BitStorm 4800 Express Model 4821-A2
Installation Guide
March 2006
Document Part Number: 4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
End User License Agreement (Zhone and Affiliates)
Restrictions. The Software may not be (a) Used on or from any system other
than the System; (b) Used with more than any maximum number of
subscribers stated in the documentation accompanying the Software; (c) Used
so as to circumvent any technological measure included therein or provided
by Zhone from time to time to control access to or limit use of the Software;
(d) sublicensed, rented, leased or lent to third parties; (e) imported or exported
into any jurisdiction except in compliance with all applicable laws of the
United States and such jurisdiction; (f) transferred to a third party unless (A)
User transfers the original and all surviving copies to a third party who has
agreed in writing to be bound hereby and (B) such third party pays to Zhone
such reasonable additional fee as Zhone may impose from time to time with
respect to such transfer; or (g) made available to third parties as part of any
time-sharing or service bureau arrangement. User shall not have the right to
use the Software or any portion thereof for a use other than that contemplated
by its documentation. User will not copy all or any part of the Software or
attempt, or encourage or permit any third party, to modify, adapt, make
derivative works from, reverse engineer, reverse compile, disassemble or
decompile the Software or any portion thereof except and only to the extent
that such activity is expressly permitted by law notwithstanding this
limitation. Violation of any of the foregoing shall be deemed a material breach
hereof. User may make a reasonable number of copies solely for archival or
disaster recovery and subject to the restrictions imposed by copyright law, but
may not modify or otherwise copy the Software. User agrees to reproduce
product identification, copyright and other proprietary notices of Zhone and
Licensors on all copies. User's rights are only as expressly stated herein.
Zhone may immediately terminate your rights if you violate the provisions
hereof.
Limited Warranty. Zhone warrants that the media containing the Software is
free from defects in material and workmanship for ninety (90) days following
your purchase of the Software. You may provide written notice of such defect
(addressed to Zhone Technologies, Inc., Attention: Customer Service, 7001
Oakport Street @ Zhone Way, Oakland, CA 94621) no later than ten (10) days
following expiration of such period and, as your sole and exclusive remedy,
Zhone will provide replacement media. NEITHER ZHONE NOR ITS
LICENSORS MAKE ANY OTHER WARRANTY, EXPRESS, IMPLIED
OR STATUTORY. ZHONE AND ITS LICENSORS DISCLAIM ALL
WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE,
MERCHANTABILITY AND NON-INFRINGEMENT. Some states or other
jurisdictions do not allow the exclusion of implied warranties on limitations
on how long an implied warranty lasts, so the above limitations may not apply
to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from one state or jurisdiction to another.
Limit of Liability. In case of any claim hereunder or related to the Software,
neither Zhone nor its Licensors shall be liable for direct damages exceeding
the price paid by User for the Software or for special, incidental,
consequential or indirect damages, even if advised in advance of the potential
thereof.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
U.S. Government Users. The Software is a "commercial item" as defined at
48 C.F.R. 2.101, consisting of "commercial computer software" and
"commercial computer software documentation" as such terms are used in 48
C.F.R. 12.212. Under 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 to
227.7202-4, U.S. Government Users acquire the Software only with the rights
set forth therein.
Third Party Licensors. This Zhone End User License Agreement may be
accompanied by differing or additional provisions applicable to portions of
the Software provided by one or more Licensors ("Licensor Provisions").
User acknowledges and agrees that its Use of such portions of the Software is
subject to the Licensor Provisions.
!
Important Safety Instructions
1 Read and follow all warning notices and instructions marked on the
product or included in the manual.
2 This product is intended to be used with a 3-wire grounding type plug —
a plug that has a grounding pin. This is a safety feature. Equipment
grounding is vital to ensure safe operation. Do not defeat the purpose of
the grounding type plug by modifying the plug or using an adapter. Prior
to installation, use an outlet tester or a voltmeter to check the AC
receptacle for the presence of earth ground. If the receptacle is not
properly grounded, the installation must not continue until a qualified
electrician has corrected the problem.
If a 3-wire grounding type power source is not available, consult a
qualified electrician to determine another method of grounding the
equipment.
3 Slots and openings in the cabinet are provided for ventilation. To ensure
reliable operation of the product and to protect it from overheating, these
slots and openings must not be blocked or covered.
4 Do not allow anything to rest on the power cord and do not locate the
product where persons will walk on the power cord.
5 Do not attempt to service this product yourself, as it will void the
warranty. Opening or removing covers may expose you to dangerous high
voltage points or other risks. Refer all servicing to qualified service
personnel.
6 General purpose cables are described for use with this product. Special
cables, which may be required by the regulatory inspection authority for
the installation site, are the responsibility of the customer. To reduce the
risk of fire, use a UL Listed or CSA Certified, minimum No. 26 AWG
(0.128 mm2) telecommunication cable, or comparable cables certified for
use in the country of installation.
7 When installed in the final configuration, the product must comply with
the applicable Safety Standards and regulatory requirements of the
country in which it is installed. If necessary, consult with the appropriate
regulatory agencies and inspection authorities to ensure compliance.
4
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
End User License Agreement (Zhone and Affiliates)
8 A rare phenomenon can create a voltage potential between the earth
grounds of two or more buildings. If products installed in separate
buildings are interconnected, the voltage potential may cause a hazardous
condition. Consult a qualified electrical consultant to determine whether
or not this phenomenon exists and, if necessary, implement corrective
action prior to interconnecting the products.
9 In addition, if the equipment is to be used with telecommunications
circuits, take the following precautions:
— Never install telephone wiring during a lightning storm.
— Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
— Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
— Use caution when installing or modifying telephone lines.
— Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
— Do not use the telephone to report a gas leak in the vicinity of the
leak.
10 CLASS 1 LASER PRODUCT: This product has provisions for the
customer to install a Class 1 laser transciever, which provides optical
coupling to the telecommunication network. Once a Class 1 laser product
is installed, the equipment is to be considered to be a Class 1 Laser
Product (Appareil à Laser de Classe 1). The customer is responsible for
selecting and installing the laser transciever and for insuring that the Class
1 AEL (Allowable Emission Limit) per EN/IEC 60825 is not exceeded
after the laser transponders have been installed. Do not install laser
products whose class rating is greater than 1. Refer to all important safety
instructions that accompanied the transciever prior to installation. Only
laser Class 1 devices, certified for use in the country of installation by the
cognizant agency are to be utilized in this product.
11 The equipment is intended for installation in a max. 50° C ambient
temperature, in an environment that is free of dust and dirt.
12 The power supply cord for countries other than North America is to be a
minimum H05 V V-F type, min. 0.75 mm2, 2-conductor and earth ground
terminated in an IEC 320 connector on one end, and a plug which is
certified for use in the country of installation at the other end.
13 Do not physically stack more than eight (8) 26x1 units high. Physical
stability has not been evaluated for stacking higher than eight units, and
any configuration greater than eight may result in an unstable (tip-over)
condition. Ensure that the four (4) rubber feet supplied with the product
have been installed on the bottom of each unit prior to stacking any 26x1
units on top of one another.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EMI Notices
!
UNITED STATES – EMI NOTICE:
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own
expense.
The authority to operate this equipment is conditioned by the
requirements that no modifications will be made to the equipment
unless the changes or modifications are expressly approved by
Paradyne Corporation.
If the equipment includes a ferrite choke or chokes, they must be
installed per the installation instructions.
!
CANADA – EMI NOTICE:
This Class A digital apparatus meets all requirements of the
Canadian interference-causing equipment regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
réglement sur le matérial brouilleur du Canada.
6
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
End User License Agreement (Zhone and Affiliates)
Notices to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry Canada Terminal
Equipment Technical Specifications. This is confirmed by the registration
number. The abbreviation IC before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating
that Industry Canada technical specifications were met. It does not imply that
Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal
equipment is labeled on the equipment. The REN assigned to each terminal
equipment provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed five.
When the equipment is used in a customer premises environment, a Model
6051 POTS Splitter must be used to ensure CS-03 compliance. Refer to the
POTS splitter installation instructions for details.
CE Marking
When the product is marked with the CE mark on the equipment label, a
supporting Declaration of Conformity may be downloaded from the Zhone
Japan
Class A ITE
This is a Class A product based on the standard of the Voluntary Control
Council for interference by Information Technology Equipment (VCCI). If
this equipment is used in a domestic environment, radio disturbance may
arise. When such trouble occurs, the user may be required to take corrective
actions.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
End User License Agreement (Zhone and Affiliates)........................2
Document Purpose and Intended Audience ......................................11
Related Product Documents ................................................................12
Chapter 1- Installation .............................................................................................................13
Overview ................................................................................................13
Preparation .............................................................................................14
Cables Required ....................................................................................15
Unpacking the Hardware......................................................................16
Package Contents ..................................................................................16
Mounting Configurations ....................................................................17
Mounting Brackets................................................................................17
Installing the Brackets for Rack Mounting........................................17
Installing the BitStorm 4800 Express Into a Rack ...........................19
Installing the BitStorm 4800 Express on a Wall...............................21
Chapter 2- Cabling ....................................................................................................................25
Cabling Overview .................................................................................25
DSL Ports...............................................................................................26
10/100BaseT Uplink (Port 2) ..............................................................27
Management Port ..................................................................................28
Console Port...........................................................................................29
Ground....................................................................................................31
Connecting to Power.............................................................................32
Chapter 3- LEDs .........................................................................................................................33
LED Locations.......................................................................................33
LED Meanings.......................................................................................34
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4- Configuration .......................................................................................................35
Overview ................................................................................................35
Using the CLI .......................................................................................36
Startup Procedure for Inband Management.......................................40
Startup Procedure for Out-of-Band Management.............................40
Using the Web Interface.......................................................................41
System / Users .......................................................................................41
Configuration / Management / SNMP ...............................................42
Chapter A- Connectors and Pin Assignments ..............................................................43
Overview ................................................................................................43
Port 1 and Port 2 10/100BaseT Connectors ......................................45
Console Port Connector .......................................................................46
Chapter B- Equipment List ....................................................................................................47
Chapter C- Technical Specifications .................................................................................49
Index......................................................................................................................................................51
10
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THIS GUIDE
Document Purpose and Intended Audience
This document is written for technicians who install the BitStorm® 4800
Express Model 4821-A2 IP DSLAM.
Document Summary
Section
Description
Describes the physical installation of the
BitStorm 4800 Express into a rack.
Describes how to install all cables for the
BitStorm 4800 Express.
Explains the meaning and usage of the front
panel LEDs.
Describes the minimal configuration steps
required to prepare the BitStorm 4800 Express
for remote access, using the command line
interface and web interface.
Appendix A-,
Provides pinouts for connectors on the BitStorm
4800 Express.
List Express and related products.
BitStorm 4800 Express.
