Mitsubishi Electronics G 50a User Manual

Mitsubishi Electric Air-conditioner Network System

Central Controller

Model: G-50A

Instruction Book

Contents

……………………………………………

…………………………………

…………………………………………

1. Safety

2. Product feature

ON/OFF

3. Function

3-1 Specification

3-2 Display screen

4. User operation

……………………………

…………………………

^{…………………………………}10

CENTRAL CONTROLLER

G-50A

^{……………}11

4-1 Operation condition monitor

^{………………………}12

4-2 Operation setting

^…………12

4-2-1 Group operation setting

4-2-2 Collective operation setting

^………16

4-3 Timer operation ^{…………………………}19

4-4 Malfunction

^{………………………………}23

^{……………………}24

^{……………………………………}25

^…………25

4-5 Current time setting

5. Initial setting

5-1 Shifting to initial setting menu

^{…………………}25

5-2 M-NET address setting

^{…………………………}26

5-3 Function setting

^{……………}27

5-4 Group configuration setting

5-5 Interlocked operation setting

^…………29

^{……………………}31

5-6 Group name setting

^{……………………………}34

^{………………………}35

5-7 User setting

5-8 IP address setting

^…………35

5-9

Initial setting tools connection function

^{……………………………………}36

6. Maintenance

^{……………}36

6-1 Refrigerant system monitor

^{………………}37

6-2 Malfunction log monitor

^{…………………………}38

7. External input / output

7-1 External input function ^{…………………}38

^{…………………}39

7-2 External output function

Appendix 1 : Initial setting(adridged)^{…………………}40

^{…………………}42

Appendix 2 : User operation(adridged)

Before using the controller, please read this Instruction Book carefully to ensure

correct operation. Store this Instruction Book in a location that is easy to find.

1 . SAFETY

Please take a moment to review these safety precautions. They are provided for your protection and to prevent

damage to the controller.

This safety information applies to all operators and service personnal.

After you have read this manual, always observe the procedures described in the explanations and store it with

the installation manual in a location that is easy to find. If the controller is going to be operated by another per-

son, make sure that this manual is given to them.

Symbols and Terms

Statements identify condition or practices that could result in personal injury or loss of life.

Statements identify condition or practices that could result in damage to the controller or other property.

WARNING

CAUTION

Specific Precautions

WARNING

• Do not move and re-install the controller by yourself.

If installation is incorrect, it may cause an electric shock,

fire,etc. Ask your dealer or technical representative.

• Ask your dealer or technical representative to install.

If incorrect inatallation is done by a customer, it may cause

an electric shock, fire, etc.

• Securely install in a place which can withstand the

weight of the controller.

• Contact your dealer if the controller will not be used any

more or will be scrapped.

If it is not enough, the controller may fall and cause an

injury.

• Do not remodel or repair by yourself.

If the controller is redesigned or repair is not correct, it may

cause an electric shock, fire, etc.

• Make sure that the controller is connected to a rated

power supply.

Consult your dealer if repair is necessary.

If the controller is not connected to a rated power supply, it

may cause a fire or damage to the controller.

• Stop the operation immediately and notify the your deal-

er if an error code is displayed or malfunction occurs.

Fire or damage may be caused if the controller is operated

in this condition .

• Never remove the cover during operation.

Touching the charged parts of the controller may cause

severe burns or other personal injury.

• Stop the operation if any malfunction occurs.

If malfunction occurs (burning smell, etc.) stop the operation

and turn off the power supply. Contact your dealer or techni-

cal representative immediately. If the controller continues to

operate after a malfunction occurs, this may cause damage,

electric shock or fire.

CAUTION

• Do not use the controller in special environments.

The performance may be reduce or parts may be damaged

if the controller is used in locations subject to large quanti-

ties of oil (including machine oil), steam, sulfide gas.

• Do not install the controller in a place where inflam-

mable gas could leak.

If gas leaks and collects around the controller, it may cause

a fire or explosion.

• Do not touch the switches with sharp objects.

It may cause an electric shock or malfunction.

• Do not wash the controller with water.

It may cause an electric shock or malfunction.

• Do not touch the switch with wet hands.

It may cause an electric shock.

• Operate the controller within the specified temperature

range.

Observe the specified temperature range when operating

the controller. If the controller is used outside the specified

temperature range, it may cause serious damage. Be sure to

check the operation temperature range in the operation

manual.

• Do not use the controller for special applications.

This product is designed for use with the MITSUBISHI

ELECTRIC BUILDING AIR CONDITIONING CONTROL

SYSTEM. Do not use the system for other air condition man-

agement operation or applications. It may cause malfunc-

tions.

• Do not apply insecticide or flammable sprays to the

controller.

Do not place flammable spray near the controller and make

sure it does not blow directly on the controller as this may

cause in fire.

-1-

2 . Product Features

The central controller is capable of controlling up to 50 air conditioner units. It supports the following operating

function.

[ 1 ] User operating function

(1) Operation

1. Virtually almost functions operated by local remote controller are supported.

The central controller can be used to control the indoor units in specific group ON or OFF, select the operating

mode (COOL, DRY, FAN, AUTO and HEAT) for the indoor unit or HEAT RECOVERY, BY-PASS, AUTO for the

ventilation unit), select the fan speed, select the air direction (4 direction and swing operation), select the ventil-

ation mode (OFF, LOW speed, or HIGH speed), select TIMER MODE and select the temperature setting.

In addition, room temperature can be displayed at the unit of each group upon request.

(See 5-5 "User setting")

2. Local remote control operation can be prohibited for specific functions.

Access to specific control functions, such as ON/OFF operation, mode selection ,temperature setting and filter

sign reset operation can be prohibited for the local remote controls collectively or per group.

3. Collectively setting

Operation setting can be performs collectively or per group.

(2) Weekly Schedule

1. The weekly schedule enables four different schedule patterns to be set weekly per group. (P1-P4)

Of these, three patterns are to set ON/OFF schedule and remaining one pattern is to set the pattern to prohibit op-

eration of the local remote controller.

Four patterns (daily patterns) mentioned above enable the setting of individual schedule times for every group.

2. The respective daily patterns enable the setting of three different ON times (three prohibition times) and three

different OFF times (three permission times).

In addition, it is possible to set ON time only (prohibition time only) and OFF time only (permission time only).

3. Easy setting

Daily operation patterns and weekly schedules for one group can easily be copied to the other groups.

4. Timer automatic recovery operation when recovering from a power down is supported.

(3) Operating status monitor

1. ON/OFF/MALFUNCTION status can be monitored by group or by unit.

2. The groups managed by the central controller may be displayed all together by group number or group name

(first three characters). Collective display of all unit address is also supported.

3. When displaying all groups at once, individual groups can be turned ON or OFF by designating them by the

indicator .

(4) Malfunction monitor

1. The unit address where the malfunction occurred, the error code and address of the unit that detected

the malfunction are displayed on the malfunction monitor screen.

2. Pressing the reset key stops all the units connected to the same group, refrigerant system or linked group to the

unit where the malfunction occurred, all of these are reset.

-2-

[ 2 ] System configuration setup and maintenance function

(1) Setup for system configuration

1. Registration can be made for the indoor units, local remote controllers and slave system controllers in the same

group.

And also registration can be made for the ventilation such as OA processing unit.

2. Group name may be specified. ( Names may include alphanumeric characters.)

3. Group name may be copied.

4. Setting of group configuration and specifying the group name may be performed as long as power is being supplied

to the central controller. This mean that setting can be performed before the central controller is installed at

the site, before installation of individual units is completed or while the power supply to some units is cut off.

5. System configuration data setting in the central controller can be deleted at once if necessary when replacing cir-

cuits wired board, etc.

(2) Refrigerant system monitor

All unit address (indoor, outdoor, etc.) can be displayed for individual refrigerant system on the refrigerant system

monitor screen. This information is useful for checking the installation, such as address setting, transmission line

connection and power supply connection.

(3) Interlocked group setting

Setting can be performed for indoor units interlocked with a ventilation unit.

If even one of the indoor units interlocked with ventilation have started to operate, the ventilation will be activated.

(4) Malfunction log monitor

1. A log of the last 64 malfunction massage, in the order in which they occurred, can be monitored.

2. The data and time the malfunction occurred, the address of unit where it occurred, the error code and the ad-

dress of unit that detected the malfunction are displayed.

3. All malfunction logged in the memory of the central controller and indoor unit can be reset at once.

[ 3 ] Other

(1) Overall statues display lamp

Displays normal operation/all OFF/malfunction status for the entire system.

