Operating Instructions
Multi-Function Printer
Model No.
KX-MB2000HX
KX-MB2010HX
KX-MB2025EX
KX-MB2025FX
KX-MB2030EX
KX-MB2030FX
This pictured model is KX-MB2000.
Do NOT connect the unit to a computer with the USB cable until prompted to do so during the setup
of Multi-Function Station (CD-ROM).
1
2
KX-MB2025/KX-MB2030 only:
R This unit is compatible with Caller ID. You must subscribe to the appropriate service offered by
your service provider/telephone company.
KX-MB2025EX/KX-MB2030EX only:
R Designed to be used in Czech, Hungary and Slovakia according to the location setting feature. The
default setting is Czech. To change the location setting, see page 58 (feature #114).
Important Information
Note:
For your safety
Laser radiation
R The area near the output tray (B) may also get warm.
This is normal.
CLASS 1 LASER PRODUCT
The printer of this unit utilises a laser. Use
of controls or adjustments or performance
of procedures other than those specified
herein may result in hazardous radiation
exposure.
A
Laser diode properties
Laser output : Max. 15 mW
Wavelength : 760 nm – 800 nm
Emission duration : Continuous
LED light
CLASS 1 LED PRODUCT
B
Do not view directly with optical
instruments.
For best performance
Toner cartridge and drum cartridge
R When replacing the toner cartridge or drum cartridge,
do not allow dust, water, or liquids to come in contact
with the drum. This may affect print quality.
R For optimal performance, genuine Panasonic toner
cartridges and drum cartridges are recommended.
We cannot be responsible for problems that may be
caused by a non-Panasonic toner cartridge or drum
cartridge:
LED light of CIS properties
LED radiation output : Max. 1 mW
Wavelength :
Red 630 nm typ.
Green 520 nm typ.
Blue 465 nm typ.
–
–
–
Damage to the unit
Poor print quality
Improper operation
Emission duration : Continuous
Fuser unit
Toner cartridge
During or immediately after printing, the
fuser unit (A) gets hot. This is normal. Do
not touch the fuser unit.
R Do not leave the toner cartridge out of the protective
bag for a long time. It will decrease the toner life.
Drum cartridge
installation of the drum cartridge. After you have read
them, open the drum cartridge protective bag. The
drum cartridge contains a photosensitive drum.
Exposing it to light may damage the drum. Once you
have opened the protective bag:
–
Do not expose the drum cartridge to light for more
than 5 minutes.
–
–
Do not touch or scratch the black drum surface.
Do not place the drum cartridge near dust or dirt,
or in a high humidity area.
–
Do not expose the drum cartridge to direct
sunlight.
R To extend the life of the drum cartridge, the power
switch should never be turned OFF immediately after
3
Important Information
printing. Leave the power turned ON for a minimum
of 30 minutes after printing.
Moving the unit
When moving the unit, hold by the grips (A) on both
Location
sides.
R To avoid malfunction, do not position the unit near
appliances such as TVs or speakers which generate
an intense magnetic field.
Static electricity
R To prevent static electricity damage to the interface
connectors or other electrical components inside the
unit, touch a grounded metal surface before touching
the components.
Environment
R Keep the unit away from electrical noise generating
devices, such as fluorescent lamps and motors.
R The unit should be kept free from dust, high
A
temperature and vibration.
R The unit should not be exposed to direct sunlight.
R Do not place heavy objects on top of the unit. When
you leave the unit unused for a long period of time,
unplug this unit from the power outlet.
R The unit should be kept away from heat sources such
as heaters, kitchen stoves, etc. Damp basements
should also be avoided.
A
R During the printing process, heat is used to fuse toner
onto the page. As a result, it is normal for the machine
to produce an odour during and shortly after printing.
Be sure to use this unit in an area with proper
ventilation.
Illegal copies
R It is unlawful to make copies of certain
documents.
R Do not cover slots or openings on the unit. Inspect
the air circulation vents regularly and remove any
dust build-up with a vacuum cleaner (A).
Copying certain documents may be illegal in your
country. Penalties of fines and/or imprisonment may
be imposed on those found guilty. The following are
examples of items that may be illegal to copy in your
country.
–
–
–
–
–
Currency
Bank notes and cheques
Bank and government bonds and securities
Passports and identification cards
Copyright material or trademarks without the
consent of the owner
A
–
Postage stamps and other negotiable
instruments
This list is not inclusive and no liability is
assumed for either its completeness or accuracy.
In case of doubt, contact your legal counsel.
A
Notice:
R Install your machine near a supervised area to
prevent illegal copies from being made.
Routine care
R Wipe the outer surface of the unit with a soft cloth. Do
not use benzine, thinner, or any abrasive powder.
4
Table of Contents
6
1. Introduction and Installation
J
L
K
Handset
Handset cord
1.1 Supplied accessories
1. . Introduction and Installation
A
Toner cartridge
(starter)
B
Drum cartridge
M
One-touch dial
label (page 43)
Handset cradle
C
CD-ROM
D
Operating
instructions
(English only)
*1 Prints about 500 pages at ISO/IEC 19752 standard
page.
*2 KX-MB2000HX/KX-MB2010HX/KX-MB2025EX/
KX-MB2030EX only
*3 KX-MB2025/KX-MB2030 only
E
Important information guide
(English only)
Note:
R Save the original carton and packing materials for
(Czech, Hungarian
and Slovak only)
future shipping and transportation of the unit.
R After unpacking the product, take care of the packing
materials and/or power plug cap appropriately.
1.2 Accessory information
To ensure that the unit operates properly, we
recommend the use of Panasonic toner and drum
cartridges.
F
Quick installation
guide
G
Output tray
n Replacement accessory
–
Toner cartridge
R Model No. (Part No.): KX-FAT411E
R Prints about 2,000 pages at ISO/IEC 19752
standard page.
–
Drum cartridge
R Model No. (Part No.): KX-FAD412E
Note:
H
Power cord
I
Telephone line
cord
R ISO/IEC 19752 standard is as follows:
–
–
Environment: 23 ± 2 °C / 50 ± 10% RH
Print mode: Continuous printing
7
1. Introduction and Installation
MMenuN
1.3 Button descriptions
R To start or exit programming.
MStopN
ABCDEFGHIJ
K
L
R To stop an operation or programming session.
R To erase a character/number.
MLowerN (KX-MB2025/KX-MB2030 only)
R To select station 4–6 for the one-touch dial
MFax Auto AnswerN (KX-MB2025/KX-MB2030
only)
MNOP Q R S
T U V
W
R To turn the auto answer setting ON/OFF
* The pictured model is KX-MB2025/KX-MB2030.
MFaxN (KX-MB2025/KX-MB2030 only)
MCopyN
Station keys (KX-MB2025/KX-MB2030 only)
MRedialNMPauseN (KX-MB2025/KX-MB2030 only)
MManual BroadN (KX-MB2025/KX-MB2030 only)
R To send a document to multiple parties by using
R To redial the last number dialled. If the line is busy
when you make a phone call using the
MMonitorN button, or when you send a fax, the
unit will automatically redial the number 2 or more
times.
MBroadcastN (KX-MB2025/KX-MB2030 only)
R To send a document to multiple parties
MScanN
R To insert a pause during dialling.
MFlashN (KX-MB2025/KX-MB2030 only)
MCopy SizeN
R To access special telephone services or for
transferring extension calls.
MPhonebookN (KX-MB2025/KX-MB2030 only)
MMonitorN (KX-MB2025/KX-MB2030 only)
R To initiate dialling.
For beep sounds (KX-MB2000/KX-MB2010 only)
R Key beeps etc. will be heard.
When you press MMonitorN while receiving a call,
you will be able to hear the other party, but the
other party will not be able to hear you.
MContrastN
Navigator key
R To select desired settings.
R To select the contrast when sending a fax
R To adjust the volume (KX-MB2025/KX-MB2030
(KX-MB2025/KX-MB2030 only) (page 42).
R To search for a stored item (KX-MB2025/
MResolutionN
R To select the resolution when copying
MSetN
R To select the resolution when sending a fax
R To store a setting during programming.
MToneN (KX-MB2025/KX-MB2030 only)
(KX-MB2025/KX-MB2030 only) (page 42).
MZoomN
R To change from pulse to tone temporarily during
R To enlarge or reduce a document when copying
dialling when your line has rotary/pulse service.
MQuick ScanN (KX-MB2025/KX-MB2030 only)
R To store a scanned document into memory, and
MStartN
R To send a fax (KX-MB2025/KX-MB2030 only)
MPage LayoutN
R To make copies using various page layouts
MCaller IDN (KX-MB2025/KX-MB2030 only)
8
1. Introduction and Installation
Document guides (KX-MB2010/KX-MB2025/
KX-MB2030 only)
1.4 Overview
Document cover
1.4.1 Front view
Power switch
Output tray
A
B C
D E
Document entrance (KX-MB2010/KX-MB2025/
KX-MB2030 only)
Paper input tray
Recording paper exit
Document exit (KX-MB2010/KX-MB2025/
KX-MB2030 only)
Speaker (KX-MB2025/KX-MB2030 only)
Handset unit connection jack (KX-MB2025/
KX-MB2030 only)
1.4.2 Rear view
F
G H
I
J
K
A
B
C
L
* The pictured model is KX-MB2025.
A
D E
D
E F G H
* The pictured model is KX-MB2030.
Recording paper guides
LED (KX-MB2000/KX-MB2010/KX-MB2030 only)
LAN interface connector (KX-MB2000/
KX-MB2010/KX-MB2030 only)
R 10Base-T/100Base-TX
Power inlet
Manual input tray (Rear cover)
External telephone jack (KX-MB2025/KX-MB2030
only)
F
H I
* The pictured model is KX-MB2000.
Telephone line jack (KX-MB2025/KX-MB2030
only)
Top cover
ADF (Automatic Document Feeder) cover
(KX-MB2010/KX-MB2025/KX-MB2030 only)
USB interface connector
9
1. Introduction and Installation
3 Place the toner cartridge (C) into the drum cartridge
1.5 Toner cartridge and drum
cartridge
(D) vertically.
C
The supplied toner cartridge is a starter toner cartridge.
Caution:
R Read the following instructions before you begin
installation. After you have read them, open the
drum cartridge protective bag. The drum
cartridge contains a photosensitive drum.
Exposing it to light may damage the drum. Once
you have opened the protective bag:
–
–
–
–
Do not expose the drum cartridge to light for
more than 5 minutes.
Do not touch or scratch the black drum
surface inside of the drum cartridge.
Do not place the drum cartridge near dust or
dirt, or in a high humidity area.
Do not expose the drum cartridge to direct
sunlight.
D
4 Press down the toner cartridge firmly (E). Keep
pressing while turning the green lever on each side
of the toner cartridge towards you (F).
R Do not leave the toner cartridge out of the
protective bag for a long time. It will decrease the
toner life.
R We cannot be responsible for any damage to the
unit or degradation of print quality which may
occur from the use of a non-Panasonic toner and
drum cartridges.
E
E
F
F
R Do not add toner to the toner cartridge.
1 Before opening the protective bag of the new toner
cartridge, shake it vertically more than 5 times.
5 Make sure that the arrows (G) match, to install the
toner cartridge correctly.
G
2 Remove the toner cartridge and drum cartridge from
the protective bags. Peel off the seal (A) from the
toner cartridge.
R Do not touch or scratch the black drum surface
(B).
A
B
10
1. Introduction and Installation
6 Open the top cover (H) by holding the indentations
7 Install the drum and toner cartridge (L) by holding
(I) on both sides of the unit.
the tabs.
J
H
I
L
I
Note:
R Make sure that the arrows (M) match, to install
the drum and toner cartridge correctly.
R Do not touch the transfer roller (J).
R If the lower glass (K) is dirty, clean it with a soft
and dry cloth.
K
M
11
1. Introduction and Installation
poor or “REPLACE DRUM” appears on the display,
replace the toner cartridge and drum cartridge.
8 Close the top cover by holding the indentations on
both sides of the unit, until locked.
R To ensure that the unit operates properly, we
recommend the use of Panasonic toner and drum
cartridges. See page 7 for accessory information.
R To maintain print quality and machine life, we
recommend you to clean slots and openings
when replacing the toner cartridge and/or drum
cartridge.
life.
Waste disposal method
Waste material should be disposed of under conditions
which meet all national and local environmental
regulations.
Toner save feature
If you want to reduce toner consumption, set the toner
toner cartridge will last approximately 20 % longer. This
feature may lower the print quality.
Caution:
R To prevent injuries, be careful not to put your
hands under the top cover.
When to replace the toner cartridge and the drum
cartridge
When the display shows the following, replace the toner
cartridge.
–
“TONER LOW”
–
“TONER EMPTY”
Note:
R To check the drum life and quality, please print the
information on the drum life. If printing quality is still
12
1. Introduction and Installation
vary depending on the usage environment). Remove
the printed paper before the output tray becomes full.
1.6 Output tray
Insert the output tray extender (A) until it clicks into
place, and then press the centre part (B) of the extender
to open it.
If the top part of the extender is detached
1. With the top part of the extender in the open position,
insert the tab (A) into the left hole (B) of the
extender.
A
B
A
2. Slide the other tab (C) into the right hole (D) of the
extender from below until it clicks into place.
B
D
C
Note:
R Do not place the unit in an area where the output tray
may be easily bumped into.
R The output tray can hold up to approximately 100
sheets of printed paper (the number of sheets may
13
1. Introduction and Installation
1 Pull the paper input tray (A) until it clicks into place,
then pull it completely out, lifting the front part of the
tray.
1.7 Recording paper
The paper input tray unit can hold:
2
2
–
–
–
Up to 250 sheets of 60 g/m to 75 g/m paper.
2
Up to 230 sheets of 80 g/m paper.
2
Up to 200 sheets of 90 g/m paper.
R A4, letter, B5 and 16K-size paper can be used. B5
and 16K-size paper can only be used when using the
unit for printing or copying.
paper.
R The unit is set for printing A4-size plain paper by
default.
–
To use other paper sizes, change the
recording paper size setting (feature #380 on
A
–
To use thin paper, change the recording paper
2 Before loading a stack of paper, fan the paper to
Note for recording paper:
prevent paper jams.
R We recommend that you test paper (especially
special sizes and types of paper) on the unit before
purchasing large quantities.
R Do not use the following types of paper:
–
Paper with cotton and/or fibre content that is over
20 %, such as letterhead paper or paper used for
resumes
–
Extremely smooth or shiny paper, or paper that is
highly textured
–
–
Coated, damaged or wrinkled paper
Paper with foreign objects attached, such as tabs
or staples
–
–
Paper that has dust, lint or oil stains
Paper that will melt, vaporize, discolour, scorch
or emit dangerous fumes near 200 °C, such as
vellum paper. These materials may transfer onto
the fusing roller and cause damage.
3 Load the paper, print-side up (B).
Important:
R Push down to lock the plate (C) in the paper
–
–
Moist paper
Inkjet paper
input tray, if necessary.
R Some paper is designed to be printed on only one
side. Try printing on the other side of the paper if you
are not happy with the print quality, or if misfeeding
occurs.
B
R For proper paper feeding and best print quality, we
recommend using long-grained paper.
R Do not use paper of different types or thicknesses at
the same time. This may cause paper jams.
R Avoid double-sided printing.
R Do not use paper printed from this unit for
double-sided printing with other copiers or printers.
This may cause paper jams.
R To avoid curling, do not open paper packs until you
are ready to use the paper. Store unused paper in the
original packaging, in a cool and dry location.
C
R For customers who live in high humidity areas:
Please be sure to store paper in an air-conditioned
room at all times. If you print using moist paper, it may
cause paper jam.
4 Adjust the recording paper guides. Pinch the front
side of the recording paper guide (D), then slide it to
14
1. Introduction and Installation
match the paper size mark. Pinch the right side of the
recording paper guide (E), then slide it to adjust the
width to the size of the recording paper.
Caution for the paper input tray
R Do not drop the paper input tray.
R Make sure that the recording paper is under the
paper limit mark (F), and the paper should not
be loaded over the snubbers (G).
F
R Hold the paper input tray with both hands when
removing or installing. The paper input tray
weighs approximately 2 kg when fully loaded with
recording paper.
E
G
D
5 Insert the paper input tray into the unit, lifting the front
part of the tray. Then push it completely into the unit.
Approx. 2 kg
1.7.1 Manual input tray
You can use the manual input tray for printing with the
computer and for copying. It can hold one page at a time.
When printing or copying multiple pages, add a next
page after the first page has been fed into the unit.
paper.
R The unit is set for printing A4-size plain paper by
default.
–
To use other paper sizes, change the
recording paper size setting (feature #381 on
–
To use thin paper, change the recording paper
Note:
1 Adjust the width of the guides (A) to the size of the
R If the paper is not loaded correctly, re-adjust the
recording paper.
paper guides, or the paper may jam.
R If the paper input tray does not close, the plate in the
paper input tray may not be in the locked position.
Push the paper down and make sure that the paper
is laying flat in the paper input tray.
15
1. Introduction and Installation
2 Insert the paper, print-side down (B) until the unit
grasps the paper and a single beep is heard.
B
A
Note:
R To print from the manual input tray;
–
when printing with the computer, select #2 for the
printer properties.
–
when making a copy, set the copy input tray
setting to “#2” beforehand (feature #460 on
If these settings are not changed, when printing or
copying multiple pages, the 1st page will be printed
from the manual input tray, but the rest of the pages
will be printed from the paper input tray.
R If the paper is not inserted correctly, re-adjust the
paper, or the paper may jam.
16
2. Preparation
LAN cable (not supplied)
2.1 Connections
Caution:
R To assure continued emission limit compliance,
use only shielded LAN cable (category 5 straight
cable).
2. . Preparation
R When you operate this product, the power outlet
*1 KX-MB2025/KX-MB2030 only
should be near the product and easily accessible.
*2 KX-MB2000/KX-MB2010/KX-MB2030 only
R Be sure to use the telephone line cord supplied
with this unit (KX-MB2025/KX-MB2030 only).
R Do not extend the telephone line cord
IMPORTANT NOTICE FOR THE USB
CONNECTION
(KX-MB2025/KX-MB2030 only).
R DO NOT CONNECT THE UNIT TO A
COMPUTER WITH THE USB CABLE UNTIL
PROMPTED TO DO SO DURING THE SETUP
OF MULTI-FUNCTION STATION (page 25).
Important:
Note:
R Do not place any objects within 10 cm of the right, left
and back sides of the unit.
R If any other device is connected to the same
telephone line, this unit may disturb the network
condition of the device (KX-MB2025/KX-MB2030
only).
R If you use the unit with a computer and your internet
provider instructs you to install a filter (H), please
connect it as follows (KX-MB2025/KX-MB2030 only).
C
A
B
D
G
E
F
* The pictured model is KX-MB2030.
Power cord
H
R Connect to a power outlet
(220–240 V, 50/60 Hz).
* The pictured model is KX-MB2030.
Telephone line cord
Designed to be used in Czech, Hungary and
Slovakia according to the location setting feature
(KX-MB2025EX/KX-MB2030EX only).
R Connect to a single telephone line jack.
[EXT] jack
The default setting is Czech. To change the location
R You can connect an answering machine or an
extension telephone. Remove the stopper if
attached.
Using network router/network hub (KX-MB2000/
KX-MB2010/KX-MB2030 only)
Answering machine (not supplied)
R We recommend using network routers/network hubs
(F) under secure network environments. Consult
your network administrator for firewall settings, etc.
To the Internet
Network router/Network hub (not supplied)
R The warranty does not cover damage due to security
R Also connect networked computers.
problems or any inconveniences relating to it.
17
2. Preparation
2.2 Turning the power switch ON 2.3 Dialling mode (KX-MB2025/
Turn the power switch to the ON position (A).
KX-MB2030 only)
If you cannot dial (page 42), change this setting
according to your telephone line service.
A
MMenuN
MSetN
1
MMenuN
2 Press MBNM1NM2NM0N to display “DIALLING MODE”.
3 Press M1N or M2N to select the desired setting.
M1N “PULSE”: For rotary/pulse dial service.
M2N “TONE” (default): For tone dial service.
4
MSetN
5 Press MMenuN to exit.
18
2. Preparation
2.4 Selecting the operation mode 2.5 Setting the original
(Scan/Copy) (Fax: KX-MB2025/
2.5.1 Using the scanner glass
KX-MB2030 only)
You can select the desired mode by pressing one of the
following buttons.
A
KX-MB2000
KX-MB2010
KX-MB2025
KX-MB2030
B
–
–
–
MScanN: Select this mode when using the unit as a
MCopyN: Select this mode when using the unit as a
MFaxN (KX-MB2025/KX-MB2030 only): Select this
mode when using the unit as a fax machine
1 Open the document cover (A).
2 Place the document FACE DOWN on the scanner
glass (B), aligning the top left of the document with
the corner where the
mark is positioned.
3 Close the document cover.
Note:
Note:
R The default operation mode is the copy mode.
R Confirm that there are no documents in the automatic
document feeder (KX-MB2010/KX-MB2025/
KX-MB2030 only).
R You can change the default operation mode (feature
the default operation mode (feature #464 on
R Place the original onto the scanner glass gently. To
avoid malfunction, do not press down too firmly.
R If the original is a thick book, do not close the
document cover.
R Confirm that any ink, paste or correction fluid has
dried completely.
R Effective scanning area is shown by the shaded area:
Effective scanning area
4 mm
208 mm
4 mm
4 mm
289 mm
4 mm
19
2. Preparation
Minimum document size
2.5.2 Using the automatic document feeder
(KX-MB2010/KX-MB2025/KX-MB2030 only)
A
128 mm
Maximum document size
216 mm
* The pictured model is KX-MB2010.
1 Insert the document (up to 20 pages) FACE UP into
Effective scanning area
the feeder until a single beep is heard.
2 Adjust the width of the document guides (A) to fit the
actual size of the document.
4 mm
Note:
R Confirm that there are no documents on the scanner
glass.
R Confirm that any ink, paste or correction fluid has
dried completely.
R Remove clips, staples or other fasteners.
R Do not insert the following types of documents (Make
a copy of the document using the scanner glass and
set the copy instead.):
4 mm
4 mm
4 mm
208 mm
216 mm
–
Chemically treated paper such as carbon or
carbonless duplicating paper
R Shaded area will be scanned.
–
–
–
–
Electrostatically charged paper
Badly curled, creased or torn paper
Paper with a coated surface
Paper with printing on the opposite side that can
be seen through the other side, such as newsprint
the selected paper size.
Document weight
R Single sheet:
R The total height of the documents when laid flat, must
be less than 4 mm. If the documents exceed the
capacity of the automatic document feeder, they may
fall or cause a jam in the feeder.
2
2
2
60 g/m to 80 g/m
R Multiple sheets:
2
60 g/m to 80 g/m
R To set a document with a width of less than 210 mm,
we recommend using the scanner glass to copy the
original document onto A4 or letter-size paper, then
setting the copied document for better results.
R Do not set documents that do not satisfy the
requirements of size and weight. Make a copy of the
document using the scanner glass and set the copy.