Lists key terms, acronyms, concepts, and
sections in alphabetical order.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Product Documents
Documentation for the BitStorm 4800 Express IP DSLAM is available on the
Document Title
BitStorm 4800 Express Model 4821-A2 Command Line Interface Reference
Describes the Command Line Interface (CLI) used to configure and
monitor the BitStorm 4800 Express.
BitStorm 4800 Express Model 4821-A2 SNMP Reference
Contains the information necessary to use Simple Network Management
Protocol (SNMP) to configure and monitor the BitStorm 4800 Express.
BitStorm 6051 POTS Splitter Installation Instructions
Describes how to install the BitStorm 6051 POTS splitter.
Hotwire 6210-A2, 6211-A2, and 6381-A2 User’s Guide
Describes the installation and operation of the 6210 ADSL bridge, 6211
ADSL router, and 6381 ADSL/R router.
GrandVIEW EMS User’s Guide
Contains instructions for maintaining network services and resources using
the GrandVIEW Element Management System (EMS).
12
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Overview
The BitStorm® 4800 Express is a stackable IP DSLAM designed for
installation in a Central Office (CO), multi-tenant unit (MTU), or
multi-dwelling unit (MDU) environment.
C
O
N
S
O
L
P
O
0
E
R
0
T
B
1
1
/1
0
P
O
0
T
R
0
T
B
2
T
1
/1
0
T U S
A
S T
A L A R M
T E S T
1
3
5
7
9
11
12
13
14
15
16
17
18
19
20
21
22
23
24
2
25
26
4
27
28
6
29
30
8
31
32
10
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
D
S
P
O
R
T
1
-2
4
-4
P
2
04-17534
The BitStorm 4800 Express is interoperable with the Hotwire 6381 ADSL/R
modem, as well as any standard ADSL CPE.
A Command Line Interface (CLI) and a web browser interface are provided.
The unit also may be managed using a network manager such as the Paradyne
GrandVIEW™ Element Management System (EMS).
BitStorm 4800 Express IP DSLAM models and features are listed in Table 1,
BitStorm 4800 Express Models and Features.
Table 1:
BitStorm 4800 Express Models and Features
Number of
Model Number
Type
Ports
4821-A2-417
ADSL
12
4821-A2-427
4821-A2-447
ADSL
ADSL
24
48
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Preparation
Consider the following before installing the BitStorm 4800 Express IP
DSLAM:
z
Installation Site
Your installation site should be well ventilated, clean, and free of
environmental extremes.
z
Installation Options
The BitStorm 4800 Express may be:
— Mounted with the included mounting brackets in a standard 19-inch
(483 mm) or 23-inch (584 mm) rack (including both Bay Networks
and Nortel 23-inch racks), or, with separately purchased mounting
brackets, in a 21-inch (535 mm) ETSI rack. ETSI brackets are
As many BitStorm 4800 Express units may be mounted in a standard
rack as there are 1.75-inch (44.45 mm) spaces in the rack, so long as
adequate cooling is provided.
— Mounted vertically against a wall.
The standard mounting brackets provided can be fastened to the base
of the unit for wall mounting.
— Set on a shelf or desktop.
Up to five BitStorm 4800 Express units may be stacked on a shelf or
desktop.
z
z
Power
The BitStorm 4800 Express operates from a 90 to 265 VAC, 47 to 63 Hz
power source.
Cabling
No cable except the power cable is provided with the BitStorm 4800
Express. See Table 2, Cable Descriptions, to determine what cables you
need to procure before installation.
14
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Cables Required
Cables Required
Table 2 shows all the cables that may be required for your installation.
Table 2:
Cable Descriptions
Connector
Name
Connector and Cable
For Connecting . . .
DSL PORTS
1–24
50-pin RJ21X Telco-type
straight connector and
50-wire cable. Two cables
Up to 24 DSL ports per
cable to a POTS splitter.
DSL Ports 25–48 required for 48-port model.
(if installed)
Port 2
10/100BaseT
8-position modular plug
and 8-wire Category 5 or
better unshielded twisted
pair (UTP) cable.
The BitStorm 4800
Express to a network.
Port 1
10/100BaseT
8-position modular plug
and 8-wire Category 5 or
better unshielded twisted
pair (UTP) cable.
A Network Management
System (NMS) over a
Local Area Network
(LAN) employing
10BaseT or 100BaseT.
CONSOLE
DB9 plug connector and
shielded cable.
The BitStorm 4800
Express to one of the
following:
z
The other connector
depends on the serial
port on your terminal or
PC, but normally is a
DB9 socket.
z
z
A terminal or a PC
with a terminal
emulation program, or
z
The other connector
depends on the serial
port on your modem, but
normally is a DB25 plug.
A null modem
A modem.
(crossover) cable is
required.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Unpacking the Hardware
HANDLING PRECAUTIONS FOR
STATIC-SENSITIVE DEVICES
!
This product is designed to protect sensitive components from
damage due to electrostatic discharge (ESD) during normal
operation. When performing installation procedures, however, take
proper static control precautions to prevent damage to equipment. If
you are not sure of the proper static control precautions, contact your
nearest sales or service representative.
The BitStorm 4800 Express is shipped in a cardboard shipping container.
Carefully remove the unit from its shipping container and check for physical
damage. If the unit shows signs of shipping damage, notify your sales
representative.
Package Contents
In addition to this installation guide, the BitStorm 4800 Express shipping
carton should contain:
z
z
z
BitStorm 4800 Express DSLAM
AC Power Cable
Two sets of mounting brackets: one set suitable for a 19-inch (483 mm)
rack and one set suitable for a 23-inch (584 mm) rack (including Bay
Networks and Nortel)
z
Hardware kit
If anything is missing, notify your sales representative.
