EN
User manual
Washing Machine
ZWI 71201 WA
ZWI 71401 WA
Download from Www.Somanuals.com. All Manuals Search And Download.
not pressing the electrical supply cable against the
wall.
aged so that the inside of the washing machine is ac-
cessible.
• If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely
under the appliance.
• Always be sure, that there is no water leakage from ho-
ses and their connections after the installation.
Child safety
• This appliance is not intended for use by person (in-
cluding children) with reduced physical sensory or
mental capabilities or lack of experience and knowl-
edge unless they have been given supervision or in-
struction concerning use of the appliance by a person
responsible for their safety.
• If the appliance is installed in a location subject to
frost, please read the “dangers of freezing” chapter.
• Any plumbing work required to install this appliance
should be carried out by a qualified plumber or compe-
tent person.
• Any electrical work required to install this appliance
should be carried out by a qualified electrician or com-
petent person.
• Children should be supervised to ensure that they do
not play with the appliance.
• The packaging components (e.g. plastic film, polystyr-
ene) can be dangerous to children - danger of suffoca-
tion! Keep them out of children’s reach
• Keep all detergents in a safe place out of children’s
reach.
Use
• Make sure that children or pets do not climb into the
drum. To prevent children and pets becoming trapped
inside the drum this machine incorporates a special
feature.
• This appliance is designed for domestic use. It must
not be used for purposes other than those for which it
was designed.
• Only wash fabrics which are designed to be machine
washed. Follow the instructions on each garment label.
• Do not overload the appliance. See the Washing Pro-
gramme Table.
• Before washing, ensure that all pockets are empty and
buttons and zips are fastened. Avoid washing frayed or
torn articles and treat stains such as paint, ink, rust,
and grass before washing. Underwired bras must NOT
be machine washed.
To activate this device, ro- To disable this device and
• Garments which have been in contact with volatile pe-
troleum products should not be machine washed. If
volatile cleaning fluids are used, care should be taken
to ensure that the fluid is removed from the garment
before placing in the machine.
• Never pull the power supply cable to remove the plug
from the socket; always take hold of the plug itself.
tate the button (without
pressing it) inside the
door clockwise until the
groove is horizontal. If
necessary use a coin.
restore the possibility of
closing the door, rotate the
button anti-clockwise until
the groove is vertical.
• Never use the appliance if the power supply cable, the
control panel, the working surface or the base are dam-
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product description
Detergent dispenser drawer
1
1
2
Control panel
Door opening handle
Rating plate
2
3
4
5
6
Drain pump
Adjustable feet
3
4
5
6
Detergent dispenser drawer
Compartment for detergent used for prewash and soak
phase or for stain remover used during the stain action
phase (if available). The prewash and soak detergent is
added at the beginning of the wash programme. The stain
remover is added during the stain action phase.
Compartment for powder or liquid detergent used for
main wash. If using liquid detergent pour it just before
starting the programme.
Compartment for liquid additives (fabric softener,
starch).
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in the
detergent dispenser drawer. Any fabric softener or starch-
ing additives must be poured into the compartment before
starting the wash programme.
Control panel
On the following page there is a picture of the control panel. It shows the programme selector dial as well as the
buttons, pilot lights and the display. These are presented by relevant numbers on the following pages.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
10
9
Programme selector dial
SPIN reduction button
OPTIONS button
EXTRA RINSE button
START/PAUSE button
DELAY START button
1
2
3
4
5
6
7
8
PREWASH button
DOOR LOCKED pilot light
Display
9
EASY IRON button
10
Programme selector dial, spin speed button and available options
Programme Selector Dial
Prewash
It allows you to switch the appliance on/off and/or to se-
lect a programme.
By selecting this option the machine performs a prewash
cycle before the main wash phase. The washing time will
be prolonged. This option is recommended for heavily
soiled laundry.
Spin Reduction
By pressing this button you can change the spin speed of
the selected programme.
Easy Iron
By selecting this option the laundry is gently washed and
spun to avoid any creasing. In this way ironing is easier.
Furthermore the machine will perform some additional
rinses in some programmes. On cotton programmes the
maximum spin speed is reduced automatically.
Rinse hold
By selecting this function the water of the last rinse is not
emptied out to prevent the fabrics from creasing. Before
opening the door it will be necessary to empty out the wa-
ter. To empty out the water, please read the paragraph «At
the end of the programme».
Extra Rinse
This appliance is designed to save energy. If it necessary
to rinse the laundry using an extra quantity of water (extra
rinse), select this option. Some additional rinses will be
performed. This option is recommended for people who
are allergic to detergents, and in areas where the water is
very soft.
Economy
Only for cottons and synthetic items lightly or normally
soiled at a temperature of 40°C or higher. The washing
time will be prolonged and the washing temperature will
be reduced. You can use this option if you want to wash
normally soiled laundry and at the same time save energy.
Start Pause
Quick Wash
This button allows you to start or to interrupt the selected
programme.