R Available document size, document weight and
effective scanning area are as follows:
20
2. Preparation
2.6 Help function (KX-MB2025/
KX-MB2030 only)
2.7 Adjusting the volume
(KX-MB2025/KX-MB2030 only)
The unit contains helpful information, which can be
printed for reference.
Important:
R Before adjusting the volume, set the operation
mode to fax mode. If the MFaxN light is OFF, turn
it ON by pressing MFaxN.
–
–
–
–
–
–
–
“BASIC SETTINGS”
“FEATURE LIST”
“PHONEBOOK”
“FAX RECEIVING”
“COPIER”
“REPORTS”
“CALLER ID”
MFaxN
MSetN MCNMDN
MMenuN
Ringer volume
While the unit is idle, press MCN or MDN.
To turn the ringer OFF
Press MCN repeatedly to display “RINGER OFF= OK?”.
A MSetN
MSetN MFNMEN
R The unit will not ring.
R To turn the ringer back ON, press MDN.
1 Press MMenuN repeatedly to display “HELP”.
2 Press MFN or MEN repeatedly to display the desired
Monitor volume
item. A MSetN
While using the monitor, press MCN or MDN.
3 Press MMenuN to exit.
21
2. Preparation
R To use this feature, make sure the time adjustment
2.8 Date and time
We recommend you to set the date and time. The other
party will receive your unit’s date and time as the header
information.
R If the time has not previously been set, Caller ID will
not adjust the clock.
MMenuN
MFaxN
MSetN MFNMEN
* The pictured model is KX-MB2025/KX-MB2030.
MMenuN A MBNM1NM0NM1N A MSetN
1
2 Enter the current date/month/year by selecting 2
digits for each.
Example: 3 August, 2010
M0NM3N M0NM8N M1NM0N
3 Enter the current hour/minute by selecting 2 digits for
each.
Example: 10:15 PM (12 hour clock format)
1. M1NM0N M1NM5N
2. Press MGN repeatedly to select “PM”.
Press MGN repeatedly to select “AM” or “PM”, or
24-hour time entry.
4
MSetN
5 Press MMenuN to exit.
Note:
R To check the current date and time setting, press
MFaxN to temporarily change the unit to the fax mode
(KX-MB2025/KX-MB2030 only).
R Your unit’s date and time will be used as the header
information for the following:
–
When sending as an attached file to an email
destination directly from this unit (Scan to email
address) (page 32) (KX-MB2000/KX-MB2010/
KX-MB2030 only).
–
KX-MB2030 only).
R If the date and time is not set correctly, the other party
will receive an incorrect date and time as their
header. This may confuse the other party.
To correct a mistake
Press MFN or MEN to move the cursor to the incorrect
number, and make the correction.
If you have subscribed to a Caller ID service
(KX-MB2025/KX-MB2030 only)
The date and time will be automatically set according to
the received caller information.
22
2. Preparation
2.9 Your logo (KX-MB2025/
KX-MB2030 only)
2.10 Your fax number
(KX-MB2025/KX-MB2030 only)
You can program your logo (name, company name, etc.)
You can program your fax number so that it appears on
so that it appears on the top of each page sent.
the top of each page sent.
MMenuN
MStopN
MMenuN
MStopN
MSetN MFNMEN
MFlashN MSetN MFNMEN
1
MMenuN A MBNM1NM0NM2N A MSetN
1
MMenuN A MBNM1NM0NM3N A MSetN
2 Enter your fax number, up to 20 digits.
R To enter a “+”, press MGN.
for character entry). A MSetN
R To enter a space, press MBN.
R To enter a hyphen, press MFlashN.
R To erase a number, press MStopN.
3 Press MMenuN to exit.
To correct a mistake
Press MFN or MEN to move the cursor to the incorrect
character, and make the correction.
R To erase all characters, press and hold MStopN.
3
MSetN
4 Press MMenuN to exit.
To correct a mistake
Press MFN or MEN to move the cursor to the incorrect
number, and make the correction.
R To erase all numbers, press and hold MStopN.
23
2. Preparation
For the subnet mask:
2.11 Configuring the unit to
access the LAN (KX-MB2000/
KX-MB2010/KX-MB2030 only)
You can print documents, scan documents, receive
faxes or send faxes (KX-MB2030 only) using a computer
connected to the LAN. To enable these features, you
need to set the IP address, subnet mask, and default
gateway in the unit.
1. Press M5NM0NM2N to display “SUBNET MASK”.
A MSetN
2. Enter the subnet mask of the network. A MSetN
For the default gateway:
1. Press M5NM0NM3N to display “DEFAULT
GATEWAY”. A MSetN
2. Enter the default gateway of the network. A
MSetN
Important:
5 Press MMenuN to exit.
R Consult your network administrator when setting
the IP address, subnet mask, and default
gateway.
6 Install Multi-Function Station on the computer that
To correct a mistake in the IP address, subnet mask,
or default gateway
2.11.1 Setting up automatically with a DHCP
server
Press MFN or MEN to move the cursor to the incorrect
number, and make the correction.
Your situation:
–
When only one unit is connected to the LAN.
2.11.3 Setting the computer for PC fax
reception (KX-MB2030 only)
If your network administrator manages the network with
a DHCP (Dynamic Host Configuration Protocol) server,
it will automatically assign an IP (Internet Protocol)
address, subnet mask, and default gateway to the unit.
You need to select the computer that will be used for
receiving faxes.
1 After connecting the LAN cable to the unit and the
computer, turn the power switch ON.
Important:
R Make sure the PC fax setting is set to “ALWAYS”
or “CONNECTED” beforehand (feature #442 on
R The IP address, subnet mask, and default
gateway will be set automatically.
2 Install Multi-Function Station on the computer that
R Make sure the fax preview mode is turned OFF
Note:
1
MMenuN A MBNM4NM4NM3N A MSetN
R You can connect two or more units and assign IP
addresses automatically with a DHCP server, but we
recommend assigning static IP addresses manually
for each unit to avoid network access and
configuration troubles.
2 Press MCN or MDN repeatedly to select the desired
computer. A MSetN
3 Press MMenuN to exit.
Note:
R If the unit is not connected to the LAN, the computer
connected to the unit by USB is assigned as the
default computer for PC fax reception.
2.11.2 Setting up manually
Your situation:
–
When your network administrator does not manage
the network with a DHCP server.
R To select the desired computer easily, change the PC
name beforehand (page 27).
–
When two or more units are connected to the LAN.
You need to assign an IP address, subnet mask, and
default gateway manually.
1
MMenuN
2 Press MBNM5NM0NM0N to display “DHCP”.
3 Press M0N to select “DISABLED”. A MSetN
4 Set each item.
For the IP address:
1. Press M5NM0NM1N to display “IP ADDRESS”. A
MSetN
2. Enter the IP address of the unit. A MSetN
24
2. Preparation
Install KB835732 from Microsoft download
site before installing Easy Print Utility.
Windows XP Service Pack 2 or later.
2.12 Installing Multi-Function
Station
–
Note:
R A USB cable is not supplied. Please purchase a
2.12.1 Required computer environment
shielded Type-A male/Type-B male USB cable.
Panasonic Multi-Function Station software enables the
unit to carry out the following functions:
2.12.2 Installing Multi-Function Station on a
computer
–
–
Printing on plain paper, thin paper and labels
Previewing documents and changing printer settings
before printing (Easy Print Utility)
R Install Multi-Function Station (CD-ROM) before
connecting the unit to a computer with the USB
cable. If the unit is connected to a computer with
the USB cable before installing Multi-Function
Station, the [Found New Hardware Wizard]
dialogue box will appear. Click [Cancel] to close
it.
R The screenshots shown in these instructions are
for Windows XP and are included for reference
only.
–
–
Scanning documents and converting an image into
text with Readiris OCR software
®
Scanning from other applications for Microsoft
®
Windows that support TWAIN scanning and WIA
®
scanning (Windows XP/Windows Vista , USB
connection only)
–
Storing, editing or erasing items in directories using
your computer (KX-MB2025/KX-MB2030 only)
–
–
Programming the features using your computer
Sending, receiving fax documents using your
computer (KX-MB2025/KX-MB2030 only)
R The screenshots shown in these instructions
may differ slightly from those of the actual
product.
To use Multi-Function Station on your computer, the
following are required:
Operating System:
R Software features and appearance are subject to
change without notice.
R If you are also using KX-MB200/KX-MB700/
Windows 2000/Windows XP/Windows Vista
CPU:
1 Start Windows and exit all other applications.
R You must be logged in as an administrator in
order to install Multi-Function Station.
®
Windows 2000: Pentium P or higher processor
Windows XP: Pentium Q or higher processor
Windows Vista: Pentium 4 or higher processor
RAM:
Windows 2000/Windows XP: 128 MB (256 MB or more
recommended)
2 Insert the supplied CD-ROM into your CD-ROM
drive.
R If the [Select Language] dialogue box appears,
select the language that you want to use with this
software. Click [OK].
Windows Vista: 512 MB (1,024 MB or more
recommended)
R If the installation does not start automatically:
Click [Start]. Choose [Run...]. Type “D:\Install”
(where “D” is the drive letter of your CD-ROM
drive). Click [OK].
Other Hardware:
CD-ROM drive
Hard disk drive with at least 200 MB of available space
USB interface
LAN interface (10Base-T/100Base-TX) (KX-MB2000/
KX-MB2010/KX-MB2030 only)
Other:
(If you are not sure what the drive letter is for your
CD-ROM drive, use Windows Explorer and look
for the CD-ROM drive.)
3 [Easy Installation]
®
Internet Explorer 5.0 or later (KX-MB2000/KX-MB2010/
R The installation will start automatically.
KX-MB2030 only)
4 When the setup program starts, follow the on-screen
instructions.
Warning:
R To assure continued emission limit compliance;
–
use only shielded USB cable (Example:
Hi-Speed USB 2.0 certified cable).
–
use only shielded LAN cable (category 5
straight cable) (KX-MB2000/KX-MB2010/
KX-MB2030 only).
5 The [Connect Type] dialogue box appears.
For USB connection:
R To protect the unit, use only shielded USB cable
in areas where thunderstorms occur.
R To use Easy Print Utility on your computer, the
1. [Connect directly with a USB cable.] A [Next]
R The [Connect Device] dialogue box will appear.
following are required:
–
Windows 2000 Service Pack 4 and Security
update for Windows 2000 (KB835732).
25
2. Preparation
2. Connect the unit to a computer with the USB cable
2. Click [Operating Instructions], then follow the
on-screen instructions to view or install the operating
instructions in PDF format.
(A), then click [Next].
®
®
R Adobe Reader is required to view the operating
instructions.
Note:
R If the screen prompts you to insert the CD-ROM for
the operating system when installing Multi-Function
Station, insert it into your CD-ROM drive.
R If you install the operating instructions, you can view
it anytime by clicking [ ] on the Multi-Function
Station launcher.
A
To use another unit with the computer
You need to add the printer driver for each unit, as
follows.
* The pictured model is KX-MB2030.
R If the unit is connected to your computer, the
model name will be automatically detected.
1. Start Windows and insert the supplied CD-ROM into
your CD-ROM drive.
R You can change the name of the unit if necessary.
2. [Modify] A [Add Multi-Function Station Driver].
3. Click [Install], then follow the on-screen instructions.
Then follow the on-screen instructions.
R The files will be copied to your computer.
Note:
For LAN connection (KX-MB2000/KX-MB2010/
KX-MB2030 only):
R You cannot connect more than one unit to the same
computer at the same time (USB connection only).
1. [Connect via the Network.] A [Next]
R The [Select a Network Device] dialogue box will
appear.
To modify the software (To add or uninstall each
component)
You can select the components to install or uninstall
anytime after the installation.
2. Check [Select in the searched list] and select the
unit from the list.
You must be logged in as an administrator in order to
modify Multi-Function Station.
R If the name of the desired unit is not displayed on
the list, and the IP address for the unit has been
assigned, check [Direct input] and enter the IP
address.
1. Start Windows and insert the supplied CD-ROM into
your CD-ROM drive.
3. [Next]
2. [Modify] A [Modify Utilities]. Then follow the
R You can change the name of the unit if necessary.
on-screen instructions.
4. Click [Install], then follow the on-screen instructions.
To uninstall the software
R The files will be copied to your computer.
You must be logged in as an administrator in order to
uninstall Multi-Function Station.
Important notice
If you are using Windows XP or Windows Vista, a
message may appear after connecting the unit with
the USB cable. This is normal and the software will
not cause any difficulties with your operating system.
You can continue the installation with no problem.
This kind of message is displayed:
[Start] A [All Programs] or [Programs] A
[Panasonic] A the unit’s name A [Uninstall]. Then
follow the on-screen instructions.
R For Windows XP users
“The software you are installing for this hardware
has not passed Windows Logo testing to verify its
compatibility with Windows XP.”
R For Windows Vista users
“Would you like to install this device software?”
To view or install the operating instructions data
1. Start Windows and insert the supplied CD-ROM into
your CD-ROM drive.
26
2. Preparation
[
]
2.13 Starting Multi-Function
Station
[Start] A [All Programs] or [Programs] A
[Panasonic] A the unit’s name A [Multi-Function
Station]
R For detailed instructions on Multi-Function Station.
R To view operating instructions.
[
]
R To display usage tips.
[
]
R Multi-Function Station will appear.
R To display information about Multi-Function Station.
Note:
R You can confirm if the unit is connected to your
computer by using Device Monitor (page 76).
R Computer features (printing, scanning, etc.) may not
function properly in the following situations:
–
–
–
When the unit is connected to a computer that
was custom-built by the user.
When the unit is connected to the computer via a
PCI card or other expansion card.
When the unit is connected to another piece of
hardware (such as a USB hub or interface
adapter) and not connected directly to the
computer.
To change the settings
You can change the settings for Multi-Function Station
beforehand.
* The pictured model is KX-MB2025/KX-MB2030.
1. Select [Settings] from Multi-Function Station.
R To scan and display the scanned images.
R To scan and create an image file.
R To scan and send by email.
2. Click the desired tab and change the settings. A
[OK]
[General]
R To scan and convert an image into editable text data.
–
[Launcher display setting]: To select the display
[PC FAX] (KX-MB2025/KX-MB2030 only)
type of the launcher.
R To send a document created on the computer as a
R To display a fax document received on the computer
–
–
[OCR Path]: To select the OCR software.
[PC name list up on device] (KX-MB2000/
KX-MB2010/KX-MB2030, LAN connection only): To
select whether or not your computer name is
displayed on the unit.
[PC name] (KX-MB2000/KX-MB2010/KX-MB2030,
LAN connection only): The computer name that will
be displayed on the unit.
–
R To program the features.
R To store, edit or erase items in directories.
R To view items in the journal report or Caller ID list.
[Scan]
R To store caller information into directories.
–
[Save to]: To select the folder where the scanned
image will be saved.
R To store or erase items for broadcast transmission.
*1 KX-MB2025/KX-MB2030 only
–
[Viewer][File][Email][OCR][Custom]: To change
scanning settings for Multi-Function scan application.
[Utilities]
Note:
connection only).
R Assign a unique name for the [PC name] to avoid
errors, or the scanned image may be sent to the
incorrect computer.
To select the default Email software
The default Email software is used when
You can select the default Email software as follows.
R To change the general settings.
R To change the settings for scanning.
27
2. Preparation
For Windows 2000:
1. [Start] A [Settings] A [Control Panel] A
[Internet Options] A [Programs] A [E-mail]
2. Select the desired MAPI-compliant Email software
such as [Outlook Express], etc. A [OK]
For Windows XP:
1. [Start] A [Control Panel] A [Internet Options]
A [Programs] A [E-mail]
2. Select the desired MAPI-compliant Email software
such as [Outlook Express], etc. A [OK]
For Windows Vista:
1. [Start] A [Control Panel] A [Internet Options]
A [Programs] A [Set programs] A [Set
program access and computer defaults]
R If the [User Account Control] dialogue box
appears, click [Continue].
2. [Custom]
3. Select the desired MAPI-compliant Email software
such as [Windows Mail], etc. from [Choose a
default e-mail program]. A [OK]
28
3. Printer
Setting the printer properties
3.1 Printing from Windows
applications
You can print a file created in a Windows application. For
example, to print from WordPad, proceed as follows:
You can change the printer setting in step 3. We
recommend that you test paper (especially special sizes
and types of paper) on the unit before purchasing large
quantities.
You can change or display the settings on the following
tabs.
3. . Printer
1 Open the document you want to print.
[Basic]: Paper size, media type, pages per sheet, etc.
[Output]: Number of prints, collate, etc.
[Quality]: Quality, contrast, toner save feature, etc.
[Effects]: Watermark, overlay.
[Profile]: Saving the desired settings, selecting the
saved settings, etc.
2 Select [Print...] from the [File] menu.
R The [Print] dialogue box will appear.
For details about the [Print] dialogue box, click
[?], then click the desired item.
[Support]: Version information.
Note:
R Select the desired media type on the [Basic] tab
according to the recording paper.
Recording paper type
Plain paper
Media type
[Plain Paper]
2
2
75 g/m to 90 g/m
Thin paper
[Thin Paper]
[Label]
2
2
64 g/m to 75 g/m
Label
* The pictured model is KX-MB2025/KX-MB2030.
R When printing from a computer, the printer properties
setting overrides the following unit’s programming
features:
Note:
®
R For Microsoft PowerPoint , select [Color] or
–
Media type setting (feature #383 and feature
remove the check next to [Grayscale] in the print
dialogue so that coloured or grey objects will be
printed in greyscale properly.
–
Toner save setting (feature #482 on page 61)
To print on labels
3 Select the unit’s name as the active printer.
R If you have changed the name of the unit when
installing, select that name from the list.
You can print not only on plain paper but also on special
media (labels).
R To change the printer settings, proceed as
follows.
paper.
Use labels designed for laser printing. We recommend
the following:
For Windows 2000:
Click the desired tab and change the printer
settings.
For Windows XP/Windows Vista:
Click [Preferences], then click the desired tab.
Change the printer settings, then click [OK].
®
Avery
5160/5161/5162/5163/5164/5165/5167/5168
®
XEROX
4 Click [Print].
LWH100/LWH110/LWH120/LWH130/LWH140
R Use the manual input tray to print labels.
R Load label sheets one page at a time for printing,
print-side down.
R Remove each label after printing.
R Do not use the following types of labels:
R The unit will start printing.
Note:
R For details about the paper specifications, see
–
Labels that are wrinkled, damaged or separated
from the backing sheet.
Any sheet of labels that has spaces in it where
some of the labels have been removed.
R If a printing error occurs, the Device Monitor
error information.
–
29
3. Printer
–
Labels that do not completely cover the backing
sheet as follows:
6 Click [Print] icon on the print toolbar.
R The unit will start printing.
3.2.1 Ecology printing features
You can use various printing features and preview the
print image without test print.
Printer settings
You can change or display the settings on the following
[Basic]: Paper size, layout printing
[Output]: Number of prints, paper source, media type
[Quality]: Colour mode, toner save
[Effects]: Header, watermark, footer
3.2 Easy Print Utility
By printing using the Panasonic Easy Print Utility instead
of the printer driver, you can use useful printing features
for your convenience.
Combining multiple documents
You can display multiple pages created in various
applications and handle it as a single document.
–
Preventing unnecessary prints by checking the
preview on PC screen
–
–
Combining multiple documents
Saving a file in PDF format
2. Open another document you want to add to Easy
Print Utility.
For example, to print from WordPad, proceed as follows:
3. Select [Print...] from the [File] menu.
1 Open the document you want to print.
R The [Print] dialogue box will appear.
2 Select [Print...] from the [File] menu.
4. Select [Panasonic Easy Print Driver] as the active
3 Select [Panasonic Easy Print Driver] as the active
printer.
printer.
5. Click [Print].
R The document will be added after the last page of
the previous document in the print preview
window.
4 Click [Print].
R The [Panasonic Easy Print Utility] dialogue will
be displayed. For details about the Easy Print
Utility, click [ ], then click the desired item.
8. Click [Print] icon on the print toolbar.
5 View the print image by clicking the desired page in
the print page window (left column list).
Note:
R The maximum number of documents that can be
displayed in the [Print Page Operation] window is
999 pages.
Saving a file as PDF file
You can save the previewed files in PDF format instead
of printing it.
2. Click the [Save PDF file] icon on the Print toolbar.
R The [Save As] dialogue box appears.
3. Specify the folder to save, enter the file name, and
then click [Save]. The [Save PDF file] dialogue
appears while PDF files are being created and saved.
Note:
R The PDF file created with Easy Print Utility is an
image type.
R To combine multiple documents created in
various applications, see page 30.
R Even if you set the number of prints on the original
application beforehand, you may have to re-set it
for the Easy Print Utility.
30
4. Scanner
4 For USB connection:
4.1 Scanning from the unit (Push
Scan)
Press MCN or MDN repeatedly to select “USB HOST”.
A MSetN
4. . Scanner
For LAN connection (KX-MB2000/KX-MB2010/
KX-MB2030 only):
You can easily scan the document by using the operation
panel on the unit. You can select one of the following
scanning modes depending on how you intend to use the
scanned image.
Press MCN or MDN repeatedly to select the computer to
which you want to send the scanned image. A
MSetN
–
–
–
Viewing using Multi-Function Viewer (Viewer)
Saving as a file to your computer (File)
Sending as an attached file to an email destination
from your computer (Email)
5 If necessary, change the scanning settings. Press
MEN, press MCN or MDN repeatedly to select the desired
setting. A MSetN
–
–
Using OCR software (OCR)
Sending as an attached file to an email destination
directly from this unit (Email address)
6
MStartN
R The scanned image will be displayed in the
[Multi-Function Viewer] window after scanning.
However, when you select PDF as a file format,
the software that is associated to open PDF files
will start.
–
–
Sending to an FTP server (FTP)
Sending to an SMB folder (SMB)
*1 KX-MB2000/KX-MB2010/KX-MB2030 only
Note:
Note:
R You can save the images in TIFF, JPEG, BMP or
R You can set the desired scan mode for push scan
beforehand (feature #493 on page 69).
PDF formats.
R When scanning a document, we recommend using
the scanner glass rather than the automatic
document feeder for better results (KX-MB2010/
KX-MB2025/KX-MB2030 only).
R The scanned image will be automatically saved in the
4.1.2 Scan to save as a file
R Do not open the document cover when scanning a
document with the automatic document feeder
(KX-MB2010/KX-MB2025/KX-MB2030 only).
2
MScanN
Station keys MScanN
3 Press MCN or MDN repeatedly to select “FILE”. A
MSetN
4 For USB connection:
Press MCN or MDN repeatedly to select “USB HOST”.
A MSetN
For LAN connection (KX-MB2000/KX-MB2010/
KX-MB2030 only):
Press MCN or MDN repeatedly to select the computer to
which you want to send the scanned image. A
MSetN
5 If necessary, change the scanning settings. Press
MEN, press MCN or MDN repeatedly to select the desired
setting. A MSetN
MLowerN
MStartN MStopN
MSetNMCNMDNMEN
6
MStartN
R The scanned image will be automatically saved
in the folder selected in the [Settings] window.
* The pictured model is KX-MB2025.
Note:
4.1.1 Scan to Multi-Function Viewer
R You can save the images in TIFF, JPEG, BMP or
PDF formats.