Before installing the BitStorm 4800 Express, read the Important Safety
Instructions in the beginning of this document.
16
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Configurations
Mounting Configurations
Three basic installation configurations are available:
z
z
z
Rack mount – see Installing the Brackets for Rack Mounting on page 17
Shelf or desktop – see Installing the BitStorm 4800 Express on a Shelf or
Mounting Brackets
Your BitStorm 4800 Express can be installed in a rack or on the wall using
mounting brackets. Two brackets suitable for a 19-inch (483 mm) rack
(marked EIA-19) and two brackets suitable for a 23-inch (584 mm) Bay
Networks or Nortel rack (marked with Paradyne Part Number
868-6282-0020) are shipped with the unit. Two brackets suitable for a 21-inch
(535 mm) rack (marked ETSI) are available from Paradyne as a separate
Rack-mounting brackets may also be used to attach the unit to a wall.
NOTE:
In this guide, the term rack refers to any rack, cabinet, frame, or bay
suitable for mounting telecommunications equipment.
Installing the Brackets for Rack Mounting
To install the mounting brackets for rack mounting:
1 Locate the black screw nearest the front panel on each side of the unit, as
shown.
C
O
N
S
O
LE
P
O
R
T1
10
/1
00
PO
B
R
T
B
T
2
10
/1
00
T
S
U
T
A
T
S
A L A R M
T E S T
1
3
5
7
9
11
1
13
14
15
16
17
18
19
20
21
22
23
24
2
25
26
4
6
27
28
2
9
8
31
32
10
33
34
2
35
36
37
38
39
40
41
42
43
44
45
4
47
48
30
6
D
S
L
P
TS
1
4
D
S
04-17525
2 Remove these two black screws (one from each side) before attempting to
install the mounting brackets.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3 Identify six flat-head screws (for 19-inch racks) or six machine screws
(for 23-inch racks) provided with the mounting brackets in the hardware
kit.
4 Attach the brackets appropriate to your rack size. Tighten all screws
firmly.
19-inch (483 mm) Rack Mount
23-inch (584 mm) EIA and Bay Networks
Rack Mount
21.1-inch (535 mm) Rack Mount
23-inch (584 mm) Nortel
Rack Mount
02-17324
18
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the BitStorm 4800 Express Into a Rack
Installing the BitStorm 4800 Express Into a Rack
Two types of mounting screws are provided. Use:
z
z
#10-32 mounting screws for rails with threaded screw holes
#12-24 mounting screws and self-retaining nuts for rails with unthreaded
screw holes
To install the BitStorm 4800 Express into a rack:
1 Determine where in the rack you will mount the BitStorm 4800 Express.
If your rack does not have threaded screw holes, slip self-retaining nuts
onto the rails where the BitStorm 4800 Express will be fastened.
02-17070
2 Place the unit so that the brackets rest against the front of the rails. Insert
screws in the bottom screw positions and hand-tighten them.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3 Insert and tighten the screws in the top screw positions, then tighten the
bottom screws.
C
O
N
S
O
LE
PO
00
R
T
BT
1
10/1
P
O
RT
B
2
T
10
/10
0
T
A
S
S
A
A
T
ST
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
1
1
7
19
20
21
22
23
24
25
26
27
28
29
30
3
3
1
33
34
3
5
10
37
38
39
40
4
4
1
43
44
8
45
46
47
48
2
36
2
D
S
L
P
O
R
T
S
1
-2
4
D
S
L
P
R
T
S
2
48
PORT1-10/100BT
PORT2-10/100BT
1000BT
PORT3
K
T
GigE
C
S
T
R
T
CONSOLE
T
S
L
A
S
E
P
O
T
S
1
-
2
4
ALARM
1
2
3
4
5
6
7
8
9
1
1
13 15 17 19 21 23
20 22 24
1
0
1
2
1
4
1
6
18
D
S
L
P
O
R
T
S
1
-
2
4
04-17526
20
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the BitStorm 4800 Express on a Wall
Installing the BitStorm 4800 Express on a Wall
Wall mounting requires two wood screws suitable for the weight of the fully
cabled unit. These are not included. Use at a minimum 1/4-inch (6 mm)
diameter screws in 3/4-inch (19 mm) plywood (not drywall).
To install the BitStorm 4800 Express on a wall:
1 Identify the 6-32 x 3/16-inch flat-head screws provided in the hardware
kit and the brackets suitable for a 23-inch rack. Two screws are required
for each bracket.
2 Orient the unit so that the bottom is facing you and the faceplate is at the
top.
3 Locate the supplied Right Side mounting bracket and fasten it to the right
side of the unit.
05-17634
4 Locate the supplied Left Side mounting bracket and fasten it to the left
side of the unit.
5 Tighten all screws firmly.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
6 Install two wood screws (not provided) at the same height above the floor
and 18.75 inches (476.25 mm) apart. Do not completely tighten the
screws. Leave them so their heads are about 1/4 inch (6 mm) from the
wall.
17.85 in (453 mm)
04-17528
7 Hang the unit from the wood screws to verify that the screws are properly
placed. The screws should freely slide into the top of the key slots in the
brackets.
Do not fasten the unit to the wall until after it is completely cabled and
tested.
22
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the BitStorm 4800 Express on a Shelf or Desktop
Installing the BitStorm 4800 Express on a Shelf or
Desktop
If the BitStorm 4800 Express will be placed on a shelf or desktop, install the
provided rubber feet before putting the unit in position.
