stops to operate.

The green light is turned off.

about three seconds after

↓

The unit beeps three times.

↓

The system stops.

TEMPORARY

If the system is not required to stop at this time, use the remote control

and to restart.

During subsequent operation, the orange light is lit.

• During louver swing (AUTO) operation, after restart

by the Auto Restart function the louver swing stops.

• The Auto Restart function will not accept an

instruction if timer operation with the remote control

is selected.

(Please refer to the section on setting the timer or

setting the louver.)

– 16 –

7-7-2. How to Cancel the Auto Restart

The system will now be required to manually restart

with the remote control after the main supply is turned

off.

To cancel the Auto Restart function, proceed as

follows:

Cancellation is carried out:

Repeat the setting procedure: the unit will

acknowledge the instruction and bleep three times.

• When the system is stand-by (not running)

OPERATION

MOTION

Press the TEMPORARY button

continuously more than three

seconds.

Stand-by

↓

The system starts to operate.

The orange light will be lit.

about three seconds after

The green light will be lit.

↓

The unit beeps three times.

↓

The system is operating.

TEMPORARY

If the system is not required to run at this time, press theTEMPORARY

button once more or use the remote control and the unit will stop.

• When the system is operating

OPERATION

MOTION

Press the TEMPORARY button

continuously more than three

seconds.

Operating

The orange light is lit.

↓

The system stops to operate.

The orange light is turned off.

about three seconds after

↓

The unit beeps three times.

↓

The system stops.

TEMPORARY

If the system is not required to stop at this time, use the remote control

and to restart.

During subsequent operation, the green light is light-

ing.

7-7-3. In Case of Power Failure during the

Timer Operation

(2) If OFF-TIMER operation is reserved without

setting of Auto Restart operation, the reservation

is cancelled with power failure. (The OPERATION

lamp on the main unit goes on and off to inform of

power failure.) In that case, try to reserve OFF-

TIMER operation. When Auto Restart operation

is set, OFF-TIMER reservation is also cancelled

with power failure.

(1) If ON-TIMER operation is reserved with setting of

Auto Restart operation, it is cancelled with power

failure. (The OPERATION lamp on the main unit

goes on and off to inform of power failure.) In that

case, try to reserve ON-TIMER operation once

again.

– 17 –

8. INSTALLATION PROCEDURE

8-1. Safety Cautions

For general public use

Power supply cord of parts of appliance for Outdoor use shall be more than polychloroprene sheathed flexible

cord (design H05 RN-F), or cord designation 245 IEC 57.

CAUTION

TO DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY.

This appliance must be connected to the mains by means of a circuit breaker or a switch with a contact

separation of at least 3 mm.

If this is not possible, a power supply plug with earth must be used. This plug must be easily accessible after

installation. The plug must be disconnected from the power supply socket in order to disconnect the appliance

completely from the mains.

DANGER

` FOR USE BY QUALIFIED PERSONS ONLY.

` TURN OFF MAIN POWER SUPPLY AND BREAKER BEFORE ATTEMPTING ANY ELECTRICAL WORK.

MAKE SURE ALL POWER SWITCHES AND BREAKER TURN OFF. FAILURE TO DO SO MAY CAUSE

ELECTRICAL SHOCK.

` CONNECT THE CONNECTING CABLE CORRECTLY. IF THE CONNECTING CABLE IS CONNECTED BY

WRONG WAY, ELECTRIC PARTS MAY BE DAMAGED.

` CHECK THE EARTH WIRE IS NOT BROKEN OR DISCONNECTED BEFORE INSTALLATION.

` DO NOT INSTALL NEAR CONCENTRATIONS OF COMBUSTIBLE GAS OF GAS VAPORS.

FAILURE TO FOLLOW THIS INSTRUCTION CAN RESULT IN FIRE OR EXPLOSION.

` TO PREVENT OVERHEATING THE INDOOR UNIT AND CAUSING A FIRE HAZARD, PLACE THE UNIT

WELL AWAY (MORE THAN 2M.) FROM HEAT SOURCES SUCH AS RADIATORS, HEAT RESISTORS,

FURNACE, STOVES, ETC..

` WHEN MOVING THE AIR-CONDITIONER FOR INSTALLING IT IN ANOTHER PLACE AGAIN, BE VERY

CAREFUL NOT TO GET THE SPECIFIED REFRIGERANT (R-22) WITH ANY OTHER GASEOUS BODY

INTO THE REFRIGERATION CYCLE. IF AIR OR ANY OTHER GAS IS MIXED IN THE REFRIGERANT,

THE GAS PRESSURE IN THE REFRIGERATION CYCLE BECOMES ABNORMALLY HIGH AND IT

RESULTINGLY CAUSES BURST OF THE PIPE AND INJURIES ON PERSONS.

` IN THE EVENT THAT THE REFRIGERANT GAS LEAKS OUT OF THE PIPE DURING THE INSTALLATION

WORK, IMMEDIATELY LET FRESH AIR INTO THE ROOM. IF THE REFRIGERANT GAS IS HEATED BY

FIRE OR SOMETHING ELSE, IT CAUSES GENERATION OF POISONOUS GAS.

WARNING

• Never modify this unit by removing any of the safety guards or by by-passing any of the safety interlock

switches.

• Do not install in a place which cannot bear the weight of the unit.

Personal injury and property damage can result if the unit falls.

• Before doing the electrical work, attach an approved plug to the power supply cord.

And make sure the equipment to be earthed.

• Appliance shall be installed in accordance with national wiring requlations.

If you detect any damage, do not install the unit. Contact your Toshiba dealer immediately.

– 18 –

CAUTION

• Exposure of unit or water or other moisture before installation will result in an electrical short.

Do not store in a wet basement or expose to rain or water.

• After unpacking the unit, examine it carefully for possible damage.

• Do not install in a place that can increase the vibration of the unit. Do not install in a place that can amplify

the noise level of the unit or where noise and discharged air might disturb user’s neighbors.

• To avoid personal injury, be careful when handling parts with sharp edges.

• Please read the installation manual carefully before installing the unit. It contains further important

instructions for proper installation.

UK Plugs and Sockets etc (Safety) Regulations 1994

SI Number 1768

With regard to Schedule 3, Item 7 of the above UK Regulations, this appliance must be permanently connected to

the fixed wiring of the main electrical supply by means other than the use of an approved 13 Amp plug-top

as outlined in the Regulations.

Electrical work must be carried by suitably qualified persons and in accordance with all relevant safety standards

and codes of practice.

We recommend that the power supply for this appliance is derived from a suitably protected dedicated circuit.

(for U.K. only)

– 19 –

8-2. Installation Diagram of Indoor and Outdoor Units

For installation of the indoor unit, use the paper pattern on the back.

For the rear and left piping

Clip aanchor

Wall

Hook

Front cabinet

Front panel

Installation

plate

Insert the remote control holder

cushion between the indoor

unit and wall, and lift indoor

unit to make work easier.

Hook

Do not allow the drain hose to

get slack.

Mounting screw

Cut the piping hole

sloped slightly

Shield pipe

Filter

Pan head

wood screw

Make sure to run the drain

hose sloped downward.

frame

Deodorizing

filter

The auxiliary piping can be

connected the left, rear left,

rear, right or bottom.

Remote control

holder

10 Purifying

filter

Wireless

remote

control

Right

Rear

Rear left

Before install the wireless

remote control

Left

Bottom

Extension

drain hose

(Option:

• With the remote control cover

open, load the batteries

supplied correctly, observing

their polarity.

