Siemens Gigaset Sx255 User Manual

Be inspired

Contents

ISDN glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Safety precautions

Use only the power unit supplied, as indicated on the underside of the base

station.

The operation of medical appliances may be affected. Be aware of the techni-

cal conditions within the particular environment (e.g. doctor's practice).

Do not install the base in bathrooms or shower rooms. The handset and base

are not watertight.

Do not use the phone in environments subject to explosion hazard (e .g. auto

paint shops).

If you give your Gigaset to someone else, make sure you also give them the

operating manual.

Dispose of the batteries and phone in accordance with environmental regula-

tions.

Getting started

Pack contents

1 base

1 power supply cord with power unit

1 ISDN connection cable

1 USB cable

1 wall holder

Operating instructions

Notes on installation

The installation location must have a 220/230V~ mains outlet and an ISDN tele-

phone connection.

For optimum radio reception, you should install the base at a central point wherever

possible.

The installation location should not be in the immediate vicinity of other equipment,

e. g. hi-fi, television, office or microwave equipment, in order to prevent mutual

interference. Minimum distance (including to base power unit): 1.5 metres.

In case of picture and sound interference on satellite reception equipment, please

contact your retailer to have your satellite reception system checked for a lack of

screening.

Avoid direct contact with sources of heat (e .g. radiators).

Do not expose the base to direct sunlight.

The base can also be wall mounted, using the wall holder included in the pack.

If you are not using wall mounting, install the base on a level, non-slip surface. The

feet of the device do not normally leave any marks on the installation surface. How-

ever, in view of the variety of paints and polishes available, it cannot be ruled out,

that contact may cause marks on the installation surface.

The range between the base and the handsets is up to 300 m in the open air. Inside

buildings, ranges of up to 50 m can be achieved.

Use as desktop unit

Your telephone can be used as a space-saving desktop unit. Before connecting the base,

please read the notes on installation (page 3, page 4).

Getting started

Mounting the base as a wall unit

Before mounting the base, please read the notes on installation (page 3, page 4).

1. Drill two holes (∅ 5 mm) 80 mm apart next to one an-

other in the wall.

2. Use appropriate rawlplugs.

3. Screw in two round screws (∅ 4 mm).

4. Before attaching the wall holder and tightening the

screws, place the connection cable through the hold-

er from the back to the front. Ensure that the connec-

tion cable lies freely in the back recess.

5. Now plug the connection cable into the base (see

Connecting the base).

6. Using slight vertical pressure from the top centre,

press the base onto the retaining catches on the wall

holder.

Getting started

Connecting the base

Front of unit

Schematic illustration

1. -S jack: Insert ISDN connection cable until connector clicks into place.

2. Insert ISDN connection cable into ISDN connection until connector clicks into place.

3. For NTBA with self-mounting, plug in the cable between the NTBA and the TAE (old

telephone outlet) or Mini-Western connector until both connectors click into place.

jack: Plug in the power supply cord, until the connector clicks into place and plug

into the mains outlet.

Use only the power unit supplied, as indicated on the underside of the

base station.

Power failure:

Your base and the handsets registered on it, as well as wire-based termi-

nals cannot operate in case of power failure. However, all the settings

and stored information (messages, phonebook entries etc.) are retained

indefinitely.

Getting started

Connecting auxiliary equipment

You can connect the following auxiliary equipment to your base:

up to eight wireless devices (handsets see page 9, Gigaset data modules see

page 30, Gigaset Repeater see page 30)

up to two analogue, wire-based devices (e.g. telephone, answering machine, fax

machine, entrance telephone – see page 26)

a PC via USB port (USB V1.1 – see page 30)

Connection in Germany

Connection for the wire-

based terminal with inter-

nal number 22

Connection for the wire-

based terminal with inter-

nal number 21

USB

ISDN

The connections are provided for the

use of analogue terminals using TAE

connectors.

Schematic illustration

Connection in other countries

Connection for the wire-

based terminal with inter-

nal number 22

Connection for the wire-

based terminal with inter-

nal number 21

USB

ISDN

The connections are provided for the

use of standard terminals using Mini-

Western connectors.

Schematic illustration

Getting started

Setting and operating the base

Preparing the base for use and making settings

In order to be able to use your base, certain settings are required, e. g. the ISDN phone

number (MSN). To do this, you need a handset or a PC. More details can be found in the

operating instructions for your handset or your PC software.

If you have an S1 or SL1 added-feature handset, a Getting started wizard is available to

assist you in making the settings. More details can be found in the operating instruc-

tions for your added-feature handset.

Operating the base from a handset

Operating instructions for the S1, SL1, C1 and C2 handsets are enclosed.

The current version of the operating instructions is available on the Internet at

www.my-siemens.com/gigaset.

Below, examples of operating the base from an S1 or SL1 handset and a C1 or C2 hand-

set are presented for "Assigning an MSN a ringer melody".

Operating the base from an S1 or SL1 handset

The central operator control on the S1 and SL1 handsets is a control key p, which has

four black direction arrows with the associated symbols. Pressing the various icons (up,

down, right, or left) opens a different function. The side you have to press is shown by

a black triangle in the operating instructions, e.g.: v key for right = open menu.

Example: "Assigning an MSN a ringer melody"

Open the menu.

Select the menu item and confirm.

s Set base

s Settings

~ ^OK

Select the menu item and confirm.

Enter system PIN if required (page 10).

Select the menu item and confirm.

Select MSN, e.g. MSN1: Anna.

Open the submenu.

s ISDN settings

s Set up MSN

Select melody and confirm, e.g. Ringer Melody: 5

(‰ = activated).

r Ringer Melody: 5

Operating the base from a C1 or C2 handset

The C1 and C2 handsets each have a rocker key, which has two functions.

On the Gigaset C1, the upper half of the rocker key has the function of the Talk key c,

the lower half the Phonebook key h.

On the Gigaset C2, the upper half of the rocker key has the function of the Talk key c,

the lower half the Handsfree key d.

Getting started

Example: "Assigning an MSN a ringer melody"

Open the menu.

Select the menu item and confirm.

Enter system PIN if required (page 10).

Select the menu item and confirm.

Select MSN, e.g. MSN1: Anna.

Open the submenu.

s Set base

s Settings

~ OK

s ISDN settings

s Set up MSN

Select melody and confirm, e.g. Ringer Melody: 5

(‰ = set).

s Ringer Melody: 5

Registering handsets

You can register a maximum of eight wireless devices on your base (including

Gigaset data modules (page 30) and Gigaset Repeater (page 30)). The internal num-

bers 11-18 are set aside for this purpose. Wire-based analogue devices do not have to

be registered (page 26).

If the internal numbers Int.11 to Int.18 on your telephone have already been assigned,

please de-register another handset you no longer require before registering a new one

(see handset operating instructions).

If necessary, keep the handset operating instructions to hand with their description of

the registration process.

You must initiate handset registration on the handset and on the base.

1. On the base

Press the registration/paging key on the base for about 3 seconds. This starts the regis-

tration. The base is ready for registering for 30 seconds.

Press the lit Registration/Paging key

2. On the handset (within 30 sec.)

If the handset cancels base paging, e. g. because the registration time has

been exceeded, repeat the process.

Getting started

Manually registering a Gigaset S1 / SL1 handset

Open the menu.

s Settings

s Register H/Set

s Base 1

Select the menu item and confirm.

Select base (1–4) and confirm, e. g. Base 1.

Enter the system PIN of the base (factory setting:

0000) and confirm. In the display are Regstr.Proce-

dure and the name of the base, e. g. Base 1.

Once the handset has located the base, the list of

free internal numbers is shown in the display.

Press lit Register key on the base (page 9), key

flashes. The base is only ready for registering while

the key is flashing.

Select internal number and confirm, e. g. Int.11 .

s Int.11

After registration the handset reverts to idle status. The handset's internal number is

shown in the display.

Manually registering a Gigaset C1 / C2 handset

Open the menu.

Select the menu item and confirm.

Select base (1–4) and confirm, e. g. Base 1.

s Handset Settings

s Register Handset OK

s Base 1

~ OK

Enter the system PIN of the base (factory setting:

0000) and confirm. In the display are Registering

and the name of the base, e. g. Base 1.

Once the handset has located the base, the list of

free internal numbers is shown in the display.

Press lit Register key on the base (page 9), key

flashes. The base is only ready for registering while

the key is flashing.

Select internal number and confirm, e. g. Int.11 .

s Int.11

After registration the handset reverts to idle status. The handset's internal number is

shown in the display.

Getting started

Registering a Gigaset 4000 Comfort/Micro handset

Hold down, to turn on the handset.

either ...

Confirm the prompt.

or ...

Select the menu item and confirm.