2
MScanN
4.1.3 Scan to Email
3 Press MCN or MDN repeatedly to select “VIEWER”.
A MSetN
You can send the scanned image as an email attachment
using email software on your computer.
31
4. Scanner
Note:
R You can save the images in TIFF, JPEG or BMP
2
MScanN
3 Press MCN or MDN repeatedly to select “EMAIL”. A
formats.
MSetN
R For detailed instructions about OCR, select [Help].
R The scanned image will be automatically saved in the
4 For USB connection:
Press MCN or MDN repeatedly to select “USB HOST”.
A MSetN
4.1.5 Scan to email address (KX-MB2000/
KX-MB2010/KX-MB2030, LAN connection
only)
For LAN connection (KX-MB2000/KX-MB2010/
KX-MB2030 only):
Press MCN or MDN repeatedly to select the computer to
which you want to send the scanned image. A
MSetN
You can send the scanned image as an attachment
without using email software.
5 If necessary, change the scanning settings. Press
MEN, press MCN or MDN repeatedly to select the desired
setting. A MSetN
Important:
R Program the email server, SMTP server settings
6
MStartN
R The email software will automatically start and the
scanned image will be attached to a new email
message.
2
MScanN
3 Press MCN or MDN repeatedly to select “EMAIL
Note:
ADDRESS”. A MSetN
R You can save the images in TIFF, JPEG or PDF
4 Enter the destination email address.
Using station 1–3 (KX-MB2030 only):
Press the desired station key.
formats.
R The scanned image will be automatically saved in the
Using station 4–6 (KX-MB2030 only):
Press MLowerN, then press the desired station key.
Using navigator key:
4.1.4 Scan to OCR
Press MCN or MDN repeatedly to select the desired
destination.
Using dial keypad:
Press MSetN, then enter the email address using the
With OCR software, you can convert an image into text
data that can be edited with word processing software.
Readiris OCR software can be installed when installing
Multi-Function Station.
5
MSetN
6 If necessary, change the scanning settings. Press
MEN, press MCN or MDN repeatedly to select the desired
setting. A MSetN
2
MScanN
3 Press MCN or MDN repeatedly to select “OCR”. A
MSetN
7
MStartN
4 For USB connection:
R The scanned image will be sent as an email
attachment directly from this unit.
Press MCN or MDN repeatedly to select “USB HOST”.
A MSetN
Note:
R You can save the images in TIFF, JPEG or PDF
For LAN connection (KX-MB2000/KX-MB2010/
KX-MB2030 only):
formats.
Press MCN or MDN repeatedly to select the computer to
which you want to send the scanned image. A
MSetN
R You can search for an email address by initial.
Example: “LISA”
5 If necessary, change the scanning settings. Press
MEN, press MCN or MDN repeatedly to select the desired
setting. A MSetN
6
MStartN
2. Press M5N repeatedly to display any name with the
R The scanned image will be displayed in the OCR
window after scanning.
R To search for symbols, press MGN.
3. Press MCN or MDN repeatedly to display “LISA”.
R To stop the search, press MStopN.
32
4. Scanner
R You can easily send scanned image to the desired
destinations using station keys (KX-MB2030 only).
To use this feature, register email addresses to
station keys beforehand (page 70).
2
MScanN
3 Press MCN or MDN repeatedly to select “SMB
FOLDER”. A MSetN
4 Press MCN or MDN repeatedly to select the folder to
which you want to send the scanned image. A
MSetN
2. MScanN
3. Using station 1–3:
Press the desired station key.
5 If necessary, change the scanning settings. Press
MEN, press MCN or MDN repeatedly to select the desired
setting. A MSetN
Using station 4–6:
6
MStartN
Press MLowerN, then press the desired station
key.
R The scanned image will be automatically saved
in the selected folder on the network.
4. MSetN A MStartN
Note:
4.1.6 Scan to FTP server (KX-MB2000/
KX-MB2010/KX-MB2030, LAN connection
only)
R You can save the images in TIFF, JPEG or PDF
formats.
R If this function does not perform properly, consult
your network administrator. This unit’s SMB function
does not support NTMLv2 and SMB signatures.
You can send the scanned image to a folder on an FTP
server.
Important:
R Program the FTP server settings beforehand
2
MScanN
3 Press MCN or MDN repeatedly to select “FTP
SERVER”. A MSetN
4 Press MCN or MDN repeatedly to select the destination
to which you want to send the scanned image. A
MSetN
5 If necessary, change the scanning settings. Press
MEN, press MCN or MDN repeatedly to select the desired
setting. A MSetN
6
MStartN
R The scanned image will be automatically saved
in the selected folder on the FTP server.
Note:
R You can save the images in TIFF, JPEG or PDF
formats.
R To display the scanned image, download the data to
your computer beforehand.
4.1.7 Scan to SMB folder (KX-MB2000/
KX-MB2010/KX-MB2030, LAN connection
only)
You can send the scanned image to a folder on the
network.
Important:
R Program the SMB folder settings beforehand
33
4. Scanner
document again and click [Scan] (KX-MB2010/
KX-MB2025/KX-MB2030 only).
R The scanned image will be displayed in the
4.2 Scanning from a computer
(Pull Scan)
[Multi-Function Viewer] window after scanning.
Note:
R To save the scanned image, select [Save As ...]
R When scanning a document, we recommend using
the scanner glass rather than the automatic
document feeder for better results (KX-MB2010/
KX-MB2025/KX-MB2030 only).
R Do not open the document cover when scanning a
document with the automatic document feeder
(KX-MB2010/KX-MB2025/KX-MB2030 only).
from the [File] menu.
R To cancel scanning while the documents are
being scanned, click [Cancel].
Note:
R You can display images in applications that support
TIFF, JPEG, PCX, DCX and BMP formats.
R You can save images in TIFF, JPEG, PCX, DCX,
BMP or PDF formats.
4.2.1 Using Multi-Function scan application
R If the [Select...] button is displayed in [Target
Device], click [Select...] to select the unit from the
list, and then click [OK].
By clicking an application icon, the selected application
starts automatically after scanning.
The [Select...] button will not be displayed when
there is only one printer driver installed.
2 Start Multi-Function Station. A [Scan]
R You can move, copy and delete a file or page.
3 Click the desired application icon.
R When you click [Custom], the pre-programmed
application starts.
4.2.3 Using other applications
Multi-Function Station includes a TWAIN and WIA
compliant scanner driver. You can also scan using other
applications that support TWAIN or WIA scanning. For
scanning example, proceed as follows:
R To cancel scanning while the documents are
being scanned, click [Cancel].
Note:
R You can change the scanning settings beforehand for
each application (page 27).
R When you point to an application icon, the scanning
2 Start an application that supports TWAIN or WIA
scanning.
settings for that application are displayed as a tooltip.
3 For TWAIN scanning:
R The scanned image will be automatically saved in the
Select [Acquire Image...] from the [File] menu.
For WIA scanning:
Select [From Scanner or Camera...] from the
[File] menu.
4.2.2 Using Multi-Function Viewer
R The unit’s name dialogue box will appear.
4 If necessary, change the scanning settings on your
computer. A [Scan]
2 Start Multi-Function Station.
3 [Utilities] A [Viewer]
R The scanned image will be displayed in the
application window after scanning.
R [Multi-Function Viewer] will appear.
4 Click the [Scan] icon in the [Multi-Function
Viewer] window.
R To cancel scanning while the documents are
being scanned, click [Cancel].
R The unit’s name dialogue box will appear.
Note:
5 If necessary, change the scanning settings on your
computer.
R Scanning from WIA compliant applications is only
available for Windows XP and Windows Vista, and
only via a USB connection.
R To preview the scanned image, click [Preview].
You can drag the frame to specify the scanning
area. If you change the scan settings, click
[Preview] to refresh the scanned image.
If you use the automatic document feeder
(KX-MB2010/KX-MB2025/KX-MB2030 only),
only the first page will be previewed. When you
need to refresh the scanned image, set the
document to preview again.
R Depending on the application used, the appearance
may differ slightly.
R If the [Select...] button is displayed in [Target
Device] when performing TWAIN scanning, click
[Select...] to select the unit from the list, and then
click [OK].
The [Select...] button will not be displayed when
there is only one printer driver installed.
6 [Scan]
R If you preview the scanned image using the
automatic document feeder in step 5, set the
34
5. Copier
2. Press MCN or MDN repeatedly to select the size of your
original document. A MSetN
5.1 Making a copy
3. Press MCN or MDN repeatedly to select the size of
recording paper size.
5. . Copier
5.1.1 Using the scanner glass
R When “#2” is selected, you can change the
recording paper size by pressing MEN repeatedly.
R The appropriate zoom rate will be set
automatically. Some copying features cannot be
used during zoom copy. See page 36 for
details.
4. MSetN
To select the resolution
1. Press MResolutionN repeatedly.
–
–
–
“TEXT/PHOTO”: For both text and photographs.
“TEXT”: For text only.
“PHOTO”: For photographs, shaded drawings,
etc.
2. MSetN
MCopyN
Note:
R You can change the default resolution (feature #461
MCopy SizeN
MStartN MStopN
MContrastN
To select the contrast
MResolutionN MSetNMCNMDNMEN
Adjust this setting depending on the darkness or
lightness of the document. 5 levels (low to high) are
available.
MFax Auto AnswerN
* The pictured model is KX-MB2025.
Press MContrastN repeatedly. A MSetN
1 If the MCopyN light is OFF, turn it ON by pressing
Note:
MCopyN.
R You can hold the previous contrast setting (feature
3 If necessary, change the copy size (original
document size and recording paper size), resolution
and contrast according to the type of document.
4 If necessary, enter the number of copies (up to 99).
5
MStartN
R The unit will start copying.
6 After you finish copying, press MStopN to reset the
Note:
R You can change the default operation mode (feature
the default operation mode (feature #464 on
R If the MFax Auto AnswerN light is ON, the unit can
receive faxes automatically even when in the copy
mode (KX-MB2025/KX-MB2030 only).
To select the copy size
1. Press MCopy SizeN repeatedly to select “ORIGINAL
SIZE”.
35
5. Copier
5.1.2 Using the automatic document feeder
(KX-MB2010/KX-MB2025/KX-MB2030 only)
5.2 More copying features
R Make sure that the MCopyN light is ON.
MCopyN
5.2.1 Zoom copy (enlargement / reduction)
2 Press MZoomN repeatedly to select the zoom rate that
fits the size of your document and recording paper.
–
“ZOOM =100%”
“50%”
–
–
“200%”
*1
Press MCN or MDN repeatedly to change the zoom
rate by 1 % at a time from “25%” to “400%”.
You can also enter the desired percentage
specifically by using the dial keys.
3
MSetN
MStartN MStopN
4 If necessary, enter the number of copies (up to 99).
A MStartN
* The pictured model is KX-MB2010.
5 After you finish copying, press MStopN to reset this
1 If the MCopyN light is OFF, turn it ON by pressing
feature.
MCopyN.
Note:
R Zoom copy is not available for the following features:
3 If necessary, change the copy size (original
document size and recording paper size), resolution
and contrast according to the type of document.
–
–
–
–
–
R You can hold the previous zoom setting (feature #468
4 If necessary, enter the number of copies (up to 99).
R When using the scanner glass, the unit will only
5
MStartN
enlarge the right top corner of the document starting
R The unit will start copying.
from the
mark on the unit.
6 After you finish copying, press MStopN to reset the
R When using the automatic document feeder, the
unit will only enlarge the centre of the upper part of
the document. To make an enlarged copy of the
bottom of the document, turn the document around,
and then make a copy (KX-MB2010/KX-MB2025/
KX-MB2030 only).
Note:
36
5. Copier
Example: 150 % enlarged copy
2. Place the next document on the scanner glass
and press MSetN. Repeat this until you have
scanned all pages, and then press MStartN.
R The unit will start copying.
Using the scanner glass (A):
Original document
Enlarged copy
When using the automatic document feeder
(KX-MB2010/KX-MB2025/KX-MB2030 only):
MStartN
8 After you finish copying, press MStopN to reset this
feature.
A
Example: Making 2 copies of a 4-page original
document
Using the automatic document feeder (KX-MB2010/
KX-MB2025/KX-MB2030 only):
4
Original document
Enlarged copy
3
4
2
4
1
3
3
4
2
3
2
Example: 70 % reduced copy
1
2
1
1
Using the scanner glass (A):
Original document
Reduced copy
Collated pages
Uncollated pages
Note:
R The unit will store the documents into memory while
collating the copies. If the memory becomes full while
storing, the unit will only print out the stored pages.
A
R You can hold the previous collate setting (feature
Using the automatic document feeder (KX-MB2010/
KX-MB2025/KX-MB2030 only):
Proof set feature (KX-MB2010/KX-MB2025/
KX-MB2030 only)
Original document
Reduced copy
To make 1 set of a collated copy first, press MCN or MDN
set of a collated copy and stop temporarily so you can
check whether the copy was made as you expected. If
the copy is correct, press MStartN to continue copying.
If the copy is not correct, press MStopN and start again
from the beginning.
5.2.2 Collate copy
The unit can collate multiple copies in the same order as
the original document pages.
5.2.3 Quick ID copy feature / Image repeat
feature (Scanner glass only)
1 If the MCopyN light is OFF, turn it ON by pressing
MCopyN.
Quick ID copy feature: To copy 2-sided documents
onto one page.
Image repeat feature: To copy a single document
repeatedly onto one page.
3 Press MFN to display “COLLATE”.
4 Press MCN or MDN repeatedly to display “ON”.
Note:
5
MSetN
R The copied documents will not be reduced to fit the
recording paper, and useful for copying small sized
documents such as business cards.
6 Enter the number of copies (up to 99).
7 When using the scanner glass:
1. MStartN
R The unit will scan 1 page.
37
5. Copier
Original document
Page layout
R To make a landscape copy, set the original in
landscape direction. To make a portrait copy, set
the original in portrait direction.
“4 in 1”
“LANDSCAPE”
R The scanning area changes according to the
for details. The shaded area will be scanned.
2 Press MPage LayoutN repeatedly to select “PAGE
“PORTRAIT”
LAYOUT”.
3 Press MCN or MDN repeatedly to select “QUIK ID
COPY” or “IMAGE REPEAT”. A MSetN
4 Press MCN or MDN repeatedly to select the number of
original documents from “2 in 1”, “4 in 1” or “8
in 1”. A MSetN
“8 in 1”
“LANDSCAPE”
R For quick ID copy feature, go to the next step.
5 Press MCN or MDN repeatedly to select the page layout
from “LANDSCAPE” or “PORTRAIT”. A MSetN
6 If necessary, enter the number of copies (up to 99).
“PORTRAIT”
7 Quick ID copy feature:
1. MStartN
R The unit will scan 1 page.
2. Place the next document on the scanner glass
and press MSetN. Repeat this until all the
documents are scanned.
R The unit will start copying.
For image repeat feature
R You can press MStartN anytime to start
Original document
Page layout
copying.
Image repeat feature:
“2 in 1”
MStartN
8 After you finish copying, press MStopN to reset this
feature.
Note:
R You can save the previous page layout setting
For quick ID copy feature
“4 in 1”
Original document
Page layout
“2 in 1”
“LANDSCAPE”
“PORTRAIT”
38
5. Copier
Original document
Page layout
R To make a portrait copy, set the original in portrait
direction. To make a landscape copy, set the
original in landscape direction.
“8 in 1”
2 Press MPage LayoutN repeatedly to select “PAGE
LAYOUT”.
3 Press MCN or MDN repeatedly to select “N in 1”.
A MSetN
4 Press MCN or MDN repeatedly to select the number of
original documents from “2 in 1”, “4 in 1” or “8
in 1”. A MSetN
5 Press MCN or MDN repeatedly to select the layout from
“PORTRAIT” or “LANDSCAPE”. A MSetN
5.2.4 Poster feature (Scanner glass only)
6 If necessary, enter the number of copies (up to 99).
You can make copies divided into 2 (“1 X 2”), 4 (“2 X
2”) or 9 (“3 X 3”) sections to make enlarged copies of
the individual sections. You can then glue them together
to make a poster.
7 When using the scanner glass:
1. MStartN
R The unit will scan 1 page.
2. Place the next document on the scanner glass
and press MSetN. Repeat this until all the
documents are scanned.
R The unit will start copying.
R You can press MStartN anytime to start
copying.
When using the automatic document feeder
(KX-MB2010/KX-MB2025/KX-MB2030 only):
MStartN
8 After you finish copying, press MStopN to reset this
feature.
Original document
Page layout
“2 in 1”
“PORTRAIT”
2 Press MPage LayoutN repeatedly to select “PAGE
LAYOUT”.
“LANDSCAPE”
3 Press MCN or MDN repeatedly to select “POSTER”.
A MSetN
4 Press MCN or MDN repeatedly to select “1 X 2”, “2 X
2” or “3 X 3”. A MSetN
“4 in 1”
“PORTRAIT”
5 If necessary, enter the number of copies (up to 99).
A MStartN
6 After you finish copying, press MStopN to reset this
feature.
Note:
“LANDSCAPE”
R You can save the previous page layout setting
5.2.5 N in 1 feature
You can save paper by copying 2, 4 or 8 pages onto 1
page. The documents will be reduced to fit the recording
paper.
39
5. Copier
5 Enter the desired edge width of long edge using the
Original document
Page layout
dial keypad. A MSetN
“8 in 1”
“PORTRAIT”
6 Press MCN or MDN repeatedly to select “SHORT
EDGE”. A MSetN
7 Enter the desired edge width of short edge using the
dial keypad. A MSetN
8
MStartN
“LANDSCAPE”
9 After you finish copying, press MStopN to reset this
feature.
Note:
R You can hold the previous edge setting (feature #473
Note:
5.2.7 Margin feature
R You can save the previous page layout setting
You can set the unit not to copy a particular edge of the
document to make a margin. This is useful for binding
the copied documents.
Separate N in 1 feature (Scanner glass only)
Note:
You can separate an N in 1 copied document back into
its original, separate pages. This feature is available for
documents created using the “2 in 1” and “4 in 1”
settings.
R To automatically reduce the copies according to the
R This feature and page layout features cannot be used
at the same time.
2. Press MPage LayoutN repeatedly to select “PAGE
LAYOUT”.
R To make a portrait copy, set the original in portrait
direction. To make a landscape copy, set the
original in landscape direction.
3. Press MCN or MDN repeatedly to select “SEPARATE N
in 1”. A MSetN
2 Press MPage LayoutN repeatedly to select
4. Press MCN or MDN repeatedly to select the number of
original documents from “2 in 1” or “4 in 1”.
A MSetN
“MARGIN”.
3 Press MCN or MDN repeatedly to select “ON”. A
5. Press MCN or MDN repeatedly to select the page layout
of the original document from “PORTRAIT” or
“LANDSCAPE”. A MSetN
MSetN
4 Press MCN or MDN repeatedly to select the page layout
from “PORTRAIT” or “LANDSCAPE”. A MSetN
6. If necessary, enter the number of documents (up to
5 Press MCN or MDN repeatedly to select the edge you
want to set the margin for from “TOP”, “RIGHT”,
“LEFT” or “BOTTOM”. A MSetN
99). A MStartN
7. After you finish copying, press MStopN to reset this
feature.
6 Enter the desired margin width using the dial keypad.
A MSetN
5.2.6 Edge feature
7
MStartN
You can set the unit not to copy the outer edges of the
document without reducing the copied documents to fit
the recording paper. This is useful for copying
documents with dirty edges.
8 After you finish copying, press MStopN to reset this
feature.
Note:
Note:
R You can hold the previous margin setting (feature
R This feature and page layout features cannot be used
at the same time (except for N in 1).
5.2.8 Copy reservation
You can make a copy reservation under the following
conditions:
2 Press MPage LayoutN repeatedly to select “EDGE”.
3 Press MCN or MDN repeatedly to select “ON”. A
–
while the unit is printing documents from your
computer.
MSetN
4 Press MCN or MDN repeatedly to select “LONG EDGE”.
–
while the unit is printing received fax documents
(KX-MB2025/KX-MB2030 only).
A MSetN
40
5. Copier
2 While “PC PRINTING” or “PRINTING”
(KX-MB2025/KX-MB2030 only) is displayed, press
MCopyN.
3 Make necessary settings such as number of copies,
resolution, zoom features and page layout features.
A MStartN
R “COPY RESERVED” will be displayed. The unit
will start copying after the current printing job.
41
6. Fax (KX-MB2025/KX-MB2030 only)
To select the resolution
6.1 Sending a fax manually
1. Press MResolutionN repeatedly.
–
–
–
–
“STANDARD”: For normal-sized characters.
6. . Fax (KX-MB2025/KX-MB2030 only)
6.1.1 Using the scanner glass
“FINE”: For small-sized characters.
“SUPER FINE”: For very small-sized characters.
By using the scanner glass, you can send a page from
booklets or small size paper.
“PHOTO”: For photographs, shaded drawings,
etc.
2. MSetN
R Using the “FINE”, “SUPER FINE” and “PHOTO”
settings will increase transmission time.
To select the contrast
Adjust this setting depending on the darkness or
lightness of the document. 5 levels (low to high) are
available.
Press MContrastN repeatedly. A MSetN
Note:
R You can save the previous contrast setting (feature
To redial the last number
MRedialN
R If the line is busy, the unit will automatically redial the
MFaxN
number 2 or more times.
MSetN MStartN
MRedialN
Note:
MContrastN
MQuick ScanN
MResolutionN
Reserving the fax transmission (Dual Access)
1 If the MFaxN light is OFF, turn it ON by pressing
You can reserve a fax transmission even when the unit
is just receiving a fax or sending a fax from memory.
MFaxN.
–
–
Up to 3 reservations when sending
Up to 4 reservations when receiving
3 If necessary, change the resolution and contrast
according to the type of document.
1. Set the original during fax reception or fax memory
transmission.
2. Enter the fax number using the dial keypad,
one-touch dial or phonebook.
4 Dial the fax number.
3. When using the scanner glass, press MQuick
ScanN. The unit will scan 1 page. Place the next
document on the scanner glass and press MSetN.
Repeat this until all the documents are scanned, then
press MStartN.
R To send multiple pages, go to the next step.
5 Press MQuick ScanN to scan the document into
memory.
When using the automatic document feeder,
press MStartN.
R Wait until “SCAN:PRESS SET” “SEND:PRESS
START” is displayed.
R If the document exceeds the memory capacity, the
reservation for that document will be cancelled. You
must send the entire document manually.
6 Place the next page on the scanner glass. A MSetN
R To send more pages, repeat this step.
7
MStartN
Printing a sending report
Note:
A sending report provides you with a printed record of
transmission results. To print the sending reports, make
explanation of the messages, see page 80.
R You can change the default operation mode (feature
the default operation mode (feature #464 on
Printing a journal report
A journal report provides you with a printed record of the
30 most recent faxes. To print it manually, see
42
6. Fax (KX-MB2025/KX-MB2030 only)
fax transmissions and receptions, make sure feature
6.2 Storing items for the
one-touch dial feature and
phonebook
6.1.2 Using the automatic document feeder
The unit provides the one-touch dial feature (6 items) and
phonebook (100 items).