Insulation of refrigerant pipes

insulates the pipes separately,

not together.

RB-821SW)

2 Wireless remote control

Electric parts

cover

Batteries

Loop the connective cable

(about 100 mm in diameter

and 300~350 mm long).

6 mm thick heat resisting

polyethylene foam

Cover

– 20 –

8-3. Installation

600mm

Air inlet

8-3-1. Optional Parts

Part

code

Parts name

Q’ty

Refrigerant piping

Each

one

Liquid side : ø6.35 mm

Gas side : ø9.52 mm

Pipe insulating material

(polyethylene foam, 6 mm thick)

Air outlet

Fig 8-3-1 Air outlet

Each

one

Putty, PVC tapes

• Secure the outdoor unit with the anchor bolts if the

unit is likely to be exposed to a strong wind.

• Use ø8 or ø10 anchor bolts.

8-3-2. Installation Parts

Part

No.

Name of parts

Q’ty

Part

No.

Name of parts

Q’ty

Part

No.

Name of parts

Q’ty

Installation plate x 1

Shield pipe x 1

Deodorizing filter x 1

Purifying filter x 1

Filter frame x 2

Pan head wood screw

ø3.1 x 16l x 2

Wireless remote control x 1

Clip anchor x 6

Batteries x 2

Remote control holder x 1

Mounting screw ø4 x 25l x 6

This model is not equipped with an extension drain

hose.

Others

Name

Installation manual

Owner’s manual

Option : For the extension drain hose, use an optionally

available RB-821SW or commercially available one.

– 21 –

8-4-1. Cutting a Hole and Mounting

Installation Plate

8-4. Indoor Unit

t Installation place

• A place which provides the spaces around the

indoor unit as shown in the diagram in section 8-2.

When installing the refrigerant pipes from the rear

• A place where there is no obstacle near the air

inlet and outlet.

• A place which allows an easy installation of the

piping to the outdoor unit.

• A place which allows the front panel to be opened.

The center of the piping slot

is the above arrow.

CAUTION

The center of the pipe

• Direct sunlight to the indoor unit wireless

receiver should be avoided.

hole is the above arrow.

Pipe hole

80mm

• The microprocessor in the indoor unit should

not be too close to r-f noise sources. (For

details, see the owner’s manual.)

Fig. 8-4-2

(1) After determining the pipe hole position with the

mounting plate (80 mm→), drill the pipe hole (ø65

mm) at a slight downward slant to the outdoor side.

• A place where there are no obstacles such as a

curtain that may block the signal from the remote

control.

NOTE :

• When drilling the wall that contains a metal lath,

wire lath or metal plate, be sure to use a pipe hole

brim ring sold separately.

• Do not install the remote control in a place exposed

to direct sunlight or close to a heating source, such

as a stove.

• Keep the remote control at least 1 m apart from

the nearest TV set or stereo equipment. (This is

necessary to prevent image disturbances or noise

interference.)

For installation of the indoor unit, use the paper pattern

on the back.

• The location of the remote control should be

determined as shown below.

Anchor bolt hole

65.5mm

(Top view)

Indoor unit

45˚

65.5mm

Pipe

hole

Pipe hole

Reception

Remote

Installation

plate

Thread

Remote

control

Reception

range

8 Mounting

screw

control

Indoor unit

Weight

*:Axial distance

Fig. 8-4-1

Fig. 8-4-3

– 22 –

8-4-2. Electrical Work

<When the installation plate is directly mounted

on the wall>

(1) The supply voltage must be the same as the rated

voltage of the air conditioner.

(1) Securely fit the installation plate onto the wall by

screwing it in the upper and lower parts to hook

up the indoor unit.

(2) Prepare the power source for exclusive use with

the air conditioner.

(2) Install the installation plate horizontally in the wall.

Plug

socket

& fuse

rating

Maximum

running

current

(3) To mount the installation plate on a concrete wall

with anchor bolts, utilize the anchor bolt holes as

shown in the above figure.

Model

Power source

Wiring

RAS-

10SK-E/

10SA-E

RAS-

10SKX/

10SAX

50Hz

*220/230/240V~

Single-phase

1mm²

CAUTION

7.5 A

16 A

When installing the installation plate with mounting

screw, do not use the anchor bolt hole. Otherwise

the unit may fall down and result in personal injury

and property damage.

* No adjustment is necessary.

CAUTION

Installation plate

(Keep horizontal direction)

Anchor bolt

• Use power specified in above table.

• This appliance can be connected to the mains

in either of the following two ways.

Projection

15mm

or less

(1) Connecting the power cord to the main power

supply provided with a circuit breaker or switch

with a contact of 3 mm or more.

5mm dia, hole

3 Clip anchor

In this case, an approved circuit breaker or

switch must be used.

(2) Attaching a plug to the power cord and pluging

it in to the wall outlet.

In this case, an approved power cord and plug

must be used.

Mounting screw ø4 x 25

NOTE :

• Perform wiring works so as to allow a generous

wiring capacity.

Fig. 8-4-4

CAUTION

Failure to firmly install the unit may result in

personal injury and property damage if the unit

falls.

• In case of block, brick, concrete or similar type

walls, make 5 mm dia, holes in the wall.

• Insert

clip anchors for appropriate

mounting screws.

NOTE :

• Install the installation plate using 4 to 6 pieces of

mounting screw securing four corners with screws.

– 23 –

8-4-3. Wiring Connection

Taking out the power cord

WARNING

To plug the cable in the plug receptacle, take the

following precaution.

Slitted portion

THIS APPLIANCE MUST BE EARTHED.

• Cut off the slitted portion in the side face of the

rear panel to take out the power cord. After

this, remove burrs, sharp edges, etc., to

smooth the cut face.

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLORED

IN ACCORDANCE WITH THE FOLLOWING CODE:

L : Brown

-LIVE

N : Blue

-NEUTRAL

-EARTH

: Green and Yellow

For the air conditioner that has no power cord,

connect a power cord to it as mentioned below.

Fig. 8-4-5

• After removing the front cabinet, remove the

terminal cover and the cord clamp.

As the colors of the flexible cord of this appliance may

not correspond with the colored markings, to identify

terminals in your plug, as follows:

• Connect and secure the power supply cord and

secure the cord clamp and the terminal cover.

Connect BROWN colored core to plug terminal marked

letter "L".

• Cut the rear panel following the cutting mark and

put the power supply cord through the notch.

Connect BLUE colored core to plug terminal marked

letter "N".

• Be sure to smooth out the notch with a file, etc.

Connect GREEN AND YELLOW colored core to plug

Cord clamp

Screw

Terminal block

Terminal cover

Power supply

cord

terminal marked Earth Symbol "

Screw

Vertical air flow louver.

Earth line

Fig. 8-4-6

Screw

Fig. 8-4-7

How to open the screw cap

30mm

10mm

• Place your finger on the lower part and push

up to open the screw cap.

(1) Open the screw caps and remove the two screws

securing the front cabinet.

10mm

40mm

Earth line

(2) Close the screw caps as behind.

(3) Open the vertical airflow louver horizontally by

hand.

NOTE :

• Use standard wire only.

• Wire type: More than H05-RN-F

(4) Slightly open the lower part of the front cabinet

then pull the upper part of the front cabinet toward

you to remove it from the rear plate.