A very short cycle for lightly soiled items or for laundry
which needs only freshening up. We recommend you to
reduce the fabrics loading.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
10.2:
Delay Start
• Duration of the selected programme
After selecting a programme, the duration is displayed
in hours and minutes (for example
The programme can be delayed from 30 min - 60 min - 90
min, 2 hours and then by 1 hour up to a maximum of 20
hours by means of this button.
). The dura-
tion is calculated automatically on the basis of the
maximum recommended load for each type of fabric.
After the programme has started, the time remaining is
updated every minute.
Door locked pilot light
The pilot light 9 illuminates when the programme starts
and indicates if the door can be opened:
• light on: the door cannot be opened. The machine is
working or has stopped with water left in the tub.
• light off: the door can be opened. The programme is
finished or the water has been emptied out.
• Delayed start
The Selected delay set by pressing the relevant button
appears on the display for a few seconds, then the du-
ration of the selected programme is displayed again.
The delay time value decreases by one unit every hour
and then, when 1 hour remains, every minute.
• light blinking: the door is opening in a few minutes.
Display (10)
• Alarm codes
In the event of operating problems, some alarm codes
10.1
10.2
can be displayed, for example
«What to do if...»).
(see paragraph
• Incorrect option selection
If an option which is not compatible with the set wash
programme is selected, the message Err is displayed at
the bottom of the display for a few seconds. The inte-
grated red light of button 7 starts flashing.
The display shows the following information:
10.1: Child safety lock
This device permits you to leave the appliance unattended
during it's functioning.
• End of programme
When the programme has finished the flashing zero (
) is displayed. The pilot light 9 and the pilot light of
button 7 go out. The door can be opened.
Washing programmes
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Options
Compartment
4)
1–2–3–4
SPIN REDUCTION
90° - 30°
Main wash - Rinses
Maximum spin speed at 1200 rpm for model ZWI71201WA
Maximum spin speed at 1400 rpm for model ZWI71401WA
Max. load 7 kg - Reduced load 3 kg
RINSE HOLD
ECO1)
QUICK WASH2)
PREWASH
EASY IRON 3)
EXTRA RINSE
White and coloured cotton (normally soiled items).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
4)
5–6–7
60° - 30°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 3 kg - Reduced load 1.5 kg
Synthetic or mixed fabrics: underwear, coloured garments,
non-shrink shirts, blouses.
SPIN REDUCTION
RINSE HOLD
ECO 1)
SUPER QUICK 2)
PREWASH
EASY IRON 3)
EXTRA RINSE
4)
8–9
40° - 30°
Main wash - Rinses
Maximum spin speed 700 rpm
Max. load kg 3 - Reduced load kg 1.5
Delicate fabrics: acrylics, viscose, polyester.
RINSE HOLD
PREWASH
SUPER QUICK 2)
EXTRA RINSE
10–11–12
40° - Cold
SPIN REDUCTION
RINSE HOLD
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
Special programme for delicate fabrics with «hand wash-
ing» care symbol.
13
40°
SPIN REDUCTION
RINSE HOLD
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
Washing programme for machine washable wool as well as
for hand washable woollens and delicate fabrics. Note: A
single or bulky item may cause imbalance. If the appliance
doesn’t perform the final spin phase, add more items, redis-
tribute the load manually and then select the spinning pro-
gramme.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
4)
14–Jeans
40°
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 3 kg
SPIN REDUCTION
RINSE HOLD
PREWASH
EASY IRON 3)
With this programme it is possible to wash items like trou-
sers, shirts or jackets in denim and also jersey realized with
hi-tech materials. (The Extra Rinse option will be activated
automatically).
15–Curtains
40°
RINSE HOLD
EXTRA RINSE
Prewash - Main wash - Rinses
Maximum spin speed at 700 rpm
Max. load 2.5 kg
This programme it is possible to wash with an extra water
load. The machine will add automatically a prewash phase
before the main wash to eliminate the dust. (Do not put any
detergent in the prewash compartment).
16–Soak
30°
Prewash - Soak for about 40 minutes - Stop with water in
the tub
Max. load 7 kg
Special programme for heavily soiled laundry. The machine
performs a soak at 30° C. At the end of this time the ma-
chine will stop automatically with water left in the tub.
Before starting a new washing phase, it is necessary to
empty out the water by:
• Draining only: turn the programme selector dial to Drain
programme. (Press the button 7).
• Draining and spinning: turn the programme selector dial
to programme Spin, reduce the spin speed by pressing
the button 2, and then press button 7.
Important! This programme cannot be used for very delicate
fabrics as silk or wool. Pour the detergent for the soak pro-
gramme into the appropriate compartment. At the end of the
soak (after having emptied out the water) you can select the
washing programme (first turn the programme selector dial
to
, then to the programme and press the button 5).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
17–Mini 30’
Main wash - Rinses
Maximum spin speed at 700 rpm
Max. load 3 kg
Quick washing programme for cotton and synthetic items
which are lightly soiled or only need freshening up.
