USER’S MANUAL
MH020FPEA
MH023FPEA
MH026FPEA
MH035FPEA
MH052FPEA1
Free Joint Multi Air Conditioner
(Cooling and Heating)
E S F I P D G R DB98-20234A(8)
Safety Precautions
The following safety precautions must be taken when using your air conditioner.
Risk of electric shock. • Can cause injury or death. • Disconnect all
WARNING
remote electric power supplies before servicing, installing or cleaning.
• This must be done by the manufacturer or its service agent or a similar
qualified person in order to avoid a hazard.
◆ Users of this product are cautioned not to attempt repair of this product
DURING OPERATION
at their own discretion. Instead, they are requested to directly contact a
designated service center or the outlet at which the product was
purchased.
◆ Never spill any kind of liquid into the unit. Should this happen, unplug
or main switch off the unit and contact an authorized service center.
◆ Do not insert anything between the air outlet blades because the inner
fan may be damaged and could cause injury. Keep children away from
the unit.
◆ Do not place any obstacles in front of the unit.
◆ Do not spray liquid of any kind into the indoor unit. Should this happen,
switch off the breaker used for your air conditioner and contact your
installation specialist.
◆ Make sure that the unit is correctly ventilated at all times:
Do not place clothing or other materials over it.
◆ If the wireless remote control will not be used for a long time, remove
the batteries. (If applicable)
◆ When using a wireless remote control, the distance should not be more
than 7 meters from the air conditioner. (If applicable)
◆ Before throwing out the device, it is necessary to pull back the battery
DISPOSING OF THE UNIT
cells and get rid of them safely for recycling reasons.
◆ When you need to dispose of the unit, consult your dealer. If pipes are
removed incorrectly, refrigerant may blow out and come into contact
with your skin, causing injury. Releasing refrigerant into the atmosphere
also damages the environments.
◆ Please recycle or dispose of the packaging material for this product in
an environmentally responsible manner.
◆ Never store or ship the air conditioner upside down or sideways to
OTHERS
avoid damage to the compressor.
◆ The appliance is not intended for use by young children or infirm
persons without supervision: Young children should be supervised to
ensure that they do not play with the appliance.
◆ Max current is measured according to IEC standard for safety and
current is measured according to ISO standard for energy efficiency.
E-2
Contents
◆
PREPARING YOUR AIR CONDITIONER
◆◆◆Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
◆◆◆View of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
◆◆◆Remote Control-Buttons and Display . . . . . . . . . . . . . . . . . . . . . .
◆◆◆Wired Remote Controller-Buttons and Display . . . . . . . . . . . . . . .
◆◆◆Centralized Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
4
6
7
8
◆◆◆Function Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
◆◆◆Getting Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
◆◆◆Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . 12
◆
OPERATING YOUR AIR CONDITIONER
◆◆◆Selecting the Automatic Operating Mode . . . . . . . . . . . . . . . . . . . 13
◆◆◆Cooling Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
◆◆◆Heating Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
◆◆◆Changing the Room Temperature Quickly . . . . . . . . . . . . . . . . . . 16
◆◆◆Removing Excess Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
◆◆◆Airing Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
◆◆◆Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . 19
◆◆◆Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . . . . 19
◆
◆
PROGRAMMING YOUR AIR CONDITIONER
◆◆◆Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
◆◆◆Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
◆◆◆Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
RECOMMENDATIONS FOR USE
◆◆◆Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
◆◆◆Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . 24
◆◆◆Operating Your Air Conditioner Without the Remote Control . . . . . 24
◆◆◆Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
◆◆◆Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
◆◆◆Cleaning Deodorizing and Bio Filters (Option) . . . . . . . . . . . . . . . 27
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
E-3
View of the Unit
The design and shape are subject to change according to the model.
Indoor Unit
Room temperature sensor
Air Inlet
Auto grille
On/Off switch
Air filter
(under the grille)
Remote Control Sensor
Air flow blades
(outlet)
Operation indicator
Set temperature &
room temperature
Timer indicator
Sleep Timer indicator
Fan speed setting
Note
◆ If you want to turn On/Off the Display during operation,
press the button on the remote control.
◆ The room temperature sensor senses air temperature around
the sensor, and shows the temperature on the display.
