PurePac
Electronic Air Purification System
PB1900-0604
filtration.Optional TechSorb High Mass Zero Dust
bonded activated carbon is available for gas
phase/odor control, making PurePac the IDEAL
SOLUTION for quality indoor air.
General
The Flanders-Precisionaire PurePac Electronic Air
Purification System is designed for reliable, high effi-
ciency air filtration required in today's commercial
building environments. It is available in both side
access housings and front access units, for use with
air handlers and central ventilation systems.
Configuration
PurePac Side Access units are available in sizes
ranging from 3,000 to 30,000 cfm. Housings are 16
gauge galvanealed steel, continuously welded,
primed and painted. Pre and post mist eliminators,
electronic collectors and built-in cleaning system are
factory assembled into the housing. PLC control and
detergent dispenser are supplied as separate compo-
nents.
PurePac is a new generation electronic air purifier,
incorporating highly dependable high frequency elec-
tronics that deliver the specified efficiency instantly
and continuously. The extremely low resistance to air-
flow means less fan horsepower is needed, compared
to conventional media filters, and because the resist-
ance is constant, the system air volume is always
maintained. Permanent aluminum collectors, built-in
automatic cleaning and a low 35 watts per 1,000 cfm
energy usage, result in a substantially lower life cycle
cost, compared to conventional air filtration systems.
PurePac front access units are available in sizes rang-
ing from 12,000 to unlimited cfm. Pre and post mist
eliminators, electronic collector modules, built-in
cleaning system, Unistrut‚ framing, PLC control and
detergent dispenser are furnished as built-up sub-
assemblies
High performance and low operating cost make Pure
Pac an excellent choice for HVAC system
Key Features
• Reliable high frequency electronics do not use fragile ion-
izing wires or insulators
Side Access
• Specified ASHRAE 52.1-92 efficiency is instant and con-
stant
• Resistance to airflow is a low 0.25î w.g., resulting in
reduced fan horsepower
• Constant resistance to airflow prevents fluctuations in sys-
tem air volume
• Permanent aluminum collector modules never need
replacing
• Built-in automatic cleaning and PLC controls
• Optional TechSorb bonded carbon for gas/odor control
• Available in side access housings or front access units
• Rugged design lasts the life of a HVAC system
• Interfaces with Building Management System
Front Access
Flanders Precisionaire - Foremost in Air Filtration
Engineered Products: 1-800-637-2803 Replacement Products: 1-800-347-2220
PurePac Delivers
charging and collecting stages. This assures that all
available floor space, up to 30% in some instances.
system air is filtered.
PurePac's low resistance to airflow results in reduced
fan horsepower and fan energy cost. Over a period of
time, this reduction amounts to significant savings in
energy costs. Since PurePac uses wash-in-place
electronic collectors, replacement filter cost, disposal
cost and labor cost are eliminated.
Conventional media filters rely on fiber density for par-
ticulate removal efficiency. A media filter is rated effi-
ciency is based on the average efficiency over the fil-
ter is life. Since the initial filter efficiency is lower than
the rated efficiency, a substantial amount of particles
go unfiltered. In contrast, PurePac delivers the rated
efficiency instantly and continuously. The high-densi-
ty charging and collecting zones produce an immedi-
ate and constant removal rate regardless of particle
size.
When it comes to value, PurePac delivers. High per-
formance and reliability in a compact design, and low
operating cost make PurePac the ideal choice for
today's IAQ challenges. Call us, and we'll prepare a
life cycle cost comparison for your filtration system
and show you how PurePac can deliver performance,
reliability and value.
System Description
PurePac Front Access Model (FA) is packaged as a
complete system, including the electronic air purifier,
system control, detergent dispenser and system
accessories. Components are furnished factory
assembled, except for the electronic air purifier, which
is shipped knocked-down for field installation inside
the air handler or ventilation duct.
PurePac Model FA uses Flanders type HCC electron-
ic collectors and modular design, arranged in multiple
tiers and varying widths to attain the specified capac-
ities and efficiency. The versatile design and modular
construction can accommodate all sizes of ventilation
systems by installing multiple units side-by-side.
Reliability
The PurePac uses a programmable logic controller
(PLC) for system control and monitoring, in conjunc-
tion with high frequency electronics, to deliver opti-
mum performance and assure the highest degree of
reliability.
The versatile control system can be easily integrated
with existing building management systems, adding
another degree of reliability in the overall building sys-
tem.
The durable, all aluminum 2-stage electronic collec-
tors feature unitary construction and are designed to
last the lifetime of the system. The integrated auto-
matic wash system assures optimum performance
and maximum system reliability.