(Normal operation/all OFF/malfunction status is indicated by the lamp being lit, not lit or blinking respectively)

(2) Collective ON/OFF switch

This switch allows turning all of the unit in the system ON or OFF at once.

(3) Power supply wiring

The central controller is supplied power from the PAC-SC50KUA Power Supply Unit via the M-NET transmission line and

DC power line. The DC power between the PAC-SC50KUA Power Supply Unit and the central controller should be 10m

or less. The central controller allows to be connected to M-NET transmission line at any position. (M-NET transmission

line is the central control line which connects TB7 terminal of the outdoor unit)

(4) M-NET transmission line

The combined maximum distance between the outdoor units and the central controller, and between the outdoor units

and farthest indoor units connected to the same refrigerant system or their remote controller, may be extended up

500 meters.

Therefore, even if the total distance is made longer by installing the outdoor units all in row, there will be no problem

so long as the above maximum total distance limitation is not exceeded.

-3-

3 . Functions

3-1 Specifications

Item

Specification

DC24V,0.02A(Maximum loading)

Power received from PAC-SC50KUA Power Supply Unit via M-NET transmission line.

DC12V,0.2A(Maximum loading)

Power is received from the PAC-SC50KUA Power Supply Unit via the DC power line.

Input voltage

Source power requirement

0 ˚C +40 ˚C / 32 ˚F +104 ˚F

Operating

Temperature

Humidity

-20 ˚C +60 ˚C / – 4 ˚F +140 ˚F

Non operating

Environmental condition

Dimensions

30 90%RH (No condensation)

120(H) 300(W) 80[*19](D)

4-3/4(H) 11-13/16(W) 3-1/8[*3/4](D)

*[ ] : indicate the thickness from the

wall.

Kg 1.0

lb 2-1/4

Weight

System condition

Indoor unit or independent OA processing unit or LOSSNAY

: 50 units maximum (50 groups maximum)

Number of units (indoor or independent OA processing unit or LOSSNAY) in one group

: 1-16 units

*Note

Indoor unit, independent OA processing unit and LOSSNAY can not

Number of remote controllers in one group

: 1-2

Number of control unit *3

Number of system controllers in one group

: 0-4 (including the number of remote controller in one group)

: 0-3 for groups which have one remote controller.

Number of indoor units interlocked with one OA processing unit or LOSSNAY

: 0-16 (some types of OA processing unit can only be operated when inter-

locked to a maximum of 9 units)

User operating function

ON/OFF

The ON/OFF operation can be performed as a collective or per group.

The switch operation for the operation mode setting can be performed as a collective

or per group.

[ Selectable operation mode for the indoor unit ]

Operation

mode

Cool/Dry/Fan/Auto/Heat

[ Selectable operation mode for the independent ventilation ]

Heat recovery/By-pass/Auto

The switch operation to set the High and Low speed can be performed as a collective

or per group.

( The 4 fan speed setting is available to the indoor that has 4 levels )

Fan speed

Operation

Air direction

and swing

operation *1

The air flow direction can be switched to 4 directions and swing operation as a collec-

tive or per group

Temperature setting can be performed collectively or per group.

[Setting temperature range]

Temperature

setting

Cool (Dry) operation

Heat operation

: 19 30 ˚C / 67 87 ˚F

: 17 28 ˚C / 63 83 ˚F

: 19 28 ˚C / 67 83 ˚F

Auto operation

-4-

Item

Prohibit local

remote

control

Specification

The specific functions of a local remote controller can be prohibited as a collective or

per group.

[Prohibit function]

ON/OFF operation, Operation mode setting, Temperature setting and Filter sign

reset operation.

The set schedule operations can be switched to ON/OFF (local remote controller

operation prohibition/permission) for each group.

Timer operation

Operation

Filter sign

reset

The filter sign reset operation after the air filters are cleaned can be performed as a

collective or per group.

The ventilation operation of the interlocked OA processing unit or LOSSNAY can be coll-

ective or per group.

Ventilation

[Ventilation operation]

operation

Low speed/High speed/Ventilation OFF

Collective

operation

The overall status lamp displays conditions of the collective statues.

Each group

operation

Each group operation is displayed on the operation setting screen (group) or operation

monitor screen.

Operation

mode

Fan speed

Air direction

Temperature

setting

Timer

operation

Filter sign

Local remote

control

Monitor

Displayed on the operation setting screen (group).

prohibition

Ventilation

operation

Room

temperature

display

Central control

prohibition

External

input signal

condition

The unit address and error code are displayed on the malfunction monitor screen when

a malfunction occurs.

Malfunction

When the power is cut off, the current time is backed up for approximately one week.

(When the controller is fully charged. The controller is fully charged by twenty-four

hours after power feed.)

Current time

back-up

Operation pattern setting can be performed.

• Operation interval : Minimum 10 minutes

• The daily operation pattern and weekly schedule for each group can be set.

• A pattern of one day : P1/P2/P3/ P1 / P2 / P3 / P4 / -

* ON/OFF setting up to three times a day are possible for P1/P2/P3.

* P4 enables to set operation prohibition of 3 times per day for the remote controller.

* P1 / P2 / P3 implement the schedule which has combined P1/P2/P3 of ON/OFF

Other

Timer setting

pattern and P4 of remote controller operation prohibition pattern together.

( P1 = P1 + P4 / P2 = P2 + P4 / P3 = P3 + P4 is displayed.)

* - is a day without timer operation.

• "The reference temperature and set-back value" or "Setting temperature" which are

linked with timer operation can be set.

-5-

Item

Specification

Group name can be specified and display on the operation setting screen.

* Group name setting is need at the initial setting.

Group name

designation

External

signal input

interface

Emergency stop/normal, ON/OFF, prohibit/permit for local remote operation can be

controlled for units being controlled with a non-voltage contact signal input from an

external source.

Other

When one or more units being controlled are operating, the "ON" signal will be out-

put, and if a malfunction occurs in one or more units, the "malfunction" signal will

be output.

External

signal output

interface

Initial setting (for installation and maintenance)

The group setting operation for units (indoor units local remote controllers, independ-

Group setting ent OA processing unit, LOSSNAY and slave system controllers) are performed on

Connecting

information

setting

the group setting screen.

Interlocked

setting

The interlocked setting for the ventilation equipment as the OA processing unit or

LOSSNAY , etc to indoor unit is performed on the interlocked setting screen.

Malfunction

history

A maximum of the 64 most recent malfunction are displayed on the malfunction log

monitor.

Monitor

Refrigerant

system monitor

The connected unit address are displayed on the refrigerant monitor screen.

Some of the indication and function that appear on the each screen can be specified to

match the needs of the user.

User setting

Master system

controller/

Slave system

Master/Slave setting of the system controller.

* G-50A does not support slaves.

controller

setting

Prohibition

setting enable

/disable

The setting of a system controller which the local remote control is prohibition enable or

disable.

Other

The prohibited

controller

range setting

Selecting of the prohibited controller which is only local remote controller or both

local remote controller and the other system controller.

K-control

type

The system composed of K-control type air conditioner equipment can be controlled

using the K transmission converter (PAC-SC25KAA)

*1 Each operation is available in accordance with the function of unit.

*2 Master system controller and slave system controller.

* G-50A does not

support slaves.

M-NET Gateway

management range

G-50A

management range

Another system controller

management range

Management range

of G-50A

Unit

When G-50A controls another system controller or when

the system contains only G-50A :

When G-50A is controlled by another system controller :

(Example: MJ-300Gateway)

G-50A is set as the master system controller.

G-50A is set as the slave system controller.

* G-50A performs the group setting in this configuration.

* The group setting is performed by Master system

controller.

*3 OA processing unit (LOSSNAY) and the K transmission converter (PAC-SC25KAA) are not included in systems

shipped to North America (USA & Canada).

-6-

NOTE :

The following group setting cannot be performed.

• Unit groups which are not under the management of the master controller and are managed by the slave

system controller.

Master system

controller

Slave system

controller

Group

• A common group is managed by more than two master controllers.

Master system

controller 1

Master system

controller 2

Group

• A slave system controller which exceeds the management range of the master system controller of two or

more.

Slave system

controller

Master system

controller 1

Master system

controller 2

Group

-7-

Overall status lamp

3 - 2 Display Screen

The lamp indicates the unit op-

eration condition.

……

OFF

During operation

All group are stopping

……

BLINKING

Malfunction

Display

0022

PROHI

BITED

G-50A

NOTE: The temperature setting includes

a function to switch the display

between

Celsius

(

Fahrenheit (

˚F) (page 34).

