LaserPrinter 4039 Series
4039-1XX
• Table of Contents
• Start Diagnostics
• Safety and Notices
• Trademarks
• Index
• Manuals Menu
Lexmark is a trademark of Lexmark
International, Inc., registered in the
United States and/or other countries.
4039-1XX
Table of Contents
Electronic Emission Notices............................................................. ix
Federal Communications Commission (FCC) Statement ............ ix
European Community (EC) Electromagnetic Compatibility
Directive ....................................................................................... xi
Maintenance Approach .................................................................3
Diagnostic Information............................................................. 5
4039 Diagnostics: Failures With Error Codes ...................................5
Power-On Self Test (POST)............................................................11
Table of Contents iii
4039-1XX
Operator Panel Problem..............................................................24
Paper Feed Problem, 500-Sheet Second Tray ...........................25
Skew, all edges ...........................................................................30
Skew, top and bottom only..........................................................30
Stalled (diamonds on display) .....................................................30
Vertical Void or Streak.................................................................31
iv Service Manual
4039-1XX
Print Test 3...........................................................................44
Quick Disk Test...........................................................................44
Quick Test...................................................................................44
Sensor Test.................................................................................45
Table of Contents v
4039-1XX
LAN Information ..........................................................................47
Adjustments.....................................................................................52
Envelope Restraint Spring On The Envelope+ Feeder ...............52
Printhead Skew - Level 1 ............................................................59
Input Sensor Removal.................................................................80
Lower Frame Assembly Removal ...............................................81
LVPS Removal............................................................................82
LVPS Cover Removal .................................................................83
vi Service Manual
4039-1XX
Upper Frame Removal................................................................95
Zif Connector Removal ...............................................................96
Duplex Option Bottom Cover And
System Board Connectors 16L .................................................108
System Board Connectors 10P.................................................110
Printhead Cables.......................................................................112
Mirror Motor Cable/Fan Cable...................................................113
Handle-Mounted Outbin Sensor................................................114
Operator Panel/Output Bin Sensor Cable —
Redrive-Mounted Outbin Sensor...............................................115
Printer Ground Straps ...............................................................117
Table of Contents vii
4039-1XX
Printhead Window Cleaning Procedure ....................................122
Assembly 12: Fuser ...........................................................155
Assembly 13: Electronics...................................................159
Auxiliary Feeder ............................................................167
Assembly 17: Options ........................................................169
Assembly 18: Miscellaneous..............................................170
Index ...................................................................................... 171
viii Service Manual
4039-1XX
Notices and Safety Information
References in this publication to products, programs, or services do
not imply that the manufacturer intends to make these available in all
countries in which it operates. Any reference to a product, program,
or service is not intended to state or imply that only that product,
program, or service may be used. Any functionally equivalent
product, program, or service that does not infringe any existing
intellectual property rights may be used instead. Evaluation and
verification of operation in conjunction with other products,
programs, or services, except those expressly designated by the
manufacturer, are the user’s responsibility.
Electronic Emission Notices
Consult the following list for any emission that may apply in your
country.
Federal Communications Commission (FCC) Statement
This printer has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult your point of purchase or service representative for
additional suggestions.
Notices and Safety Information ix
4039-1XX
The manufacturer is not responsible for any radio or television
interference caused by using other than recommended cables or by
unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user’s
authority to operate the equipment.
Note: To comply with FCC regulations on electromagnetic interfer-
ence, for a Class B computing device, the printer cable must be
shielded.
To assure compliance with FCC regulations for a Class B computing
device, use a properly shielded and grounded IBM cable. Part
numbers for the various interface cables are: part number 1525612
for parallel interface, and part number 8509386 for serial interface.
Use of a substitute cable not properly shielded and grounded may
result in violation of FCC regulations.
Industry Canada Compliance Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the interference-
causing equipment standard entitled: “Digital Apparatus”, ICES-003
of Industry Canada.
Avis de conformité aux normes d’Industrie Canada
Cet appareil numérique respecte les limites de bruits
radioélectriques applicables aux appareils numériques de Classe B
prescrites dans la norme sur le matériel brouilleur : “Appareils
numériques”, NMB-003 édictée par Industrie Canada.
The United Kingdom Telecommunications Act 1984
This apparatus is approved under the approval number NS/G/1234/
J/100003 for the indirect connections to the public
telecommunications systems in the United Kingdom.
x Service Manual
4039-1XX
European Community (EC) Electromagnetic
Compatibility Directive
This product is in conformity with the protection requirements of EC
Council directive 89/336/EEC on the approximation of the laws of
the Member States relating to electromagnetic compatibility.
German Statement of Acoustic Emissions
A declaration of conformity with the requirements of the Directive
has been signed by the Director of Manufacturing and Technical
Support, Lexmark International, Ltd., Boigny, France.
This product satisfies the Class B limits of EN 55022.
Notices and Safety Information xi
4039-1XX
Safety Information
•
The maintenance information for this product has been prepared
for use by a professional service person and is not intended to
be used by others.
•
There may be an increased risk of electric shock and personal
injury during disassembly and servicing of this product.
Professional service personnel should understand this and take
necessary precautions.
•
The safety features of some parts may not always be obvious.
Therefore, replacement parts must have the identical or
equivalent characteristics as the original parts.
Sicherheitshinweise
•
Die Wartungsinformationen für dieses Produkt wurden zur
Verwendung durch einen Wartungsfachmann entwickelt und
sollten nicht von anderen benützt werden.
•
Zusätzliches Risiko eines elektrischen Schlags und körperlicher
Verletzung existiert während des Auseinandernehmens und der
Wartung des Geräts. Fachpersonal sollte im vollen Verständnis
der Lage entsprechende Vorsichtsmaßnahmen ergreifen.
•
Ersatzteile müssen gleiche oder gleichwertige Merkmale wie die
Originalteile aufweisen, da Sicherheitsvorkehrungen nicht immer
offensichtlich sind.
Consignes de Sécurité
•
•
•
Les consignes d'entretien et de réparation de ce produit
s'adressent uniquement à un personnel de maintenance
qualifié.
Le démontage et l'entretien de ce produit pouvant présenter
certains risques électriques, le personnel d'entretien qualifié
devra prendre toutes les précautions nécessaires.
Les normes de sécurité de certaines pièces n'étant pas toujours
explicites, les pièces de rechange doivent être identiques ou
conformes aux caractéristiques des pièces d'origine.
xii Service Manual
4039-1XX
Norme di sicurezza
•
Le informazioni riguardanti la manutenzione di questo prodotto
sono indirizzate soltanto al personale dell'assistenza
autorizzato.
•
Durante lo smontaggio e il manutenzionamento di questo
prodotto, è possibile il rischio accresciuto di scosse elettriche e
danni personali. Il personale di assistenza autorizzato,
consapevole di ciò, deve adottare le precauzioni necessarie.
•
È possibile che le funzioni di sicurezza di alcuni elementi non
siano così ovvie, quindi, i pezzi di ricambio devono avere
caratteristiche identiche o equivalenti a quelle dei pezzi originali.
Pautas de Seguridad
•
La información sobre el mantenimiento de este producto fue
escrita para el personal de mantenimiento cualificado y no para
cualquier otro usuario.
•
Existen mayores riesgos de descargas eléctricas y daños
personales durante el desmontaje y la reparación de la
máquina. El personal cualificado comprende esto y toma las
precauciones necesarias.
•
Los dispositivos de seguridad de algunas partes quizá no
siempre puedan ser reconocidas a simple vista. Por lo tanto, las
partes de reemplazo deben poseer características idénticas o
equivalentes a las partes originales.
Sikkerhedsoplysninger
•
•
•
Oplysningerne om vedligeholdelse af dette produkt er forberedt
med henblik på professionelt servicepersonale, og bør derfor
ikke benyttes af andre.
Risikoen for elektrisk stød øges under demontering og service af
dette produkt, hvorfor der bør tages de nødvendige
forholdsregler.
Sikkerhedsforanstaltningerne er ikke altid lige åpenbare for alle
reservedele. Der bør derfor kun anvendes originale reservedele
eller reservedele med samme egenskaber som de oprindelige.
Ozone Information
This product does not produce measurable amounts of ozone gas.
Notices and Safety Information xiii
4039-1XX
Preface
This manual is divided into the following chapters:
•
•
“General Information” contains a general description of the
printer and the maintenance approach used to repair it. Special
tools and test equipment are listed in this chapter, as well as
general environmental and safety instructions.
“Diagnostic Information” contains error code table, symptom
table, and service checks used to isolate failing field replaceable
units (FRUs).
•
•
•
“Diagnostic Aids” contains tests and checks used to locate or
repeat symptoms of printer problems.
“Repair Information” provides instructions for making printer
adjustments and removing and installing FRUs.
“Connector Locations” uses illustrations to identify the major
components and test points on the printer.
• “Preventive Maintenance” contains safety inspection guidelines,
lubrication specifications, and maintenance information to
prevent problems and maintain optimum performance.
•
“Parts Catalog” contains illustrations and part numbers for
individual FRUs.
xiv Service Manual
4039-1XX
General Information
The 4039 is a family of 600 dpi Laserprinters designed to attach to
IBM-compatible PC’s and to most types of computer networks. The
printer has PostScript and PCL emulation standard.
Models Covered in this Manual
There are no voltage or pinout differences between the regular
models and the plus models. For example, a voltage callout for the
16L also applies to the 16L plus.
IBM Models
4039-10R
4039-12R
4039-12L
4039-12C
4039-16L
10ppm PostScript Level 1 emulation, input/output
capacity 200/250
12ppm PostScript Level 1 emulation, input/output
capacity 200/250
12ppm PostScript Level 1 emulation, output bin
sensing, input/output capacity 500/500
Similar to 12R, designed for printing labels and card
stock
16ppm PostScript Level 1 emulation, output bin
sensing, input/output capacity 500/500
4039-10R plus 10R with PostScript Level 2 emulation and service
error log (RPQ only)
4039-12R plus 12R with PostScript Level 2 emulation and service
error log
4039-12C plus 12C with PostScript Level 2 emulation and service
error log (RPQ only)
4039-12L plus 12L with PostScript Level 2 emulation and service
error log
4039-16L plus 16L with PostScript Level 2 emulation and service
error log
General Information 1
4039-1XX
Lexmark Model
4039-10 plus (Called 10P in this manual and on the serial number
plate) 10ppm, PostScript Level 2 emulation, no
serial port, torquer motor rather than paper pick
solenoid, and service error log
Options
The following options are available. Some options are not
compatible with all printer models. Some options are not available in
every country. Contact your point of purchase for options available in
your country.
Memory upgrade options of 2MB, 4MB and 8MB.
Flash memory options of 1MB, 2MB and 4MB
Intergated network options
Token-Ring option
Ethernet option
AppleTalk option
200 and 500-sheet paper trays of A5, letter, and legal size.
500-sheet second drawer (withe letter-size paper tray)
Envelope+ feeder
100-sheet auxiliary
Duplex option
Font cards
Font cards adapter
40 MB Hard Disk
Serial adapter
2 Service Manual
4039-1XX
Maintenance Approach
The diagnostic information in this manual will lead you to the correct
field replaceable unit (FRU) or part. Use the error code charts,
symptom index, service checks, and diagnostic aids to determine
the symptom and repair the failure. See “Diagnostic Information”
starting on page 5. This printer can be serviced without being
connected to a host.
After you complete the repair, perform tests as needed to verify the
repair.
General Information 3
4039-1XX
Abbreviations
ASIC
CSU
Application-Specific Integrated Circuit
Customer Setup
DRAM
EEPROM
Dynamic Random Access Memory
Electrically Erasable Programmable Read-
Only Memory
EP
ESD
FRU
Electrophotographic Process
Electrostatic Discharge
Field Replaceable Unit
HVPS
LAN
High Voltage Power Supply
Local Area Network
LASER
Light Amplification by Stimulated Emission
of Radiation
LCD
Liquid Crystal Display
LED
Light-Emitting Diode
LVPS
NVRAM
OEM
PICS
PIXEL
POR
POST
PQET
RIP
Low Voltage Power Supply
Nonvolatile Random Access Memory
Original Equipment Manufacturer
Problem Isolation Charts
Picture Element
Power-On Reset
Power-On Self Test
Print Quality Enhancement Technology
Raster Image Processor
Read-Only Storage
ROS
SRAM
UPR
VAC
Static Random Access Memory
Used Parts Replacement
Volts alternating current
Volts direct current
VDC
Unique Tools Required For Service
Wrap Plug (Parallel), P/N 1319128
Wrap Plug (Serial), P/N 1329048
Twinax/serial debug cable, P/N 1381963
Coax/serial debug cable, P/N 1381964
4 Service Manual
4039-1XX
Diagnostic Information
4039 Diagnostics: Failures With Error Codes
Two-digit codes are messages for the 4039 user, but if they recur
frequently or at inappropriate times they may be symptomatic of a
service problem. On “plus” models, refer to the diagnostics error log
for the last six errors or paper jam codes.
Error/Code
Action
20 Paper Jam
The input sensor was not unmade in
page 25.
21 Paper Jam
22 Paper Jam
23 Paper Jam
The exit sensor was not made in time
“Paper Feed, Base Printer” on page 25.
The exit sensor was not unmade in time.
See “Paper Feed, Base Printer” on
page 25.
Jam at the duplex unit. Paper is either
not leaving the duplex entry sensor in
time or not making or unmaking the
duplex exit sensor in time. See “Duplex”
on page 18.
24 Short Paper
The defined paper size is too short to
print data as formatted.
25 Incorrect Manual Feed
Paper fed manually while motor is
running and previous page in path.
27 Change Envelope/Paper
28 Load Envelope/Paper
Envelopes/paper loaded are wrong size.
Input sensor not made after pick
attempt. Tray is empty or printer is
requesting a manual feed.
29 Output Bin Full
The output bin sensor has not been
unmade.
30 Top Cover Open or Print Cartridge
Missing
Diagnostic Information 5
4039-1XX
Error/Code
Action
37 Insufficient Memory
Not enough memory for function
requested.To verify that the printer
recognizes all the installed memory, go
to the user menus and print the “Print
Menus” test page. Make sure the
memory shown on the printout matches
the installed memory.
38 Memory Full
Memory used to store pages is full.To
verify that the printer recognizes all the
installed memory, go to the user menus
and print the “Print Menus” test page.
Make sure the memory shown on the
printout matches the installed memory.
39 Complex Page
Page too complex to print.To verify that
the printer recognizes all the installed
memory, go to the user menus and print
the “Print Menus” test page. Make sure
the memory shown on the printout
matches the installed memory.
43 Font Card Not Supported
Font card format not supported by
printer.
44 Defective Font Card
47 Font Card Removed While Printing
52 Flash Full
Defective font card installed in font slot.
Printer needs data on removed card.
Not enough flash memory for data
requested to be stored.
53 Unformatted or Defective Flash
Flash problem at POR or while
attempting to write.
54 Serial Error
Framing or parity error on serial.
58 Duplex Not Attached
Duplex is electrically connected but no
longer mechanically attached, and
printer top cover is closed.
59 Duplex Cover Open
62 Disk Full
Top cover of duplex unit is sensed open.
Not enough disk space for data that has
been requested to be written to disk.
6 Service Manual
4039-1XX
Error/Code
Action
63 Unformatted or Defective Disk
The printer will ignore a disk it senses as
defective. Run the Quick Disk Test. If the
test fails, the disk is defective or the data
on track1 is bad. If the Quick Disk Test
passes but the disk does not work, run
the Disk Test/Clean (2 hr. test). Replace
the disk if instructed by the operator
panel.
7X Network Card Codes
These user codes are documented in
various network card user manuals. See
“Network Wrap Tests” on page 23.
80 Scheduled Maintenance
Printer has reached 200,000 prints
(12C=100,000 prints) without
maintenance count reset.
88 Toner Low
Toner sensor detects low toner.
90X Software Error
Unrecoverable software error. If one of
these errors appeared during POST, or
while the printer was idle (not printing or
receiving data), or while trying to print
one of the internal test pages, replace
the system board. If the error appeared
while sending a job from the host to the
printer, turn the printer off, then turn it on
and try again. If the error appears again,
call the next level service support for
assistance.
917 Transfer Roll Error
Cannot start servo operation. Verify
correct cable connections from the
Engine board to the HVPS. Make sure
there is continuity between the transfer
roller and its contact on the HVPS;
replace the transfer roll if the continuity
is correct. If there is no continuity, make
sure the HVPS contact returns to its
upward limit when depressed, and make
sure the left bearing of the transfer roll is
making proper contact.
Diagnostic Information 7
4039-1XX
Error/Code
Action
918 Transfer Roll Error
Servo Failure. Verify correct cable
connections from the Engine board to
the HVPS. Make sure there is continuity
between the transfer roller and its
contact on the HVPS; replace the
transfer roll if the continuity is correct. If
there is no continuity, make sure the
HVPS contact returns to its upward limit
when depressed, and make sure the left
proper contact.
