Sharp Ar 164 User Manual

MODEL

AR-164

DIGITAL LASER

COPIER/PRINTER

OPERATION MANUAL

Page

• GETTING STARTED

• MAKING COPIES

• SPECIAL FEATURES

• STATUS INDICATORS

• GENERAL INFORMATION 46

• OPTIONAL EQUIPMENT 65

CONTENTS

Page

GETTING STARTED

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . 4

– Overall layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

– Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

COPIER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CAUTIONS ON HANDLING . . . . . . . . . . . . . . . . . . . . . . . . 9

LOADING COPY PAPER . . . . . . . . . . . . . . . . . . . . . . 10

MAKING COPIES

AUDITING ACCOUNTS . . . . . . . . . . . . . . . . . . . . . . . . . . 13

NORMAL COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

– Using the SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

– Using the original table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

REDUCTION/ENLARGEMENT/ZOOM . . . . . . . . . . . . . . . 18

BYPASS FEED (special paper) . . . . . . . . . . . . . . . . . . . . 20

TWO-SIDED COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . 22

SORT/GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

INTERRUPTING A COPY RUN . . . . . . . . . . . . . . . . . . . . 25

AUTOMATIC EXPOSURE ADJUSTMENT . . . . . . . . . . . . 26

TONER SAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

SPECIAL FEATURES

XY ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

B/W REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

DUAL PAGE COPY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

ROTATION COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

2 IN 1 OR 4 IN 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

ERASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

MARGIN SHIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

STATUS INDICATORS

TONER CARTRIDGE REPLACEMENT . . . . . . . . . . 38

MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . 40

DEVELOPER REQUIRED . . . . . . . . . . . . . . . . . . . . . 45

MAINTENANCE REQUIRED . . . . . . . . . . . . . . . . . . . 45

GENERAL INFORMATION

USER PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

– Settings for auditing accounts . . . . . . . . . . . . . . . . . . . . . . 49

POWER SAVE MODES . . . . . . . . . . . . . . . . . . . . . . . . . . 53

USER MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

COPIER TROUBLE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

SUPPLIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

– Types and sizes of copy paper . . . . . . . . . . . . . . . . . . . . . . 60

– Genuine supplies statement . . . . . . . . . . . . . . . . . . . . . . . . 61

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

OPTIONAL EQUIPMENT

SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . 66

250-SHEET PAPER FEED UNIT (AR-DE5)/

2x250-SHEET PAPER FEED UNIT (AR-DE6) . . . . . . . . . 67

INDEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

INTRODUCTION

This copier has been designed to provide convenient copying features in a minimum

amount of office space and with maximum operational ease. To get full use of all copier

features, be sure to familiarize yourself with this manual and the copier.

For quick reference during copier use, keep this manual in a handy location.

This copier can be used as a laser printer and as a facsimile machine by installing optional

components.However, this manual describes only the copier features.For description of the printer

features and facsimile features, see their separate manuals.

Conventions used in this manual

In this manual, the following icons are used to provide the user with

information pertinent to the use of the copier.

Warns the user that injury to the user or damage to the

copier may result if the contents of the warning are not

properly followed.

Cautions the user that damage to the copier or one of its

components may result if the contents of the caution are

not properly followed.

Notes provide information relevant to the copier regarding

specifications, functions, performance, operation and such,

that may be useful to the user.

Indicates a letter displayed in the copy quantity display.

MAIN FEATURES

High-speed laser copying

First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on).

Copying speed is 16 copies/min., which adapts to business use, allowing improvement of working efficiency.

High-quality digital image

High-quality copying at 600 dpi is performed.

In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.

The photo mode copying function allows clear copying of delicate halftone original images such as monochrome

photos and color photos. Photo mode is adjustable in five steps.

Substantial copying features

Copies up to ledger size originals from the original table, or through the 30 sheet automatic document feeder

Zoom copying from 50% to 200% in 1% increments can be performed.

Continuous copying of maximum 99 sheets can also be performed.

Scan once/print many to increase reliability and productivity

Electronic sorting eliminates the need for a bulky, mechanical sorter

Dual page copy mode for books, magazines and manuals

Editing features like XY zoom and black/white reverse

Digital editing features like 2 IN 1/4 IN 1 copying

Toner save mode reduces toner consumption by approximately 10%.

User programs allow setting/modification of functions for customer needs. Also the user programs allow the internal

auditor to be controlled.

Optional features

This copier can be used as a laser printer by installing an optional printer expansion kit.

This copier can be used as a facsimile machine by installing an optional facsimile expansion kit.

Environmentally friendly design

Paper output tray is housed in the copier for space saving.

Preheat and auto power shut-off modes are provided to reduce power consumption in standby mode and meet the

Energy Star Guidelines.

As an ENERGY STAR^®Partner, SHARP has determined that this product meets the

ENERGY STAR^®guidelines for energy efficiency.

PART NAMES AND FUNCTIONS

Overall layout

Document feeder cover

Paper tray

Open to make copies from the original table.

Holds 250 sheets of copy paper.

Original table

Side cover

All originals which cannot be copied from the SPF must

Open to remove misfeeds and to service the copier.

be copied here.

Side cover handle

Handles

Lift and pull to open the side cover.

Use to move the copier.

Bypass tray guides

Power switch

Adjust to the width of the copy paper.

Press to turn copier power on and off.

Bypass tray

Operation panel

Paper including special paper (such as transparency

All copier controls are located here for easy operation.

film) can be fed from the bypass tray.

Paper output tray

Bypass tray extension

Finished copies are deposited in the paper output tray.

Pull out when feeding large paper such as 8-1/2" x 14"

and 11" x 17".

Front cover

Open to remove misfeeds and for copier servicing.

Charger cleaner

Use to clean the transfer charger.

PART NAMES AND FUNCTIONS

Single pass feeder (SPF)

Document feeder tray

Fusing unit release levers

Holds up to 30 originals.

Lower to remove misfed paper.

Original guides

Adjust to the size of the originals.

The fusing unit is hot.

Take care in removing paper.

Feeding roller cover

Open to remove misfed originals.

Right side cover

Open to remove misfed originals.

Exit area

Finished originals are output here.

Paper guide

Open to remove misfed paper.

Toner cartridge lock release lever

Use to unlock the toner cartridge.

Accessories

Toner cartridge

Contains toner.

Operation manual . . . . . . . . . . . . . . . . . . . . . . 1

Charger cleaner . . . . . . . . . . . . . . . . . . . . . . . . 1

Photoconductive drum

Copy images are formed on the photoconductive drum.

Roller rotating knob

Turn to remove misfed paper.

PART NAMES AND FUNCTIONS

Operation

panel

INTERRUPT key and indicator (p. 25)

Interrupts a copy run.

Output tray full indicator (p. 23)

Indicatescopiesmustberemovedfromthepaperoutput

tray.

Copy quantity display

Displays the specified copy quantity during the ready

B/W REVERSE key and indicator (p. 30)

condition and displays the copy countdown as copies

Press to reverse the black and white areas.

are made. Also see items and

XY-ZOOM key and indicator (p. 28)

Press to change the horizontal and vertical copy ratios

independently.

ZOOM indicator (p.19)

Lights up when a zoom ratio is set.

Copy ratio display key (p. 19)

SORT/GROUP key and indicators (p. 23)

Press and hold down during standby to display the copy

ratio in the copy quantity display.

Press to select the sort or group mode.

ORIGINAL DATA indicator

Blinks when the memory becomes full of scanned

original image data.

Zoom keys (p. 19)

Use to select any reduction or enlargement copy ratio

from 50% to 200% in 1% increments.

2 IN 1 / 4 IN 1 key and indicators (p. 33)

Press to select the 2 in 1 or 4 in 1 mode.

PAPER SIZE ENTER key (p.12)

Use to set the paper size in a paper tray.

AUTO/MANUAL/PHOTO key and indicators

(p. 15)

AUDIT CLEAR key (p.13)

Closes an open account.

Use to sequentially select the exposure modes: AUTO,

MANUAL, or PHOTO.

PAPER SIZE indicators

Light up to show the selected copy paper size.

Light and dark keys and indicators (p. 15)

Use to adjust the MANUAL or PHOTO exposure level.

Alarm indicators

: Maintenance indicator (p. 45)

: Toner cartridge replacement required indicator

(p. 38)

Numeric keys

Use to select the desired copy quantity or to make user

program entries.

: Developer replacement required indicator

(p. 45)

: Paper required indicator (p.10)

: Misfeed indicator (p. 40)

Zero key

Use as part of numeric keys to enter copy quantity.

Press during a continuous copy run to display the

number of copies completed in the current run.

Press and hold during standby to display the total output

count.

POWER SAVE indicator (p. 53)

Lights up when the copier is in a power save mode.

SPF indicator (p. 14)

Lights up when originals are set in the document feeder

tray.

PART NAMES AND FUNCTIONS

1st display

2nd display

Paper feed location/misfeed location indica-

tors (p. 40)

The selected paper feed location is shown by a lit

indicator ( ).

The general location of misfed paper is shown by a

Press and hold down the key.

12,345

sheets output

blinking red indicator (

Note: 11" x 17" size copies are counted as two

DUAL PAGE COPY key and indicator (p. 31)

Use to make individual copies of two originals placed

side by side on the original table.

copies.

CLEAR key

Clears the copy quantity display or terminates a copy

run.

ERASE key and indicators (p. 35)

Press to select the edge erase and/or the center erase

mode.

START key and indicator

Copying is possible when the indicator is on.

Press to start copying.

MARGIN SHIFT key and indicator (p. 37)

Shifts text or image on the copy to leave a binding

margin on the left side of the copy.

CLEAR ALL ( ) key

Clears all selected settings and returns the copier to the

initial settings.

PRESET RATIO selector keys and indicators

(p. 19)

Use to sequentially select preset reduction/enlargement

copyratios:50%, 64%, 77%, 95%, 100%, 121%, 129%,

141%, 200%.

Initial settings

The copier assumes the initial settings when it is first turned

on, when the CLEAR ALL ( ) key is pressed, and ap-

proximately one minute* after the last copy is made in any

mode.

ORIGINAL SIZE ENTER key and indicators

(p.16, 18)

Use to input the original size for automatic paper

selection and automatic copy ratio selection.

Copy ratio: 100%

Exposure: Automatic

Copy quantity: 0

All special copier modes: Off

Auto paper selection: On

Paper feed station: Previously selected paper tray

AUTO PAPER SELECT indicator

Paper of the proper size will be automatically selected

depending on the original size and selected copy ratio

when this indicator is on.

* This time (auto clear time) can be changed. See page 46,

USER PROGRAMS.

TRAY SELECT key (p. 16)

Use to manually select a paper tray.

AUTO IMAGE key and indicator

Press for automatic copy ratio selection.

COPIER INSTALLATION

Improper installation may damage the copier. Please note the following

during initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier.

Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room

temperature for at least 2 hours before use.

Do not install your copier in areas that are:

damp, humid, or very dusty

exposed to direct sunlight

poorly ventilated

subject to extreme temperature or humidity changes, e.g., near an

air conditioner or heater.