Continuously press

and

(2 seconds or longer)

ENTER

001

MON

04-2002

P 4

-8-

The collective operation switch can be per-

formed in the user setting mode for any screen.

( Excluding menu screen )

Collective operation switch

If this switch is pressed during

the operation, a whole group stop

is performed.

LAN changeover switch

Refer to section "5. Initial setting ( page 25 ) " for

explanation of the operation of these switches.

LCD contrast adjustment knob

LAN status lamp

Orange LED indicates action and green LED indicates link.

Service LAN connector

Refer to section "5. Initial setting " for an explanation of this connector.

Rear side

Ethernet

M-NET

POWER

RS232C

CN1

CN2

12VDC GND

Operation

panel

RS-232C connector

M-NET Transmission

line terminal

External input / output interface connecter

Refer to section "7. External input / out-

put function ( page 38 )" for the detail

of operation of these connectors.

LAN(Ethernet)connector

DC power supply terminator

IP address setting

Function select setting

M-NET address setting

FUNCTION SELECTS

ADDRESS SETTING

IP ADDRESS SETTING

IP ADDRESS :

M-NET ADDRESS: 000

6 ADDRESS SETTING

7 FUNCTION SETTING

8 IP ADDRESS SETTING

192.168.001.001

MASK ADDRESS:

255.255.255.000

OFF

Displays, or sets, the controller

M-NET address.

Refer to section "5. Initial setting

(page 25)" for a detailed explan-

ation of operation.

Sets the function of the controll- Sets the LAN IP address.

er.Refer to section "5. Initial set- Refer to section "5. Initial setti-

ting(page 25)" for a detailed ex- ng(page 25)" for a detailed ex-

planation of operation.

VER.

BACK

GROUP NO

NONE

2002

16-04-2002

014 6602

2002

12 : 45

(DETECT 014)

INDICATE

05-04-2002

012 6607

09 : 12

(DETECT 012)

INDICATE

1-1-2001

2002

NONE

TEMP. UNIT ˚C / ˚F

LOSSNAY

that

Maintenance

-9-

4 . User operation

Used the following two screens when user operation is performed.

.......

Operation monitor screen

This screen displays ON/OFF and malfunction condition of unit.

G-50A normally displays this screen.

The unit operations can be performed by individual group or collective

........

Operation setting screen

operation. These operation include the ON/OFF, operation mode, fan speed,

temperature setting, air direction, ventilation setting, timer operation

ON/OFF, local remote controller prohibition and filter sign reset are

performed by group or collectively. In addition, this screen can also displays

the room temperature of each group.

• The collective operation can be performed on any screen (except for the menu screen) in the user operation

mode

Press the

switch and

Press the

switch and

select "2. OPERATION SETTING"

select "1. OPERATION MONITOR"

BACK

SCREEN

Press the

switch.

ENTER

Press the

switch.

switch to set

"MON. (MONITOR)" on the blinking

ENTER

display and press the

switch.

(Individual group

operation setting

screen)

The unit operation can be verified in

a single glance.

Press the

switch

to set "COL. (COLLECTIVE)" or

"GROUP" on the blinking display

ENTER

and press the

switch.

Refer to section "4-1 Operation

condition monitor".

BACK

SCREEN

Press the

(back screen) switch.

(Collective

operation

setting screen)

Each unit operation

setting is performed.

Refer to section "4-2 Operation setting".

-10-

4 - 1 Operation condition monitor

• This function displays the ON/OFF/Malfunction status of specific units or group.

• ON/OFF/Malfunction status is shown by the indication corresponding to the unit or group appearing in inverse,

normal or blinking display.

• The user may select display items by unit address, group number or group name.

Refer to section "5-7 User setting (page 34)" for detail of user setting.

• During the user operation mode, this screen returns from any screen if there is no operation for approximately

10 minutes.

(1) Operation Method

• Note that operation is different for each of the following display methods.

GROUP

SELECT

Press the

switch to change the display group in desired opera-

tion and monitor.

ON/OFF

When displaying the units in a given group, press the

all the units in that group ON or OFF.

switch turn

Press the

number to be operated.

switch to move the " " select the group

ON/OFF

Press the

switch to set the displayed group unit is indicated by the

" symbol to the on/off mode.

1 Press the

switch to move the " " symbol. Select

the group name to be operated.

ON/OFF

Press the

switch to set the displayed group unit is indicated by the

" symbol to the on/off mode.

*Displays up to the first 3 characters of the set group name.

(2) Display contents

Reverse:ON

Normal:OFF

Blinking: Malfunction during

units is off

Blinking and Reverse:

Malfunction during

unit is on.

*When a malfunction occurs, refer to section "4-4 Malfunction (page 23) ".

-11-

4 - 2 Operation setting

• There are two methods for the operation, performing the operation classified by groups or collective operation.

4 - 2 - 1 Group operation setting

Ventilation

No. Name of switches

Function

Display

Operation status display

The ON/OFF condition of the dis-

played group is switched.

ON/OFF switch

*When there is an interlocked OA processing unit

or LOSSNAY , turning this switch ON starts

operation in a [High] ventilated state.

Each time to push the switch, a mode is selected in

a sequence that goes from COOL, DRY, FUN,

AUTO, HEAT and beck to AUTO for air conditioner

group.

Used to the type of the operation

mode selection.

Note:

Operation mode can be selected ac-

cording to the function of unit.

If the unit is only cooling type.

HEAT/AUTO mode may not appear

on the display.

Operation mode

switch

On the group composed of independent LOSSNAY ,

operation mode is selected in a sequence that goes

from HEAT RECOVERY,AUTO, BY-PASS and back

to HEAT RECOVERY.

Refer to the instruction manual of

the air conditioner for more detail.

Fan speed display

4 levels

The fan speed can be switched to four

levels. Switching may be 3 levels or 2

Fan speed

switch

levels, depending on the model.

2 levels

3 levels

The setting temperature display.

The setting range change according to the operation

mode.

COOL/DRY

HEAT

AUTO

19 30 ˚C / 67 87 ˚F

17 28 ˚C / 63 83 ˚F

19 28 ˚C / 67 83 ˚F

Temperature

setting switch

The setting temperature change is per-

formed.

NOTE: The temperature setting includes a function

to switch the display between Celsius (°C)

or Fahrenheit (°F) (page 34).

-12-

Function

Display

No. Name of switches

These switches are used when the cur-

rent time is set.

Current time

Refer to section "4-5 Current time setting" .

setting switch

The Air flow direction can be selected.

The air flow direction can be selected

to four directions and swing operation

(auto vane).

Air flow direction

Air direction

setting switch

The operation mode of the interlocked

ventilation can be performed.

*Where there is no interlocked ventilation,

Ventilation volume setting display

Ventilation

setting switch

the operation of this switch is invalid.

"Ventilation" is OA processing unit or LOSSNAY

PROHIBIT : Local remote control specified on the

prohibit setting screen is not possible.

PERMIT : Local remote control is possible.

Remote

Used to prohibit for the local remote

control.

operation

prohibit switch

The timer operation can be performed

according to a previously set operation

pattern.

Timer operation display

Timer more

switch

OFF

The filter sign display reset is per-

formed.The reset processing is com-

pleted by pressing this switch two

times.

Filter display

Filter

Reset switch

No display

Group number display

This switch displays 1 50 group numbers.

Group select

switch

The display group is changed.

The switch can also display group names.

Back screen

switch

The menu screen will be returned.

The cursor position (blinking) moves.

Use to back to the user menu screen.

The position of a cursor can be moved

when a cursor is appear.

Cursor position

switch

*1: Room temperature can be displayed by selecting the room temperature display function per "5-7User

Setting".( but limited to indoor unit group)

-13-

(1) Local remote control operation prohibition setting.

• G-50A can prohibit the operation of item such as connected local remote controller or slave system controller

for each group. The prohibit items are ON/OFF operation, operation mode, temperature setting and filter sign

reset operation.

GROUP

SELECT

Press the

switch to display the group that the operation

prohibition setting will be performed.

Press the

switch to set "PROH. (PROHIBIT)" on the

ENTER

blinking display and press

switch.

The prohibit setting screen is displayed.

Press the operation switch for the items to be prohibited.

ON/OFF

• When the ON/OFF operation is to be prohibited :

• When the operation mode is to be prohibited

MODE

• When the setting temperature is to be prohibited :

• When the filter sign reset is to be prohibited

RESET

DEL.