18–Rinse
Rinses
SPIN REDUCTION
RINSE HOLD
EASY IRON 3)
EXTRA RINSE
Maximum spin speed at 1200 rpm for model ZWI71201WA
(1400 rpm for model ZWI71401WA)
Maximum spin speed at 1400 rpm for model ZWI71401WA
Max. load 7 kg
With this programme it is possible to rinse and spin cotton
garments which have been washed by hand. The machine
performs 3 rinses, followed by a final long spin. The spin
speed can be reduced.
19–Drain
Draining of water
Max. load 7 kg
For emptying out the water of the last rinse in programmes
with stops with water in the drum.
20–Spin
SPIN REDUCTION
Drain and long spin
Maximum spin speed at 1200 rpm for model ZWI71201WA
(1400 rpm for model ZWI71401WA)
Maximum spin speed at 1400 rpm for model ZWI71401WA
Max. load 7 kg
Separate spin for hand washed cotton garments and after
programmes with the Rinse Hold or Night Cycle option se-
lected. You can choose the spin speed by pressing the rele-
vant button to adapt it to the fabrics to be spun.
For cancelling the programme which is running or to switch the machine off.
1) This option is not active at a temperature lower than 40° C.
2) If you select the Super Quick option by pressing button 3, we recommend that you reduce the maximum load as indicated. Full
loading is possible however with somewhat reduced cleaning results.
3) Max. load with Easy iron option 1.5 kg
4) If using liquid detergents, a programme without PREWASH must be selected.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Helpful hints and tips
Red wine: soak in water and detergent, rinse and treat with
acetic or citric acid, then rinse. Treat any residual marks
with bleach.
Sorting out the laundry
Follow the wash code symbols on each garment label and
the manufacturer’s washing instructions. Sort the laundry
as follows: whites, coloureds, synthetics, delicates, wool-
lens.
Ink: depending on the type of ink, moisten the fabric first
with acetone1), then with acetic acid; treat any residual
marks on white fabrics with bleach and then rinse thor-
oughly.
Before loading the laundry
Never wash whites and coloureds together. Whites may
lose their whiteness in the wash.
New coloured items may run in the first wash; they should
therefore be washed separately the first time.
Button up pillowcases, close zip fasteners, hooks and
poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special detergent or
detergent paste.
Tar stains: first treat with stain remover, methylated spirits
or benzine, then rub with detergent paste.
Detergents and additives
Good washing results also depend on the choice of deter-
gent and use of the correct quantities to avoid waste and
protect the environment.
Although biodegradable, detergents contain substances
which, in large quantities, can upset the delicate balance
of nature.
The choice of detergent will depend on the type of fabric
(delicates, woollens, cottons, etc.), the colour, washing
temperature and degree of soiling.
All commonly available washing machine detergents may
be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics (60°C max) and
woollens
• liquid detergents, preferably for low temperature wash
programmes (60°C max) for all types of fabric, or spe-
cial for woollens only.
The detergent and any additives must be placed in the ap-
propriate compartments of the dispenser drawer before
starting the wash programme.
Treat curtains with special care. Remove hooks or tie them
up in a bag or net.
Removing stains
Stubborn stains may not be removed by just water and de-
tergent. It is therefore advisable to treat them prior to
washing.
Blood: treat fresh stains with cold water. For dried stains,
soak overnight in water with a special detergent then rub
in the soap and water.
Oil based paint: moisten with benzine stain remover, lay
the garment on a soft cloth and dab the stain; treat several
times.
Dried grease stains: moisten with turpentine, lay the gar-
ment on a soft surface and dab the stain with the fingertips
and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust removing
product used cold. Be careful with rust stains which are
not recent since the cellulose structure will already have
been damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well (whites and fast
coloureds only).
If using liquid detergents, a programme without prewash
must be selected.
Your appliance incorporates a recirculation system which
allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in
the detergent dispenser drawer.
Grass: soap lightly and treat with bleach (whites and fast
coloureds only).
Quantity of detergent to be used
Ball point pen and glue: moisten with acetone1), lay the
garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone as above, then treat stains
with methylated spirits. Treat any residual marks with
bleach.
The type and quantity of detergent will depend on the type
of fabric, load size, degree of soiling and hardness of the
water used.
Follow the product manufacturers’ instructions on quanti-
ties to use.
Use less detergent if:
1) do not use acetone on artificial silk
10
Download from Www.Somanuals.com. All Manuals Search And Download.
• you are washing a small load
• the laundry is lightly soiled
• large amounts of foam form during washing.
area can be obtained from the relevant water supply com-
pany, or from your local authority. If the water hardness
degree is medium or high we suggest you to add a water
softener following always the manufacturer’s instructions.
When the degree of hardness is soft, readjust the quantity
of the detergent.
Degrees of water hardness
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in your
First use
• Ensure that the electrical and water connections
comply with the installation instructions.