920 Fuser Error
921 Fuser Error
922 Fuser Error
923 Fuser Error
Fuser is below temperature while
Error” on page 20.
Fuser is below standby temperature
Error” on page 20.
Fuser failed to reach standby
temperature. See “Fuser: 920, 921, or
Fuser is too hot while printing or when
927 Fan Stalled
931 Printhead Error
No first hsync. See “Printhead” on
page 27.
932 Printhead Error
934 Printhead Error
Lost hsync. See “Printhead” on page 27.
Lost lock condition. See “Printhead” on
page 27.
935 Printhead Error
941 System Board
Mirror motor unable to reach operating
speed. See “Printhead” on page 27.
ROM SIMM failed CRC; code data or
font data. Run the diagnostic Memory
Test for ROM. Replace the SIMM if the
test fails or the problem recurs after
POR; replace the system board if the
SIMM does not fix the problem.
944 System Board
945 System Board
RIP processor failure. Replace the
system board.
ASIC 1 failure. Replace the system
board.
8 Service Manual
4039-1XX
Error/Code
Action
946 System Board
ASIC 2 failure. Replace the system
board.
947 System Board
948 System Board
950 System Board
952 System Board
953 System Board
960 Memory Error
Engine ASIC RAM failure. Replace the
system board.
Engine ASIC electronics failure. Replace
the system board.
SRAM failure. Replace the system
board.
Unable to zero PQET SRAM. Replace
the system board.
NVRAM failure. Replace the system
board.
Bad or missing DRAM in the base
DRAM slot. Reseat the DRAM and run
the diagnostic Memory Test for DRAM. If
test fails or the problem recurs after
POR, replace the DRAM SIMM.
961 Memory Error
Bad DRAM in the optional DRAM slot.
Reseat the DRAM and run the
diagnostic Memory Test for DRAM. If
test fails or the problem recurs after
POR, replace the DRAM SIMM.
970 Network Card
971 Network Card
972 Network Card
973 Network Card
974 Network Card
976 Network Card
Network card processor failure. Replace
the Network Card.
Network card RAM failure. Replace the
Network Card.
Network card ROS/FLASH failure.
Replace the Network Card.
Network card EEPROM/NVRAM failure.
Replace the Network Card.
Network card/Network interface error.
Replace the Network Card.
Network card software error. Verify that
the network card is installed and
grounded correctly. If this error returns
after a POR, there is a software or
microcode incompatibility problem. Do
Not replace the card. Contact your next
level of support.
Diagnostic Information 9
4039-1XX
Error/Code
Action
977 Network Card
Network card is installed but is not
communicating with the system board.
See “Network Card 977 Errors” on
page 23.
978 Network Card
979 Network Card
General network card hardware error.
Replace the Network Card.
General network card software error.
Verify that the network card is installed
and grounded correctly. If this error
returns after a POR, there is a software
or microcode incompatibility problem.
Do Not replace the card. Contact your
next level of support.
990 Duplex Option
Duplex error. See “Duplex” on page 18.
991 Duplex System Card Failure
duplex system card.
993 Duplex Comm. Failure
Communications between the duplex
unit and the printer have failed. See
“Duplex” on page 18.
10 Service Manual
4039-1XX
Power-On Self Test (POST)
When you turn the printer on, it performs a Power-On Self Test.
Check for correct POST functioning by observing the following:
1. 1½ rows of pels appear on the display and then clear.
2. Diamonds fill the display and then clear.
3. The fuser lamp and the fan turn on. [Performing Self Test]
appears on the display.
Note: The printer may be idle for up to 60 seconds as the fuser
warms to operating temperature. Printer idle time is shorter if the
fuser is already warm.
Note: If the duplexer is installed, the duplex drive motor turns on
for about 5 seconds just before the ready screen appears.
4. The ready screen appears on the display.
Note: Diagnostics menu appears if you are in diagnostic mode.
5. The drive motor and the mirror motor start to run. The fan starts
to run at high speed.
6. The drive motor runs for approximately 10 seconds. The fan runs
at high speed, then switches to low speed.
If the printer completes all these steps and no error messages are
displayed, the printer has successfully completed the POST.
Diagnostic Information 11
4039-1XX
Symptom Table
Symptom
Action or Service Check
Dead Machine
Dead Machine Service Check
Operator Panel Service Check
Repeats pattern of five beeps and a
pause.
Machine Hangs Displaying Diamonds
Machine Hangs Displaying Diamonds
Service Check
Operator Panel
Operator Panel Service Check
Paper Feed, Base Printer
Paper Feed, Duplex Unit
Paper Feed, Base Printer Service Check
Paper Feed, Duplex Unit Service Check
Paper Feed Problem, 500-sheet
Second Tray
Paper Feed Problem, 500-sheet Second
Tray Service Check
Paper Feed Problem, Envelope+
Feeder/100-Sheet Auxiliary Feeder
Paper Feed Problem, Envelope+
Feeder/100-Sheet Auxiliary Feeder
Service Check
Automatic Paper Size Sensing Problem
Automatic Paper Size Sensing Problem
Service Check
LAN Problems
LAN Service Check
Blank Page
Blank Page Service Check
Black Page Service Check
Random Marks Service Check
Regularly Spaced Marks Service Check
Skew Service Check
Black Page
Random Marks
Regularly Spaced Marks
Skew, all edges
Skew, top and bottom only
Light Print
Skew, top and bottom Service Check
Light Print Service Check
Fuzzy or Blurred Print
Residual Image
Honeycomb
Fuzzy Blurred Print Service Check
Residual Service Check
Honeycomb Service Check
Background Service Check
Horizontal Service Check
Background
Horizontal Void or Streak
12 Service Manual
4039-1XX
Symptom
Action or Service Check
Vertical Void or Streak
Banding
Vertical Service Check
Banding Service Check
Banding
Banding appears as light and dark horizontal lines on a page that is
supposed to be uniformly gray. It is due to variation in the speed of
the paper as it moves from roll to roll during development or transfer.
It is undetectable when printing text and is most noticeable on fine
dot or horizontal line patterns such as the second page of Print
Test 2 or Print Test 3. Inspect the gear train and the paperfeed rollers
for wear, damage, dirt, or binds.
Background
Areas that are supposed to stay blank are getting small amounts of
toner deposited on them. Clean the erase lamps and the printhead
window.
Run the diagnostic Paper Feed Test and verify that all the erase
lamps turn on. If not, verify that there is +24VDC on pin (10R/12R/
12L/12C) J20-16 (16L) J17-16 (10P) J20-1 and between +15 and
+20VDC on pin 15 (pin 2 on 10P). Shorting pin 15 (pin 2 on 10P) to
ground should turn on all the erase lamps. Check the erase lamp
cable continuity. Replace the transfer roll housing if the voltage and
the cable are good.
Inspect the contacts on the HVPS; make sure each spring-loaded
contact returns when pressed and released.
Rough Paper mode can cause background on some papers; if
Rough Paper mode is on, turn it off and run the print test again.
Printing on coated paper or using refilled print cartridges can also
cause background.
Run the print test in continuous mode and check the following
voltages; then stop the test and check the voltages again:
Diagnostic Information 13
4039-1XX
10R/12R/12C/
12L
Voltage while
Printing
Voltage while
Idling
16L
J20-1 to J20-4
J20-2 to J20-4
J20-3 to J20-4
J17-1 to J17-4
Less than
1VDC
+21-26VDC
J17-2 to J17-4
J17-3 to J17-4
Greater than
1VDC
Less than
5VDC
The meter
should fluctu-
ate slightly
between
Less than
5VDC
each page.
J20-8 to J20-4
J17-8 to J17-4
Less than
1VDC
+21-26VDC
.
Voltage
while Idling
10P
Voltage while Printing
J14-1 to J14-4
J14-2 to J14-4
J14-3 to J14-4
Less than 5VDC
Less than 5VDC
0VDC
0VDC
0VDC
The meter should
fluctuate slightly
between each page.
J14-8 to J14-4
1VDC
6VDC
If any voltages are not correct replace the system board.
Note: “Contrast” on the Diagnostics menu (changed to “Transfer” on
4039 plus machines) does not adjust the print contrast but changes
the transfer algorithm slightly.
Users who run large jobs with very dense graphics in high humidity
environments may get some print quality improvement from
changing this setting; users with more normal jobs will see no
difference.
Make sure the HVPS contacts to the transfer roll housing are in good
condition.
14 Service Manual
4039-1XX
Black Page
Black output is usually caused by an incorrect high voltage in the
printing process, resulting in toner development on the entire
photoconductor drum. Check the condition of each HVPS contact
and make sure they spring back when pressed. Check the continuity
of the HVPS cable. Make sure the following voltages are correct; if
they are not, replace the system board.
10R/12R/12C/
12L
10P
16L
Voltage
J14-5 to J14-4
J14-6 to J14-4
J20-5 to J20-4
J20-6 to J20-4
J17-5 to J17-4
J17-6 to J17-4
+24VDC
+24VDC
Make the following voltage checks while printing and again while
idling. If the voltages are not correct, replace the system board.
10R/12R/12C/
12L
Voltage while
Printing
Voltage while
Idling
16L
J20-1 to J20-4
J17-1 to J17-4
Less than
1VDC
21-26VDC
J20-2 to J20-4
J17-2 to J17-4
Greater than
1VDC
Less than
0.5VDC
Voltage while
Printing
Voltage while
Idling
10P
J14-1 to J14-4
Less than
5VDC
0VDC
J14-2 to J14-4
Less than
5VDC
0VDC
Diagnostic Information 15
4039-1XX
Blank Page
Inspect the printhead shutter for proper operation and make sure the
actuator on top of the cartridge is present and extends into the
printhead shroud when the printer top cover is closed. A failed
printhead will cause a 931 Service error rather than blank output.
Check the continuity of the HVPS cable. The HVPS and transfer roll
contacts should be clean and spring back when pressed. Make sure
the transfer roll contact under the left bearing is making contact with
the HVPS.
Make the following voltage checks while running the print test
continuously and again while idling.
10R/12R/12C/
12L
Voltage while
Printing
Voltage while
Idling
16L
J20-1 to J20-4
J20-2 to J20-4
J20-3 to J20-4
J17-1 to J17-4
Less than
1VDC
+21-26VDC
J17-2 to J17-4
J17-3 to J17-4
Greater than
1VDC
Less than
5VDC
The meter
should fluctu-
ate slightly
between
Less than
5VDC
each page.
J20-8 to J20-4
J17-8 to J17-4
Less than
1VDC
+21-26VDC
16 Service Manual
4039-1XX
.
Voltage while
Printing
Voltage while
Idling
10P
J14-1 to J14-4
J14-2 to J14-4
J14-3 to J14-4
Less than 5VDC
Less than 5VDC
0VDC
0VDC
0VDC
The meter should
fluctuate slightly
between each
page.
J14-8 to J14-4
1VDC
6VDC
If the voltages are not correct replace the system board.
Blurred or Fuzzy Print
This can be caused by a damaged gear train or by paper slippage in
the feed roll or transfer roll. Also see “Banding” on page 13.
Inspect the HVPS contacts; make sure each spring-loaded contact
returns when pressed and released. Inspect the transfer roll housing
contacts for damage or contamination. Check the gear train for
damage, binds, or wear.
When using the 100-sheet auxiliary feeder, some blurring may occur
at the point where the feeder’s friction rollers release the paper.
Dead Machine
Possible causes: no voltage reaching the printer, LVPS failure, blown
LVPS fuse, failure of the On/Off switch or switch linkage, or a
shorted electrical component.
Check for the indicated voltages at the LVPS connection to the
system board. If no voltages are present, remove the LVPS cover
and check fuse F1 and the power switch before replacing the LVPS.
Diagnostic Information 17
4039-1XX
If some voltages are present, but all are not correct, disconnect all
cables except the LVPS from the system board. POR and verify that
the LVPS voltages are correct. Turn the power back off and, one at a
time, reconnect the system board cables, powering on in between
each connection and checking the voltages. The connection which
causes the voltages to be wrong indicates which component is bad.
Repair or replace the failing component or cable as necessary.
Duplex
The duplexer should home — the front shafts should turn and the
input deflector should move — immediately when you install the
duplexer with the printer already powered on, or when you POR the
printer with the duplexer installed. This means the duplexer has
completed its internal tests and is ready to communicate with the
printer.
If the duplexer does not home it is either damaged or is not receiving
+34VDC from the printer.
To check the connection from the printer system board to the duplex
system board, remove the duplex top cover and table cover.
Disconnect the duplex cable from the printer system board. From left
to right (10P: top to bottom), the voltages on the printer system
board connector pins should be 0, +34VDC, 0, +5VDC, 0, and
+5VDC. With the cable connected, these voltages should also be at
duplex system board JP4-1 through JP4-6. If you do not find a cable
or voltage problem, replace the duplex system board.
A 933 error indicates that communication between the printer and
duplexer had been established but has been lost. Check the cable
as above; if the error persists replace the duplex system board.
23 Paper Jams: Examine the paper path in the duplex unit and in
the fuser exit area for paper or other obstructions. Make sure the
duplex unit is positioned correctly on the printer, and that the gear at
the bottom of the duplex unit meshes with the gear on the top of the
paper tray. Check that the paper is fed with no skew or binds from
the duplexer into the metal channel at the right edge of the tray
cover. The tray roller should move the paper forward when the tray
gear is turned, but allow the paper to be pulled by the D-roll when it
picks. Make sure the belt to the duplex DC motor is in place. Make
18 Service Manual
4039-1XX
sure the duplex table cover (floor) is correctly snapped in place at its
front and rear and that the gear block assembly is correctly snapped
into the bottom cover. Run duplex diagnostics tests #1 and #2 to
make sure there is no slippage in the paper path. Make sure the
flags of the duplex unit input and exit sensors move freely.
While the 23 is displayed, press and hold the Return button while
pressing the second button from the top, and note the 7th and 8th
digits from the left. If they are 01 or 03, there is a problem with the
duplex input sensor signal. Remove the duplex top cover and table
cover. Measure the voltage on JP6-3 of the duplex system board; it
should fluctuate from 0 to +5VDC as you toggle the sensor flag.
Check the sensor cable continuity. If the sensor and the cable are
good, replace the duplex system card.
If the 7th and 8th digits are 04, there is an exit sensor problem.
Remove the duplex top cover and table cover. Remove the paper
tray so you can reach the sensor. Measure the voltage on JP6-8 of
the duplex board; it should fluctuate from 0 to +5VDC as you toggle
the sensor. Check the sensor cable continuity. If the sensor and the
cable are good, replace the duplex system card.
Fan (927 Error)
The fan should run continuously when the printer is powered up,
unless the printer is in Power Saver mode. Check that the fan rotates
freely when spun manually and that the cable connections to the fan
are OK. The voltage at (10P/10R/12R/12C/12L) J5-6 (16L) J3-6
should be approximately +24VDC when the top cover is up. Short
pin 6 to ground to test the fan; if the fan does not run check the
continuity of the fan cable before replacing the fan. A bad fan can
pull down the +24V line even if it runs; check that (10P/10R/12R/
12C/12L) J5-7 (16L) J3-7 has between +21 and +26VDC when the
fan is running; if it does not, replace the system board.
Diagnostic Information 19
4039-1XX
Fuser Theory
The fuser lamp operates off line voltage from the LVPS. The
thermistor is in contact with the fuser hot roll. The system board
reads the thermistor resistance and toggles a TRIAC in the LVPS
which cycles the lamp on and off to maintain the proper hot roll
temperature. Inside the fuser shroud there is a thermal fuse which is
in series with the lamp; if the TRIAC fails and leaves the lamp on
continuously, the fuse melts and shuts off power to the lamp.
The thermistor output voltage is proportional to the fuser
temperature and is on (10P/10R/12R/12C/12L) J19-6 (16L) J16-6.
The voltage will cycle from approximately 2.0 to 2.3VDC as the lamp
goes on and off during idle, and will be around 2.7VDC during
continuous printing when the Fuser Temperature is set to Normal. In
Power Saver mode the lamp is left off until a job is printed.
The system board signal to the LVPS TRIAC is on (10P)J11-16
(10R/12R/12C/12L) J11-3 (16L) J18-16. The voltage is 0VDC when
the lamp is to be on and +24VDC (10P: +5VDC) when the lamp is to
be off. The lamp can be tested by briefly connecting this pin to
ground.
Fuser: 920, 921, or 922 Error
A 922 error during a POR caused by low line voltage can usually be
cleared by doing another POR.
If the fuser lamp is lighting very dimly, check for a 220V lamp
installed in a 110V machine.
Check all the connectors to the exit sensor card and the lamp power
connections at the left end of the fuser. Make sure the thermistor is
making contact with the hot roll. Check the continuity of the lamp, the
thermal fuse, and the fuser power cable. Check the thermistor
resistance at (10P/10R/12R/12C/12L) J19-5 to J19-6 (16L) J16-5 to
J16-6; it should be from 100K Ohms to 260K Ohms when cold; it
may be as low as 2.3K Ohms when hot but increases quickly as the
fuser cools. There should be no connection from either pin to
ground.