Fig. 8-4-8

– 24 –

Wiring of the connecting cable can be carried out

without removing of the front panel.

50mm

Earth line

10mm

(1) Remove the front panel.

Fully open the front panel. Disengage the support

arm located in the upper center while pushing its

handle leftwards, and then remove the front panel

toward you.

10mm

40mm

(2) Remove the terminal cover and cord clamp.

For a three conductor cable

NOTE :

(3) Insert the connecting cable (according to local

codes) into pipe hole on the wall.

• Use stranded wire only.

• Wire type:More than H05 RN-F

(4) Take out the connecting cable through the cable

slot on the rear panel so that it is exploded by

about 15 cm long in the front side.

Fig. 8-4-10

(5) Insert the connecting cable fully into the terminal

block and secure it by screw tightly.

<How to install the front cabinet on the indoor

unit>

(6) Tightening torque:1.2 N•m (0.12 kgf•m)

Install the front cabinet through the opposite order of

"How to remove the front cabinet".

(7) Secure the connecting cable with the cord clamp.

(8) Fix the terminal cover and front panel on the indoor

unit.

When the panel is removed and mounted again, take

the following actions:

After fastening the two screws, one each at the left

and right of the air outlet, be sure to push the upper

CAUTION

center

right end

, left end

and the lower

• Be sure to refer the wiring system diagram

labeled inside the front panel.

of the air outlet, and confirm that no gap is

left between the front cabinet and the rear plate.

• Check local electrical codes and also any

specific wiring instructions or limitation.

• If cooling (dry) operation is made without

pushing the air outlet, dew can be deposited

on the front cabinet surface. In addition a gap

between the front cabinet and the rear plate

will become wider, spoiling the appearance.

Terminal block

Cord

Terminal

clamp

Push

Connecting

cable

cover

Screw

Earth

line

Screw

Connecting cable

Screw

Push

Fig. 8-4-9

Fig. 8-4-11

– 25 –

8-4-4. Piping and Drain Hose Installation

To connect pipe after installation of unit (figure)

(To the forefront of flare)

• After scribing slits of the front panel and the rear

panel by a knife or a marking-off pin, cut them by a

pair of nippers or the like.

196mm

Side of liquid flow

Side of gas flow

96mm

Outward form of indoor unit

Slit (front panel)

R 30mm (Use polisin or the like for bending pipe.)

80˚

Use the handle of screwdriver,etc.

Slit (rear panel)

Fig. 8-4-14

Fig. 8-4-12

NOTE :

If the pipe is bent incorrectly, the indoor unit may

unstably be set on the wall.

• After scribing the slit of the front panel and slit in

the lower part of the rear panel by a knife or a

marking-off pin, cut them by a pair of nippers or

the like.

After passing the connecting pipe through the pipe

hole, connect the connecting pipe to auxiliary pipes

and wrap the facing tape around them.

CAUTION

• Bind the auxiliary pipes (two) and connecting

cable with facing tape tightly.In case of leftward

piping and rear-leftward piping, bind the

auxiliary pipes (two) only with facing tape.

Slit (front panel)

Indoor unit

Slit (rear panel)

Auxiliary

pipes

Connecting

cable

Fig. 8-4-13

Installation

plate

<Left-hand connection with piping>

• Carefully arrange pipes so that any pipe does

not stick out of the rear plate of the indoor unit.

Bend the connecting pipe so that it is laid within 43

mm above the wall surface. If the connecting pipe is

laid exceeding 43 mm above the wall surface, the

indoor unit may unstably be set on the wall. When

bending the connecting pipe, make sure to use spring

bender so as not to crush the pipe.

• Carefully connect the auxiliary pipes and

connecting pipes to each other and cut off the

insulating tape wound on the connecting pipe

to avoid double-taping at the joint, moreover,

seal the joint with the vinyl tape, etc.

Bend the connection pipe within a radius of 30

mm.

• Since dewing results in a machine trouble,

make sure to insulate both the connecting

pipes. (Use polyethylene foam as insulating

material.)

• When bending a pipe, carefully do it not to

crush it.

– 26 –

8-4-5. Indoor Unit Installation

8-4-6. Drainage

(1) Pass the pipe through the hole in the wall, and

hook the indoor unit on the installation plate at the

upper hooks.

(1) Run the drain hose sloping downwards.

NOTE :

• Hole should be made at a slight downward slant to

the outdoor side.

(2) Swing the indoor unit to right and left to confirm

that it is firmly hooked up on the installation plate.

Do not rise the drain hose.

Do not form the drain hose

into the wared shape.

(3) While pressing the indoor unit onto the wall by the

lower part, hook it up on the installation plate by

the lower part. Pull the indoor unit toward you by

the lower part to confirm that it is firmly hooked up

on the installation plate.

50 mm

or more

Do not put the

Do not put the drain

hose end in the

drainage ditch.

drain hose end

(1)

into water.

Hook here

Fig. 8-4-17

1 Installation

plate

(2) Put water in the drain pan and make sure that the

water is drained outdoors.

(2)

Push

Hook

(3) When connecting extension drain hose, insulate

the connecting part of extension drain hose with

Fig. 8-4-15

shield pipe.

• For detaching the indoor unit from the installation

plate pull the indoor unit toward you while pushing

its bottom up by the specified parts.

Shield pipe

Drain hose Inside the room

Extension drain hose

Fig. 8-4-18

CAUTION

Arrange the drain pipe for proper drainage from

the unit.

Push

Improper drainage can result in damage to

property.

Fig. 8-4-16

This air conditioner has the structure designed to drain

water collected from dew, which forms on the back of

the indoor unit, to the drain pan.

Therefore, do not store the power cord and other parts

at a height above the drain guide.

Wall

Drain guide

Space for pipes

Fig. 8-4-19

– 27 –

8-5. Outdoor Unit

CAUTION

t Installation place

Installation in the following places may result in

trouble. Do not install the unit in such places.

• A place which provides the spaces around the

outdoor unit as shown in the diagram in page 20.

• A place full of machine oil.

• A saline place such as coast.

• A place full of sulfide gas.

• A place which can bear the weight of the outdoor

unit and does not allow an increase in noise level

and vibration.

• A place where the operation noise and discharged

air do not disturb your neighbors.

• A place where high-frequency waves are likely

to be generated as from radio equipment,

welders, and medical equipment.

• A place which is not exposed to a strong wind.

• A place free of a leakage of combustible gases.

• A place which does not block a passage.

• When the outdoor unit is to be installed in an

elevated position, be sure to secure its feet.

• An allowable length of the connecting pipe is up to

10 m.

• An allowable head level is up to 5 m.

• A place where the drain water does not raise any

problem.

CAUTION

(1) Install the outdoor unit without anything

blodking the air discharging.

(2) When the outdoor unit is installed in a place

exposed always to a strong wind like a coast

or on a high story of a building, secure the

normal fan operation using a duct or a wind

shield.

(3) Specially in windy area, install the unit to

prevent the admission of wind.

Strong

wind

Fig. 8-5-1

– 28 –

8-5-1. Refrigerant Piping Connection

8-5-2. Vacuum Pumping

AIR PURGE

(1) Cut the pipe with a pipe cutter.

Evacuate the air in the connecting pipes and in

the indoor unit using vacuum pump.

Do not use the refrigerant in the outdoor unit.

For details, see the manual of vacuum pump.