R Station 1 and 2 can be used alternatively as
MFaxN
R Make sure that the MFaxN light is ON.
Station keys MPhonebookN MMenuN MStopN
MLowerN MFaxN
MSetN MCNMDNMEN
MMonitorN
MStartN
6.2.1 Storing one-touch dial item
MQuick ScanN
1 Press MMenuN repeatedly to display “PHONEBOOK
1 If the MFaxN light is OFF, turn it ON by pressing
SET”.
MFaxN.
2 Select the desired station key.
For station 1–2:
3 If necessary, change the resolution and contrast
according to the type of document.
1. Press one of the station keys.
2. Press MCN or MDN repeatedly to select “DIAL
MODE”. A MSetN
For station 3:
4
MMonitorN
Press the station key.
5 Dial the fax number.
For station 4–6:
6 When a fax tone is heard:
Press MLowerN, then press one of the station keys.
Press MStartN.
When the other party answers your call:
for character entry). A MSetN
Lift the handset and ask them to press their start
button. When the fax tone is heard, press MStartN.
4 Enter the telephone number, up to 32 digits. A
MSetN
Note:
R After pressing MStartN, you can replace the handset.
R Do not open the document cover when sending a fax
5
MStopN
Note:
R A hyphen or a space entered in a telephone number
with the automatic document feeder.
counts as 2 digits.
Pre-dialling a fax number
6.2.2 Storing phonebook items
1. Enter the fax number.
1 Press MMenuN repeatedly to display “PHONEBOOK
SET”. A MEN
Sending from memory (Quick scan feature)
for character entry). A MSetN
2. Enter the fax number. A MQuick ScanN
3 Enter the telephone number, up to 32 digits. A
MSetN
43
6. Fax (KX-MB2025/KX-MB2030 only)
4
MMenuN
6.3 Sending a fax using one-touch
dial feature and phonebook
Before using this feature, store the desired names and
telephone numbers into the one-touch dial feature and
phonebook (page 43).
Note:
R A hyphen or a space entered in a telephone number
counts as 2 digits.
6.2.3 Editing a stored item
R Make sure that the MFaxN light is ON.
1
MPhonebookN
6.3.1 Using the scanner glass
2 Press MCN or MDN repeatedly to display the desired
item. A MMenuN A MGN
3 Edit the name if necessary. A MSetN
4 Edit the telephone number if necessary. A MSetN
A MStopN
3 Enter the fax number.
Using station 1–3:
6.2.4 Erasing a stored item
Press the desired station key.
1
MPhonebookN
Using station 4–6:
2 Press MCN or MDN repeatedly to display the desired
item. A MMenuN A MBN
Press MLowerN, then press the desired station key.
Using phonebook:
R To cancel erasing, press MStopN.
Press MPhonebookN, then press MCN or MDN
repeatedly to display the desired item.
3
MSetN A MStopN
R To send multiple pages, go to the next step.
4 Press MQuick ScanN to scan the document into
memory.
5 Place the next page. A MSetN
R To send more pages, repeat this step.
6
MStartN
To search for a name by initial
Example: “LISA”
1. MPhonebookN
2. Press MCN or MDN to initiate the phonebook.
3. Press M5N repeatedly to display any name with the
R To search for symbols, press MGN.
4. Press MCN or MDN repeatedly to display “LISA”.
R To stop the search, press MStopN.
Fax auto redial
If the line is busy or if there is no answer, the unit will
automatically redial the number 2 or more times.
Note:
6.3.2 Using the automatic document feeder
3 Enter the fax number using one-touch dial or
phonebook.
44
6. Fax (KX-MB2025/KX-MB2030 only)
4
MStartN
6.4 Broadcast transmission
You can send the same document to multiple parties (up
to 20). To use this feature, store the fax numbers into
broadcast memory as follows.
Broadcast: Store items using one-touch dial or
phonebook (page 43).
Manual broadcast: Store items using one-touch dial or
to store items manually.
Your programmed items will remain in the broadcast
memory, allowing frequent re-use.
R The broadcast function utilises station 1–2. The
one-touch dial function will be cancelled.
R Make sure that the MFaxN light is ON.
6.4.1 Programming items into the broadcast
memory
1 Press MMenuN repeatedly to display “PHONEBOOK
SET”.
2 Select the desired broadcast key.
For BROADCAST:
1. MBroadcastN
2. Press MCN or MDN repeatedly to select
“BROADCAST”.
For MANUAL BROADCAST:
1. MManual BroadN
2. Press MCN or MDN repeatedly to select “MANUAL
BROAD”.
3
MSetN
4 Program items.
Using station 1–3:
Press the desired station key.
Using station 4–6:
Press MLowerN, then press the desired station key.
Using phonebook:
Press MCN or MDN repeatedly to display the desired
item. A MSetN
Using the dial keypad (only for manual broad):
Enter the fax number. A MSetN
R The number in brackets indicates the number of
registered items.
R To program other items, repeat this step (up to 20
items).
R If you have programmed the wrong item, press
MStopN to erase the item.
5
6
MSetN
R To program another broadcast key, repeat steps
MStopN
45
6. Fax (KX-MB2025/KX-MB2030 only)
To send the same document using the automatic
document feeder
6.4.2 Adding a new item into the broadcast
memory
1
MPhonebookN
2 Press MCN or MDN repeatedly to display the desired
broadcast memory location (“<BROADCAST>” or
“<MANUAL BROAD>”). A MMenuN A MGN
3. Press MBroadcastN or MManual BroadN.
3 Press MCN or MDN repeatedly to display the item you
want to add. A MSetN
R To add other items, repeat this step (up to 20
items).
4
MStopN
Note:
R When adding new items to the MANUAL
BROADCAST memory, you can only select stored
items.
6.4.3 Erasing a stored item from the
broadcast memory
1
MPhonebookN
2 Press MCN or MDN repeatedly to display the desired
broadcast memory location (“<BROADCAST>” or
“<MANUAL BROAD>”). A MMenuN A MBN
3 Press MCN or MDN repeatedly to display the item you
want to erase.
R To cancel erasing, press MStopN.
4
MSetN A MSetN A MStopN
6.4.4 Sending the same document to
pre-programmed parties
To send the same document using the scanner glass
3. Press MBroadcastN or MManual BroadN.
R To send multiple pages, go to the next step.
4. Place the next page. A MSetN
R To send more pages, repeat this step.
5. MStartN
Note:
R If you select “FINE”, “SUPER FINE” or “PHOTO”
resolution, the number of pages that the unit can
send will decrease.
R If the document exceeds the memory capacity,
sending will be cancelled.
R If a party is busy or does not answer, it will be skipped
and redialled later 2 or more times.
R After transmission, the unit will automatically print a
report (broadcast sending report).
46
6. Fax (KX-MB2025/KX-MB2030 only)
6.5 Sending an electronic
6.6 Selecting the way to use your
document as a fax message from unit
Depending on your situation, select the way you prefer
to use your unit.
your computer
You can access the fax function from a Windows
application using Multi-Function Station.
For example, to send a document created from
WordPad, proceed as follows.
–
–
–
–
Use only as a fax (FAX ONLY mode)
Use mostly as a telephone (TEL mode)
Use as a telephone and/or fax (TEL/FAX mode)
Use with answering machine
1 Open the document you want to send.
2 Select [Print...] from the [File] menu.
6.6.1 Use only as a fax (FAX ONLY mode)
R The [Print] dialogue box will appear.
Your situation
3 Select the PCFAX unit’s name as the active printer.
You have a separate telephone line just for faxes, or you
want to use the unit only for receiving faxes.
4 Click [Print].
R The [Send a Fax] dialogue box will appear.
Setup
MFax Auto AnswerN repeatedly.
R The MFax Auto AnswerN light turns ON.
5 Enter the fax number using the keypad display or the
directory.
Fax Auto
Answer
R To stop the operation, click [Cancel].
6 [Send]
R The document will be sent through the unit from
your computer.
How faxes are received
Note:
All incoming calls will be answered as faxes.
6.6.2 Use mostly as a telephone (TEL mode)
R If the document exceeds the memory capacity of the
unit, sending will be cancelled.
R For details, see the help file by selecting [ ] from
Multi-Function Station.
R Click [Select...] to change the active unit.
Your situation
You want to answer calls by yourself. If a fax call is
received, you must receive the fax manually.
Setup
Auto AnswerN repeatedly.
R The MFax Auto AnswerN light turns OFF.
Fax Auto
Answer
47
6. Fax (KX-MB2025/KX-MB2030 only)
Note:
6.7 Receiving a fax automatically
– Auto answer ON
R Make sure feature #404 is set to “TEL” beforehand
How to receive phone calls and faxes
R A4 or letter size recording paper can be used.
You have to answer all calls manually.
To receive a fax document, press MStartN and then M2N.
6.7.1 Activating FAX ONLY mode
Press MFax Auto AnswerN repeatedly to display “FAX
ONLY MODE”.
R The MFax Auto AnswerN light turns ON.
6.6.3 Use as a telephone and/or fax (TEL/FAX
mode)
Your situation
You want to answer phone calls yourself and receive
faxes automatically without rings.
Setup
MFax Auto AnswerN repeatedly.
R The MFax Auto AnswerN light turns OFF.
Fax Auto
Answer
Note:
Fax Auto
Answer
R Make sure feature #404 is set to “TEL/FAX”
How phone calls and faxes are received
If the call is a phone call, the unit will ring.
If a fax calling tone is detected, the unit will receive the
fax automatically without ringing.
How faxes are received
When receiving calls, the unit will automatically answer
all calls and only receive fax documents.
6.6.4 Use with answering machine
Note:
Your situation
R The number of rings before a call is answered in FAX
ONLY mode can be changed (feature #210 on
You want to use the unit with an answering machine.
Setup
Connect an external telephone answering machine and
set the ring count of the answering machine to less than
4.
R Set the ring count in FAX ONLY mode of the unit to
more than 4, if you use with auto answer ON.
How to receive calls
When receiving phone calls, the answering machine will
record voice messages.
48
6. Fax (KX-MB2025/KX-MB2030 only)
–
no sound is heard,
6.8 Receiving a fax manually –
Auto answer OFF
press MGN MBN M9N (default fax activation code)
firmly.
3. Replace the handset.
R A4 or letter size recording paper can be used.
Note:
6.8.1 Activating TEL mode
R To receive fax documents using the extension
telephone, make sure remote fax activation is turned
ON (feature #434 on page 64) beforehand. The
default setting is ON.
1 Make sure feature #404 is set to “TEL” beforehand
2 Press MFax Auto AnswerN repeatedly to display
“TEL MODE”.
6.8.2 Activating TEL/FAX mode
R The MFax Auto AnswerN light turns OFF.
1 Make sure feature #404 is set to “TEL/FAX”
2 Press MFax Auto AnswerN repeatedly to display
“TEL/FAX MODE”.
R The MFax Auto AnswerN light turns OFF.
Fax Auto
Answer
MStartN
Note:
R If you do not answer the call within 10 rings, the unit
will temporarily switch to fax reception. The other
party can then send a fax.
Fax Auto
Answer
MStopN
How to receive phone calls and faxes with the
handset unit
1. Lift the handset to answer the call.
How phone calls and faxes are received
2. When:
1. “INCOMING CALL” will be displayed but the unit will
–
–
–
document reception is required,
a fax calling tone (slow beep) is heard, or
no sound is heard,
not ring.
2. The unit will wait for the duration of 2 rings before
answering the call.
press MStartN, and then M2N.
R The number of rings is determined by the “TEL/
FAX delayed ring count” (feature #212 on
3. Replace the handset.
Note:
R During this time, an extension telephone will ring.
3. The unit will answer the call and try to detect a fax
calling tone.
How to receive faxes with an extension telephone
When a fax calling tone is detected
If you have another telephone connected to the [EXT]
jack or the same line (extension telephone), you can use
the extension telephone to receive faxes.
The unit receives the fax automatically without
ringing.
1. When the extension telephone rings, lift the handset
When a fax calling tone is not detected
of the extension telephone.
A The unit will ring 3 times. You may answer the call.
2. When:
–
–
document reception is required,
a fax calling tone (slow beep) is heard, or
49
6. Fax (KX-MB2025/KX-MB2030 only)
R To answer using the handset of the unit (if
connected), lift the handset and talk to the other
party.
B If you do not answer the call, the unit will activate
the fax function.
R Some fax machines do not generate fax calling
tones when sending faxes, therefore the unit will
try to receive a fax even if no fax calling tone is
detected.
–
unit includes a handset, or if an optional handset
is available.
R To answer using another telephone connected to
the [EXT] jack of this unit, lift the handset, then
press MStopN on the unit to talk to the other party.
* The pictured model is KX-MB2030.
R To answer using another telephone connected to
the same telephone line as this unit, lift the
handset and talk to the other party.
* The pictured model is KX-MB2030.
R The number of rings is determined by the “Silent
fax recognition ring count” (feature #436 on
R Callers will hear a ring back tone different from
the one generated by the telephone company.
50
6. Fax (KX-MB2025/KX-MB2030 only)
Note:
6.9 Using the unit with an
answering machine
R If the call is a phone call, the answering machine will
record voice messages.
If a fax calling tone is detected, the fax machine will
receive a fax automatically.
6.9.1 Setting up the unit and an answering
machine
R Regarding the remote access code for the answering
machine, see the operating instructions of the
answering machine.
1 Connect the answering machine (A).
R Answering machine is not supplied.
R Remove the stopper (B) if attached.
Receiving a voice message and fax document in one
call
The caller can leave a voice message and send a fax
document during the same call. Inform the caller of the
following procedure beforehand.
B
1. The caller calls your unit.
R The answering device will answer the call.
2. The caller can leave a message after the greeting
message.
3. The caller presses MGN MBN M9N (pre-selected fax
activation code).
R The unit will activate the fax function.
4. The caller presses the start button to send a
document.
Note:
R To use this feature, make sure remote fax activation
activation code can also be changed.
R If there is no room left in the memory of your
answering machine, the unit may not be able to
receive documents. See the operating instructions of
the answering machine and erase unnecessary
messages.
A
6.10 Receive polling (retrieving a
fax placed on another fax
machine)
This feature allows you to retrieve a document from
another compatible machine. Therefore you pay for the
call.
* The pictured model is KX-MB2030.
2 Set the number of rings on the answering machine to
4 rings or less.
R This will allow the answering machine to answer
the call first.
Make sure that no documents are fed into your unit and
that the other party’s machine is ready for your call.
3 Record a greeting message on the answering
machine.
1 Press MMenuN repeatedly to display “POLLING”.
R We recommend you record a message up to 10
seconds long, and not to pause for more than 4
seconds during the message. Otherwise, neither
machines will function correctly.
A MSetN
2 Dial the fax number. A MStartN
4 Activate the answering machine.
R If you set to FAX ONLY mode, change the ring
count in FAX ONLY mode to more than 4
6 Make sure each of the following is unique:
–
the remote access code of the answering
machine
–
the fax activation code (feature #434 on
51
6. Fax (KX-MB2025/KX-MB2030 only)
2. Press MEN repeatedly to display “JUNK LIST
DISP.”. A MSetN
6.11 Junk fax prohibitor
(preventing fax reception from
undesired callers)
feature prevents fax reception from calls that do not show
caller information.
3. Press MCN or MDN repeatedly to display the desired
item. A MFN
R To cancel erasing, press MStopN, then press
MMenuN.
4. MSetN A MMenuN
Additionally, the unit will not accept faxes originating from
numbers that match the ones on a programmable junk
fax prohibitor list.
Important:
R This feature does not work if you receive faxes
manually.
6.11.1 Activating the junk fax prohibitor
1 Press MMenuN repeatedly to display “JUNK FAX
PROH.”. A MEN
2 Press MCN or MDN repeatedly to select “ON”. A
MSetN
3 Press MStopN to exit.
6.11.2 Storing undesired callers
You can register up to 20 undesired numbers from the
Caller ID list (page 55) if you do not wish to receive
faxes from them.
1 Press MMenuN repeatedly to display “JUNK FAX
PROH.”.
2 Press MEN repeatedly to display “JUNK LIST
SET”. A MSetN
3 Press MCN or MDN repeatedly to display the party you
do not want to receive faxes from. A MSetN
4 Press MStopN 2 times to exit.
To display the junk fax prohibitor list
1. Press MMenuN repeatedly to display “JUNK FAX
PROH.”.
2. Press MEN repeatedly to display “JUNK LIST
DISP.”. A MSetN
3. Press MCN or MDN to display the items on the list.
4. Press MStopN to exit.
To print the junk fax prohibitor list
1. Press MMenuN repeatedly to display “JUNK FAX
PROH.”.
2. Press MEN repeatedly to display “JUNK LIST
PRINT”. A MSetN
3. Press MStopN to exit.
To erase an item from the junk fax prohibitor list
1. Press MMenuN repeatedly to display “JUNK FAX
PROH.”.
52
6. Fax (KX-MB2025/KX-MB2030 only)
6.12 Receiving a fax on your
computer
You can receive a fax document on your computer. The
received fax document is saved as an image file
(TIFF-G4 format).
6.13 Web fax preview
(KX-MB2030, LAN connection
only)
You can display a received fax document in your web
browser, and print or save the necessary document after
you confirm the image.
Important:
R Make sure the PC fax setting is set to “ALWAYS”
or “CONNECTED” beforehand (feature #442 on
R Make sure the computer setting for the PC fax
reception is set beforehand (feature #443 on
Important:
R Web fax preview will not be activated when using
the unit for the first time. To activate this feature,
set the following:
–
R Make sure the fax preview mode is turned OFF
(KX-MB2030, LAN connection only).
–
1 Press MFax Auto AnswerN repeatedly to turn the
6.13.1 Activating the fax preview mode
1
MMenuN A MBNM4NM4NM8N
2 Start Multi-Function Station. A [PC FAX]
2 Press M1N to select “ON”.
3 When a fax call is received, your computer will
R Press M0N to select “OFF”.
receive a document through the unit.
3
MSetN A MMenuN
Note:
R You can view, print or transfer the received document
Note:
using your computer.
R If you select “ON”, the PC fax setting (feature #442
Viewing a received document
1. Select [PC FAX] from Multi-Function Station.
2. Select [Received Log] in [Communication Log].
6.13.2 Programming the web fax preview
access code
1
MMenuN A MBNM4NM5NM0N A MSetN
A MSetN
3 Enter the web fax preview access code, up to 8
characters, using the English alphabet and numbers
R The following symbols can also be entered.
! @ # $ % ^ & ’ ) ( . – _ { }
3. Click the item you want to view.
4
MSetN A MMenuN
4. Click [File] in the menu bar, then select [View], or
click the [View] icon in the toolbar.
Note:
R The received fax will be displayed.
R If the web fax preview access code is not
programmed (blank), the web fax preview feature will
not be activated.
If a received fax document is stored in the unit’s
memory
You can load the document into your computer.
1. Select [PC FAX] from Multi-Function Station.
2. Select [Received Log] in [Communication Log].
6.13.3 Displaying a received fax document on
the web browser
Important:
3. Click [File] in the menu bar. A [Receive a Fax]
is activated, the received fax document will be
automatically transferred to the computer.
R Make sure that the unit is idle.
1 Start Multi-Function Station.
2 [Utilities] A [Configuration Web Page] A
[Device Configuration]
3 Type “root” as the user name, then enter the
53
6. Fax (KX-MB2025/KX-MB2030 only)
4 Select the [WEB FAX PREVIEW] tab.
5 Enter the web fax preview access code (feature #450
R A list of the received fax documents will be
displayed.
6 Click the desired icon to preview, print or save a fax
document.
R While previewing the document, you can
manipulate the fax document (Example: enlarge,
rotate etc.).
7 Close the web browser.
Note:
R The display speed depends on the contents and size
of the document.
R The received fax document is saved as an image file
(PDF format). Adobe Reader is required to view it.
What “ ” means
“
” on the display means the image has already been
viewed, printed or saved.
R To delete a document after viewing a fax document
delete images showing “ ”.
R To delete a document after printing or saving a fax
You can delete images showing “ ”.
54
7. Caller ID (KX-MB2025/KX-MB2030 only)
7.1 Caller ID service
7.2 Viewing and calling back
using caller information
Important:
R If the area code of the received telephone number
is the same as yours, the area code may need to
be deleted before calling back. This may only
apply to some areas. To edit the number, see
This unit is compatible with the Caller ID service
offered by your local telephone company. To use this
unit’s Caller ID features, you must subscribe to a
Caller ID service.
7. . Caller ID (KX-MB2025/KX-MB2030 only)
Important:
R This unit is designed in accordance with the ETS
(European Telecommunication Standard) and
only supports the basic CLIP (Calling Line
Identification Presentation) features.
1 If the MFaxN light is OFF, turn it ON by pressing
MFaxN. A MCaller IDN
R This unit will only display the caller’s telephone
2 Press MCN to search from the recently received caller
number and name.
R This unit will not support future additional
information.
R If you press MDN, the display order will be
reversed.
telephone services.
R Depending on the service of the local telephone
company, the date/time of the call or the caller’s
name may not be displayed.
3 Press MMonitorN or lift the handset to return the call.
Make sure the following ring count is set to 2 or more
rings beforehand.
To change the way caller information is displayed
–
–
R The name display service may not be available in
some areas. For further information, please contact
your telephone company.
While displaying the desired caller information, press
MCaller IDN repeatedly to change name/telephone
number information.
7.2.1 Symbols and operations for caller
information
7.1.1 How Caller ID is displayed
What “ ” means
The calling party’s name or telephone number will be
displayed after the 1st ring. You have the option of
whether or not to answer the call.
“
” on the display means the call has already been
viewed or answered.
The unit will automatically store caller information (name,
telephone number and date and time of the call) from the
30 most recent calls. It is possible to view caller
information on the display (page 55) or print the entire
R When caller information is received and it matches a
telephone number stored in the unit’s one-touch dial
or phonebook, the stored name will be displayed.
R If the unit is connected to a PBX (Private Branch
Exchange) system, caller information may not be
received properly. Consult your PBX supplier.
R If the unit cannot receive caller information, the
following will be displayed:
To stop viewing
Press MStopN.
7.3 Editing a caller’s telephone
number before calling back/
storing
R Make sure that the MFaxN light is ON.
1
MCaller IDN
2 Press MCN or MDN to display the desired item.
“OUT OF AREA”: The caller dialled from an area
which does not provide Caller ID service.
“PRIVATE CALLER”: The caller requested not to
send caller information.
“LONG DISTANCE”: The caller made a long distance
call.
3 Press MCaller IDN to display the telephone number.
4 Press dial key (0 to 9) or MGN to enter the editing
mode and edit the telephone number.
5 Press MMonitorN or lift the handset to call back the
edited number.
To confirm caller information by printing the Caller
ID list
R The unit will start dialling automatically.
Note:
–
–
To print automatically after every 30 new calls,
R The edited telephone number will not be saved in the
caller information. To save in the phonebook, see
55
7. Caller ID (KX-MB2025/KX-MB2030 only)
5
MSetN
To correct a mistake
1. Press MFN or MEN to move the cursor to the incorrect
Note:
number.
R If you assign an item to a station key which already
2. Press MStopN to delete the number.
3. Enter the correct number.
contains an item, the previous item will be replaced.