20 Service Manual
4039-1XX
If the thermal fuse has blown, the fuser and the fuser wiper will be
damaged. Before replacing the fuser and the fuser wiper, check the
voltage at (10P) J11-16 (10R/12R/12C/12L) J11-3 (16L)J18-16 as
you POR again. It should stay at 0 until the 922 Error is displayed
and then go to +24VDC(10P: +5VDC); if it does not, replace the
system board, the fuser, and the fuser wiper. Next, measure the
voltage to the fuser lamp during a POR; it should be line voltage until
the 922 Error is displayed, if it is not, replace the LVPS, the fuser,
and the fuser wiper.
If the voltage to the fuser lamp is the not the same as the line
voltage, replace the LVPS.
If the lamp, fuser power cable, thermal fuse, thermistor and lamp
voltage are OK, check (10P)J11-16 (10R/12R/12C/12L)J11-3
(16L)J18-16 to see if the system board is sending the correct signal
to the TRIAC. At POR this signal should go to +24VDC(10P +5VDC)
and then immediately drop to 0VDC until the fuser is warm; if it does
not, replace the system board. If the signal is OK, replace the LVPS.
Fuser: 923 Error
Check the connection and continuity of the cable from the fuser exit
sensor board to system board (10P/10R/12R/12C/12L)J19
(16L)J16. Check the thermistor condition and connection.
Check the thermistor resistance at system board (10P/10R/12R/
12C/12L)J19-5 to J19-6 (16L)J16-5 to J16-6. It should be from 100K
Ohms to 260K Ohms when cold; it may be as low as 2.3K Ohms
when hot but increase quickly as the fuser cools.
Honeycomb
(Areas of the page are covered with faint 6 mm circles.)
This print defect is usually caused by the print cartridge. If it is not
the problem, verify that the tab on the transfer roll housing is
touching the contact on the HVPS; the transfer roll housing should
have continuity to ground. Make sure the HVPS ground lead to the
side frame is in place and making good contact.
Diagnostic Information 21
4039-1XX
Horizontal Void or Streak
This is usually due to the cartridge not being installed correctly.
Check the printhead area for obstructions, and check the
mechanical workings of the print cartridge and printhead shutter. If
nothing is found go to “Blank Page” and follow those instructions.
LAN Problems
You cannot find a printer or network problem, but jobs still do not
print.
If the network card checks out successfully, the problem may be with
the hardware or software outside of the network card. Below are
some suggestions to the customer for checking hardware and
software for possible problems. Refer the customer to the
LaserPrinter Network Printer Utility Guide to find the problem.
•
Make sure that the desired network protocol is enabled from the
printer operator panel.
•
•
•
•
Verify proper print queue and printer driver configuration
Verify that the adapter port has been associated
Verify correct installation of software utility
Single route broadcast not supported across network bridge, if
bridge is used
•
Server problem; check print server installation and configuration
using the appropriate system guide to operations.
Light Print
Light print is frequently caused by a worn out print cartridge. Clean
the transfer roll by powering on and off two or three times, leaving
the printer on for about two minutes each time. Other causes are the
same as for “Blank Page”.
Make sure Print Darkness on the customer menu is set to Normal or
Dark. 10P: Increasing the diagnostics mode Print Contrast setting
will darken print further.
22 Service Manual
4039-1XX
PostScript emulation output may appear lighter than PCL output or a
test print; this is not a defect. Verify on the Print Test that the print is
too light before performing service.
Network Card 977 Errors
All network card errors are recorded as 977 in the error log. If there
are 977 errors in the log, POR several times and take the
appropriate action for the displayed error code.
If the displayed error is 977, verify that the network card is installed
and grounded correctly. Remove the network card and check for
+5VDC at pin B24 of (10P/10R/12R/12C/12L) J13 (16L) J12. If the
voltage is incorrect replace the system board; if there is +5VDC
replace the network card.
Network Wrap Tests
Token-Ring with Shielded Twisted-Pair Cable: Disconnect the
LAN cable from the electrical outlet, leaving it connected to the
printer network card.
Ethernet 10Base-2: Attach a 50 Ohm BNC terminator cap to each
end of the T-connector. The customer may be able to provide this
cap.
There is no wrap test for Token-Ring with Unshielded Twisted-Pair
cable or for Ethernet 10Base-T.
POR the printer. If the printer completes POR successfully, the
printer, network card, and the port to the LAN are working correctly.
If the customer still has a problem printing, see “LAN Problems” on
page 22.
Output Bin Sensor
Examine the bin area for obstructions or damage. Run the
diagnostic sensor test.
Diagnostic Information 23
4039-1XX
For handle-mounted sensor: The voltage at sensor card J2-3 (pin 1
is the bottom pin) should be +5VDC, and the voltage at J2-4 should
be (12L) 10 to 14VDC (16L) 22 to 26VDC. If these are incorrect and
the cable has continuity, replace the system board. The voltage
between J2-1 and J2-2 should be +5VDC when the light beam is not
blocked, and near zero when it is blocked (the voltage takes 15 to 25
seconds to change to the low level).
For redrive-mounted sensor: make sure the plastic bails and guide
are in good condition and that they guide the sensor flag out of and
into the sensor as paper passes into the bin. On the sensor, the
voltage from pin 2 to pin 3 (pin 1 is the bottom pin) should change
from 0 to +5VDC as the sensor is blocked and unblocked. Pin 1
should always measure +5VDC.
Replace the sensor, the sensor card (on machines with latch-
mounted sensor), or the sensor cable as necessary.
Operator Panel Problem
Possible causes: failed LCD or operator panel card, cable or
connector problem, or system board problem.
Replace the operator panel if POR stops with 1½ rows of pels
displayed.
Run the diagnostic tests for the LCD and for the buttons. If only
some buttons or pels work, replace the operator panel.
If the operator panel is blank: check for +5VDC at pin 1 of the in-line
connector under the top cover, and replace the operator panel if the
voltage is good. Check for +5VDC at (10P/10R/12R/12C/12L) J7-1
(16L) J5-1 on the system board and replace the cable if the voltage
is good.
If the voltage at the system board is incorrect, check that the LVPS is
providing the correct voltages and replace the LVPS if its output
voltages are wrong.
24 Service Manual
4039-1XX
On models 10R/12R/12C/12L, a DC-DC convertor changes
+34VDC at J9-1 into +5VDC, +12VDC, and -12VDC. Check for
+5VDC at J8-1 and for +34VDC at J9-1 and at J11-4. Replace the
DC-DC convertor, the system board, or the LVPS depending on
where the voltage is incorrect.
Paper Feed Problem, 500-Sheet Second Tray
Remove the module and inspect the tray, the module D-roll bias
spring, the gear train, and the paper feed magnet spring. Make sure
the gear train is meshing with the drive gear at the bottom of the
printer. Look for other mechanical problems or damage. Make sure
the cable connector is in good condition. The resistance of the paper
feed magnet should be 100 Ohms to 250 Ohms. If paper is not
feeding correctly check the magnet adjustment.
Paper Feed, Base Printer
Run the print test or the diagnostic paper feed test and carefully
examine the area of the problem.
If paper is not feeding, make sure the paper is in the tray correctly
and is not damaged or stuck together. Make sure the D-roll is in
good condition and rotates when the magnet is picked. With the 500-
sheet trays, make sure the tension wheel is set high enough to give
good contact between the D-roll and the paper stack.
10R/12R/12C/12L/16L: Make sure the pick magnet is being
energized. The pick magnet should have a resistance of 100 to 250
Ohms. The voltage at (10R/12R/12C/12L) J22-2 (16L) J19-2 should
be +34V between picks, and drop to about +30VDC (it actually drops
to zero but most meters will not react quickly enough) briefly during
the pick; listen for the noise of the solenoid at the same time the
voltage changes. The magnet can be tested by shorting pin 2 to
ground and listening for it to pick.
10P: The 10P has a torquer motor to activate the D-roll. It is
connected at J22 of the system board, the voltage check is the same
as the 10R/12R/12C/12L/16L. The resistance of the motor is 88
Ohms. The motor can be tested by shorting pin 2 to ground and
listening for it to pick.
Diagnostic Information 25
4039-1XX
If paper feeds but stops undamaged in the paper path there may be
a sensor problem. Run the diagnostic test for the input and exit
sensors replace as necessary. Check the continuity of the cable
before replacing the sensor. The input sensor signal is on (10P)
J20-6 (10R/12R/12C/12L) J20-11 (16L) J17-11; the output sensor
signal is on (10P/10R/12R/12C/12L) J19-8 (16L) J16-8. The voltage
should be 0VDC when there is no paper in the sensor and +5VDC
when paper is present.
If paper is jamming, clean the paper path of obstructions or repair
any damaged parts. Very thin or thick paper, labels, transparencies,
or card stock will have a higher jam rate than regular xerographic
tray is installed correctly.
If paper is curling badly enough to cause a problem feeding or
stacking, see “Fuser Temperature And Warm-Up Time” on page 39.
Paper Feed, Duplex Unit
Check that all gears and belts are working correctly both in the
duplex unit and on the tray top cover, and that the gear on the tray
top cover engages the gear on the duplexer.
If paper is jamming in the table cover area, make sure the table
cover is properly installed. Run diagnostics Duplex Test 1 to make
sure the paper is feeding far enough into the duplex unit before
reversing. Examine the condition of all rollers.
paper tray, run diagnostics Duplex Test 2 to make sure there is no
slippage in the paper path. Make sure the paper tray top cover is not
damaged. Cold paper curl can also cause jams here; see “Fuser
Temperature And Warm-Up Time” on page 39.
If paper is jamming at the front exit, verify that the front exit deflector
switch is functioning by disconnecting (10P/10R/12R/12C/12L) J19
(16L) J16 and checking the resistance from pin 1 to pin 2 as you
operate the switch.
Also see “23 Paper Jams” on page 18
26 Service Manual
4039-1XX
Paper Feed Problem, Envelope+ Feeder/
100-Sheet Auxiliary Feeder
Check for the following: paper or envelope jammed in the feed path;
missing hold-down weight; adjustable guide out of position; feeder
cable loose, disconnected, or plugged in the wrong connector;
feeder incorrectly installed; worn or damaged rollers or gears;
warped or damaged envelopes being used; envelopes being
improperly installed (envelope flaps must rest against the paper
edge guide); envelopes other than 20- or 24-pound being used in
the envelope+ feeder; paper other than 20- or 24-pound being used
in the 100-sheet auxiliary feeder; envelopes being interleaved with
paper.
Run the diagnostics Envelope Feed test and make sure the feed
magnet is being energized. If not, check the resistance of the
magnet at (10P/10R/12R/12L/12C) J12-1 to J12-2 (16L)J9-1 to J9-2
on the feeder cable; the resistance should be from 105 Ohms to 155
Ohms. If the magnet is good, reconnect the cable and monitor the
voltage between the two pins of the connector while running the
Envelope Feed test; if the voltage does not increase momentarily as
the magnet is picked, replace the system board.
Check the adjustment of the feeder magnet. If paper is being bent or
double-fed, check the adjustment of the feeder restraint spring.
Printhead
Note: The printhead is a sealed unit. It contains no parts that can
replaced or serviced.
Verify the continuity of the fan/mirror motor cable and the hsync
cable. Verify the presence of the following voltages: +24VDC at
(10P/10R/12R/12C/12L) J5-1 (16L) J3-1, +5VDC at (10P/10R/12R/
12C/12L) J6-5 (16L) J4-5, +5VDC at (10P/10R/12R/12C/12L), J6-1
(16L) J4-1.
If these voltages are not correct, replace the system board.
Verify +5VDC at pin 5 on the fan/mirror motor cable at the mirror
motor board. If the voltage is correct replace the printhead; if the
voltage is bad and the cable is OK replace the system board.
Diagnostic Information 27
4039-1XX
Paper Size Sensing Problem
(The printed area does not fit on the page, or the paper size cannot
be changed from the operator panel.)
Make sure that paper trays for the 4019, 4028, or 4029 are not being
used in the 4039 printer.
Make sure the paper tray and its stops are undamaged. Make sure
the cable to the paper size switch is connected correctly.
Disconnect (10P/10R/12R/12C/12L) J19 (16L) J16 from the system
board before making the following measurements. With the tray
removed, make sure there is no continuity from (10P/10R/12R/12L/
12C) J19-3 to J19- 4 (16L) J16-3 to J16-4 on the cable; replace the
paper size switch if the resistance is not infinite.
The resistance from (10P/10R/12R/12L/12C) J19-3 to J19-4 (16L)
J16-1 to J16-2 varies with the paper size. With the tray installed, if
the readings do not match the following within 5% replace the paper
size sensor.
A5
1.4 K Ohms (tray 1 only)
2.0 K Ohms
B5
10.5”
11”
3.0 K Ohms
4.7 K Ohms
A4
8.0 K Ohms
13” or 14”
17.8 K Ohms (legal tray)
If the problem is with the 500-sheet option, the resistance from (10P/
10R/12R/12L/12C) J17-3 to J17-4 (16L) J14-3 to J14-4 should be
infinite with no tray installed, or with the tray installed, should match
the table.
28 Service Manual
4039-1XX
Regularly Spaced Marks
This is caused by a defect on one of the rolls or gears in the print
process. The damaged part can be determined by the spacing of the
marks according to the following table. Find and replace the
damaged part.
Component
Print Defect Spacing on Page
PC Drum (part of print cartridge)
Transfer Roll
125.7 mm
53.1 mm
Fuser Hot Roll10P/12R/12C/12L/16L
Fuser Hot Roll 10R
78.9-79.2 mm
64.7 mm
Fuser Backup Roll
69.1 mm
Charge Roll (part of print cartridge)
Developer Roll (part of print cartridge)
Prealigner Feed Roller
37.1-37.7 mm
40.0 mm
68.5 mm
Auxiliary Feed Roller
68.5 mm
Spacings other than the ones listed could be caused by damage or a
bind in the gear train.
Residual Image
Residual image--the “walking” of a leftover image down the page--is
probably the result of failed erase lamps not discharging the
photoconductor, or of a failed cleaner inside the print cartridge. It
can also be caused by a failed fuser hot roll retaining toner and
redepositing it on the page. Check that the erase lamp voltage at
(10P) J20-1 (10R/12R/12C/12L) J20-16 (16L) J17-16 is +24VDC
and that the cable has continuity.
To test the erase lamps, jumper (10P) J20-2 (10R/12R/12C/12L)
J20-15 (16L) J17-15 to ground.
Diagnostic Information 29
4039-1XX
Random Marks
Random marks are nearly always due to a mechanical problem or
due to foreign matter loose in the printer or in the print cartridge.
Inspect and clean the inside of the printer carefully and correct any
problems found.
Skew, all edges
If the test print frame is parallel to all edges of the page but the
margins are not all the same width see “Print Registration
Adjustment” on page 61.
If the test print frame is not parallel to the left and right edges of the
paper, the paper has skewed in the paper path. Check the paper
path for obstructions. Make sure the paper in the tray is loaded
properly and is undamaged. Check the prealigner, drive, and
auxiliary rollers, springs, and backup rollers for dirt, wear, or
damage; refer to the parts catalog for repair kits for broken bellcrank
spring attachment hooks on the sideframe. Make sure all the
bellcrank assemblies pivot freely. Check the gear train for damage or
binds.
Skew, top and bottom only
If the test print frame is parallel to the left and right edges of the
paper but not parallel to the top and bottom, the printhead skew
needs to be adjusted. See “Printhead Skew - Level 1” on page 59
and “Printhead Skew - Level 2” on page 60.
Stalled (diamonds on display)
Check the continuity of the cable from (10P/10R/12R/12C/12L) J7
(16L) J5 on the system board to the operator panel. Next, reseat the
ROM and memory SIMMs and POR. This condition can also occur
on models 10R/12R/12L/12C if a network card is installed without
the accompanying DC power card.
30 Service Manual
4039-1XX
If the problem is still present, replace one at a time the:
1. ROM SIMM
2. System board
Vertical Void or Streak
Do a developed image test to determine if the defect is occurring
before or after the transfer process.
If you see the defect on the photoconductor, check the operation of
the printhead shutter and clean the printhead window with a lint-free
cloth folded over a cotton swab; do not use a bare swab and do not
use any cleaning fluids or water on the printhead window. Inspect
the HVPS contacts.
If the image on the photoconductor is good, inspect the fuser rolls
and transfer roll. Make sure the left transfer roll bearing is contacting
the contact from the HVPS. Make sure the HVPS contacts are clean
and spring back when pressed.
Diagnostic Information 31
4039-1XX
Diagnostic Aids
Diagnostics Mode
To run some of the printer diagnostic tests described in this chapter,
you must put the printer in Diagnostics mode.
To enter Diagnostics mode:
1. Turn the printer off.
2. Press and hold the Ready and Return buttons. Then turn the
printer on. The printer performs the Power-On Self Test.
3. Release the buttons when [Performing Self Test] is displayed.
4. You can exit Diagnostics mode without a POR by selecting
[Reset Printer].