Obliquity Roughness

Warp

90˚

Fig. 8-5-2

(1) Connect the charge hose (A) from the manifold

valve to the charge inlet of the gas side packed

valve.

(2) Insert a flare nut into the pipe, and flare the pipe.

A (mm)

Outer

diam.

(2) Connect the charge hose (B) to the port of vacuum

pump.

Imperial Rigid

6.35 mm

9.52 mm

1.3 mm 0.7 mm

1.6 mm 1.0 mm

(3) Open fully the low pressure side handle of the

manifold valve.

Die

Pipe

(4) Operate the vacuum pump.

Fig. 8-5-3

(5) Close the low pressure side handle of manifold

valve after vacuumizing and stop the vacuum

pump.

Align the centers of the connecting pipes and tighten

the flare nut as far as possible with your fingers. Then

tighten the nut with a spanner and torque wrench as

shown in the figure.

Continue vacuumizing more than 15 minutes and

check the pressure gauge indicates –76 cmHg

(–1.013×10⁵Pa).

CAUTION

(6) Open the stems of packed valves A and B all the

way.

• Do not apply excess torque. Otherwise, the

nut may crack depending on the installation

conditions.

(7) Securely tighten the stem cap to each of the

packed valve stems.

Manifold valve

(Unit : N·m)

Additional

tightening torque

19.6 (2.0 kgf·m)

34.3 (3.5 kgf·m)

High pressure

Pressure gage

side handle

Outer diam.

Tightening torque

Low pressure side handle

Charge hose (A)

Outdoor unit

6.35 mm

9.52 mm

15.7 (1.6 kgf·m)

29.4 (3.0 kgf·m)

Charge

hose (B)

Indoor unit

Gas

(ø9.52)

Half union or packed valve

Service port

Flare nut

Externally

threaded

side

Internally

threaded

side

Packed

valve

Liquid

(ø6.35)

Use a wrench

to secure.

Use a torque wrench

to tighten.

Fig. 8-5-4

Fig. 8-5-5

– 29 –

8-5-3. Wiring Connection

CAUTION

(1) Remove the electric parts cover from the outdoor

unit. (1 screw)

• KEEP IMPORTANT 4 POINTS FOR INSTAL-

LATION (PIPING WORK)

(2) Connect the connecting cable to the terminals as

identified with their respective matched numbers

on the terminal block of indoor and outdoor units.

(1) Take away dust and moisture (Inside of the

connecting pipes.)

(Strip the sheath of connecting cable with following

stripping length to and insert into the terminal

block.)

(2) Tight connection (between pipes and unit)

(3) Evacuate the air in the connecting pipes using

VACUUM PUMP.

(3) When connecting the connecting cable to outdoor

unit terminal, make a loop as shown in the

installation diagram of indoor and outdoor unit, to

prevent water coming in the outdoor unit.

(4) Check gas leak (connected points)

(4) Insulate the unused cords (conductors) with water

coming in the outdoor unit. Process them so that

they do not touch any electrical or metal parts.

• Open the valve stem all the way out; so not try to

open it beyond the stopper.

• Securely tighten the valve stem cap with the

wrench or like.

• Valve stem cap tightening torque is as follows;

Gas pipes side (ø9.52) : 29.4 N•m (3.0 kgf•m)

Liquid pipe side (ø6.35) : 16.2 N•m (1.7 kgf•m)

Terminal block

60mm

Terminal

screw

Earth line

10mm

Screw

Earth line

Flare nut

10mm

50mm

Connecting

cable

Cord clamp

Stopper

For a three conductor cable

5mm

Valve body

Valve stem

Fig. 8-5-7

Valve stem cap

CAUTION

Fig. 8-5-6

• Wrong wiring connections may cause some

electrical parts to burn out.

• Be sure to comply with local code on running

the wire from the indoor unit to outdoor unit.

(size of wire and wiring method etc.)

• Every wire must be connected firmly.

NOTE :

• Wipe type : More than H05 RN-F

– 30 –

8-6-3. Auto Restart Setting

8-6. Others

This product is designed so that, after a power failure,

it can restart automatically in the same operating mode

as before the power failure.

8-6-1. Gas Leak Test

Flare nut connections (indoor unit)

Information

The product was shipped with Auto Restart

function in the off position. Turn it on as required.

Electric parts

cover

• Press and hold down theTEMPORARY button for

about 3 seconds. After 3 seconds, the electronic

beeper makes three short beeps to tell you the

Auto Restart has been selected.

Valve stem cap

connection

Flare nut

connections

(Outdoor unit)

• To cancel the Auto Restart, follow the steps

described in the section Auto Restart Function of

the Owner's Manual.

Service cap

connection

Valve stem cap

connection

Fig. 8-6-1

• Check the flare nut connections, valve stem cap

connections and service cap connections for gas

leak with a leak detector or soap water.

8-6-2. Test Operation

To switch the TEST RUN (COOL) mode, press

TEMPORARY button for 10 sec. (The beeper will

make a short beep.)

TEMPORARY

button

TEMPORARY

Fig. 8-6-2

– 31 –

9. TROUBLESHOOTING CHART

TROUBLESHOOTING PROCEDURES :

• Following details of “What to be pre-checked first”, make sure of the basic items.

• When there is no trouble corresponding to above, check in detail the faulty parts following “How to judge

faulty parts by symptoms” later.

9-1-2. Incorrect Cable Connection between

Indoor and Outdoor Units

9-1. What to be Prechecked First

9-1-1. Power Supply Voltage

The indoor unit is connected to the outdoor unit with 3

cables. Make certain that the indoor and outdoor units

have been connected properly, with terminals assigned

the same numbers wired to each other. If the connec-

tors are not connected as specified, the outdoor unit

will not operate normally.

The line voltage must be AC 220/230/240V. If the line

voltage is not within this range, this air conditioner

may not work normally.

– 32 –

9-1-3. Misleading but Good Operations

(Program Controlled Operation)

The microcomputer performs the operations listed in

Table 9-1-1 to control the air conditioner. If a claim is

made on the operation, check whether it corresponds

to the contents in the Table 9-1-1. If it does, it is an

indispensable operation for the control and mainte-

nance of the air conditioner: it is not a failure of the

unit.

Table 9-1-1

No.

Operation of air-conditioner

Description

When the power plug or the power cord The OPERATION lamp flashes, indicating that power is turned

of the indoor unit is inserted, the on. If this happens, push the START/STOP button once to cause

OPERATION lamp on the setting the lamp to stop flashing. A power outage also causes the lamp

indication part flashes.

to flash.

Fan speed remains unchanged in the dry Fan speed is automatically controlled in the dry mode.

mode.

Room temperature is in the range under The compressor will not stop while the compressor on hold timer

which the compressor is turned off, but (3-minutes timer) is actuated.

the compressor will not stop.

The compressor will not switch on or off In the dry mode, the compressor goes on and off at regular

even when the thermo control is operated intervals, independent of the thermo control.

in the dry operation.

Compressor does not work though room Compressor does not work while the compressor restart delay

temperature is in the range of turning the (3-min.) timer is active. The same is true after power is turned

compressor on.

on, as the time is still active.

During automatic operation, the After selection of the cooling and dry operation, the operation

operation mode changes.

mode is selected again when the compressor off mode continues

for 15 min.according to the room temperature. And after selection

of the dry operation, the condition of the room temperature which

is Room temp. ≥Set temp.+1 and which is Room temp.<Set

temp.–4 continues for 15 min., the operation mode is selected

again.