To install the BitStorm 4800 Express on a shelf or desktop, as a standalone
unit or in a stack:
1 Locate the rubber feet in the hardware kit provided with the unit.
2 Turn the unit upside down on a work surface. Squares stamped into the
bottom of the unit show the proper positions for the feet.
3 Remove the protective sheet from the bottom of each foot, then press the
foot onto a corner of the bottom of the unit.
03-17439
4 Turn the unit right side up and place it in position on a shelf or desktop.
If the installation includes more than one unit, one can be stacked atop
another. Up to five units can be stacked together.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
24
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLING
Cabling Overview
The BitStorm 4800 Express has a large variety of possible cabling
configurations. This chapter describes all possible connections, not all of
which are required:
z
z
z
z
z
z
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabling
DSL Ports
The BitStorm 4800 Express DSL connector supports the tip and ring
connections of up to 24 DSL ports over a 50-position cable. There are two
DSL connectors on the 48-port model.
You must connect the unit to a separate POTS splitter. The Model 6051 POTS
Splitter must be used for customer premises applications in Canada.
To cable the DSL Ports:
1 Insert a cable tie (provided) through the top of the anchor mount next to
the DSL PORTS 1–24 connector.
2 If the connector for your cable has a short captive screw, attach the cable
to the DSL PORTS 1–24 connector and fasten it to the jack screw with its
short captive screw.
#4-40
Jack Screw
Anchor
Mount
Short
Screw
50-Pin
Connector
02-17083
3 If the connector for your cable has a long captive screw, remove the
provided jack screw from the threaded hole next to the DSL PORTS 1–24
connector. Attach the DSL PORTS 1–24 connector to the unit using the
long, captive pan-head screw (provided).
Anchor
Mount
Long
Screw
50-Pin
Connector
02-17346
4 Tighten the cable tie around the connector and trim the excess.
02-17084
DSL Ports 25–48 for DSL PORTS 1–24.
26
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100BaseT Uplink (Port 2)
6 Secure the cables as required for strain relief.
10/100BaseT Uplink (Port 2)
Port 2 is the uplink for the DSLAM. A straight-through cable can be used
regardless of the destination interface, since the port automatically
distinguishes between an MDI and an MDIX.
To use Port 2 as the uplink:
1 Connect an 8-position modular cable to Port 2.
2 Connect the other end of the cable to the uplink interface, such as an
Ethernet switch.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabling
Management Port
Port 1 can be used to connect the BitStorm 4800 Express to a network
management system using a 10BaseT or 100BaseT LAN. A straight-through
cable can be used regardless of the destination interface, since the port
automatically distinguishes between an MDI and an MDIX.
To use Port 1 as the out-of-band management port:
1 Connect an 8-position modular cable to Port 1.
2 If the BitStorm 4800 Express is in a rack, fasten the cable to a rail with a
cable tie.
3 Connect the other end of the cable to your Ethernet switch or a network
interface card in a PC.
Ethernet Switch
CONSOLE
POR
T1
10/100BT
POR
T2
10/100BT
TUS
A
ST
ALARM
TEST
1
2
3
4
5
6
7
8
9
11
1
3
1
1
5
1
1
7
1
9
2
2
1
2
3
2
5
2
7
2
3
9
3
1
3
3
1
0
1
3
5
2
1
3
7
4
3
4
6
9
4
8
1
2
4
3
0
4
2
5
2
4
7
4
2
6
2
8
0
3
2
3
4
3
6
3
8
0
4
2
4
4
4
6
4
8
DSL
POR
TS 1-24
04-17529
Port 1
28
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Port
Console Port
The CONSOLE port normally serves as the primary user interface with the
BitStorm 4800 Express during installation. You can connect a terminal or PC
directly to the CONSOLE port using a DTE cable (see procedure below). You
can also use the CONSOLE port to attach a modem to the BitStorm 4800
Express for remote dial-in management of the unit using a DCE cable (see
Connecting a Terminal or PC to the Console Port
To connect a terminal or PC to the CONSOLE port:
1 Configure the terminal or terminal emulation program to use the
following parameters:
— Speed: 9600 bps
— Data bits: 8
— Parity: None
— Flow Control: None
— Stop bits: 1
2 Determine and procure the proper Data Terminal Equipment (DTE) cable
type. The CONSOLE port requires a DB9 plug connector. The other
connector depends on the serial port on your terminal or PC.
3 Connect the DB9 plug connector to the CONSOLE port socket. The
CONSOLE port is ordinarily used only during installation, so do not
fasten the connector.
4 Connect the other end of the cable to the serial port of your terminal or
PC.
Serial
Port
C
O
N
S
O
L
P
O
0
E
R
0
T
B
1
T
1
/1
0
PO
R
0
/1
T
2
T
1
0
0
B
S
U
M
T
R
T
A
A
S
T
L
E
S
A
T
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
10
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
D
S
L
P
O
R
T
S
1
-2
4
04-17530
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabling
Connecting a Modem to the Console Port
To connect a modem to the CONSOLE port:
1 Determine and procure the proper DCE cable type for your modem. The
CONSOLE port requires a DB9 plug connector. The other connector
depends on the serial port on your modem, but normally a DB25 plug is
required. The cable must be an EIA-232-E crossover (null modem) cable.
2 Connect the DB9 plug connector to the CONSOLE port socket.
3 If the modem will be permanently connected, fasten the connector to the
Management Module with its captive screws. If the BitStorm 4800
Express is in a rack, dress the cable to the left and attach it to the rail with
a cable tie.