Diagnostic Aids 32
4039-1XX
Grouped Diagnostic Aids
Print Tests
Operator Panel Tests
Print Test Page
Developed Image Test
Print Tests
Button Test
LCD Test
Duplex Tests
Duplex Feed 1
Duplex Feed 2
Registration Tests
Print Registration
Quick Test
Paper Feed Tests
Page Counts
Envelope Print Test
Paper Feed Test
Page Count
Maintenance Kit Count
Permanent Page Count
Printer Setup Tests
Device Tests
Envelope Enhance
Print Contrast (Transfer)
Fuser Temperature/Warm-up Time
Quick Disk Test
Disk Test/Clean
Hardware
Connection Checks
Defaults
Memory Tests
Sensor Test
LAN Information
Wrap Tests
Serial Interface Option
Auto Clean
Auto Clean Frequency
Auto Clean Delay
Error Log
Diagnostic Aids 33
4039-1XX
Alphabetical List of Diagnostic Aids
Auto Clean
Auto Clean needs to be turned on if there is an unacceptable
amount of toner being deposited on the back of the page. When
Auto Clean is on, after printing the number of pages specified in
Auto Clean Frequency, the printer pauses the number of seconds
specified in Auto Clean Delay. This pause minimizes the toner
accumulating on the fuser cleaner.
1. Enter Diagnostics mode.
2. Select [Auto Clean].
3. Select [On] or [Off].
4. Press Return to return to Diagnostics mode main menu.
Auto Clean Delay
This can be set from 1 to 60 seconds with a default of 1. Auto Clean
Delay does not appear on the menu unless Auto Clean is on.
1. Enter Diagnostics mode.
2. Select [Auto Clean Delay].
3. Select [+] or [-] to display the delay desired.
4. Select [SAVE].
5. Press Return to return to Diagnostics mode main menu.
Auto Clean Frequency
This can be set from 10 to 255 pages with a default of 50. Auto
Clean Delay does not appear on the menu unless Auto Clean is on.
1. Enter Diagnostics mode.
2. Select [Auto Clean Frequency].
3. Select [+] or [-] to display the frequency desired.
4. Select [SAVE].
5. Press Return to return to Diagnostics mode main menu.
34 Service Manual
4039-1XX
Defaults
Allows setting the following defaults to U.S. or Non U.S. values.
U.S.
NON U.S.
Letter size paper
# 10 envelopes
A4 paper
DL envelopes
Symbol Set PC-850
Symbol Set Roman-8
1. Enter Diagnostics mode.
2. Select [Defaults].
3. Select [U.S.] or [Non U.S.].
4. Press Return to return to Diagnostics mode main menu.
Developed Image Test
Use the Developed Image Test to isolate print quality problems. You
might have to practice this procedure several times to get the timing
correct.
To run the Developed Image Test:
1. Set the paper exit lever to use the front exit.
2. Print the test page.
3. As soon as the leading edge of the paper is visible coming out
the front exit slot, turn off the printer.
4. Remove the print cartridge and look at the image on the
photoconductor.
Disk Test/Clean
This is a two hour test that should be performed only on a disk that
contains bad data and is therefore unusable.
This test destroys all data on the disk by doing a multi-pass write/
read on every block of the disk. Bad blocks are flagged and removed
from use. If over 2000 bad blocks are found the test stops and the
display indicates the disk must be replaced.
Diagnostic Aids 35
4039-1XX
A message describing test progress is displayed during the test.
1. Enter Diagnostics mode.
2. Select [Device Test]
3. Select [Disk Test/Clean].
4. Select [CONTINUE] to start the test, or [CANCEL] to return to
Diagnostics mode main menu.
5. Select [CANCEL] to interrupt the test.
6. Press Return to return to Diagnostics mode main menu.
Duplex Feed 1 Test
This test checks for slipping paper problems. It verifies that the
paper is entering the duplex unit far enough for the trailing edge to
clear the selector fingers before the paper reverses direction.
1. Enter Diagnostics mode.
2. Select [Duplex Tests].
3. Select [Duplex Feed 1].
4. Select [Tray 1], or [Tray 2].
Note: Paper feeds all the way into the duplex unit and stop.
5. The message [CLEAR PAPER] appears on the display.
6. Slide the tray extension all the way out until it stops.
7. Push a small screwdriver through the lower end of one of the
ventilation slots and through the sheet of paper fed in under the
slot.
8. Open the cover and remove the sheet of paper.
9. Measure the distance from the mark on the paper to the trailing
edge of the paper. If the mark, or hole, is more than 95 mm from
the trailing edge, there is a paper slipping problem with the
duplex unit paper feed.
36 Service Manual
4039-1XX
Duplex Feed 2 Test
This test verifies that paper feeds through the duplex unit properly
and tests the stop point of the page as it feeds back over the top of
the duplex paper tray.
1. Enter Diagnostics mode.
2. Select [Duplex Tests].
3. Select [Duplex Feed 2].
4. Select [Tray 1] or [Tray 2].
Note: Paper feeds all the way into the duplex unit and then feed out
and stop on top of the paper tray.
5. The message [CLEAR PAPER] appears on the display.
6. Open the printer top cover.
7. If you are doing the test with legal size paper, open the top cover
of the duplex unit.
8. Carefully remove the duplex unit from the printer without
disturbing the position of the paper on the top of the duplex tray.
Do not disconnect the duplex cable from the printer.
9. Without changing the position of the page, hold it to the top of
the paper tray and remove the paper tray.
10. Measure from the leading edge of the page to the leading edge
of the paper stack in the tray. This measurement should be
75 mm or less. If it is larger than 75 mm, there is a drive problem
in the duplex unit or in the tray top cover.
11. Select [CONTINUE].
12. Perform the test several times to verify that the measurement is
accurate.
13. Press Return to return to Diagnostics mode main menu.
Diagnostic Aids 37
4039-1XX
Envelope Enhance
Use this procedure to set the fuser solenoid power level to low,
medium, or high. Increase the level to reduce envelope wrinkling, or
decrease the level to reduce solenoid noise.
1. Enter Diagnostics mode.
2. Select [Envelope Enhance].
3. Select [Low], [Medium], or [High].
4. Press Return to return to Diagnostics mode main menu.
Envelope Print Test
Note: Printing only occurs on the first envelope. The envelope feeds
from the automatic envelope feeder if present. If there is no auto-
matic feeder present, the printer uses manual envelope.
1. Enter Diagnostics mode.
2. Select [Envelope Print].
3. Select [Single] or [Continuous].
4. Select [CANCEL] to stop continuous envelope feed.
5. Press Return to return to the Diagnostics mode main menu.
Error Log (“plus” machines only)
The error log records the last 6 “2X Paper Jam” or “9XX Service”
errors. In a full log, position 6 is the oldest error. If more than 6 errors
are received, the oldest error is discarded. If the same error occurs
consecutively it is recorded only once.
All 97X Network Card errors are logged as 977.
1. Enter Diagnostics mode.
2. Select [Error Log].
3. Select [CLEAR] and then [CONTINUE] to clear the error log.
4. Press Return to return to Diagnostics mode main menu.
38 Service Manual
4039-1XX
Fuser Temperature And Warm-Up Time
These settings allow adjustment of the fuser to correct problems with
paper curl or melting letterheads.
Paper curl in which the top and bottom of the page curl toward the
printed side (hot paper curl) can be corrected by reducing the fuser
temperature. Reduce the setting from Normal to No Boost; if
necessary, reduce the setting further to Low Temperature. Verify that
the toner is being adequately fused to the paper at the new
temperature setting.
Paper curl in which the edges of the paper curl toward the printed
side (cold paper curl) can corrected by increasing the fuser warm-up
time. Use the lowest setting that corrects the problem. Setting “0” is
the factory default and is the shortest warm-up time. Setting “5”
increases warm-up time by 90 seconds; lower settings increase the
time proportionately less. Settings other than “0” may reduce
throughput. Use the + or - key to change the number and then select
save.
Melting letterheads may be prevented by reducing the fuser
temperature as described above for paper curl.
Fuser Temperature
1. Enter Diagnostics mode.
2. Select [Fuser Temperature].
3. Select [Normal], [No Boost], Or [Low Temperature].
4. Press Return to return to the Diagnostics mode main menu.
Warm-up Time
1. Enter Diagnostics mode.
2. Select [Warm-Up Time].
3. Select a setting of “0” through “5”. Use the + or - key to change
the number. 0 is the shortest fuser warm-up (factory setting). 5 is
the longest fuser warm-up.
4. Press Return to return to the Diagnostics main menu.
Diagnostic Aids 39
4039-1XX
Maintenance Kit Count
This non-displayed counter must be reset after the maintenance kit
is replaced to prevent the [80 Scheduled Maintenance] message
from displaying when the machine is turned on.
1. Enter Diagnostics mode.
2. Select [Maintenance Count].
3. Select [RESET] to set the count back to “0”.
4. Press Return to return to the Diagnostics mode main menu.
Memory Test
1. Enter Diagnostics mode.
2. Select [Memory Test].
3. Select either [DRAM] or [ROM].
4. Select [Single] or [Continuous].
5. The display indicates [PASSED], or [FAILED].
6. Select [CANCEL] to stop continuous memory test.
7. Press Return to return to Diagnostics mode.
Operator Panel Tests
The following tests check for proper functioning of the operator panel
buttons and display (LCD).
Button Test
To test the operator panel buttons:
1. Enter Diagnostics mode.
2. Select [Button Test].
3. Press each button. [Closed] is displayed until the button is
released. Then [Open] is displayed.
4. Press Return to return to the Diagnostics mode main menu.
40 Service Manual
4039-1XX
LCD Test
To test the operator panel display:
1. Enter Diagnostics mode
2. Select [LCD Test].
3. Select [Single] or [Continuous].
4. The display goes through a continuous sequence of turning pels
on and off.
5. Press Return to stop continuous LCD test.
6. Press Return to return to the Diagnostics mode main menu.
Page Count
To view or set the page count:
1. Enter Diagnostics mode.
2. Select [Page Count].
3. Choose any number between 0000000 and 9999999 by
Selecting [NEXT] to move the cursor under each digit. Then
select [+] OR [-] to select the number you want in each digit.
4. Select [SAVE] to save the page count displayed.
Paper Feed Test
This test allows you to observe the drive gear train and feed paper
through the printer to check for broken gear teeth, watch the paper
path, or check the erase lamps.
Note: You may want to remove the gear cover before starting this
test so you can observe the motor gears.
1. Enter Diagnostics mode.
2. Select [Paper Feed].
3. Select [Tray 1], [Tray 2], or [Manual].
4. Select [Single] or [Continuous].
5. Select [CANCEL] to stop continuous mode.
6. Press Return to return to Diagnostics mode main menu.
Diagnostic Aids 41
4039-1XX
Permanent Page Count
The permanent page count can be displayed only. It cannot be
modified or reset by the customer or servicer.
1. Enter Diagnostics mode.
2. Select [Permanent Page Count].
3. Press Return to return to Diagnostics mode main menu.
Print Contrast (Transfer on “plus” machines)
This setting changes the transfer roll voltage to light, medium, or
dark (low, medium, or high on “plus” machines), but seldom
produces a visible difference in print darkness. This setting may be
useful in environmental extremes to prevent toner from being
deposited in white areas next to large black areas.
1. Enter Diagnostics mode.
2. Select [Print Contrast].
3. Select [Light], [Medium] or [Dark]; ([Low], [Medium] or [High] on
plus machines).
Print Registration
See “Print Registration Adjustment” on page 61.
Print Test Page
You can run the Print Test even if the printer is not attached to a
computer. Use this test to check print and graphics quality and the
version numbers of printer microcode. The first page of this test
feeds from tray 1. Following pages continue to feed from this tray
unless you change the paper source.
To run the Print Test:
1. Turn the printer on.
2. Select [MENUS].
3. Select [TESTS MENU].
42 Service Manual
4039-1XX
4. Select [Print Test Page].
5. Select either [Single] or [Continuous] depending if you want one
page or continuous test pages.
6. Select [Stop] when you want the continuous test to end.
Print Tests
All of the print tests can be run in the [Single] or [Continuous] mode.
To stop continuous printing select [CANCEL].
Print Test 1
Print Test 1 generates one print out similar to the test page. This test
uses paper from tray 1 only. Print Test 1 will not duplex.
To run Print Test 1:
1. Enter Diagnostics mode.
2. Select [Print Test 1].
3. Select [Single] or [Continuous].
4. Select [CANCEL] to stop continuous print.
5. Press Return to return to the main Diagnostics menu.
Print Test 2
Print Test 2 generates two printouts: a page similar to the test page,
and a fine dot pattern which can be used to evaluate banding or
other print quality problems.
Print Test 2 duplexes if the duplex option is installed.
To run Print Test 2:
1. Enter Diagnostics mode.
2. Select [Print Test 2].
3. Select [Single] or [Continuous].
4. Select [Cancel] to stop continuous print.
5. Press Return to return to the main Diagnostics menu.
Diagnostic Aids 43
4039-1XX
Print Test 3
This test generates 2 printouts: a solid black page, and a dot pattern
that can be used to evaluate print quality.
1. Enter Diagnostics mode.
2. Select [Print Test 3].
3. Select [Single] or [Continuous].
4. Select [CANCEL] to stop continuous print.
5. Press Return to return to Diagnostics mode main menu.
Quick Disk Test
This is a one minute test which performs a non-destructive write/
read on one block per track on the disk. It tests the printer-to-disk
communications, and the disk hardware and circuitry but does only
incidental testing of the disk surface itself.
The Quick Disk Test does not destroy data on the disk; existing data
is read and stored prior to the testing of each track, and then re-
written after the track is tested.
1. Enter Diagnostics mode.
2. Select [Quick Disk Test].
3. The display indicates [Test Passed] or [Test Failed].
4. Press Return to return to Diagnostics mode main menu.
Quick Test
The Quick Test is activated by pressing Ready from any screen
while in Diagnostics mode (“plus” machines only), as well as being
an entry under [Print Registration]. It provides a simple page
alignment pattern that prints faster than the other print tests.
44 Service Manual
4039-1XX
Sensor Test
1. Enter Diagnostics mode.
2. Select [Sensor Test].
3. Select one of the following sensor tests.
•
•
•
•
•
Toner Low
Output Bin
Input
Exit
Cover Open
Note: The Output Bin sensor can have up to a 15 second delay
in changing to open.
4. When the sensor is blocked [Open] is displayed. Otherwise,
[Closed] is displayed.
5. Press Return to return to the Diagnostics mode main menu.
Diagnostic Aids 45
4039-1XX
Network Connections and Checks
Wrap Tests
The Wrap Tests check the circuits used to communicate with the
host computer.
To run the Wrap Test:
1. Turn the printer off.
2. Disconnect the interface cable.
3. Install the wrap plug in one of the interface cable connectors.
Note: Install the parallel wrap plug part no. 1319128 for the parallel
test or install the 25 pin serial wrap plug part no. 1329048 for the
serial test.
4. Enter Diagnostics mode.
5. Select [Wrap Test].
6. Select [Parallel] for the parallel port or [Serial] for the 25 pin
serial port.
7. Select [Single] or [Continuous].
8. Select [CANCEL] to stop continuous.
A [PASSED] message indicates the printer connection to the printer
cable connector is good.
A [FAILED] message indicates a defective system board.
Note: Ignore the number displayed after a failure is displayed.
9. Press Return to return to the Diagnostics mode main menu.
10. Turn the printer off, then remove the wrap plug from the interface
connector.
46 Service Manual
4039-1XX
LAN Information
The printer may be connected to one of the following LAN types:
Token-Ring
Ethernet 10BaseT
Ethernet 10Base2
LocalTalk
The Network external connectors are pictured below. The printer test
page also indicates to which type of LAN the printer is connected.
Serial Interface Option, 10P
The serial interface unit switch settings determine how the printer
receives data from the computer or terminal. Set the switches
according to your particular equipment requirements.
The serial interface has 12 function switches.
Function Switch Setting
Switches 1 to 4 — Speed: Switches 1 through 4 define the serial
interface speed in bits per second (bps).
1
2
3
4
SPEED (BPS)
On
On
On
On
Off
Off
Off
On
Off
Off
Off
Off
150
300
600
Diagnostic Aids 47
4039-1XX
1
2
3
4
SPEED (BPS)
Off
Off
Off
Off
On
Off
On
On
Off
Off
On
Off
On
Off
On
Off
On
Off
Off
Off
Off
Off
Off
On
1,200
2,400
4,800
9,600 (default)
19,200
38,400 (RS-422 only)
Switch 5 – Data Bits: Switch 5 selects the number of data bits
(7 or 8) in each data frame.
5
DATA BITS
Off
On
8
7
Switch 6 and 7 – Parity: Switches 6 and 7 select the interface
parity.
6
7
Parity
Off
Off
On
On
Off
On
Off
On
No
Ignore
Odd
Even
Note: When setting the “Ignore” for parity, the printer ignores the
received parity and transmits using Even parity. For all other parity
settings, the transmitted parity matches the received parity.