E-4
Remote Control - Buttons and Display
Operating mode
Remote control
transmission indicator
(
AUTO,
COOL,
DRY,
FAN,
HEAT)
Battery discharge indicator
Fan speed
Turbo mode
Temperature setting
Air flow direction
Sleep mode
Off Timer setting
On Timer setting
On/Off button
Temperature adjustment
buttons
Mode selection button
(AUTO, COOL, DRY, FAN, HEAT)
Digital On/Off button
Swing button
Fan speed adjustment
button
Turbo button
Timer Set/Cancel button
Sleep button
On Timer button
Off Timer button
E-6
Wired Remote Controller-Buttons and Display
The wired remote controller is an optional accessory and it is installed on the wall.
To use the wired remote controller, refer to an appropriate manual.
Operating mode
Centralized controller indicator
(In case of installing the Centralized controller)
Removing frost indicator
Communication
error indicator
Temperature setting
On Timer setting
Off Timer setting
Fan speed
Air flow direction
Filter Sign indicator
Test indicator
On/Off button
Temperature adjustment
buttons
On/Off indicator
Fan speed
adjustment button
On Timer button
Swing button
Timer Set/Cancel button
Test button
Filter Reset button
Mode selection button
Note
◆ The
button is for your installation specialist. You must NOT press it.
button. Then the wired remote
◆ After cleaning the air filter, press the
controller will display the FILTER SIGN indicator when the time to clean the air filter;
refer to page 26 or 27.
E-7
Centralized Controller
The centralized controller is an optional accessory and it is installed on the wall.
To use the centralized controller, refer to an appropriate manual.
Front View
Operating lamp
All On button
All Off button
On/Off indicators
On/Off buttons
Index
Note
◆ The operating lamp comes on even when only one air conditioner
connected to the centralized controller is operating.
E-8
Side View
Operating Mode Switch
COOL
AUTO
HEAT
Note
◆ Choose the appropriate operating mode with the Operating Mode Switch
that enables the user to choose between the Cool/Auto/Heat mode.
E-9
Function Controller
The function controller is an optional accessory and it is installed on the wall.
The function controller is an additional controller which is used with the centralized controller.
To use the function controller, refer to an appropriate manual.
Operating mode
Removing frost indicator
Centralized controller indicator
Communication
error indicator
Temperature setting
Fan speed
Room number display
Air flow direction
Test indicator
Filter Sign indicator
On/Off & Timer
Set/Cancel button
Temperature adjustment
buttons
On/Off indicator
Fan speed adjustment
button
Indoor unit
selection button
Swing button
Test button
Filter Reset button
Mode selection button
Note
◆ The
◆ After cleaning the air filter, press the
will display the FILTER SIGN indicator when the time to clean the air filter.
button is for your installation specialist. You must NOT press it.
button. Then the wired remote controller
E-10
Getting Start
You have just purchased a Free Joint Multi air conditioner and it has
been installed by your installation specialist.
Your Owner’s Instructions contains valuable information on using your
air conditioner. Please take the time to read it as it will help you take full
advantage of the unit’s features.
The booklet is organized as follows.
◆ The following figures are shown on pages from 4 to 6 :
-
-
Indoor unit
Remote control(buttons and display)
They will help you find the buttons and understand the symbols displayed.
◆ In the manual, you will find a series of step-by-step procedures for each
function available.
The illustrations in the step-by-step procedures use three different symbols:
PRESS
PUSH
HOLD DOWN
E-11
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when:
◆ You purchase the air conditioner
◆ The remote control does not work correctly
Note
◆ Use two AAA, LR03 1.5V batteries.
◆ Do not use old batteries or different kinds of batteries together.
◆ Batteries may be completely discharged after 12 months, even
◆ if they have not actually been used.
1
2
Push the battery cover on the rear of the remote control with your thumb
in the direction of the arrow and remove it.
Insert the two batteries, taking care to respect the polarities:
◆ + on the battery with + on the remote control.
◆ - on the battery with - on the remote control.
3
Close the cover by sliding it back until it clicks into place.
E-12
Selecting the Automatic Operating Mode
You can start the air conditioner in Automatic mode from your remote
control. In the Automatic mode, the optimum temperature and the fan
speed is selected automatically.
1
If necessary, press the
(On/Off) button.