The items selected for prohibition are shown in reverse display.

BACK

SCREEN

After setting of prohibit item, press the

operation setting screen.

switch to go back to the

The operation setting screen is displayed.

Remote operation prohibition/permission display will

be change PERMIT to PROHIBIT and the pro-

hibited item set on the prohibit setting screen are

shown in reverse display.

REMOTE

PROHIBITION

Press the

ON " .

switch to set "PROHIBIT

The prohibit setting is completed.

• The system controller that performed the local remote control operation prohibition setting can

operate the prohibited items.

NOTE:

• When the No.4 function select is set ON, the prohibit setting of the local remote control operating

cannot be made. For details, refer to "5-3 Function setting."

-14-

(2) G-50A operation prohibition

• The operation of this controller is prohibited when an operation prohibition setting for this controller is received

from a system controller other than this controller or when an external input signal is used.

PROHI-

BITED

The

is displayed and the prohibition operation is display in re-

verse display when operation of this controller is prohibited by another

system controller or an external input signal used.

The prohibition operation which is displayed in reverse display is not

possible to operate in this condition.

(3) Using the function area

To select the function from the function area, use the

switch to move the cursor to the blinking to

ENTER

the function of your choice and press the

on screen.

switch. The current cursor position appears as a blinking indication

• MON. (MONITOR)

• PROH. (PROHIBIT)

• COL. (COLLECTIVE)

• M (memory)

: Shift to the operation monitor screen

: Shift to the prohibit setting screen

: Shift to the collective operation setting screen

: Stores the setting currently shown on the screen in memory.

: Reads the setting stored in memory and activates them for the currently dis-

played group.

• MR (memory read)

-15-

4 - 2 - 2 Collective operation setting

• A collective operation setting and a collective prohibit setting can be performed for all the group managed by

this controller at one time.

(1) Collective operation setting

1 Press the

switch to set "COL. (COLLECTIVE)" in blinking

ENTER

display and press the

screen.

switch on the group operation setting

The collective operation setting initial screen is displayed.

Select the items for operation setting on the collective operation setting

initial screen.

The operation method is same as described in section "4-2-1 Group

operation setting" (Page 12).

The items which were not set, remain set to the same

condition that were set before the collective operation was

performed.

NOTE:

The items selected for the operation blink on the collective operation

setting screen.

When all setting are completed, press the

switch to display

the "SET" in blinking display for the indicated function area.

ENTER

Press the

switch one time to complete this setting.

The collective setting is completed when the previous

items light. (After the setting are completed, start

The collective setting is executed.

The collective setting takes approximately 20

seconds.

from step

to perform operation again if change

operation are required.)

The display of setting contents is erased

NOTE:

when shift to another screen.

-16-

(2) Collective prohibit setting

1 Press the

switch to set "PROH. (PROHIBIT)" in blinking

ENTER

display and press the

initial screen.

switch on the collective operation setting

The collective prohibit setting initial screen is displayed.

Select the items to be prohibited or permitted on the collective prohibit

setting initial screen.

Each time to press the switch corresponding to the prohibition item,

the prohibition or permission is selected.

Prohibition setting : The prohibited item is displayed in reverse with

blinking.

Permission setting : The permitted item is displayed with blinking.

The selection method concerning to prohibit/ permit item is same as de-

scribed in section "4-2-1 (1) Local remote control operation prohibit

setting". ( page 14 )

The items selected for the prohibition or permission are displayed with

blinking.

And the "SET" is displayed with blinking in the function area.

ENTER

When all setting are completed, press the

plete this settings.

switch one time to com-

The collective prohibit setting is excused.

The collective prohibit setting takes approximately

20 seconds.

The collective setting prohibition/permission item

setting is completed when the previous item light.

After setting of prohibit/permit items, press the

BACK

SCREEN

switch to back to the collective operation

setting initial screen.

-17-

The collective operation setting initial screen is displayed.

REMOTE

PROHIBITION

Press the

switch to set "REMOTE CONTROL PROHIBIT ".

11Remote operation prohibition/permission display ("REMOTE CONTROL

PROHIBIT " ) is displayed with blinking.

Press the

switch to display the "SET" in blinking display

for the indicated function area.

ENTER

Press the

ting.

switch one time to complete the collective prohibit set-

The collective prohibit setting is executed.

It takes approximately 20 seconds.

The collective prohibit setting is completed when the remote operation

prohibition/permission display is change to be light.

• The display of setting contents is erased when shift to another screen.

NOTE:

• The following restrictions in the collective operation settings.

1. Temperature setting

The range that can be set falls within 19˚C 28˚C /67˚F 83˚F regardless of the operation mode.

2. Operation mode selection, fan speed selection, air direction, etc.,can be collectively set regardless

of the functions of the unit. However, actual setting to a unit without functions cannot be performed.

To obtain the correct setting contents, refer to the respective group operation setting screens.

-18-

4-3 Timer operation

• A weekly schedule setting can be specified for each group.

• Possible to set on the timer the schedule to prohibit operation of the local remote controller in addition to ON/OFF

schedule.

• Always set to current time on the current time setting screen when the schedule setting is performed.

Refer to section "4-5 Current time setting".

When browser monitoring, or schedule setting from central monitoring

NOTE: _{PC, was performed, the timer screen of this function cannot be used.}

"This function is set from a higher level." is displayed on this screen.

The ON and OFF (PROHIBITION and PERMISSION) times can set in 10-minute units.

The daily operation schedule can include up to three ON (PROHIBITION) time settings and three OFF (PERMISSION)

time settings.

Three types (P1-P3) of daily ON/OFF pattern and one type (P4) of prohibition/permission pattern are available

respectively, each of which can be set every to each group.

Week day which is not set in timer pattern is displayed with (-).

In addition, it is also possible to set the schedule which has combined P1 -P3 and P4 together .

( P1 / P2 / P3 ) In this case, both of ON/OFF pattern and prohibition/permission pattern are daily executed.

Any one of these options may be selected for each separate day of the week.

The schedule patterns can be copied easy to other group by the memory and memory read functions because the

schedule contents can be recorded in the memory.

The setting temperature or set-back value setting can also be supported during timer operation.

BACK

SCREEN

Press the

switch to select

Press the

switch to go back to

"3 SCHEDULE SETTING".

the user operation menu screen.

• The schedule contents of each

group can be monitor.

• Weekly schedule pattern setting

can be performed.

Press the

switch to move the cursor position

to P1 (or P2 or P3 or P4 ).

BACK

SCREEN

Press the

switch.

(The "P1" indication blinking.)

ENTER

And press the

switch to the

P1 (Pattern 1) Schedule pattern

setting screen.

• Schedule pattern (P1 P3 , P4 )

setting can be performed.

-19-

(1) Schedule pattern (P1 P3) setting

• Follow the procedures described below to set each daily schedule pattern for each group.

• The setting temperature or set-back values setting are also performed in the schedule setting operation. To enter

the setting temperature or set-back value setting select SET-BACK or SET TEMP. Accordance with section "5-7

user setting (page 34)" in advance.

• The setting temperature or set-back value selected in this way take effect only during timer operation.Also set-

back operation is cancelled if the setting temperature is changed using this central controller or a local remote

controller.

( The set-back operation resumes at the next timer-ON time )

GROUP

SELECT

Press the

setting.

switch to display the group in desired a timer

switch to move the cursor position to

Press the

the pattern ( P1 P3, P4 ) to be setting.

ENTER

Press the

switch one time.

The schedule pattern setting screen is displayed.

Press the

switch to move the cursor position to

the first ON (PROHIBITION) time.

CLOCK / PATTERN

Press the

switch to select the ON (PROHIBITION)

time. (time is changed by 10 minutes unit.)

ENTER

Press the

switch one time to set ON (PROHIBITION) schedule.

(The cursor moves to the next setting position.)

Perform operation to select OFF (PERMISSION) time.

Perform operation to set the OFF (PERMISSION) time.

10Repeat operation to to set the second and third ON/OFF (PRO-

HIBITION/PERMISSION) schedules in the same manner.

When the second or third ON/OFF (PROHIBITION/PERMISSION) sch-

edule is not used, the characters "

" remain display and press

ENTER

the

switch one time.

To cancel the ON/OFF (PROHIBITION/PERMISSION) time that was set

previously, use the switch to move the cursor

to the time position to be cancelled and press the

RESET

DEL.

switch.

When the P1 setting are completed,perform operation to as nec-

essary to perform the setting for P2 or P3 or P4 .