48 Service Manual
4039-1XX
Switch 8 – Buffer Size: Switch 8 allows the adapter buffer size to
be limited, to minimize the amount of data in the buffer at any time.
8
Buffer Size
Off
On
Normal
Minimum
Switch 9 – Protocol: Switch 9 selects the type of protocol.
9
Protocol
Off
On
DTR pacing (RS232 only)
XON/XOFF
Switch 10 - Print Test: Switch 10 selects the print test for the serial
interface card. This tests the connection between the serial interface
unit and the printer. The printout contains the serial interface unit
code level and switch settings, and the printer character set.
Note: For the serial print test to work [Advanced Status] (found
under the [PARALLEL SETUP] menu) must be set to [Off].
To run the serial interface test print:
1. Turn the printer power off.
2. Set serial interface Switch 10 [On].
3. Turn the printer power on.
If the printer does not generate a printout, there is a problem with the
serial interface card or its connection to the printer. Check the switch
settings and ensure that the serial interface unit is correctly installed.
When the test is complete, reset Switch 10 to [Off].
10
Print Test
Off
On
Normal Mode
Test mode
Diagnostic Aids 49
4039-1XX
Switch 11 – Polarity for RS-422 Serial Interface: Switch 11 is
used to reverse the polarity of the receive and transmit data line for
the RS-422 serial interface.
11
Mode
Off
On
Normal
Reverse
Switch 12 – Interface: Switch 12 sets the serial interface in either
RS-232C or RS-422 mode.
12
Mode
Off
On
RS-232C
RS-422
50 Service Manual
4039-1XX
Repair Information
This chapter explains how to make adjustments to the printer and
how to remove defective FRUs.
Handling ESD-sensitive Parts
Many electronic products use parts that are known to be sensitive to
electrostatic discharge (ESD). To prevent damage to ESD-sensitive
parts, follow the instructions below in addition to all the usual
precautions, such as turning off power before removing logic boards:
•
•
•
•
•
•
Keep the ESD-sensitive part in its original shipping container (a
special “ESD bag”) until you are ready to install the part into the
machine.
Make the least-possible movements with your body to prevent an
increase of static electricity from clothing fibers, carpets, and fur-
niture.
Put the ESD wrist strap on your wrist. Connect the wrist band to
the system ground point. This discharges any static electricity in
your body to the machine.
Hold the ESD-sensitive part by its edge connector shroud
(cover); do not touch its pins. If you are removing a pluggable
module, use the correct tool.
Do not place the ESD-sensitive part on the machine cover or on
a metal table; if you need to put down the ESD-sensitive part for
any reason, first put it into its special bag.
Machine covers and metal tables are electrical grounds. They
increase the risk of damage because they make a discharge
path from your body through the ESD-sensitive part. (Large
metal objects can be discharge paths without being grounded.)
•
Prevent ESD-sensitive parts from being accidentally touched by
other personnel. Install machine covers when you are not work-
ing on the machine, and do not put unprotected ESD-sensitive
parts on a table.
•
•
If possible, keep all ESD-sensitive parts in a grounded metal
cabinet (case).
Be extra careful in working with ESD-sensitive parts when cold-
weather heating is used because low humidity increases static
electricity.
Repair Information 51
4039-1XX
Adjustments
Envelope Restraint Spring On The Envelope+ Feeder
1. Loosen the mounting screw [A].
2. Position the spring [B] so it clears the separator roller by
1.9 ±0.2 mm (0.075 ±0.008 in.).
3. Tighten the mounting screw.
Paper Restraint Spring On The 100-sheet
Auxiliary Feeder
1. Loosen the mounting screw [A].
2. Position the spring [B] so it clears the separator roller by
1.9 ± 0.2 mm (0.040 ±0.008 in.).
3. Tighten the mounting screw.
52 Service Manual
4039-1XX
Envelope Feeder Magnet And 100-sheet
Auxiliary Feeder Magnet
1. Hold the armature [A] in the closed (coil active) position.
2. Loosen the mounting screw [B], and rotate the magnet assembly
so the armature clears the clutch gear by 0.30 ± 0.20 mm (0.012
± 0.008 in.).
3. Tighten the screw.
4. Check the adjustment on both sides of the gear.
Repair Information 53
4039-1XX
Fuser Drive Gear Backlash
Fuser drive gear backlash is adjusted so that when gear #2 is held
still, there is a slight amount of backlash in the fuser gear. Print
quality can be affected if the gears are too tight.
1. Remove the fuser cover.
2. Locate gear #2. It is the white adjustable gear mounted to the
side frame below the fuser gear.
3. Rotate the adjustable gear in one direction to check for backlash.
To adjust backlash:
1. Loosen the nut on the idler stud.
2. Move the idler stud downward in its slot.
3. Insert a 0.95 mm (.037) feeler gage between the gear shoulders
from the front of the machine. You may need to use an angled or
very small feeler gauge.
4. With the nut snug but not tight, tap the idler upward until the
gage is snug between the gear shoulders.
5. Tighten the locking nut.
6. Check the clearance again; tightening may have altered the
adjustment. Be sure the fuser gear can be rotated slightly when
gear #2 is held still.
54 Service Manual
4039-1XX
Repair Information 55
4039-1XX
Fuser Solenoid
Note: The fuser solenoid must be mounted on the fuser for this
adjustment and should be at room temperature.
1. Loosen screw [A].
2. Remove the rubber washer.
3. Rotate shaft [B] (eccentric) to obtain 4.2 mm ± 0.2 mm
(0.165 in.± 0.008 in.) air gap.
4. Tighten screw [A].
5. Replace the rubber washer.
56 Service Manual
4039-1XX
Paper Feed Magnet
1. Remove the system board. The magnet is accessed through the
holes in the right frame.
2. With the armature latched on the cam step check for 0.60 mm ±
0.07 mm (0.024 in ± 0.003 in.) between the foam pad and the
magnet pole piece. If adjustment is required, continue:
3. Keep the armature latched and loosen the magnet mounting
screw [A].
4. Insert feeler gage.
5. Rotate the magnet against the feeler gage.
6. Tighten the mounting screw.
7. The gage should pass between the foam pad and the magnet
pole piece with moderate resistance.
Repair Information 57
4039-1XX
Optional Paper Feed Magnet
1. With the armature latched on the cam step check for 0.60 mm
± 0.07 mm between the foam pad and the magnet pole piece. If
adjustment is required, continue:
2. Keep the armature latched and loosen the magnet mounting
screw [A].
Note: The flat side of the D-roll is down when the feed is latched.
3. Insert feeler gage.
4. Rotate the magnet against the feeler gage.
5. Tighten the mounting screw.
6. The gage should pass between the foam pad and the magnet
pole piece with moderate resistance.
58 Service Manual
4039-1XX
Printhead Skew - Level 1
1. Loosen the mounting screws [A].
2. Pivot the printhead around the shoulder screw [B] until the skew
marks on the printout are parallel to the top edge of the paper.
Use Print Test 1 or Quick Test to check this. Rotating the
printhead clockwise will lower the left skew adjustment point on
the test print.
3. Tighten the screws.
4. Install the top cover and print another page to verify the
adjustment.
B
A
Skew Adjustment Points
Repair Information 59
4039-1XX
Printhead Skew - Level 2
1. Remove the top cover.
2. Loosen the screws [A].
3. Run Print Test 1 or the Quick Test on the Diagnostics Menu.
4. Move the pointer [B] to eliminate the skew. Moving the pointer
toward the left raises the left adjustment point on the printout.
5. Tighten the screws, and verify the adjustment.
A
B
Skew Adjustment Points
60 Service Manual
4039-1XX
Print Registration Adjustment
Use Print Test 1 or the Quick Test to evaluate print registration.
Adjust the registration so the tips of the diamonds are at the top and
bottom edges of the page and the printout is centered left to right.
Verify that the to Top Margin is correct before adjusting the Bottom
Margin.
1. Enter Diagnostics mode.
2. Select [Print Registration].
3. Select one of the following: [Left Margin], [Top Margin], or
[Bottom Margin].
4. The value of the margin you selected is shown.
5. Left Margin: This margin can be set between -23 and +23.
Changing the number by one moves the margin 1/75 inches.
Moving the number in a positive direction moves the margin
toward the right and negative moves the margin to the left.
6. Top Margin: This margin can be set between -20 and +20.
Changing the number by one moves the margin by 1/75 inches.
Moving the number in a positive direction moves the margin
down the page and widens the top margin. Moving the number in
a negative direction moves the text up the page and narrows the
top margin.
7. Bottom Margin: This margin can be set between -7 and +7.
Moving the number in a positive direction moves the margin
down and narrows the bottom margin. Moving the number in a
negative direction moves the text up the page and leaves a wider
bottom margin.
8. Select [+] to move the number in a positive direction.
9. Select [-] to move the number in a negative direction.
10. Select [Print Test 1], or [Quick Test] to check your settings.
11. Select [Tray 1], or [Tray 2].
12. Select [Single], or [Continuous].
13. Select [SAVE] to save your settings when they are correct.
14. Press Return to return to the Diagnostics menu.
Repair Information 61
4039-1XX
Removals
When there is artwork to support a procedure, it follows the text.
Covers
Right Cover Removal
1. Turn the printer off.
2. Remove all external trays.
3. Open the top cover.
4. Swing the cover open.
5. Remove the E-clip from the rear pivot pin and lift the cover off the
rear pivot pin.
Front Cover Removal
1. Unplug the power cord.
2. Remove the paper tray.
3. Open the top cover.
4. Open the right cover.
5. Remove the Duplex mounting slot covers.
6. Release the latches [B]. You can reach the lower latches through
the paper tray opening.
7. Pull the front cover forward, then move the cover to the right to
separate the on/off switch linkage [D].
8. Disconnect the ground strap from the frame on the left side.
9. Remove the front exit deflector switch.
62 Service Manual
4039-1XX
Repair Information 63
4039-1XX
Left Cover Removal
1. Unplug the power cord.
2. Open the top cover and remove the print cartridge.
3. Remove the front cover.
4. Locate the latch [A] and push the end to the rear to release it.
5. Push the top of the cover to the left.
6. Remove the cover by sliding it to the rear of the machine.
Top Cover Removal
1. Remove the top cover screws [C].
2. Lift the rear of the cover first, then the front, and lift the cover off.
3. Rest the cover on the machine and disconnect the operator
panel cable and the ground wire.
64 Service Manual
4039-1XX
Repair Information 65
4039-1XX
Transfer Roll Removal
1. Unplug the power cord.
2. Remove the print cartridge.
3. Remove the bearing cover from the left side of the transfer roll:
Note: Do not touch the transfer roll surface.
• Support the left bearing cover from the front with your left
hand.
• Use a small screwdriver to push the rear latch forward and
release the bearing cover. This exposes the bearing on the
end of the transfer roll.
4. Grasp the bearing on the end of the transfer roll. Lift slightly and
move it to the left until the right end of the transfer roll shaft
slides out of the right side bearing.
5. Remove the transfer roll.
6. Lift the right bearing straight up and out of the machine.
66 Service Manual
4039-1XX
D-roll Assembly Removal
1. Unplug the power cord.
2. Remove the paper tray.
Note: The following 3 steps are not necessary, but may make it
easier to see the parts.
3. Remove the print cartridge.
4. Remove the fuser input guide.
5. Remove the transfer roll housing assembly.
6. Move your finger down off the end of the shaft to the latch
located above the flat part of the D-roll.
7. Push the latch down (away from the shaft) and slide the D-roll to
the left, off the shaft.
Note: There is no positive detent when replacing the D-roll. Make
certain the roll is in place by pulling toward the left without pushing
the latch.
Note: Later machines do not have a latch. Remove the D-roll by
pulling it firmly to the left. The D-roll without a latch is intended to be
installed only once; if it is removed for any reason it should be
replaced with a new one. The new D-roll may take considerable
force to install.
Repair Information 67
4039-1XX
Drive Motor Removal
1. Unplug the power cord.
2. Remove the system board.
3. Remove the system board inner EMC shield.
4. Remove the fuser input guide [A].
5. Remove the transfer housing assembly.
6. Remove the gear cover by releasing the rear latch and lifting up.
7. Remove screw [C] and the grounding clip (this clip is not present
on all machines).
8. Remove the motor mounting nuts [B] and screws.
9. Work the motor out of the machine.
10P: Do not remove the motor from the gear bracket assembly; they
are not available separately.
Installing the motor: If the motor has been removed from the gear
bracket assembly, you must use the gear retaining plate as a tem-
plate to be sure the motor pinion is correctly positioned to gear 4.
Install the gear retaining plate to the gear bracket assembly and
tighten the nuts. Install the motor to the assembly and tighten the
screws. Remove the gear retaining plate from the assembly and
install the motor in the printer.
68 Service Manual
4039-1XX
Repair Information 69
4039-1XX
Fan/Redrive Removal
1. Open the top cover.
2. Remove the print cartridge.
3. Remove the top cover.
4. Remove the lower redrive shaft by disengaging the right end to
the rear of the machine.
5. Disconnect the long redrive belt [A] and slip it off the lower shaft.
6. Remove the redrive assembly screws [D].
7. Remove the plenum assembly and screws [B].
8. Unplug the fan cable. The fan [C] can now be removed from the
plenum assembly.
70 Service Manual
4039-1XX
D
B
A
C
Repair Information 71
4039-1XX
Fuser Removal
Note: The heater lamp is fragile and may be damaged if you are not
careful when you remove or replace the fuser unit.
CAUTION: THE TEMPERATURE OF THE HOT ROLLER IS
150°-230°C (302°- 446°F). USE EXTREME CAUTION WHEN
REMOVING THIS UNIT. BEFORE YOU SERVICE THIS UNIT,
ALLOW THE MACHINE TO COOL FOR 5 MINUTES.
1. Unplug the power cord.
2. Remove the printer cartridge.
3. Disconnect the exit sensor cable from the fuser through the
opening for the paper output.
4. Unsnap the front cover from the right side frame.
5. Remove the fuser cover.
6. Disconnect the power wires [A] from the left side of the fuser.
7. Remove the fuser input guide.
8. Completely loosen the four fuser mounting screws.
9. Lift the fuser out of the machine.
Fuser Input Guide Removal
1. Remove the fuser input guide [B] by lifting the rear end of the
guide and unsnapping both sides from the fuser.
2. Lift the fuser input guide upward at both sides near the fuser and
slide the guide toward the rear of the machine to release.
3. Lift the guide out of the machine.
4. Clean the fuser input guide before installing it.
72 Service Manual
4039-1XX
Repair Information 73
4039-1XX
Fuser Lamp Removal
CAUTION: THE TEMPERATURE OF THE HOT ROLLER IS
150°-230°C (302°-446°F). USE EXTREME CAUTION WHEN
REMOVING THIS UNIT. BEFORE YOU SERVICE THIS UNIT,
ALLOW THE MACHINE TO COOL FOR 5 MINUTES.
Note: The fuser lamp is a glass heater. Do not touch the lamp with
your hands; skin oils and acids can reduce the life of the heater
lamp. Use a soft cloth to handle the heater lamp at all times if the
lamp is to be reinserted.
1. Remove the fuser.
2. Remove the right lamp bracket [A].
3. Carefully pull the lamp [B] out to the right, using a soft cloth if the
lamp is to be reinserted.
74 Service Manual
4039-1XX
Fuser Solenoid Removal
1. Remove the fuser.
2. Remove the two mounting screws [A] holding the solenoid
housing to the fuser housing.
3. Disengage the solenoid bracket from the plunger.
Note: When a new solenoid assembly is installed, the fuser
solenoid must be adjusted.
A
Repair Information 75
4039-1XX
Fuser Thermistor Removal
1. Disconnect the thermistor cable connector [A] from the exit
sensor card.
2. Remove the fuser cover and wiper.
3. Remove the tape holding the thermistor cable to the shroud.
4. Squeeze the thermistor bracket tabs [B] and remove the
thermistor from the shroud.
5. Remove the thermistor cable from the guide clips on the right of
the fuser to remove the thermistor.
76 Service Manual
4039-1XX
B
A
Repair Information 77
4039-1XX
HVPS Removal
1. Unplug the power cord.
2. Remove the left cover
3. Remove the fuser input guide.
4. Remove the transfer roll housing.
5. Remove the fuser cover.
6. Disconnect the cable from the HVPS connector.
7. Remove the power switch rod.
8. Remove the ground screw [B].
9. Remove the mounting screws [C].
10. Pull the ground strap through the hole [D].
11. The power supply is held in place by two latches on the left side.
To release the latches:
• Push one latch [E] in and raise one of the studs [F] to release
the latch.
• Push the other latch [E] in and raise the other stud [F] to
release the latch.
12. Lift the power supply until the studs [F] align with the large
openings, then move the power supply to the right to release it
from the frame.
13. Move the front of the power supply to the right (to clear the fuser
power wires).
14. Tilt the front of the power supply up and lift it out of the machine
78 Service Manual
4039-1XX
.