G Settings

G Register H/Set

G Base 1

Select base (1–4) and confirm, e. g. Base 1.

... then

Enter the system PIN of the base (factory setting:

0000) and confirm.

~ OK

Press lit Register key on the base (page 9), key

flashes. The base is only ready for registering while

the key is flashing.

Select internal number and confirm, e. g. Int.11 . The

successful registration is confirmed on the display.

s Int.11

Registering a Gigaset 4000 Classic handset

You can register a maximum of four Gigaset 4000 Classic handsets.

Press lit Register key on the base (page 9), key

flashes. The base is only ready for registering while

the key is flashing.

Hold down, to turn on the handset.

Confirm the prompt.

YES

Enter the system PIN of the base (factory setting:

0000) and confirm.

~ OK

The handset is registered.

The next unassigned internal number between Int.11 and Int.18 is automatically

assigned to the handset as it is registered.

Getting started

Registering a Gigaset 3000 Comfort/Micro handset

Hold down, to turn on the handset.

−

either ...

Confirm the prompt.

or ...

Open the menu.

Select the menu item and confirm.

Select the base (1-4) and open the sub-menu.

Select the menu item and confirm.

s Stations

s Station 1

s Registration

... then

Enter the system PIN of the base (factory setting:

0000) and confirm.

~ OK

Press lit Register key on the base (page 9), key

flashes. The base is only ready for registering while

the key is flashing.

Select internal number and confirm, e. g. Int.11 . The

successful registration is confirmed on the display.

s Int.11

The next unassigned internal number between Int.11 and Int.18 is automatically

assigned to the handset as it is registered.

Registering a Gigaset 3000 Classic handset

Hold down, to turn on the handset.

−

Press in turn.

Enter the number of the base (normally 1) and con-

firm. The Standby symbol C flashes and then lights

up constantly when the connection to the base has

been established.

~ OK

Enter the system PIN of the base (factory setting:

0000) and confirm.

~ OK

Press lit Register key on the base (page 9), key

flashes. The base is only ready for registering while

the key is flashing.

Select internal number and confirm, e. g. Int.11 . The

Standby symbol is extinguished after successful reg-

istration.

s Int.11

Getting started

Registering a Gigaset 2000 C handset

Press to turn on the handset.

Open the menu.

Select the menu item and confirm.

Select base (1-4) and confirm.

Open the submenu.

s Settings

s Registration

s Station 1

Select the menu item and confirm.

s Registration

~ OK

Enter the system PIN of the base (factory setting:

0000) and confirm.

Press lit Register key on the base (page 9), key

flashes. The base is only ready for registering while

the key is flashing.

Select internal number and confirm, e. g. Int.11 . The

successful registration is confirmed on the display.

s Int.11

Registering a Gigaset 2000S / Gigaset 1000 C/S handset

For the registration procedure described below:

You can register a maximum of four other handsets (e. g. Gigaset 2000S, GAP handsets)

or wireless devices (e. g. Gigaset 1000 TAE, STA). Register these devices first.

Registering a Gigaset 2000S handset

Press h (off).

Simultaneously press the number of the base station

and ^h(on).

Enter system code.

Press lit Register key on the base (page 9), key

flashes. The base is only ready for registering while

the key is flashing.

The lowest free internal number is assigned. It is not possible to select a free internal

number.

Registering a Gigaset 1000 C/S handset

For the registration procedures, please refer to the corresponding operating instruc-

tions.

Getting started

De-registering handsets

Handsets are de-registered using a handset (see handset operating instructions). Exam-

ple:

Open the menu.

Select the menu item and confirm.

s Base Settings

s Settings

~ OK

Select the menu item and confirm.

Enter system PIN if required.

Select the menu item and confirm.

s Setup user

s De-reg. device

s Int.16

Select the handset that you wish to de-register and

confirm, e.g. Int.16.

The other registered devices retain their previous internal numbers.

Locating a handset (paging)

If you have mislaid your handset you can page it with the help of the base. The Regis-

tration/Paging key is located on the top of the base (page 9).

Paging:

Press the Registration/Paging key on the base for 1 second. All handsets will ring

together ("Paging").

End paging:

Press the Registration/Paging key on the base for a maximum of 1 second or the Talk key

on the handset.

Supported handsets

The SX205isdn and SX255isdn bases support the S1, SL1, C1 and C2 handsets. Operat-

ing instructions for these handsets are enclosed. The current version of the operating

instructions is available on the Internet at www.my-siemens.com/gigaset or contact the

hotline (page 34).

Features

When used in conjunction with a Gigaset handset, your SX205isdn or SX255isdn base

offers you a variety of features. Depending on the handset used, you have access to a

particular range of these features. The table below tells you which features can be used

with which handsets. The table is based on the table of contents of the handset operat-

ing instructions.

Feature

SL1

Making the handset ready for service

Operating the handset – Menu system

Control key

Yes

Preparing base for use – Getting started wizard

Making calls

Yes

Handsfree

Reserving a line

Defining the send MSN for the next call

Callback when busy (CCBS) / when the call is not

answered (CCNR)

Yes

Identify caller

Yes

Functions during a call

Muting the handset

Yes

Making a call to several users

External / Internal enquiry

Toggling

Conference call

Forwarding an incoming call – CD (Call Deflection)

Working with external call waiting – CW (Call Waiting)

Using the phonebook and other lists

Yes Yes

Yes

Phonebook and speed dial list

Yes

Dialling with the phonebook/speed dial list

Copying and changing a phonebook entry

Marking a phonebook entry as VIP

Adding a displayed telephone number to the phone-

book

Yes

Sending a single entry or complete list to a handset

Saving an anniversary for a phone number

Voice dialling

Yes

Supported handsets

Feature

Yes

SL1

Yes

Announcing the caller's name

email directory

Last number redial list

Caller lists

Yes

Making cost-effective calls

Linking a call-by-call number with a phone number

Displaying the call duration

Displaying call charges

Setting up the charge calculation

SMS (text messages)

Yes

Sending text messages and outgoing message list

Saving text messages

Yes

Inserting pre-written text or an email address in an

SMS

Sending a text message to an email address

Receiving text messages and incoming message list

Replying to or forwarding text messages

Calling back the text message sender

Yes

Copying a phone number from SMS text into the

phonebook

Adding the telephone number of a text message to the Yes

phonebook

Yes

Using new ringer tones and logos for the handset

Yes

Direct operation of answering machine (on Gigaset 255isdn)

Recording memos

Two-way recording

Yes

Returning a call during playback

Playing a message to another caller

Setting the playback speed

Yes

Marking an old message or memo as "new"

Adding a number to the phonebook

Setting the answering machine (on Gigaset 255isdn)

Deactivating/activating spoken date and time

Setting the recording time and recording quality

Locking the answering machine, defining AM PIN

Setting the time control

Yes

Activating/deactivating automatic listen in on the hand- Yes

set

Yes

Activating/deactivating listen in

Activating/deactivating automatic call pick up

Activating/deactivating automatic notification via text

message

Yes

Supported handsets

SL1 C2 C1

Yes Yes No

Feature

Yes

Using several handsets

Using a handset as a room monitor

Setting walkie talkie mode

Date and time

Yes

Setting the date and time

Setting the alarm clock

Setting an appointment

Displaying unaccepted appointments, anniversaries

Night service

Yes

Security settings

Changing the system PIN

Defining authorisation

Emergency numbers

Yes

System settings

Changing the name for an internal user

Assigning a phone number (MSN)

Assigning a receive MSN

Assigning a send MSN

Setting up a send MSN list for the next call

Setting up a busy signal when the MSN is being used

(Busy on Busy)

Yes

Assigning an MSN a ringer melody

Setting up rejecting for the entire MSN group

Diverting calls

Yes

Forwarding internal calls

Diverting external calls – CF (Call Forwarding)

Pre-assigning the call deflection destination – CD (Call

Deflection)

Yes

Setting up automatic call divert when a handset is not

available

Yes

Setting up an internal group call group

Setting up ring delay

Activating/deactivating call waiting – CW

Setting an external/internal enquiry call

Setting up the waiting melody

Activate/deactivate call before data

Changing the long distance prefix

Checking the software version

Yes

Individual handset settings

Change display language

Yes

Activate/deactivate automatic call acceptance

Changing the name of the base

Adjusting the loudspeaker volume

Yes

Supported handsets

Feature

Yes

SL1

Yes

Ringer echo

Changing the ringer tone

Yes

Activating/deactivating the ringer

Activating/deactivating the alert tone

Vibration alarm

Activating/deactivating advisory tones

Restoring the handset factory settings

Operating with other devices

Defining the device type

Yes

Activating/deactivating Repeater mode

Operating when connected to a PABX

Activating/deactivating call transfer – ECT (Explicit Call

Transfer)

Yes

Dialling options

Yes

Activating/deactivating the keypad during a call

Activating the keypad for the next connection

Operation of entrance telephone

Assigning internal users to the entrance telephone call Yes

group

Yes

Making calls with the entrance telephone

Call from the entrance telephone

Entrance telephone call waiting

Internal call with entrance telephone

Divert entrance telephone externally

Appendix

Yes

Predictive text

Yes

"Divert call waiting internally" is only available on the S1 and SL1 handsets.