The copier should be installed near an accessible power outlet

for easy connection.

Be sure to connect the power cord only to a power outlet that

meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

Connect the copier to a power outlet which is not used

for other electric appliances. If a lighting fixture is

connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for

servicing and proper ventilation.

4" (10 cm)

A small amount of ozone is produced within the copier during operation.The emission level is insufficient

to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m³) calculated as an

8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it is advisable to

place the copier in a ventilated area.

CAUTIONS ON HANDLING

Be careful in handling the copier as follows to maintain the performance of

this copier.

Do not drop the copier, subject it to shock or strike it against any

object.

Storesparetonercartridgesinacooldryplacewithoutremoving

from the package before use.

If they are exposed to direct sunlight or excessive heat, poor copies

may result.

Do not touch the photoconductive drum (green portion).

Scratches or smudges on the drum will cause dirty copies.

LOADING COPY PAPER

Tosavespace, thiscopierhasbeendesignedwithanadjustablefront-loading

tray, which is easily opened for paper loading. For best results, use only

SHARP recommended paper. (See page 60.)

The paper required ( ) indicator will light up when there is no copy paper

in the selected paper feed station, or when the selected paper tray is not

installed or is improperly installed.

When the paper size is changed in a paper tray, the size

of the paper must be entered by steps 8 through 11 on

page 12.If not, the edges of copies may become smudged

with toner.Also, the AUTO PAPER SELECT and the AUTO

IMAGE features will not function properly.

Gently lift and pull out the paper tray until it stops.

Push the pressure plate down until it locks in place.

Fan the copy paper and insert it into the tray. Make sure

the edges go under the corner hooks.

If you change to a different size of copy paper, the tray must be

adjusted. See the next page.

Set the paper along the guides.

Maximum height line

The tray holds up to 250 sheets of 21 lb. bond paper.

Do not load paper above the maximum height line.

Push the paper tray firmly back into the copier.

LOADING COPY PAPER

Changing the copy paper size in the tray

Gently lift and pull out the paper tray until it stops.

Push the pressure plate down until it locks in place.

Squeeze the lock lever of the front guide and slide the

front guide to match the width of the paper.

Left guide

Move the left guide to the appropriate slot as marked

on the tray.

When using 5-1/2" x 8-1/2" copy paper, load it into the uppermost

paper tray. If other trays (in optional paper feed units) are used, paper

misfeeds may occur.

Front guide

When using 11" x 17" copy paper, store the left guide in the slot at

the left front of the paper tray.

Load copy paper into the tray.

Place the appropriate label to indicate the selected

paper size into the recess on the right front side of the

paper tray.

Push the paper tray firmly back into the copier.

LOADING COPY PAPER

To set the selected paper size, press the PAPER SIZE

ENTER key.

The selected paper feed location indicator will blink and the

corresponding paper size (which is currently set) indicator will light

up steadily. All other indicators except the START key indicator will

go out.

For paper size setting, ensure that the COPY mode

has been selected. However, if copying, printing or

facsimile printing is being performed, paper size setting

cannot be made even in the COPY mode. See Note

on page 58.

Use the TRAY SELECT key to select the paper tray of

which the paper size has been changed.

Each time the TRAY SELECT key is pressed, a paper tray will be

indicated with a blinking paper feed location indicator. If an optional

paper feed unit is not installed, this operation is not needed.

Use the ORIGINAL SIZE ENTER key to select the paper

size which is set.

Each time the ORIGINAL SIZE ENTER key is pressed, a paper size

will be indicated with a paper size indicator.

Press the START key and then the PAPER SIZE ENTER

key.

To change the paper size setting of another tray, repeat steps 9 to 10

after pressing the START key.

AUDITING ACCOUNTS

If this copier has been programmed in the auditing mode, it will not function

until an assigned 3-digit account number has been entered. See page 49 for

setting the auditing mode.

If the copier has been programmed in the auditing mode, “–––” will appear

in the copy quantity display in the initial conditions.

Enter your account number using the numeric keys.

As each digit is entered, the dashes in the copy quantity display will

disappear.

After the number is entered, the copy quantity display will change to

If an unassigned number is entered, “–––” will appear again in the

copy quantity display, indicating that the number was not accepted.

When copying is completed, press the AUDIT CLEAR

key.

“–––” will appear again in the copy quantity display, indicating the

auditing mode.

In the interrupt copy mode (see page 25), press the INTERRUPT key

after an interrupt copy run is completed. All previous copier settings

will be restored and the previous account number will be active.

NORMAL COPYING

Using the SPF

This copier has two document input stations –– a single pass

feeder (SPF) for automatic document feeding and an

original table for manual handling of bound documents.

The SPF is designed to hold up to 30 originals measuring

from 5-1/2" x 8-1/2" to 11" x 17" and in the weight range of

15 to 24 lbs.

Beforeplacingcurledorwavyoriginalsintothedocument

feedertray,besuretoflattenthem.Ifnot,originalmisfeeds

may result.

For best feeding of originals which have binding holes

punched into them, insert them so that the holes are

positioned to the right or along the side guides.

Special originals such as transparency film and tracing

paper should not be fed through the SPF but should be

copied from the original table.

Be sure to remove any staples or paper clips from the

originals.

Damaged or crumpled originals may misfeed in the SPF.

It is recommended that these originals be copied from the

original table.

Stream feeding mode

If the stream feeding mode has been enabled using user program

No. 4, the SPF indicator will continue to blink for approximately

5 seconds after feeding of all originals is completed. While this

indicator is blinking, any new originals placed in the SPF will be

fedandcopiedautomatically.Seepage46,USERPROGRAMS.

Turn the power switch on.

It will take about 35 seconds for the copier to warm up. However, you

can make desired settings and press the START key during warm-up.

Copying will start after warm-up.

Power on

If the copier has been programmed in the auditing mode, the START

key indicator will not light up and “–––” will appear in the copy

quantity display. Enter an assigned 3-digit account number. See page

13.

If the power is already on and all indicators except the POWER SAVE

indicator are off, the copier is in the auto power shut-off mode. Press

the START key in this case. See page 53, POWER SAVE MODES.

Ensure that no original is left on the original table.

Adjust the original guides to the size of the originals.

Set the originals face up in the document feeder tray.

The SPF indicator will light up. If this indicator does not light up, the

originals are not properly set or the SPF is not properly closed.

Ensure that the copy paper size in the paper tray is the

same size as the originals.

If an optional paper feed unit is installed, a paper tray with the

corresponding paper size will be automatically selected.

NORMAL COPYING

Adjust the copy density.

Thiscopierhasthreeexposuremodestochoosefrom—AUTOMATIC,

MANUAL, and PHOTO.

Automaticexposureisthestandardinitialsettingforthiscopier.Inthis

mode, the characteristics of the original are “read” by the exposure

system and adjustments are automatically made. This optimizes the

contrast of the copied images by reducing the effect of colored or

shadedbackgroundareas.Seepage26toadjusttheautomaticexposure

level.

For manual copy density adjustment, press the AUTO/MANUAL/

PHOTO key to select MANUAL and adjust with the light ( ) and

dark ( ) keys as desired.

For photographs, select PHOTO and then adjust with the light (

and dark ( ) keys as desired.

)

There are 5 exposure steps indicated by 3 indicator lights. (The

indicators light up one or two at a time.)

Ifexposurelevel2isselected,thetwoleft-handmostindicatorsforthat

level will light up simultaneously. Also, if level 4 is selected, the two

right-handmost indicators for that level will light up simultaneously.

Set the number of copies using the numeric keys.

A single copy can be made with the initial setting, i.e., when “0” is

displayed.

Press the CLEAR ( ) key to clear an entry if a mistake is made.

Press the START key.

The number in the copy quantity display will decrease by 1 each time

a copy is made.

Press the CLEAR key to stop copying in the middle of a run.

If the paper in the selected tray runs out during the copy run and no

other tray contains the same size paper, the bypass tray can be selected

using the TRAY SELECT key.

While making copies from the SPF, do not place

originals of the next copying job. Place them after all

copies of the current job have been output.

NORMAL COPYING

Using the original table

Turn the power switch on.

It will take about 35 seconds for the copier to warm up. However, you

can make desired settings and press the START key during warm-up.

Copying will start after warm-up.

Power on

If the copier has been programmed in the auditing mode, the START

key indicator will not light up and “–––” will appear in the copy

quantity display. Enter an assigned 3-digit account number. See page

13.

If the power is already on and all indicators except the POWER SAVE

indicator are off, the copier is in the auto power shut-off mode. Press

the START key in this case. See page 53, POWER SAVE MODES.

Place the original face down on the original table. Align

it with the original size scale.

Image loss (max. 5/32" (4 mm)) can occur at the leading and trailing

edges of the copies. Also image loss (max. 5/32" (4 mm) in total) can

occur along the other edges of the copies.

Close the platen cover.

Ensure that the copy paper size in the paper tray is the

same size as the original.

If a tray of the required size is not installed, use the bypass tray and

press the TRAY SELECT key to select the bypass tray.

If an optional paper feed unit is installed:

UsetheORIGINALSIZEENTERkeytoselecttheoriginalsize.Copy

paper of the same size as the original will be automatically selected.

If desired, another paper tray can be selected by pressing the TRAY

SELECT key.

Adjust the copy density.

Thiscopierhasthreeexposuremodestochoosefrom—AUTOMATIC,

MANUAL, and PHOTO.

Automaticexposureisthestandardinitialsettingforthiscopier.Inthis

mode, the characteristics of the original are “read” by the exposure

system and adjustments are automatically made. This optimizes the

contrast of the copied images by reducing the effect of colored or

shadedbackgroundareas.Seepage26toadjusttheautomaticexposure

level.

NORMAL COPYING

For manual copy density adjustment, press the AUTO/MANUAL/

PHOTO key to select MANUAL and adjust with the light ( ) and

dark ( ) keys as desired.

For photographs, select PHOTO and then adjust with the light (

and dark ( ) keys as desired.

)

There are 5 exposure steps indicated by 3 indicator lights. (The

indicators light up one or two at a time.)

Ifexposurelevel2isselected,thetwoleft-handmostindicatorsforthat

level will light up simultaneously. Also, if level 4 is selected, the two

right-handmost indicators for that level will light up simultaneously.

Set the number of copies using the numeric keys.

A single copy can be made with the initial setting, i.e., when “0” is

displayed.

Press the CLEAR ( ) key to clear an entry if a mistake is made.

Press the START key.

The number in the copy quantity display will decrease by 1 each time

a copy is made.

Press the CLEAR key to stop copying in the middle of a run.

To repeat the same copy sequence for a different original, simply

replace the original and press the START key.

If the paper in the selected tray runs out during the copy run and no

other tray contains the same size paper, the bypass tray can be selected

using the TRAY SELECT key.

REDUCTION/ENLARGEMENT/ZOOM

Reduction and enlargement ratios can be selected either automatically with

the AUTO IMAGE key or manually with the PRESET RATIO selector (

)keysand/orthezoom( )keys.Thezoomfunctionenablesprecise

copy ratio selection from 50% to 200% in 1% increments.

Automatic

Place the original in the document feeder tray or on the

original table.