R Station 1 and 2 can be used alternatively as
To delete a number
Press MFN or MEN to move the cursor to the number you
want to delete and press MStopN.
7.4 Erasing caller information
7.4.1 Erasing all caller information
1 Press MMenuN repeatedly to display “CALLER
SETUP”. A MSetN
R “CALL LIST ERASE” will be displayed.
2
3
MSetN
R To cancel erasing, press MStopN, then MMenuN.
MSetN A MStopN
7.4.2 Erasing specific caller information
R Make sure that the MFaxN light is ON.
1
MCaller IDN
2 Press MCN or MDN repeatedly to display the desired
item. A MFN A MSetN A MStopN
7.5 Storing caller information
7.5.1 Into the one-touch dial feature and
phonebook
R Make sure that the MFaxN light is ON.
1
MCaller IDN
2 Press MCN or MDN repeatedly to display the desired
item.
3
MMenuN
4 Select the station key or phonebook.
For station 1–2:
1. Press the desired station key.
2. Press MCN or MDN repeatedly to select “DIAL
MODE”. A MSetN A MSetN
For station 3:
Press the station key. A MSetN
For station 4–6:
Press MLowerN, then press the desired station key.
A MSetN
For phonebook:
Press MFN or MEN. A MSetN
56
8. Programmable Features
8.1 Programming
8. . Programmable Features
MMenuN
MSetN
1
MMenuN
3 Press the appropriate selection to display the desired
setting.
R This step will vary depending on the feature.
4
MSetN
5 Press MMenuN to exit.
To select features through the web browser interface
(KX-MB2000/KX-MB2010/KX-MB2030, LAN
connection only)
You can change features through the web browser
interface instead of the unit.
1. Start Multi-Function Station. A [Utilities] A
[Configuration Web Page]
R You can also access the unit by entering its IP
address on the web browser.
2. Select the desired category from the menu bar.
[Device Configuration]: features of the unit
[Network Configuration]: network features
3. Type “root” as the user name, then enter the
4. Select the desired feature tab at the top of the right
frame.
5. Change the settings or edit the information.
R This step will vary depending on the feature.
6. [Submit]
R The new setting will be transferred to the unit.
7. Close the web browser.
Note:
R The settings displayed in the web browser will be
updated by clicking [Reload].
57
8. Programmable Features
8.2 Basic features
Feature/Code
Selection
Setting the date and time
Enter the date and time using the dial keypad. See page 22 for details.
MBNM1NM0NM1N
Setting your logo
MBNM1NM0NM2N
Enter your logo using the dial keypad. See page 23 for details.
(KX-MB2025/KX-MB2030
only)
Setting your fax number
MBNM1NM0NM3N
Enter your fax number using the dial keypad. See page 23 for details.
(KX-MB2025/KX-MB2030
only)
Selecting the language
MBNM1NM1NM0N
(KX-MB2000HX/
KX-MB2010HX/
KX-MB2025EX/KX-MB2030EX
only)
The display and reports will be in the selected language.
R The location setting must also match your location. See feature #114 on
M1N “ENGLISH”: English is used.
M2N “CZECH”: Czech is used.
M3N “SLOVAK”: Slovak is used.
M4N “HUNGARIAN”: Hungarian is used.
1. MMenuN A MBNM1NM1NM0N
2. Press M1N to M4N to select the desired language. A MSetN A MMenuN
Note:
R The default may vary depending on the model.
Selecting the location where
you use
MBNM1NM1NM4N
(KX-MB2025EX/
KX-MB2030EX only)
This setting must match your location.
M1N “CZECH” (default): To use in Czech.
M2N “SLOVAKIA”: To use in Slovakia.
M3N “HUNGARY”: To use in Hungary.
Setting the dialling mode
MBNM1NM2NM0N
(KX-MB2025/KX-MB2030
only)
M1N “PULSE”
M2N “TONE” (default)
Setting recall/flash time
MBNM1NM2NM1N
(KX-MB2025/KX-MB2030
only)
The recall/flash time depends on your telephone exchange or host PBX.
M0N “900ms”
M1N “700ms”
M2N “600ms”
M3N “400ms”
M4N “300ms”
M5N “250ms”
M6N “200ms”
M7N “160ms”
M8N “110ms”
M9N “100ms” (default)
MGN “90ms”
MBN “80ms”
Note:
R If the unit is connected via a PBX, PBX functions (transferring a call, etc.)
might not work correctly. Consult your PBX supplier for the correct setting.
Changing the LCD display
contrast
MBNM1NM4NM5N
M1N “NORMAL” (default)
M2N “DARKER”
58
8. Programmable Features
Feature/Code
Selection
Selecting the scale
M1N “MILLIMETRES” (default)
MBNM1NM4NM7N
M2N “INCHES”
Note:
R The selected scale will be used when measurements are shown on the
unit’s display.
Changing the password for
feature programming via
remote operation
1. MMenuN A MBNM1NM5NM5N A MSetN
2. Enter the current password. A MSetN
R The default password is “1234”.
MBNM1NM5NM5N
3. Enter a new 4-digit password using 0–9. A MSetN
4. Enter the new password again. A MSetN A MMenuN
Note:
R It is recommended that you change this password from the default
password.
R This password is also used for feature programming via a web browser
(KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only).
Setting the toner
maintenance time
MBNM1NM5NM8N
The unit will automatically activate for maintenance, once every 24 hours.
Because this is to prevent the toner from solidifying, the noise that the unit
makes during maintenance cannot be stopped. However, if the unit’s noise
bothers you, you can change the start time.
1. MMenuN A MBNM1NM5NM8N A MSetN
2. Enter the maintenance start time.
R The default time is “12:00”.
select AM or PM.
time entry.
3. MSetN A MMenuN
Resetting all features (and
deleting all data in memory)
MBNM1NM5NM9N
Before you dispose of, transfer or return the product, activate this feature to
reset all programmable features and to delete all data stored in memory.
KX-MB2025/KX-MB2030 only: Phonebook (or caller information) and fax
transmission data (journal report and faxes received in memory) will be deleted.
M0N “NO” (default)
M1N “YES”
R Disconnect the telephone line cord (KX-MB2025/KX-MB2030 only), USB
cable and LAN cable (KX-MB2000/KX-MB2010/KX-MB2030 only) before
activating this feature.
To reset all features:
1. MMenuN A MBNM1NM5NM9N
2. Press M1N to select “YES”. A MSetN
3. Press M1N to select “YES”. A MSetN
Setting the ringer pattern
MBNM1NM6NM1N
(KX-MB2025/KX-MB2030
only)
M1N “A” (default)
M2N “B”
M3N “C”
Setting the beep sounds and
keytones
MBNM1NM6NM5N
M0N “OFF”: Deactivate this feature.
M1N “ON” (default): You will hear confirmation/error beep sounds and keytones.
Note:
R Even if this feature is set to “OFF”, the unit beeps in the following cases:
–
the memory reception alert setting (feature #437 on page 65) is
activated (KX-MB2025/KX-MB2030 only).
–
the top cover is opened.
59
8. Programmable Features
Feature/Code
Selection
Changing the ring count in
FAX ONLY mode
MBNM2NM1NM0N
(KX-MB2025/KX-MB2030
only)
KX-MB2025EX/KX-MB2030EX:
M2N “2” (default)
M3N “3”
M4N “4”
M5N “5”
KX-MB2025FX/KX-MB2030FX:
M1N “1”
M2N “2” (default)
M3N “3”
M4N “4”
M5N “5”
M6N “6”
M7N “7”
M8N “8”
M9N “9”
Note:
R If you are using the unit with an answering machine, set to more than 4
Setting the Caller ID list to
print automatically
MBNM2NM1NM6N
(KX-MB2025/KX-MB2030
only)
M0N “OFF” (default): The unit will not print the Caller ID list, but will keep records
of the information for the last 30 callers.
M1N “ON”: The unit will print the Caller ID list automatically after every 30 new
Setting the time adjustment
MBNM2NM2NM6N
Using this feature, the unit’s date and time setting will be automatically adjusted
when caller information is received.
(KX-MB2025/KX-MB2030
only)
M1N “AUTO”: The date and time setting will be automatically adjusted.
M2N “MANUAL” (default): Deactivates this feature.
Setting the recording paper
size in the paper input tray
MBNM3NM8NM0N
M1N “LETTER”: Letter-size paper
M2N “A4” (default): A4-size paper
M4N “B5(ISO)”: B5(ISO)-size paper
M5N “B5(JIS)”: B5(JIS)-size paper
M6N “16K”: 16K-size paper
Note:
R When “B5(ISO)”, “B5(JIS)” or “16K” is selected, received fax
documents will be stored in memory (KX-MB2025/KX-MB2030 only).
Setting the recording paper
size in the manual input tray
MBNM3NM8NM1N
M1N “LETTER”: Letter-size paper
M2N “A4” (default): A4-size paper
M3N “LEGAL”: Legal-size paper
M4N “B5(ISO)”: B5(ISO)-size paper
M5N “B5(JIS)”: B5(JIS)-size paper
M6N “16K”: 16K-size paper
M7N “216X330”
M8N “216X340”
Note:
R When you set feature #147 to “INCHES”, the numbers are displayed in
inches.
60
8. Programmable Features
Feature/Code
Selection
Setting the recording paper
type for paper input tray
MBNM3NM8NM3N
M1N “PLAIN PAPER” (default):
75 g/m to 90 g/m paper.
M2N “THIN PAPER”:
2
2
2
2
64 g/m to 75 g/m paper.
Note:
R This setting will be deactivated when printing from a computer. To set the
recording paper type for printing, see page 29.
Setting the recording paper
type for manual input tray
MBNM3NM8NM4N
M1N “PLAIN PAPER” (default):
75 g/m to 90 g/m paper.
M2N “THIN PAPER”:
2
2
2
2
64 g/m to 75 g/m paper.
Note:
R This setting will be deactivated when printing from a computer. To set the
recording paper type for printing, see page 29.
Setting the waiting time for
the power save mode
MBNM4NM0NM3N
To set the length of time before the unit enters power save mode.
M1N “5min” (default): 5 minutes
M2N “15min”: 15 minutes
M3N “30min”: 30 minutes
M4N “1h”: 1 hour
Note:
R When in power save mode, the unit needs to preheat the fuser unit before
it can begin printing.
Holding the previous contrast M0N “DISABLED” (default): Deactivates this feature.
setting
MBNM4NM6NM2N
M1N “ENABLED”: The unit will hold the previous setting.
Note:
R The previous setting will be held individually for copying.
R The previous setting will be held individually for sending faxes (KX-MB2025/
KX-MB2030 only).
Setting the default operation
mode
To select the default operation mode when the selected time of the mode timer
(feature #464) passes.
MBNM4NM6NM3N
M1N “COPY” (default): Copy mode is selected as default.
(KX-MB2025/KX-MB2030
only)
M2N “FAX”: Fax mode is selected as default.
Note:
R You cannot select the scan mode using this feature.
Setting the default operation
mode timer
MBNM4NM6NM4N
(KX-MB2025/KX-MB2030
only)
To set the timer before returning to the default operation mode (feature #463).
M0N “OFF”: Deactivates this feature.
M1N “30s”: 30 seconds
M2N “1min” (default): 1 minute
M3N “2min”: 2 minutes
M4N “5min”: 5 minutes
Setting toner save feature
M0N “OFF” (default): Deactivates this feature.
MBNM4NM8NM2N
M1N “ON”: The toner cartridge will last longer.
Note:
R This feature may lower the print quality by reducing toner consumption.
R This setting is valid for copying, and when the unit automatically prints
reports/lists.
R This setting is invalid for printing received faxes (KX-MB2025/KX-MB2030
only).
61
8. Programmable Features
8.3 Fax features (KX-MB2025/KX-MB2030 only)
Feature/Code
Selection
Changing the TEL/FAX
delayed ring count
MBNM2NM1NM2N
If you use an extension telephone in TEL/FAX mode, select the desired number
of times the extension telephone rings before the unit answers the call.
KX-MB2025EX/KX-MB2030EX:
M2N “2” (default)
M3N “3”
M4N “4”
KX-MB2025FX/KX-MB2030FX:
M1N “1”
M2N “2” (default)
M3N “3”
M4N “4”
M5N “5”
M6N “6”
M7N “7”
M8N “8”
M9N “9”
Note:
Erasing all items stored for
the one-touch dial and
phonebook
M0N “NO” (default)
M1N “YES”
R Disconnect the telephone line cord, USB cable and LAN cable (KX-MB2030
MBNM2NM8NM9N
only) before activating this feature.
To erase all items:
1. MMenuN A MBNM2NM8NM9N
2. Press M1N to select “YES”. A MSetN
3. Press M1N to select “YES”. A MSetN A MMenuN
Printing a sending report
MBNM4NM0NM1N
M0N “OFF”: Sending reports will not be printed.
M1N “ON”: A sending report will be printed after every fax transmission.
M2N “ERROR” (default): A sending report will be printed only when fax
transmission fails.
Setting the journal report to
print automatically
MBNM4NM0NM2N
M0N “OFF”: The unit will not print a journal report, but will keep a record of the
last 30 fax transmissions and receptions.
M1N “ON” (default): The unit will print a journal report automatically after every
30 new fax transmissions and receptions (page 42).
in the manual answer setting
MBNM4NM0NM4N
62
8. Programmable Features
Feature/Code
Selection
Sending documents
overseas
MBNM4NM1NM1N
If you cannot send a fax overseas even if the number is correct and the line is
connected, activate this feature before sending the fax.
This feature improves the reliability by reducing the transmission speed.
M0N “OFF”: Deactivates this feature.
M1N “NEXT FAX”: This setting is effective only for the next attempted fax
transmission. After transmission, the unit will return to the previous setting.
M2N “ERROR” (default): When the previous fax transmission fails and you wish
to re-send the document.
Note:
R This feature is not available for broadcast transmission.
R Calling charges may be higher than usual.
Sending a fax at a specific
time
MBNM4NM1NM2N
This feature allows you to take advantage of low-cost calling hours offered by
your telephone company. This feature can be set up to 24 hours in advance of
the desired time.
M0N “OFF” (default)
M1N “ON”
To send a document:
1. If the MFaxN light is OFF, turn it ON by pressing MFaxN.
4. MMenuN A MBNM4NM1NM2N
5. Press M1N to select “ON”. A MSetN
6. Enter the fax number.
R To enter an item using one-touch dial feature and phonebook, see step
you do not have to press MPhonebookN before pressing MCN or MDN.)
7. MSetN
8. Enter the transmission start time.
select AM or PM.
time entry.
9. When using the scanner glass, press MSetN. A MStartN
When using the automatic document feeder, press MSetN.
R The document will be fed into the unit and scanned into memory. The
unit will then send the data at the specified time. You cannot use this
feature for another fax transmission until the former sending is
completed.
Note:
R To cancel this setting after programming, press MStopN while the unit is idle,
and then press MSetN.
Setting the Error Correction
Mode (ECM)
This feature is available when the sending / receiving fax machines are ECM
compatible.
MBNM4NM1NM3N
M0N “OFF”: Deactivates this feature.
M1N “ON” (default): Fax transmission / reception will be carried out so that the
errors do not occur.
63
8. Programmable Features
Feature/Code
Selection
Setting the connecting tone
MBNM4NM1NM6N
If you often have trouble when sending faxes, this feature allows you to hear
connecting tones: fax tone, ring back tone and busy tone. You can use these
tones to confirm the status of the other party’s machine.
M0N “OFF”: Deactivates this feature.
M1N “ON” (default): You will hear connecting tones.
Note:
R If the ring back tone continues, the other party’s machine may not be a fax
machine or may have run out of paper. Check with the other party.
R The connecting tone volume cannot be adjusted.
Setting the maximum fax
speed
MBNM4NM1NM8N
M1N “14.4Kbps”
M2N “33.6Kbps” (default)
Note:
R The fax speed maybe lower than the selected speed depending on your line.
Setting auto reduction
feature
MBNM4NM3NM2N
To receive a fax document that is longer than your recording paper.
M0N “OFF”: The unit will print received documents at their original size.
M1N “ON” (default): The unit will fit received documents onto your recording
paper.
Changing the fax activation
code
If you wish to use an extension telephone to receive faxes, activate this feature
and program the activation code.
MBNM4NM3NM4N
Important:
R The fax activation code must be different from the code that you
programmed on the answering machine.
M0N “OFF”
M1N “ON” (default)
1. MMenuN A MBNM4NM3NM4N
2. Press M1N to select “ON”. A MSetN
3. Enter your code from 2 to 4 digits, using 0–9, MGN and MBN.
R The default code is “H#9”.
R Do not enter “0000”.
4. MSetN A MMenuN
Changing the silent fax
recognition ring count
MBNM4NM3NM6N
To change the number of times the unit rings while in TEL/FAX mode.
M3N “3” (default)
M4N “4”
M5N “5”
M6N “6”
M7N “7”
M8N “8”
M9N “9”
Note:
64
8. Programmable Features
Feature/Code
Selection
Setting the memory reception To alert you with a beeping sound when a received fax document is stored into
alert
memory.
MBNM4NM3NM7N
M0N “OFF”: Deactivates this feature.
M1N “ON” (default): You will hear a beeping sound.
Note:
R If documents are stored into memory due to some printing problem, the
beeps will continue until you solve the problem. If a message is displayed,
see page 81 to page 83 for directions on printing out the stored
documents. Make sure the unit is supplied with enough paper to print the
stored document.
R If documents are stored into memory due to activating the web fax preview
to beep when the memory is nearly full (KX-MB2030 only).
Setting friendly reception
MBNM4NM3NM8N
To receive a fax automatically when you answer a call and hear a fax calling
tone (slow beep).
M0N “OFF”:
You have to press MStartN, and then M2N for fax reception.
M1N “ON” (default):
You do not have to press MStartN, and then M2N for fax reception.
Receiving a fax into the
computer
If you wish to receive a fax into a computer, activate this feature and run [PC
FAX] from Multi-Function Station.
MBNM4NM4NM2N
This feature is available when the fax preview mode is turned OFF (feature #448
M0N “OFF”: Deactivates this feature.
M1N “ALWAYS”: If the unit recognizes the connection to the computer, it will
transfer received documents to the computer. If the unit cannot recognize the
connection, it will store received documents into memory, and then transfer the
data after recognition of the computer connection.
M2N “CONNECTED” (default): If the unit recognizes the connection to the
computer, it will transfer received documents to the computer. If the unit cannot
recognize the connection, it will print the data.
Setting the computer for PC
fax reception
To select the computer that will be used for receiving a fax. See page 24 for
details.
MBNM4NM4NM3N
(KX-MB2030 only)
MBNM4NM4NM8N
(KX-MB2030 only)
Setting the web fax preview
access code
MBNM4NM5NM0N
(KX-MB2030 only)
Setting notification of fax
reception
MBNM4NM5NM1N
M0N “OFF” (default): Deactivates this feature.
M1N “ON”: The computer connected to your unit using USB/LAN will receive a
notification when a fax document is received.
Note:
R For LAN connection (KX-MB2030 only): Register computers to which fax
reception notifications will be sent through the web browser interface
65
8. Programmable Features
Feature/Code
Selection
Resetting fax features to their M0N “NO” (default)
default settings
MBNM4NM5NM9N
M1N “YES”
To reset the fax features:
1. MMenuN A MBNM4NM5NM9N
2. Press M1N to select “YES”. A MSetN A MSetN A MMenuN
Note:
(KX-MB2030 only).
R If you select “YES”, the unit will automatically print out any received fax
documents that have been stored into memory:
–
–
Fax preview (feature #448 on page 53) (KX-MB2030 only).
Setting the PC information for Select the PC to send fax reception notification message to (up to 6
notification of fax reception
(KX-MB2030, LAN connection
only)
R This feature can be
programmed only through
the web browser interface.
destinations).
1. Start Multi-Function Station.
2. [Utilities] A [Configuration Web Page] A [Device Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
4. Select the [FAX FEATURE] tab.
5. Click [Edit] next to [RECEIVE PC LIST].
6. Click [List] next to the desired destination.
7. Click the desired PC from the list. A [Submit]
8. Close the web browser.
66
8. Programmable Features
8.4 Copy features
Feature/Code
Selection
Setting the input tray to use
for copy
MBNM4NM6NM0N
M1N “#1” (default): The paper input tray is selected. The displayed paper size
depends on the recording paper size setting (feature #380 on page 60).
M2N “#2”: The manual input tray is selected. The displayed paper size depends
on the recording paper size setting (feature #381 on page 60).
Changing the default copy
resolution
MBNM4NM6NM1N
To change the default resolution setting for copying.
M1N “TEXT/PHOTO” (default): For documents containing both text and
photographs.
M2N “TEXT”: For documents containing only text.
M3N “PHOTO”: For documents containing photographs, shaded drawings, etc.
Holding the previous page
layout setting
MBNM4NM6NM7N
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: The unit will hold the previous setting.
Holding the previous zoom
setting
MBNM4NM6NM8N
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: The unit will hold the previous setting.
Holding the previous collate
setting
MBNM4NM6NM9N
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: The unit will hold the previous setting.
Holding the previous edge
setting
MBNM4NM7NM3N
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: The unit will hold the previous setting.
Setting the frame margin
MBNM4NM7NM4N
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: Your copies will be automatically reduced according to the
margin setting.
Holding the previous margin
setting
MBNM4NM7NM5N
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: The unit will hold the previous setting.
67
8. Programmable Features
8.5 PC print features
Feature/Code
Selection
Changing the data timeout
setting
The unit will automatically print the remaining data in memory when the
computer does not send data to the unit during the set time.
MBNM7NM7NM4N
1. MMenuN A MBNM7NM7NM4N A MSetN
2. Enter the desired data timeout setting from “005” seconds to “600”
seconds, using the dial keypad.
R The default setting is “060” seconds.
3. MSetN A MMenuN
Setting mutual A4/letter print
MBNM7NM7NM6N
This feature allows printing in A4-size even if letter-size recording paper is
loaded in the paper input tray, and vice versa.
M0N “OFF”: Deactivates this feature.
M1N “ON” (default): Printing is possible between A4/letter-size.
68
8. Programmable Features
8.6 Scan features
Feature/Code
Selection
Setting the scan mode for
Push Scan
M1N “VIEWER” (default): The scanned image will be displayed in the
[Multi-Function Viewer] window.
MBNM4NM9NM3N
M2N “FILE”: The scanned image will be saved as a file.
M3N “EMAIL”: The scanned image will be saved for email attachment.
M4N “OCR”: The scanned image will be displayed in the OCR window.
M5N “EMAIL ADDRESS”: The scanned image will be sent as an attachment
without using email software.
M6N “FTP SERVER”: The scanned image will be sent to the pre-programmed
folder on the FTP server.
M7N “SMB FOLDER”: The scanned image will be sent to the pre-programmed
SMB folder.
Note:
R Following selections will be displayed only when the server setting is
programmed through the web browser interface in advance (KX-MB2000/
KX-MB2010/KX-MB2030 only).
–
–
–
“EMAIL ADDRESS” will be displayed when the email server setting is
“FTP SERVER” will be displayed when the FTP server setting is
“SMB FOLDER” will be displayed when the SMB folder setting is
Holding the previous
scanning parameter for Push
Scan
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: The unit will hold the previous scan settings for each mode of
push scan.