Result:
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
lt will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control,
press the
appears.
button on the remote control one or more times until it
Result:
◆ The indoor unit beeps each time you press the
button.
◆ The air conditioner runs in AUTO mode.
Note
You can change modes at any time.
E-13
Cooling Your Room
You must select the Cool mode if you wish to adjust the:
◆ Cooling temperature
◆ Fan speed when cooling
1
If necessary, press the
(On/Off) button.
Result: The operation indicator on the indoor unit lights up.
◆
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
lt will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control,
press the
appears.
button on the remote control one or more times until it
Result:
◆
◆
The indoor unit beeps each time you press the
The air conditioner runs in COOL mode.
button.
Note
You can change modes at any time.
3
To adjust the temperature, press the
the required temperature is displayed.
button one or more times until
Possible temperatures are between 18°C and 30°C inclusive.
Result: Each time you press the button:
◆
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts cooling, provided that the room
temperature is higher than the selected temperature.
◆ If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan is still operating.
4
Select the fan speed by pressing the
until the required setting is displayed:
button one or more times
)
Automatic (rotated :
Low
Medium
High
Result:
Each time you press the
beeps.
button, the indoor unit
5
To control the direction of the air flow, refer to page 19.
E-14
Heating Your Room
You must select the Heat mode if you wish to adjust the:
◆ Heating temperature
◆ Fan speed when heating
1
If necessary, press the
(On/Off) button.
Result: The operation indicator on the indoor unit lights up.
◆
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
IMPORTANT
◆ Plugged in
◆ Stopped
It will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control, press the
button on the remote control one or more times until it appears.
Result:
◆
◆
The indoor unit beeps each time you press the
The air conditioner runs in HEAT mode.
button.
Note
You can change modes at any time.
3
To adjust the temperature, press the
button one or more times
until the required temperature is displayed.
Possible temperatures are between 16°C and 30°C inclusive.
Result: ◆ Each time you press the button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts heating, provided that the room
temperature is lower than the desired temperature
(selected temperature+3°C).
◆ If the room temperature reaches the set temperature, the air
conditioner stops heating, but the fan is still operating.
4
Select the fan speed by pressing the
until the required setting is displayed:
button one or more times
)
Automatic (rotated :
Low
Medium
High
Result:
◆
◆
Each time you press the
button, the indoor unit beeps.
For the first 3 to 5 minutes, the fan operates very
slowly until the air has been sufficiently warmed. Once the
correct temperature has been reached, the fan is automatically
set to the required speed.
5
To control the direction of the air flow, refer to page 19.
E-15
Changing the Room Temperature Quickly
The Turbo cooling/heating function is used to cool or heat your room as
quickly as possible.
For example : You have just come home and find that the room is very
hot. You wish to cool it down as quickly as possible.
The Turbo function operates for 30 minutes with the maximum settings before
returning automatically to the mode and temperature previously selected.
1
If necessary, press the
(On/Off) button.
Result:
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
2
Press the
Result:
button.
◆ The temperature and fan settings are adjusted automatically.
◆ The air conditioner cools or heats the room as quickly as possible.
◆ After 30 minutes, the air conditioner is reset automatically to the
previous mode, temperature and fan settings.
But, if you press the
button in DRY or FAN mode,
it will change to AUTO mode automatically.
3
If you wish to stop the Turbo function before the end of the 30-minute period,
press the
button again.
Result:
The air conditioner is reset automatically to the previous mode,
temperature and fan settings.
4
To control the direction of the air flow, refer to page 19.
E-16
Removing Excess Humidity
If the atmosphere in your room is very humid or damp, you can
remove excess humidity without lowering the room temperature too
much.
1
If necessary, press the
(On/Off) button.
Result: The operation indicator on the indoor unit lights up.
◆
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
It will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control, press the
button on the remote control one or more times until it appears.
Result:
◆
◆
The indoor unit beeps each time you press the
The air conditioner runs in DRY mode.
button.
Note
You can change modes at any time.
3
To adjust the temperature, press the
button one or more times
until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result: ◆ Each time you press the button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts removing the excess humidity;
the quantity of air is adjusted automatically.
4
To control the direction of the air flow, refer to page 19.