When using the original table, press the ORIGINAL SIZE

ENTER key until the indicator for the size of the original

on the original table lights up.

Use the TRAY SELECT key to select the paper tray with

the desired paper size.

This feature will not work when copy paper of non-standard size is

used or the bypass tray is used.

Press the AUTO IMAGE key.

The copy ratio will be automatically set.

If a PRESET RATIO indicator is blinking, part of the original image

may not be copied.

If user program No.7 is not set and the orientation of

theoriginaldoesnotcorrespondtostandardreduction/

enlargement ratios for the selected paper tray, the

ORIGINAL SIZE indicator will blink. Change the

orientation of the original.

Set the number of copies.

Press the START key.

To cancel the automatic reduction/enlargement

mode, press the AUTO IMAGE key again.

When copying from the SPF with this feature, the

automatic reduction/enlargement mode will be

automatically canceled after copying is complete.

REDUCTION/ENLARGEMENT/ZOOM

Manual

Place the original in the document feeder tray or on the

original table.

Use the PRESET RATIO selector (

) keys and the

zoom (

) keys to select the desired copy ratio.

To select a preset reduction or enlargement copy ratio, press the

key repeatedly until the indicator for the desired copy ratio is

lit.

A. Preset reduction ratios are: 95%, 77%, 64%, and 50% .

B. Preset enlargement ratios are: 121%, 129%, 141%, and 200%.

C. Zoom ratios: Any ratio from 50% to 200% can be set, in 1%

increments. Press the

ratio, then press the

to increase the ratio.

key to set the approximate

key to decrease the ratio or the key

When a zoom (

) key is pressed, the ZOOM indicator will light

up and the zoom ratio will be displayed in the copy quantity display

for at least two seconds.

To verify a zoom setting without changing the zoom ratio, press and

hold down the copy ratio display ( ) key. When the key is released,

the display will return to the copy quantity display.

To decrease or increase the zoom ratio rapidly, press and hold down

the

key. However the value will stop at the preset reduction

or enlargement ratios. To move beyond these ratios, release the key

and then press and hold it down again.

D. Same-size reset: Press the

copy ratio returns to 100%.

key repeatedly until the

Ensure that copy paper of the desired size is installed in

the paper tray.

If an optional paper feed unit is installed:

UsetheORIGINALSIZEENTERkeytoselecttheoriginalsize.Copy

paper of the appropriate paper size will be automatically selected

based on the original size and copy ratio. If the selected PRESET

RATIO indicator or the ZOOM indicator blinks, the selected copy

image is too large for the copy paper size.

The desired paper tray can also be selected by pressing the TRAY

SELECT key.

Set the number of copies and press the START key.

BYPASS FEED (special paper)

The bypass tray is used to copy onto transparency film, labels, and other

special purpose papers. Up to 100 sheets of standard copy paper can be set

in the bypass tray.

For special purpose papers, the original image must be

smaller than the paper or media for copying.

Iftheoriginalimageisbiggerthanthepaperormedia,this

may cause smudges on the edges of the copies.

Alsoforstandardcopypaper, smudgesmayappearifthe

copy paper is not at least as large as the original image.

Unfold the bypass tray.

When feeding 8-1/2" x 14" or 11" x 17" sized paper, extend the feeder

tray.

Set the paper guides to the copy paper width.

Insert the copy paper (print face down) all the way into

the bypass tray.

Up to 100 sheets of standard copy paper measuring from 5-1/2" x

8-1/2" to 11" x 17" can be loaded in the bypass tray.

Transparency film, labels, and other special purpose papers (except

envelopes) must be fed individually.

Up to 10 envelopes can be set.

Whenaddingpaper, firstremoveremainingpaper, combineitwiththe

paper to be added and then reload as a single stack.

When loading envelopes, make sure that they are straight and flat.

BYPASS FEED (special paper)

Press the TRAY SELECT key to select the bypass tray.

Leave the copy quantity at 0 if using special papers. Set

the number of copies if using standard copy paper or

envelopes.

Press the START key.

TWO-SIDED COPYING

Two-sided copies can be made on this copier using the bypass tray.

Place the first original on the original table and make a

copy.

The first copy can be made using any of the paper feed stations.

Replace the first original with the second original and

close the platen cover.

Make sure that the first and second originals are oriented in the same

way on the original table.

Whentheoriginalsareplacedhorizontally, makesurethatthefirstand

second originals are oriented in the reverse way on the original table.

The first and second originals can be set in the document feeder tray.

However they must be set individually.

Turn the first copy over left to right and place it into the

bypass tray.

Be sure to feed the copies one sheet at a time.

Use the TRAY SELECT key to select the bypass tray.

Press the START key.

SORT/GROUP

This copier has two sorter modes for different copying jobs: one sorts copies into sets

matching the sequence of the originals and the second groups copies by originals.

The sort/group feature cannot be used with the dual page copy feature.

To change the SORT/GROUP mode, press the SORT/GROUP key to select the desired

mode.

Thecapacityofthepaperoutputtrayis250sheets(150sheetsifanoptionaljobseparator

tray kit (AR-TR2) is installed). When the number of copies output reaches this limit in

a sort or a group copy run, copying will stop, the output tray full (

and the START key indicator will blink.

) indicator will light

Remove the copies from the paper output tray and press the START key to resume

copying.

Sort mode

Each set of copies will be sequentially delivered to the

paper output tray.

Group mode

All copies of the same originals will be grouped in the

paper output tray.

Offset stack

Offset mode

If the offset stack mode is enabled using user program

No. 19, each copy will be offset by approximately 1 inch

(25 mm). When copying in the sort mode, each collated

set of copies will be stacked offset from the previous

set. When copying in the group mode, copies will be

offset and stacked in groups of multiple copies from the

same original.

If the offset stack mode is disabled, copies will not be

offset.

The offset stack mode is enabled in the factory default

setting.

Non-offset mode

SORT/GROUP

Copying in the sort mode

Whencopyinginthesortmode,theoriginalimagewillbestoredinthecopier

memory each time an original is scanned and copying will start after all

originals have been scanned.

Set the originals face up in the document feeder tray.

The original table cannot be used for sort copying.

Press the SORT/GROUP key to select the SORT mode.

Ensure that the copy paper size in the paper tray is the

same size as the originals.

If an optional paper feed unit is installed, a paper tray with the

corresponding paper size will be automatically selected.

Set the number of copies and press the START key.

Copying will start after the originals have been scanned. Up to 30

sheets of originals can be scanned. (If originals are fed continuously

using the stream feeding mode, up to approximately 60 sheets of 8-1/

2" x 11" originals can be scanned. However,when copying originals

which require more memory such as photographs, the number of

originals which can be scanned will be less.) When the memory

becomes full of scanned original image data, the ORIGINAL DATA

indicator will blink.

When the ORIGINAL DATA indicator blinks, the copier will stop

scanning. Tostartcopyingofscannedoriginals, presstheSTARTkey.

To cancel copying, press the CLEAR or CLEAR ALL key.

INTERRUPTING A COPY RUN

INTERRUPT is used to interrupt a long copy run so that another job can be

done.

SORT or GROUP cannot be selected during interrupt copying.

Press the INTERRUPT key.

The copier will return to the initial settings.

If this copier has been programmed in the auditing mode using user

programNo.10,“–––”willappearinthecopyquantitydisplay.Enter

your account number using the numeric keys. The number of copies

of the interrupt copying will be accumulated against this account

number. See page 13.

When the SPF is being used, the copier will stop after completing the

copying of the original which has been fed into the SPF.

When the copier stops, remove the original(s) and set

the original(s) for interrupt copying.

Select the desired available copier functions.

Set the number of copies.

Press the START key.

The interrupt copies will be offset from the previous copies when user

program No. 19 is enabled. See page 46.

When all INTERRUPT copies are finished, press the

INTERRUPT key again to cancel the INTERRUPT mode,

and remove the original used for interrupt copying.

The previous copy quantity, copy ratio, copy density, and paper size

will be automatically restored.

Replacetheoriginalfortheinterruptedjobandpressthe

START key to resume copying.

AUTOMATIC EXPOSURE ADJUSTMENT

The automatic exposure level can be adjusted to suit your copying needs.

This level is set for copying from the original table and copying from the

SPF respectively. To set the level for the SPF, place an original in the

document feeder tray and make sure that the SPF indicator lights up before

proceeding to step 1. To set the level for the original table, ensure that the

SPF indicator d2oes not light up.

Press the AUTO/MANUAL/PHOTO key to select the

PHOTO mode.

Press and hold down the AUTO/MANUAL/PHOTO key

for approximately 5 seconds.

The PHOTO indicator will go out and the AUTO indicator will begin

to blink.

One or two exposure indicators corresponding to the current auto-

matic exposure level will light up. The factory default setting is level

“3”.

Press the light ( ) or dark( ) key to lighten or darken

the automatic exposure level as desired.

Press the AUTO/MANUAL/PHOTO key.

The AUTO indicator will stop blinking and will light up steadily.

This automatic exposure level will remain in effect until you change

it again by this procedure.

TONER SAVE MODE

Thismodereducestonerconsumptionbyapproximately10%intheautomatic

and manual exposure modes. Copies will be lighter but still adequate for

generaluse. SelectionofthismodedoesnotaffectthePHOTOmode. Follow

the procedure below for setting the toning level.

Press the AUTO/MANUAL/PHOTO key to select the

MANUAL mode.

Press and hold down the AUTO/MANUAL/PHOTO key

for approximately 5 seconds.

The MANUAL indicator will go out and the PHOTO indicator will

begin to blink.

The exposure indicator marked “5” will light up, indicating that the

standard toner mode is active.

To enter the toner save mode, press the light ( ) key.

The exposure indicator marked “1” will light up, indicating that the

toner save mode is selected.

Press the AUTO/MANUAL/PHOTO key.

ThePHOTOindicatorwillstopblinkingandwilllightupsteadily.The

toner save mode is now active.

To return to the standard mode, repeat the procedure but use the dark

(

) key to select exposure level “5” in step 3.

XY ZOOM

The XY ZOOM feature allows the horizontal and vertical copy ratios to be

changed independently. This feature cannot be used with the 2 in 1 or 4 in 1

feature.

Original

Copy

To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the

DUAL PAGE COPY feature first and then the XY ZOOM feature.

(Enlargement cannot be set.)

Place the original in the document feeder tray or on the

original table.

Press the XY-ZOOM key.

The current value for the vertical direction will be displayed in the

copy quantity display.

UsethePRESETRATIOselector(

(

direction.

)keysandzoom

) keys to change the copy ratio in the vertical

PressaPRESETRATIOselector(

)keytosetanapproximate

ratio, then press the

key to decrease the ratio or key to increase

the ratio. The copy ratio will be displayed in the copy quantity display.

Press the copy ratio display ( ) key.

The selected ratio for the vertical direction will be entered and the

current value for the horizontal direction will be displayed in the copy

quantity display.

XY ZOOM

UsethePRESETRATIOselector(

)keysandzoom

(

) keys to change the copy ratio in the horizontal

directioninasimilarmannerasfortheverticaldirection.

Press the copy ratio display ( ) key.