MBNM4NM9NM4N
Setting the information for
scan to email address
(KX-MB2000/KX-MB2010/
KX-MB2030, LAN connection
only)
R This feature can be
programmed only through
the web browser interface.
When you send scanned files as email attachments directly from this unit, you
need to program the email server and SMTP server settings beforehand.
Consult your service provider or network administrator for details.
1. Start Multi-Function Station.
2. [Utilities] A [Configuration Web Page] A [Device Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
4. Select the [SCAN FEATURE] tab.
5. Click [Edit] next to [EMAIL SERVER].
6. Enter the email server and SMTP server information. A [Submit]
7. Close the web browser.
69
8. Programmable Features
Feature/Code
Selection
Registering the scan to email When you send scanned files as email attachments directly from this unit, you
address destinations
(KX-MB2000/KX-MB2010/
KX-MB2030, LAN connection
only)
R This feature can be
programmed only through
the web browser interface.
can register email destinations (up to 30 destinations) for the unit through the
web browser interface in advance.
1. Start Multi-Function Station.
2. [Utilities] A [Configuration Web Page] A [Device Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
4. Select the [SCAN FEATURE] tab.
5. Click [Edit] next to [SEND USER].
6. Click [Edit] next to the desired scan to email user.
7. Enter the name and email address.
R Select the station key number from the drop-down list if necessary
(KX-MB2030 only).
8. [Submit]
9. Close the web browser.
Setting the information for
scan to FTP (KX-MB2000/
KX-MB2010/KX-MB2030, LAN
connection only)
When you send scanned files to an FTP server, you can register the FTP
destinations (up to 6 destinations) to the unit through the web browser interface.
1. Start Multi-Function Station.
2. [Utilities] A [Configuration Web Page] A [Device Configuration]
R This feature can be
3. Type “root” as the user name, then enter the password (feature #155 on
programmed only through
the web browser interface.
4. Select the [SCAN FEATURE] tab.
5. Click [Edit] next to [FTP SERVER].
6. Click [Edit] next to the desired FTP server.
7. Enter the server name, IP address, folder directory, etc. A [Submit]
8. Close the web browser.
Note:
saved in the root folder.
Setting the information for
scan to SMB folder
When you send scanned files to an SMB folder, you can register the SMB folder
destinations (up to 6 destinations) to the unit through the web browser interface.
(KX-MB2000/KX-MB2010/
KX-MB2030, LAN connection
only)
R This feature can be
programmed only through
the web browser interface.
1. Start Multi-Function Station.
2. [Utilities] A [Configuration Web Page] A [Device Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
4. Select the [SCAN FEATURE] tab.
5. Click [Edit] next to [SMB FOLDER].
6. Click [Edit] next to the desired SMB folder.
7. Enter the folder name, folder directory, domain name, etc. A [Submit]
8. Close the web browser.
70
8. Programmable Features
8.7 LAN features (KX-MB2000/KX-MB2010/KX-MB2030 only)
Feature/Code
Selection
LAN setting with a DHCP
server
MBNM5NM0NM0N
M0N “DISABLED”: Deactivates this feature.
M1N “ENABLED” (default): The following will be allocated automatically using a
DHCP (Dynamic Host Configuration Protocol) server.
–
–
–
IP address
Subnet mask
Default gateway
Setting the IP address for the This feature is available when feature #500 is deactivated.
LAN connection
MBNM5NM0NM1N
1. MMenuN A MBNM5NM0NM1N A MSetN
2. Enter the IP address of the unit on the LAN using the dial keypad. A
MSetN A MMenuN
Setting the Subnet mask for
the LAN connection
MBNM5NM0NM2N
This feature is available when feature #500 is deactivated.
1. MMenuN A MBNM5NM0NM2N A MSetN
2. Enter the subnet mask of the network on the LAN using the dial keypad.
A MSetN A MMenuN
Setting the default gateway
for the LAN connection
MBNM5NM0NM3N
This feature is available when feature #500 is deactivated.
1. MMenuN A MBNM5NM0NM3N A MSetN
2. Enter the default gateway of the network on the LAN using the dial keypad.
A MSetN A MMenuN
Setting the primary DNS
server for the LAN
connection
This feature is available when feature #500 is deactivated.
1. MMenuN A MBNM5NM0NM4N A MSetN
2. Enter the primary DNS server of the network on the LAN using the dial
MBNM5NM0NM4N
keypad. A MSetN A MMenuN
Setting the secondary DNS
server for the LAN
connection
This feature is available when feature #500 is deactivated.
1. MMenuN A MBNM5NM0NM5N A MSetN
2. Enter the secondary DNS server of the network on the LAN using the dial
MBNM5NM0NM5N
keypad. A MSetN A MMenuN
Setting the machine name
1. MMenuN A MBNM5NM0NM7N A MSetN
MBNM5NM0NM7N
2. Enter the name of the unit to recognize on the LAN, up to 15 characters,
R The following symbols can also be entered.
! @ # $ % ^ & ’ ) ( . – _ { }
3. MSetN A MMenuN
Note:
R In order to recognize the unit on the LAN, the default name of the unit is
assigned automatically. If you change the name, assign a unique name to
avoid overlapping.
Displaying the MAC address
of the unit
MBNM5NM0NM8N
1. MMenuN A MBNM5NM0NM8N A MSetN
2. The MAC address of the unit will be displayed. A MMenuN
71
8. Programmable Features
Feature/Code
Selection
IP filtering for the LAN
connection
MBNM5NM3NM2N
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: The unit will deny/approve access from the pre-programmed
IP patterns. You can program whether to deny or approve IP addresses. Up to
4 patterns each for IPv4 and IPv6 can be programmed through the web browser
interface.
1. Start Multi-Function Station.
2. [Utilities] A [Configuration Web Page] A [Network Configuration]
3. Type “root” as the user name, then enter the password (feature #155 on
4. Select the [LAN FEATURE] tab.
5. Click [Edit] next to [IP FILTERING].
6. Click [Edit] next to [FILTER (IPv4)]/[FILTER (IPv6)].
7. Change the mode and edit IP filtering information. A [Submit]
8. Close the web browser.
Setting the IP address
automatically for the LAN
connection
This feature will be displayed only when feature #500 is activated.
M0N “DISABLED” (default): Deactivates this feature.
M1N “ENABLED”: IP address will be allocated automatically without using a
DHCP (Dynamic Host Configuration Protocol) server.
MBNM5NM3NM3N
Setting HTTPD for the LAN
connection
MBNM5NM3NM4N
M0N “DISABLED”: Denies access to the web browser.
M1N “ENABLED” (default): Allows access to the web browser.
IPv6 protocol
M0N “DISABLED” (default): Deactivates this feature.
MBNM5NM3NM5N
M1N “ENABLED”: IPv6 protocol can be used. After installing the printer driver,
be sure to change the port to IPv6 protocol. You can check the IPv6 protocol
Note:
R To activate this feature, you need to turn the power switch of the unit OFF,
then ON.
Setting the primary WINS
server for the LAN
connection
This feature is available when feature #500 is deactivated.
1. MMenuN A MBNM5NM3NM8N A MSetN
2. Enter the primary WINS server of the network on the LAN using the dial
MBNM5NM3NM8N
keypad. A MSetN A MMenuN
Setting the secondary WINS
server for the LAN
connection
This feature is available when feature #500 is deactivated.
1. MMenuN A MBNM5NM3NM9N A MSetN
2. Enter the secondary WINS server of the network on the LAN using the dial
MBNM5NM3NM9N
keypad. A MSetN A MMenuN
72
8. Programmable Features
Feature/Code
Selection
Erasing all email addresses,
FTP destinations, and SMB
folder destinations stored in
the unit
M0N “NO” (default)
M1N “YES”
R Disconnect the telephone line cord (KX-MB2030 only), USB cable and LAN
cable before activating this feature.
MBNM5NM7NM8N
To erase all email addresses:
1. MMenuN A MBNM5NM7NM8N
2. Press M1N to select “YES”. A MSetN
3. Press M1N to select “YES”. A MSetN A MMenuN
To erase FTP destinations:
1. MMenuN A MBNM5NM7NM8N
2. Press M1N to select “YES”. A MSetN
3. Press M0N to select “NO”. A MSetN
4. Press M1N to select “YES”. A MSetN A MMenuN
To erase SMB folder destinations:
1. MMenuN A MBNM5NM7NM8N
2. Press M1N to select “YES”. A MSetN
3. Press M0N to select “NO”. A MSetN
4. Press M0N to select “NO”. A MSetN
5. Press M1N to select “YES”. A MSetN A MMenuN
73
8. Programmable Features
8.8 Network features (KX-MB2000/KX-MB2010/KX-MB2030, LAN
connection only)
These features can be programmed through the web browser interface.
Feature
Tab
Selection
Setting the LAN features [LAN FEATURE]
Setting the community
name for SNMP
[SNMP]
[SNMP]
Enter the SNMP community name. Consult your service
provider or network administrator for details.
Setting the location
Enter the location information of the unit.
where you use this unit
Displaying the link local [IPv6]
address for IPv6
The link local address will be displayed.
Displaying the IPv6
address for auto
configuration
[IPv6]
The IP address for auto configuration will be displayed.
Setting the IP address
for IPv6
[IPv6]
Enter the IP address for IPv6. Consult your service
provider or network administrator for details.
Setting the default
router for IPv6
[IPv6]
Enter the default router address for IPv6. Consult your
service provider or network administrator for details.
Setting the information
for scan to FTP
[FTP FEATURE]
Enter the FTP server information to send scanned
images from the unit to an FTP server. See page 70 for
details.
Setting the information
for scan to SMB
[SMB FEATURE]
[EMAIL FEATURE]
[EMAIL FEATURE]
[ERROR NOTIFY]
Enter the SMB folder information to send scanned
images from the unit to an SMB folder. See page 70 for
details.
Setting the information
for scan to email
address
Enter the email server and SMTP server information to
send scanned images from the unit via an email. See
Registering the scan to
email address
destinations
Register email address destinations (up to 30
Setting the error notify
feature
[ENABLED]: The unit will send an email to registered
destinations when a problem occurs.
[DISABLED] (default): Deactivates this feature.
Setting the email server [ERROR NOTIFY]
information for the error
Enter the email server and SMTP server information to
send error notification emails to.
notify feature
Registering
destinations for the
error notify feature
[ERROR NOTIFY]
Enter the email address to which error notifications will
be sent and select the types of problems.
[LIFE WARNING]: A warning indicating that the toner
cartridge or drum cartridge needs to be replaced soon.
[MEDIA PATH ERROR]: An error indicating that there
is a problem with the paper input tray/manual input tray.
[LIFE ERROR]: An error indicating that the toner
cartridge or drum cartridge needs to be replaced.
74
9. Useful Information
D Lowercase letters
9.1 Character entry
The dial keypad is used to enter characters and
*1
When you enter email address (i.e. scan to email
will be displayed first (KX-MB2000/KX-MB2010/
KX-MB2030, LAN connection only).
9. . Useful Information
numbers.
–
–
–
Press MFN or MEN to move the cursor.
Press the dial keys to enter characters and numbers.
Press MStopN to erase the character or number
highlighted by the cursor. Press and hold MStopN to
erase all characters or numbers.
R If you press MDN, the order will be reversed.
2. Press MEN to insert the displayed character.
–
To enter another character located on the same dial
key, press MEN to move the cursor to the next space,
then press the appropriate dial key.
Keypad
Characters
M1N
M2N
M3N
M4N
M5N
M6N
M7N
M8N
M9N
M0N
MGN
1
/
.
_
,
–
`
[
:
]
;
{
}
|
+
=
B
b
E
e
?
A
a
D
d
G
g
J
j
C 2
c
F
f
2
3
3
4
4
5
5
H I
h
K
k
i
L
l
M N O 6
m n
o
6
P
p
T
t
Q R S
7
7
q
r
s
8
8
Z
z
)
U V
u
v
W X
Y
y
9
9
<
I
w
0
$
x
@ (
>
^
!
’
"
#
% &
¥
®
To switch between uppercase
or lowercase letters.
MFlashN
Hyphen
(KX-MB2025/
KX-MB2030 only)
MZoomN
To insert a space.
MStopN
To delete a character.
To select characters using MCN or MDN
Instead of pressing the dial keys, you can select
characters using MCN or MDN.
1. Press MCN repeatedly to display the desired
character. Characters will be displayed in the
following order:
A Uppercase letters
B Numbers
C Symbols
75
9. Useful Information
R When another person is adjusting stored data in the
unit, it may be overwritten. Make sure the unit is not
currently being used for the same function.
9.2 Status of the unit
9.2.1 Using Remote Control
9.2.2 Using Device Monitor
You can easily operate the following functions from your
computer.
You can confirm the setting information and current
status of the unit from your computer.
–
1 Start Multi-Function Station.
KX-MB2025/KX-MB2030 only:
–
–
Storing, editing or erasing items in directories
Storing or erasing items for broadcast transmission
Viewing items in the journal report (page 42)
Saving the journal report on your computer
Viewing items in the Caller ID list (page 55)
Storing caller information into directories (page 56)
Saving the Caller ID list on your computer
2 [Utilities] A [Device Monitor]
R The [Device Monitor] window will appear.
3 Confirm the status of the unit.
[Status]: Current status of the unit
–
–
–
–
–
Note:
R Additional information (toner and recording paper
status, unit information, etc.) will be displayed in
[Status] tab by clicking [Advanced Information].
R You can update the status of the unit by clicking
1 Start Multi-Function Station. A [Remote Control]
R The [Multi-Function Remote Control] window
will appear.
[Refresh].
R If a printing error occurs, the Device Monitor will start
automatically and display the error information.
R For details, see the help file by selecting [ ] from
Multi-Function Station.
9.2.3 Using the web browser (KX-MB2000/
KX-MB2010/KX-MB2030, LAN connection
only)
You can confirm the setting information and status of the
unit from the web browser.
1 Start Multi-Function Station. A [Utilities] A
[Configuration Web Page]
R You can also access the unit by entering its IP
address in a web browser.
2 Select a category from the menu bar.
[Status]: Toner and paper information, etc.
[Device]: Current status of the unit, etc.
[Network]: Network information, etc.
* The pictured model is KX-MB2025/KX-MB2030.
2 Select the desired tab (KX-MB2025/KX-MB2030
only).
R When you select [Device] or [Network], you can
change which features are displayed by clicking
the feature tabs at the top of the right frame.
R The latest data in the unit will be displayed.
3 Perform the desired operation.
3 Confirm the status of the unit.
R For details about each function, click [Help].
R To stop the operation, click [Cancel].
Note:
R You can update the status of the unit by clicking
4 [OK]
[Reload].
R You can also click [Apply] to continue the next
operation without closing the window.
[OK]
R The new data will be transferred to the unit and
the window will close.
Note:
R Some of the features cannot be programmed from
your computer.
R For details, see the help file by selecting [ ] from
Multi-Function Station.
76
9. Useful Information
9.3 Cancelling the operations
You can cancel the current operation from the unit. You
9.4 Handset unit (KX-MB2025/
KX-MB2030 only)
Important:
can also select the desired operation to cancel.
1
MStopN
R Before installing or removing the handset unit, be
R “USER STOPPED” is displayed.
sure to turn the power switch OFF.
R If “USER STOPPED” is not displayed, go to step
1 Connect the handset cord (A).
2 To cancel printing:
Press MStopN repeatedly to display “STOP
PRINTING?”.
To cancel scanning (KX-MB2025/KX-MB2030
only):
Press MStopN repeatedly to display “STOP
SCANNING?”.
To cancel copying:
A
Press MStopN repeatedly to display “STOP
COPYING?”.
2 Connect the handset connector (B).
R Remove the seal from the handset unit
connection jack if attached.
To cancel sending or receiving faxes
(KX-MB2025/KX-MB2030 only):
Press MStopN repeatedly to display “STOP FAX?”.
To cancel broadcast transmission (KX-MB2025/
KX-MB2030 only):
Press MStopN repeatedly to display “BROAD
CANCELLED?”.
To cancel fax redialling (KX-MB2025/KX-MB2030
only):
B
Press MStopN repeatedly to display “SEND
CANCELLED?”.
3
MSetN
77
9. Useful Information
3 Insert the tab (C) and rib (D).
D
To remove the handset unit
1. Pull the handset unit slightly forward (A), then lift it
in the direction of the arrow (B) to remove the rib.
B
A
C
2. Remove the tab (C), then disconnect the handset
connector (D).
D
C
9.5 Making a phone call using
one-touch dial feature or
phonebook (KX-MB2025/
KX-MB2030 only)
Before using this feature, store the desired names and
telephone numbers in one-touch dial feature and
phonebook (page 43).
Caution:
R When moving the unit, be sure to hold by the grip.
Do not hold by the handset unit.
Correct
Incorrect
R Make sure that the MFaxN light is ON.
9.5.1 Using one-touch dial feature
1 Press MMonitorN or lift the handset.
2 Select the desired station key.
For station 1–3:
Press the desired station key.
For station 4–6:
Note:
Press MLowerN, then press the desired station key.
R The unit will start dialling automatically.
R While talking to the other party, you can send a fax
using the scanner glass by pressing MStartN, and
then M1N (To receive a fax, press M2N).
9.5.2 Using the phonebook
1 Press MPhonebookN.
R Confirm that there are no documents in the
document entrance.
2 Press MCN or MDN repeatedly to display the desired
item.
3 Press MMonitorN or lift the handset.
R The unit will start dialling automatically.
78
9. Useful Information
To search for a name by initial
Example: “LISA”
1. MPhonebookN
2. Press MCN or MDN to initiate the phonebook.
3. Press M5N repeatedly to display any name with the
R To search for symbols, press MGN.
4. Press MCN or MDN repeatedly to display “LISA”.
R To stop the search, press MStopN.
R To dial the displayed party, press MMonitorN or lift
the handset.
79
10. Help
10.1 Report messages (KX-MB2025/KX-MB2030 only)
To indicate the unit’s fax transmission/reception status, one of the following messages will be printed on the sending
1
0
.
.
H
e
l
p
and journal reports (page 42).
Message
Code
Cause & Solution
COMMUNICATION ERROR
40-42
46-72
FF
R A transmission or reception error occurred. Try
again or check with the other party.
43
44
R A line problem occurred. Connect the telephone line
cord to a different jack and try again.
R An overseas transmission error occurred. Try using
the overseas mode (feature #411 on page 63).
DOCUMENT JAMMED
-----
ERROR-NOT YOUR UNIT
53
54
59
70
R A transmission or reception error occurred because
of a problem with the other party’s fax machine.
Check with the other party.
JUNK FAX PROH. REJECT
MEMORY FULL
-----
R The junk fax prohibitor feature of this unit rejected
fax reception.
-----
R The memory is full of received documents due to a
lack of recording paper or a recording paper jam.
to “ALWAYS”, check the connection between the
computer and the unit.
R If your unit is connected to the computer via the LAN
and the fax preview mode (feature #448 on
documents on the web browser, and then erase
unnecessary documents (page 53).
NO DOCUMENT / FAILED PICKUP
OTHER FAX NOT RESPONDING
-----
-----
R The document was not fed into the unit properly.
Re-insert it and try again.
R The other party’s fax machine is busy or has run out
of recording paper. Try again.
R The other party’s fax machine rings too many times.
R The other party’s machine is not a fax machine.
Check with the other party.
R The number you dialled is not in service.
PRESSED THE ‘Stop’ KEY
-----
R
MStopN was pressed and fax communication was
cancelled.
THE COVER WAS OPENED
OK
-----
-----
R The top cover was opened. Close it and try again.
R Fax transmission or reception was successful.
80
10. Help
10.2 Display messages
To indicate the unit’s status, one or more of the following messages will appear on the display.
Display
Cause & Solution
“CALL SERVICE”
R There is something wrong with the unit. Contact our service personnel.
“CHANGE DRUM”
R There is something wrong with the drum cartridge. Replace the drum
cartridge and the toner cartridge.
“CHECK DOCUMENT”
R The document was not fed into the unit properly. Remove the document,
and then press MStopN to clear the message. Re-insert the document. If
misfeeding occurs frequently, clean the document feeder rollers
“CHECK DRUM”
“CHECK PAPER #1”
R Recording paper is not installed or the paper input tray has run out of paper.
R Recording paper was not fed into the unit properly. Re-insert the recording
R The paper input tray is not installed or is not inserted completely. Insert the
paper input tray into the unit.
“CHECK PAPER TRAY #1”
R The loaded recording paper is not the appropriate size. Load recording
paper of the size that is shown on the display.
R If this message is often displayed, also change the recording paper size
“B5(ISO)”, “B5(JIS)” or “16K”, so received faxes have been stored into
memory. Change the recording paper size setting and load the appropriate
recording paper.
Note:
R “#1”: Check the paper input tray. The displayed paper size depends on the
recording paper size setting (feature #380 on page 60).
R “#2”: Check the manual input tray. The displayed paper size depends on
the recording paper size setting (feature #381 on page 60).
“CHECK PICK UP INPUT
R Recording paper was not fed into the unit properly. Load the paper again
TRAY #2”
“CHECK REAR COVER”
R The manual input tray (rear cover) is open. Close it.
R A recording paper jam occurred near the manual input tray (rear cover).
Remove the jammed paper (page 92).
“COOL DOWN FUSER”
R The unit is cooling down the fuser unit. Wait for a while.
“DRUM LIFE LOW REPLACE
R The drum is reaching the end of its life. Replace the drum cartridge and the
toner cartridge as soon as possible.
SOON”
“EMAIL SIZE OVER”
R When performing scan to email address, the total file size of scanned data
exceeded the file size limitation. Divide the document into sections.
81
10. Help
Display
Cause & Solution
“FAX IN MEMORY”
R The unit has a document in memory. See the other displayed message
instructions to print out the document. For fax memory capacity, see
–
–
check the connection between the computer and the unit.
check that the computer is turned ON.
R If your unit is connected to the computer via the LAN and the fax preview
–
–
view, print or save the received fax documents, and then erase the
unnecessary documents (page 53).
turn the setting to “OFF”. The fax documents stored in memory will be
printed automatically.
“FILE SIZE OVER”
R When performing scan to FTP server or scan to SMB folder, the total file
size of scanned data exceeded the file size limitation. Divide the document
into sections.
“KEEP COPYING”
R Copying has stopped due to some existing problem (Example: a lack of
recording paper or a recording paper jam). See the other displayed message
instructions to continue copying.
“LOW TEMP.”
R The inside of the unit is extremely cold and cannot be operated. Use the unit
in a warmer area.
“MEMORY FULL”
R When performing memory transmission, the document being stored
exceeded the memory capacity of the unit. Send the entire document
manually.
R When making a copy, the document being stored exceeded the memory
capacity of the unit. Press MStopN to clear the message. Divide the
document into sections.
“MODEM ERROR”
R There is something wrong with the unit’s modem. Contact our service
personnel.
“NO FAX REPLY”
R The other party’s fax machine is busy or has run out of recording paper. Try
again.
