Operating Instructions
& Parts Manual
Hydraulic Toe Jacks
Model Number
13120
Capacity
6 Ton
13200
10 Ton
Shinn Fu Co. of America, Inc. ©2002
10939 N. Pomona Avenue
Kansas City, MO 64153
OIPM # 13120-TJ2
Printed in Taiwan
!
WARNING
WARNING
!
Study, understand, and follow all instructions before
operating this device. Do not exceed rated capacity.
Use only on hard, level surfaces. Lifting device only.
Immediately after lifting, support the vehicle with
appropriate means. Failure to heed these markings
may result in personal injury and/or property
damage.
OPERATION
Lifting
1. Assemble 3 pc. handle, ensure that spring clips
align with slots.
2. Secure the load to prevent inadvertent shifting and
movement.
3. Position the jack near desired lift point.
4. Close the release valve by turning it clockwise until
it is firmly closed.
To avoid crushing and related injuries:
NEVER work on, under or around a load supported
only by a jack. ALWAYS use adequately rated jack
stands.
OPERATION (continued)
Lowering
1. Raise load enough to carefully remove jack stands.
2. Insert handle onto release valve and slowly turn
handle counterclockwise, but no more than 1/2
turn.
Note: Use the handle provided with this product or an
authorized replacement handle to ensure proper
release valve operation. When using to lift vehicle, lift
only on the manufacturer’s recommended lift points
and in accordance with the published guidelines in
your vehicle owners manual. Always use jack stands
to support the load immediately after lifting.
3. If load fails to lower:
a. Carefully transfer the load to another lifting
device and jack stands.
b. Carefully remove affected jack, and then the
jack stands. Lower the load, again by slowly
turning the release valve no more than 1/2 turn.
5. Insert and secure handle into handle sleeve. Pump
handle until saddle contacts load.
6. Raise load to desired height, then immediately
transfer the load to appropriately rated support
devices such as jack stands.
! SAFETY MESSAGE !
Be sure all tools and personnel are clear before
lowering load. No alterations shall be made to this
device. Only attachments and/or adapters supplied
by the manufacturer shall be used.
4. After removing jack from under the load, push ram
and handle sleeve down to reduce exposure to rust
and contamination.
OIPM#13120-TJ2
3
MAINTENANCE
MAINTENANCE (continued)
Note: Dispose of hydraulic fluid in accordance with
local regulations.
Important: Use only a good grade hydraulic jack oil.
Avoid mixing different types of fluid and NEVER use
brake fluid, turbine oil, transmission fluid, motor oil or
glycerin. Improper fluid can cause premature failure
of the jack and the potential for sudden and immediate
loss of load. We recommend Mobil DTE 13M.
3. Fill with good quality jack oil. Reinstall oil filler plug/
screw.
Lubrication
Adding oil
1. A coating of light lubricating oil to pivot points, axles
and hinges will help to prevent rust and assure that
assemblies move freely.
2. Periodically check the pump piston and ram for
signs of rust or corrosion. Clean as needed and
wipe with a clean, oil soaked rag.
1. With saddle fully lowered and pump piston fully
depressed, set jack in its upright, level position.
Remove oil filler plug/screw.
2. Fill until oil is level with the filler plug/screw hole,
reinstall oil filler plug/screw.
Changing oil
Never use sandpaper or abrasive material on
these surfaces !
For best performance and longest life, replace the
complete fluid supply at least once per year.
1. With saddle fully lowered and pump piston fully
depressed, remove the oil filler plug/screw.
2. Lay the jack on its side and drain the fluid into a
suitable container.
Storage
When not in use, store the jack with pump piston and
ram fully retracted.
TROUBLESHOOTING
Symptom
Possible Causes
Corrective Action
• Ensure release valve tightly closed
• Remedy overload condition
• Release valve not tightly closed
• Overload condition
Jack will not lift load
• Release valve not tightly closed
• Overload condition
• Ensure release valve tightly closed
• Remedy overload condition
Jack bleeds off after lift
• Hydraulic unit malfunction
• Contact Omega Tech. Service
• Reservoir overfilled
• Linkages binding
• Drain fluid to proper level
• Clean and lubricate moving parts
Jack will not lower after unloading
Poor lift performance
• Fluid level low
• Air trapped in system
• Ensure proper fluid level
• With ram fully retracted, remove oil filler
plug to let pressurized air escape, then
reinstall oil filler plug
• Fluid level low
Will not lift to full extension
• Ensure proper fluid level
OIPM#13120-TJ2
4
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, Shinn Fu Co. of America, Inc. will repair or replace,
at its option, without charge, any of its products which fails due to a defect in material or workmanship, or which
fails to conform to any implied warranty not excluded hereby.
Performance of any obligation under this warranty may be obtained by returning the warranted product,
freight prepaid, to Shinn Fu Co. of America, Inc. Warranty Service Department, 10939 N. Pomona Ave., Kansas
City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law, (1) the
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS AS DESCRIBED ABOVE, and (2) Shinn Fu Co. of America, Inc. SHALL NOT BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE DURATION OF ANY AND
ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF ONE (1)
YEAR FROM DATE OF PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
OIPM#13120-TJ2
5
REPLACEMENT PARTS
Available Parts: Please refer to the Parts drawing when ordering parts. Not all components of the jack are
replacement items, but are illustrated as a convenient reference of location and position in the assembly sequence.
When ordering parts, give Model number, serial number and description below. Call or write for current pricing:
Shinn Fu Company of America, Inc. 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A. Tel:(888)332-6419
Model # 13120 & 13200
Parts No.
Description
Quantity
1
2
3
4
--
--
oil filler plug / screw*
handle assembly
return spring
saddle bracket
label(s) (not shown)
manual (OIPM # 13120-TJ2)
1
1
2
1
1
1
* oil filler screw for 13200
2
1
4
3
Figure 2 - Model 13120 & 13200 Replacement Parts Illustration
6
OIPM#13120-TJ2
Notes
Shinn Fu Company of America, Inc.
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel:(888)332-6419 Fax:(816)891-6599 E-Mail:[email protected] Omega Website: http://www.omegalift.com
Notes
Shinn Fu Company of America, Inc.
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel:(888)332-6419 Fax:(816)891-6599 E-Mail:[email protected] Omega Website: http://www.omegalift.com
|