4 Connect the other end of the cable to the serial port of your modem.
Serial Port
Modem
PW
R
ALM
TS
T
LIN
E
ETH
ER
NE
T
CONSOLE
POR
T1
10/100BT
POR
T2
10/100BT
TUS
T
A
ST
ALARM
TES
1
2
3
4
5
6
7
8
9
11
1
3
1
5
1
7
1
9
2
1
2
3
2
5
2
7
2
9
3
3
1
1
3
3
0
1
2
3
5
3
3
1
4
7
1
6
3
9
1
8
4
1
2
0
4
3
2
2
4
5
2
4
4
7
2
6
2
8
3
0
2
3
4
3
6
8
4
0
4
2
4
4
4
6
4
8
DSL
POR
TS 1-24
CONSOLE
Port
04-17531
30
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Ground
Ground
To connect the unit to a ground:
1 Crimp a ring terminal onto the stripped end of 14 AWG or heavier copper
ground wire.
2 Remove the screw marked by the ground symbol (
) at the right side
of the front panel.
3 Fasten the ring terminal to the front panel using the same screw.
4 Attach the ground wire to an earth ground.
D
SL
PO
R
TS 25-48
To Earth Ground
04-17532
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabling
Connecting to Power
The BitStorm 4800 Express can be powered by any AC power source
supplying 90–265 VAC at 47–63 Hz.
To connect the BitStorm 4800 Express to a power source:
1 Insert the supplied power cord into the power socket on the back of the
unit.
02-17248
2 If the BitStorm 4800 Express is in a rack, dress the power cord to the left
and fasten it to the rail with a cable tie.
3 Connect the other end of the power cord to a grounded AC power source.
4 Make sure the STATUS LED on the front panel is ON (green). See
32
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
LEDS
LED Locations
The locations of the System and DSL Port LEDs on the front panel of the
BitStorm 4800 Express are shown in Figure 1, Front Panel LEDs.
Link LEDs
Activity LEDS
DSL Ports LEDs
PORT1
10/100BT
PORT2
10/100BT
CONSOLE
1
2
3
4
5
6
7
8
9
11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47
10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48
04-17533
CO
NS
OL
E
PO
RT
1
T
10
/10
0B
P
OR
T2
0B
10
/10
T
S
U
T
A
T
S
A L A R M
T E S T
1
3
5
7
9
1
1
13
14
15
16
17
18
19
20
21
22
23
24
2
25
26
4
6
27
28
29
30
8
31
32
10
33
34
12
35
36
37
38
39
4
41
4
3
4
5
47
48
0
4
2
4
4
4
6
L
P
OR
T
-
1-2
4
D
25
-48
Figure 1: Front Panel LEDs
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
33
Download from Www.Somanuals.com. All Manuals Search And Download.
LEDs
LED Meanings
When power is first applied to the unit, it performs a power-on self-test. When
this test is successfully completed, the Status LED blinks. The meaning of all
Table 3:
LED
Front Panel LEDs
Color State
Meaning
Link*
Green Off
On
No Ethernet link present.
Ethernet Link present.
Flashing Ethernet link is present, but port is
administratively disabled.
Activity*
STATUS
Green Off
No data is being transferred.
Data is being transferred.
On
Green Off
No power, or the unit has not
completed initialization.
On
Unit has power and has completed
initialization.
ALARM
TEST
Amber Off
On
No Alarms.
Unit failed self-test, or the unit has
exceeded a safe temperature, or a fan
has failed.
Amber Off
On
Normal operating mode.
At least one port is in test mode.
DSL Ports
(LEDs
Green Off
The port is disabled or no signal is
detected on the line.
numbered
On
Port has successfully trained with the
remote and is active.
1–24 or 1–48
correspond to
DSL ports
1–24 or 1–48)
* The RJ45-type connectors for Port 1 and Port 2 bear two LEDs: the left one is
the Link LED and the right one is the Activity LED.
34
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION
Overview
The BitStorm 4800 Express is designed to require minimal configuration
before it can be accessed by a Network Operations Center (NOC). When the
BitStorm 4800 Express is first powered up it is a fully functional bridge, and
all DSL ports are set to their maximum speed.
Initial configuration is performed using the Command Line Interface (CLI).
The CLI is available from a terminal or PC connected to the CONSOLE port,
or through the management port (Port 1).
Additional configuration may be necessary, depending on the mode used to
manage the BitStorm 4800 Express:
z
Inband
z
Out of band through Port 1
This can be performed using the CLI, SNMP, or the web interface.
For more configuration information, see the BitStorm 4800 Express Model
4821-A2 Command Line Interface Reference (for the CLI) and the online
Help (for the web interface).
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
Using the CLI
A command line interface (CLI) can be used to configure and monitor the
unit. The CLI is available from a PC or terminal connected to the Console
port, or from a Telnet session with the device.
The following commands are available:
Table 4:
Command
clear
CLI Commands
Function
Clear the system log.
configure
copy
Enter Configuration mode.
Copy from one file to another.
Set the time zone and date format.
date
end
If user is in Administrator mode, shifts to User mode; if
user is in User mode, positions interface at top of menu
tree.
exit
Terminate current session.
firmware
paging
Download or apply new firmware.
Enable or disable paging (more prompt) for this
session.
privilege
restart
show
Enable administrator mode.
Restart a unit.
Display configuration, statistics, and status.
technical-support Display information for contacting technical support.
test Test the system.
Descriptions of some essential configuration commands follow.
36
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CLI
Configure Management Default Gateway Address
The configure management default gateway command specifies the IP
address of the next hop router for the management traffic.
configure management default-gateway {ip_address}
Minimum Access Level: Administrator
ip_address – Specifies the IP address of the default gateway for the
management ports.