When the power is turned on, the When the auto restart controlling is selected, the operation is

operation starts automatically.

performed automatically in the previous operation mode after

the power supply has been turned on.

– 33 –

9-2-2. Display of Abnormalities and

Judgement of the Abnormal Spots

9-2. Primary Judgement of Trouble

Sources

The indoor unit of this machine observes the opera-

tion condition of the air conditioner and displays the

contents of the self-diagnosis as block displays on

the display panel of the indoor unit.

9-2-1. Role of Indoor Unit Controller

The indoor unit controller receives the operation com-

mands from the remote control and assumes the fol-

lowing functions.

• Measurement of the draft air temperature of the

indoor heat exchanger by using the thermo sen-

sor (TA).

• Louver motor control

• Control of the indoor fan motor operation

• Control of the LED display

• Control of the outdoor unit compressor and the out-

door fan motor.

Table 9-2-1

Block display

OPERATION display flashing (1 Hz)

OPERATION display flashing (5 Hz)

Power failure (when power is ON)

Thermo sensor (TA) short/break

Heat exchanger sensor (TC) short/break

Indoor fan lock, abnormality of indoor fan

Indoor PC board failure

OPERATION, TIMER and FAN-ONLY display

flashing (5 Hz)

• Gas shortage, other refrigerant cycle trouble

• Heat exchanger sensor open/break/short

• Overload relay trouble

(1) Judgement from defective operation or abnormal operation

Table 9-2-2

Symptom

Check

Primary judgement

No reaction on

remote control

operation

Turn off the power once, turn it on

again and try to operate the remote

control again.

Remote control is The indoor part (including the

not possible.

remote control) is defective.

Remote control is OK.

possible.

The outdoor part is defective.

(outdoor fan motor)

The outdoor fan The compressor operates.

does not rotate

The inside part is defective.

The compressor does not operate.

– 34 –

(2) Self-diagnosis with remote control

2) Selecting ordinary mode

With the indoor unit control, self-diagnosis of pro-

tective circuit action can be done by turning the

remote control operation into service mode, oper-

ating the remote control, observing the remote

control indicators and checking whether TIMER

lamp flashes (5 Hz).

Push the all clear button (ACL) on the rear bot-

tom of the wireless remote control with a tip of

pencil for more than 3 seconds. Make sure

the operation mode display, wind volume dis-

play, clock display and setting temperature dis-

play are turned on and “ : ” of the clock display

is flashing.

Note :

• To perform this self-diagnosis, the remote

control with the service code of 43069666 is

required.

1) After completion of servicing, always push the

all clear (ACL) button to return the operation

mode to the normal mode.

2) After completion of servicing by the check

code, turn off the power once and then turn on

the power to reset memorized contents of the

microcomputer to the initial status.

1) Selecting service mode

Push the switch button provided on rear bot-

tom of the wireless remote control with a tip of

pencil for more than 3 seconds. Make sure

the setting temperature

is displayed on

“

”

the display and other display is turned off.

All clear button

Switch for selecting

service mode

ACL

CLOCK

ACL CLOCK

Rear bottom cover

(Rear bottom of remote control)

Fig. 9-2-1

– 35 –

<Self-diagnosis by check codes>

c) At the same time, also make sure the op-

eration lamp is also flashing. This shows

that the protection circuit on the indoor PC

board is working.

1) The self-diagnosis by the check codes is con-

ducted under the block displays of item B-H in

Table 9-2-1.

d) Operate theTEMP.

key and make sure

2) Remote control key operation under the ser-

vice mode is conducted by ON/OFF or TEMP.

The remote control display by each key op-

eration is varied as shown below. Two digit

number is displayed in a hexadecimal num-

ber.

“

”

the remote control display shows

and

flashing of the operation lamp. If the op-

eration lamp is flashing, it shows the pro-

tection circuits for connecting cable is work-

ing or thermal fuse is blown.

e) In the same way, operate the TEMP.

3) The self-diagnosis by the check codes is con-

ducted with procedures shown below.

key so that the display is increased one

by one to continue checks by the self-di-

agnosis as shown in the next table. From

a) Enter the service mode and make sure the

off timer display of the remote control shows

“

”

“

”

up to

check operations of

“

”

protection circuits for each block, and

b) Operate the “ON/OFF” key and make sure

the timer lamp on the display section is

flashing (5 Hz).

“

”

“

”

check operations of the

typical protection circuits.

Table 9-2-3

Indication after operation

Operating key

”

“

ON/OFF

”

➞

”

“

1 is added to data before operation.

(Example)

TEMP.

(Up)

”

➞

1 is subtracted from data before operation.

(Example)

TEMP.

(Down)

”

➞

10 is subtracted from data before operation.

(Example)

“AUTO” LOUVER

“SET” LOUVER

”

➞

Data before operation is directly transferred.

(Example)

– 36 –

Table 9-2-4

Block level

Diagnosis function

Air

Judgment and action

Check

code

Check

code

Conditioner

Block

Symptom

Condition

status

1. Check thermo sensor.

Indoor PC

board

Thermo sensor

short/break.

Continued Indicated when

operation detected abnormal

2. If it is OK, check PC board.

Heat exchanger

sensor short/break. operation detected abnormal

Continued Indicated when

1. Check heat exchanger

sensor.

2. If it is OK, check PC board.

Indoor fan lock,

abnormality of

indoor fan.

All off

Indicated when

detected abnormal

1. Disconnect the power plug

from AC outlet, and pull out

the connector (CN10) for the

motor, then connect the plug

of AC power cord again and

turn the power on.

2. Check the voltage between

pin 1 and 2 of the connector

(CN10).

3. If the output voltage is 35V,

PC board is OK, check

motor.

Abnormality of

other indoor unit PC

board.

All off

Indicated when

detected abnormal

Replace PC board.

1) Gas shortage.

(gas leak)

Indicated when

detected abnormal

Refrigerant

system

1. Check gas quantity.

(check gas leakage)

2) Other refrigerant

cycle trouble.

2. If it is OK, check heat

exchanger sensor.

3) Heat exchanger

sensor off/break/

short.

3. If heat exchenger sensor is

OK. check overload relay and

thermostat for compressor.

4) Overload relay

4. If overload relay is OK, check

refrigerant cycle.

5. If refrigerant cycle is OK,

check PC board.

Contents detected by the check codes “

” to “

” are stored in memory of the microcomputer even if the power

supply is turned off. Therefore, contents of operations in the past are all displayed.

– 37 –

9-3. Troubleshooting Flowcharts

9-3-1. Power can not be Turned on (No Operation at All)

(1) Is the supply voltage normal?

(2) Is the connection to the AC output OK.?

Operation

Check Items

Main cause

Shut off the power supply

from AC outlet once and

turn it on after 5 seconds.

Countermeasure

Symptom

Does the OPERATION

lamp flash?

YES

Does the power turn

on by pushing the

[START/STOP] button

of the remote control?

Does the transmission

indicator of remote

control flash normally and

transmit certainly?

Remote control

is defective.

YES

(No problem)

Replace the

remote control.

Parts (R21, R109, SG01,

C15, C01, DB01, C02,

IC01, T01) are defective.

YES

Does the fuse

(F01) blow?

Wrong wiring of

AC cord or connecting

cable is defective.

Does the thermal

fuse blow?