The maximum number of entries in the speed dial list and the phonebook can vary.

The C1 handset has memory for a maximum of 50 entries, the C2 handset for a maxi-

mum of 100 entries, while you can store a maximum of 200 entries in the S1 and SL1

handsets.

The quick way into the world of ISDN

What is an MSN?

MSN = Multiple Subscriber Number. You can apply for up to ten different telephone

numbers for one multiple ISDN connection. An MSN is one of the phone numbers

assigned to you without an area code.

Your telephone uses the MSN entirely as you require. The following differentiation is

made:

Receive MSN: Phone numbers you may be called on. You can assign the receive

MSN's to specific internal users (terminals). Incoming calls are only forwarded to the

terminals to which the relevant receive MSN has been assigned. Terminals can be

handsets or answering machines.

Send MSN: Phone numbers that are assigned to the person you are calling. The net-

work operator calculates charges based on the send MSN's. You can assign a fixed

send MSN to each internal user.

Potential internal users are:

Handsets, to which you can assign the internal numbers 11 to 18.

Data modules (page 30), to which you can assign the internal numbers 41 to 48.

The integrated answering machines (on SX255isdn), which are assigned the inter-

nal phone numbers 91 to 93.

PC via USB interface, for which the internal number 40 is set aside.

Analogue terminals, to which you can assign the internal numbers 21 or 22.

Example of how to assign an MSN:

You have applied for four MSN's, two for business use (MSN1, MSN2) and two for private

purposes (MSN3, MSN4). Four handsets are connected to a base. Two handsets (Int.11

and 12) and the answering machine AM 91 are intended for business use, and two

handsets (Int.13 and 14) and the answering machine AM 92 are intended for private

use.

Internal users

handsets

Answering

machine

Use

Business

Receive MSN

MSN1, MSN2

Send MSN

MSN1

---

Int.11, 12

AM 91

Handset

Answering

machine

Int.13

Int.14

AM 92

Private

MSN3

MSN4

MSN3, MSN4

MSN3

MSN4

---

Further information for dealing with MSNs, e. g. setting the ring delay for each MSN,

can be found in the handset operating instructions.

Answering Machine

Your ISDN telephone has three answering machines (AM1, AM2, AM3). Once you have

connected your telephone, answering machine AM1 is shown and activated. By default,

answering machines AM2 and AM3 are hidden. To use them, they must be shown and

all shown answering machines must be assigned their own receive MSN. You can con-

figure AM1, AM2 and AM3 separately.

You can operate the answering machines

either directly using a registered handset (in the menu) or

by remote control (internal or external call to answering machine).

Remote control is a convenient option, allowing you day-to-day use of an answering

machine wherever you are. To configure the answering machines, you will need a hand-

set that is registered on the base (see handset operating instructions).

Definitions of terms used below:

Message

Memos

Message that a caller leaves on the answering machine.

"Spoken notes" that you can record on the answering machine for mem-

bers of your family or colleagues, for example.

AM mode

Recording or announcement.

The caller hears an announcement and may then leave a message.

Answer and record

mode

Announce only mode The caller hears your announcement but cannot leave a message.

If an answering machine is currently being used by one user (directly or

by remote control), then no other user can access the answering machine

during this time.

Operation using a registered handset

Which answering machine you can operate directly using your handset depends on the

assignment of the receive MSNs:

No MSN is assigned to the answering machines (factory setting):

AM1 answers all calls.

Each answering machine can be set, operated and played back from each handset/

terminal.

One or more MSNs are assigned to each answering machine:

Each answering machine can only be set and played back using handsets/terminals with

the same receive MSN.

Exception: If a receive MSN is assigned exclusively to one answering machine, and not

to any other handset/terminal, then this answering machine can be operated by all

internal users.

Answering Machine

Range of functions

Using a handset registered on the base, the following functions are available (see the

handset operating instructions for more details):

Configuration of answering machine

Assigning a receive MSN

Hiding/showing an answering machine

Specifying the number of rings before the answering machine starts

Deactivating/activating spoken date and time

Setting the recording time and recording quality

Activating/deactivating automatic pause

Locking the answering machine, defining AM PIN

Setting time control (only using S1 and SL1)

Activating/deactivating automatic listen in on the handset

Activating/deactivating automatic call pick up

Activating/deactivating automatic notification via text message

Operating the answering machines

Selecting an answering machine

Activating/deactivating the answering machine

Selecting announce only and AB mode

Recording/changing announcements

Playing back/deleting announcements

Recording memos

Two-way recording

Picking up a call while the answering machine is in operation

Playing back messages

Returning a call during playback

Playing a message to another caller

Playing back memos

Setting the playback speed (only using S1 and SL1)

Deleting messages/memos

Marking an old message or memo as "new"

Adding a number to the phonebook

Checking the status of an answering machine

Answering Machine

Remote control of answering machines

With the remote control option, you can operate your answering machine, e.g. listen to

and delete messages

from a registered handset, a connected cord telephone or

from external telephones and handsets.

Apart from the first step, the procedure is the same for both kinds of remote control.

The following functions are available when using remote control:

Activating/deactivating the answering machine

Messages and memos

– Play

– Skip

– Delete

Announcement

– Record

– Play

– Select

Recording internal memos

Help

Precondition:

For external operation, you must change the answering machine PIN for your

own security (factory setting: 0000).

In order to be able to use the full range of functions of this mode, you must enable

"Remote control" and "Remote delete" on the base (see handset operating instruc-

tions).

Starting remote control

Operating the answering machine while you are away from home

For remote control you need a telephone that transmits DTMF tones (tone dialling). It is

important to enter the AM PIN immediately while the announcement is being played. In

addition Remote control and, if required, Remote delete must be activated.

Dial your own telephone number.

When the announcement starts, enter the AM PIN at

once.

Operating the answering machine from the handset (internal)

There is a voice-controlled help for the two-key functions;

Help with deleting

0 ;

Help with new messages/phrases

: ;

Help with recording

F ;

9 ;

Help with modes

Answering Machine

Added-feature and standard handset

Open list of internal users.

Enter internal phone number for the answering

machine: 91 or 92 or 93.

u INT

Enter AM PIN if required.

Handset made by another manufacturer (GAP mode)

Lift the receiver. If necessary, press another key to

initiate an internal call.

Enter internal phone number for the answering

machine: 91 or 92 or 93.

Enter AM PIN if required.

Cordless phone adapter and normal telephone

Automatic line seizure must be deactivated (see handset operating

instructions). As supplied, automatic line seizure is activated!

Lift the receiver.

Enter internal phone number for the answering

machine: 91 or 92 or 93.

Enter AM PIN if required.

Key sequences for remote control

Once you have initiated remote control of the answering machine, the functions of the

keys are the same for all telephones.

Pause/Stop

Record

Announce-

ment

On/Off

Operating mode

New

Delete

Status/Help

;

Answering Machine

Activating/deactivating the answering

machine

Activate/deactivate

Playing back messages and memos

All messages

New messages only

Pause/Stop

: B

Continue playback

End playback

E E

Skipping messages and memos

To start of message

To previous message

To next message

A A

Deleting messages and memos

Single message during playback

0 B

All messages after playback

Recording an announcement

Announcement 1

F G A

F G B

F G 3

Announcement 2

Announcement

Concluding announcement

F G D

Playing back an announcement

Announcement 1

G A

G B

G 3

G D

Announcement 2

Announcement

Concluding announcement

Answering Machine

Selecting an announcement

Announcement 1

9 A

9 B

9 3

9 D

Announcement 2

Announcement

Concluding announcement

Recording internal memos

Begin recording

F B

End recording

Help

Check settings

;

Check one-key functions

; ;

see page 22

Check two-key functions

End check

Connecting devices

Connecting cord-based analogue devices

The internal phone numbers Int.21/Int.22 are pre-assigned to the TAE connections.

Devices connected to them must

not be registered on the base.

be set to tone (DTMF) dialling (pulse dialling not supported).

In addition, the corresponding device type must be set and device-specific additional

settings made.

No costs are displayed on the connected devices. However, accumulated costs are

recorded on the base and can be checked using an added-feature handset or on a PC.