The selected ratio for the horizontal direction will be entered and the

display will change to the copy quantity display.

To verify the copy ratios, press and hold down the copy ratio display

(

)key.Theverticalandhorizontalratioswillbealternatelydisplayed.

Ensure that copy paper of the desired size is installed in

the paper tray.

If an optional paper feed unit is installed:

When copying from the original table, use the ORIGINAL SIZE

ENTER key to select the original size. Copy paper of the appropriate

papersizewillbeautomaticallyselectedbasedontheoriginalsizeand

copy ratios. If desired, another paper tray can be selected by pressing

the TRAY SELECT key.

Set the number of copies.

Press the START key.

To change the copy ratios again, press a PRESET

RATIO selector (

) key or a zoom (

)

key. Then, perform step 3 and the succeeding

steps.

To cancel this function, press the XY-ZOOM key

again.

B/W REVERSE

The B/W REVERSE feature is used to reverse black and white areas.

Original

Copy

When the B/W REVERSE feature is selected, the exposure mode will be

automatically set to the MANUAL mode. Other exposure modes cannot

be selected.

Evenifthisfeatureiscanceled,theMANUALmodewillnotautomatically

be canceled.

Place the original in the document feeder tray or on the

original table.

Press the B/W REVERSE key.

Check the copy paper size.

If an optional paper feed unit is installed:

When copying from the original table, use the ORIGINAL SIZE

ENTER key to select the original size. Copy paper of the same size as

the original will be automatically selected. If desired, another paper

tray can be selected by pressing the TRAY SELECT key.

Make all other desired copier selections and press the

START key.

DUAL PAGE COPY

Original

Copy

TheDUALPAGECOPYfeatureproducesindividualcopiesoftwodocuments

placed side by side on the original table. It is especially useful when copying

books and other bound documents. This feature cannot be used with the 2 in

1 or 4 in 1 feature and sort/group feature. If the AUTO IMAGE feature has

been selected, this feature cannot be selected.

To use the DUAL PAGE COPY feature with the XY ZOOM feature, set the

DUAL PAGE COPY feature first and then the XY ZOOM feature.

(Enlargement cannot be set.)

Place the originals on the original table with the center

of the two pages aligned with the paper size index (

8¹/2 ). Close the platen cover.

Set the page to be copied first to the right of the paper size index mark.

Press the DUAL PAGE COPY key.

Check to be sure that the copy paper size in the paper tray is

8-1/2" x 11".

Set the number of copies.

Press the START key.

ROTATION COPYING

If user program No. 7 is set, the image of the original will rotate when the

orientation of the original does not match that of the copy paper. Rotation

copying will function only if the AUTO PAPER SELECT mode or AUTO

IMAGE mode has been selected. Even if user program No. 7 is not set,

rotation copying will function when the 2 in 1 or 4 in 1 function is selected.

See page 46. However, if enlargement copying onto a paper size larger than

8-1/2" x 11" is performed, the image cannot be rotated.

Original

Paper

When this occurs, the detected size and orientation of the original will be

indicatedbyasteadilylightedindicatorandaflashingindicatorwillshowthe

requiredorientationoftheoriginal. Theoriginalmustberotated90°tomatch

the flashing indicator to prevent image loss on the copies.

Copy

Example: Copying from an 11" x 17"

original onto 8-1/2" x 11" paper

2 IN 1 OR 4 IN 1

The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a

specified order, onto one sheet.

2 in 1 copying

These features cannot be used with the dual page copying, XY zoom, erase,

or margin shift features.

Copies can be made with or without the border lines shown in the illustration.

See user program No.6 on page 46.

The order of originals which will be arranged on the copies can be selected by

user programs. There are two patterns of layout for 2 in 1 copying and four

patterns of layout for 4 in 1 copying. See user program No.17 and No.18 on

page 46.

The 2 in 1 or 4 in 1 feature operates only in the sort or group mode. If the 2 in

1 or 4 in 1 feature is selected when either the sort or group mode has not been

selected, the group mode will be automatically selected.

4 in 1 copying

Set the originals face up in the document feeder tray.

The original table cannot be used for the 2 in 1 or 4 in 1 feature.

Use the TRAY SELECT key to select the paper tray with

the desired paper size.

The bypass tray and any tray with non-standard size paper cannot be

used with the 2 in 1 or 4 in 1 feature.

To confirm or set the layout pattern for 2 in 1 copying,

first ensure that both the 2 IN 1 and 4 IN 1 indicators are

not lit then press and hold the 2 IN 1 / 4 IN 1 key for more

than 5 seconds.

The2IN1indicatorwillblinkandthecurrentlyselectedlayoutpattern

number will blink in the copy quantity display.

To confirm or set the layout pattern for 4 in 1 copying,

use the 2 IN 1 / 4 IN 1 key to light the 2 IN 1 indicator then

press and hold the 2 IN 1 / 4 IN 1 key for more than 5

seconds.

The4IN1indicatorwillblinkandthecurrentlyselectedlayoutpattern

number will blink in the copy quantity display.

2 IN 1 OR 4 IN 1

Enter the desired pattern number using a numeric key.

The entered number will blink in the copy quantity display. For layout

pattern numbers, see the previous page.

Press the START key.

The entered number will light up steadily.

Press the 2 IN 1 / 4 IN 1 key to complete the selection.

The copy ratio will be calculated automatically. If the calculated copy

ratio is less than 50%, part of original image may not be copied

because the smallest copy ratio is 50%.

Set the number of copies.

Press the START key.

Copying will start after the originals have been scanned. Up to 30

sheets of originals can be scanned. (If originals are fed continuously

using the stream feeding mode, up to approximately 60 sheets of 8-1/

2" x 11" originals can be scanned. However, when copying originals

which require more memory such as photographs, the number of

originals which can be scanned will be less.) When the memory

becomes full of scanned original image data, the ORIGINAL DATA

indicator will blink.

When the ORIGINAL DATA indicator blinks, the copier will stop

scanning. Tostartcopyingofscannedoriginals, presstheSTARTkey.

To cancel copying, press the CLEAR or CLEAR ALL key.

ERASE

Edge erase

This copier has an edge erase mode and a center erase mode.

Edge erase can be used to eliminate shadow lines around the edges of

copies caused when thick paper or a book is used as an original.

Center erase can be used to eliminate the shadow produced by the

bindings of bound documents.

Center erase

Edge + center erase can be used to eliminate shadow lines around the

edges of copies and to eliminate the shadow at the center of copies.

The erase width can be set from 0" to 1" in five steps using user program

A B

No. 16. See page 46.

This feature cannot be used with the 2 in 1 or 4 in 1 feature.

Edge + Center erase

A B

Place the original on the original table and close the

platen cover.

The SPF can also be used for this feature.

Press the ERASE key to select the desired erase mode.

To select the EDGE + CENTER ERASE mode, press the ERASE key

until both the EDGE and CENTER indicators light up.

Check the copy paper size.

The bypass tray and any tray with non-standard size paper cannot be

used for this feature.

If an optional paper feed unit is installed, use the TRAY SELECT key

to select the desired paper size.

ERASE

Set the number of copies.

Press the START key.

MARGIN SHIFT

The MARGIN SHIFT feature automatically shifts the text or image to

the right to increase the left margin by approximately 1/4".

Original

Copy

This feature cannot be used with the 2 in 1 or 4 in 1 feature.

Expanded margin

Place the original in the document feeder tray or on the

original table.

Margin is expanded here.

When copying from the original table, set the original face down so

that the margin side is positioned at the right side.

Press the MARGIN SHIFT key.

Check the copy paper size.

If an optional paper feed unit is installed, use the TRAY SELECT key

to select the desired paper size.

Set the number of copies and press the START key.

INTERRUPTING A

TONER CARTRIDGE REPLACEMENT

When the toner cartridge replacement required ( ) indicator lights up,

For best copying results, be sure to use only

SHARP Genuine Supplies which are designed,

engineered and tested to maximize the life and

performance of SHARP copiers. Look for the

Genuine Supplies label on the toner package.

replacement of the toner cartridge will be needed soon. Obtain a new

cartridge. When the toner cartridge replacement required ( ) indicator

blinks, the toner cartridge must be replaced before copying can be resumed.

Replace the toner cartridge by following the procedure below.

During a long copy run of a dark original, the

indicator may blink and the copier stop, even though

toner is left.The copier will feed toner up to 2 minutes

and then the START key indicator will light up. Press

the START key to restart copying.

Open the bypass tray. Lift slightly on the side cover and

slide the cover out until it stops.

Push gently on both sides of the front cover and open it.

Push the toner cartridge lock release lever and pull the

toner cartridge out. Remove the toner cartridge while

supportingitwiththelefthandatthegreenlabelposition.

Toner cartridge lock

release lever

For disposal of the old toner cartridge, contact your dealer.

Afterremovingthetonercartridge,donotshakeitortap

on it. Doing so may cause toner to leak from the

cartridge. Put the old cartridge immediately in the bag

contained in the box of the new cartridge.

Grip

Remove the new toner cartridge from the bag. Grasp the

cartridge on both sides and shake it horizontally four or

five times. After shaking the cartridge, remove the tape.

4 or 5 times

Grasp the grip when holding the cartridge. Do not hold

the cartridge by the shutter. Be sure to only shake the

cartridge before the tape is removed.

Shutter

Tape

TONER CARTRIDGE REPLACEMENT

Gently insert the toner cartridge along the guides until

it locks in place while pushing the lock release lever.

If dirt or dust is adhered to the toner cartridge, remove

it before installing the cartridge.

Remove the tape from the shutter. Pull the shutter out of

the toner cartridge as shown in the illustration. Discard

the shutter.

Close the front cover by pushing both sides with your

hands and then close the side cover by pressing the

handle on the cover. The

indicator will go out.

When closing the covers, be sure to close the front

cover securely and then close the side cover. If the

covers are closed in the wrong order, the covers may

be damaged.

Evenafteranewtonercartridgeisinstalled,theSTART

keyindicatormaynotlightup,indicatingcopyingcannot

be restarted (toner is not sufficiently fed). In this case,

open and close the side cover. The copier will feed

toner again approximately 2 minutes and then copying

can be restarted.

Toner cartridge life

Tofindouttheapproximatequantityoftonerremaining,followtheprocedure

below.

Press and hold the light ( ) key for more than 5

seconds until all the alarm indicators (

and

) blink and “– –” appears in the copy quantity

display.

Press and hold the copy ratio display ( ) key for more

than 5 seconds.

The approximate quantity of toner remaining will be indicated in the

copy quantity display as a percentage. ( “100”, “75”, “50”, “25”, or

“10” is displayed.) When the percentage is less than 10%, “LO” will

be displayed.

Press the light ( ) key.

All the alarm indicators will go out.

MISFEED REMOVAL

The copier will stop when a misfeed occurs. The misfeed

) indicator will blink, and blinking red misfeed location

indicators will indicate the approximate misfeed location.

If paper is accidentally torn during removal, be sure to

remove all pieces.

Be careful not to damage the photoconductive drum.

For misfeeds in optional equipment, see their section of the

operation manual.

(

First confirm the misfeed location.