Setting example in case of P4

-20-

(2) Set-back values and setting temperature setting

• Setting the set-back values and setting temperature can be performed only when selecting either "SET BACK"

or "SET TEMP" on the user setting screen in the initial setting mode.

• Set-back operation

Set-back operation is a method which reduces the air conditioner running cost by controlling the operation with

specified time band for lowered load. In other words the unit operates at a few degrees higher for cooling and

a few degrees lower for heating in the specified time band.

EXAMPLE When the reference temperature is 24˚C / 75˚F and the set-back value is set to 2˚C / 4˚F.

• Cooling operation : 24˚C+2˚C=26˚C / 75˚F+4˚F=79˚F

• Heating operation : 24˚C-2˚C=22˚C / 75˚F-4˚F=71˚F

• Setting temperature operation

This operation sets the temperature when timer ON is set to a predesignated temperature regardless of the op-

eration mode.

Press the

switch to move the cursor posi-

tion to the set-back reference

temperature or setting tempera-

ture.

NOTE: The temperature display

can be switched between

Celsius (°C) or Fahrenheit

(°F) (page 34).

Press the

(CLOCK/PATTERN) switch to

select the following items.

• Set-back value;

The reference temperature and

set-back value for each ON time

period are selected.

• Setting temperature:

The setting temperature for

each ON time period is selected.

ENTER

Press the

setting.

switch to make

Repeat operations and

* The selecting range:

set the set-back value or setting

temperature for each ON/OFF

schedule.

• The reference temperature for set-back operation

: 19˚C 28˚C (1˚C unit) / 67˚F 83˚F (2˚F unit)

: 0 9 degree (1 degree unit)

• The set-back value

/ 0 18 degree (2 degree unit)

BACK

SCREEN

: 19˚C 28˚C (1˚C unit) / 67˚F 83˚F (2˚F unit)

• The setting temperature

Press the

hed.

switch, when finis-

(3) Weekly schedule setting

The schedule pattern P1 to P3, local remote control prohibition (P4), P1 to P3 of a composite pattern composed of

P1 to P3 and P4, and non-timer operation(-) are set for each day.

GROUP

SELECT

Press the

switch to display the group in desired weekly

schedule setting.

Press the

switch to move the cursor to the pat-

tern position to be set.

-21-

Press the

P4 or ( - ).

(CLOCK/PATTERN) switch to select P1 to

ENTER

Press the

switch one time to complete the setting.(The cursor

will move to the next setting position. )

Repeat operations and to assign the schedule pattern to each

day.

When the No.4 function setting is set ON, P4 cannot be set.

NOTE:

(4) Copying schedule content to other groups (memory,memory read)

• The schedule pattern P1 to P3, weekly schedule pattern, set-back value or setting temperature of one group

can be recorded and copied to memory or to another desired group.

• Correction and modification can be easily performed after the copy operation is completed.

Display the original group on the weekly schedule setting screen.

Press the

switch to move the cursor to "M" .

ENTER

Press the

switch one time to record the setting date in memory.

*To erase date from the memory, return to the user operation menu

screen.

"M" is displayed in reverse with blinking.

GROUP

Press the

switch to select the group to which the data is

SELECT

to be copied.

Press the

switch to move the cursor to "MR" .

ENTER

Press the

switch to set the contents which will be the same as the

setting data in memory.

The same contents are displayed.

The contents stored in memory can be copied to other groups any number

of times because these contents will not be erased even if the memory read

operation is used.

-22-

4 - 4 Malfunction

• The malfunction monitor function is used for conforming to the details of the malfunction condition when a

malfunction is displayed on the operation monitor screen.

• The malfunction monitor function can display data describing up to nine malfunctions in the address number se-

quence on one page. This data contains the unit address where the malfunction occured, the error code and the

unit address where the malfunction was detected.

• After checking the unit address where the malfunction occurred and the error code, please contact your dealer

or technical representative as soon as possible.

< Shifting to the malfunction monitor screen >

BACK

SCREEN

Press the

switch to

Press the

switch to go back

select "4 MALFUNCTION MONITOR".

to the user operation menu screen.

The unit address

where the malfunction was detected

where the malfunction occurred

Error code

When there is no malfunction taking place, [ NO ERROR ] lights up instead of [ ERROR CODE ].

NOTE :

Page change operation

The page change operation is performed by the

switch.

Pressing the

switch shows the current display page +1.

switch shows the current display page -1.

Malfunction reset operation

RESET

DEL.

Press the reset

switch to reset all malfunctions.

The reset operation can be performed on any page.

When operation of the G-50A is prohibited, reset operation is invalid.

NOTE :

-23-

4 - 5 Current time setting

The current time, day, month and year are set on the current time setting screen.

< Sifting to the current time setting screen >

BACK

SCREEN

Press the

switch to back to

Press the

switch to select

the user operation menu.

"5 CURRENT TIME SETTING".

04-2002 MON

Press the

switch to move the cursor position to be set.

(CLOCK/PATTERN) switch to set the num-

Press the

ber or day that is displayed.

04-2002 MON

Repeat operations and to set the date day, month, year and

time.

ENTER

Where all setting have been completed, press the

switch.

The current time setting is executed and "done" is displayed with

blinking for two seconds to indicate the current time setting completed

and the clock count will start with the second reset to 0.

2002 SUN

-24-

5 . Initial setting

5 - 1 Shifting to initial setting menu

• Shift to the initial setting menu by continuously pressing

(2seconds or longer) on the user operation menu

(2seconds or longer) on the initial setting screen

screen.(Refer to section "3-2".)

Shift to the user operation menu by continuously pressing

(Refer to section "3-2".)

• When group information is not saved, the following initial setting screen is displayed when power is turned on at this

controller.

WED 15:29

ADDRESS SETTING

FUNCTION SELECT

IP ADDRESS SETTING

GROUP SETTING

PLEASE SET

INITIAL SETTING

5 - 2 M-NET address setting

(1) Select

"6.ADDRESS SETTING"(or

"1.ADDRESS SETTING).

INS.

(2) Set the controller address by pressing the

switches.(000,201 250).

BACK

SCREEN

(3) When the

switch is pressed after setting, the screen returns.

Press the

switch

WED 15:29

to select"6ADDRESS M-NET ADDRESS

SETTING"

M-NET ADDRESS: 000

ADDRESS SETTING

FUNCTION SETTING

IP ADDRESS SETTING

BACK

SCREEN

Press the

switch to back

to the initial

setting menu.

BACK

• When the controller is shipped from the factory, the address is set to "000".

(Always set the address to "000" When the K transmission converter is managed.)

Observe the following precautions when this controller manages the M-NET models and K control mod-

els by using the K transmission converter (PAC-SC25KAA).

NOTE :

Refer to the K transmission converter instruction manual for further details.

• Address of this controller

Always set the address of this controller to "000" .

• Function select setting of this controller

Always set the No.3 function setting to ON.

• Indoor unit address

Set all the M-NET models of indoor units from 001, next, set the address of the K control indoor unit.

001 M-NET indoor unit maximum address

mum address 050

K control indoor unit mini-

Indoor unit address

* The K transmission converter (PAC-SC25KAA) is not included in systems shipped to North America

(USA & Canada).

-25-

5 - 3 Function setting

• The functions of this controller are set according to the function settings.

• The functions selects are set to OFF when the controller is shipped from the factory.

(1) Select

"7.FUNCTION SETTING"(or

"2. FUNCTION SETTING").

(2) Switch the function by pressing the function No. you want to change, or the

of the same number.

switch

Each time the switch is pressed, the ON/OFF state of that No. is switched. (NO. 1 and NO. 2 cannot be changed.)

1)When Input

switch was pressed.

OFF

: Active

BACK

SCREEN

(3) When the

switch is pressed at the end of function switching, the screen returns.

Press the

switch

WED 15:29

FUNCTION SETTING

to select"7FUNCTION

SELECT"

ADDRESS SETTING

FUNCTION SETTING

IP ADDRESS SETTING

OFF

BACK

SCREEN

Press the

switch to go back

to the initial

setting menu.

BACK

No. 1

No. 2

No. 3

No. 4

No. 5

No. 6

No. 7

Reserved for future use (Leave this switch set to OFF)

OFF : No K transmission converter installed

OFF : Operation prohibit setting valid

ON : K transmission converter installed

ON : Operation prohibit setting invalid

ON : Emergency stop broadcast disabled

OFF : Emergency stop broadcast enabled (Be sure to use)

External input changeover (refer to section "7 External input/output function")

No. 8

The range of a controller which the operation is prohibited

OFF : Both of the system controller and the local remote controller ON : Only the local remote controller

-26-

5 - 4 Group configuration setting

• Registration can be made for the indoor units, local remote controllers and slave system controllers in the same

group.