(Under PF. Terminal)

Replace the

thermal fuse set.

Check connection.

Is the indication voltage

(DC12V or 5V) of main

PC board correct?

YES

Replace the main

PC board.

PC board

is defective.

Is the voltage

across C02 measured

DC310V~340V?

Refer to the paragraph

"Pre-check", or defective circuit

before power PC board block.

YES

Shut off the power

Is the secondary

voltage of SW trans-

former (T01) measured

DC35V, DC12V,

Is the secondary

SW transformer

(T01) or IC (IC01)

for power supply

is defective.

supply once, and turn

it on again after dis-

connecting the motor

voltage of SW

transformer measured

DC35V, DC12V,

and DC7V?

Replace the main

PC board.

connector CN10

and DC7V ?

YES

Motor is defective.

Be sure to disconnect the motor connector CN10 after shut off the power supply, or it will be a cause of

damage of the motor.

– 38 –

9-3-2. Power can not be Turned on after Replacing Indoor PC Board

Connect the AC

Power supply

Return the wiring of the

power relay is returned to

the normal procedure.

Is it wired as shown

in Figure below?

Does the OPERATION

lamp flash?

YES

To the paragraph of

“No Power turns on”.

Black

White

Blue

Brown

C02

RY01

Indoor

terminal

block

Power

terminal

block

PC board

RY02

T02

9-3-3. Outdoor Unit does not Operate

Shut off the power supply

from AC outlet once and

turn it on after 5 seconds.

Does the OPERATION lamp flash?

See "Power can not be turned on".

YES

Does the power turn on by

pushing the [START/STOP] button

of the remote control?

YES

Is AC220/230/240V

Replace the

PC board.

Relays (RY01, RY02)

or IC31 or IC30 is failure.

supplied between terminal block

1 - 2 ?

YES

Is cable connection

Correct cabling between

indoor and outdoor units.

between indoor and outdoor

units correct?

YES

Check items as following procedure

in 9-3-4, 9-3-5, 9-3-6.

– 39 –

9-3-4. Only Compressor does not Operate

Shut off the power supply

from AC outlet once and

turn it on after 5 seconds.

Does the OPERATION lamp flash?

See "Power can not be turned on".

YES

Does the power turn on by

pushing the [START/STOP] button

of the remote control?

YES

Is the voltage across the indoor terminal

( 1 - 2 ) 220/230/240 VAC?

Replace the

PC board.

Relays (RY01, RY02)

or IC31 or IC30 is failure.

YES

Is cable connection between indoor

and outdoor units correct?

Correct cabling between indoor

and outdoor units.

YES

Is the voltage across the outdoor terminal

( 1 - 2 ) 220/230/240 VAC?

Cables between indoor and

outdoor units are defective.

YES

Re-wire or replace the defective cords.

Compressor is defective.

Are all the cords for compressor normal?

YES

Is the compressor motor winding normal?

(Check the winding resistor.)

YES

Capacitor is defective.

Overload relay is defective.

Compressor is defective.

Is the capacitor for compressor normal?

YES

Is the overload relay normal?

YES

Does the compressor start?

YES

Compressor starts but

it stops after a while?

YES

Is the gas quantity normal?

(Check the pressure)

Gas shortage (Gas leakage)

YES

Compressor is defective

– 40 –

9-3-5. Only Outdoor Fan does not Operate

Shut off the power supply

from AC outlet once and

turn it on after 5 seconds.

Does the OPERATION lamp flash?

See "Power can not be turned on".

YES

Does the power turn on by

pushing the [START/STOP] button

of the remote control?

YES

Is the voltage across the indoor terminal

( 1 - 2 ) 220/230/240 VAC?

Replace the

PC board.

Relays (RY01, RY02)

or IC31 or IC30 is failure.

YES

Is cable connection between indoor

and outdoor units correct?

Correct cabling between indoor

and outdoor units.

YES

Is the voltage across the outdoor terminal

( 1 - 2 ) 220/230/240 VAC?

Cables between indoor and

outdoor units are defective.

YES

Are all the cords for outdoor

fan motor normal?

Correct the wire or

replace the defective cords.

YES

Is the outdoor fan motor winding normal?

(Check the winding resistance)

Outdoor fan motor is defective.

YES

Capacitor for outdoor

fan motor is defective.

Is the capacitor for compressor normal?

YES

Outdoor fan motor is defective.

– 41 –

9-3-6. Only the Indoor Fan does not Operate

< Check procedure >

Shut off the power

supply once.

Turn the power supply.

Does the fan

Replace the PC board.

stop in no operating

status?

Control PC board is defective.

YES

Start the operation

with low fan setting

in cool operation.

Is the voltage

measured DC35V

between 1 (red lead wire, +)

and 2 (black lead wire, –)

of the motor connector

(CN10) ?

Shut off the power supply,

and turn it on after

disconnecting the motor

Does the fan rotate?

YES

connector (CN10) from

the PC board.

YES

Shut off the power supply.

Change the setting of

cooling to high fan.

Repair the

bearing of

the drain fan.

Does the cross

flow fan rotate

normally?

YES

Turn on the power supply.

Is the voltage of

DC35V measured

between 1 (red lead wire, +)

and 2 (black lead wire, –) of

the motor connector

(CN10) ?

Replace the

PC board.

Operation

stops

Does the fan speed

become higher?

YES

Is the rotation signal

YES

(DC+5V-0V) output between 4

(blue lead wire) and 2 (black

lead wire) of the motor connector

(CN10) when rotating the cross

flow fan by hand in no operating

status ? (2 pulses/one turn)

YES

Replace the control

PC board.

Replace the

fan motor.

Normal

Be sure to disconnect the motor connector CN10 after shut off the power supply, or it will be a cause of

damage of the motor.

– 42 –

9-4. How to Check the Remote Control (Including the Indoor PC Board)

There is no beep from

the indoor unit.

Push the START/STOP button. The operation lamp of

the air conditioner main

unit does not light.

Does the transmission

indicator flash?

YES

Short-circuit the metal

terminal at the side of the

battery compartment

(all-clear terminal) with a pencil.

(wait about 10 seconds)

Is there direct

sunlight on the

receptor of the

air conditioner?

YES

Is operation

possible when the

transmitter is moved

nearer to the infrared

signal receiver of the

air conditioner?

Is there any

thyristor

fluorescent light

near by?

Push the START/

STOP button

YES

Battery life

Does the

Is operation

transmission

possible when setting

the temporary switch of the

air conditioner main unit to

"TEST RUN" or

indicator light?

YES

"TEMPORARY AUTO"?

Is there any

YES

beep and

operation?

YES

Can any signal tone

be heard in a transistor

radio when transmitting

within 5cm distance

from the radio?

YES

Remote control

PC Board is failure.

is failure.

Keep the air

conditioner away

from thyristor

Avoid direct

sunlight.

Replace remote

control.

Replace the

batteries

Replace

PC board.

Normal

fluorescent light.

After battery replacement,

Note:

shortcircuit the metal terminal at

the side of the battery compartment

(all-clear terminal) with a pencil.

– 43 –

9-4-1. How to Check the PC Board

(1) Operating precautions

(2) Inspection procedures

1) When a PC board is judged to be defective,

check for disconnection, burning, or discolora-

tion of the copper foil pattern or this PC board.

1) When removing the front panel or the PC

board, be sure to shut off the power supply.