• Remove the polystyrene block and any material
from the drum.
activate the ECO valve. Then run a cotton cycle at
the highest temperature without any laundry in
the machine, to remove any manufacturing resi-
due from the drum and tub. Pour 1/2 a measure
of detergent into the main wash compartment and
start the machine.
• Pour 2 litres of water into the main wash com-
partment
of the detergent drawer in order to
Personalisation
by or cause damage to the appliance. This function re-
mains enabled also when the washing machine is not
working.
There are two different ways to set this option:
1. Before pressing button 7: it will be impossible to
start the machine.
2. After pressing button 7: it will be impossible to
change any other programme or option.
To enable or disable this option press simultaneously for
about 6 seconds buttons 2 and 3 until on the display, the
Acoustic signals
The machine is provided with an acoustic device, which
sounds in the following cases:
• at the end of the cycle
• if there is a fault.
By pressing the 4 and 5 buttons simultaneously for about
6 seconds, the acoustic signal is deactivated (except if
there is a fault). By pressing these 2 buttons again, the
acoustic signal is reactivated.
Child safety lock
This device permits you to leave the appliance unattended
so you do not need to worry that children might be injured
icon
appears or disappears.
Daily use
Load the laundry
Make sure that no laundry
stays between the seal and
the door. There is a risk of
water leakage or damage
to the laundry.
Open the door by carefully
pulling the door handle
outwards. Place the laun-
dry in the drum, one item
at a time, shaking them
out as much as possible.
Close the door.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Measure out the detergent and the fabric softener
Select the available options by means of buttons 3,
4, 5 and 6
Depending on the programme, different options can be
combined. These must be selected after choosing the de-
sired programme and before starting the programme.
When these buttons are pressed, the corresponding pilot
lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected, the inte-
grated red pilot light of the button 7 flashes 3 times and
the message Err is displayed.
For the compatibility among the washing programmes and
the options see chapter «Washing programmes».
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent required, pour it into the
main wash compartment
or in the appropriate com-
Start the programme by pressing button 7
partment if the selected programme/option it requires
(see more details in "Detergent dispenser drawer").
If required, pour fabric softener into the compartment
To start the selected programme, press this button; the
corresponding green pilot light stops blinking.
The pilot light 9 illuminates to indicate that the appliance
starts operating and the door is locked.
If you have chosen a delayed start, the machine will begin
the countdown.
marked
(the amount used must not exceed the
«MAX» mark in the drawer). Close the drawer gently.
Select the required programme by means of the
programme selector dial (1)
Turn the programme selector dial to the required pro-
gramme.
Important! If an incorrect option is selected, the message
Err is displayed for a few seconds and the red pilot light of
this button blinks 3 times.
The green pilot light of button 7 starts to flash. The selec-
tor dial can be turned either clockwise or anticlockwise.
Select the Delay Start by pressing button 8
Before you start the programme, if you wish to delay the
start, press this button to select the desired delay.
The selected delay time value will appear on the display
for a few seconds, then the duration of the programme will
appear again.
Turn the selector dial to position
to reset the pro-
gramme/to switch the machine OFF.
At the end of the programme the selector dial must be
turned to position , to switch the machine off.
You must select this option after you have set the pro-
gramme and before you start the programme.
You can cancel or modify the delay time at any moment,
before you press button 7.
Selecting the delay start :
1. Select the programme and the required options.
2. Select the delay start by pressing button 8.
Important! If you turn the programme selector dial to
another programme when the machine is working, the red
pilot light of button 7 will blink 3 times and the
messageErr is displayed to indicate a wrong selection.
The machine will not perform the new selected
programme.
Select the spin speed by pressing button 2
3. Press button 7:
When selecting a programme, the appliance proposes au-
tomatically the maximum spin speed provided for that
programme. (See "Washing programmes" for the maxi-
mum allowed spin speed).
Press this button repeatedly to change the spin speed, if
you want your laundry to be spun at a different speed. The
relevant pilot light illuminates.
- the machine starts its hourly countdown.
- the programme will start after the selected delay
has expired.
Cancelling the Delay Start after having started the pro-
gramme:
1. Set the washing machine to PAUSE by pressing but-
ton 7.
2.
Press button 8 once. On the display will appear '.
3. Press button 7 again to start the programme.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
If the pilot light 9 remains lit, this means that the machine
is already heating or that the water level is too high. In any
case, do not try to force the door open!
If you cannot open the door but you need to open it, you
have to switch the machine off by turning the selector dial
Important!
• The selected delay can be changed only after selecting
the washing programme again.
• The door will be locked throughout the delay time. If
you need to open the door, you must first set the wash-
ing machine to PAUSE by pressing button 7 and wait a
few minutes before opening the door. After you have
closed the door, press the same button again.
to
. After a few minutes the door can be opened.
(Pay attention to the water level and temperature!).
After closing the door, it is necessary to select the pro-
gramme and options again and to press button 7.
Important! The Delay Start cannot be selected with the
draining programme.
At the end of the programme
The machine stops automatically. Some acoustic signals
sound and a blinking appears on the display. The pilot
light of button 7 and the pilot light 9 go off.