Value
PurePac's design features increased collector surface
area in a smaller package compared to conventional
systems, resulting in higher dirt holding capacities and
reduced system footprint. This translates into extra
Flanders Precisionaire - Foremost in Air Filtration
Engineered Products: 1-800-637-2803 Replacement Products: 1-800-347-2220
PurePac Front Access Units
PLC Control automatic
or manual operation.
30 Gallon Detergent
Dispenser liquid level sen-
sor and flow control valve.
Model FA-0604 (metal mesh
prefilters removed)
System Accessories
solenoid valve, backflow preventer, Y-
strainer and ball valve.
Options
Utilities
PurePac is available with TechSorb HMZD bonded,
activated carbon panels for gas phase contaminant
and odor control. Since the granules are locked
together, TechSorb eliminates settling, dusting, and air
by-pass, which are typical in loose granular carbon fil-
ters.
Electrical
Standard: 120 Vac, 1 ph, 60 Hz
Optional: 208-230, 460 Vac, 1 ph, 50/60 Hz
Wash Water:(See Selection Table) gpm @ 40 psig
TechSorb is furnished in disposable panels, eliminat-
ing the messy chore of emptying and refilling loose
carbon holding frames.
System Drain: Sized according to applicable codes
to handle water and detergent volume shown in Size
Selection Table
TechSorb is impregnated with select enhancers, mak-
ing it an extremely effective sorbent media for
formaldehyde and other gas contaminants present in
new or remodeled buildings.
System Accessories
Each PurePac Front Access system is furnished with the
following standard accessories.
Wash water strainer
Ball valve.
1 each
1 each
1 each
1 each
2 each
55 gal
Backflow preventer
Solenoid valve
Access door electrical interlock & pilot light.
Detergent
Flanders Precisionaire - Foremost in Air Filtration
Engineered Products: 1-800-637-2803 Replacement Products: 1-800-347-2220
PurePac Front Access Units
Model Number Development
Unit Selection Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front
Access
Nominal
Height
Nominal
Width
1. From the Size Selection Table below, select the Model
FA with Air Volume and Dimensions that meet the
required efficiency.
FA
06
06
2. Multiple Model FA units of the same height may be
grouped together to create larger, multi-section units.
Represents a PurePac Front Access unit, model
FA0606, nominally 6 feet high by 6 feet wide, as illus-
trated below.
3. Each Model FA is shipped complete with the System
Accessories as shown on Page 4.
Front Elevation
Side Elevation
Air Volume (cfm)
Dimensions (3)Wash Cycle
Face
Area(ft2)
(1,2)Efficiency
90%
Overall (in)
H
Water
gpm
Detergent (4)Wt.
Model
95%
85%
W
gal
28.8
36
(lb)
FA-0604
FA-0605
FA-0606
FA-0804
FA-0805
FA-0806
FA-1004
FA-1005
FA-1006
FA-1204
FA-1205
FA-1206
22.8
28.32
33.84
30.4
10,000
12,500
15,000
13,500
16,500
20,000
16,500
21,000
25,000
20,000
25,000
30,000
12,500
15,500
18,000
16,500
20,500
24,500
20,500
25,500
30,500
24,500
30,500
36,500
14,000
17,500
21,000
18,500
23,000
27,500
23,500
29,000
34,500
28,000
35,000
41,500
77 3/8
77 3/8
50 3/8
61 3/16
72
1.4
1.8
2.2
1.9
2.4
2.9
2.4
3
1,025
1,160
1,295
1,250
1,540
1,740
1,610
1,830
2,055
1,900
2,165
2,430
77 3/8
43.2
38.4
48
102 5/8
102 5/8
102 5/8
127 7/8
127 7/8
127 7/8
153 1/8
153 1/8
153 1/8
50 3/8
61 3/16
72
37.76
45.12
38
57.6
48
50 3/8
61 3/16
72
47.2
60
56.4
72
3.6
2.9
3.6
4.3
45.6
50 3/8
61 3/16
72
57.6
72
56.64
67.68
86.4
Flanders Precisionaire - Foremost in Air Filtration
Engineered Products: 1-800-637-2803 Replacement Products: 1-800-347-2220
PurePac Side Access Units
PLC Control automatic
or manual operation.
30 Gallon Detergent
Dispenser liquid level sen-
sor and flow control valve.
Conforms to ANSI/UL
STD 867 for Electrostatic
Air Cleaners
System Accessories
Model FA-0604 (metal mesh
solenoid valve, backflow preventer, Y-
strainer and ball valve.
prefilters removed)
System Description
System Accessories
PurePac Side Access Model (SA) is a factory pack-
aged system including the side access housing, wash
system, electronic collectors, control system, deter-
gent dispenser, and accessories. The factory assem-
bled system is designed for installation in air handlers
and ventilation systems.
Each PurePac Side Access system is furnished with
the following standard accessories.
