Operating Instructions
& Parts Manual
Hydraulic
Transmission Jacks
Model Number
41100
Capacity
1100 Lbs
2000 Lbs
3000 Lbs
42000
43000
Model 42000
Model 43000
Model 41100
Shinn Fu Co. of America, Inc. ©2002
10939 N. Pomona Avenue
Kansas City, MO 64153
OIPM#41100-TJ2
Printed in Taiwan
MAINTENANCE
!
WARNING
Important: Use only a good grade hydraulic jack oil.
Avoid mixing different types of fluid and NEVER use
brake fluid, turbine oil, transmission fluid, motor oil or
glycerin. Improper fluid can cause premature failure
of the jack and the potential for sudden and immediate
loss of load.
Study, understand, and follow all printed materials
provided with/on this device before use. Do not
exceed rated capacity. Use only on hard, level,
seamless surface. Use of this jack is limited to the
removal, installation and transportation of
transmissions, transfer cases and transaxles.
Adequately support the vehicle before starting repairs.
Failure to heed these markings may result in personal
injury and/or property damage.
Adding oil
1. With saddle fully lowered, set jack in its upright,
level position. Remove oil filler plug.
2. Fill until oil is level with the filler plug hole, reinstall
oil filler plug.
! Safety Messages !
Changing oil
Ensure the center of gravity is centered on the saddle.
Use only chains and slings provided. If loaded jack
must be moved, make certain that load is secured by
appropriate means, is stable, is in lowest possible
position. This is a lifting and lowering device only.
Transfer load immediately to appropriate support
device for service or repair. No alterations shall be
made to this product.
For best performance and longest life, replace the
complete fluid supply at least once per year.
1. With saddle fully lowered, set jack in its upright,
level position. Remove the oil filler plug.
2. Lay the jack on its side and drain the fluid into a
suitable container.
Note: Dispose of hydraulic fluid in accordance
with local regulations.
OPERATION
Raise saddle:
1. Locate and close release valve by turning knob
clockwise firmly, then pump the pump handle until
the load is contacted.
2. Follow vehicle manufacturers recommended proce-
dures for removing the load as outlined in vehicle
service manual or repair guide.
3. Secure load with provided restraints. Ensure load's
center of gravity is centered on the saddle and load
is stable before moving jack.
3. Set jack in its level upright position.
4. Fill with good quality jack oil. We recommend Mobil
DTE 13 or equivalent. Reinstall oil filler plug.
Lubrication
A periodic coating of light lubricating oil to pivot points,
axles and hinges will help to prevent rust and assure
that wheels, casters and pump assemblies move
freely.
Lower saddle:
Cleaning
1. Slowly, gently turn the release valve knob
counterclockwise, NEVER MORE THAN 1/2 FULL
TURN until the load is completely lowered.
2. Immediately transfer the load to an appropriate
repair fixture.
Periodically check the ram for signs of rust or
corrosion. Clean as needed and wipe with an oily
cloth.
Note: Never use sandpaper or abrasive material on
these surfaces!
Storage
! Caution !
When not in use, store the jack with pump piston and
saddle in lowest position.
Be sure all tools and personnel are clear before
lowering load. Dynamic shock loads are created by
quickly opening and closing the release valve as the
load is being lowered. The resulting overload may
cause hydraulic system failure.
OIPM#41100-TJ2
3
TROUBLESHOOTING
Symptom
Possible Causes
Corrective Action
• Ensure release valve tightly closed
• Remedy overload condition
• Ensure adequate air supply
• Release valve not tightly closed
• Overload condition
• Air supply inadequate
Jack will not lift load
• Release valve not tightly closed • Ensure release valve tightly closed
• Overload condition
• Hydraulic unit malfunction
• Remedy overload condition
• Contact Omega Tech. Service
Jack bleeds off after lift
• Reservoir overfilled
• Linkages binding
• Drain fluid to proper level
• Clean and lubricate moving parts
Jack will not lower after unloading
• Ensure proper fluid level
• Fluid level low
• With ram fully retracted, remove oil filler
plug to let pressurized air escape, then
reinstall oil filler plug
Poor lift performance
• Air trapped in system
• Fluid level low
Will not lift to full extension
• Ensure proper fluid level
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, Shinn Fu Co. of America, Inc. will repair or replace,
at its option, without charge, any of its products which fails due to a defect in material or workmanship, or which
fails to conform to any implied warranty not excluded hereby.
Performance of any obligation under this warranty may be obtained by returning the warranted product,
freight prepaid, to Shinn Fu Co. of America, Inc. Warranty Service Department, 10939 N. Pomona Ave., Kansas
City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law. (1) the
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS AS DESCRIBED ABOVE, and (2) Shinn Fu Co. of America, Inc. SHALL NOT BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE DURATION OF ANY AND
ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF ONE (1)
YEAR FROM DATE OF PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
REPLACEMENT PARTS
Available Parts: Please refer to the Parts drawings on pages 5, 6, and when ordering parts. Not all components of
the jack are replacement items, but are illustrated as a convenient reference of location and position in the
assembly sequence. When ordering parts, give Figure No. and the description. For example, to order an oil filler
plug for Model No. 41100, simply request Part # 41100-07, oil filler plug for Model No. 41100. Call or write for
current pricing: Shinn Fu Company of America, Inc. 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel:(888)332-6419 Fax:(816)891-6599 E-Mail:[email protected] Omega Website: http://www.omegalift.com
OIPM#41100-TJ2
4
Model 41100
Parts No.
Description
Quantity
1
2
3
4
5
6
7
8
power unit
oil filler plug
1
1
2
2
1
4
1
2
1
1
1
hyd. unit pivot pin
angle bracket assy.
chain
caster assembly
handle
adjusting knob
saddle
saddle support
label (not shown)
manual (OIPM# 41100-TJ2)
9
10
--
--
Figure 2 - Replacement Parts for Model 41100
OIPM#41100-TJ2
5
Model 42000
Parts No.
Description
Quantity
1
2
4
5
6
7
8
9
power unit
oil filler plug
angle bracket assy.
chain
caster assembly
handle
adjusting knob
saddle
saddle support
label (not shown)
manual (OIPM# 41100-TJ2)
1
1
2
1
4
1
2
1
1
1
1
10
--
--
8
10
5
4
9
2
1
7
6
Figure 3 - Replacement Parts for Model 42000
OIPM#41100-TJ2
6
Model 43000
Parts No.
Description
Quantity
1
2
3
4
5
6
7
--
--
power unit
1
1
1
4
1
2
2
1
1
oil filler screw
handle assembly
caster assembly
saddle assembly
adjusting knob
chain
label (not shown)
manual (OIPM# 41100-TJ2)
5
7
6
3
1
2
4
Figure 4 - Replacement Parts for Model 43000
OIPM#41100-TJ2
7
Notes
Shinn Fu Company of America, Inc.
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel:(888)332-6419 Fax:(816)891-6599 E-Mail:[email protected] Omega Website: http://www.omegalift.com
|