2) The PC board consists of the following 2 parts

2) When removing the PC board, hold the edge

of the PC board and do not apply force to the

parts.

a. Main PC board part:

Power relay, indoor fan motor drive circuit

and control circuit, C.P.U.and peripheral cir-

cuits, buzzer drive circuit and buzzer.

3) When connecting or disconnecting the connec-

tors on the PC board, hold the whole housing.

Do not pull at the lead wire.

b. Infrared rays receive and indication

parts:

Infrared rays receive unit and LED.

– 44 –

(3) Checking procedure

Table 9-4-1

No.

Procedure

Check Point (Symptom)

Causes

Shut off the power supply and

remove the PC board assembly

from the electronic parts base.

Remove the connecting cable from

the terminal block.

1. Is the fuse blown?

1. * Application of shock voltage.

* Overload by short-circuit of the

parts.

Remove the connector for the

motor, and turn the power on.

Voltage check

1. Between TP1 and TP2

(220/230/240V AC)

2. Between TP2 and pin 1 of CN04 2. Fuse is defective.

(220/230/240V AC)

1. * AC power cord is defective.

* Poor contact of the terminal plate.

* Miss wiring of the power relay.

If the OPERATION lamp flashes

(0.5 sec. :ON, 0.5 sec. :OFF) when

the power turning on, the checking

points described as 1-5 of right

column are not necessary to

perform.

3. Operation of the thermal fuse.

3. Between TP2 and pin 3 of CN04 4. * Capacitor (C01, C15) is defective.

(220/230/240V AC)

* Line filter (L01) is defective.

* Resistor (R01) is defective.

* Diode (DB01) is defective.

5. IC01, IC02, T01 are defective.

6. IC01, IC02, T01, F03 are defective.

7. IC01, IC02, T01, F02, Q29, IC03

are defective.

4. Between + and - of C02

(310 ~ 340V DC)

5. Between 35V and GND

6. Between 12V and GND

7. Between 5 V and GND

Voltage check

1. Voltage of relay coil. (DC 12V)

Between pin 10 of IC31 and GND

Between pin 11 of IC31 and GND

2. Between No. 1 and 2 of connecting

cable terminal block.

1. Breaking wire of the relay coil,

defective relay driver. (IC31)

2. Poor contact of relay.

Make the operation status by

pushing once the START/STOP

button, except the status of [FAN

ONLY], [ON TIMER].

(220/230/240V AC)

1. All indicators light for 3 sec..

2. Indicators do not indicate normally

after approximate 3 sec..

Start the operation with the system

which the time of the restart delay

timer is shortened.

Defective indicator, or poor

housing assembly. (CN13)

1. Compressor does not operate.

2. OPERATION lamp flashes.

1. The temperature of the indoor heat

exchanger is abnomally lower.

2. Poor contact of the heat exchanger

sensor. (The connector is

disconnected.) (CN01)

3. Heat exchanger sensor, main PC

Make the operation status by pressing

once the START/STOP button.

1. The time of the restart delay timer

is shortened.

2. Cool operation

3. Air volume [AUTO]

4. Make the setting temperature lower

enough than room temperature.

5. Continuous operation.

board are defective.

(Refer to Table 9-4-2 for the judgment

of defective resistance values.)

4. Main PC board is defective.

1. The temperature of the heat

exchanger is abnormally high.

2. The heat exchanger sensor

connector has short-circuit. (CN01)

3. The heat exchanger sensor is

defective.

1. Compressor does not operate.

2. OPERATION lamp flashes.

The status of No. 5 is continued,

and make the following condition.

1. Heat operation

2. Make the setting temperature

higher enough than room

temperature.

(Refer to Table 9-4-2 for the judgment

of defective resistance values.)

4. PC board is defective.

1. Indoor fan motor is defective.

(Protecting operation on the PC

board.)

2. Poor contact of the motor

connector.

1. The voltage of DC 35V is not

measured between the red and

black of the motor terminals.

2. Motor does not rotate.

(The key operation is accepted.)

3. The motor rotates, but it vibrates

too much.

Turn the power on after connecting

the motor connector.

Start the operation with the following

condition.

1. Operation [Cooling]

2. Airflow [High fan]

3. Continuous operation

3. PC board is defective.

– 45 –

9-4-2. PC Board Layout

Top View

Bottom View

– 46 –

Table 9-4-2 Approximate value of the sensor (thermistor) resistance (TA,TC)

Temperature

(= kΩ)

30°C

0°C

10°C

20°C

25°C

Sensor

Themo Sensor

35.8

20.7

12.6

10.0

7.92

9-4-3. How to Reduce the Operation Time of

the Anti-Restart Timer

Wireless remote control

• Attach the diode (1S1555 or equivalent) to the rivet

inside the unit through holes on the rear of the

wireless remote control unit.

• Push the START/STOP button to start operation

with the diode attached.

Timer short diode

Fig. 9-4-1

– 47 –

10. PART REPLACEMENT

10-1. Indoor Unit (RAS-10SK-E, RAS-10SKX)

No.

Part name

Front panel

Procedure

Remarks

1) After stopping the operation of the air conditioner, be

sure to turn off the circuit breaker or disconnect the

power plug from the AC wall socket.

2) Open the screw caps and remove the two screws

fixing the front panel.

3) Close the screw caps as they were.

4) Open the horizontal louver right below by your

finger.

5) Open the lower side of front panel until it touches

the horizontal louver, and remove it from the indoor

unit by turning it.

1) Fix the two screws to secure the front panel.

2) Close the screw caps as they were.

3) Press four places where are the center, right end,

left end and lower portions of the air outlet.

4) Check the gap between the front panel and the main

unit.

If cooling or drying operation is performed without

pressing the center of the air outlet, the surface of

the front panel may be covered with frost and have

a waterdrop.

Electrical part

assembly

1) Perform the process above.

‚

2) Remove the screw securing the shield metal plate.

3) Remove the electrical part cover by pressing the nail

located on upper portion of the electrical part cover.

4) Remove the drain guide.

5) Remove the screw securing to the end plate of the

heat exchanger.

6) Remove the connector (5p) for the fan motor and

the connector (6p) for the louver motor from the

microcomputer assembly.

7) After unhooking the electrical part base by pressing

the fixing nail located on its lower portion, draw the

electrical part base out toward you to remove it from

the main unit.

8) Pull the TC sensor out from the holder of the heat

exchanger.

9) Dress the connecting cable securely as shown in the

right illustration.

(Improper dressing will cause water leakage.)

Drain-pan

assembly

1) Perform the process ‚ above.

2) Remove the drain-pan by pressing the four hooks

downwards.

(Keep it with the drain hose.)

– 48 –

No.

Part name

Procedure

1) Perform the process ‚.

Remarks

Horizontal grille

Note:

„

2) Remove the screw fixing the louver motor, and

remove the louver motor.

The horizontal

grille can not be 3) Remove the shaft of the horizontal grille from the

removed without

removing the

louver motor.

drain-pan.

Heat exchanger 1) Perform the process ƒ.

ꢀ

2) Remove the pipe holder from the rear side of main

unit by removing the screw.

3) Unhook the hooks fixing the left side of the heat

exchanger and remove the screw fixing it, then

remove the right side of the end plate from the rib

fixing the main unit by sliding the heat exchanger

slightly to the right side.

Cross flow fan

†

1) Perform the process ƒ.

2) Loosen the set screw of the cross flow fan.