Wash water strainer..........................................1 each
Ball valve..........................................................1 each
Backflow preventer...........................................1 each
Solenoid valve.................................................1 each
Detergent..........................................................55 gal
The side access cabinet features unitary construction
with flanges on the upstream and downstream sides
to bolt in-line with new or existing air handling sys-
tems. The cabinet is furnished complete with pre and
post mist eliminators, electronic collectors, integral
wash system and electrically interlocked access door.
Utilities
Electrical
Options
PurePac Model (SA) is available with TechSorb
HMZD, bonded, activated carbon panels for gas
phase control. The TechSorb is contained in a sepa-
rate cabinet that conveniently bolts to the exhaust side
of the Model SA cabinet. The panels are arranged in
a V Bank configuration using fully gasketed tracks to
eliminate air by-pass.
Standard: 120 Vac, 1 Ph, 60 Hz
Optional: 208-230, 460 Vac, 1 Ph, 50/60 H
Wash Water: (See Selection Table) gpm @ 40 psig
System Drain: Integral 3î FNPT
Agency Approval
Each PurePac Side Access system is ETL listed, con-
forming to ANSI/UL 867 Standard for Electrostatic Air
Cleaners
Flanders Precisionaire - Foremost in Air Filtration
Engineered Products: 1-800-637-2803 Replacement Products: 1-800-347-2220
PurePac Side Access Units
Model Number Development
Unit Selection Guide
1. From the Size Selection Table below, select the Model
SA with Air Volume and Dimensions that meet the
required efficiency.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side
Nominal
Height
Nominal
Width
Access
2. Multiple Model SA units of the same height may be
arranged side-by-side to create a larger, multi-section
unit. Specify one unit with left hand and one unit with
right hand access doors.
SA
02
03
Represents a PurePac Front Access unit, Model
SA0203, nominally 2 feet high x 3 feet wide, as illus-
trated below.
3. Each Model SA is shipped complete with the System
Accessories shown on Page 6.
Inlet Elevation
Access Side Elevation
Air Volume (cfm)
(1,2)Efficiency
90%
Dimensions (in)
Overall Inlet/Outlet
(3) Wash Cycle
Water Detergent
gpm gal (lb)
Face
(4) Weight
Model
Area(ft2)
95%
85%
A
B
C
SA-0203
SA-0204
SA-0205
SA-0206
SA-0403
5.6
7.6
2,500
3,500
3,000
4,000
3,500
4,500
40 1/4
40 1/4
40 1/4
40 1/4
64 1/8
64 1/8
64 1/8
64 1/8
64 1/8
64 1/8
64 1/8
88
41 7/8 31 1/2
54 3/8 31 1/2
65 1/8 31 1/2
7.2
9.6
0.4
0.5
0.6
0.7
0.7
1
510
570
9.4
4,000
5,000
6,000
12
650
11.3
11.3
5,000
6,000
7,000
76
31 1/2
14.4
14.4
19.2
24
785
5,000
6,000
7,000
41 7/8 55 3/8
54 3/8 55 3/8
65 1/8 55 3/8
710
SA-0404 15.2
SA-0405 18.9
SA-0406 22.6
SA-0407 26.4
6,500
8,000
9,500
810
8,500
10,000
12,000
14,500
16,000
18,500
9,000
11,500
14,000
16,500
18,500
21,000
10,500
14,000
17,500
21,000
24,500
27,500
31,000
1.2
1.4
1.7
1.9
2.2
1.1
1.4
1.8
2.2
2.5
2.9
3.2
930
10,000
11,500
13,000
15,000
7,500
76
55 3/8
28.8
33.6
38.4
43.2
21.6
28.8
36
1,110
1,225
1,335
1,445
860
88 5/8 55 3/8
99 3/8 55 3/8
110 1/8 55 3/8
41 7/8 79 1/4
54 3/8 79 1/4
65 1/8 79 1/4
SA-0408
30
SA-0409 33.8
SA-0603 16.9
SA-0604 22.8
SA-0605 28.3
SA-0606 33.8
SA-0607 39.6
10,000
12,500
15,000
17,500
20,000
22,000
12,500
15,500
18,500
21,500
24,500
27,500
88
1,100
1,180
1,315
1,500
1,685
1,860
88
88
76
79 1/4
43.2
50.4
57.6
64.8
88
88 5/8 79 1/4
99 3/8 79 1/4
110 1/8 79 1/4
SA-0608
45
88
SA-0609 50.8
88
(1) ASHRAE 52.1-92 Test Standard
(2) Capacities may be rounded to nearest 500 cfm
(3) Based on 40psi water pressure
(4) Total system net weight
Flanders Precisionaire - Foremost in Air Filtration
Engineered Products: 1-800-637-2803 Replacement Products: 1-800-347-2220
Engineering Specifications
A. General
The electronic air cleaner shall be the two stage,
manifolds containing brass spray nozzles, located
on both the air entering and air leaving side of each
module tier. Complete, effective washing of all ion-
izing-collector cell surfaces and all appurtenances
shall be provided. Drive motors, used to oscillate
the manifolds, shall be high torque, gear reduced,
totally enclosed fan cooled type, and be perma-
nently lubricated. Drive linkage shall be a rigid,
positively fastened type without tracks or sprock-
ets.