E-17
Airing Your Room
If the atmosphere in your room is stale, you can air the room using
the Fan feature.
1
If necessary, press the
(On/Off) button.
Result:
◆
The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
2
If the
is not displayed at the top of the remote control,
press the
appears.
button on the remote control one or more times until it
Result:
◆
◆
◆
The indoor unit beeps each time you press the
The air conditioner runs in FAN mode.
The temperature is set automatically.
button.
Note
You can change modes at any time.
3
Select the fan speed by pressing the
until the required setting is displayed:
button one or more times
Low
Medium
High
Result: Each time you press the
button, the indoor unit beeps.
4
To control the direction of the air flow, refer to page 19.
E-18
Adjusting the Air Flow Direction Vertically
Depending on the position of the indoor unit on the wall of your room,
you can adjust the position of the outer air flow blade on the bottom
of the unit, thus increasing the efficiency of the air conditioner.
1
Press the
button one or more times as required.
Result: The outer blade is adjusted vertically.
RECOMMENDATION
When...
Adjust the blade to face...
Cooling
Heating
Upwards.
Downwards.
2
If you want the blade to move up and down automatically when the air
conditioner is operating, press the
button.
Result: The blade moves up and down, around the base position set.
3
To stop the blade moving up and down, press the
button again.
Note
If you switch the air conditioner... Then the blade is...
Off
Closed completely.
Set to the initial position powered.
On again
Adjusting the Air Flow Direction Horizontally
There are two sets of inner air flow blades. Just as the outer air flow
blade can be adjusted vertically, the inner blades can be adjusted
horizontally.
1
Adjust each set of inner blades to the required position, by pushing or
pulling them sideways.
E-19
Setting the On Timer
The On Timer enables you to switch on the air conditioner automatically
after a given period of time. You can set the period of time from
30 minutes to 24 hours.
1
To set the operating time, press the
button one or more times until
the required time is displayed. Possible time is between 0.5 hour and 24
hours inclusive.
2
Press the
(Set/Cancel) button to complete the setting.
Result: ◆ The remaining time is displayed.
◆ Blinking of the timer indicator stops.
◆ The selected mode and the temperature on the display
disappear after 10 seconds.
◆ The air conditioner will switch on automatically when the
counter displayed on the remote control reaches the set time
and disappears the On timer setting.
3
To select an operating mode in advance, press the
button until the
desired mode is displayed at the top of the remote control.
Result: ◆ The air conditioner will run in the selected mode when it is
turned on.
To Cancel the On Timer
Press the
(Set/Cancel) button.
Note
◆ If you press the
button when the Off Timer is set,
the Off Timer is also cancelled.
E-20
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner automatically
after a given period of time. You can set the period of time from
30 minutes to 24 hours.
1
To set the operating time, press the
button one or more times until
the required time is displayed. Possible time is between 0.5 hour and 24
hours inclusive.
2
Press the
(Set/Cancel) button to complete the setting.
Result: ◆ The remaining time is displayed.
◆ Blinking of the timer indicator stops.
◆ The air conditioner will switch off automatically when the
counter displayed on the remote control reaches the set time
and disappears the Off timer setting.
Example If you would like to turn the air conditioner on after 2 hours
and to operate it for 2 hours:
1. Press the
2. Press the
3. Press the
4. Press the
button until ‘2.0 Hr’ is displayed.
(Set/Cancel) button.
button until ‘4.0 Hr’ is displayed.
(Set/Cancel) button.
Note
You can see or change the setting mode and/or the temperature
by pressing the
Off timer.
button or the
button after setting the
To Cancel the Off Timer
Press the
(Set/Cancel) button.
Note
◆ If you press the
button when the On Timer is set,
the On Timer is also cancelled.
E-21
Setting the Sleep Timer
The Sleep Timer can be used when you are cooling or heating your
room to switch the air conditioner off automatically after a period of
6 hours.
Note
If you wish to switch the unit off at a specific time, refer to
page 21.
1
2
Make sure that you have selected either COOL or HEAT mode.
Press the button.
Result: ◆ The indoor unit beeps.
◆ The air conditioner will be controlled as indicated in the
illustrations below.
Cooling The desired temperature is
increased by 1°C every hour.
When it has been increased
by 2°C (after 2 hours), the
temperature is maintained for
4 hours.