If you have set a programme or an option that ends with
water left in the tub, the pilot light 9 remains on. The door
is locked to indicate that the water must be emptied out.
During this time the drum continues to turn at regular in-
tervals until water draining.
Altering an option or a running programme
It is possible to change some options before the pro-
gramme carries them out.
Before you make any change, you must pause the washing
machine by pressing button 7.
Changing a running programme is possible only by reset-
ting it. Turn the programme selector dial to
and then
to the new programme position. Start the new programme
by pressing button 7 again.
The washing water in the tub will be not emptied out.
Follow the below instructions to empty out the water:
1.
Turn the programme selector dial to
.
2. Select the draining or spinning programme.
3. Reduce the spin speed if needed, by pressing the
relevant button.
4. Press button 7.
At the end of the programme, the door is released and can
Interrupting a programme
Press the button 7 to interrupt a programme which is run-
ning, the corresponding pilot light starts blinking. Press
the button again to restart the programme.
be opened. Turn the programme selector dial to
switch the machine off.
Remove the laundry from the drum and carefully check
that the drum is empty. If you do not intend to carry out
another wash, close the water tap. Leave the door open to
prevent the formation of mildew and unpleasant smells.
to
Cancelling a programme
Turn the selector dial to
is running. Now you can select a new programme.
to cancel a programme which
Opening the door after the programme has started
First set the machine to pause by pressing the button 7.
If the pilot light 9 blinks and after a few minutes goes off,
the door can be opened.
Stand by : once the programme has finished after a few
minutes the energy saving system will be enabled. The
brightness of the display is reduced. By pressing any but-
ton the appliance will come out of the energy saving sta-
tus.
Care and cleaning
chine. Do this separately from any laundry washing, and
according to the softening powder manufacturer's instruc-
tions. This will help to prevent the formation of lime de-
posits.
Warning! You must DISCONNECT the appliance
from the electricity supply, before you can carry out
any cleaning or maintenance work.
Descaling
The water we use normally contains lime. It is a good idea
to periodically use a water softening powder in the ma-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
External cleaning
Clean the exterior cabinet of the appliance with soap and
water only, and then dry thoroughly.
Warning! Before opening the pump door, switch the
appliance off and remove the mains plug from the
socket.
Proceed as follows:
Cleaning the dispenser drawer
• Unplug the appliance.
• If it is necessary, wait until the water has cooled down.
The washing powder and additive dispenser drawer
should be cleaned regularly.
Place a container close to
the pump (A) to collect
any spillage.
Pull out the emergency
emptying hose (B), place it
in the container and re-
move its cap.
Remove the drawer by
To aid cleaning, the top
pressing the catch down- part of the additive com-
wards and by pulling it
out. Flush it out under a
tap, to remove any traces
of accumulated powder.
partment should be re-
moved.
Cleaning the drawer recess
When no more water comes out, unscrew the pump
cover by turning it anti-clockwise and remove the filter.
Use pliers, if necessary. Always keep a rag nearby to
dry up any water spillage when removing the cover.
Clean the filter under a tap, to remove any traces of fluff.
Having removed the draw-
er, use a small brush to
clean the recess, ensuring
that all washing powder
residue is removed from
the upper and lower part of
the recess.
Remove foreign bodies
and fluff from the filter seat
and from the pump impel-
ler.
Check carefully whether
the pump impeller rotates
(it rotates jerkily). If it
doesn’t rotate, please con-
tact your Service Centre.
Replace the drawer and run the rinse programme with-
out any clothes in the drum.
Cleaning the pump
The pump should be inspected regularly and particularly
if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump;
• a problem with water draining is detected (see chapter
“What to do if...” for more details).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Put the cap back on the
emergency emptying hose
and place the latter back in
its seat.
• Unscrew the hose from the machine. Keep a rag
nearby because some water may flow.
• Clean the filter in the valve with a stiff brush or with
the piece of cloth.
Replace the filter into the
pump by inserting it cor-
rectly into the special
guides. Screw the pump
cover firmly by turning it
clockwise.
35°
45°
Caution! When the appliance is in use and
depending on the programme selected there can be
hot water in the pump.
Never remove the pump cover during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When refitting the pump cover, ensure it is
securely re-tightened so as to stop leaks and young
children being able to remove it.
• Screw the hose back to the machine and make sure
the connection is tight.
• Turn on the water tap.
Frost precaution
If the machine is exposed to temperatures below 0°C, cer-
tain precautions should be taken.
Cleaning the water inlet filters
• Turn off the water tap.
• Unscrew the inlet hose.
• Place the end of the emergency emptying hose and that
of the inlet hose in a bowl placed on the floor and let
water drain out.
Important! If the appliance doesn't fill, takes long to fill
with water, the starting button blinks yellow or the display
(if available) shows the relevant alarm (see chapter "What
to do if..." for more details), check if the water inlet filters
are blocked .