Device types

The following settings are possible (Defining the device type, see Page 29).

see Page 26, Connecting telephones

see Page 27, Connecting a fax machine

see Page 27, Connecting a modem

see Page 27, Connecting an answering machine

see Page 27, Connecting a fax machine

see Page 31, Connecting door type 1

see Page 32, Connecting door type 2

see Page 28, No device connected

N Telephone

N Fax

N Modem

N Answering mach.

N Neutral

N Door type1

N Doortype2(DTMF)

N No function

Note the explanations below for the device types and their additional

device-specific settings.

Connecting telephones

By default, the two TAE connections are set to Telephone.

This means that the base is ready to use with a telephone (with tone dialling/DTMF) con-

nected to Int.21 or Int.22 even without a handset.

If you also want to use this telephone to make internal calls, automatic line seizure for

the associated TAE connection must be deactivated. For external connections, it is then

necessary to dial a zero first.

Information on making calls using devices on the TAE connection can be found in the

handset operating instructions.

Connecting devices

Connecting a fax machine

To operate a fax machine or a combination device (e.g. fax with telephone), the device

type setting should be changed to Fax or Neutral.

For problem-free fax operation regardless of the settings of the remote terminal, the

device type setting Neutral is recommended (with the Fax setting, a successful fax con-

nection depends on the settings of the remote terminal).

If you only want to make external connections, automatic line seizure for the associated

TAE connection must remain activated. In this case, the fax machine or combination

device should be set to "Operate on main connection".

If, on the other hand, you also want to make internal connections, automatic line sei-

zure for the associated TAE connection must be deactivated. For external connections,

it is then necessary to either dial a zero before each number or set the fax machine or

combination device to "Operation on PABX" (see fax machine or combination device

operating instructions).

Use the opportunity to assign the fax a separate phone number (MSN). Assign the cor-

responding TAE connection an exclusive receive MSN (see handset operating instruc-

tions).

In the device type setting Fax, Call waiting and Hunt group are not supported.

In the device type setting Neutral, Call waiting is not supported. When connecting a

fax only device, Hunt group should be deactivated (see handset operating instruc-

tions).

Connecting a modem

To operate a modem, the device type setting must be changed to Modem.

If you only want to make external connections, automatic line seizure for the associated

TAE connection must remain activated (see handset operating instructions). In this case,

the modem should be set to "Operate on main connection".

If, on the other hand, you also want to make internal connections, automatic line sei-

zure for the associated TAE connection must be deactivated. For external connections,

it is then necessary to either dial a zero before each number or set the modem to "Oper-

ation on PABX" (see modem operating instructions).

Connecting an answering machine

If you want to operate an answering machine (or a telephone with integrated answering

machine) on the TAE connection, the device type setting Answering mach. is recom-

mended. In this setting, the answering machine can pick up a call.

If a telephone with integrated answering machine is connected and you want to use this

telephone to make internal calls, automatic line seizure for the associated TAE connec-

tion must be deactivated (see handset operating instructions). For external calls, it is

then necessary to dial a zero first.

In the device type setting Answering mach., Call waiting and Hunt group are not sup-

ported (see handset operating instructions).

Connecting devices

No device connected

For each TAE connection, to which no device is connected, the device type must be set

to No function, in order to prevent malfunctioning of the Reject all (see handset oper-

ating instructions) and Busy on busy (see handset operating instructions) ISDN func-

tions.

Making calls with devices on the analogue connection

(TAE connection)

Telephones with tone dialling (DTMF = dual tone multi-frequency dialling) can be oper-

ated on the analogue connections. Telephones with pulse dialling are not supported.

Automatic line seizure

With automatic line seizure activated, the external line is seized as soon as the receiver

is lifted. As a consequence, normal internal dialling is no longer possible. However, an

internal call is still possible by way of an internal enquiry using the S key. You can acti-

vate automatic line seizure with any added-feature handset (see added-feature handset

operating instructions).

Making external calls

Auto. line seizure inactive

Auto. line seizure active

c Q ~

c ~

Making internal calls

Auto. line seizure inactive

c ~

Group call to all internal users

Auto. line seizure inactive

c P / with GAP INT P

Call waiting

You hear the call waiting tone during your external call.

either ...

a Call disconnected, wait for ring c

or ...

S Caller 1 on hold.

Switch to waiting caller – Toggling

Caller 1 on hold.

Caller 2 on hold etc.

Connecting devices

Making an external enquiry

S Q ~

Switch between callers if necessary.

Making an internal enquiry

S ~

Switch between the callers if necessary.

Transfer call before/after answer

either ...

S ~

Transfer before answer:

Hold down (return to idle status).

or ...

Transfer after answer:

Transfer call after answer.

Making an enquiry call.

S ~

Hold down (return to idle status).

Picking up a call while the answering machine is in operation

You can pick up a call, even if the answering machine has already switched itself on on

the second analogue connection, your announcement is running, or the caller is already

leaving a message. When you pick up the call the recording stops.

You can deactivate automatic call pick up (see handset operating instructions) and carry

on an existing call, while the answering machine is switched on.

Automatic line seizure must be deactivated (page 28).

Automatic call pick up (factory setting) Automatic call pick up inactive

c O S

The requirement for call pick up is that the answering machine and the

internal user picking up the call are assigned the same receive MSN

(page 19) and the device type Answering mach. is set for the internal

number of the answering machine (page 27).

Defining the device type

You must define the device type on the handset or PC. You can find more information

in the operating instructions for your handset or PC software.

Connecting devices

Connecting PC via USB

You can connect a PC with a cable using the USB port on your base and connect one or

more PCs without a cable using the Gigaset M10x data modules.

Your base then offers you the option of using a connected PC to:

Configure your base

Manage phonebooks from the PC, base and handsets.

Using a PC connected with a cable or via a Gigaset M101 Data, you can also fax from the

PC (using fax emulation with no hardware requirements).

In conjunction with the enclosed software (talk&surf 6.0) this offers you the option of

using data transmission and the Internet from the PC using the ISDN network access

on your base (e. g. surfing the Internet, e-mail, home banking).

Transmit data between different PCs.

You can find further information in the instructions for the software

(talk&surf 6.0).

Wireless PC connection: Gigaset M101 Data and

Gigaset USB-Adapter DECT/M105 data modules

The Gigaset M101 Data with V24 interface and the Gigaset DECT/M105 USB Adapter

with USB interface give you the option of establishing a wireless connection between

your PC and the base. A connection via a Gigaset M10x Data data module provides you

with a 64 kbit/sec. interface.

The internal phone numbers PC 41 to PC 48 are set aside for this purpose on your base.

For installation, see the installation instructions on the CD-ROM enclosed with the data

module.

Wire-based PC connection: Base USB port

You can establish a wire-based connection to a PC using the USB port on your base

(page 7). The internal phone number PC 40 is set aside for this purpose on your base.

1. Plug the USB cable into the base only first of all (do not connect it with the PC im-

mediately).

2. Only connect the USB cable to the PC when prompted to do so by the PC program

talk&surf 6.0.

A wire-based connection via the USB port on the base provides you with a 128 kbit/sec.

interface.

Gigaset Repeater

You can increase the range of your handsets with the Gigaset Repeater. Your telephone

is set up to use a Gigaset Repeater (accessory). To ensure the Repeater is installed cor-

rectly, Repeater mode must be activated on the base (see handset operating instruc-

tions).

Operation of entrance telephone

For details of setting up an entrance telephone, refer to the handset operating instruc-

tions.

Connecting entrance telephones

In case of questions about the entrance telephones shown here or any other systems,

please contact the respective manufacturers or suppliers.

We ask for your understanding that Siemens AG cannot provide any guarantee of the

currency, completeness and accuracy of the circuit diagrams.

Several examples are illustrated below. Current circuit diagrams are available from your

retailer.

Door type 1

The following examples provide guidance for connecting entrance telephones using a

TFE adapter (door type 1).

Siedle TLM 512/612, TLE 061, CTB 711

Gigaset SX205-255i

Ritto entrance telephone and door opening system

Operation of entrance telephone

Caution!

Connect base power unit 6573 and additional unit TFV5680 using

enclosed bus connector.

Ritto TwinBus entrance system

Gigaset SX205-255i

Caution!

Connect base power unit 4753/01 and additional unit TFV4680/00 using

enclosed bus connector.

Door type 2 (DTMF)

For details of connecting entrance telephones with DTMF control (door type 2), refer to

the example below.

Deutsche Telekom DoorLine

Gigaset SX205-255i

Appendix

Care

Wipe the base and handset with a damp cloth (no solvents) or an antistatic cloth. Never

use a dry cloth. This can cause static discharge.

Contact with liquid

If the handset should come into contact with liquid, on no account switch the device

on. Remove all batteries immediately.