dual voltage, plate type electrostatic precipitator,
sized to clean the airflow capacities scheduled on
the Contract Documents at an efficiency of at least
(specify %) as determined by the ASHRAE
Standard 52.1-92, Dust Spot Test Method. Air
cleaner shall be furnished with built-in high pres-
sure, low volume water/detergent washing system
and programmable logic control for complete auto-
matic operation.
One detergent dispensing assembly shall be pro-
vided to serve each electronic air cleaner. The
detergent dispenser shall consist of a (specify 30
or 55) gallon anti-corrosive reservoir, positive dis-
placement pump, motor, and flow volume control
valve.
B. Configuration (Select B.1or B.2)
B.1 The electronic air cleaner shall be furnished in a
side access housing, fabricated from 16 gage gal-
vanealed steel, continuously welded, primed and
painted. The housing shall be furnished with gas-
keted, hinged access door with safety electrical
interlock, flanged inlet/outlet collars, built-in clean-
ing system and sloped bottom drain pan. The
housing shall be tracked for and furnished with alu-
minum pre and post mist eliminators and ionizing-
collecting cells.
Solenoid valve, strainer, backflow preventer, ball
valve, and an initial supply of detergent shall be fur-
nished by the electronic air cleaner manufacturer.
E. Control and High Voltage Power Supplies
Each electronic air cleaner shall use a single
remote-mounted control and power supply, con-
tained in NEMA 12 enclosures. The unit shall oper-
ate on 120 Vac, 1Ph, 60 Hz.
B.2 The electronic air cleaner shall be front/rear
access, furnished using prefabricated, galvanized
framework designed to contain ionizing-collecting
cells and wash system. All frame sub-assemblies
shall be match marked and prepared for bolted
field assembly. Base support framework shall be
stainless steel. All necessary fasteners and fittings
shall be furnished. Framing shall be designed for
cell removal either upstream or downstream and
pre-punched air by-pass baffles shall be provided
for the upstream side. The foundation supporting
the framework, including drains and specified
opening shall be prepared by the Contractor in
accordance with the manufacturer's recommenda-
tion and written instructions.
The control shall be of the programmable logic
(PLC) type, furnished in a NEMA 12 enclosure,
preprogrammed to sequence the electronic air
cleaner through wash cycles at a schedule to be
determined with the Owner. Integral electronic
time clock with manual override shall be provided.
High voltage power supply, furnished in a NEMA 12
enclosure, shall be the high frequency, solid state
type, supplying a dual voltage and current output
specified by the electronic air cleaner manufactur-
er. Power supply shall have a regulated input and
output for line fluctuations of 10% and shall have a
current limiting shutdown and restart feature.
C. Electronic Collector Modules
The face panel of the enclosures shall contain indi-
cators for electronic air cleaner control status (run,
wash, etc.), individual power supply, primary circuit
indicating light, monitoring instrumentation, and on-
off switch.
Ionizing-collecting cells shall be of industrial design
integrity and single unit construction. The cells
shall be all aluminum construction except the ioniz-
ing electrode shall be of the rigid stainless steel
type without serrated spikes or the tungsten wire
type. Repelling and collecting plates shall be pos-
itively retained in place using tie rod and tubular
spacer design. High voltage insulators shall be
molded from structural, self-glazing ceramic; shall
contain no appurtenances; shall be of radial and
bilateral symmetry; shall contain no high voltage
penetrations and shall not contact the high voltage
on the process air side. The entire assembly shall
be suitable for handling cold saturated air.
Provide enable/disable contacts suitable for inter-
face with the specified Building Control and
Management System (BMS).
F. Electrical Interlocks
Furnish duct door electrical interlocks, disconnect
switch, and pilot light assembly. All access to elec-
tronic air cleaners and high voltage power packs
shall contain electrical safety interlocks which de-
energize the primary power circuit prior to access-
ing high voltage.
D. Built-in Cleaning System
Water/detergent washing system shall be high
pressure, low volume type. Detergent, wash and
rinse water shall be applied by oscillating copper
Flanders Precisionaire - Foremost in Air Filtration
Engineered Products: 1-800-637-2803 Replacement Products: 1-800-347-2220
|