KS-1018
Kachinko System (clapperboard)
Operating Manual
Kachinko System
The audio beep may be recorded using a mi-
crophone, or output at microphone or line level
into a mixer.
The beep may be manually triggered, or trig-
gered automatically, with a visual countdown.
Batteries
Slide the catch to
open the battery
cover and insert the
batteries
3
Kachinko System
The KS-1018 uses four ‘AA’ batteries. The bat-
tery cover is located on the rear of the unit.
Slide the catch away from the center in order
to unlock the hinged door. Insert the batteries
as marked on the inside of the battery com-
partment.
The normal precautions apply when inserting
or replacing batteries into the KS-1018:
•
•
•
Take care that the batteries are inserted
correctly as shown in the battery compart-
ment, with the polarity correct.
Never mix batteries of different types, or
discarded (or partially-discharged) and
new (or freshly-charged) batteries.
Always follow the battery manufacturer’s
instructions for charging rechargeable bat-
teries. Never attempt to recharge batteries
which are not designed for this purpose.
Close and latch the battery compartment.
4
Kachinko System
A threaded socket on the bottom of the KS-
1018 allows it to be used with any standard
tripod and shoe system, if desired. Otherwise,
standard rubber feet keep the unit steady.
Open the four shutters at the front of the unit
before using it, to expose the “clapperboard”
front light:
Note the ONE SHOT button
on the top of the unit.
Front light
Front light
Countdown lights
5
Kachinko System
Controls
The controls for the unit are located on the
Power indicator; lights
when the POWER
switch is in either of
the ON positions
POWER switch: three
settings: ON is on, with
no buzzer, OFF turns
the unit off, and ON
(BUZZ ON) uses the
built-in buzzer
KS-1018
VIDEO KACHINKO
ON
OFF
ON (BUZZ ON)
MODE switch: two
settings: AUTO
POWER
MODE
enables the top ONE
SHOT button, MANU
uses the POWER
AUTO
MANU
switch to produce the
clapperboard effect
MIC
LEVEL
LINE
TONE OUT
LEVEL switch: two
settings: MIC sets a
–50dBm mic level
output from the TONE
OUT XLR jack, LINE sets
a 0dBm line level
TONE OUT: balanced transformer
XLR audio tone output
6
Kachinko System
right (as you look from the front):
Operation
Locate the unit where the front light is clearly
visible by the camera.
•
•
•
Make any necessary connections from the
TONE OUT to the camera, if you are not us-
ing the camera’s microphone.
If you are recording the signal with the
camera microphone, set the POWER switch
to ON (BUZZ), otherwise set it to ON.
Set the camera iris setting to manual. An
automatic setting can overcompensate for
the KS-1018’s lighting, and make it impos-
sible to see the “clapperboard” effect on
the target monitor.
•
Make the image of the front light as large
as possible by putting the camera close in
front of the KS-1018. The focus of the cam-
era is not important in this case.
Set the MODE switch to AUTO. The main light
lights, and the beep sounds (or the signal is
output through the jacks). The three red LEDs
7
count down and when they reach the end of
the sequence, the front light lights, and the
beep sounds.
This sequence is repeated as long as the unit
is on.
Or, if you set the MODE switch to MANU (man-
ual), the top ONE SHOT button can be used
to light the front light and sound the beeper
together.
Read the KS-1017 manual for further details
of how to measure the delay between the video
and audio signals when they are received.
Physical specifications
125 x 90 x 60 (mm)
Dimensions (w x h x d)
4.9 x 3.5 x 2.4 (in)
Weight
1kg (2.2lb)
Sigma Systems Engineering Co. Ltd.
3-5-2 Okubo
Shinjuku-ku
Tokyo 169-0072
JAPAN
Tel: +81 3 3204 2611
Fax: +81 3 3204 2250
e-mail: [email protected]
|