User
manual
Washing
Machine
ZWF 14380 W
ZWF 14380 S
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety information
In the interest of your safety and to ensure
the correct use, before installing and first
using the appliance, read this user manual
carefully, including its hints and warnings.
To avoid unnecessary mistakes and
accidents, it is important to ensure that all
people using the appliance are thoroughly
familiar with its operation and safety
features. Save these instructions and make
sure that they remain with the appliance if it
is moved or sold, so that everyone using it
through its life will be properly informed on
appliance use and safety.
● Always unplug the appliance and turn off the
water supply after use, cleaning and
maintenance.
● Under no circumstances should you attempt
to repair the machine yourself. Repairs
carried out by inexperienced persons may
cause injury or serious malfunctioning.
Contact your local Service Centre. Always
insist on genuine spare parts.
Installation
● This appliance is heavy. Care should be
taken when moving it.
● When unpacking the appliance, check that it
is not damaged. If in doubt, do not use it and
contact the Service Centre.
● All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this is
not adhered to. See relevant section in the
user manual.
● After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable.
● If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to
circulate freely under the appliance.
● Always be sure, that there is no water
leakage from hoses and their connections
after the installation.
General safety
● It is dangerous to alter the specifications or
attempt to modify this product in any way.
● During high temperature wash programmes
the door glass may get hot. Do not touch it!
● Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
● Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp
material can cause extensive damage and
must not be placed into the machine.
● Only use the advised quantities of fabric
softener and detergent. Damage to the fabric
can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
● Wash small items such as socks, laces,
washable belts etc in a washing bag or
pillow case as it is possible for such items to
slip down between the tub and the inner
drum.
● Do not use your washing machine to wash
articles with whalebones, material without
hems or torn material.
● If the appliance is installed in a location
subject to frost, please read the «dangers of
freezing» chapter.
● Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
● Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
● Make sure that children or pets do not climb
into the drum. To prevent children or pets
becoming trapped inside the drum, the
machine incorporates special feature.
Use
● This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
● Only wash fabrics which are designed to be
machine washed. Follow the instructions on
each garment label.
● Do not overload the appliance. See the
relevant section in the user manual.
● Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and
treat stains such as paint, ink, rust, and
grass before washing. Underwired bras must
NOT be machine washed.
● Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
To activate this device, To disable this device
rotate the button
and restore the
(without pressing it)
inside the door
possibility of closing the
door, rotate the button
anti-clockwise until the
groove is vertical.
clockwise until the
groove is horizontal. If
necessary use a coin.
● Never pull the power supply cable to remove
the plug from the socket; always take hold of
the plug itself.
● Never use the washing machine if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the washing machine is accessible.
Child safety
● This washing machine is not intended for
use by young children or infirm persons
without supervision.
● Young children should be supervised to
ensure that they do not play with the
appliance.
● The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children -
danger of suffocation! Keep them out of
children’s reach
● Keep all detergents in a safe place out of
children’s reach.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Description of the appliance
1
Detergent dispenser drawer
1
2
2
Control panel
3
Door opening handle
4
Drain pump
5
Adjustable feet
3
4
5
Detergent dispenser drawer
Prewash
Wash
Fabric Softener
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Control panel and functions
8
1
2
3
4
5
6
7
●
●
The programme selector dial allows you to select a programme
and/or to switch the machine on/off. It can be turned either
Programme selector dial and
On/Off switch
1
2
6
clockwise or anticlockwise. The light of button
starts to flash.
Press this button repeatedly to change the spin speed, if you
want your laundry to be spun at a speed different from the one
proposed by the washing machine or to select the Night Cycle
Spin reduction button
and Rinse Hold
. The relevant light will light up.
●
By pressing this button, you can select only one of the following
option: Prewash, Intensive, Super Quick (see the relevant
chapter «Operating sequence»). The relevant light will light up.
Options button
3
4
●
●
By pressing this button, the machine performs some additional
rinses.
Extra Rinse button
The display shows the following information: duration of the
selected programme, delayed start, incorrect option selection,
alarm codes, child lock activated, heating phase and end of
programme.
Display
5
6
●
●
This button allows you to start the selected programme; the
corresponding green pilot light stops flashing.
It also interrupts a programme which is running, the
corresponding green pilot light starts to flash.
Start/Pause button
●
●
By pressing this button the wash programme can be delayed
from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to
a maximum of 20 hours.
Delay Start button
Indicator lights
7
8
The different pilot lights illuminate depending on the running
programme phase:
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Programme table
Programme/
Temperature
Description of
programme
Type of laundry
Options
Main wash, rinses
Long spin at the max
speed
Max load: 7 kg
*Reduced Load: 3.5 kg
Spin red.
Cottons
95°
White cotton (normally
soiled cotton items).
Prewash, Intensive,
Super Quick, Extra rinse
White and fast
coloured cotton
(normally soiled cotton
items)
Main wash, rinses
Long spin at the max
speed
Cottons
60° Eco
Spin red.