• Registration can be also performed for the group which is composed of only OA processing unit or LOSSNAY.

( Independent ventilation group )

< Example for the group configuration >

Outdoor unit

Indoor unit

M-NET local remote controller

OA processing unit or LOSSNAY

M- NET

Transmission line

Independent ventilation group

Air conditioner group

• Supply the power from the power supply unit (PAC-SC50KUA) through the M-NET transmission line and DC line.

• Perform the following procedures to set the group configuration because the interlocked operation setting will

not be performed if the group configuration settings have not been performed.

When the power is supplied to the controller, the screen shown on the

left is displayed.

WED 15:29

1 ADDRESS SETTING

2 FUNCTION SETTING

3 IP ADDRESS SETTING

4 GROUP SETTING

Press the

(or

) switch to select "1 GROUP SETTING" .

(or "4 GROUP SETTING")

PLEASE SET

INITIAL SETTING

The group configuration setting screen is displayed.

GROUP

SELECT

Press the

switch to display the group number to be set.

switch to move to move the cursor to the

address display position to be set.

Used the numeric keypad switch to set the address of the indoor

unit, local remote controller, slave system controller in the display

group number.

< Operation example >

When the indoor unit which address is 012.

1) Input "0"

2) Input "1"

3) Input "2"

4) Press the

012

switch 012

* It is also possible just enter "1" "2" .

< When the input is incorrect >

Before pressing

switch, continue to input the data. After pressing

switch, move the cursor to the addresses to be deleted and press

RESET

DEL.

the

switch to delete these addresses.

• Do not set interlocked ventilation unit such as OA processing unit or LOSSNAY.

• Even if the addresses are input any order, it is switched to a sequence starting with low-order ad-

dress.

NOTE:

• The independent ventilation unit can not set to the indoor unit group and it can not be set to as an

interlocked ventilation unit.

-27-

Set all the units and controllers to be registered in the displayed group

number.

Repeat operation to to set all groups managed by this control-

ler.

BACK

SCREEN

When all setting are completed, press the

switch.

• When there are M-NET local remote controllers in the

system,always be sure to set the local remote controller

address. The local remote controller will not operate if

the address setting is not performed.

NOTE:

However, when the local remote controller is an MA remote

controller (PAR-20MAA) or K-control type remote controller,

setting is not performed.

• If there is a K transmission converter is a component

in the system, do not perform the group configurations

setting of this controller for the K transmission converter.

The following initial setting screen is displayed.

When the interlocked operation settings are performed, refer to section

"5-5 Interlocked operation setting".

WED 15:29

When the group name settings are performed, refer to section

"5-6 Group name setting".

When the user settings are performed, refer to section "5-7 User setting".

Group configuration date collective deletion

Additions

DEL.

• Display "G00" in the group configuration setting screen and press the

switch two times continuously to

delete the all group configuration data and all interlocked operation data.

• When this unit is set to the slave system controller by the function select , group registration can not be

made. However confirmation of the contents of group registration is possible.

NOTE:

•

Simultaneously press the

and

keys on the user operation menu screen for 2 seconds to perform group

configuration setting. The initial setting menu screen is displayed. Select "1. GROUP SETTING" on the setting

menu screen, wait for the group setting screen to appear, and change the setting.

When the necessary initial settings are complete, simultaneously press the

and keys on the user operation menu screen for 2 seconds.

When returned to the user operation screen, register processing for the group

configuration information and initial set up processing for each unit and each

controller is executed.(This process takes approximately 5 7 minutes.)

-28-

5 - 5 Interlocked operation setting

• Registration of interlocked operation of Ventilation unit (OA processing unit and LOSSNAY) with single or multiple

indoor unit is performed. All indoor units to be interlocked with ventilation unit for operation should be registered

for the interlocking with ventilation unit.

Outdoor unit

Indoor unit

M-NET local remote controller

OA processing unit or LOSSNAY

M-NET

Transmission line

Simultaneously press the

screen for 2 seconds.

and

keys on the user operation menu

Always perform the mode change operation from the user oper-

ation menu.

NOTE:

Mode change operation from other screens is ineffective even if

performed.

Initial setting menu screen is displayed.

Press the

switch to select "2 INTERLOCKED SETTING" .

The interlocked setting screen is displayed.

Minimum address of the interlocked OA processing unit or LOSSNAY unit

which can be set to interlock with indoor unit is displayed on the "INTERL-

OCKED UNIT ADDRESS" display position. And the cursor is displayed in

the unit address display position.

GROUP

SELECT

Press the

switch to display the address number of the in-

terlocked OA processor unit or LOSSNAY that the setting will be perf-

omed on.

-29-

Used the numeric keypad switch to set the address of the indoor unit

that operates with displayed interlocked OA processing unit or LOSSNAY.

When the indoor unit which address is 012.

1) Input "0"

2) Input "1"

3) Input "2"

4) Press the

012

switch 012

*It is also possible just enter "1" "2" .

Before pressing switch, continue to input the data. After pressing

switch, move the cursor to the address to be deleted and press

DEL.

the

switch to delete these addresses.

Set all the indoor units that operate with displayed interlocked OA

processing unit or LOSSNAY.

Repeat operation to to set the indoor units of all interlocked op-

eration units managed by this controller.

BACK

SCREEN

When all settings are completed, press the

switch.

Initial setting screen is displayed.

This ends the interlocked operation setting.

When the interlocked operation settings are performed, refer to section

"5-5 Interlocked operation setting" .

When the group name settings are performed, refer to section "5-6 group

name setting" .

When the user setting are performed, refer to section "5-7 user setting" .

Simultaneously press the

and

keys on the initial setting menu screen

for 2 seconds to complete user operation.After the initial setting processing

is completed (The initial setting screen will be displayed), refer to section

"4 User operation ( page 10 )" and perform user operation.

When this unit is set to slave system controller by No.2 function select, interlocked operation settings can-

not be adjusted. However monitoring of the contents of the interlocked operation settings is possible.

NOTE:

-30-

5 - 6 Group name setting

( 1 ) Setting method

• Specify new group name.

• Either alphabet, numeric characters, hyphens or spaces can be used for name setting.

• Maximum of ten characters can be set.

• When the group name is displayed on the operation monitor screen, the first three characters of the group name

are displayed.

1 Press the

(or

)switch to select"1. GROUP SETTING"

(or"4. GROUP SETTING") of the initial setting menu.

The group configuration setting screen is displayed.

GROUP

Press the

switch to display the group number which will

SELECT

be set in the group name setting.

ENTER

Press the

switch one time.

The group name setting screen is displayed.

The character " " is displayed in reverse.

Press the

switch to move the cursor to the de-

sired character.

ENTER

Press the

switch.

The selected character is displayed in the group name display area.

Repeat operation or and set the group name.

When incorrect character is set, refer to section "Group name correc-

tion method (page 32)" .

Group name display area

-31-

BACK

SCREEN

When the group name setting is completed, press the

switch.

The group configuration setting screen is displayed.

Repeat operation to and perform the group name setting for

each group.

BACK

SCREEN

11 When all the group name settings are complete, press the

switch.

12 The initial setting menu screen is displayed.

To perform the setting, refer to section "5-6 User setting (page

34)".

Simultaneously press the

and

keys on the initial setting menu

screen for 2 seconds to complete user operation.

Next refer to section " 4 User operation " and perform user operation.

When performing corrections to the group name, move the group name

cursor to the character to be correct.

Group name cursor movement method

Move the cursor to one of the group name cursor movement mark

using the

switch.

• Deletion methods

Move the group name cursor to the character to deleted and press

DEL.

the

switch to delete the character.

Group name cursor

Group name cursor movement mark

• Insertion methods

Move the group name cursor to the location where character is to be

INS.

insert and press the

switch to enter desired space.

-32-

( 2 ) Group name copy

• A certain group name can be copied to another group.

( This method use the "M" (memory) and "MR" (memory read) functions.)

• It is convenient to use a group name for other groups because a group name that was copied can also be cor-

rected.

GROUP

SELECT

Press the

switch to display the original group on the group

switch to move the cursor to "M" .

name setting screen.

Press the

ENTER

Press the

switch one time to record the setting name in memory.

"M" is displayed in reverse with blinking.