• Screw the water inlet hose back on and reposition the
emergency emptying hose after having put the cap on
again.
• When you intend to start the machine up again, make
sure that the room temperature is above 0°C.
To clean the water inlet filters:
• Turn off the water tap.
• Unscrew the hose from
the tap.
Emergency emptying out
If the water is not discharged, proceed as follows to empty
out the machine:
• Clean the filter in the
hose with a stiff brush.
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• Screw the hose back onto the tap. Make sure the
connection is tight.
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until water stops
flowing out;
• clean the pump if necessary as previously described;
15
Download from Www.Somanuals.com. All Manuals Search And Download.
• replace the emergency emptying hose in its seat after
having plugged it;
• screw the pump cover again and close the door.
into the main wash compartment of the detergent drawer
and then run the drain programme. This will activate the
ECO Valve device avoiding that part of the detergent
remains unused at next washing.
Important! Every time you drain the water through the
emergency emptying hose you must pour 2 litres of water
What to do if ...
Certain problems are due to lack of simple maintenance or
oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that the red pilot
light of button 7 blinks, one of the following alarm codes
appears on the display and some acoustic signals sound
every 20 seconds to indicate that the machine is not work-
ing:
•
•
•
: problem with the water supply.
: problem with the water draining.
: door open.
Once the problem has been eliminated, press the button 7
to restart the programme. If after all checks, the problem
persists, contact your local Service Centre.
Problem
Possible cause/Solution
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
The machine does not start:
• Replace the fuse.
The selector dial is not correctly positioned and the button 7 has not been
pressed.
• Please turn the selector dial and press the button 7 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The Child Safety Lock has been activated.
• Deactivate the Child Safety Lock.
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked.
The machine does not fill:
• Clean the water inlet filters. (See "Cleaning the water inlet filters" for more
details).
The door is not properly closed.
• Close the door firmly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause/Solution
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged.
• Clean the drain filter.
An option or a programme that ends with the water still in the tub or a that
eliminates all the spinning phases has been selected.
The machine does not empty and/or
does not spin:
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Too much detergent or unsuitable detergent (creates too much foam) has been
used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if it is
damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
There is water on the floor:
• Replace it with a new one.
The cap on the emergency emptying hose has not been replaced or the filter
has not been properly screwed in after cleaning action.
• Refit the cap on the emergency emptying hose or screw the filter fully in.
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
Unsatisfactory washing results:
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the pilot light 9 goes off.
There is water in the drum.
The door will not open:
• Select drain or spin programme to empty out the water.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause/Solution
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
The machine vibrates is noisy:
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
The electronic unbalance detection device has cut in because the laundry is
not evenly distributed in the drum. The laundry is redistributed by reverse rota-
tion of the drum. This may happen several times before the unbalance disap-
pears and normal spinning can resume. If, after 10 minutes, the laundry is still
not evenly distributed in the drum, the machine will not spin. In this case, re-
distribute the load manually and select the spin programme.
Spinning starts late or the machine
does not spin:
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select the spinning
programme.
The machine is fitted with a type of motor which makes an unusual noise com-
pared with other traditional motors. This new motor ensures a softer start and
more even distribution of the laundry in the drum when spinning, as well as
increased stability of the machine.
The machine makes an unusual
noise:
Machines based on modern technology operate very economically using very
little water without affecting performance.
No water is visible in the drum:
If you are unable to identify or solve the problem, contact
our service centre. Before telephoning, make a note of the
model, serial number and purchase date of your machine:
the Service Centre will require this information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Technical data
Dimensions
Width
Height
Depth
60 cm
85 cm
54 cm
Electrical connection
Information on the electrical connection is given on the rating plate, on the
inner edge of the appliance door.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Spin Speed
Cotton
7 kg
Maximum
1200 rpm (ZWI71201WA)
1400 rpm (ZWI71401WA)
Consumption values
Programme1)
Energy consumption (KWh)2)
Water consumption (litre)2)
White Cottons 90 °C
Cottons 60 °C
2.2
72
67
67
42
63
55
1.35
0.85
0.55
0.55
0.25
Cottons 40 °C
Synthetics 40 °C
Delicates 40 °C
Wool/ Handwash 30 °C
1) Refer to the display for the programme time.
2) The consumption information shown in this chart is indicative. It can vary depending on the quantity and the type of laundry, on the
temperature of the water supply and on the ambient temperature.
in terms of combined energy and water consumption for
washing that type of cotton laundry.
They agree with EN60456.
Standard programmes for the Energy Label consumption
values
The cotton 60 °C economy and cotton 40 °C economy are
the standard cotton programmes for normally soiled cot-
ton laundry. They are suitable to clean normally soiled
cotton laundry and they are the most efficient programmes
The actual water temperature may differ from the de-
clared cycle temperature.
Installation
Unpacking
All transit bolts and packing must be removed before us-
ing the appliance.
You are advised to keep all transit devices so that they can
be refitted if the machine ever has to be transported again.