Example:
PDYN# configure management default-gateway 137.90.127.1
Configure Management Inband Address
The configure management inband address command specifies the IP
address of the unit.
configure management inband address {ip_address} { subnet_mask}
Minimum Access Level: Administrator
ip_address – Specifies the management IP address. Default is 0.0.0.0
(disabled). Do not configure inband and out-of-band management on the
same subnet.
subnet_mask – Specifies the subnet mask to be applied to the IP address.
The default mask is 255.255.255.0.
Example:
PDYN# configure management inband address 137.90.127.3
255.255.255.0
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
Configure Management Out-of-Band Address
The configure management out-of-band address command specifies the IP
address of the unit that will accept management traffic on the out-of-band
management port.
configure management out-of-band address {bootp | {{ip_address} {
subnet_mask} }
Minimum Access Level: Administrator
bootp – Specifies that a BOOTP server will determine the management IP
address.
ip_address – Specifies the management IP address. The default address is
10.10.10.10. Do not configure inband and out-of-band management on the
same subnet.
subnet_mask – Specifies the subnet mask to be applied to the IP address.
The default mask is 255.255.255.0.
Example:
PDYN# configure management out-of-band address bootp
PDYN# configure management out-of-band address 137.90.127.3
255.255.255.0
38
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
BitStorm 4800 Express Startup Procedure
BitStorm 4800 Express Startup Procedure
You can initialize your BitStorm 4800 Express via a PC or terminal connected
to the unit’s CONSOLE port. Then, using a series of CLI commands,
GrandVIEW EMS or another Element Management System, or the web
interface, you can configure the unit according to your requirements.
Login
To log in to the BitStorm 4800 Express:
2 At the login> prompt, type admin and press Enter.
3 At the password> prompt, press Enter. The default login password is
blank.
4 At the PDYN> prompt, type privilege and press Enter.
5 At the password# prompt, press Enter. The default privileged password is
blank.
You are now logged on and in privileged mode, which allows you to configure
the unit.
Management Modes
The startup procedure for the BitStorm 4800 Express system differs
depending on the type of management used:
z
Inband Management – Operates over the uplink.
Out-of-Band Management – Operates over Port 1.
z
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
Startup Procedure for Inband Management
With inband management, the BitStorm 4800 Express is managed using the
uplink port.
To start up the BitStorm 4800 Express using inband management:
1 To avoid losing your connection when the IP address is changed, access
the CLI using the CONSOLE port.
2 Assign an IP address, netmask, and next-hop router using the configure
management command. For example:
PDYN# configure management inband address 137.90.127.3
255.255.255.0
PDYN# configure management default-gateway 137.90.127.1
Do not configure inband and out-of-band management on the same
subnet.
Startup Procedure for Out-of-Band Management
In out-of-band management, you manage the unit through Port 1.
To start up the BitStorm 4800 Express using out-of-band management:
1 To avoid losing your connection when the IP address is changed, access
the CLI using the CONSOLE port.
2 Assign an IP address, netmask, and next-hop router using the configure
management command. For example:
PDYN# configure management out-of-band address 137.90.80.3
255.255.255.0
PDYN# configure management default-gateway 137.90.80.1
You can now access the web interface by typing into the Location field of
your web browser the IP address assigned to the Port 1. See Using the
Do not configure inband and out-of-band management on the same
subnet.
3 Configure routers as necessary to route data from the NOC to the
BitStorm 4800 Express.
40
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Web Interface
Using the Web Interface
To access the web interface:
1 Open your web browser. (Internet Explorer Version 6 or above is
recommended.)
Address field of your browser window. For example:
3 A login window appears. Enter the default User ID (admin) and leave
Password blank. Click on OK. The web interface screen appears.
4 Click on the menu tab appropriate to what you would like to do:
— Configuration – To configure the system and interfaces
— Status – To display statistics, status, and contents of memory
— System – To display system information, download firmware, back
up configurations, and modify users
— Diagnostics – To start and stop tests
System / Users
For security reasons, it is a good idea to change the default password the first
time you use the system.
To change the default password for user admin:
1 Click on the System menu tab, then click on Users. The folllowing screen
appears.
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
2 In the Configured Users box, select admin by clicking in the circle next
to it.
3 Click on Modify Selected. The System / Users / admin screen appears.
4 Type in a new Login Password and a new Privilege Password, then click
on Apply. Keep a record of the new password.
Configuration / Management / SNMP
SNMP access to the unit is disabled by default. The read-only community
string is public, and the read-write string is private. Community strings,
network management system addresses, and trap manager addresses can be
set using the System/Management/SNMP screen.
To set SNMP parameters:
1 Click on the Configuration menu tab, then click on SNMP. The
System/Management/SNMP screen appears.
2
Enter new SNMP parameters as desired. Click on Apply.
42
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTORS AND PIN ASSIGNMENTS
Overview
The following sections provide pin assignments for:
z
z
z
PORT1
10/100BT
PORT2
10/100BT
CONSOLE
1
2
3
4
5
6
7
8
9
11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47
DSL PORTS 1-24
DSL PORTS 25-48
10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48
04-17535
Figure 2: BitStorm 4800 Express IP Front Panel
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Connectors and Pin Assignments
DSL Ports Connectors
The 50-pin RJ21X Telco connectors labeled DSL Ports 1–24 and (on the
48-port model) DSL Ports 25–48 provide the 2-wire loop interface from each
DSL port to the POTS splitter. The Canadian designation for this connector is
CA21A.