Allow the liquid to drain out of the device, and then pat all parts of the device dry.

Keep the handset with the batteries removed in a warm, dry place for at least 72 hours.

In many cases, you will then be able to use it again.

Questions and Answers

If you have any questions about the use of your phone, you can contact us 24 hours a

day at www.my-siemens.com/customercare. You will find the most frequently asked

questions and the corresponding answers below.

What has happened if … Possible Cause

Possible solution

… the handset or the base

does not ring?

The ringer is switched off.

Activate the ringer for the

handset or the base.

Switch off call forwarding.

Deactivate night service.

(see handset operating instruc-

tions)

Call forwarding is set to Immedi-

ately.

Night service is active.

… the answering machine

The system PIN entered is incor- Enter the system PIN again or

says "PIN is incorrect" during rect or still set to 0000.

remote control?

set a PIN that is different from

0000

(see handset operating instruc-

tions).

… the answering machine

does not record any messages

or has automatically switched

over to 'announce only'?

Its memory is full.

Delete old messages

Play back new messages and

delete.

(see handset operating instruc-

tions)

… there are no incoming

calls?

"Constant" call forwarding is acti- Deactivate "Constant" call for-

vated. warding.

The MSN has not been assigned Determine the receive MSN.

to the internal user.

The "internal" authorisation is

set.

Change the authorisation.

(see handset operating instruc-

tions)

… the telephone also rings for The phone number is in the

Delete the corresponding

fax-PC calls?

phone number list on the base. phone number (MSN) in the

list.

(see handset operating instruc-

tions)

Appendix

What has happened if … Possible Cause

Possible solution

… you have a PABX and, after You have entered the wrong pre- Check and correct the prefix

dialling, the wrong connec-

tion or no connection is

made?

fix.

(see handset operating instruc-

tions).

… some of the ISDN func-

The ISDN function has not been Check with your network pro-

vider.

tions do not work as stated? enabled.

… another telephone on the The same MSN was assigned to Deactivate internal call divert

So bus does not ring?

the telephones. One of the tele- or set external call divert

phones also has internal call

(see handset operating instruc-

divert activated.

tions).

Service (Customer Care)

You can get assistance easily when you have technical questions or questions about

how to use your device by using our online support service on the Internet at:

www.my-siemens.com/customercare

or by referring to the section entitled Questions and answers in this manual

(page 33).

Appendix

If the device needs to be repaired, please contact one of our Customer Care Centers:

Abu Dhabi. . . . . . . . . . . . . . .0 26 42 38 00

Argentina . . . . . . . . . . . . 0 80 08 88 98 78

Australia . . . . . . . . . . . . . . .18 00 62 24 14

Austria . . . . . . . . . . . . . . . .05 17 07 50 04

Bahrain . . . . . . . . . . . . . . . . . . . . . 40 42 34

Bangladesh. . . . . . . . . . . . . . 0 17 52 74 47

Belgium . . . . . . . . . . . . . . . . 0 78 15 22 21

Bosnia Herzegovina . . . . . . .0 33 27 66 49

Brazil. . . . . . . . . . . . . . . . 0 80 07 07 12 48

Brunei . . . . . . . . . . . . . . . . . . . 02 43 08 01

Bulgaria. . . . . . . . . . . . . . . . . . 02 73 94 88

Cambodia . . . . . . . . . . . . . . . . 12 80 05 00

Canada . . . . . . . . . . . . . . 1 88 87 77 02 11

China . . . . . . . . . . . . . . . 0 21 50 31 81 49

Croatia . . . . . . . . . . . . . . . . . 0 16 10 53 81

Czech Republic . . . . . . . . . .02 33 03 27 27

Denmark. . . . . . . . . . . . . . . . . 35 25 86 00

Dubai . . . . . . . . . . . . . . . . . . 0 43 96 64 33

Egypt. . . . . . . . . . . . . . . . . . . 0 23 33 41 11

Estonia . . . . . . . . . . . . . . . . . . 06 30 47 97

Finland . . . . . . . . . . . . . . . .09 22 94 37 00

France. . . . . . . . . . . . . . . . .01 56 38 42 00

Germany. . . . . . . . . . . . . . .01805 333 222

Greece . . . . . . . . . . . . . . 0 80 11 11 11 16

Hong Kong . . . . . . . . . . . . . . . 28 61 11 18

Hungary . . . . . . . . . . . . . . .06 14 71 24 44

Iceland . . . . . . . . . . . . . . . . . . . 5 11 30 00

India . . . . . . . . . . . . . . 01 13 73 85 89 - 98

Indonesia . . . . . . . . . . . . 0 21 46 82 60 81

Ireland . . . . . . . . . . . . . . . .18 50 77 72 77

Italy. . . . . . . . . . . . . . . . . . .02 66 76 44 00

Ivory Coast . . . . . . . . . . . . . . . 80 00 03 33

Jordan. . . . . . . . . . . . . . . . . . 0 64 39 86 42

Kenya . . . . . . . . . . . . . . . . . . . . 2 72 37 17

Kuwait . . . . . . . . . . . . . . . . . . . 2 45 41 78

Latvia . . . . . . . . . . . . . . . . . . . . 7 50 11 14

Lebanon . . . . . . . . . . . . . . . . . 01 44 30 43

Libya . . . . . . . . . . . . . . . . . .02 13 50 28 82

Lithuania. . . . . . . . . . . . . . . . 8 22 74 20 10

Luxembourg . . . . . . . . . . . . . 43 84 33 99

Macedonia. . . . . . . . . . . . . . . . 02 13 14 84

Malaysia. . . . . . . . . . . . . . . 03 21 63 11 18

Malta . . . . . . . . . . . . 00 35 32 14 94 06 32

Mauritius . . . . . . . . . . . . . . . . . . 2 11 62 13

Mexico. . . . . . . . . . . . . .01 80 07 11 00 03

Morocco . . . . . . . . . . . . . . . . . 22 66 92 09

Netherlands. . . . . . . . . . . . 0900-3333102

New Zealand . . . . . . . . . . . 08 00 27 43 63

Norway . . . . . . . . . . . . . . . . . . 22 70 84 00

Oman. . . . . . . . . . . . . . . . . . . . . . 79 10 12

Pakistan . . . . . . . . . . . . . . . 02 15 66 22 00

Philippines. . . . . . . . . . . . . . 0 27 57 11 18

Poland . . . . . . . . . . . . . . . . 08 01 30 00 30

Portugal. . . . . . . . . . . . . . . . 8 00 85 32 04

Qatar . . . . . . . . . . . . . . . . . . . . 04 32 20 10

Romania . . . . . . . . . . . . . . 02 12 04 60 00

Russia. . . . . . . . . . . . . . . . (800) 200 10 10

Saudi Arabia . . . . . . . . . . . . 0 22 26 00 43

Serbia. . . . . . . . . . . . . . . . . 01 13 22 84 85

Singapore . . . . . . . . . . . . . . . . 62 27 11 18

Slovak Republic . . . . . . . . . 02 59 68 22 66

Slovenia. . . . . . . . . . . . . . . . 0 14 74 63 36

South Africa. . . . . . . . . . . . 08 60 10 11 57

Spain . . . . . . . . . . . . . . . . . . 9 02 11 50 61

Sweden . . . . . . . . . . . . . . . . 0 87 50 99 11

Switzerland . . . . . . . . . . . . 08 48 21 20 00

Taiwan . . . . . . . . . . . . . . . . 02 25 18 65 04

Thailand. . . . . . . . . . . . . . . . 0 22 68 11 18

Tunisia . . . . . . . . . . . . . . . . . 0 71 86 19 02

Turkey . . . . . . . . . . . . . . .0 21 65 79 71 00

Ukraine . . . . . . . . . . . . . .8 80 05 01 00 00

United Arab Emirates . . . . . 0 43 31 95 78

United Kingdom . . . . . . .0 87 05 33 44 11

USA . . . . . . . . . . . . . . . . .1 88 87 77 02 11

Vietnam. . . . . . . . . . . . . . . . . . 45 63 22 44

In some countries repair and replace services are impossible where the products are not

sold through our authorised dealers.

Your Gigaset is designed for operation in your country, as indicated on the packaging

and on the device itself. Country-specific conditions have been taken into account. If

you have any questions about the differences between the public phone networks,

please contact your specialist dealer or network provider.

The CE mark attests to the phone's compliance with the essential requirements of the

R&TTE directive.

Appendix

Excerpt from the original declaration

"We, Siemens AG, declare that the above mentioned product is manufactured according to our Full

Quality Assurance System certified by CETECOM ICT Services GmbH in compliance with ANNEX V

of the R&TTE Directive 99/05/EC. The presumption of conformity with the essential requirements

regarding Council Directive 99/5/EC is ensured"

Senior Approvals Manager

The Declaration of Conformity (DoC) has been signed. In case of need a copy of the original DoC

can be made available via the company hotline.