Recording the setting name to memory is completed.

GROUP

SELECT

Press the

switch to select the copy destination group.

Press the

switch to move the cursor "MR" .

switch to read in memory.

ENTER

Preformed the memory read for the group name.

Refer to section " (1) setting method (page 31)" and perform the cor-

rection of the group name.

-33-

5-7 User setting

• To match the needs for the user this menu is to specify some of the indications and functions that appear on

the user operating screen.

Press the

switch to select "5 USER SETTING" on the initial

setting menu screen.

The user setting screen is displayed.

Press the

switch to select the items to be set.

BACK

SCREEN

When all the selection are completed,press the

to the initial setting menu screen.

switch to return

TEMP. UNIT ˚C / ˚F

Setup condition before delivery from the shop

Item 1. Operation monitor screen display settings

"GROUP NO."

: Groups are indicated by group number on the operation monitor screen.

"NAME"

: Groups are indicated by their first three characters of the group name on the

operation monitor screen.

"UNIT ADDRESS" : Individual units are indicated by their unit address on the operation monitor

screen.

Item 2. Setting the set-back value and the setting temperature used in conjunction with schedule operation.

The set-back value or the setting temperature setting are possible when operation is linked with the

schedule operation.

•

"SET-BACK"

"SET TEMP"

"NONE"

: Allows setting set-back value used in conjunction with ON/OFF patterns during

schedule operation.

: Allows setting of the setting temperature used in conjunction with ON/OFF pat-

terns during schedule operation.

: The schedule operation is only performs normal ON/OFF patterns.

Item 3. Setting filter sign indication

"INDICATE"

"NONE"

: Allows the indication of filter sign.

: Filter sign is not indicated.

Item 4. Group number display

"INDICATE"

: Enable display of group number on the operation setting screen and the schedule

setting screen.

"NONE"

: Group number is not indicated.

Item 5. Change to the sequence of current time

"2001-1-1"

: Current time indicate in a sequence of year,month and date on the current time

setting screen.

"1-1-2001"

: Current time indicate in a sequence of date,month and year on the current time

setting screen.

Item 6. Room temperature indication

"INDICATE"

"NONE"

: Indicated every each group

: Not indicated every each group

Item 7. Temperature unit

: Setting Centigrade

: Setting Fahrenheit

-34-

5-8 IP address setting

• This function allows setting of the IP address and mask address needed at LAN connection.

WED 15:29

1 Select the

switch select "8. IP ADDRESS SETTING"

on the initial setting menu screen.

ADDRESS SETTING

FUNCTION SETTING

IP ADDRESS SETTING

BACK

IP ADDRESS SETTING

IP ADDRESS :

The IP address setting screen appears.

Move the cursor to the address setting position by pressing the

and keys.

192.168.001.001

MASK ADDRESS :

255.255.255.000

Set the address with the 0 to 9 numeric switches.

When all address setting are complete, return to the initial

BACK

SCREEN

setting menu screen by pressing

switch.

5-9 Initial setting tool connection function

• This function connects the initial setting tool PC by LAN.

• Group setting, interlocked setting, and other information can be downloaded to this unit by using the initial setting tool

Refer to the initial setting tool manual for an explanation of the initial setting tool functions and operating procedures.

LAN changeover switch

ACT

1 Remove the cover from the controller by inserting a flat blade

screwdriver into the gap between the cover and body and twi-

LINK

sting the screwdriver.

2 Use the dedicated cable (sold separately) to connect the initial

setting tool PC to the service LAN connector.

3 When changed to FRONT with the LAN changeover switch,

the initial setting tool PC is connected to the service LAN

Service LAN connector

FRONT

REAR

connector.

4 When setting with the initial setting tool is complete, return the

LAN changeover switch to the REAR position.

*When a service LAN connector is used, the option Model

PAC-YG00FA-E is necessary.

-35-

6. Maintenance

6-1 Refrigerant system monitor

• This function allows monitoring of the address of the outdoor units, and BC controller connected to the refrig-

erant system. It is useful for checking address settings, transmission line connection during installation.

Press the

switch to select "3 REFRIGERANT MONITOR" on

the initial setting menu screen.

The process for monitoring of the refrigerant system is executed.

Please wait.

The refrigerant system monitor screen of the lowest outdoor unit address

is displayed.

GROUP

SELECT

Press the

switch to change the displayed refrigerant system.

BACK

SCREEN

When the monitoring is end, press the

setting menu screen.

switch to back to the initial

-36-

6-2 Malfunction log monitor

• This function allows monitoring of a log of the last 64 malfunctions.

• The contents of malfunction and time the malfunction occurred is displayed. The contents of malfunction

is the address of the unit where it occurred, the error code and the address of the unit that detected the

malfunction.

• This data are remains in the memory even if supplied power is cut off.

• The malfunction log data can be deleted using the malfunction log reset operation. If the malfunction log data

is reset after the system is serviced, the log will provide a convenient record of the malfunction that have

occurred after that time when the system is next serviced.

Press the

switch to select "4 MALFUNCTION MONITOR" on

the initial setting menu screen.

The malfunction log monitor screen is displayed.

Changing pages on the malfunction log monitor screen.

2002

16-04-2002

2002

05-04-2002

2002

GROUP

SELECT

Each time this switch is pressed, the current page

+1 is displayed.

(

)

GROUP

SELECT

Each time this switch is pressed, the current page

-1 is displayed.

Malfunction log reset operation

RESET

Press the

DEL.

switch to clear the malfunction log.

-37-

7.External input/output function

* External signal input requires the external I/O adapter (Model : PAC-YG10HA-E) sold separately.

7-1 External input function

(1) The function of external input

• Emergency stop/normal operation, ON/OFF, local remote control prohibit/permit can be controlled for all air

conditioners being controlled with a non-voltage contact signal input from an external input source. (Select with

the dip switches)

• The condition of external input signal is displayed on the operation setting screen for each group.

Function

Remarks

No.

Function of external input signal

External input signal not used

No.6 No.7

OFF OFF

During emergency stop, only ON/OFF of the central

controller and local remote controller's operation

will be prohibit.

Perform emergency stop with level signal

OFF ON

ON OFF

Only the ON/OFF operation of the central controller

and the local remote controller will be prohibit.

Perform ON/OFF operation with level sig-

nal

Perform ON/OFF operation,prohibit/per-

mit operation with pulse signal

Set the pulse width while the contact is ON to 0.5

to 1.0 second.

(2) Level signal and pulse signal

Level signal

Pulse signal

(3) Specification of external input interface

ON/OFF , prohibit/premit

pulse signal

Emergency stop/normal

CN2 Lead wire

ON/OFF level signal

level signal

No.5

No.6

Orange

Yellow

Emergency stop/normal input

Not used

ON/OFF input

Not used

ON input

OFF input

Local remote controller

prohibit input

No.7

Blue

Not used

Local remote controller

permit input

No.8

No.9

Gray

Red

Not used

Common(DC12V or DC24V)

(A) Level signal

When the level signal is selected, the operation (only ON/OFF operation) for the central controller and the

local remote controller are prohibited (except during normal operation).

When the emergency stop/normal operation signal is selected, the status will be changed from normal oper-

ation to emergency stop when the external input signal contact turns OFF to ON, and will be changed from

emergency stop to normal operation when external input signal contact turns ON to OFF.

When ON/OFF input signal is selected, the status will be changed from OFF to ON when the external input

signal contact turns OFF to ON, and will be changed from ON to OFF when the external input signal contact

turns ON to OFF.

-38-

(B) Pulse signal

Even if the ON signal is input during ON, the status will remain at the ON status.

When the local remote controller is prohibited, the ON/OFF operation, operation mode selection and

temperature setting from the local remote controller is prohibited.

Set the pulse width (contact ON time) to 0.5 to 1.0 second.

7-2 External output function

(1)The function of external output

•The "ON" signal is output when one or more air conditioner are in the ON operation.

•The "Malfunction" signal is output when one or more air conditioner malfunctions.

(2)Specification of external output interface

CN2

No.1

No.2

No.3

Lead wire

Green

Description of each terminal

Common (0V)

Black

ON/OFF

Brown

Malfunction/Normal

1 "ON" signal and "Malfunction" signal will both be output.

-39-

Appendix 1 : Initial setting (abridged)

Initial setting list

Power on

Displaying for a maximum of 7 minutes.

* User operation

WED 15:29

1 OPERATION MONITOR

2 OPERATION SETTING

3 SCHEDULE SETTING

4 MALFUNCTION

There is group

information.