C
D
F
F
E
B
Repair Information 79
4039-1XX
Input Sensor Removal
1. Remove the fuser input guide [A].
2. Remove the transfer roll housing.
3. Remove the D-roll.
4. Disconnect the system cable from the input sensor board.
Note: Use care, the flag can be damaged while removing the
sensor.
5. Release latch [B] and pull the sensor down and forward to get it
out of its mounting.
6. Disconnect the toner sensor cable from the board.
7. Remove the sensor board.
A
B
80 Service Manual
4039-1XX
Lower Frame Assembly Removal
1. Remove the right, front, and left covers
2. Remove the LVPS and the rod for the on/off switch.
3. Remove gear cover and the fuser input guide [A].
4. Remove the transfer roll housing.
5. Disconnect the cable from the HVPS.
6. Remove the system board and the inner EMC shield.
7. Disengage the upper frame cables from the guide in the paper
feed side frame.
8. Remove the screws [B].
9. Remove the fuser cover.
10. Unplug the fuser wires [C] and push them below the HVPS.
11. Unplug the paper size switch cable.
12. Lift the lower frame assembly straight up to separate it from the
paper feed assembly.
Repair Information 81
4039-1XX
LVPS Removal
1. Disconnect the power cord.
2. Remove all external feed trays.
3. Remove the left and right side covers.
4. (10P and 16L) remove the system board and the inner EMC
shield.
5. Remove the left and right LVPS mounting screws.
6. Disconnect the fuser connector [A].
7. Lift the supply up and then toward the right side frame to
disconnect the On/Off switch linkage.
82 Service Manual
4039-1XX
Operator Panel Removal
1. Remove the top cover.
2. Disconnect the operator panel cable.
3. Remove the operator panel mounting screws from the inside of
the top cover.
Option Card Removal
1. Remove all external trays.
2. Open the top cover.
3. Open the right cover.
4. Remove the outer EMC shield.
5. Remove cable and mounting screws as required.
6. Pop the card off the plastic standoffs.
84 Service Manual
4039-1XX
Paper Feed Magnet Assembly Removal
1. Remove the print cartridge.
2. Remove the right cover.
3. Remove the system board.
4. Remove the inner EMC shield.
5. Locate the paper feed magnet mounting screw [B] (visible
through the right side frame [A]).
6. Remove the mounting screw [B].
7. Remove the paper feed magnet assembly from the rear (slip the
connector under the right frame).
A
B
B
86 Service Manual
4039-1XX
Paper Feed Rollers Removal
Note: Replace all paper feed drive rollers at the same time.
1. Remove the lower frame.
2. Disconnect the system cable from the input sensor.
3. Remove the screws [A] and the outer deflector.
4. Remove the screws [B] and the toner shield [E].
5. Separate the side frames.
6. Pull the guides [C] out of the side frames.
7. Use a flat-blade tool to snap the gears and rollers [D] off the
shaft.
Repair Information 87
4039-1XX
Paper Size Switch Removal
1. Open the top cover.
2. Remove the print cartridge.
3. Remove the paper tray.
4. Open the right side cover.
5. Remove the front cover.
6. Remove the two screws [A].
7. Unplug the cable [B] from the switch connector [C].
8. Rotate the switch about 90°and pull it out of the printer.
88 Service Manual
4039-1XX
Printhead Removal
IMPORTANT: The printhead is ESD-sensitive. It is not serviceable
and should be replaced as a unit.
1. Turn the printer off.
2. Remove the print cartridge.
3. Remove the right and top covers.
4. Remove the exit redrive and its belt.
5. Remove the air plenum.
6. Remove the screws [A] and the pointer if present.
7. Cut and discard the printhead cable clamp.
8. Disconnect the connectors [B].
9. Remove the printhead and the printhead shroud.
10. Pry off the grip rings holding the printhead to the shroud.
Note: After replacing the printhead perform the printhead skew
adjustment.
Repair Information 89
4039-1XX
System Board Removal
1. Check the page count and write it down so you can set the new
system board.
2. Turn the printer off.
3. Remove the right cover.
4. Remove the outer EMC shield by pressing down on the two
bottom tabs, slide the shield forward, then down (10P has no
outer EMC shield).
5. Disconnect all the external connectors from the system board
and remove the option cards.
6. Remove the system board mounting hardware [A].
7. Release the system board standoff.
8. Remove screw [B]. and remove the system board.
Note: If system board is being replaced, remove the ROM SIMM
and all options for installation on the new system board.
90 Service Manual
4039-1XX
Repair Information 91
4039-1XX
System Cable Removal
1. Turn the printer off.
2. Remove the right cover.
3. Remove the transfer roll housing.
4. Remove the fuser input guide.
5. Disconnect the system cable connections.
6. Remove the cable through the top of the machine.
Fuser/Sensor Cable Removal
1. Turn the printer off.
2. Remove the system board.
3. Remove the inner EMC shield.
4. Disconnect the cable from the exit sensor board.
5. Remove the front cover.
6. Remove the front exit deflector switch.
7. Disconnect the cable from the paper sensor assembly.
8. Remove the cable through the right frame.
Torquer Motor Removal (10P)
1. Remove the lower frame assembly from the base.
2. Remove the D-roll.
3. Remove the D-roll shaft/gear assembly, taking care not to lose
the two bushings.
4. Remove the two screws and remove the torquer motor and
adapter.
5. Unsnap the adapter from the motor.
Note: When reinstalling, align the timing marks on the torquer
motor gear and D-roll gear.
92 Service Manual
4039-1XX
Toner Sensor Removal
1. Remove the fuser input guide [A]
2. Remove the transfer roll housing.
3. Lift the input sensor board far enough to disconnect the cable
[B].
4. Remove the end of the bellcrank spring.
5. Lift the sensor to unsnap it.
6. Work the cable out of the frame and remove the sensor.
A
B
Repair Information 93
4039-1XX
Transfer Roll Housing Removal
1. Remove the print cartridge.
2. Remove the fuser input guide.
3. Grasp the housing and pull toward the front of the machine to
disconnect the housing from the mounting studs, visible through
openings [B] in the inner deflector.
4. Lift the transfer roll housing far enough to disconnect the system
cable.
5. Lift the transfer roll housing out of the machine.
6. To replace the transfer roll housing, perform the removal
procedure in reverse order. After replacing the Transfer Roll
Housing, open the top cover, power the machine off then on, to
ensure the erase lamps flash off and on.
94 Service Manual
4039-1XX
Upper Frame Removal
1. Unplug the power cord.
2. Remove the print cartridge.
3. Remove the right, left, and top covers.
4. Remove the system board.
5. Remove the inner EMC shield.
6. Remove the load box latches [A].
7. Release the latches [B].
8. Pivot the upper frame to the rear to release the spring tension.
9. Unsnap the plastic insert [D] holding the upper frame cables in
the right side frame.
10. Remove the screws [C].
11. Remove the upper frame cables through the side frame.
12. Lift the upper frame off the machine.
Repair Information 95
4039-1XX
Duplex Option Top Cover And Table Cover Removal
1. Open the top cover by pulling up at [A] and pivoting 90°.
2. Pry the top cover from the bottom cover at [B] and lay the top
cover on its side.
3. To disconnect the fan leads, the table cover has to be removed.
4. Release latches [C] on the paper table cover and lift up. Release
latch [D] and lift the paper table cover out of the frame assembly.
D
C
A
B
Repair Information 97
4039-1XX
Duplex Option Exit Card And Cover Removal
1. Pry up on tabs [A], after the tabs are released, lift up on the
cover, rotate the cover out, and slide it to the right to completely
remove it.
2. Disconnect the exit sensor card cable.
3. Depress the exit sensor flag actuator [B] and lift out the exit
sensor card.
Duplex Option Bottom Cover And
Entry Sensor Card Removal
1. Release the two latches [A] on the frame assembly and lift it out
of the bottom cover.
2. Pry up on the sensor card at [B], so it will clear the mounting
stud, and pull it out of the frame assembly.
Note: When re-installing the sensor, lift up the flags so they will
clear the sensor and not be damaged.
98 Service Manual
4039-1XX
Repair Information 99
4039-1XX
Duplex Option System Card And Motor Removal
1. Disconnect all cables.
2. Release latches [A] and lift the system board out.
4. Lift the motor out of the frame assembly.
Note: The remaining FRU is the Gearblock Assembly. When you
replace this FRU see “Lubrication Specifications” on page 120”.
Note: Reinstall the motor so the belt is not tight but will not jump
teeth on the timing pulley.
A
B
100 Service Manual
4039-1XX
Connector Locations
This chapter shows the locations of major printer assemblies, gears,
connectors, and ground straps.
Major Assembly Locations
Operator Panel
Upper Frame
Fan
Print Cartridge
Exit Redrive
Low Voltage
Power Supply
Print Head
High Voltage
Power Supply
Fuser
Transfer Roll
LowerFrame
System Board
Output Sensor
Toner Sensor
Paper Tray
Input Sensor
Paper Feed
Connector Locations 101
4039-1XX
System Board Connectors 10R/12R/12C/12L
Connector
Name
J1
DRAM SIMM
J2
DRAM SIMM
J3
ROM SIMM (flash memory option)
ROM SIMM (printer microcode)
Printhead Mirror Motor(Printhead)/ Fan
Laser (Printhead)/ Hsync
Operator Pane/Output Bin Sensor
DC to DC Convertor
DC to DC Convertor
INA Power Card
J4
J5
J6
J7
J8
J9
J10
J11
J12
J13
J14
J15
J16
J17
J18
J19
J20
LVPS
Envelope Feeder Magnet
INA Card
Serial
Parallel Port
Font Card
500 Sheet Option
Duplex
Fuser
HVPS Flex (Includes input and toner sensors
and erase lamps on transfer roller)
J21
J22
Paper Drive Motor
Paper Pick Magnet
Connector Locations 107
4039-1XX
System Board 16L
Connector
Name
J1
DRAM SIMM
J2
DRAM SIMM
J3
Mirror Motor(Printhead)/ Fan
Laser (Printhead)/ Hsync
Operator Pane/Output Bin Sensor
Duplex
J4
J5
J6
J7
Font Card
J8
Hard Disk Option
J9
Envelope Feeder Magnet
ROM SIMM (Printer microcode)
ROM SIMM (flash memory option)
INA Card
J10
J11
J12
J13
J14
J16
J16
J17
Parallel and Serial Port
500 Sheet Option
Paper Drive Motor
Fuser
HVPS Flex (Includes input and toner sensors
and erase lamps on transfer roller)
J18
J19
LVPS
Paper Pick Magnet
Connector Locations 109
4039-1XX
System Board 10P
Connector
Name
J1
N/A
J2
DRAM SIMM
J3
Option SIMM (flash memory option)
J4
ROM SIMM (printer microcode)
J5
Printhead Mirror Motor/Fan
J6
Printhead Hsync/Laser
J7
Operator Panel
J8
N/A
J9
N/A
J10
J11
J12
J13
J14
J15
J16
J17
J18
J19
J20
J21
J22
N/A
LVPS
Envelope Feeder Magnet
INA/Hard Disk
HVPS
Parallel Port
N/A
Second Paper Tray Option
Duplex
Exit &Paper Size Sensor/Fuser Solenoid
Input & Toner Sensor Board/Erase Lamps
Drive Motor
Torquer Motor (Tray 1 pick)
Connector Locations 111
4039-1XX
Printhead Cable
Pin
Laser
Hsync
1
2
3
4
5
6
7
8
9
10
1
2
3
4
6
5
4
3
2
1
Mirror Motor Cable/Fan Cable
The mirror motor cable connector for the 10P, 10R, 12R, 12L, and
12C is J5. The mirror motor cable connector for 16L is J3.
Pin
Motor
Fan
1
2
3
4
5
6
7
1
2
3
4
5
2
1
Connector Locations 113
4039-1XX
Pin
Op Panel
Sensor
1
2
3
4
5
6
7
8
9
1
2
3
4
5
1
2
3
4 *
* No connection on machines with
redrive-mounted output bin sensor.
116 Service Manual
4039-1XX
Load Box Shaft
to Upper Frame
Toner Shield
to Lower Frame
118 Service Manual
4039-1XX
Preventive Maintenance
This chapter describes procedures for printer preventive
maintenance. Following these recommendations can help prevent
problems and maintain optimum performance.
Safety Inspection Guide
The purpose of this inspection guide is to aid you in identifying
unsafe conditions.
Use good judgment to identify possible safety conditions not covered
by this inspection guide. Refer to the safety reminders for a general
checklist.
If any unsafe conditions exist, find out how serious the hazard could
be and if you can continue before you correct the hazard.
Check the following items:
•
•
•
Damaged, missing, or altered parts, especially in the area of the
On/Off switch and the power supply
Damaged, missing, or altered covers, especially in the area of
the top cover and the power supply cover
Possible safety exposure from any non-Lexmark attachments
Preventive Maintenance 119
4039-1XX
Lubrication Specifications
Lubricate only when parts are replaced or as needed, not on a
scheduled basis. Use of lubricants other than those specified can
cause premature failure. Some unauthorized lubricants may
chemically attack polycarbonate parts. Use IBM no.10 oil PN
1280443 (approved equivalents: Mobil DTE27, Shell Tellus 100,
Fuchs Renolin MR30) to lubricate the areas of contact between:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Gear no. 2 and its stud on the side plate
Gear no. 3 and its stud on the motor bracket
Gear no. 4 and its thrust washer
Gear no. 4 and its stud on the motor bracket
Gear no. 5 and its stud on the motor bracket
Gear no. 6 and its stud on the motor bracket
Gear no. 6 and its thrust washer
Gear no. 7 and its stud on the rail
Gear no. 7 and its thrust washer
Gear no. 8 and its stud on the rail
Gear no. 8 and its thrust washer
Gear no. 9 and its stud on the rail
The metering roller shaft and its bushings on the rail assembly
The main metering backup roller and its stud and thrust washer
The D-roller shaft and its bushings on the rail assembly
The auxiliary metering roller and its stud on the rail, including the
snap-in groove and the snap ridges in the roller hole
•
•
•
•
•
•
•
•
Gear no. 14 and its stud on the rail
Gear no. 13 and its stud on the rail
The auxiliary paper feed idler and its stud on the rail
The prealigner drive idler and its stud on the rail
The prealigner drive roller and its stud on the rail
The prealigner backup roller and its shaft and thrust washer
The fixed-center idler gear in the 500 sheet base and its shaft
The idler gear in the 500 sheet base and its shaft
Use IBM no. 23 grease (approved equivalent Shell Darina 1) to
lubricate:
120 Service Manual
4039-1XX
•
•
•
•
•
•
•
•
•
Front pivot latch studs
Gear no. 8 teeth at gear no. 7 contact points
Gear no. 9 teeth at gear no. 11 contact points
Gear no. 9 teeth at gear no. 8 and gear no. 10 contact points
Cover Hinge Spring tips
Cartridge “ramps” at top center of both sides frames
Latch handle tips
Area of contact between fuser release bail and roll
All release arms areas of contact of fuser solenoid lever.
Use grease, p/n 1329301 to lubricate gear nos. 2,3,4,5,6, and 12.
Use all the grease in the packet. Apply part of the grease, rotate the
gears, and apply the rest. The teeth of gears 3, 4, and 5 should be
completely coated.
Use grease, p/n 1384076 to lubricate:
•
•
[A] Areas of contact between the two shafts and the grounding
spring.
Use grease, p/n 1383586 to lubricate: [B] on the duplex unit.
A
B
Preventive Maintenance 121
4039-1XX
Printhead Window Cleaning Procedure
Do not use cleaning fluids on the printhead window. Do not use a
bare cotton swab. The swab deposits lint on the window.
Note: The printhead window is a coated glass. Do not push too
hard and scratch or break the glass.
1. Remove the print cartridge.
2. Fold a lint free cloth over a cotton swab.
3. Open the shutter.
4. Insert the swab and cloth combination in the printhead window
slot, then slide it left to right several times. Move the swab to a
clean spot on the cloth and repeat the cleaning procedure. Do
this procedure several times to make sure the window is clean.
Cleaning The Transfer Roller
Power off the printer. Power on and let it complete POST. Do this two
to three times.
122 Service Manual
4039-1XX
Scheduled Mechanical Maintenance
The operator panel will display the message “80 Scheduled
Maintenance” at each 200K (100K for 12C) page count interval. It is
necessary to replace the fuser assembly, transfer roller, d-roll, and
lower redrive shaft assembly at this interval to maintain the print
quality and reliability of the printer. These items are available as
individual FRUs. They are also available as a maintenance Kit
through the dealer options ordering channel.
After replacing the kit the maintenance count must be reset to zero
to clear the “80 Scheduled Maintenance” message.
Preventive Maintenance 123
4039-1XX
Parts Catalog
How To Use This Parts Catalog
•
SIMILAR ASSEMBLIES: If two assemblies contain a majority of
identical parts, they are broken down on the same list. Common
parts are shown by one index number. Parts peculiar to one or
the other of the assemblies are listed separately and identified
by description.
•
•
AR: (As Required) in the Units column indicates that the quantity
is not the same for all machines.