Specifications

DECT standard

GAP standard

supported

No. of channels

Radio frequency range

Duplex method

Channel grid

120 duplex channels

1880 MHz to 1900 MHz

Time multiplex, 10 ms frame length

1728 kHz

Bit rate

1152 kbit/s

Modulation

GFSK

Language code

Transmission power

32 kbit/s (ADPCM)

10 mW, average power per channel

up to 300 m in the open air

up to 50 m in buildings

220/230 V ~/50 Hz (power unit SNG 8-a)

In standby mode approx. 4.6W

In call mode:

with handset approx. 4.6W

with telephone (TAE) approx. 5.2 W

+5 °C to +45 °C

20 % to 75 % humidity

Euro-ISDN-Multiple Connection IAE

Jack: TAE 6, F/N coding

Dialling mode: DTMF (tone dialling)

Data transmission rate: max. 28.8 kbit/s

approx. 152 x 213 x 61 mm (H x W x D)

0.350 kg

Range

Power supply

Power consumption

Environmental conditions for

operation

ISDN connection

TAE socket (INT 21/22)

Base dimensions

Base weight

Power supply cord approx. 3 m

ISDN connection cable approx. 3 m

USB cable approx. 3 m

Length of cables

Accessories

Gigaset Handsets

Turn your Gigaset into a cordless telephone system:

Gigaset S1 Handset

Large illuminated graphic display with date and time

Phonebook for around 200 entries

Full duplex grade handsfree

SMS

EATONI predictive text

Caller-specific ringer melody setting

(for VIP calls)

Download options for obtaining melodies via SMS

Room monitor

Walkie talkie

Voice dialling for 29 names

Announce name when calling

Gigaset SL1 Handset

Large illuminated graphic display with date and time

Illuminated keypad

Phonebook for around 200 entries

Full duplex grade handsfree

SMS

EATONI predictive text

Caller-specific ringer melody setting

(for VIP calls)

Download options for obtaining melodies via SMS

Room monitor

Walkie talkie

Voice dialling for 29 names

Announce name when calling

Vibration alarm

Connector jack for headset, PC and MP3 player

Accessories

Gigaset C2 Handset

Graphic display with date and time

Phonebook for around 100 entries

Handsfree

SMS

EATONI predictive text

Caller-specific ringer melody setting

(for VIP calls)

Room monitor

Walkie talkie

Gigaset C1 Handset

Graphic display with date and time

Phonebook for around 50 entries

Handsfree

SMS

Gigaset Repeater

The Gigaset Repeater can be used to increase the reception

range of your Gigaset handset to the base.

Accessories

Gigaset Data Modules

A Gigaset data module allows you to create a wireless connection between your PC and

your Gigaset.

Gigaset USB Adapter DECT/M105

Data transmission at up to 90 kbit/s

Connection between computer and

Gigaset or between two computers

No external power supply necessary (powered by

the computer)

Range of up to 50 m in buildings

Range of up to 300 m in the open air

Mobile handsfree set with PTT key

With the mobile handsfree set you can make a call while

keeping your hands free.

In addition, conversations can be heard on the handset.

All accessories and batteries are available from your mobile phone retailer. Or you can

order direct online from the my-siemens Online Shop: www.my-siemens.com/shop .

The Online Shop also has the latest product information.

ISDN glossary

Added-feature connection

ISDN connection that offers three more services than the standard connection: Call

forwarding, transfer of charges after the connection, and a T-mailbox.

AOC-D

Advice of Charge: During the Call. Transfers the charge information during the con-

nection.

AOC-E

Advice of Charge: at the End of the Call. Transfers the charge information at the end

of the connection.

Authorisation class

Defines which connections are permitted on a PABX terminal, e.g., internal only,

incoming only, or unlimited call authorisation.

Authorisation for direct outward dialling

Different users may be assigned different levels of authorisation on a base station.

For example, while User A may only take incoming calls, User B may make calls with-

out restriction.

Automatic callback

See "Callback when the number is busy"

Automatic redial

Several attempts to call are made automatically when the line is busy.

Block dialling

Also pre-dialling. You may only dial or, if required, correct the phone number. Then

you should lift the receiver or press the loudspeaker key.

Call divert

CF, Call forwarding. You want to forward calls to another number permanently. You

can divert calls externally via the exchange or internally in the device itself. Call

divert can be set up individually for each separate phone number (MSN) (to your

mobile phone when on holiday, to the office, to a neighbour etc.).

This is carried out at the network provider's local exchange. This means the call

never reaches the original destination.

There are three kinds of call divert: immediate (CFU, Call Forwarding Unconditional),

when the line is busy (CFB, Call Forwarding Busy), and when the call is not answered

(CFNR, Call Forwarding No Reply).

ISDN glossary

Call divert (via second B channel) / internal call divert

While external call divert takes place in the local telephone exchange of the network

provider, internal call divert is implemented by your telephone. Your telephone for-

wards the call via the second line of your ISDN connection. This means both phone

lines are engaged for the duration of the call. You pay the charges for the connec-

tion to the forwarding number. However, you save yourself the network provider's

charges for this function.

Call forwarding during the call phase

CD, Call Deflection. Must be explicitly enabled by the network provider for each ISDN

connection. CD enables an incoming call to be forwarded to any phone number

while it is ringing, without having to answer the call. Because the caller cannot

affect on where it is forwarded (for example, to a mobile phone), you will pay the

resulting charges. The caller must only pay the normal telephone charges to the con-

nection he dialled.

Call transfer (e.g., for ISDN PABX's)

ECT, Explicit Call Transfer. User A calls User B. He puts the connection on hold and

calls User C. Rather than connect everyone in a three-party conference, A now trans-

fers User B to C and hangs up.

Call waiting

CW, Call Waiting. Service provided by the network provider. An acoustic signal dur-

ing a call indicates that another caller is waiting. In addition, ISDN phones indicate

this with a displayed message. You can then decide whether to accept or reject the

second call.

Call waiting protection

Deactivates the call waiting signal.

Callback when the call is not answered

If a user does not respond when called, a caller can arrange an automatic callback.

As soon as the destination phone has completed a call and is free again the caller is

rung back. This service must be supported by the exchange. The ringback request is

automatically cancelled after approximately 2 hours (depending on the telephone

exchange.

Callback when the number is busy

Callback must first be activated on the caller's terminal. A connection is established

automatically as soon as the destination phone is no longer busy. As soon as the

connection is free the caller is rung back. As soon as the caller lifts his receiver the

connection is made automatically.

Caller identification

Displays caller's phone number, name or type of connection (e.g., exchange/inter-

nal) on the telephone screen.

Caller list

Depending on the setting, the calls list contains callers you haven't reached, or those

you have spoken to. The last 20 missed calls and the last 20 accepted calls are stored

with their phone number, date and time. If you wish to do so, you can return the call

to these users directly from this list.

ISDN glossary

Capture

Performance feature "Identify/capture". MCID stands for "Malicious Call Identifica-

tion". If you receive annoying calls, you can have the telephone exchange store the

caller number. This performance feature must be requested from the network pro-

vider.

CCBS (Completion of Calls to Busy Subscriber)

See "Callback when the number is busy"

CCNR (Completion of Calls No Reply)

See "Callback when the call is not answered"

CD (Call Deflection)

See "Call forwarding during the call phase"

CF (Call forwarding)

See "Call divert"

Channel

Like an analogue connection, an ISDN connection enters the building through two

cables, but for ISDN a distinction is made between the two bearer channels called

the B-channels (which have nothing to do with the physical cables!) and the control

channel, otherwise known as the D channel.

Charge detail display

See "AOC-D" and "AOC-E"

CLI (Calling Line Identification)

The caller's phone number is transmitted.

CLIP (Calling Line Identification Presentation)

User A calls User B. A's phone number appears on B's telephone display.

CLIR (Calling Line Identification Restriction)

Stops your personal phone number being displayed.

CNIP (Calling Name Identification Presentation)

User A calls User B. A's name appears on B's telephone screen.

COLP (Connected Line Identification Presentation)

User A calls User B. B's phone number is displayed on A's telephone. If B has pro-

grammed call forwarding to C: then the dialled number and transferred number are

not identical, and the phone number of C is displayed if C permits his phone number

to be displayed.

COLR (Connected Line Identification Restriction)

If C has set up COLR, then C's phone number is not displayed on A's phone.