INITIAL SETTING

MONITOR

5 CURRENT TIME

PLEASE WAIT

SETTING

Group information

modification and

settings modification

Continously press

and

There is no group

information.

(2 seconds or longer)

WED 15:29

1 GROUP SETTING

ADDRESS SETTING

FUNCTION SELECT

IP ADDRESS SETTING

GROUP SETTING

2 INTERLOCKED

SETTING

3 REFRIGIERANT

MONITOR

Setting end

4 MALFUNCTUON

MONITOR

5 USER SETTING

PLEASE SET

INITIAL SETTING

ENTER

WED 15:29

ADDRESS SETTING

FUNCTION SETTING

IP ADDRESS SETTING

BACK

SCREEN

VER.

BACK

Setting items

Menu items screen

Group configuration setting

… This performs the same group setting.

GROUP SETTING

G01

ADDRESS

UNIT

GROUP

SELECT

•

: Select the group number.

: Move the cursor to address display position.

: Set the address.

• Numeric keypayed

REMOTE CONTROLLER

SYSTEM CONTROLLER

indoor unit, local remote controller

slave system controller

GROUP NAME SET

BACK

SCREEN

ENTER

GROUP NAME

G01

•

: Move the cursor to the desired character.

ENTER

•

: Select the charactor.

: Delete the charactor.

DEL.

1 2 3 4 5 6 7 8 9 0

•

A B C D E F G H I J K L M

N OP Q R S T U V

Group name display area

-40-

Interlocked setting

INTERLOCKED SETTING

… Registration of interlocked operation of ventilation unit with single or

INTERLOCKED

UNIT ADDRESS

multiple indoor unit is performed.

005

GROUP

SELECT

•

: Select the address number of the interlocked

OA processor unit or LOSSNAY.

UNIT ADDRESS

•

: Move the cursor to address display position.

: Set the address of the indoor unit.

• Numeric keypayed

User setting

… Select the display method and timer settings.

: Select the items.

USER SETTING

OPERATION MONITOR

GROUP NO. /NAME

/UNIT ADDRESS

•

SCHEDULE DATA

SET- BACK/SET TEMP

/ NONE

FILTER SIGN

NONE/INDICATE

GROUP NO. DISPLAY

NONE/INDICATE

2001-1-1/1-1-2001

ROOM TEMPERATURE

NONE/INDICATE

TEMP. UNIT ˚C / ˚F

Refrigerant monitor

REFRIGERANT MONITOR

… The unit address are displayed for each refrigerant system.

O U T D O O R A D D R E S S

5 1

5 2

GROUP

SELECT

•

: Change the displayed refrigerant system.

B C / O S

U N I T

A D D R E S S

0 1

0 8

1 5

0 2

0 9

1 6

0 3

1 0

0 4

1 1

0 5

1 2

0 6

1 3

0 7

1 4

Malfunction log

… The function allows monitoring of a log of the last 64 malfunction.

MALFUNCTION LOG

PAGE 01/01

GROUP

18-04-2002

19:01

•

: Changing pages.

SELECT

001-6607 (DETECT 000)

16-04-2002

12:45

014-6602 (DETECT 014)

12-04-2002

03:23

003-6607 (DETECT 000)

15-04-2002

09:12

112-6607 (DETECT 012)

01-04-2002

23:56

001-6607 (DETECT 000)

DEL.

: Clear the malfunction log.

M-NET address setting

M-NET ADDRESS

… Displays, or sets, the controller M-NET address.

• Numeric keypayed : Set the controller address.

M-NET ADDRESS: 000

(000,201 250)

*Initial value is 000.

Function setting

FUNCTION SETTING

… Sets the function of the controller.

• Numeric keypayed : Set ON/OFF

: Active

•

: Move the cursor.

OFF

When No.3 is set to ON, the KA address input field is displayed.

Numeric keypayed : Set the address of the K transmission conveter.

IP address setting

IP ADDRESS SETTING

… Sets the LAN IP address.

*Setting is unnecessary when a LAN is used.

IP ADDRESS :

192.168.001.001

•

: Move the cursor to the address setting position.

: Set the address (0 255)

MASK ADDRESS :

255.255.255.000

• Numeric keypayed

-41-

Appendix 2 : User operation (abridged)

Shows the operation panel, screen, etc. for user operation.

Overall status lamp

Collective operation switch

OFF

…During operation

…All group are stopping

BLINKING…Malfunction

ON/OFF

TEST RUN

ON/OFF MODE

FAN SPEED

GROUP

SELECT

AIR

DIRECTION

BACK

SCREEN

CLOCK/

TEMP.

PATTERN

VENTILATION

INS.

REMOTE

TIMER

MODE

PROHIBITION

RESET

DEL.

CENTRAL CONTROLLER

G-50A

ENTER

User operation menu screen

WED 15:29

1 OPERATION MONITOR

Initial setting

2 OPERATION SETTING

3 SCHEDULE SETTING

Continously press

and

* To initial setting

( 2 seconds or longer )

4 MALFUNCTION

MONITOR

5 CURRENT TIME

SETTING

BACK

SCREEN

Operation setting screen

*The following settings are possible using the

Operation Panel switches

• Start/Stop, mode, set temperature, etc.

• Local remote control operation prohibition setting

Function area

MON. : MONITOR

PROH. : PROHIBIT

COL. : COLLECTIVE

MR.

: MEMORY

: MEMORY READ

BACK

SCREEN

BACK

SCREEN

Reverse : ON

Normal : OFF

Blinking : Malfunction during unit off

Blinking and Reverse : Malfunction during unit is on

Blinking "MON."

BACK

Operation monitor screen

SCREEN

GROUP

SELECT

•

: Change the display group

: Turn all the units in that group ON or OFF

ON/OFF

•

: Move the " " symbol.

ON/OFF

•

: Set the displayed group unit in indicated by the " " symbol

to the ON/OFF mode.

-42-

Weekly schedule setting screen

GROUP

SELECT

•

: Change the display group.

: Move the cursor to the pattern position.

CLOCK / PATTERN

•

: Select P1 to P4 or ( - )

ENTER

: Complete the setting.

The cursor will move to the next setting position.

* Repeat assign the schedule pattern to each day (and each group)

NOTE :

When the No.4 function select is set ON, P4 connot be set.

BACK

SCREEN

* P1 to P3 of a composite pattern composed of P1 to P3 and P4.

P1 P4

BACK

SCREEN

ENTER

•

: Move the cursor position.

CLOCK / PATTERN

: Select the ON(PROHIBITION) time or OFF

(PERMISSION) time.

(Time is changed by 10 minutes unit.)

ENTER

•

: Complete the setting. The cursor moves to the next setting p

* Repeat set schedules.

* Three types (P1-P3) of daily ON/OFF pattern and one type (P4) of prohibition/

permission pattern are available respectively, each of which can be set for each

group.

Schedule parttern setting screen

Malfunction monitor screen

BACK

SCREEN

•

: Change the pages

= page + 1

= page - 1

RESET

DEL.

: Reset all malfunctions

The unit address

where the malfunction occurred

The unit address

where the malfunction was detected

Error code

NOTE :

When there is no malfunction taking place,[NO ERROR] lights up instead of [ERROR CODE].

When operation of the G-50A is prohibited,reset operation is invalid.

BACK

SCREEN

Current time setting screen

•

: Move the cursor position

: Set the number or day

* Set the date day, month, year and time.

ENTER

•

: Press this switch, where all setting have been completed.

22-09-2002 SUN 00:00

* The clock count will start with the second reset to 0.

-43-

This product is designed and intended for use in the residential,

commercial and light -industrial environment.

The product at hand is

based on the following

EU regulations:

• Low Voltage Directive 73/23/EEC

• Electromagnetic Compatibility Directive 89/

336/EEC

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide resonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications.

However, there is no quarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio / TV technician for help.

MITSUBISHI ELECTRIC CORPORATION

HEAD OFFICE: MITSUBISHI DENKI BLDG. , 2-2-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

WT03945X01

Printed in Japan

Recycled Paper

Panasonic Cu 2c24dku User Manual
Riccar Summer Breeze Rsbh Sb User Manual
Ricoh Aficio Mp 1100 User Manual
Samsung Aw07ph Series User Manual
Samsung Scx 5530fn User Manual
Sanyo 24ks32a User Manual
Sanyo Dc Inverter Split System Xhs1271 User Manual
Sears Automobile Parts 8755019 User Manual
Sharp Mx De11 User Manual
York 13 User Manual