3) Remove the screw fixing the shaft bearing base.

4) Lift slightly up the left side of the heat exchanger,

and pull the shaft bearing base out left downwards.

When assembling it, fix it with the set screw on the

position where the gap between the rear plate surface

and the left end surface of the cross flow fan is 6 ~

7mm.

Shaft bearing

1) Perform the process † above.

‡

2) Remove the shaft bearing from the shaft bearing base.

• If a part of the shaft bearing is protruded from the

housing, assemble it after pushing its portion into

the correct position in the housing.

Fan motor

1) Perform the process ꢀ above.

2) Perform the process †-2) above.

3) Remove the left and right motor bands.

4) Remove the fan motor after pulling the cross flow

fan out sliding it left and right.

– 49 –

10-2. Microcomputer (RAS-10SK-E, RAS-10SKX)

No.

Part name

Procedure

Remarks

Common

procedure

1) Turn the power supply off to stop the operation of

Replace the thermal fuse, terminal

air-conditioner, and disconnect the power cord from block, power cord, microcomputer

the AC supply.

ass’y and the power supply PC

board ass’y.

2) Remove the front panel.

• Remove the two fixing screws. (φ4 x 14

3) Remove the electrical part base.

)

Thermal fuse

replacement

1) Perform the process above.

‚

2) Remove terminal cover (Up), (Down).

3) Disconnect the terminal blocks connected with the

connecting cable, and the power cord from base E-

parts by removing the screws.

4) Remove the thermal fuse (77°C) from base E-parts.

– 50 –

10-3. Outdoor Unit (RAS-10SA-E, RAS-10SAX)

No.

Part name

Procedure

Remarks

Common

procedure

1) Stop the operation of air-conditioner, and disconnect

the power cord from the AC supply.

2) Remove E-parts cover.

(1- ST1T ø4 x 10

)

3) Remove the cord clamp (2- ST2T ø4 x 12 ) and

remove the connecting cable.

4) Remove the front cabinet. (7- ST1T ø4 x 10 with

nylon washer)

• Pull the front lower portion toward you, and remove

it pulling out upward.

1) Remove the fixing screw securing the capacitor

band.

Capacitor for

compressor

Refer to [Electrical parts list and

location] in page 55.

‚

(1- ST2T ø4 x 8

)

2) Remove the cable connected to the terminal.

Capacitor for fan 1) Remove the fixing screw.

Same as above.

„

motor

(1- ST2T ø4 x 8

)

2) Remove the cable connected to the terminal.

Overload relay

1) Perform the process above.

2) Remove terminal cover of compressor.

3) Remove OL holder and pull OL relay up.

4) Remove Fustons of leads.

– 51 –

11. CAUTIONS ON REPLACEMENT OF PC BOARD ASSEMBLY

1. Set the switch (SW03) provided on the PC board as follows.

OFF

2. Don?t wind the black lead wire around the current trans. (CT. T02)

Black

White

Blue

Brown

C02

RY01

Indoor

terminal

block

Power

terminal

block

PC board

RY02

T02

– 52 –

12. EXPLODED VIEWS AND PARTS LIST

12-1. Indoor Unit (1)

406

404

403

401

407

408

402

405

401

Location

No.

Part

No.

Location

Part

No.

Description

No.

401

402

403

404

43T60002 Base, Terminal

3P, AC 300V, 20A

405

43T69007 PC Board, WRS-LED

MCC-635

43T69004 Sensor, Heat Exchanger

406

407

43T69008 PC Board MCC-713

43T61001 Base, E-Parts

ABS, Black, UL94-5V

43T62006 Base, Shield

SGCC-Z08-LUB

10kΩ, 25°C

43T69005 Sensor, Thermostat

10kΩ, 25°C

408

43T60004 Fuse, Temperature 77°C

– 53 –

Indoor Unit (2)

233

230

231

228

229

222

221

215

216

217

211

214

210

232

201

202

223

226

227

236

225

241

220

218

219

206

224

235

207

212

213

239

209

208

234

237

205

240

203

204

242

238

Location

No.

Part

No.

Location

No.

Part

No.

Description

201

202

203

204

205

206

207

208

209

210

43T00002 Front Panel Assembly

43T00003 Suction Grille

43T80001 Air Filter (L)

43T80002 Air Filter (R)

43T80003 Frame Filter

43T07004 Screw Cap (L)

43T07003 Screw Cap (R)

43T08007 LED Panel (10SK-E)

43T08005 LED Panel (10SKX)

43T19004 Accepted Signal Filter

43T09003 Horizontal Louver Assembly

for Service

43T09004 Louver Assembly

43T70001 Drain Hose Assembly

43T21003 Motor Stepping

43T07001 Bushing

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

43T49005 Plate of EVA-SEAL

43T49006 Holder for Plate of EVA-SEAL

43T49004 Rubber of Sound Insulation

43T79002 Drain Guide

43T39002 Motor Band (Left)

43T39001 Motor Band (Right)

43T21005 Fan Motor

43T20007 Fan, Cross Flow

43T22002 Bearing

43T39003 Base, Bearing

43T03001 Rear Plate

43T07002 Pipe Holder

211

212

213

214

215

43T82001 Installation Plate

43T85004 Owner’s Manual (10SK-E)

43T85006 Owner’s Manual (10SKX)

43T11001 Pipe Shield

43T69009 Remote Control

43T63002 Holder, Remote Control

43T62008 Cover, E-Parts

43T62002 Terminal Cover (Up)

43T62005 Terminal Cover (Down)

43T62003 Cord Clamp

43T44003 Refrigerantion Cycle

Assembly

216

217

218

219

220

43T47006 Pipe, Delivery

43T47005 Pipe, Suction

43T49007 Pipe, Shield

43T19003 Holder, Sensor

43T49003 Spring

43T62004 Shield Cover

– 54 –

12-2. Outdoor Unit

8, 9

10, 11

7 : CAPILLARY TUBE

26 : DRYER

Location

No.

Part

No.

Location

No.

Part

No.

Description

43T19001 Guard Fan

43T19005 Handle

43T20001 Fan, Propeller

43005037 Front Cabinet

43T43004 Condenser

43T49001 Rubber-Cushion

43T19002 Stopper, Guard

43T63001 Holder, OL-Relay

43054408 Relay, Over-Load

J-MRA 99285-9201

43062193 Cover, E-Parts

43005038 Back Cabinet

43T47008 Capillary-Tube 1.5 DIA

43T46001 Packed Valve, 9.52

43T47002 Bonnet, 9.52 DIA

43T46002 Packed Valve, 6.35

43T47003 Bonnet, 6.35 DIA

43T21001 Fan-Motor UE6-21SJ5P

43T47001 Flange, Nut

43T41402 Compressor, PH102T1-4C

43055483 Capacitor Plastic, Comp

25µF 400V

43T55001 MF Capacitor 1.5µF, 500V

43T60006 Base,Terminal , 3P

43045073 Dryer

– 55 –

Microsoft Spc210sf User Manual
Oricom Secure 310 User Manual
Philips Nb Scb2050 User Manual
Samsung Aqv18j User Manual
Samsung Tipo Ventana Aw0700b User Manual
Sanyo 26xw72r User Manual
Soleus Air Gm Wac 10ese C User Manual
Toshiba Ras B10gkvp E User Manual
Xerox Workcentre M24 User Manual
York Y32 User Manual