NP: (Non-Procurable) in the Units column indicates that the part
is non-procurable and that the individual parts or the next higher
assembly should be ordered.
•
NR: (Not Recommended) in the Units column indicates that the
part is procurable but not recommended for field replacement,
and that the next higher assembly should be ordered.
•
•
•
R: (Restricted) in the Units column indicates that the part has a
restricted availability.
NS: (Not Shown) in the Asm-Index column indicates that the part
is procurable but is not pictured in the illustration.
INDENTURE: The indenture is marked by a series of dots
located before the parts description. The indenture indicates the
relationship of a part to the next higher assembly. For example:
INDENTURE RELATIONSHIP OF PARTS
(No dot) MAIN ASSEMBLY
(One dot) o Detail parts of a main assembly
(One dot) o Subassembly of the main assembly
(Two dot) o o Detail part of a one-dot subassembly
(Two dot) o o Subassembly of a one-dot subassembly
Parts Catalog 124
4039-1XX
Asm-
Index
Part
Number
Units
Description
1-1
-1
1325311
1328204
1329607
1381017
1328207
1328453
1325135
1325136
1325137
1325952
1328511
1419451
1375923
1375925
1375992
1375927
1377417
1325115
1328208
1328210
1328329
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Top Cover 10R/12R/12C/10P
Top Cover 12L/16L
Kit, Stacker Spring 16L
Operator Panel Asm
Door, Top Cover 12L/16L
Screw, Operator Panel
Front Logo, 10R
NS
-1A
-1B
NS
-2
-2
Front Logo, 12R
-2
Front Logo, 12L
-2
Front Logo, 12C
-2
Front Logo, 16L
-2
Front Logo, 10P
-2
Front Logo, 10R plus
Front Logo, 12R plus
Front Logo 12C plus
Front Logo 12L plus
Front Logo 16L plus
Right Cover Asm 10R/12R/12L/12C
Right Cover Asm 10P/16L
Door, Right Cover
-2
-2
-2
-2
-3
-3
-4
NS
Label, Door, Right Cover 10R/12R/12L/12C/
16L
-5
1328186
1195318
1329070
1328473
1
1
1
1
1
1
1
1
1
1
1
1
Front Cover Asm
-6
On/Off Switch Lever
-7
Output Deflector
-8
Output Deflector Lever
Spring, Deflector Lever, Parts Packet 1383316
Spring, On-Off Actuator
Spring, Front Cover Deflector
Left Cover
-9
-10
-11
-12
-14
-14
-15
-16
1058249
1183599
1328185
1325026
1328509
1183536
1183538
Paper Stop Asm,10R/12R/12C/10P
Paper Stop Asm, 12L/16L
Front Exit Slide
Tray, Front Exit with slide
126 Service Manual
4039-1XX
Assembly 1: Covers (Continued)
14
1
1B
2
1A
17
12
10
7
6
5
4
27
8
9
15
11
16
3
Parts Catalog 127
4039-1XX
Asm-
Index
Part
Number
Units
Description
1-17
NS
1328508
1328482
1328189
1
1
Manual Feed Tray with guide
Screw (Deflector Spring Mtg.) Parts Packet
1383314
NS
NS
1
1
Cover, Duplex mtg. slot
Screw (Deflector Switch Mtg. plate) Parts
Packet 1383314
-27
1
Front Exit Door
128 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
2-1
1381120
1
1
Lower Frame Assembly 10R/12R/12L/12C/16L/
10P
-1
1381001
Lower Frame Assembly (16L below serial
number 11-09885 U.S. & 11-10915 W.T.)
-2
-2
-2
-2
1381046
1381047
1381121
1381002
1
1
1
1
Motor, Brkt. and Gear Asm. 10R
Motor, Brkt. and Gear Asm. 12R/12L/12C
Motor, Brkt. and Gear Asm. 16L
Motor, Brkt. and Gear Asm. (16L below serial
number 11-09885 U.S. & 11-10915 W.T.)
-2
-2
1381049
1381122
1
1
Bracket and Gear Asm. 10R (W/O motor)
Bracket and Gear Asm. 12R/12L/12C/16L
(W/O motor)
-2
-2
1381003
1381623
1
1
Bracket and Gear Asm. (W/O motor) (16L
below serial number 11-09885 U.S. & 11-10915
W.T.)
Motor, Brkt. and Gear Asm., 10P - includes
Gear 6
-3
1325614
1329515
1408672
1328503
1328441
1623642
1623642
1328244
1624875
1328243
1039391
1329013
1383316
1383314
1039271
1383314
1622347
1329144
1328245
1408645
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
Plate Asm. Gear Box Mtg. 10R
Plate Asm. Gear Box Mtg. 12R/12L/12C/16L
Plate, Gear Box Mtg. 10P
Screw, Motor Brkt. Mtg. (All except 10P)
Clip, Ground, Motor Mtg. (All except 10P)
Mtg. Screw, motor (All except 10P)
Mtg. Screw, Gear Asm. (All except 10P)
Gear No. 6 (All except 10P)
Mtg. Screw, Gear # 6 (All except 10P)
Gear No. 2
-3
-3
-4
-4A
NS
NS
-5
-5A
-6
-7
Detent, Box
-8
Right Cartridge Latch
-9
Spring, Parts Packet
-10
-11
-12
-13
-14
-15
-15
Washer, Parts Packet
Shaft, Gear 2
Nut, Gear 2, PP
Lockwasher, Gear 2
Left Cartridge Latch
Gear Train Cover (All except 10P)
Gear Train Cover, 10P
130 Service Manual
4039-1XX
Assembly 2: Lower Frame (Continued)
1
7
4A
14
15
10
4
5
2
1
20
22
9
7
8
1
6
18
11
23
3
13
19
9
12
17
Parts Catalog 131
4039-1XX
Asm-
Index
Part
Number
Units
Description
2-17
-17A
-18
-19
NS
1383314
1383314
1328428
1328427
1383314
1039476
1328181
1325282
1408721
1383314
4
2
1
1
1
1
1
1
1
1
Nut, Motor Bracket Parts Packet
Screw, Motor Bracket Parts Packet, 10P
LH Bracket, Duplex
RH Bracket, Duplex
Screw, Duplex Bracket Parts Packet
Grommet, Printhead Cable
Bracket, cover pivot
-20
-21
-22
-23
NS
Cable Clamp
Guide, Cable, 10P
Screw, Cable Clamp Parts Packet
132 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
3-1
1325196
1
1
Cover Hinge Asm 10R/12R/12C/10P (does not
include the load box)
-1
1381045
Cover Hinge Asm 12L/16L (does not include
the load box)
-1A
-2
1383314
1325103
1328218
1328215
1402284
1383315
1039693
1383315
1328220
1039692
1383998
1424481
1328222
1325022
1383315
1383316
1383315
1383314
1383314
1383314
1328307
1325049
1328217
1328308
1325108
1383313
1381004
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
Screw, Cover Hinge Parts Packet
Upper Plate Asm 10R/12R/12C/10P
Upper Plate Asm 12L/16L
Cartridge Load Box 10R/12R/12C/12L/16L
Cartridge Load Box, 10P
Right Cam Button, Parts Packet
Right Bellcrank
-2
-3
-3
-4
-5
-6
Left Cam Button, Parts Packet
Spring, Bellcrank
-7
-8
Left Bellcrank
-9
Fan Asm
NS
-10
-10
-11
-12
NS
-14
NS
-16
-17
-18
-18
-19
-20
-21
-22
Pad, Acoustic (Fan)
Plenum Asm 12R/12L/12C/16L
Plenum Asm 10R/10P
Retainer, Parts Packet
Spring, Parts Packet
Retainer, Parts Packet
Screw, Parts Packet
Washer, Parts Packet
Screw, Plenum Mtg., Parts Packet
Grip, Handle
Handle Latch 10R/12R/12C/10P
Handle Latch 12L/16L
Sleeve
Spring, Handle
Ground Strap, Parts Packet
Output Bin Sensor Assembly (handle
mounted) 12L/16L
-23
-24
-25
1383316
1383315
1383314
1
1
2
Retainer, E-Clip, Parts Packet
Pivot, Handle--Parts Packet
Screw, Parts Packet
134 Service Manual
4039-1XX
Assembly 3: Upper Frame (continued)
1A
1
22
17
18
23
19
23
3
20
23
28
8
29
23
26
14
25
7
11
6
2
12
21
28
16
24
12
4
24
11
5
10
30
Parts Catalog 135
4039-1XX
Asm-
Index
Part
Number
Units
Description
3-26
1381099
1
1
Cable, Output Bin/Operator Panel 12L(handle
mounted sensor)
-26
1381134
Cable, Output Bin/Operator Panel 16L(handle
mounted sensor)
-26
-28
-29
-30
-30
1381095
1383314
1325138
1325067
1328467
1
2
1
2
2
Cable, Operator Panel 12C/12R/10R/10P
Screw, Shaft Mtg., Parts Packet
Spring, Redrive 10R/12R/12C/10P
Spring, Plenum 10R/10P
Spring, Plenum 12R/12L/12C/16L
136 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
4-1
-1
1381624
1381005
1328431
1325017
1325018
1038199
1383315
1383316
1383314
1383314
1383314
1383315
1
1
1
1
1
1
1
1
2
1
1
1
Printhead 10P
Printhead 10R/12R/12C/12L/16L
Printhead Shroud Assembly
Cable, Fan/Mirror Motor
Cable, hsync/Laser
-2
-3
-4
NS
-6
Cable, Tie
Pin, Parts Packet
-7
Spring, Parts Packet
-8
Screw, Printhead Mtg., Parts Packet
Screw, Hex Headed Parts Packet
Pointer, Parts Packet
-8A
-8B
-9
Retainer, Parts Packet
138 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
5-1
-2
-3
-4
-4
-5
-5
-6
-7
1039101
1183597
1381670
1381636
1383430
1039102
1408859
1383315
1328385
1
1
1
1
1
1
1
1
1
Outer Deflector
Upper Deflector
Inner Deflector with Roller
Input Sensor Board 10P
Input Sensor Board 10R/12R/12C/12L/16L
Lower Deflector 10R/12R/12L/16L
Lower Deflector 10P/12C
Flag, Input Sensor, Parts Packet
Right Rail Asm (With Gears) 10R/12R/12C/
12L/16L
-7
1328314
1039170
1328648
1328317
1039175
1042211
1328192
1328193
1039058
1328172
1042205
1328168
1042206
1328169
1042207
1328173
1381073
1328323
1328322
1328321
1383313
1381015
1183244
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
Right Rail Asm (Without Gears)
Machine Pad 10R/12R/12C/10P
Toner Shield
-8
-9
-10
-11
-12
-12
-13
-14
-14
-15
-15
-16
-17
-18
-18
-19
-20
-21
-22
-23
-24
-25
Left Frame
Tray Frame Spring
Belt, Redrive 10R/12R/12C/10P
Belt, Redrive 12L/16L
Belt, Auxiliary 12L/16L
Shaft Asm, Lower Redrive 10R/10P
Shaft Asm, Lower Redrive 12R/12L/12C/16L
Deflector, Redrive 10R/10P/12R/12C
Deflector, Redrive 12L/16L
Shaft Asm, Upper Redrive
Shaft Asm, Auxiliary Shaft 12L/16L
Shaft Asm, Middle Redrive 10R/10P
Shaft Asm, Middle Redrive 12R/12C/12L/16L
Toner Sensor
Shaft 12L/16L
Roller, backup 12L/16L
Spring, backup 12L/16L
Jumper, Ground, Parts Packet
Paper Size Sensor Asm
Arm, Tray Frame
140 Service Manual
4039-1XX
Assembly 5: Paper Feed (Continued)
31
16
37
38
34
36
18
26
2
29
15
28
23
13
12
1
35
17
21
20
14
6
3
22
4
33
19
35
5
34
11
35
39
23
10
8
30
7
23
25
8
24
9
8
Parts Catalog 141
4039-1XX
Asm-
Index
Part
Number
Units
Description
5-27
NS
-28
-28
-29
NS
-30
-31
-33
-34
1328452
1328450
1381617
1381618
1328381
1383314
1183245
1383314
1328298
1328167
1
1
1
1
1
1
1
1
1
1
Deflector, Paper 10R/12R/12C/12L/16L/10P
Spring, Shaft Grd. 12L/16L
Kit, Anti-Squeak Bearing 10P/10R/12R/12C
Kit, Anti-Squeak Bearing 12L/16L
Outer Redrive Shield 12L/16L
Screw Backup Spring Mtg., Parts Packet
Spring, Arm Tray Bias
Screw, Redrive Mtg., Parts Packet
Guide, Fuser Input
Redrive Assembly 12L/16L,With Handle-
Mounted Bin Sensor
-34
1381527
1
Redrive Assembly 12L/16L,With Redrive-
Mounted Bin Sensor
-34
-34
-35
NS
-36
1042230
1325515
1383314
1328345
1381298
1
1
1
1
1
Redrive Assembly 10R/10P
Redrive Assembly 12R/12C
Screw Parts Packet
Spring, Bias, Transfer Housing
Output Bin Sensor 12L/16L, redrive mounted
sensor
-37
-38
1376284
1381567
1
1
Cable, Output Bin/Op Panel 12L/16L, redrive
mounted sensor
Kit, Bail, Minibail, and Guide 12L/16L, redrive
mounted sensor
142 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
6-1
-1
-
1328383
1409238
1
1
1
1
1
1
1
1
1
Bellcrank, Metering 10P/10R/12R/12L/16L
Bellcrank, Metering 12C
o Shaft
-
o Bellcrank
-
o Roll
-
o Thrust Washer
-2
-3
-4
1381145
1039278
1383316
Kit, Prealigner and Metering Rollers
Gear, Idler, Prealigner
Spring, Prealigner and Metering Bellcranks,
Parts Packet
-5
-
1328384
1
1
1
1
1
1
1
1
Bellcrank, Prealigner 10P/10R/12R/12L/16L
o Shaft
-
o Roll
-
o Bellcrank
-
o Thrust washer
-5
NS
NS
1402336
1383580
1383908
Bellcrank, Prealigner 12C
Anchor Repair Kit (Metering)
Anchor Repair Kit (Prealigner)
144 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
7-1
-1
1328311
1408705
1328279
1126832
1328385
1
1
1
1
1
D-Roller Asm 10R/12R/12L/16L
D-Roller Asm, 10P/12C
Washer, Thrust
-2
-3
Clip, D-roll
-4
Rail Assembly, Right (With gears)10R/12R/
12C/12L/16L
-4
-5
-6
1328314
1328313
1328454
1
1
1
Rail Assembly, Right (W/O gears)
Shield, D-Roll
Shaft, D-Roll with Gear 11, 10R/12R/12C/12L/
16L
-6
-7
-8
1408482
1383315
1383316
1
1
1
Shaft, D-Roll with Gear 11, 10P
Bushing, Parts Packet
Spring, Gear Advance Parts Packet 10R/12R/
12C/12L/16L
-9
1383433
1383318
1383318
1
1
1
Clutch Magnet Asm 10R/12R/12C/12L/16L
Gear No. 14, Sheet Feed, Parts Packet
-10
-11
Gear No. 9, Parts Packet 10R/12R/12C/12L/
16L
-11
-12
-13
-14
-15
1408259
1383318
1383318
1383318
1383314
1
1
1
1
1
Gear No. 9, 10P
Gear No. 7, Parts Packet
Gear No. 8, Parts Packet
Gear No. 10, Parts Packet
Screw, Clutch Mag. Mtg., Parts Packet 10R/
12R/12C/12L/16L
-16
1383316
1
Spring, Magnet Arm, Parts Packet 10R/12R/
12C/12L/16L
-17
-18
-19
-20
-21
-22
-23
-24
-25
1383314
1383314
1383315
1383318
1383315
1039170
1381306
1408243
1381663
1
1
1
1
1
1
1
1
2
Washer, Parts Packet 10R/12R/12C/12L/16L
Washer, Thrust, Parts Packet
Bushing, Gear 10, Parts Packet
Gear 13, Parts Packet
Clip, Parts Packet
Machine Pad
Torquer Motor, 10P
Adapter, Torquer Motor, 10P
Screw, Torquer, Parts Packet
146 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
8-
-
1183260
1183276
1183367
1
1
1
Paper Tray Assembly, 11 in. (200-sheet)
Paper Tray Assembly, 14 in. (200-sheet)
-
Heavy Duty Paper Tray Assembly, 11 in. (200-
sheet)
-
1058272
1
Heavy Duty Paper Tray Assembly, 14 in. (200-
sheet)
-
1183376
1183266
1183275
1183163
1408567
1183329
1183330
1039562
1058486
1
1
1
1
1
1
1
1
1
Paper Tray Assembly, A5
11 in. Cover
-1
-1
-2
-3
-4
-4
-5
-6
14 in. Cover
Paper Stop
Corner Buckler
Liner, 11 in.
Liner, 14 in.