Conference call

See "Three-party conference"

CW (Call Waiting)

See "Call waiting"

ISDN glossary

D channel

Control channel for an ISDN connection. See "Channel"

Digital exchange

Computer controlled switching units allow quick connection and the activation of

such additional services as => enquiry calls, => call waiting, => three-way confer-

ence, => call forwarding etc.

Direct call

Block the telephone for all phone numbers except for an individually entered

number. After picking up the handset and pressing any key, the connection to the

saved phone number is established. Ideal for children who cannot yet dial phone

numbers (baby call). Calling an emergency number is always possible. This function

is available on the Gigaset 3000/2000 Comfort handsets.

ECT (Explicit Call Transfer)

See "Call transfer"

Electronic code lock

Personal code (=> PIN), used, for example, to protect a phone against unauthorised

use – only calls to emergency numbers may still be made. Incoming calls may be

accepted.

Enquiry calls

You are making a call. Using the "Enquiry call" function, you interrupt the conversa-

tion briefly to establish a second internal or external connection to another user. If

you terminate the connection to this user immediately, then this was an enquiry call.

If you switch to and fro between the first and second user, it is called toggling.

Exchange

Nodal point in the public telephone network. A distinction is made, for example,

between local exchanges and long-distance or trunk exchanges.

Handsfree

A phone's handsfree set not only permits open listening but also allows you to talk

to the person on the other end without lifting the receiver by means of an integrated

microphone. This means others present in the room can also participate in the con-

versation.

Hold

(Hold the line). Interrupts and re-instates an existing connection. In particular, it per-

mits enquiry calls and toggling between calls.

ISDN glossary

Internal calls

Connection between the base station and handsets made free of charge.

Internal ringer

Special ringtone on PABX's to distinguish between internal and external calls.

ISDN

Abbreviation for Integrated Services Digital Network, i.e., a digital network for inte-

grating services. This includes the integration of telephone, fax or data transmis-

sion.

ISDN abbreviations

Call waiting

Call divert

3PTY

CCBS

Three-party conference

Callback when the number is busy

Call forwarding during the call phase

Keypad

The keypad supports special function keys such as the star (*) and hash (#) keys.

In this way, special functions offered by your network provider can be initiated using

a code, such as "#4711*".

MCID (Malicious call identification)

See "Capture"

MSN

Multiple Subscriber Number. The phone numbers belonging to a multiple ISDN con-

nection. Each terminal is addressed separately, e.g., a separate number for a fax

machine. There are three MSN in the basic price for the standard and comfort con-

nection. Up to ten MSN can be assigned to one ISDN connection.

Multiple connection

ISDN connection that has up to ten MSN available, in contrast to the system connec-

tion with one call director number block. This is the preferred type of ISDN connec-

tion for private customers.

Multiple subscriber number

See "MSN"

Music on hold

See "Wait melody"

Mute

Convenience feature for telephones, which deactivates the built-in microphone (in

handset or handsfree unit).

ISDN glossary

Notebook function

During a phone call you can enter a phone number in the phone's temporary mem-

ory to be dialled later.

NT/NTBA

Network terminating device (NT = Network Terminator and NTBA = Network Termi-

nator Basic Access). The public T-ISDN is terminated with an NT. The NT acts as a

bridge to the existing telephone outlet. Only the NT can or may be connected to the

telephone outlet. Under no circumstances should analogue terminals also be con-

nected to the phone outlet. ISDN terminals and additional ISDN outlets are con-

nected to the NT.

Open listening

At the touch of a key, all those present in a room can listen in to a phone call via an

integrated loudspeaker. See also "Handsfree talking".

Outgoing MSN, freely selectable

A feature which helps you to individually determine which MSN should be used for

the following call. This is not only important for the phone number display on the

called handset but also for billing charges. This is because call charges, which can be

broken down free of charge according to MSN on the network provider invoice, are

billed according to the MSN used to make the call.

Parking

A call is parked when you want to unplug the telephone during a call, or you want

to continue your call from another telephone with the same connection. The con-

nection is retained while it is parked.

Phonebook

An added feature on a phone allowing the name and phone number of several users

to be stored. The phone numbers can quickly be found and dialled.

Abbreviation for Personal Identification Number. Protects against unauthorised use,

e.g., system PIN, answering machine PIN, handset PIN.

Plugging to bus

TP, Terminal Portability. Also called parking. An incoming call can be held at the local

exchange for up to three minutes to then be accepted, for example, by another

phone, a fax machine or a PC. In the meanwhile the caller hears an appropriate

announcement.

Pre-dialling, see also "Block dialling"

For some telephones with a display you can enter the phone number first, and check

it once more before dialling.

ISDN glossary

Remote activation

Allows the answering machine to be activated and deactivated during a call. This

function is PIN-protected.

Remote check

Answering machine function. Listen to messages remotely, mostly together with

options like delete messages or change announcements.

Repeater

A repeater increases the range of a handset connected to a base station. The device

receives the radio signal from the base station and broadcasts it further.

Ring delay

For each internal party, you can specify how many rings take place before this party

hears the ring. This can also be set for each MSN phone number.

For example, your handset, in addition to the base telephone (which rings on the

first ring) could ring after three rings for the private phone number, and ring on the

first ring for the business phone number.

S0 Bus

Four-wire ISDN connection wiring. It provides two B-channels and one D-channel.

Up to twelve ISDN outlets can be connected to it, on which up to eight terminals can

be operated at the same time.

Standard connection

ISDN connection with a series of services such as call waiting, three-party confer-

ence, or callback when the number is busy. See also "Comfort connection".

Three-party conference

3PTY, three-party. Interconnection with two external users (ISDN or analogue net-

work customers).

Toggling

Toggling allows you to switch between two external callers without allowing the

waiting caller to listen in.

Terminal Portability, see "Plugging to bus".

Two-way recording of phone calls

Answering machine feature which allows you to record a conversation during a

phone call.

ISDN glossary

Wait melody

Music on hold. During an enquiry call or when a call is being transferred, a melody

is played which the waiting person can hear.

Withhold own number (CLIR)

Stops your personal phone number being transferred.

Index

Power supply cord. . . . . . . . . . . . . . .6

USB cable . . . . . . . . . . . . . . . . . . . .30

Call

Divert. . . . . . . . . . . . . . . . . . . . . . .41

Call divert . . . . . . . . . . . . . . . . . .40, 41

Call forwarding . . . . . . . . . . . . . . . . .41

Call waiting . . . . . . . . . . . . . . . . . . . .41

Call waiting protection . . . . . . . . . . . .41

Callback

Accessories . . . . . . . . . . . . . . . . . . . . 37

Added-feature connection . . . . . . . . . 40

Analogue

Making calls with analogue

devices . . . . . . . . . . . . . . . . . . . . 28

Announce only (answering machine) . 20

Announcement (answering machine)