Heating The desired temperature is
decreased by 1°C every hour.
When it has been decreased
by 2°C (after 2 hours), the
temperature is maintained for
4 hours.
To Cancel the Sleep Timer
If you no longer wish to use the Sleep Timer that you have set, you
can cancel it at any time.
Press the
Result:
button.
◆
◆
◆
The indoor unit beeps.
The
is no longer displayed.
The air conditioner operates normally.
E-22
Operating Recommendations
Here are a few recommendations that you should follow when using
your air conditioner.
Topic
Recommendation
Heating performances
The heat pump inside the air conditioner
absorbs heat from outside air and brings it
indoors. If the temperature of the outside air
drops, the air conditioner will heat less. If you
find that the room is not warm enough, use an
additional heating appliance.
Warm air circulation
The air conditioner circulates warm air to heat
your room; as a result, some time will be
required after starting the air conditioner to
warm the entire room. If necessary, set the
air conditioner on before you wish to use
the room.
Frost
When outside temperatures are low and
humidity is high, frost may form in the outdoor
unit when heating is selected.
If this happens:
◆ The heating operation is stopped.
◆ The Defrost mode is triggered automatically
for about 10 minutes.
No intervention is required from you; after
about 10 minutes, the air conditioner starts
operating again normally.
High indoor and outdoor If both the indoor and outdoor temperatures
temperatures
are high and you select the Heat mode, the
outdoor unit’s fan and compressor may stop
at times. This is normal; simply wait until the
air conditioner switches on again.
Power failure
If a power failure occurs when the air conditioner
is operating, the unit is switched off.
When the power returns, the air conditioner starts
up again automatically.
E-23
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges within which the air conditioner can be used.
If the air conditioner is used at...
Then...
High temperatures
The automatic protection feature may be triggered and the air conditioner stopped.
Low temperatures
A water leak or some other malfunction may occur if the heat exchanger freezes.
Water may condense on and drip from the surface of the indoor unit if it is used for long periods.
High humidity levels
Mode
Outdoor Temperature
Indoor Temperature
Indoor Humidity
Heating
Cooling
Drying
-15°C to 24°C approx.
-5°C to 43°C approx.
5°C to 43°C approx.
27°C or less
21°C to 32°C approx.
18°C to 32°C approx.
-
80% or less
-
❇
The standardized temperature for heating is 7°C. If the outdoor temperature drops to 0°C or below,
the heating capacity can be reduced depending on the temperature condition.
If the cooling operation is used at over 32°C(indoor temperature) then, it does not cool at its full capacity.
Operating Your Air Conditioner Without the Remote Control
Your air conditioner can be operated directly from the indoor unit if
the remote control is lost or broken.
1
2
Slide the lower front grille down.
To switch the air conditioner on, press the On/Off switch on the right
side of the indoor unit.
Result: N The Operation indicator on the indoor unit comes on.
N The indoor unit beeps.
N The air conditioner starts up in the most suitable mode for
the room temperature:
Room Temperature
Less than 21°C
21°C or above
Operating Mode
Heat
Cool
3
To switch the air conditioner off, press the On/Off switch again.
Note
Even if the air conditioner has been switched on via the
On/Off switch, operations can still be controlled using the
remote control as usual.
E-24
Solving Common Problems
Before contacting the after-sales service, perform the following simple checks.
They may save you the time and expense of an unnecessary call.
Problem
Explanation/Solution
The air conditioner does not
operate at all
◆ Check that the breaker used for the air conditioner is switched on.
◆ Check that the operation indicator on the indoor unit is on;
if necessary press the
(On/Off) button on the remote control.
◆ Check whether the TIMER indicator on the indoor unit is switched on.
If so:
- Wait until the switch-on time is reached and the air conditioner starts
up automatically
- Cancel the timer (see pages 20 and 21 for further details)
The air conditioner does not
operate with the remote control
◆ Check that there are no obstacles between you and the indoor unit.
◆ Check the remote control batteries.
◆ Check that you are close enough to the indoor unit
(7 meters/yards or less).
No beep is heard when you press
◆ Check that you are pointing the remote control at the remote control
sensor in the right of the indoor unit.
the
(On/Off) on the remote
control
◆ Replace the remote control batteries if necessary.