After removing all the
packaging, carefully lay
Remove the power supply
cable and the hoses from
machine on it's back to re- the hose holders on the
move the polystyrene base rear of the appliance.
from the bottom.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Accurate levelling prevents vibration, noise and displace-
ment of the machine during operation.
Caution! Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor. After having levelled the
appliance, tighten the lock nuts.
Raising the appliance
Suspended wooden floors are particularly susceptible to
vibration.
Unscrew the three bolts
with the supplied spanner. tic spacers.
Slide out the relevant plas-
To help prevent vibration we recommend you place a wa-
terproof wood panel, at least 15 mm thick under the appli-
ance, secured to at least 2 floor beams with screws, the
wood panel must extend beyond the front feet.
If possible install the appliance in one of the corners of
the room, where the floor is more stable.
Water inlet
Warning! This appliance must be connected to a
cold water supply
Fill the smaller upper hole and the two large ones with
the corresponding plastic plug caps supplied in the bag
containing the instruction booklet.
Caution! Before connecting up the appliance to new
pipework or to pipework that has not been used for
some time, run off a reasonable amount of water to flush
out any debris that may have collected
Positioning
Install the machine on a flat hard floor. Make sure that air
circulation around the machine is not impeded by carpets,
rugs etc. Check that the machine does not touch the wall
or other kitchen units.
Caution! Do not use the hose from your previous
appliance to connect to water supply.
Connect the hose to a tap
with a 3/4” thread. Always
use the hose supplied with
the appliance.
Level the washing ma-
chine by raising or lower-
ing the feet. The feet may
be tight to adjust as they
incorporate a self locking
nut, but the machine
MUST be level and stable.
If necessary, check the
setting with a spirit level.
Any necessary adjustment
can be made with a span-
ner.
35°
45°
20
Download from Www.Somanuals.com. All Manuals Search And Download.
The other end of the inlet hose which connects to the
appliance can be turned as showed in the picture.
Do not place the inlet hose downwards. Angle the hose
to the left or right depending on the position of your
water tap. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks.
Place the drain hose into your standpipe, which should
have an internal diameter of approximately 38 mm thus
ensuring there is an air break between the drain hose
and standpipe.
When discharging into a standpipe ensure that the top
of the standpipe is no more than 90 cm (35.4'') and no
less than 60 cm (23.6'') above floor level.
38 mm (1.5”)
standpipe
diamater
Caution! The inlet hose must not be lengthened. If it
is too short and you do not wish to move the tap,
you will have to purchase a new, longer hose specially
designed for this type of use.
30 cm (12”)
Warning! Installation should comply with local
water authority and building regulations’
requirements.
The appliance must be connected to a cold water supply.
A minimum water pressure of 0.05 MPa (0.5 bar) is
required for safe operation of the appliance.
If you cannot make the cold water connection direct from
the rising mains, you may be able to operate the appliance
from your cold water storage system.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre. The
joining piece must have an internal diameter of 18 mm.
There should be a minimum vertical distance of 5.02 m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
Water drainage
This appliance is designed to be permanently plumbed in-
to your home's drainage system using one of the follow-
ing methods.
Min. 60 cm (23.6”)
Max. 90 cm (35.4”)
If your drain hose looks
like this (see beside) you
do not require the “U”
piece”. Just push the hose
firmly in to the standpipe.
1. Into a drainage standpipe.
Firstly form a hook in the end of the drain hose using
the “U” piece” supplied.
2. Onto a sink outlet spigot.
“U” piece supplied
Loop
21
Download from Www.Somanuals.com. All Manuals Search And Download.
If you require any further advice please contact your local
water authority.
If the outlet spigot has not Push the drain hose onto
been used before, remove the spigot and secure with
any blanking plug that
may be in place.
a clip, ensure a loop is
formed in the drain hose
(see above) to prevent
waste from the sink enter-
ing the appliance.
SHOWER
TOILET
SINK
BATH
BIDET
If you intend to drain the hose from the machine into a
sink, make sure that the sink is empty and the plug hole
is not blocked. Use the plastic “U - Piece” supplied.
WASHING
MACHINE
DISHWASHER
RAINWATER
‘RUN-OFF’
In the interest of the environment
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
The appliance should be connected to the FOUL drainage
system, the water will then be taken to a sewage works for
treatment before being discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is dis-
charged directly into a river or stream and may cause pol-
lution.
FOUL SEWERS
SEWAGE TREATMENT
WORKS
TREATED DISCHARGE
RIVER
UNTREATED
DISCHARGE
RIVER
In the event of having to change the fuse in the plug sup-
plied, a 13 amp ASTA approved (BS1363/A) fuse must be
used.
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or compe-
tent person.
Warning! A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of safely. Should
the appliance power supply cable need to be replaced, this
MUST be carried out by our Service Force Centre. The
appliance should not be connected to the electrical supply
by means of an extension cable.
Warning! THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should this
safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate.
Note!
Warning! Information on the electrical connection is
given on the rating plate on the inner edge of the
appliance door.