“OUT OF PAPER INPUT TRAY R Recording paper is not loaded in the manual input tray. Load paper
#2”
“PAPER IN TRAY #2”
“PAPER JAMMED”
“OPEN TOP COVER”
“PC FAIL OR BUSY”
R The cable or the computer power cord is not connected correctly. Check the
R The software is not running on the computer. Restart the software and try
again.
“PHONEBOOK FULL”
R There is no space to store new items in the phonebook. Erase unnecessary
“PLEASE WAIT”
R The unit is warming up. Wait for a while.
“POLLING ERROR”
R The other party’s fax machine does not offer the polling function. Check with
the other party.
“REDIAL TIME OUT”
R The other party’s fax machine is busy or has run out of recording paper. Try
again.
“REMOVE DOCUMENT”
R Attempted to send or copy a document longer than 600 mm using the
automatic document feeder. Press MStopN to remove the document. Divide
the document into two or more sheets and try again.
82
10. Help
Display
Cause & Solution
“REMOVE PAPER IN INPUT
TRAY #2”
R The recording paper is installed in the manual input tray when trying to
receive faxes or print reports. Remove the recording paper from manual
input tray.
“REPLACE DRUM CHANGE
R The drum cartridge’s service life is finished. Replace the drum cartridge and
the toner cartridge immediately.
SUPPLIES”
“RX MEMORY FULL”
R The memory is full of received documents due to a lack of recording paper
or a recording paper jam. Load paper (page 14) or remove the jammed
–
–
check the connection between the computer and the unit.
check that the computer is turned ON.
R If your unit is connected to the computer via the LAN and the fax preview
–
–
view, print or save the received fax documents, and then erase the
unnecessary documents (page 53).
turn the setting to “OFF”. The fax documents stored in memory will be
printed automatically.
“SCANNER POSITION
ERROR”
R There is something wrong with the scanner position. Turn the power switch
OFF, then ON. If the problem cannot be solved, contact our service
personnel.
“TONER EMPTY”
R The toner is empty. Replace the toner cartridge immediately.
“CHANGE SUPPLIES”
“TONER LOW”
R The toner is reaching the end of its life. You will need to replace the toner
cartridge soon.
“CHANGE SUPPLIES”
“TOP COVER OPEN”
R The top cover is open. Close it.
“TRANSMIT ERROR”
R A transmission error occurred. Try again.
83
10. Help
10.3 When a function does not work
10.3.1 General
Problem
Cause & Solution
The unit does not work.
The output tray becomes full
quickly or the recording paper
does not stack properly on
the output tray.
R High humidity may cause the recording paper to curl. Try turning the paper
over and re-inserting it. If the curl on the paper is heavy, please remove it
from the output tray. If you still have this problem, contact our service
personnel.
I cannot adjust the volume,
display items stored in the
one-touch dial and
R The unit is set to scan mode or copy mode. Press MFaxN to switch modes.
If you still have this problem, contact our service personnel.
phonebook or display Caller
ID information (KX-MB2025/
KX-MB2030 only).
A printing error is displayed
while using PC FAX
R The printer driver is used for PC FAX and Remote Control. Transmission
errors will be displayed as printing errors.
(KX-MB2025/KX-MB2030
only) and Remote Control.
Multi-Function Station does
not work properly.
R If the USB cable is connected to a USB hub, connect the cable directly to
the USB port on your computer.
R Make sure you have installed the latest Service Pack available for the
version of Windows installed on your computer. See the Microsoft web site
for details.
R If you have any other multifunction software installed on your computer,
uninstall it.
R Check that your computer has enough memory and hard disk space. If your
computer warns that there is insufficient memory, close other applications.
If there is not enough space on the hard disk, delete unnecessary files.
R Uninstall Multi-Function Station once, and re-install it.
I cannot install or uninstall
Multi-Function Station.
R Some of the files needed to install or uninstall Multi-Function Station may
be corrupted. Use the MfsCleaner utility (found on the supplied CD-ROM)
to solve the problem.
1. Insert the supplied CD-ROM into your CD-ROM drive.
R The setup program will start automatically.
2. [Tools] A [Cleanup Tool]
R The [MfsCleaner] window will appear.
3. Click [Clean], and then click [Yes] to restart the computer.
Note:
I cannot view the operating
instructions using
Multi-Function Station.
I cannot find the unit in the
[Target Device] or [Device
Select] dialogue box when
operating the following
functions.
R The printer driver has not been installed. Install it on your computer
–
–
–
Scanning
Remote Control
PC FAX (KX-MB2025/
KX-MB2030 only)
–
Device Monitor
84
10. Help
Problem
Cause & Solution
I forgot the password for
feature programming via
remote operation.
R You may have changed the feature programming password. If you do not
remember it, assign a new password using feature #155 (page 59). When
required to enter the current password, enter “0101” instead.
10.3.2 Printing problems
Problem
Cause & Solution
The printing quality is poor
(e.g. has smudges, blurred
points or lines).
R Some paper has instructions recommending which side to print on. Try
turning the recording paper over.
R You may have used paper with a cotton and/or fibre content that is over
20 %, such as letterhead or resume paper.
R The recording paper is too damp. Use new paper.
ABC
I changed the recording
paper, but the printing quality
is still poor.
R The glass or rollers are dirty with correction fluid, etc. Clean them
has dried completely.
R The remaining toner is low. Replace the toner cartridge.
R To check the drum life and quality, please print the printer test list
drum cartridge.
A blank sheet is ejected.
R You placed the document facing the wrong way when using the copier.
R The other party placed the document in their fax machine the wrong way.
Check with the other party (KX-MB2025/KX-MB2030 only).
Coloured and grey objects
are printed in black instead of
greyscale when printing from
Microsoft PowerPoint or
other applications.
R Select [Color] or remove the check next to [Grayscale] in the print dialogue
so that coloured or grey objects will be printed in greyscale properly.
When using the unit as a
printer, the printing result is
distorted.
R Your unit is connected to the computer by USB. After cancelling printing
using your computer, you must wait for 60 seconds before re-printing to
avoid distorted printing.
10.3.3 Scanner
Problem
Cause & Solution
I cannot scan.
R When scanning at a high resolution, a large amount of available memory is
required. If your computer warns that there is insufficient memory, close
other applications and try again.
R The unit is in use. Try again later.
R There is not enough space on the hard disk. Delete unnecessary files and
try again.
R Restart the computer, and try again.
R You attempted to scan a document longer than the paper size which you
set. Change the setting or divide the document into the appropriate paper
size, and try again.
85
10. Help
Problem
Cause & Solution
The document is not fed into
the unit when using the unit
as a scanner (KX-MB2010/
KX-MB2025/KX-MB2030
only).
R Remove the document in the automatic document feeder and re-insert it.
Even after clicking [Cancel],
scanning continues.
R Please wait. It may take a while for the cancel request to be accepted.
The name of the desired
computer is not displayed on
the unit when scanning
documents from the unit
(KX-MB2000/KX-MB2010/
KX-MB2030, LAN connection
only).
R The printer driver has not been installed. Install it on your computer
R The PC name list up feature has been set to [Off]. Set [PC name list up
R The maximum number of computers on the LAN is connected to the unit (up
to 30 computers). Set [PC name list up on device] to [Off] on the other
R The IP address of the unit may have changed. To detect the IP address,
proceed as follows.
[Start] A [All Programs] or [Programs] A [Panasonic] A the unit’s
name A [IP Address Checker]
R The IP address for the unit will be detected.
10.3.4 Copier
Problem
Cause & Solution
The unit will not make a copy. R You cannot make a copy during programming. Make the copy after
programming.
R The document was not fed into the unit properly. Re-insert the document.
R Recording paper is not loaded or the unit has run out of paper. Load paper
Letters on the copied
R The original document is too dark or too light. Change the contrast
documents are not clear.
The copied documents are
too dark and cannot be read.
and make a lighter copy of the document, using “TEXT” resolution
10.3.5 Fax (KX-MB2025/KX-MB2030 only)
Problem
Cause & Solution
I cannot send documents.
R The telephone line cord is connected to the [EXT] jack on the unit. Connect
R The other party’s fax machine is busy or has run out of recording paper. Try
again.
R The other party’s machine is not a fax machine. Check with the other party.
R The other party’s fax machine failed to answer the fax automatically. Send
R Add two pauses at the end of the telephone number or dial manually.
The other party complains
that letters on their received
document are distorted.
R If your line has special telephone services such as call waiting, the service
may have been activated during fax transmission. Connect the unit to a line
that does not have these services.
R Another telephone on the same line is off the hook. Hang up the extension
telephone and try again.
86
10. Help
Problem
Cause & Solution
The other party complains
about the quality of their
received documents.
R Try copying the document. If the copied image is clear, there may be
something wrong with the other party’s machine.
If the copied image is not clear, too dark, or black and white lines or smudges
R The original document is too dark or too light. Change the contrast
The other party complains
that received documents are
too dark and cannot be read.
and make a lighter copy of the document, using “TEXT” resolution
I cannot receive documents.
R The telephone line cord is connected to the [EXT] jack on the unit. Connect
fax documents are automatically transferred to the computer. View the
received documents using the computer (page 53).
R If your unit is connected to the computer via the LAN and the fax preview
are automatically stored in memory. View the received documents on the
R Recording paper is installed in the manual input tray. Remove the recording
paper from the manual input tray.
I cannot receive documents
automatically.
R The time taken to answer the call is too long. Decrease the number of rings
before the unit answers a call (feature #210 on page 60).
The display shows
R The incoming call is not a fax. Change the receiving mode to TEL mode
“CONNECTING.....”, but
faxes are not received.
The printing quality of the
received documents is poor.
R If documents can be copied properly, the unit is working normally. The other
party may have sent a faint document or there may be something wrong
with the other party’s machine. Ask them to send a clearer copy of the
document or to check their fax machine.
The other party complains
that they cannot send a
document.
R The memory is full of received documents due to a lack of recording paper
or a recording paper jam. Load paper (page 14) or remove the jammed
the connection between the computer and the unit.
R If your unit is connected to the computer via the LAN and the fax preview
documents, and then erase unnecessary documents (page 53).
R The unit is not in FAX ONLY mode. Press MFax Auto AnswerN repeatedly
to turn ON the MFax Auto AnswerN light.
I cannot select the desired
receiving mode.
R If you want to set FAX ONLY mode:
–
press MFax Auto AnswerN repeatedly to turn ON the MFax Auto
AnswerN light.
R If you want to set TEL mode or TEL/FAX mode:
–
Auto AnswerN repeatedly to turn OFF the MFax Auto AnswerN light.
87
10. Help
Problem
Cause & Solution
is connected, I cannot receive
documents by pressing
MGNMBNM9N.
beforehand.
R Press MGNMBNM9N firmly.
R You may have changed the remote fax activation code from MGNMBNM9N
(default setting). Verify the remote fax activation code (feature #434 on
I cannot hear a dial tone.
R The telephone line cord is connected to the [EXT] jack on the unit. Connect
R If you use a splitter/coupler to connect the unit, remove the splitter/coupler
and connect the unit to the wall jack directly. If the unit operates properly,
check the splitter/coupler.
R Disconnect the unit from the telephone line and connect a known working
telephone. If the working telephone operates properly, contact our service
personnel to have the unit repaired. If the working telephone does not
operate properly, contact your telephone company.
R The power cord or telephone line cord is not connected. Check the
R If you connected the unit through a computer modem, connect the unit
directly to a telephone line jack.
I cannot make calls.
R The dialling mode setting may be wrong. Change the setting (feature #120
The unit does not ring.
The other party complains
they only hear a fax tone and
cannot talk.
used for faxes.
The MRedialN or MPauseN
button does not function
properly.
R If this button is pressed during dialling, a pause will be inserted. If pressed
immediately after a dial tone is obtained, the last number dialled will be
redialled.
I cannot receive a fax
R Make sure the following features are set beforehand.
document on the computer.
–
–
PC fax reception (feature #442 on page 65)
Computer setting for the PC fax reception (feature #443 on page 24)
I cannot display a received fax R Make sure the following features are set beforehand.
document on the web
browser (KX-MB2030 only).
–
–
Fax preview mode (feature #448 on page 53)
Web fax preview access code (feature #450 on page 53)
R You cannot display a received fax document on the web browser during
printing, copying or scanning. Try again after printing, copying or scanning.
I cannot erase a received fax
document on the web
browser (KX-MB2030 only).
88
10. Help
10.3.6 Network (KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only)
Problem
Cause & Solution
I cannot operate the following R Confirm the LED via the LAN port of the main board. If the LED is glowing
functions.
or blinking, network access is working correctly.
–
–
–
–
–
PC printing
Scanning
Remote Control
PC FAX (KX-MB2030 only)
Device Monitor
If the LED is not glowing or blinking, confirm the LAN cable (category 5
straight cable) is connected to the LAN port of the main board correctly.
R If the LED is blinking and you cannot perform the desired operation, the IP
address of the unit may have changed.
To detect the IP address, proceed as follows.
[Start] A [All Programs] or [Programs] A [Panasonic] A the unit’s
name A [IP Address Checker]
R The IP address for the unit will be detected.
Note:
R If the IP address cannot be detected, enter it manually (feature #501 on
same local IP address class as shown below. Set the IP address in the
range of the number specified in the class corresponding to your local
network scale.
Class
Subnet mask
IP address
Class A
255.0.0.0
10.0.0.1 -
10.255.255.254
Class B
Class C
255.255.0.0
172.xx.0.1 -
172.xx.255.254
255.255.255.0
192.168.xx.1 -
192.168.xx.254
*1 “xx” should be the same value for the unit and for the computer,
as shown in the following example.
Example: 172.16.0.1 - 172.16.255.254
(The available range of “xx” is 16 - 31)
*2 “xx” should be the same value for the unit and for the computer,
as shown in the following example.
Example: 192.168.0.1 - 192.168.0.254
(The available range of “xx” is 0 - 255)
R Your firewall software is blocking the connection. Disable the firewall
software or change the firewall settings to make the Multi-Function Station
work properly.
R LAN features can be used when the unit and the computer are connected
in same network segment only. Make sure the network is configured
correctly. Consult your network administrator.
The unit does not appear in
the [Select a Network Device]
dialogue box when installing
Multi-Function Station.
R Your firewall software is blocking the connection and the setup program may
not list any units. Consult your network administrator and temporarily disable
the firewall software.
R The unit is connected to another network segment and the setup program
may not list any units. Make sure the network is configured correctly. Consult
your network administrator.
89
10. Help
Problem
Cause & Solution
The [Windows Security Alert] R Click [Keep Blocking] and run the Windows Firewall Setting Tool to allow
dialogue box appears and
asks if I want to block
the data transmission for Multi-Function Station (page 90).
[PCCMFLPD] and I cannot
operate the following
functions after installing the
Microsoft Windows XP
Service Pack 2 or later.
–
–
–
–
–
PC printing
Scanning
Remote Control
PC FAX (KX-MB2030 only)
Device Monitor
10.3.7 Using an answering machine (KX-MB2025/KX-MB2030 only)
Problem
Cause & Solution
I cannot receive documents
automatically.
R Your greeting message on the answering machine is too long. Shorten the
message. Record a message less than 10 seconds long.
R The answering machine rings too many times. Set to 1 or 2 rings.
I cannot receive voice
messages.
R Check if the answering machine is turned ON and connected to the unit
R Set the number of rings on the answering machine to 1 or 2.
I pressed the remote access
code to access the answering
machine remotely, but the line
was disconnected.
R The code may include “#” which is used for certain features provided by
telephone companies. Change the code on the answering machine to
another number which does not include “#”.
Callers complain that they
cannot send a document.
R There is no room left in the memory of your answering machine to record
voice messages. See the operating instructions of the answering machine
and erase unnecessary messages.
R You set the answering machine to only give a greeting message.
10.3.8 If a power failure occurs
R The unit will not function.
R If any documents are stored in the memory (i.e. during copying, PC printing), they will be lost.
KX-MB2025/KX-MB2030 only:
R The unit is not designed for making emergency telephone calls when the power fails. Alternative arrangements
should be made for access to emergency services.
R Fax transmission and reception will be interrupted.
R Documents during fax transmission or fax reception will be lost.
R When power is restored, a power down report will be printed out stating which fax items in the memory have been
erased.
10.3.9 Firewall setting tool for Microsoft Windows XP Service Pack 2 or later/Windows Vista
users (KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only)
After installing Microsoft Windows XP Service Pack 2 or later/Windows Vista, you will not be able to use the following
functions because the Windows Firewall feature will be activated and block the connection.
–
–
Device Monitor
LPD Manager (Network communication tool)
The Windows Firewall Setting Tool enables you to change the Windows Firewall security settings and to use the
above functions properly.
90
10. Help
1 Insert the CD-ROM that is supplied with the unit into your CD-ROM drive.
R If the [Select Language] dialogue box appears, select the desired language that you want to use with this
software. Click [OK].
2 [Tools] A [Windows Firewall Setting]
R The [Windows Firewall Setting Tool] window will appear.
3 [Add to the exceptions list] A [OK] A [OK]
To confirm the security settings (For Windows XP users)
1. [Start] A [Control Panel] A [Security Center]
R The [Windows Security Center] window will appear.
2. [Windows Firewall]
R The [Windows Firewall] dialogue box will appear.
3. Click the [Exceptions] tab.
4. Confirm that [Panasonic Trap Monitor Service] and [Panasonic LPD] are displayed and checked on the
[Programs and Services] list.
To confirm the security settings (For Windows Vista users)
1. [Start] A [Control Panel] A [Security Center]
R The [Windows Security Center] window will appear.
2. [Windows Firewall]
R The [Windows Firewall] dialogue box will appear.
3. [Change settings]
R The [User Account Control] dialogue box will appear.
4. [Continue]
5. Click the [Exceptions] tab.
6. Confirm that [Panasonic Trap Monitor Service], [Panasonic LPD Manager] and [Panasonic LPD] are
displayed and checked on the [Program or port] list.
10.3.10 Notice for KX-MB200/KX-MB700/KX-FLB880 series users
If you have already installed KX-MB200/KX-MB700/KX-FLB880 series Multi-Function Station on your computer, use
the following instructions to modify or add the printer driver, which changes after installing the KX-MB2000 series
Multi-Function Station.
You can modify or add a printer driver, as follows:
1 Start Windows and insert the KX-MB200/KX-MB700/KX-FLB880 series CD-ROM into your CD-ROM drive.
R If the [Select Language] dialogue box appears, select the desired language that you want to use with this
software. Click [OK].
2 [Easy installation]
3 [Modify] A [Next]
4 Select [Modify Utility] or [Add Printer Driver]. A [Next]. Then follow the on-screen instructions.
Important:
R For users of versions prior to 1.12, download the latest software as follows, then activate it.
[Start] A [All Programs] or [Programs] A [Panasonic] A the unit’s name A [Support Web Page].
Then follow the on-screen instructions.
91
11. Paper Jams
Case 1:
11.1 Recording paper jam
Caution:
When the recording paper has jammed near the
manual input tray:
11. . Paper Jams
1. Pull open the paper input tray (A).
R Do not pull out the jammed paper forcibly before
opening the top cover.
A
R To prevent injuries, be careful not to put your
hands under the top cover.
2. Open the manual input tray (B) and remove the
jammed paper (C) carefully by pulling it upwards.
Then close the manual input tray.
C
B
3. Close the paper input tray.
11.1.1 When the recording paper has jammed
inside of the unit
D
The display will show the following:
–
“PAPER JAMMED”
L
“OPEN TOP COVER”
–
“CHECK REAR COVER”
92
11. Paper Jams
R Open and close the top cover (D) to clear the
Case 2:
message.
When the recording paper has jammed near the
drum and toner cartridge:
1. Pull open the paper input tray (A).
A
2. Open the top cover (B) by holding the indentations
(C) on both sides of the unit.
E
B
C
D
C
Caution:
R The fuser unit (D) gets hot. Do
not touch it.
Note:
R Do not touch the transfer roller (E).
93
11. Paper Jams
3. Remove the jammed paper (F) carefully by pulling it
4. Close the paper input tray.
upwards.
F
5. Close the top cover by holding the indentations on
Remove the jammed paper (G) carefully by pulling it
toward you.
both sides of the unit, until locked.
G
94
11. Paper Jams
Case 3:
3. Remove the jammed paper (F) carefully by pulling it
upwards.
When the recording paper has jammed near the fuser
unit:
1. Open the top cover (A) by holding the indentations
(B) on both sides of the unit.
D
A
B
C
F
B
4. Push back the green levers (G) to the original
position.
Caution:
R The fuser unit (C) gets hot. Do
not touch it.
Note:
R Do not touch the transfer roller (D).
2. Lift both green levers (E) until they stop.
G
E
95
11. Paper Jams
5. Close the top cover by holding the indentations on
11.1.2 When the recording paper is not fed
into the unit properly
both sides of the unit, until locked.
The display will show the following:
–
“CHECK PAPER #1 PRESS START”
1 Pull the paper input tray until it clicks into place, then
pull it completely out, lifting the front part of the tray.
Remove the recording paper and straighten.
2 Re-load the recording paper.
3 Insert the paper input tray into the unit, lifting the front
part of the tray. Then push it completely into the unit.
Note:
R If the message is still displayed, check the recording
paper specifications and load the recording paper
11.1.3 When the recording paper in the
manual input tray is not fed into the unit
properly
The display will show the following.
–
“CHECK PICK UP INPUT TRAY #2”
1 Remove the recording paper.
2 Re-insert the recording paper.
96
11. Paper Jams
Note:
11.2 Document jams (Automatic
document feeder) (KX-MB2010/
KX-MB2025/KX-MB2030 only)
R If the message is still displayed, check the recording
paper specifications and re-install recording paper.
Note:
R The pictured model is KX-MB2010.
Caution:
R Do not pull out the jammed document forcibly
before lifting the ADF cover.
1 Open the ADF cover (A) while holding the document
cover (B).
A
B
97
11. Paper Jams
2 Remove the jammed document (C) carefully.
When the document has jammed near the
document entrance:
C
When the document has jammed near the
document exit:
C
3 Close the ADF cover.
98
12. Cleaning
2 Hold the document cover while cleaning the white
12.1 Cleaning the white plates and
glass
plates (B) and the scanner glass (C).
12. . Cleaning
Clean the white plates and glass when a black line, a
white line or a dirty pattern appears on:
B
C
–
–
–
–
your recording paper,
the original document,
the scanned data, or
the fax document received by the other party
(KX-MB2025/KX-MB2030 only).
Caution:
R Be careful when handling the drum and toner
cartridge. See the caution for the drum cartridge
R Do not use paper products, such as paper towels
or tissues for cleaning.
12.1.1 White plates and scanner glass
1 Open the document cover (A).
3 Close the document cover.
A
99
12. Cleaning
3 Remove the drum and toner cartridge (E) by holding
12.1.2 Lower glass
the tabs.
1 Turn the power switch OFF.
2 Open the top cover (A) by holding the indentations
(B) on both sides of the unit.
D
A
B
E
C
B
4 Clean the lower glass (F) with a soft and dry cloth.
Caution:
The fuser unit (C) gets hot. Do not
touch it.
Note:
F
R Do not touch the transfer roller (D).
100
12. Cleaning
5 Reinstall the drum and toner cartridge (G) by holding
6 Close the top cover by holding the indentations on
the tabs.
both sides of the unit, until locked.