Table 5 lists the pin assignments for these interfaces. Note that Pins 25 and 50
are not used.
Table 5: DSL Connector Pinouts
1
Connector Pins
(Ring, Tip)
25
DSL Port
1 or 25
1, 26
2 or 26
2, 27
26
3 or 27
3, 28
50
02-17151
4 or 28
4, 29
5 or 29
5, 30
6 or 30
6, 31
7 or 31
7, 32
8 or 32
8, 33
9 or 33
9, 34
10 or 34
11 or 35
12 or 36
13 or 37
14 or 38
15 or 39
16 or 40
17 or 41
18 or 42
19 or 43
20 or 44
21 or 45
22 or 46
23 or 47
24 or 48
10, 35
11, 36
12, 37
13, 38
14, 39
15, 40
16, 41
17, 42
18, 43
19, 44
20, 45
21, 46
22, 47
23, 48
24, 49
44
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Port 1 and Port 2 10/100BaseT Connectors
Port 1 and Port 2 10/100BaseT Connectors
Port 1 and Port 2 are 8-pin unkeyed modular jacks for a 10/100BaseT
interface.
Table 6: Port 1 and Port 2 Pinouts
Signal
Pin
1
Pin 8
Pin 1
Transmitted Data +
Transmitted Data –
Received Data +
Unused
97-15449
2
3
4
Unused
5
Received Data –
Unused
6
7
Unused
8
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Connectors and Pin Assignments
Console Port Connector
The CONSOLE port connector is a DB9 socket connector that supports an
EIA-232-E circuit as shown in Table 7.
Table 7: Console Port Connector
Directio
RS-232 Signal
n
Pin
1
Ground
Out
Out
In
Receive Data
Send Data
2
3
Data Terminal Ready In
4
Ground
Ground
NC
—
5
Out
—
6
7
Ground
NC
Out
—
8
9
46
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUIPMENT LIST
Table 8: BitStorm 4800 Express Equipment List
Description
Model Number
BitStorm 4800 Express Model 4821-A2 Command Line 4821-A2-GB21
Interface Reference (paper copy)
BitStorm 4800 Express Model 4821-A2 SNMP Reference 4821-A2-GB22
(paper copy)
BitStorm 4800 Express 24-Port IP DSLAM, with North 4821-A2-427
America power cord
Includes BitStorm 4800 Express, 19- and 23-inch
mounting brackets and hardware, and Installation
Guide.
BitStorm 4800 Express 48-Port IP DSLAM, with North 4821-A2-447
America power cord
Includes BitStorm 4800 Express, 19- and 23-inch
mounting brackets and hardware, and Installation
Guide.
Mounting Brackets for ETSI 21-inch (535 mm) Rack
1-Slot POTS Splitter Chassis
4200-F1-001
5011-A1-000
5016-A1-000
6051-B1-001
6-Slot POTS Splitter Chassis
BitStorm 6051 Universal Line Sharing POTS Splitter
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Equipment List
48
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
Technical specifications are subject to change without notice.
Table 9: BitStorm 4800 Express Technical Specifications (Sheet 1 of 2)
Specifications
Criteria
Cooling and Air
Handling
Each BitStorm 4800 Express is independently cooled
with integral fans and does not rely on vertical air
flow.
DSL Compatibility
z
z
z
G.dmt (G.992.1)
G.lite (G.992.2)
ANSI T1.413-1998
Electromagnetic
Compatibility
(EMC)
Meets the following standards:
z
z
z
z
z
EN 300 386-2
EN 55024
EN 55022, Class A
FCC Part 15, Class A
VCCI, Class A
Interfaces
z
z
z
DSL PORTS: 50-pin RJ21X Telco-type connector
CONSOLE: DB9 (EIA-232-E)
Port 1 and Port 2: 8-pin modular jack
(10/100BaseT)
Operating
Environment
Ambient Temperature: 0° to 50° C (32° to 122° F)
Relative Humidity: 5% to 95% noncondensing
Storage Temperature: –40° to 85° C (–40° to 185° F)
Shock and vibration tolerance sufficient to withstand
normal shipping
Physical
Dimensions
Height: 1.75″ (44.5 mm, or 1U as defined in
EIA-310-C) without feet
Width: 17.2″ (437 mm) without mounting brackets
Depth: 16.0″ (406 mm) with cables
Power
90–265 VAC, 47–63 Hz
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Table 9: BitStorm 4800 Express Technical Specifications (Sheet 2 of 2)
Specifications
Criteria
Power
Consumption
Model 4821-A2-417: 12 Watts Maximum
Model 4821-A2-427: 26 Watts Maximum
Model 4821-A2-447: 40 Watts Maximum
Weight
Model 4821-A2-417: 11.2 lbs (5.1 kg)
Model 4821-A2-427: 11.2 lbs (5.1 kg)
Model 4821-A2-447: 10.7 lbs (4.8 kg)
50
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
equipment list
Ethernet
M
Management port
F
modem
G
N
I
inband management
O
installing
out-of-band management
overview
P
J
L
52
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Port 1
Port 2
T
Telco connectors
POTS splitter
U
uplink
V
R
W
wall mount
web interface
S
specifications
4821-A2-ZN21-30
BitStorm 4800 Express Model 4821-A2 Installation Guide
53
Download from Www.Somanuals.com. All Manuals Search And Download.
54
BitStorm 4800 Express Model 4821-A2 Installation Guide
4821-A2-ZN21-30
Download from Www.Somanuals.com. All Manuals Search And Download.
|