(

P. 40)

P. 41, 44)

(

P. 68)

Misfeed in the SPF

If an original misfeed occurs in the SPF, the copier will

stop and the red indicator which indicates an original

misfeed will blink.

Location A

Openthefeedingrollercoverandpulltheoriginalgently

to the left and out from the document feeder tray. Close

the feeding roller cover.

Feeding roller cover

Location B

If the misfed original cannot be removed in step 1, open

the right side cover and remove the misfed original.

Close the right side cover.

Right side cover

MISFEED REMOVAL

Location C

If the misfed original cannot be removed in steps 1 and

2, remove the misfed original from the exit area. Open

the document feeder cover and rotate the roller in the

direction indicated by the arrow if needed.

If the misfed original cannot be easily removed from the

exit area, open the front part of the document feeder tray

to remove the original.

Roller

Open and close the document feeder cover to cancel the

misfeed location indicator.

After misfed originals are removed, a number may

appear in the copy quantity display, indicating the

number of originals that must be returned to the

document feeder tray. Return the originals and press

the START key to resume copying.

Misfeed in the bypass tray

Gently pull the misfed paper out.

Lift slightly on the side cover and slide the cover out

until it stops. Close the side cover by pressing the

handle on the cover.

The misfeed ( ) indicator will go out.

Misfeed in the copier

Open the bypass tray. Lift slightly on the side cover and

slide the cover out until it stops.

MISFEED REMOVAL

Check the misfeed location. Remove the misfed paper

following the instructions for each location in the

illustration below.

If paper is misfed here, proceed to

“B. Misfeed in the fusing area”.

If the misfed paper is seen from this

side, proceed to “C. Misfeed in the

transport area”.

If paper is misfed here, proceed to

“A. Misfeed in the paper feed area”.

A. Misfeed in the paper feed area

Push gently on both sides of the front cover and open it.

Carefully remove the misfed paper. Turn the roller

rotating knob in the direction of the arrow to assist in

removing it.

Roller rotating knob

The fusing unit is hot. Take care in removing paper.

Donottouchthephotoconductivedrum(greenportion)

when removing the misfed paper. Doing so may

damage the drum and cause smudges on copies.

Close the front cover by pushing both sides with your

hands and then close the side cover by pressing the

handle on the cover.

The misfeed ( ) indicator will go out.

When closing the covers, be sure to close the front

cover securely and then close the side cover. If the

covers are closed in the wrong order, the covers may

be damaged.

B. Misfeed in the fusing area

Push gently on both sides of the front cover and open it.

MISFEED REMOVAL

Turn the roller rotating knob in the direction of the

arrow.

Roller rotating knob

Carefully remove the misfed paper. Lower the fusing

unit release levers to allow easier removal. Return the

release levers to their operating positions.

Fusing unit release levers

The fusing unit is hot. Take care in removing paper.

Do not touch the photoconductive drum (green

portion) when removing the misfed paper. Doing so

may damage the drum and cause smudges on

copies.

Be careful about unfixed toner on the misfed paper

not to soil your hands or clothes.

Close the front cover by pushing both sides with your

hands and then close the side cover by pressing the

handle on the cover.

The misfeed ( ) indicator will go out.

When closing the covers, be sure to close the front

cover securely and then close the side cover. If the

covers are closed in the wrong order, the covers may

be damaged.

C. Misfeed in the transport area

Open the paper guide by pressing down the projection

on either side of the guide and remove the misfed paper.

The fusing unit is hot. Take care in removing paper.

If the misfed paper cannot be removed by the previous

step but is visible in the paper output area, remove the

paper by pulling it into the paper output area.

MISFEED REMOVAL

Close the side cover by pressing the handle on the

cover.

The misfeed ( ) indicator will go out.

Misfeed in the paper tray

Before opening the paper tray, be sure to open the bypass tray, lift slightly

on the side cover and slide the cover out until it stops, and then perform steps

1 to 3 described in the “A. Misfeed in the paper feed area” section.

Gently lift and pull out the paper tray and remove the

misfed paper.

Close the paper tray.

Lift slightly on the side cover and slide the cover out

until it stops. Close the side cover by pressing the

handle on the cover.

The misfeed ( ) indicator will go out.

DEVELOPER REQUIRED

When the

indicator lights up, the developer should be replaced.

DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN

AUTHORIZED SHARP SERVICE TECHNICIAN. Contact your service

center as soon as possible.

MAINTENANCE REQUIRED

When the

indicator lights up, service by an authorized SHARP service

technician is required. Contact your service center as soon as possible.

USER PROGRAMS

The user programs allow the parameters of certain functions to be set,

changed, or canceled as desired.

List of user programs

This copier has the following user programs.

Program No. Program name

Description

Auto clear time

Sets the auto clear time. The copier returns to the initial settings when

the auto clear time elapses after the last copy is made.

Preheat mode

Sets the time that elapses before the copier enters the preheat mode after

any operation is made. See page 53.

Auto power shut-off

timer

Sets the time that elapses before the copier enters the auto power

shut-off mode after any operation is made. See page 53.

Stream feeding

mode

Enables or disables the stream feeding mode. See page 14.

Auto power shut-off

setting

Enables or disables the auto power shut-off mode. See page 53.

Border line for 2 in 1 or Enables or disables the border line which is printed in 2 in 1 or 4 in 1

4 in 1

copying. See page 33.

Rotation copy

Enables or disables rotation of original images. See page 32.

Auto paper select mode Enables or disables the auto paper selection. See page 14.

Auto tray switching*

Auditing mode

Enables or disables the automatic tray switching which occurs when paper

in a tray runs out. (This switching cannot switch to the bypass tray.)

Enables or disables the auditing mode, which controls access to

copier. See page 13.

Account number

entry

Registers accounts for auditing mode.

Account number

change

Changes account numbers for auditing mode.

Deletes accounts for auditing mode.

Account number

deletion

Number of copies

per account

Displays the total number of copies made against account numbers.

Resetting account

Resets all audit accounts or resets any desired individual account.

Erase width adjustment Sets the amount of the edge erase and center erase areas. See page 35.

Layout in 2 in 1 copy

Layout in 4 in 1 copy

Selects a pattern for 2 in 1 copying. See page 33.

Selects a pattern for 4 in 1 copying. See page 33.

Offset of paper output

tray

Enables or disables the offset function of the paper output tray. The offset

function can be specified respectively for the upper and lower areas

separated by an optional job separator tray. See page 23.

* This program does not affect the copier functions unless certain optional equipment is installed.

USER PROGRAMS

Setting the user programs

Press and hold the light ( ) key for more than 5

seconds until all the alarm indicators ( ,

and

) blink and “––” appears in the copy quantity

display.

Enter a program number using the numeric keys.

The selected program number will blink in the copy quantity display.

If a mistake is made in steps 2 to 4, press the CLEAR ( ) key. The

copier will return to step 2.

The program numbers are shown in the table below.

For example, to change the setting of the auto power shut-off timer,

press key 3.

Program name

Program No.

Auto clear time

Preheat mode

Auto power shut-off timer

Stream feeding mode

Auto power shut-off setting

Border line for 2 in 1 or 4 in 1

Rotation copy

Auto paper select mode

Auto tray switching

Auditing mode

Account number entry

Account number change

Account number deletion

Number of copies per account

Resetting account

For operation of these programs after

step 3, see page 49.

Erase width adjustment

Layout in 2 in 1 copy

Layout in 4 in 1 copy

Offset of paper output tray

Press the START key.

For programs 1 to 9 and 16 to 19, the entered program number will be

steadily lit on the left side of the copy quantity display and the

currently selected parameter number for the program will blink on the

right side.

For programs 10 to 15 (programs for auditing accounts), the display

varies with the program number. See page 49 for setting programs 10

to 15.

USER PROGRAMS

Select the desired parameter using the numeric keys.

The entered parameter number will blink on the right side of the copy

quantity display.

The parameters are shown in the table below.

For example, to change the setting of the auto power shut-off timer to

60 min., press key 2.

Program name

Parameters

Auto clear time

OFF

10 sec.

30 sec.

* 2

60 sec.

90 sec.

120 sec.

Preheat mode

* 1

* 0

OFF

30 sec.

60 min.

60 sec.

* 3

90 sec.

120 sec.

240 min.

Auto power shut-off timer

Stream feeding mode

Auto power shut-off setting

30 min.

OFF

90 min.

120 min.

OFF

* 1

Border line for 2 in 1 or 4 in 1 * 0

OFF

Rotation copy

OFF

* 1

Auto paper select mode

Auto tray switching

Erase width adjustment

Layout in 2 in 1 copy

Layout in 4 in 1 copy

Offset of paper output tray

OFF

1/4"

* 2

1/2"

3/4"

* 1

Pattern 1

Pattern 2

Pattern 3

Pattern 4

Upper OFF, lower OFF

Upper ON, lower OFF

* 1

Upper ON, lower ON

Upper OFF, lower ON

Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 33.

If you select “0” (OFF) in a program, the corresponding

function will be disabled.

Press the START key.

The right-hand number in the copy quantity display will be steadily lit

and the entered value will be stored.

To continue with other user programs, press the

key

and then repeat steps 2 to 5. To exit the user program

mode, press the light ( ) key.

All the alarm indicators will go out.

USER PROGRAMS

Settings for auditing accounts

Setting of user programs No. 10 to 15 varies with the program number. For

settings of all programs, first follow steps 1 to 3 in “Setting the user

programs” on page 47 to select a program. (1. Press the light ( ) key for

morethan5seconds. 2. Enteraprogramnumber(10to15)usingthenumeric

keys. 3. Press the START key.) Then follow the appropriate instructions for

the program.

Program No. 10: Auditing mode

If the auditing mode is enabled, copying is limited to operators with an

assigned3-digitaccountnumber.Amaximumof20,3-digitaccountnumbers

can be assigned. Use program No. 11 to register account numbers.

When program No. 10 is entered, the current setting (0: OFF, 1:ON) will

blink on the right side of the copy quantity display.

1. Select the desired setting using the numeric keys.

0: OFF

1: ON

2. Press the START key.

The setting will be stored.

3. To continue with other user programs, press the

key

and enter another program number. To exit the user

program mode, press the light ( ) key.

Program No. 11: Account number entry

ProgramNo.11isusedtoregisteraccounts.WhenprogramNo.11isentered,

“–––” will blink in the copy quantity display.

If the number of accounts has reached the upper limit (20), “11E” will

appear in the copy quantity display. Press the

return to step 2 on page 47.

key. The copier will

1. Enter a 3-digit account number using the numeric keys.

Any 3-digit number except “000” can be registered as an account

number.

2. Press the START key.

If a number that is already registered or “000” is entered, the number

will blink in the copy quantity display.

3. Repeat steps 1 and 2 for other account numbers.

4. To continue with other user programs, press the

key

and enter another program number. To exit the user

program mode, press the light ( ) key.

USER PROGRAMS

Program No. 12: Account number change

Program No. 12 is used to change account numbers. When program No. 12

is entered, an account number will appear in the copy quantity display.