The air conditioner does not cool
or heat
◆ Check that the correct operating mode has been selected (AUTO,
COOL, HEAT).
◆ The room temperature may be too low or too high.
◆ Dust may be blocking the air filter guard; refer to page 26 for cleaning
instructions.
◆ Check that there is no obstacle in front of the outdoor unit.
When heating, the required room
temperature is never reached and
the air conditioner frequently stops
◆ Check that the required temperature has been set correctly.
◆ Increase the fan speed.
◆ If the air flow is directed upwards, use the remote control to direct it
downwards.
The fan speed does not change
◆ Check that the operating mode is set to COOL, HEAT or FAN;
in the AUTO mode, the fan speed changes automatically and in
the DRY mode, it is set to AUTO.
when you press the
button
The air flow direction does not
change when you press the
button
◆ Check that the air conditioner has been switched on; if necessary,
press the
(On/Off) button on the remote control.
The timer is not correctly triggered
◆ Check that the timer has been programmed correctly;
see pages 20 and 21.
Odour is permeated in the room
during air conditioning
◆ Air the room.
E-25
Cleaning Your Air Conditioner
For the best use of your air conditioner, you must clean it every
2 weeks regularly to remove the dust that accumulates on the air filter.
Before cleaning your air conditioner, ensure that you
have switched off the breaker used for the unit.
IMPORTANT
1
2
Slide the lower front grille down.
Slide the upper front grille up slightly, then open the grille by pulling right
and left sides of the grille.
3
4
Disassemble the upper front grille by opening the grille completely.
Lift out the bottom edge of the air filters and pull down to release them.
Grille support
5
6
Remove all dust on the air filters with a vacuum cleaner or brush.
When you have finished, insert the top part of the filters into their slot
and push down on the bottom edge until they click into place.
7
8
Clean the front grille with a damp cloth and mild detergent (do NOT use
benzene, solvents or other chemicals).
Body groove
Lower
front
grille
Fix the left side of grille support, then insert the right side of grille support.
Hook
Note ◆◆ If you have not used the air conditioner for a long period of time,
set the fan going for 3 to 4 hours to dry the inside of the air conditioner
thoroughly.
◆◆To close the upper front grille completely after cleaning filters, turn on
and turn off the air conditioner.
E-26
Cleaning Deodorizing and Bio Filters (Option)
To remove minute dust particles and odors, deodorizing and Bio filters
are installed in the air conditioner.
You should clean the filters every 3 months.
MH020FPEA/MH023FPEA/MH026FPEA/
MH035FPEA
1
2
3
4
Open the upper front grille by pulling right and left sides of the grille.
Pull out the deodorizing and Bio filters.
Deodorizing Filter
Bio Filter
Wash the filters with clean water, then dry them in the shade.
Insert the filters into the original position.
MH052FPEA1
Note
You can change the position of filters with each other.
Bio Filter
5
Close the front grille.
Deodorizing Filter
E-27
Contact SAMSUNG WORLD WIDE
If you have any comments or questions regarding a Samsung product, contact the SAMSUNG customer care center.
Country
Customer Care Center
Web Site
BELGIUM
02 201 2418
844 000 844
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka
Vyskočilova 4, 14000 Praha 4
CZECH REPUBLIC
DENMARK
FINLAND
70 70 19 70
030-6227 515
3260 SAMSUNG
08 25 08 65 65 ( 0,15/min)
FRANCE
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
01805 - 121213 ( 0,14/min)
06-80-SAMSUNG (7267864)
800-SAMSUNG (7267864)
0032 (0)2 201 24 18
0900 20 200 88 ( 0,10/min)
815-56 480
0 801 801 881
80 8 200 128
0800-SAMSUNG (7267864)
902 10 11 30
0771-400 200
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
REPUBLIC OF IRELAND
SWITZERLAND
RUSSIA
0870 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG (7267864)
8-800-200-0400
KAZAHSTAN
UZBEKISTAN
UKRAINE
LITHUANIA
LATVIA
8-800-080-1188
8-800-120-0400
8-800-502-0000
8-800-77777
800-7267
800-7267
ESTONIA
C Samsung Electronics Co., Ltd. All Rights Reserved.
|