Note . . . . . . . . . . . . . . . . . . . . . . . 20

Announcement (answering

When the number is busy . . . . . . . .41

Callback when the call is not

machine) . . . . . . . . . . . . 20

answered . . . . . . . . . . . .41

Answer and record (answering

Caller identification . . . . . . . . . . . . . .41

Caller list . . . . . . . . . . . . . . . . . . . . . .41

Capture . . . . . . . . . . . . . . . . . . . . . . .42

Care of the telephone. . . . . . . . . . . . .33

CF, see also Call divert

Channel. . . . . . . . . . . . . . . . . . . . . . .42

Charge detail display . . . . . . . . . . . . .42

CLI. . . . . . . . . . . . . . . . . . . . . . . . . . .42

CLIP. . . . . . . . . . . . . . . . . . . . . . . . . .42

CLIR. . . . . . . . . . . . . . . . . . . . . . . . . .42

CNIP . . . . . . . . . . . . . . . . . . . . . . . . .42

Conference call . . . . . . . . . . . . . . . . .42

Connecting

Answering machine . . . . . . . . . . . .27

Auxiliary equipment . . . . . . . . . . . . .7

Base . . . . . . . . . . . . . . . . . . . . . . . . .6

Devices. . . . . . . . . . . . . . . . . . . . . .26

Fax machine . . . . . . . . . . . . . . . . . .27

Modem . . . . . . . . . . . . . . . . . . . . .27

Telephone . . . . . . . . . . . . . . . . . . .26

Connecting a fax machine . . . . . . . . .27

Connecting a modem. . . . . . . . . . . . .27

Connecting auxiliary equipment . . . . . .7

Connection

machine) . . . . . . . . . . . . 20

Answering machine. . . . . . . . . . . . . . 22

Announcement . . . . . . . . . . . . . . . 20

Connecting . . . . . . . . . . . . . . . . . . 27

Key sequences for remote control . . 23

Memos . . . . . . . . . . . . . . . . . . . . . 20

Messages. . . . . . . . . . . . . . . . . . . . 20

Operating from handset . . . . . . . . . 22

PIN . . . . . . . . . . . . . . . . . . . . . . . . 22

Remote control . . . . . . . . . . . . . . . 22

Remote delete . . . . . . . . . . . . . . . . 22

AOC-D . . . . . . . . . . . . . . . . . . . . . . . 40

AOC-E. . . . . . . . . . . . . . . . . . . . . . . . 40

Authorisation class . . . . . . . . . . . . . . 40

Authorisation for direct outward

dialling . . . . . . . . . . . . . 40

Automatic callback . . . . . . . . . . . . . . 40

Automatic redial . . . . . . . . . . . . . . . . 40

Base

as desktop unit . . . . . . . . . . . . . . . . 4

Connecting . . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . . . . . 3

Installation (notes). . . . . . . . . . . . . . 4

Installation location . . . . . . . . . . . . . 4

Preparing for use . . . . . . . . . . . . . . . 4

Setting . . . . . . . . . . . . . . . . . . . . . . 8

Wall mounting . . . . . . . . . . . . . . . . . 5

Block dialling. . . . . . . . . . . . . . . . . . . 40

TAE . . . . . . . . . . . . . . . . . . . . . . . .26

Connector

Mini-Western . . . . . . . . . . . . . . . .6, 7

TAE . . . . . . . . . . . . . . . . . . . . . . .6, 7

Contact with liqui d . . . . . . . . . . . . . . .33

Customer Care (Service) . . . . . . . . . . .34

Customer service . . . . . . . . . . . . . . . .34

CW see Call waiting

Cable

ISDN connection cable . . . . . . . . . . . 6

Index

Internal

Calls. . . . . . . . . . . . . . . . . . . . . . . . 44

D channel . . . . . . . . . . . . . . . . . . . . . 43

Data modules . . . . . . . . . . . . . . . . . . 30

Defining the device type . . . . . . . . . . 29

De-register

Numbers . . . . . . . . . . . . . . . . . . . .19

Ringer . . . . . . . . . . . . . . . . . . . . . . 44

Users . . . . . . . . . . . . . . . . . . . . . . . 19

ISDN . . . . . . . . . . . . . . . . . . . . . . . . . 44

Abbreviations . . . . . . . . . . . . . . . . .44

Connection cable . . . . . . . . . . . . . . .6

Phone number, see MSN

Handset . . . . . . . . . . . . . . . . . . . . 14

Desktop unit (base). . . . . . . . . . . . . . . 4

Device type

Defining . . . . . . . . . . . . . . . . . . . . 29

Setting . . . . . . . . . . . . . . . . . . . . . 26

Devices

Telephone connection . . . . . . . . . . .4

Key

Connecting . . . . . . . . . . . . . . . . . . 26

Making calls with analogue

devices . . . . . . . . . . . . . . . . . . . . 28

Medical . . . . . . . . . . . . . . . . . . . . . . 3

Digital exchange . . . . . . . . . . . . . . . . 43

Direct call . . . . . . . . . . . . . . . . . . . . . 43

Paging . . . . . . . . . . . . . . . . . . . . . . 14

Keypad . . . . . . . . . . . . . . . . . . . . . . . 44

M101 Data . . . . . . . . . . . . . . . . . . . .30

Mains outlet . . . . . . . . . . . . . . . . . . . .4

Medical appliances. . . . . . . . . . . . . . . .3

Memos, see Answering Machine

Messages, see Answering Machine

Mini-Western connector . . . . . . . . . .6, 7

MSN . . . . . . . . . . . . . . . . . . . . . . 19, 44

Multiple subscriber number, see MSN

Music on hold . . . . . . . . . . . . . . . . . .44

Mute. . . . . . . . . . . . . . . . . . . . . . . . . 44

Electronic code lock . . . . . . . . . . . . . 43

Enquiry calls . . . . . . . . . . . . . . . . . . . 43

Entrance telephone. . . . . . . . . . . . . . 31

Exchange . . . . . . . . . . . . . . . . . . . . . 43

Features (handsets) . . . . . . . . . . . . . 15

Getting started . . . . . . . . . . . . . . . . . . 4

Getting started wizard. . . . . . . . . . . . . 8

Gigaset

Notebook function. . . . . . . . . . . . . . .45

Notes (spoken) see Memo

NTBA. . . . . . . . . . . . . . . . . . . . . . . 6, 45

M101 Data . . . . . . . . . . . . . . . . . . 30

Repeater . . . . . . . . . . . . . . . . . . . . 30

USB Adapter DECT/M105 . . . . . . . . 30

Open listening. . . . . . . . . . . . . . . . . .45

Outgoing MSN, freely selectable. . . . .45

Handset

De-register . . . . . . . . . . . . . . . . . . 14

Features . . . . . . . . . . . . . . . . . . . . 15

Paging. . . . . . . . . . . . . . . . . . . . . . 14

Handsfree. . . . . . . . . . . . . . . . . . . . . 43

Hold . . . . . . . . . . . . . . . . . . . . . . . . . 43

Pack contents . . . . . . . . . . . . . . . . . . .4

Paging. . . . . . . . . . . . . . . . . . . . . . . . 14

Paging key. . . . . . . . . . . . . . . . . . . . . 14

Parking . . . . . . . . . . . . . . . . . . . . . . . 45

Phonebook . . . . . . . . . . . . . . . . . . . .45

PIN . . . . . . . . . . . . . . . . . . . . . . . . 8, 45

Pl ugging to bus . . . . . . . . . . . . . . . . .45

Power failure . . . . . . . . . . . . . . . . . . . .6

Power supply cord . . . . . . . . . . . . . . . .6

Power supply unit . . . . . . . . . . . . . .3, 6

Installation

Base (mounting) . . . . . . . . . . . . . . . 4

Base (notes) . . . . . . . . . . . . . . . . 3, 4

Installation location (base) . . . . . . . . . 4

Index

Pre-dialling . . . . . . . . . . . . . . . . . 40, 45

Wall mounting (base) . . . . . . . . . . . . . .5

Questions and Answers . . . . . . . . . . . 33

Radio reception . . . . . . . . . . . . . . . . . . 4

Range. . . . . . . . . . . . . . . . . . . . . . 4 , 30

Remote activation . . . . . . . . . . . . . . . 46

Remote check . . . . . . . . . . . . . . . . . . 46

Remote delete, see Answering Machine

Repeater . . . . . . . . . . . . . . . . . . . 30, 46

Ring delay. . . . . . . . . . . . . . . . . . . . . 46

Bus . . . . . . . . . . . . . . . . . . . . . . . . 46

Jack. . . . . . . . . . . . . . . . . . . . . . . . . 6

Safety precautions. . . . . . . . . . . . . . . . 3

Service . . . . . . . . . . . . . . . . . . . . . . . 34

Setting

Base . . . . . . . . . . . . . . . . . . . . . . . . 8

Device type . . . . . . . . . . . . . . . . . . 26

Socket

TAE . . . . . . . . . . . . . . . . . . . . . . . . 36

Specifications . . . . . . . . . . . . . . . . . . 36

Standard connection . . . . . . . . . . . . . 46

System settings. . . . . . . . . . . . . . . . . 15

TAE. . . . . . . . . . . . . . . . . . . . . . . . . 6, 7

Connection . . . . . . . . . . . . . . . . . . 26

Socket . . . . . . . . . . . . . . . . . . . . . . 36

Telephone

Care . . . . . . . . . . . . . . . . . . . . . . . 33

Connecting . . . . . . . . . . . . . . . . . . 26

Three-party conference . . . . . . . . . . . 46

Toggling . . . . . . . . . . . . . . . . . . . . . . 46

Transfer . . . . . . . . . . . . . . . . . . . . . . 41

Two-way recording of phone calls . . . 46

USB Adapter DECT/M105 . . . . . . . . . . 30

USB cable . . . . . . . . . . . . . . . . . . . . . 30

Wait melody . . . . . . . . . . . . . . . . . . . 47

Wall holder . . . . . . . . . . . . . . . . . . . . . 4

Issued by

Information and Communication mobile

Haidenauplatz 1

D-81667 Munich

Right of modification reserved.

Printed in Germany (09/2003).

Siemens Aktiengesellschaft

http://www.my-siemens.com

No.: A31008-X255-B100-1-7619

Millennium Enterprises Air Conditioner Z42 User Manual
Panasonic Cu A9ckp5 User Manual
Philips 32pw9551 User Manual
Roper Air Conditioner User Manual
Samsung Sh07zpgax User Manual
Soleus Air Ky 34 User Manual
Spt Wa 8011s User Manual
Tyco Flash Charge 92136 0920 User Manual
Xerox Workcentre Pro 255 User Manual
Zenoah G240rc User Manual