If no account number has been registered, “12E” will appear in the copy

quantitydisplay.Pressthe

47.

key.Thecopierwillreturntostep2onpage

1. Use the copy ratio display ( ) key to select the account

number to be changed.

Use the

key to advance through the account numbers.

2. Press the START key.

The account number will be erased and “–––” will blink in the copy

quantity display.

3. Enter a new account number using the numeric keys.

4. Press the START key.

If a number that is already registered or “000” is entered, the number

will blink in the copy quantity display.

5. Repeat steps 1 to 4 for other account numbers.

6. To continue with other user programs, press the

key

and enter another program number. To exit the user

program mode, press the light ( ) key.

Program No. 13: Account number deletion

Program No. 13 is used to delete accounts. When program No. 13 is entered,

“0” will blink on the right side of the copy quantity display.

If no account number has been registered, “13E” will appear in the copy

quantitydisplay. Pressthe

47.

key. Thecopierwillreturntostep2onpage

1. To delete an individual account, press the 0 key.

To delete all accounts, press key 1.

2. Press the START key.

If you have pressed the 0 key in step 1, an account number will appear

in the copy quantity display. Proceed to step 3.

If you have pressed key 1, all account numbers will be deleted.

Proceed to step 5.

3. Use the copy ratio display ( ) key to select the account

number to be deleted.

Use the

key to advance through the account numbers.

4. Press the START key.

The specified account will be deleted.

5. To continue with other user programs, enter another

program number. To exit the user program mode, press

the light ( ) key.

USER PROGRAMS

Program No. 14: Number of copies per account

Program No. 14 is used to display the total number of copies made against

each account number. When program No. 14 is entered, an account number

will appear in the copy quantity display.

If no account number has been registered, “14E” will appear in the copy

quantitydisplay.Pressthe

47.

key.Thecopierwillreturntostep2onpage

1. Use the copy ratio display ( ) key to select the account

number.

Use the

key to advance through the account numbers.

2. Press and hold down the 0 key.

The number of copies made against the specified account number will

be displayed. The two higher digits and the three lower digits will

appear alternately while the 0 key is pressed.

Example: 1,234 copies

The upper limit for the number of copies is 49,999. If the number of

copiesmadereaches50,000,thenumberwillberesetto0andcounting

will start again from 0.

3. Repeat steps 1 and 2 for other account numbers.

4. To continue with other user programs, press the

key

and select another program number. To exit the user

program mode, press the light ( ) key.

USER PROGRAMS

Program No. 15: Resetting account

Program No. 15 is used to reset all accounts or to reset any desired individual

account. When program No. 15 is entered, “0” will blink on the right side of

the copy quantity display.

If no account number has been registered, “15E” will appear in the copy

quantitydisplay. Pressthe

47.

key. Thecopierwillreturntostep2onpage

1. To reset an individual account, press the 0 key.

To reset all accounts, press key 1.

2. Press the START key.

If you have pressed the 0 key in step 1, an account number will appear

in the copy quantity display. Proceed to step 3.

If you have pressed key 1, the number of copies against all account

numbers will be reset. Proceed to step 5.

3. Use the copy ratio display ( ) key to select the account

number to be reset.

Use the

key to advance through the account numbers.

4. Press the START key.

The number of copies against the specified account number will be

reset.

5. To continue with other user programs, enter another

program number. To exit the user program mode, press

the light ( ) key.

POWER SAVE MODES

The copier has two power save modes to reduce overall power consumption

thereby reduce the cost of operation. In addition, these modes conserve

natural resources and help reduce environmental pollution. The two power

save modes are preheat mode and auto power shut-off mode.

User programs

The preheat activation time and the auto power shut-off time have been

presetatthefactoryto90sec. forpreheatmodeand30min. forautopower

shut-off mode. These times can be changed using user programs. It is

suggested that you set appropriate times according to the actual usage of

the copier. See page 46.

Preheat mode

When the copier enters the preheat mode, the POWER SAVE indicator will

light up and other indicators will remain on or off as before. In this condition,

the fuser in the copier is maintained at a lower heat level, thereby saving

power. The preheat level is, however, high enough to allow the copier to

come to a ready condition or begin copying within 10 seconds after any key

input or copier operation such as paper tray operation is performed.

Auto power shut-off mode

If the auto power shut-off mode is enabled, the copier will automatically turn

off the power once a programmed length of time has elapsed without any

copieroperationafterthelastcopyofarunismadeorthepowerisfirstturned

on. The power switch will automatically be turned to the “OFF” position.

To turn the power back on, simply turn the power switch to the “ON”

position.

If an optional printer expansion kit or facsimile expansion kit is installed

and this mode is enabled, the POWER SAVE indicator will light up and

all other indicators will go out. The auto power shut-off mode saves more

power but requires a longer time to warm up before copying can begin.

AsanENERGYSTAR^®Partner,SHARP

has determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency.

POWER SAVE MODES

Setting the power save modes

The time that elapses before the copier enters a power save mode after any

operationismadecanbesetmanually. ThistimeissetwithuserprogramNo.

2 for the preheat mode and user program No. 3 for the auto power shut-off

mode. For these settings, see page 47.

The copier will enter the preheat mode first and then the auto power shut-

offmodeafterapresettimehaselapsedwhennocopieroperationhasbeen

made.

IfconflictingsettingsaremadewithuserprogramsNo.3andNo.5,thelast

program set will have priority.

Copying from the preheat mode

Make desired copier selections and press the START

key using the normal copying procedure.

When any key input is made or any other copier operation is made, the

POWER SAVE indicator will start to blink.

When the START key is pressed, the START key indicator will go out

andcopyingwillstartwithin10seconds.ThePOWERSAVEindicator

will go out when copying starts.

Copying from the auto power shut-off mode

Only available when an optional printer expansion kit or facsimile

expansion kit is installed.

Press the START key.

The copier will exit the auto power shut-off mode and the POWER

SAVE indicator will start to blink.

Make desired copier selections and press the START

key using the normal copying procedure.

It will take approximately 35 seconds for the copier to start copying.

However, you can make desired settings and press the START key

during warm-up. Copying will start after warm-up is finished.

USER MAINTENANCE

Proper care is essential for clean, sharp copies. Please take a few minutes to

regularly clean your copier.

Original table and platen cover

Stains or dirt on the original table or platen cover will

also be copied. Wipe the original table and platen cover

with a soft, clean cloth.

If necessary, dampen the cloth with water. Do not use thinner,

benzene, or similar volatile cleaning agents.

Wipe the scanning window on the original table.

Bypass tray paper feed roller

If misfeeds occur frequently when feeding postcards,

envelopes, thick paper, etc. through the bypass tray,

wipe the blue paper feed roller at the feed slot of the

bypass tray with a soft, clean cloth dampened with

alcohol or water.

Paper feed roller

USER MAINTENANCE

Transfer charger cleaning

Ifcopiesstartbecomingstreakyorblotchy, thetransferchargermaybedirty.

Clean the charger using the following procedure.

Turn the power switch off.

Open the bypass tray. Lift slightly on the side cover and

slide the cover out until it stops.

Gently lift and pull out the paper tray and take the

charger cleaner out by holding the tab.

Charger

cleaner

Set the charger cleaner onto the transfer charger and

gently slide the cleaner in the direction indicated by the

arrow two or three times.

Slidethechargercleanerfromoneendtotheotherend

along the groove of the transfer charger. If the cleaner

is stopped on the way, smudges on copies may occur.

Ifthewhitesheetmetalissmudgedwithtoner,wipeitwithasoft,clean

cloth.

Returnthechargercleanertoitsoriginalposition. Close

the paper tray. Close the side cover by pressing the

handle on the cover.

Turn the power switch on.

COPIER TROUBLE?

Problem

Solution

Copier plugged in?

Plug the copier into a grounded outlet.

See page 8.

Copier does not operate.

Power switch ON?

Turn the power switch ON.

See page 14.

Copies are too dark or

too light.

Copy density properly adjusted?

See pages 14 and 26.

Is the original placed face up in the

SPF or face down on the original

table?

PlacetheoriginalfaceupintheSPForfacedown

on the original table.

Blank copies

Paper too heavy?

Paper damp?

Use copy paper within the specified range. See

page 60.

Copies smear if rubbed.

Replace with dry copy paper.

Be sure to store copy paper in a dry location. See

page 61.

Striped copies

Is transfer charger clean?

Non-standard paper used?

Clean the transfer charger. See page 56.

Use standard paper. If using special paper, feed

the paper through the bypass tray.

See pages 20 and 60.

Paper properly installed?

Pieces of paper inside copier?

Paper curled or damp?

Make sure the paper is properly installed. See

pages 10 and 20.

Paper misfeeds frequently.

Remove all pieces of misfed paper.

See page 40.

Store copy paper flat in the wrapper in a dry

location. See page 61.

COPIER TROUBLE?

Problem

Solution

Original table or document feeder

Clean regularly. See page 55.

cover dirty?

Original smudged or blotchy?

Use a clean original.

Copies are smudged

or dirty.

Is the

indicator on?

Developer is required. Contact your SHARP

service center as soon as possible. See page 45.

Maintenance is required. Contact your SHARP

service center as soon as possible. See page 45.

Is the COPY indicator off?

Use the COPY/FAX key to select the COPY

mode. See Note below.

Paper size for a paper tray

cannot be set.

Is copying, printing or facsimile

printing being performed?

Set the paper size after copying, printing or

facsimile printing is complete.

Is the POWER SAVE indicator

blinking?

Wait until warm-up is complete.

Warm-up time is approximately 35 seconds.

Is only the POWER SAVE

indicator on? (when an optional

printer or facsimile expansion kit is

installed)

The copier is in the auto power shut-off mode.

Press the START key. See page 53, POWER

SAVE MODES.

Power is on but copying

is not possible.

Is the COPY indicator off?

Use the COPY/FAX key to select the COPY

mode. See Note below.

steadily lit in the copy

The copier is in the auditing mode.

Enter your account number using the numeric

keys. See page 13.

quantity display?

Is the

indicator on?

Copy paper is needed. See page 10, LOADING

COPY PAPER.

COPY/FAX key

The COPY/FAX key is used to switch

between the FAX and COPY modes.

For details, see the MULTI ACCESS

manual.

COPIER TROUBLE?

Problem

Solution

blinking in the copy

A toner cartridge is not installed. Install a toner

cartridge. If "CH" is blinking even if a

cartridge is installed properly, contact your

SHARP service center immediately.

quantity display?

steadily lit in the copy

Side cover(s) is open.

Close the front and side covers securely.

quantity display?

Power is on but copying

is not possible.

Is the

indicator blinking?

The toner cartridge must be replaced. See page

38, TONER CARTRIDGE REPLACEMENT.

indicator blinking?

A misfeed has occurred. See page 40,

MISFEED REMOVAL.

Is the same power outlet used for

the lighting fixture and the copier?

Connect the copier to a power outlet which is

not used for other electric appliances.

Lighting fixture flickers.

BesuretouseonlygenuineSHARPpartsandsupplies.

Please contact your SHARP service center immediately if a problem persists

after checking the above.

Self-diagnostic function

An automatic self-diagnostic function is built into the copier. Should the

copier malfunction, the self-diagnostic function will locate the problem and

stop the copier to prevent damage. An alphanumeric code will appear in the

copy quantity display.