Adjustable Guide
Universal Paper Tray Adapter
148 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
9-
1195837
1195831
1183801
1183804
1183357
1183359
1039582
1408851
1408882
1183262
1183298
1183266
1183275
1195835
1383385
1424558
1383385
1383390
1383390
1039597
1383385
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Paper Tray Assembly, 11 in.
Paper Tray Assembly. 14 in.
Bottom Cover 11 in.
Bottom Cover 14 in.
Base 11 in.
-
-1
-1
-2
-2
Base 14 in.
-3
Paper Guide
-4
Slide 11 in.
-4
Slide 14 in.
-5
Paper Stop
-5A
-6
Slider, Paper Stop
Cover 11 in.
-6
Cover 14 in.
-7
Pivot Plate, with label
Retainer, Parts Packet
Spring Assembly
Setscrew, Parts Packet
Thumb Wheel Gear, Parts Packet
Wheel, Parts Packet
Detent Spring
-8
-10
-11
-12
-13
-14
-15
Screw, Parts Packet
150 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
10-1
-2
1328194
1039558
1328197
1039170
1328674
1
1
1
1
1
Housing
Roll
-3
Plate Assembly, Gear
Pad, Machine
Clip, Ground
-4
NS
152 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
11-1
-2
1183342
1328630
1039170
1039596
1383316
1039603
1039540
1383925
1383385
1383385
1383385
1381622
1383316
1039558
1183299
1383314
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Base Assembly
Deflector
-3
Feet
-4
Bellcrank Assembly
Spring, Bellcrank, Parts Packet
Drive Roller
-5
-6
-7
D-Roller Tire
-8
Paper Feed Magnet
Washer, Parts Packet
Screw, Parts Packet
Spring, Parts Packet
Drive Assembly
-9
-10
-11
-12
-13
-14
-15
-16
D-Roller Bias Spring, Parts Packet
Roller
Switch Assembly
Screws, Parts Packet
154 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
12-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-2
-3
1381082
1381083
1381521
1381084
1381085
1381522
1381010
1381038
1381626
1381627
1381679
1381678
1383314
1380785
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Fuser and Lamp 110V 10R
Fuser and Lamp 110V 12R/12L
Fuser and Lamp 110V 12C
Fuser and Lamp 220V 10R
Fuser and Lamp 220V 12R/12L
Fuser and Lamp 220V 12C
Fuser and Lamp 110V 16L
Fuser and Lamp 220V 16L
Fuser and Lamp 110V 10P
Fuser and Lamp 220V 10P
Fuser and Lamp, Low Pressure 110V 10R
Fuser and Lamp, Low Pressure 220V 10R
Screw, Fuser Asm, Parts Packet
Fuser Wiper Assembly (supply item) 10R/12R/
12C/12L/16L
-3
-4
-4
-6
-7
-8
1382287
1039315
1328132
1038717
1383314
1383311
1
1
1
1
1
1
Fuser Wiper Assembly (supply item) 10P
Fuser Cover 10R/10P
Fuser Cover 12R/12L/12C/16L
Spring Redrive Exit
Screw, Parts Packet
Fuser Lamp 110V 10R/12R/12L. Install lamp
with color-coded end away from gear.
-8
-8
-8
-8
-8
1381523
1383324
1381524
1381011
1381037
1
1
1
1
1
Fuser Lamp 110V 12C/10P. Install lamp with
color-coded end away from gear.
Fuser Lamp 220V 10R/12R/12L. Install lamp
with color-coded end away from gear.
Fuser Lamp 220V 12C/10P. Install lamp with
color-coded end away from gear.
Fuser Lamp 110V 16L. Install lamp with color-
coded end away from gear.
Fuser Lamp 220V 16L. Install lamp with color-
coded end away from gear.
156 Service Manual
4039-1XX
Assembly 12: Fuser (Continued)
7
3
7
13
4
2
8
23
1
15
2
15A
8A
9
26
16
6
19
25
22
24
12
11
10
20
21
14
17
18
Parts Catalog 157
4039-1XX
Asm-
Index
Part
Number
Units
Description
12-8A
-8A
-8A
-8A
NS
NS
-9
1381086
1381076
1381146
1383322
1039305
1329928
1381012
1381637
1328458
1376367
1381687
1383315
1039481
1381537
1381155
1039328
1328134
1039311
1381018
1383314
1039251
1328124
1383317
1383316
1328437
1328438
1383314
1039316
1039317
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
Hot Roll Assembly 10R
Hot Roll Assembly 12R/12L/16L
Hot Roll Assembly 12C
Hot Roll Asm, 10P
Backup Roll 10R/12R/12L/16L
Backup Roll, 10P
Thermistor Sensor Asm 10R/12R/12C/12L/16L
Thermistor Sensor Asm, 10P
Redrive Idle Arm Asm, 12R,12L,12C,16L
Redrive Idle Arm Asm, 10R/10P
Paper Exit Bd Asm
-9
-10
-10
-11
-12
-13
-14
-15
-15A
-15A
-16
-17
-18
-19
-19
-20
-21
-22
-23
-24
-25
-26
Flag, Parts Packet
Fuser Power Cable
Cable, Fuser/Front Cover Exit Sensor
Thermal Fuse Asm
Clips, Thermal Fuse 10R/10P
Clips, Thermal Fuse 12R/12L/16L
Bail Handle
Fuser Solenoid Asm 12R/12L/16L
Screw, Fuser Solenoid Mtg., Parts Packet
Gear No. 1, Hot Roll 10R/10P
Gear No. 1, Hot Roll 12R/12L/12C/16L
Gear 18T Redrive, Parts Packet
Spring, Redrive Idler Parts Packet
Contact Asm, Right Lamp
Contact Asm, Left Lamp
Screw, Mtg., Parts Packet
Detack Fingers
Detack Finger springs
158 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
13-1
-1
1383974
1383975
1381014
1381039
1383981
1381643
1381644
1328463
1328464
1035151
1051604
1342514
1
1
1
1
1
1
1
1
1
1
1
1
LV Power Supply 110V 10R/12R/12L/12C
LV Power Supply 220V 10R/12R/12L/12C
LV Power Supply 110V 16L
-1
-1
LV Power Supply 220V 16L
-1
LV Power Supply 100V 10R/12R/12L/12C
LV Power Supply 110V, 10P
-1
-1
LV Power Supply 220V, 10P
NS
NS
NS
NS
-3
Fuse, LVPS SB 12A 110V 16L/10P
Fuse, LVPS 6.3A 220V 16L/10P
Fuse, LVPS SB 10A 110V 10R/12R/12L/12C
Fuse, LVPS 4A 220V 10R/12R/12L/12C
Power Cord Set, U.S./Canada/Mexico/Central
and South America/ Saudi Arabia (LV)/Peru
-3
1342530
1
Power Cord Set, Germany/France/Spain/
Norway/Finland/the Netherlands/Austria/
Belgium/Brazil/Greece/Luxembourg/Portugal/
Sweden/Turkey/Indonesia/ Saudi Arabia (HV)
-3
-3
-3
-3
-3
1342532
1342533
1342534
1342535
1342536
1
1
1
1
1
Power Cord Set, S. Africa
Power Cord Set, Switzerland
Power Cord Set, Chile/Italy
Power Cord Set, Denmark
Power Cord Set, New Zealand/Australia/
Argentina/Paraguay
-3
1342537
1342543
1039467
1058266
1381390
1381645
1381653
1381515
1381517
1381504
1381519
1381578
1408063
1
1
1
1
1
1
1
1
1
1
1
1
1
Power Cord Set, Israel
-3
Power Cord Set, UK/Malaysia/Singapore
Rod, on/off
-4
-4A
-5
Support, Rod on/off
HV Power Supply 10R/12R/12C/12L/16L
HV Power Supply 10P
-5
-5A
-6
Cable, HV Power Supply 10P
System Board 10R
-6
System Board 12R/12L
System Board 12C
-6
-6
System Board 16L
-6
System Board 10P
NS
Cable, Erase Lamps/Input Sensor Board, 10P
160 Service Manual
4039-1XX
Assembly 13: Electronics (Continued)
4A
3
18
4
1
5
5A
18
21
23
11
9
22
6
13
7
Parts Catalog 161
4039-1XX
Asm-
Index
Part
Number
Units
Description
13-7
1328291
1
Cable, HVPS/Input Sensor Board 10R/12R/
12C/12L/16L
-9
1321882
1328589
1325436
1325434
1328337
1419453
1328338
1325106
1328988
1383314
1328969
1325489
1328281
1328280
1195319
1383315
1383315
1383314
1383314
1383513
1039456
1381513
1381484
1381509
1381628
1376388
1376389
1376390
1325197
1328644
1328647
1381097
1
1
1
1
1
1
1
1
1
1
2
4
2
4
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DRAM SIMM 4MB 12R/12L
DRAM SIMM 2MB 10R/10P
Inner EMC Shield 10R/12R/12L/12C
Outer EMC Shield 10R/12R/12L/12C
Inner EMC Shield 16L
-9
-11
NS
-11
-11
NS
-13
-13
NS
NS
NS
NS
NS
NS
NS
NS
NS
-18
-19
-20
-21
-21
-21
-21
-21
-21
-21
-22
-22
NS
-23
Inner EMC Shield 10P
Outer EMC Shield 16L
Guide, Font Card 10R/12R/12L/12C
Guide, Font Card 16L
Washer, Parts Packet
Nut, Card Mtg.
Standoff, Card Gnd, 10R/12R/12L/12C
Standoff, Internal Threads
Standoff, Card Gnd, 16L, External Threads
Standoff, INA or DC to DC, plastic
Standoff, Sys. Bd., plastic, Parts Packet
Standoff, Sys. Bd., plastic, Parts Packet
Screw, HVPS Mtg., Parts Packet
Screw, LVPS Mtg., Parts Packet
Switch On/Off
Switch Pivot
ROM SIMM 10R
ROM SIMM 12R/12L/12C
ROM SIMM 16L
ROM SIMM 10P
ROM SIMM, 10R, 4039 plus
ROM SIMM, 12R/12L, 4039 plus
ROM SIMM, 16L, 4039 plus
Serial cable 10R/12R/12L/12C
Serial cable 16L
Screw, serial cable
DC to DC convertor 10R/12R/12L/12C
162 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
14-1
-2
1381008
1381007
1381652
1
1
1
Roll Asm, Transfer
Housing, Transfer 10R/12R/12C/12L/16L
-2
Housing, Transfer 10P
(“sawtooth” not present on 10P)
1
1
1
1
1
o Rear Lens Asm, Erase
o Front Lens Asm, Erase
o Contact, Transfer Roll
o Lamp Asm, Erase
-3
1328356
Cover, Clip Bearing
164 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
15-1
-2
1381019
1381006
1381020
1326137
1381021
1408906
1408905
1326001
1381023
1381024
1326041
1326042
1326043
1381025
1326113
1038708
1326064
1381033
1381582
1381034
1381035
1381048
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Top Cover Asm (with fan)
Duplex System Card
Bottom Cover
-3
-4
Exit Sensor Cover
-5
Exit Sensor Asm
-6
Bellcrank
-7
Table Cover (Floor)
Paper Stop/Slide
-8
-9
Gear Block Frame Asm
Input Sensor Card
-10
-11
-12
-13
-14
-15
-16
-17
-18
-18
-19
NS
NS
Duplex System Cable
Cable, Stepper Motor
Cable, Sensor
Paper Feed Motor (DC)
Switch Asm Cover Open
Belt Paper Tray
Belt Paper Drive
Tray Asm 300 w/Top Cover 12L/16L
Tray Asm 130 w/Top Cover 10R/12R/10P
Top Cover Paper Tray
Gear Parts Pack
Flag Parts Pack (4)
166 Service Manual
4039-1XX
Asm-
Index
Part
Number
Units
Description
16-
-
1183151
1183966
1183226
1622529
1039615
1383944
1622303
1622536
1183587
1183155
1183160
1328459
1183273
1
1
1
1
1
1
1
1
1
1
1
1
1
Envelope+ Feeder
100-Sheet Auxiliary Feeder
Weight Assembly
Screw
-1
-2
-3
Spring
-4
Magnet Assembly
Washer
-5
-6
Screw, Mtg
-7
Cover, Right
-8
Guide, Large
Latch, Guide
Guide, Small
-8A
-9
-10
Spring, Override Lever (100-Sheet Auxiliary
Feeder Only)
NS
NS
1383934
1383935
1
1
Roller Pack (Envelope+ Feeder Only)
Roller Pack (100-Sheet Auxiliary Feeder Only)
168 Service Manual
4039-1XX
Assembly 17: Options
Asm-
Index
Part
Number
Units
Description
17-2
-3
-4
-5
-6
-7
-8
-9
-10
-
1328586
1328585
1376461
1328589
1321882
1321883
13A0339
13A0340
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1MB Flash SIMM
2MB Flash SIMM
4MB Flash SIMM
2MB DRAM SIMM
4MB DRAM SIMM
8MB DRAM SIMM
4MB DIMM
8MB DIMM
Option Cards
1381050
1402209
1402207
1402208
1402219
1402217
1402218
13A0294
13A0295
13A0296
13A0297
13A0298
1328563
1325231
1329037
1381096
1329498
1425267
1363110
o INA-LocalTalk
-
o INA-Ethernet 10Base2, low memory
o INA-Token Ring, low memory
o INA-Ethernet 10BaseT, low memory
o INA-Ethernet 10Base2, high memory
o INA-Token Ring, high memory
o INA-Ethernet 10BaseT, high memory
o INA-SCS
-
-
-
-
-
-
-
o INA-IPDS
-
o 9 pin-to-Twinax cable, SCS or IPDS
o 9 pin-to-BNC cable, SCS or IPDS
o 9 pin-to-9 pin set up cable
o Screw, INA ground
-
-
-
-9
-10
-11
-12
-
Font Card Adapter 10R/12R/12L/12/C
Font Cartridge Adapter 16L
DC to DC Network Power Card
Hard Disk, 40MB, 16L
Hard Disk, 40MB, 10P
Serial Adapter, 10P
13
Parts Catalog 169
4039-1XX
Assembly 18: Miscellaneous
Asm-
Index
Part
Number
Units
Description
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1319128
1329048
1383313
1383314
1383315
1383316
1383317
1383318
1381145
1383385
1383390
1329301
1384076
1383586
9900692
1280443
1381035
1381048
1381963
1381964
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Parallel Wrap Plug
Serial Wrap Plug
Cables/Jumpers parts packet
Fasteners parts packet
Clips parts packet
Springs parts packet
Gears (1-6) parts packet
Gears (7-14) parts packet
Metering and Prealigner rolls parts packet
Paper Tray parts packet
Paper Tray parts packet
Grease, 2g
Grease, conductive 1 oz.
Grease, damping, 1 oz.
Grease, IBM #23
Oil, IBM #10 4 oz.
Duplex Gears parts packet
Duplex Flags parts packet
Twinax/serial debug cable
Coax/serial debug cable
170 Service Manual
4039-1XX
Index
duplex feed 1 test 36
duplex feed 2 test 37
Numerics
100-sheet auxiliary feeder
paper restraint spring
bottom cover/entry sensor card
problems 18
system card and motor removal
100
A
abbreviations 4
auto clean 34
auto clean delay 34
B
banding 13
envelope enhance 38
envelope print test 38
Envelope+ feeder adjustments
error codes 5
error log 38
ESD-sensitive parts 51
exit sensor removal 85
black page 15
blank page 16
blurred or fuzzy print 17
C
connector locations 101
covers
assembly 125
D
F
defaults 35
grouped 33
diagnostics mode 32
disk test/clean 35
drive motor removal 68
Index 171
4039-1XX
frame
lower frame assembly removal
81
fuser
lubrication specifications 120
920,921, or 922 error 20
drive gear backlash adjustment
54
thermistor removal 76
fuser temperature 39
fuser theory 20
network
connections and checks 46
network card
977 errors 23
G
problems 24
H
removal 84
honeycomb 21
operator panel/output bin sensor
horizontal void or streak 22
114
redrive-mounted outbin sensor
115
I
input sensor removal 80
assembly 169
available 2
L
LAN
information 47
problems 22
LCD test 41
light print 22
output bin sensor 23
172 Service Manual
4039-1XX
diagnosis 27
removal 89
P
page count 41
paper drawer
153
paper feed
assembly 139
drive assembly 145
base printer 25
regularly spaced marks 29
removals 62
paper feed test 41
paper size
switch removal 88
paper tray
(500-sheet) assembly 149
147
scheduled mechanical
110
print test 2 43
print test 3 44
removal 90
print test page 42
system cable
printer ground strap locations 117
locations 105
removal 92
Index 173
|
Lexmark X6575 User Manual
Mitsubishi Electronics Split Type Heat Pump Air Conditioners Pmfy P12nbmu E User Manual
Philips Tea1104 User Manual
Samsung Awt18f1me User Manual
Sears 9 50524 User Manual
Soleus Air Air Conditioner Hgw 308r W User Manual
Soleus Air Pa1 12r 32 User Manual
Subaru Sti Timing Belt User Manual
Toshiba Air Conditioner Ras B10skvp E User Manual
Windchaser Products Pacr9s User Manual