When the appliance is installed the power supply cable
must be accessible.
The appliance is supplied with a 13 amp plug fitted.
Building in
This appliance has been designed to be built into the
kitchen furniture. The recess should have the dimensions
shown in picture A.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
35 Ø 12,5-14 depth
16-22
B
600
min.
596
555
560
C
min.
820
416
176,5
416
818
75
60
22 1,5
170
100
595-598
A
C
When installing the appliance into the kitchen furniture
ensure, if possible, the hoses are placed in either of the
two recesses on the back of the appliance.
This will help to prevent the hoses from becoming
kinked or trapped.
• a) Door
The dimensions of the door should be:
- width 595-598 mm
- thickness 16-22 mm
The height (C-Fig. C) depends on the height of the ad-
jacent furniture's base.
• b) Hinges
To mount the hinges it is necessary to drill two holes
(dia. 35 mm, depth 12.5-14 mm depending on the
depth of door furniture) on the inner side of the door.
The distance between the holes hobs fixing centres
must be 416 mm.
6
The distance (B) from upper edge of the door to the
centre of the hole depends on the adjacent furniture's
dimensions.
The required dimensions are given in the picture C.
The hinges will be fixed to the door by means of screws
for wood (2-Fig. B) supplied with the appliance.
1
5 4
7
3
• c) Mounting the door
2
Fix the hinges (1) to the machine by means of the M
5x15 screws (3-Fig. B). The hinges can be adjusted to
compensate for possible uneven thickness of the door.
To align the door perfectly it is necessary to loosen the
screw (3-Fig. B), adjust the door and tighten the screw
again.
8
B
Caution! Do not remove the screw 8!
Preparation and assembly of the door
The machine is originally prearranged for the assembly
of a door opening from right to left.
In this case it is sufficient to screw in the hinges (1) and
the counter-magnet (6) provided with the appliance, at
the right level (Fig. B).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
If the door has to be opened from left to right, invert the
position of the plates (7), the magnet (4) and the plate
(5) (Fig. B and E). Mount the counter-magnet (6) and
the hinges (1) as previously described.
Recommendations regarding the construction and fit-
ting of a base when the installation requires an integra-
ted appliance to be raised.
4
6
Graphic F
5 mm Hardwood strip
8
40
Additional pieces
of timber should run
100
from front to back
600-605
D
Front view
Caution! Do not remove the screw 8!
Where the appliance has been raised by mounting onto
a wooden base provided by the installer. The material
used to construct the base should have anon slip sur-
face, be water repellent and if possible be one solid
piece.
If it is not possible to use one solid piece, due to the
additional height required, ensure that any additional
strips of timber are glued and screwed to the underside
of the base (see Fig. F).
d) Counter-magnet (6)
The appliance is prearranged for a magnetic closure of
the door.
To enable a correct operation of this device, it is neces-
sary to screw the counter-magnet (6) (steel disk + rub-
ber ring) into the inner side of the door. Its position
must correspond to the magnet (4) on the appliance
(see picture D).
Graphic G
600-605
6
1
490
4 5
7
3
95
2
8
Front edge
E
50
Top view
Caution! Do not remove the screw 8!
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill four fixing holes see Fig. G
Fix the base firmly to the floor using four appropriate
countersunk screws (see Fig. H).
With the appliance installed adjust all four feet ensuring
the machine is stable, and a clearance of approximately
5 mm is left between the top of the machine and the un-
derside of the worktop.
Position the base into the recess with its front edge as
far forward as the adjoining plinth line will allow.
The reason for placing the base in this position is to al-
low a small strip of beading to be fitted in front of the
appliance feet.
A final check for stability should be carried out with the
machine on spin with a load, this will identify the need
for any further fine adjustment to the feet.
Graphic H
A strip of beading approximately 605 mm W, x 5 mm H,
x 25 mm D must be screwed down into the base directly
in front of the machine’s feet, this will provide addition-
al security.
If required an additional door magnet, part number
1242394-00/3 and disc, part number 1242393-00/5 are
available from spare parts.
Hardwood strip
5 mm x 25 mm
5 x 25 x 605
490
600-605
Environment concerns
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
The symbol on the product or on its packaging
indicates that this product may not be treated as
Ecological hints
To save water, energy and to help protect the environment,
we recommend that you follow these tips:
• Normally soiled laundry may be washed without pre-
washing in order to save detergent, water and time (the
environment is protected too!).
• The machine works more economically if it is fully loa-
ded.
household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
information about recycling of this product, please contact
your local council, your household waste disposal service
or the shop where you purchased the product.
• With adequate pre-treatment, stains and limited soiling
can be removed; the laundry can then be washed at a
lower temperature.
Packaging materials
• Measure out detergent according to the water hard-
ness, the degree of soiling and the quantity of laundry
being washed.
The materials marked with the symbol
>PE<=polyethylene
>PS<=polystyrene
are recyclable.
>PP<=polypropylene
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|