Example

Shouldthecopiercompletelystopandaletterandanumberappearalternately,

contact your SHARP service center immediately.

SUPPLIES

Types and sizes of copy paper

Size

Weight

Capacity

Special paper

(21 lb. bond paper)

Paper tray

5-1/2" x 8-1/2"*

to 11" x 17"

15 lbs. to 21 lbs.

250 sheets

Bypass tray

Ordinary paper:

5-1/2" x 8-1/2"

to 11" x 17"

15 lbs. to 34 lbs.** 100 sheets

(Ordinary paper)

Transparency film,

labels, envelopes***

Envelopes:

Commercial 10

(4-1/8" x 9-1/2")

International DL

(110 x 220 mm)

International C5

(162 x 229 mm)

5-1/2" x 8-1/2" copy paper can be used in the uppermost paper tray but

cannot be used in other trays (in optional paper feed units).

** For paper weighing from 28 to 34 lbs., 8-1/2" x 11" is the maximum size

that can be fed through the bypass tray.

*** Do not use envelopes that have metal clasps, plastic snappers, string

closures, windows, linings, self-adhesivepatchesorsyntheticmaterials.

These will cause physical damage to the copier.

For best results, use only paper recommended by SHARP.

Special papers except envelopes must be fed one sheet at a time through

the bypass tray. Up to 10 envelopes can be set at one time.

SUPPLIES

Genuine supplies statement

For best copying results, be sure to use only

SHARP Genuine Supplies which are

designed, engineered and tested to maximize

the life and performance of SHARP copiers.

Look for the Genuine Supplies label on the

toner package.

Standard supplies for this copier that are to be replaced by the user are copy

paper and toner cartridge.

Proper storage

1. Store the supplies in a location that is:

clean and dry,

at a stable temperature,

not exposed to direct sunlight.

2. Store copy paper in the wrapper and lying flat.

Paper stored out of the wrapper or in packages standing on end may

curl or get damp, resulting in paper misfeeds.

SPECIFICATIONS

Type

Desktop

Copy system

Originals

Dry, electrostatic transfer

Sheets, bound documents

Max. 11" x 17"

Original sizes

Copy sizes

Max. 11" x 17"

Min. 5-1/2" x 8-1/2"

Image loss: Max. 5/32" (4 mm) (leading and trailing edges)

Max. 5/32" (4 mm) (along other edges in total)

Copying speed

(at 100% copy ratio)

16 copies/min. (8-1/2" x 11")

12 copies/min. (8-1/2" x 11"R)

10 copies/min. (8-1/2" x 14")

9 copies/min. (11" x 17")

Continuous copy

First-copy time

Warm-up time

Copy ratio

Max. 99 copies; subtractive counter

7.2 s (except in a power save mode)

Approx. 35 s

Variable: 50% to 200%, in 1% increments (total 151 steps)

Fixedpreset:50%,64%,77%,95%,100%,121%,129%,141%,

200%

Exposure system

Copy paper feed

Original table: Moving optical source, slit exposure (stationary

platen) with automatic exposure function

SPF: Moving originals

Onepapertraywithautomaticfeed (250sheets),onebypasstray

with automatic feed (100 sheets)

Fusing system

Developer system

Light source

Heat rollers

Magnetic brush development

Xenon lamp

Resolution

Scan: 400 dpi

Output: 600 dpi

Gradation

Scan: 256 levels

Output: 2 levels

Power supply

AC 120V, 60 Hz, 11 amperes

Max. 1.3 kW

Power consumption

SPECIFICATIONS

Overall dimensions

(with bypass tray folded)

23-15/64" (W) x 20-29/32" (D)

(590 mm (W) x 531 mm (D))

Weight

Approx. 70.6 lbs. (32 kg)

Toner cartridge included

Copier dimensions

Operating conditions

23-15/64" (W) x 20-29/32" (D) x 18-33/64" (H)

(590 mm (W) x 531 mm (D) x 470 mm (H))

Temperature: 59°F to 86°F (15°C to 30°C)

Humidity: 20% to 85%

Acoustic noise emission

(measurement according

to ISO 7779)

Sound power level LWA

Operating: 6.1 [B], Standby: 3.2 [B]

Sound pressure level L^PA (Bystander positions)

Operating: 47 [dB (A)], Standby: 17 [dB (A)]

Sound pressure level LPA (Operator positions)

Operating: 50 [dB (A)], Standby: 18 [dB (A)]

Emission concentration

(measurement according to

RAL-UZ 62)

Ozone: less than 0.02 mg/m³

Dust: less than 0.075 mg/m³

Styrene: less than 0.07 mg/m³

Optional equipment

250-sheet paper feed unit (AR-DE5)

2x250-sheet paper feed unit (AR-DE6)

Facsimile expansion kit (AR-FX2)

Printer expansion kit (AR-PB8)

PS2 expansion kit (AR-PS1)

LCD panel kit (AR-PA1)

Job separator tray kit (AR-TR2)

Print server card (AR-NC3D)

SINGLE PASS FEEDER

Acceptable

originals

Weight: 15 to 24 lbs.

Size: 5-1/2" x 8-1/2" to 11" x 17"

Capacity: Up to 30 sheets provided the total aggregate

thickness does not exceed 5/32"

Detectable original

sizes

5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14",

11" x 17"

First-copy time may differ depending on operating conditions, such as power-supply voltage and

room temperature.

As a part of our policy of continuous improvement, SHARP reserves the right

to make design and specification changes for product improvement without

prior notice. The performance specification figures indicated are nominal

values of production units. There may be some deviations from these values

in individual units.

MEMO

OPTIONAL

EQUIPMENT

CONTENTS

Page

SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

250-SHEET PAPER FEED UNIT (AR-DE5)/

2x250-SHEET PAPER FEED UNIT (AR-DE6) . . . . . . . . . . . . . . 67

Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Misfeed removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

SYSTEM CONFIGURATION

A number of options are available for the copier which allow you to

configure a copier system to meet your particular needs. The options include

the following.

Facsimile expansion kit (AR-FX2)*

Printer expansion kit (AR-PB8)*

PS2 expansion kit (AR-PS1)*

LCD panel kit (AR-PA1)*

Job separator tray kit (AR-TR2)*

Print server card (AR-NC3D)*

* These options are not used for the copier

operation.

250-sheet paper feed unit

(AR-DE5)

2x250-sheet paper feed unit

(AR-DE6)

(AR-DE5)

250-SHEET PAPER FEED UNIT

2x250-SHEET PAPER FEED UNIT

(AR-DE6)

Thesepaperfeedunitsasoptionsprovidetheconvenienceofincreasedpaper

capacity for the copier and a greater choice of paper sizes readily available

for copying.

The AR-DE5 contains one 250-sheet paper tray and the AR-DE6 contains

two 250-sheet paper trays.

PART NAMES

250-sheet paper feed unit

AR-DE5

2 x 250-sheet paper feed unit

AR-DE6

Side cover

Tray

Trays

Loading copy paper

Themethodofloadingcopypaperforthepapertraysofthesepaperfeedunits

is the same as for the paper tray in the copier. See page 10.

Themethodofchangingthecopypapersizeisalsothesameforthepapertray

in the copier. See page 11.

250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6)

Misfeed removal

The copier will stop when a misfeed occurs. The misfeed ( ) indicator and

the red indicator which indicates the paper feed unit will blink.

Open the side cover of the paper feed unit and remove

the misfed paper.

Be sure to perform this step before pulling out the paper trays. If not,

the paper may be torn as the trays are opened.

Gently lift and pull out the paper tray which was in use.

Remove any misfed paper.

Close the paper tray and the side cover.

Confirm that the misfeed ( ) indicator has gone out.

250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6)

Specifications

AR-DE5

Copy paper size

Paper weight

8-1/2" x 11" to 11" x 17"

15 lbs. to 21 lbs.

Paper capacity

Onepapertraywithcapacityfor250sheetsof21lb. bond

paper

Weight

Approx. 10.4 lbs. (4.7 kg)

Dimensions

23-15/64" (W) x 18-35/64" (D) x 3-15/32" (H)

(590 mm (W) x 471 mm (D) x 88 mm (H))

Power supply

Drawn from the copier

AR-DE6

Copy paper size

Paper weight

8-1/2" x 11" to 11" x 17"

15 lbs. to 21 lbs.

Paper capacity

Two paper trays with capacity for 250 sheets of 21 lb.

bond paper each

Weight

Approx. 20.1 lbs. (9.1 kg)

Dimensions

23-15/64" (W) x 18-35/64" (D) x 6-27/32" (H)

(590 mm (W) x 471 mm (D) x 173.5 mm (H))

Power supply

Drawn from the copier

Asapartofourpolicyofcontinuousimprovement,SHARPreserves

the right to make design and specification changes for product

improvement without prior notice. The performance specification

figuresindicated arenominalvalues of production units. Theremay

be some deviations from these values in individual units.

INDEX

250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . . . 67

2 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

2x250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . 67

Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Light key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 39, 47

4 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Auto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 46

Automatic exposure adjustment . . . . . . . . . . . . . . . . . . 26

Auto power shut-off mode . . . . . . . . . . . . . . . . . . . . . . 53

Maintenance

– user maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

– maintenance required indicator . . . . . . . . . . . . . . . . . 45

Manual exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Manual feeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Margin shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Misfeed removal

B/W reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

– bypass tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

– in the copier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

– paper tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44, 68

– SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Cautions on handling . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Copier trouble? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Copying

– normal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

– reduction/enlargement. . . . . . . . . . . . . . . . . . . . . . . . 18

– through bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . 20

– two-sided . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 60

Copy quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Copy ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Names

– operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

– part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Original table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Dark key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Developer replacement required indicator . . . . . . . . . . 45

Dual page copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Paper

– loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

– special . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

– specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Paper output tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Paper size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Paper tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Photo mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Platen cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Power save modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Preheat mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Enlargement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Exposure adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Fixed copy ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Fusing unit release levers . . . . . . . . . . . . . . . . . . . . . . . 43

Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

INDEX

Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Replacement

– toner cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Single pass feeder (SPF) . . . . . . . . . . . . . . . . . . . . . . . . 14

Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Special paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Specifications

– copier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

– paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Storage of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Stream feeding mode . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Toner cartridge life . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Toner cartridge replacement. . . . . . . . . . . . . . . . . . . . . 38

Toner save mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Total output count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Two-sided copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

User maintenance

– bypass tray paper feed roller . . . . . . . . . . . . . . . . . . . 55

– original table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

– platen cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

– transfer charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

User programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

XY zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Date Issued: Nov. 1, 2000

MSDS No. F-00991

MATERIAL SAFETY DATA SHEET

Section 1. Product Identification

Product:

AR-201NT/T/FT/ST (Black Toner)

Section 2. Supplier’s Name and Address

Sharp Corporation

22-22 Nagaike-cho, Abeno-ku, Osaka, Japan

Local suppliers are listed below. Please contact the nearest supplier for additional information.

(Country)

U.S.A.