G
Caution:
R Make sure that the arrows (H) match, to install
the drum and toner cartridge correctly.
R To prevent injuries, be careful not to put your
hands under the top cover.
H
7 Turn the power switch ON.
101
12. Cleaning
3 Clean the document feeder rollers (C) with a cloth
12.2 Cleaning the document
feeder rollers (KX-MB2010/
KX-MB2025/KX-MB2030 only)
Clean the rollers when documents frequently misfeed.
moistened with water, and let all parts dry thoroughly.
Note:
R The pictured model is KX-MB2010.
Caution:
R Do not use paper products, such as paper towels
C
or tissues for cleaning.
1 Turn the power switch OFF.
2 Open the ADF cover (A) while holding the document
cover (B).
A
B
4 Close the ADF cover.
5 Turn the power switch ON.
102
13. General Information
13.1 Reference lists and reports
13.2 Specifications
You can print out the following lists and reports for your
reference.
13.
.
General Information
n Applicable lines :
Public Switched Telephone Network
–
–
–
“SETUP LIST”
n Document size:
“TEL NO. LIST”
Max. 216 mm in width, Max. 600 mm in length
“JOURNAL REPORT”
n Effective scanning width:
–
–
“BROADCAST LIST”
208 mm
“PRINTER TEST”
n Effective printing width:
Letter/Legal: 208 mm
A4: 202 mm
–
–
–
–
“CALLER ID LIST”
“ADDRESS LIST”
n Transmission time
Approx. 4 s/page (ECM-MMR Memory
:
“FTP SERVER LIST”
“SMB FOLDER LIST”
transmission)
*1 KX-MB2025/KX-MB2030 only
*2 KX-MB2000/KX-MB2010/KX-MB2030 only
n Scanning density:
Scanning resolution:
Up to 600 ´ 1,200 dpi (Optical)
Up to 9,600 ´ 9,600 dpi (Interpolated)
MMenuN
Copy resolution:
Up to 600 ´ 600 dpi
Fax resolution :
Horizontal: 8 pels/mm
Vertical: 3.85 lines/mm -in standard resolution,
7.7 lines/mm -in fine/photo resolution,
MSetN MFNMEN
15.4 lines/mm -in super fine resolution
n Photo resolution:
64-level
1 Press MMenuN repeatedly to display “PRINT
REPORT”.
n Scanner type:
Colour Contact Image Sensor
2 Press MFN or MEN repeatedly to display the desired
item.
n Printer type:
Laser Printer
3 Press MSetN to start printing. A MMenuN
n Data compression system :
Modified Huffman (MH), Modified READ (MR),
Modified Modified READ (MMR)
n Modem speed :
33,600 / 31,200 / 28,800 / 26,400 / 24,000 / 21,600 /
19,200 / 16,800 / 14,400 / 12,000 / 9,600 / 7,200 /
4,800 / 2,400 bps; Automatic Fallback
n Operating environment:
10 °C – 32.5 °C, 20 % – 70 % RH (Relative Humidity)
n Dimensions:
KX-MB2000: Approx. width 420 mm ´ depth 432 mm
´ height 255 mm
KX-MB2010/KX-MB2025/KX-MB2030: Approx. width
420 mm ´ depth 432 mm ´ height 305 mm
n Mass (Weight):
KX-MB2000: Approx. 11 kg
KX-MB2010/KX-MB2025/KX-MB2030: Approx. 12 kg
103
13. General Information
ITU-T No.1 Test Chart
n Power consumption:
Standby: Approx. 5.5 W
Preheat: Approx. 65 W
Copy: Approx. 500 W
Maximum: Approx. 1,000 W (When the fuser lamp
turns on)
n Power supply:
220–240 V AC, 50/60 Hz
n Memory capacity
(for operation and storing memory):
32 MB
n Fax memory capacity :
3.5 MB in total
Approx. 110 pages of memory reception
Approx. 150 pages of memory transmission
(Based on the ITU-T No. 1 Test Chart in standard
resolution, without using the Error Correction Mode.)
Note:
R Design and specifications are subject to change
without notice.
R The pictures and illustrations in these instructions
may vary slightly from the actual product.
R The accuracy of the clock is approximately ±60
n Scan to email address memory capacity :
5 MB in total (including the header and email
message)
n Scan to FTP server memory capacity :
seconds a month.
5 MB in total
n Scan to SMB folder memory capacity :
5 MB in total
Recording paper specifications
Plain paper/Thin paper size:
n Laser diode properties:
Laser output: Max. 15 mW
Wavelength: 760 nm – 800 nm
Emission duration: Continuous
A4: 210 mm ´ 297 mm
Letter: 216 mm ´ 279 mm
Legal: 216 mm ´ 356 mm
B5(JIS): 182 mm ´ 257 mm
B5(ISO): 176 mm ´ 250 mm
16K: 195 mm ´ 270 mm
216 ´ 330: 216 mm ´ 330 mm
216 ´ 340: 216 mm ´ 340 mm
n Print speed:
Approx. 24 ppm (pages per minute)
n Printing resolution:
600 ´ 600 dpi
n LED light of CIS properties:
Label size:
LED radiation output: Max. 1 mW
A4: 210 mm ´ 297 mm
Letter: 216 mm ´ 279 mm
Wavelength: Red 630 nm typ.
Green 520 nm typ.
Blue 465 nm typ.
Recording paper weight:
Emission duration: Continuous
2
2
64 g/m to 90 g/m
*1 KX-MB2025/KX-MB2030 only
*1 Manual input tray only
*2 KX-MB2000/KX-MB2010/KX-MB2030 only
*3 Transmission speed depends on the contents of the
pages, resolution, telephone line conditions and
capability of the other party’s machine.
*4 Transmission speed is based on the ITU-T No. 1
Test Chart with original mode. If the capability of the
other party’s machine is inferior to your unit, the
transmission time may be longer.
104
13. General Information
pages your toner cartridge will print may be
Toner life
significantly less than this estimate if your unit is often
used for printing small number of pages per job.
Because many of the factors that determine the
actual toner cartridge life cannot be controlled, we
cannot guarantee a minimum number of pages that
will be printed by your toner cartridge.
Toner cartridge life depends on the amount of content in
a printed document. Toner cartridge life varies in actual
usage. The following is the approximate number of
pages that the toner cartridge can print according to the
various printing examples.
Example 1
R The number of pages changes with the depth,
thickness and size of the characters.
R If you turn on the toner save feature, the toner
Approx. 2,000 pages can be printed.
cartridge will last approx. 20 % longer.
Table of Contents1.
1. Table of Contents 1. Introduction and Installation Accessories
1.1 Included accessories.1.2 Accessory information.Finding the Controls
1.3 Description of buttons.1.4 Overview Installation
1.5 Toner cartridge and drum unit
1.6 Document tray 1.7 Output tray1.8 Recording paper2. Preparation
2.1 Connections 2.2 Turning the power switch ON Help Button2.3 Help function Volume
Drum life
The drum cartridge needs to be replaced regularly. The
maximum drum life is approx. 6,000 pages.
4. PC Operations/ Setup 4.1 Connecting to
4.2 Installing Multi-Function Station 4.3 Starting Multi-Function Station Printing
4.4 Using the unit as printer Scanning 4.5 Using the unit as scannerRemote Control
a
computer
a
a
4.6 Operating the unit from your computer.
4.7 Fax sending/receiving using Multi-Function Station
4.8 Registering the computer in the LANnetwork with the optional LAN board
4.9 Confirming the status of the unit 5. Case Setup
/
5.1 Selecting the way to use your unit 5.2 Case 1: FAX ONLY
Note:
Table of Contents2.
R There are various factors that determine the actual
drum cartridge life, such as temperature, humidity,
type of paper and how much toner you use for the
number of pages per print job. The actual number of
pages your drum cartridge will print may be
1. Table of Contents
1.1 Included accessories.1.2 Accessory information.Finding the Controls
1.3 Description of buttons.1.4 Overview Installation1.5 Toner cartridge and drum unit
1.6 Document tray 1.7 Output tray1.8 Recording paper2. Preparation
2.1 Connections 2.2 Turning the power switch ON Help Button2.3 Help function Volume
Thank you for purchasing
Things you should keep
a
Panasonic fax machine.
a
record of
Attach your sales receipt here.
For your future reference
Date of purchase
significantly less than this estimate if your unit is often
used for printing small number of pages per job.
Because many of the factors that determine the
actual drum cartridge life cannot be controlled, we
cannot guarantee a minimum number of pages that
will be printed by your drum cartridge.
Example 2
Approx. 1,000 pages can be printed.
Table of Contents1.
1. Table of Contents
/
Introduction and Installation Accessories
1.1 Included accessories.
1.2 Accessory information.Finding the Controls
1.3 Description of buttons.
1.4 Overview Installation
1.5 Toner cartridge and drum unit
1.6 Document tray
Waste disposal method
1.7 Output tray
1.8 Recording paper
2. Preparation
2.1 Connections
2.2 Turning the power switch ON Help Button
2.3 Help function Volume
2.4 Adjusting volume Initial Programming
Waste material should be disposed of under conditions
which meet all national and local environmental
regulations.
2.5 Dialing mode
2.7 Your logo.
2.6 Date and time.
2.8 Your fax number
Thank you for purchasing
a
Panasonic fax machine.
Things you should keep
a
record of
Attach your sales receipt here.
For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Example 3
Approx. 650 pages can be printed.
Table of Contents1.
1. Table of Contents
/
Introduction and Installation Accessories
1.1 Included accessories.
1.2 Accessory information.Finding the Controls
1.3 Description of buttons.
1.4 Overview Installation
1.5 Toner cartridge and drum unit
1.6 Document tray
1.7 Output tray
2. Preparation
2.1 Connections
1.8 Recording paper
Thank you for purchasing
a
Panasonic fax machine.
Things you should keep
a
record of
Attach your sales receipt here.
For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Note:
R There are various factors that determine the actual
toner cartridge life, such as temperature, humidity,
type of paper and how much toner you use for the
number of pages per print job. The actual number of
105
13. General Information
13.3 Information of copyrights and licences (KX-MB2000/KX-MB2010/
KX-MB2030 only)
R This product uses a part of NetBSD kernel.
The use of a part of NetBSD kernel is based on the typical BSD style licence below.
Copyright (c)
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted
provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and
the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions
and the following disclaimer in the documentation and/or other materials provided with the
distribution.
3. All advertising materials mentioning features or use of this software must display the following
acknowledgement:
This product includes software developed by the University of California, Berkeley and its
contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or
promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
However, parts of the NetBSD Kernel are provided with the following copyright notices.
Copyright (c) 1980, 1983, 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1985, 1986, 1988, 1993, 1994 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993, 1994, 1995 The Regents of the University of California. All
rights reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993, 1995 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1988, 1991, 1993 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1988, 1993, 1995 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1989, 1993 The Regents of the University of California. All rights reserved.
106
13. General Information
Copyright (c) 1982, 1986, 1990, 1991, 1993 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1990, 1993, 1994 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1991, 1993, 1994 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1991, 1993, 1995 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1993, 1994, 1995 The Regents of the University of California. All rights
reserved.
Copyright (c) 1982, 1986, 1993, 1995 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1988, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1983, 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1983, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1985, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1985, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988 Regents of the University of California. All rights reserved
Copyright (c) 1988 Stephen Deering.
Copyright (c) 1988 University of Utah.
Copyright (c) 1988, 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1990, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1991, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1992 Regents of the University of California. All rights reserved.
Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1993 Adam Glass
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Copyright (c) 1994 Gordon W. Ross
Copyright (c) 1994 Winning Strategies, Inc. All rights reserved.
Copyright (c) 1995 The Regents of the University of California. All rights reserved.
Copyright (C) 1995, 1996, 1997, and 1998 WIDE Project. All rights reserved.
Copyright (c) 1996 The Regents of the University of California. All rights reserved.
Copyright (c) 1996 John S. Dyson All rights reserved.
Copyright (c) 1996 Matt Thomas. All rights reserved.
Copyright (c) 1996 Matthew R. Green. All rights reserved.
Copyright (c) 1996 Paul Kranenburg
Copyright (c) 1996, 1997, 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1996, 2000 Christopher G. Demetriou. All rights reserved.
107
13. General Information
Copyright (c) 1996,1999 by Internet Software Consortium.
Copyright (c) 1996-1999 by Internet Software Consortium.
Copyright (c) 1997 Jonathan Stone and Jason R. Thorpe. All rights reserved.
Copyright (c) 1997 Christos Zoulas. All rights reserved.
Copyright (c) 1997 Manuel Bouyer. All rights reserved.
Copyright (c) 1997, 1998 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997,98 The NetBSD Foundation, Inc. All rights reserved.
Copyright (C) 1997-2000 Sony Computer Science Laboratories Inc. All rights reserved.
Copyright (c) 1997-2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998 Todd C. Miller <Todd.Miller@courtesan.com> All rights reserved.
Copyright (c) 1998, 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 1999, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (C) 1999 WIDE Project. All rights reserved.
Copyright (c) 1999, 2000 Jason L. Wright (jason@thought.net) All rights reserved.
Copyright (c) 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000, 2001, 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright 1998 Massachusetts Institute of Technology. All rights reserved.
Copyright 2001 Wasabi Systems, Inc. All rights reserved.
Portions Copyright (c) 1993 by Digital Equipment Corporation.
Portions Copyright (c) 1995 by International Business Machines, Inc.
Copyright (c) 1983, 1989 The Regents of the University of California. All rights reserved.
Copyright (c) 1996 by Internet Software Consortium. All rights reserved.
Copyright (c) 1980, 1986, 1989 Regents of the University of California. All rights reserved.
Copyright (c) 1988 The Regents of the University of California. All rights reserved.
Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1994 Christopher G. Demetriou. All rights reserved.
Copyright (c) 1997 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1996 Gardner Buchanan <gbuchanan@shl.com> All rights reserved.
Parts of the NetBSD Kernel are provided with the licences that are slightly different from the above Berkeley-formed
licence. Please refer the source code of the NetBSD Kernel about the details.
The source code of the NetBSD Kernel is provided by the NetBSD CVS Repositories
(http://cvsweb.netbsd.org/bsdweb.cgi/), and this product includes parts of the source code in the following directories.
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/kern/
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/net/
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/netinet/
108
13. General Information
R This product contains Net-SNMP software and is using it based on the following licence conditions.
---- Part 1: CMU/UCD copyright notice: (BSD like) -----
Copyright 1989, 1991, 1992 by Carnegie Mellon University
Derivative Work - 1996, 1998-2000
Copyright 1996, 1998-2000 The Regents of the University of California
All Rights Reserved
Permission to use, copy, modify and distribute this software and its documentation for any purpose and
without fee is hereby granted, provided that the above copyright notice appears in all copies and that
both that copyright notice and this permission notice appear in supporting documentation, and that the
name of CMU and The Regents of the University of California not be used in advertising or publicity
pertaining to distribution of the software without specific written permission.
CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA DISCLAIM ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE
UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL
DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
SOFTWARE.
---- Part 2: Networks Associates Technology, Inc copyright notice (BSD) -----
Copyright (c) 2001-2003, Networks Associates Technology, Inc
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
*
*
*
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
Neither the name of the Networks Associates Technology, Inc nor the names of its contributors may
be used to endorse or promote products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS''
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
109
13. General Information
---- Part 3: Cambridge Broadband Ltd. copyright notice (BSD) -----
Portions of this code are copyright (c) 2001-2003, Cambridge Broadband Ltd.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
*
*
*
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
The name of Cambridge Broadband Ltd. may not be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER ``AS IS'' AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
---- Part 4: Sun Microsystems, Inc. copyright notice (BSD) -----
Copyright © 2003 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara,
California 95054, U.S.A. All rights reserved.
Use is subject to licence terms below.
This distribution may include materials developed by third parties.
Sun, Sun Microsystems, the Sun logo and Solaris are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
*
*
*
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
Neither the name of the Sun Microsystems, Inc. nor the names of its contributors may be used to
endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS''
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE
110
13. General Information
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Also this product contains software which includes following notices and licences.
/***********************************************************
Copyright 1988, 1989, 1990 by Carnegie Mellon University
Copyright 1989 TGV, Incorporated
All Rights Reserved
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and
without fee is hereby granted, provided that the above copyright notice appear in all copies and that
both that copyright notice and this permission notice appear in supporting documentation, and that the
name of CMU and TGV not be used in advertising or publicity pertaining to distribution of the software
without specific, written prior permission.
CMU AND TGV DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CMU OR
TGV BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY
DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR
IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
******************************************************************/
R This product contains NetBSD software and is using it based on the following licence conditions.
/*-
* Copyright (c) 1990 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Chris Torek.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
*
following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors may be used to endorse or
*
*
*
promote products derived from this software without specific prior written permission.
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
111
13. General Information
R This product contains NetBSD software and is using it based on the following licence conditions.
/*
* Copyright (c) 1989 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Tom Truscott.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
*
following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software must display the following
*
*
*
*
acknowledgement:
This product includes software developed by the University of California, Berkeley and its
contributors.
* 4. Neither the name of the University nor the names of its contributors may be used to endorse or
*
*
promote products derived from this software without specific prior written permission.
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
R This product contains NetBSD software and is using it based on the following licence conditions.
/*
* Copyright (c) 1987, 1993, 1994
* The Regents of the University of California. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
*
following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software must display the following
*
*
*
*
acknowledgement:
This product includes software developed by the University of California, Berkeley and its
contributors.
* 4. Neither the name of the University nor the names of its contributors may be used to endorse or
*
*
promote products derived from this software without specific prior written permission.
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
112
13. General Information
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
*
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*
*/
R This product contains NetBSD software and is using it based on the following licence conditions.
/*-
* Copyright (c) 1990, 1993
* The Regents of the University of California. All rights reserved.
*
* This code is derived from software contributed to Berkeley by Chris Torek.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
*
following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors may be used to endorse or
*
*
*
promote products derived from this software without specific prior written permission.
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
R This product contains thttpd software that ACMELabs developed and is using it based on the following licence
conditions.
Copyright 1995,1998,1999, 2000 by Jef Poskanzer <jef@acme.com>.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
113
13. General Information
R This product contains NetBSD software and is using it based on the following licence conditions.
/*-
* Copyright (c) 1990 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Chris Torek.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
*
following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors may be used to endorse or
*
*
*
promote products derived from this software without specific prior written permission.
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
R This product contains NetBSD software and is using it based on the following licence conditions.
/*-
* Copyright (c) 1990 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Chris Torek.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
*
following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors may be used to endorse or
*
*
*
promote products derived from this software without specific prior written permission.
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
114
13. General Information
R This product contains NetBSD software and is using it based on the following licence conditions.
/*
* Copyright (c) 1989 The Regents of the University of California.
* All rights reserved.
*
* This code is derived from software contributed to Berkeley by Tom Truscott.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided
* that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
*
following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software must display the following
*
*
*
*
acknowledgement:
This product includes software developed by the University of California, Berkeley and its
contributors.
* 4. Neither the name of the University nor the names of its contributors may be used to endorse or
* promote products derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
R This product includes only MD4 and DES of OpenSSL software developed by the OpenSSL Project, which are
used only in SMB protocol authentication. Also OpenSSL software is used under the following terms and conditions
of licence.
LICENCE ISSUES
==============
The OpenSSL toolkit stays under a dual licence, i.e. both the conditions of
the OpenSSL Licence and the original SSLeay licence apply to the toolkit.
See below for the actual licence texts. Actually both licences are BSD-style
Open Source licences. In case of any licence issues related to OpenSSL
please contact openssl-core@openssl.org.
OpenSSL Licence
---------------
/* ====================================================================
* Copyright (c) 1998-2000 The OpenSSL Project. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
115
13. General Information
* 1. Redistributions of source code must retain the above copyright
*
*
notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
*
*
*
*
notice, this list of conditions and the following disclaimer in
the documentation and/or other materials provided with the
distribution.
* 3. All advertising materials mentioning features or use of this
*
*
*
*
software must display the following acknowledgment:
"This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit. (http://www.openssl.org/)"
* 4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to
*
*
*
*
endorse or promote products derived from this software without
prior written permission. For written permission, please contact
openssl-core@openssl.org.
* 5. Products derived from this software may not be called "OpenSSL"
*
*
*
nor may "OpenSSL" appear in their names without prior written
permission of the OpenSSL Project.
* 6. Redistributions of any form whatsoever must retain the following
*
*
*
*
acknowledgment:
"This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit (http://www.openssl.org/)"
* THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY
* EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR
* ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
* OF THE POSSIBILITY OF SUCH DAMAGE.
* ====================================================================
*
* This product includes cryptographic software written by Eric Young
* (eay@cryptsoft.com). This product includes software written by Tim
* Hudson (tjh@cryptsoft.com).
*
*/
Original SSLeay Licence
-----------------------
/* Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
* All rights reserved.
*
* This package is an SSL implementation written
* by Eric Young (eay@cryptsoft.com).
* The implementation was written so as to conform with Netscapes SSL.
*
116
13. General Information
* This library is free for commercial and non-commercial use as long as
* the following conditions are aheared to. The following conditions
* apply to all code found in this distribution, be it the RC4, RSA,
* lhash, DES, etc., code; not just the SSL code. The SSL documentation
* included with this distribution is covered by the same copyright terms
* except that the holder is Tim Hudson (tjh@cryptsoft.com).
*
* Copyright remains Eric Young's, and as such any Copyright notices in
* the code are not to be removed.
* If this package is used in a product, Eric Young should be given attribution
* as the author of the parts of the library used.
* This can be in the form of a textual message at program startup or
* in documentation (online or textual) provided with the package.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
*
*
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
*
*
*
*
*
must display the following acknowledgement:
"This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com)"
The word 'cryptographic' can be left out if the rouines from the library
being used are not cryptographic related :-).
* 4. If you include any Windows specific code (or a derivative thereof) from
*
*
*
the apps directory (application code) you must include an acknowledgement:
"This product includes software written by Tim Hudson (tjh@cryptsoft.com)"
* THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* The licence and distribution terms for any publically available version or
* derivative of this code cannot be changed. i.e. this code cannot simply be
* copied and put under another distribution licence
* [including the GNU Public Licence.]
*/
R JPEG
This software is based in part on the work of the Independent JPEG Group.
117
14. Index
D
J
Jams
Document: 97
L
Label: 29
M
Multi-Function Station software
Activating: 27
E
Email address
Storing: 70
F
Installing: 25
Uninstalling: 26
N
O
One-touch dial
H
Help: 21
P
Paper size
Paper type
Phonebook
Storing: 43
Polling: 51
Copier: 21
Phonebook: 21
Reports: 21
I
Input tray setting
119
Notes
121
Notes
122
Notes
123
PNQX2616ZA CM1209SY0
|
Ram Mounting Systems Rpr 182 Co5 Ins User Manual
Samsung Aw06fasaa User Manual
Sanyo N 220aaas User Manual
Sanyo Ths4232 User Manual
Schumacher Elite Se 1555a User Manual
Snapper 1694923 User Manual
Uniden Xsa 975 User Manual
Wtb Vanilla 125r User Manual
Xantrex Technology Dr1524e User Manual
Xerox 432 User Manual