(Name and Telephone Number)

Sharp Electronics Corporation

Telephone number for information: 1-800-237-4277

Emergency telephone number:

1-800-255-3924

Canada

Sharp Electronics of Canada Ltd.

Telephone number for information: 905-890-2100

Emergency telephone number:

1-800-255-3924

United Kingdom

Sharp Electronics (U.K.) Ltd.

Telephone number for information: 01923-474013

Section 3. Ingredients

Ingredients

Styrene-Acrylate copolymer

Carbon black

Iron oxide

Metal Complex dye

CAS No.

29497-14-1

1333-86-4

1309-38-2

109125-51-1

109125-50-0

Proportion OSHA PEL

ACGIHTLV Other Limits

> 88 %

< 6.0%

< 4.5%

< 1.5%

Not listed

3.5mg/m³

Not listed

0.5mg/m³

Not listed

3.5mg/m³

Not listed

0.5mg/m³

None

{

84179-66-8

Section 4. Hazardous Identification (Emergency Overview)

Toner is a fine, black powder possessing no immediate hazard.There are no anticipated carcinogenic effects from

exposure based on animal tests performed using toner.When used as intended according to instructions, studies

do not indicate any symptoms of fibrosis will occur.

Section 5. Health Hazard Data

Route(s) of Entry:

Inhalation?

Skin?

Ingestion?

Yes

Possible but very unusual.

Health Hazards: Acute oral toxicity ------- LDL0 of this toner is over 2,000mg/kg.

Mutagenicity ------------- The result of Ames test is negative.

Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human

carcinogen). This classification is given to chemicals for which there is inadequate human

evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The

classification is based upon the development of lung tumors in rats receiving chronic inhalation

exposures to free carbon black at levels that induce particle overload of the lung. Studies

performed in animal models other than rats did not show any association between carbon

black and lung tumors. Moreover, a two-year cancer bioassay using a typical toner preparation

containing carbon black demonstrated no association between toner exposure and tumor

development in rats.

Chronic Effect: In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of

lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m³) exposure

group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle

(4mg/m³) exposure group, but no pulmonary change was reported in the lowest (1mg/m³)

exposure group, the most relevant level to potential human exposures.

Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any

non-toxic dust.

Medical Conditions Generally Aggravated by Exposure: None

Emergency and First Aid Procedures:

Inhalation; Remove to fresh air. If effects occur, consult medical personnel.

Eye;

In case of contact, immediately flush eyes with water for 15 minutes.

Section 6. Physical Chemical Characteristics

Boiling / Melting Point: Not applicable

Specific Gravity:

1.1

Vapor Pressure:

Vapor Density:

Evaporation Rate:

Appearance:

Odor:

Not applicable

Fine powder

Odorless

Solubility inWater: Negligible

PH:

Not applicable

Viscosity:

Color:

Not applicable

Black

Section 7. Fire and Explosion Data

Flash Point (Method Used):

IgnitionTemperature:

Not applicable

>350°C

Flammable Limits:

(LEL); Not applicable

(UEL); Not applicable

Extinguishing Media:

Special Fire Fighting Procedure:

CO2, dry chemical, foam or water

None

Unusual Fire and Explosion Hazard: This material has no unusual fire or explosion hazards.

Sensitivity to Mechanical Impact:

Sensitivity to Static Charge:

None

Section 8. Reactivity Data

Stability:

Stable

Incompatibility (Material to Avoid):

Hazardous Decomposition:

Hazardous Polymerization:

None

CO and NOx

Will not occur.

Section 9. Precautions for Safe Handling and Use

Personal Protection Information (Respiratory, Eye Protection and Protective Glove):

Use of a dust mask is recommended when handling a large quantity of toner or during long term

exposure, as with any non-toxic dust.

Engineering Control /Ventilation:

Work / Hygienic Practice:

Not required.

Inhalation should be minimized as with any non-toxic dust.

Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner.

Waste Disposal Method:

Waste material may be dumped or incinerated under conditions

which meet all federal, state and local environmental regulations.

Section 10. Regulatory Information

NFPA Rating (U.S.A.):

WHMIS Legislation (Canada):

Transport Information:

UN No.:

Health = 1

Flammability = 1

This product is not a controlled product.

This product is not a hazardous material.

None allocated.

Reactivity = 0

Section 11. Other Information

References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans,

Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro Compounds, Lyon, pp-

149-261

H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie,

Morrow, U. Mohr, S. Takenaka, and R. Mermelstein (1991) Pulmonary Response to Toner upon

Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp. 280-299

Date Issued: Nov. 1, 2000

MSDS No. F-30991

MATERIAL SAFETY DATA SHEET

Section 1. Product Identification

Product

AR-201ND/DV/SD (Black Developer)

Section 2. Supplier’s Name and Address

Sharp Corporation

22-22 Nagaike-cho, Abeno-ku, Osaka, Japan

Local suppliers are listed below. Please contact the nearest supplier for additional information.

(Country)

U.S.A.

(Name and Telephone Number)

Sharp Electronics Corporation

Telephone number for information: 1-800-237-4277

Emergency telephone number:

1-800-255-3924

Canada

Sharp Electronics of Canada Ltd.

Telephone number for information: 905-890-2100

Emergency telephone number:

1-800-255-3924

United Kingdom

Sharp Electronics (U.K.) Ltd.

Telephone number for information: 01923-474013

Section 3. Ingredients

Ingredients

CAS No.

Proportion OSHA PEL

ACGIHTLV Other Limits

Iron powder

Styrene-Acrylate copolymer

Carbon black

7439-89-6

29497-14-1

1333-86-4

> 92.5%

< 7.0%

< 0.5%

Not listed

3.5mg/m³

Not listed

3.5mg/m³

None

Section 4. Hazardous Identification (Emergency Overview)

Developer is a black powder containing small amounts of toner, and possessing no immediate hazard.

There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner.

Section 5. Health Hazard Data

Route(s) of Entry:

Inhalation?

Skin?

Ingestion?

Possible but very unusual.

Health Hazards: Acute oral toxicity ------------LDL0 of this toner which is included in this developer is over

2,000mg/kg.

Mutagenicity ------------------ The toner, which is included in this developer, has been tested on

Ames test.The result is negative.

Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human

carcinogen). This classification is given to chemicals for which there is inadequate human

evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The

classification is based upon the development of lung tumors in rats receiving chronic inhalation

exposures to free carbon black at levels that induce particle overload of the lung. Studies

performed in animal models other than rats did not show any association between carbon

black and lung tumors.

While there have been no studies to date using developer, a two-year cancer bioassay using a

typical toner preparation containing carbon black (a small amount of toner is included in the

developer mixture) demonstrated no association between toner exposure and tumor

development in rats.

Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any

non-toxic dust.

Medical Conditions Generally Aggravated by Exposure:

Emergency and First Aid Procedures:

None

Inhalation; Remove to fresh air. If effects occur, consult medical personnel.

Eye; In case of contact, immediately flush eyes with water for 15 minutes.

Section 6. Physical Chemical Characteristics

Boiling / Melting Point: Not applicable

Specific Gravity:

about 7.3

Vapor Pressure:

Vapor Density:

Evaporation Rate:

Appearance:

Odor:

Not applicable

Fine powder

Odorless

Solubility inWater: Negligible

PH:

Not applicable

Viscosity:

Color:

Not applicable

Black

Section 7. Fire and Explosion Data

Flash Point (Method Used):

IgnitionTemperature:

Not applicable

>350°C

Flammable Limits:

(LEL); Not applicable

(UEL); Not applicable

Extinguishing Media:

Special Fire Fighting Procedure:

CO2, dry chemical, foam or water

None

Unusual Fire and Explosion Hazard: This material has no unusual fire or explosion hazards.

Sensitivity to Mechanical Impact:

Sensitivity to Static Charge:

None

Section 8. Reactivity Data

Stability:

Stable

Incompatibility (Material to Avoid):

Hazardous Decomposition:

Hazardous Polymerization:

None

CO and NOx

Will not occur.

Section 9. Precautions for Safe Handling and Use

Personal Protection Information (Respiratory, Eye Protection and Protective Glove):

None required under normal use.

Engineering Control /Ventilation:

Work / Hygienic Practice:

Not required.

Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner.

Waste Disposal Method:

Waste material may be dumped or incinerated under conditions

which meet all federal, state and local environmental regulations.

Section 10. Regulatory Information

NFPA Rating (U.S.A.):

WHMIS Legislation (Canada):

Transport Information:

UN No.:

Health = 1

Flammability = 1

This product is not a controlled product.

This product is not a hazardous material.

None allocated.

Reactivity = 0

Section 11. Other Information

References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans,

Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro Compounds, Lyon, pp-

149-261

H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie, P.

Morrow, U. Mohr, S. Takenaka, and R. Mermelstein (1991) Pulmonary Response to Toner upon

Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp. 280-299

MEMO

WARNING:

FCC Regulations state that any unauthorized changes or modifications to

this equipment not expressly approved by the manufacturer could void the

user's authority to operate this equipment.

Note:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules.These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment.This equipment gen-

erates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the operation manual, may cause harmful interfer-

ence to radio communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

NOTICE

BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WAR-

RANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to assure

you, the end-user, of warranty protection, Sharp extends a limited warranty to

each of its authorized dealers and, in turn, requires each of its authorized dealers

to extend its own warranty to you on terms that are no less favorable than those

given to the dealer by Sharp. You should be aware, however, that Sharp does not

itself extend any warranties, either express or implied, directly to you, the end-

user, and no one is authorized to make any representations or warranties on behalf

of Sharp. Specifically, SHARP DOES NOT EXTEND TO YOU, THE END-USER,

ANY EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF

MERCHANTABILITY, FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR

PURPOSE IN CONNECTION WITH THE HARDWARE, SOFTWARE OR

FIRMWARE EMBODIED IN, OR USED IN CONJUNCTION WITH THIS PROD-

UCT. Sharp is not responsible for any damages or loss, either direct, incidental or

consequential, which you, the end-user, may experience as a result of your pur-

chase or use of the hardware, software or firmware embodied in or used in con-

junction with this Product. Your sole remedy, in the event that you encounter any

difficulties with this Product, is against the authorized dealer from which you pur-

chased the Product.

AR-164 Digital Laser Copier/Printer

In the event that this authorized dealer does not honor its warranty commitments,

please contact the General Manager, Business Products Group, Sharp Electronics

Corporation, Sharp Plaza, Mahwah, NJ 07430-2135, so that Sharp can try to help

assure complete satisfaction of all the warranty rights to which you are entitled

from the authorized dealer.

AR-164

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430-2135.

www.sharp-usa.com

SHARP CORPORATION

PRINTED IN CHINA

2002B

TINSE0000QSZZ

Panasonic Cw 973fr User Manual
Samsung Avmkh020ea B 0 User Manual
Samsung Avmkh C User Manual
Samsung Aw1203b User Manual
Samsung Kh Eav User Manual
Schumacher 612a Pe User Manual
Schumacher Se 1252ma User Manual
Schumacher Sf 2254 User Manual
Subaru Robin Power Products Eh65v User Manual
Toshiba Multifunctional Digital Systems 232 User Manual