Prewash, Extra rinse
Max load: 7 kg
Main wash, rinses, long
spin at the max speed
Max load: 7 kg
*Reduced Load: 3.5 kg
Spin red.
Cottons
60° - 40°
Coloured cotton lightly
soiled
Prewash, Intensive,
S. Quick, Extra rinse
Main wash, rinses
Long spin at the max
speed
Cottons
40° Eco
Coloured cotton lightly
soiled
Spin red.
Prewash, Extra rinse
Max load: 7 kg
Main wash
rinses
Short spin 900 rpm
Max load: 3.5 kg
*Reduced Load: 1.5 kg
Spin red.
Synthetics
50° - 40°
Synthetic or mixed
fabrics
Prewash, Intensive,
Super Quick
Extra rinse
Main wash
rinses
Short spin 900 rpm
Max load: 1 kg
Synthetic or mixed
fabrics to be gently
washed and spun.
Synthetics
Easy iron 40°
Spin red.
Prewash, Extra rinse
Main wash,
rinses
Short spin 700 rpm
Max load: 3.5 kg
*Reduced Load: 1.5 kg
Delicates
40° - 30°
Delicate fabrics, for
example curtains.
Prewash, Super Quick
Intensive, Extra Rinse
* If you select the SUPER QUICK option by pressing the relevant button, we recommend you, to
reduce the maximum load as indicated in the table above. Full loading is possible however with
somewhat reduced cleaning results.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Programme table
Programme/
Temperature
Description of
programme
Type of laundry
Options
Programme for wool
«Pure new wool, non-
shrink, machine
Main wash
rinses
Short spin 900 rpm
Max load: 2 kg
Wool
40°
Spin red.,
,
,
washable» label.
Main wash, rinses
Short spin 900 rpm,
Max load: 2 kg
Handwash
30° - Cold
Special programme for
hand washing fabrics
Spin red.,
Main Wash, rinses
Short spin 700 rpm
Max load: 2 kg
Mini 30’
30°
Short cycle for lightly
soiled fabrics
Main wash, rinses
Short spin 700 rpm
Max load: 1 kg
Silk
30°
Silk items to be gentle
washed and spun.
,
Main Wash, rinses
Short spin 900 rpm
Max load: 1 pair
Sport
Short cycle for 1 pair of
sport shoes
Spin Red.
Shoes 40°
Prewash, Extra rinse
Prewash at 30°C
Main wash, rinses
Short spin 900 rpm,
Max load: 2.5 kg
Spin red.,
,
Programme for heavily
soiled synthetics items
Sport 40°
Rinse
Extra rinse
rinses
Long spin at the max
speed
Separate rinse cycle for
hand washed items of
cotton.
Spin red.
Extra rinse
Max load: 7 kg
For emptying out the last
rinse water in
programmes with the
Rinse Hold or Night
Cycle option.
Drain
Spin
Draining of water
Drain and long spin at the
max speed
Separate spin for
cottons.
Spin red.
Max load: 7 kg
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Programme information
This programme can be selected for slightly or normally soiled
cotton items. The temperature will decrease and the washing time
will be extended. This allows you to obtain a good washing
efficiency whilst saving energy.
Cottons Eco
Washing programme for machine washable wool as well as for hand
washable woollens and delicate fabrics with the «hand washing»
Wool and
care symbol
.
Note: A single or bulky item may cause imbalance. If the appliance
doesn’t perform the final spin phase, add more items, redistribute
the load manually and then select the spinning programme.
Handwash
By selecting this programme, the laundry is gently washed and spun
to avoid any creasing. In this way ironing is easier. Furthermore the
machine will perform additional rinses.
Easy Iron
Rinse
With this programme it is possible to rinse and spin cotton garments
which have been washed by hand.
The machine performs 3 rinses, followed by a final spin at maximum
speed. The spin speed can be reduced by pressing the relevant
button.
For emptying out the water of the last rinse in programmes with the
Rinse Hold or Night Cycle option.
Firstly, turn the programme selector dial to «Off», then select
Drain
6
programme Drain and press the button
.
Separate spin for hand washed garments and after programmes
with Rinse Hold or Night Cycle option. Before selecting this
programme the selector dial must be turned to «Off». You can
choose the speed by pressing the relevant button to adapt it to the
fabrics to be spun.
Spin
With this programme it is possible to wash one pair of sport shoes.
The shoes would be gently washed and spun. Washing temperature
40°C. Note! Do not wash your sport shoes together with laundry.
Sport shoes 40°
This programme is suitable for washing heavily soiled sport items of
synthetic fabrics. The machine will automatically add a prewash
phase before the main wash to eliminate mud stains.
Sport 40°
Note ! We recommend that you do not put the detergent into the
compartment
reduced.
of the detergent drawer. The spin speed is
To reset a programme and to switch off the machine turn the
selector dial to «Off».A new programme can now be selected.
Off = Cancelling
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Washing hints
Sorting the laundry
Maximum loads
Follow the wash code symbols on each
Recommended loads are indicated in the
programme charts.
garment label and the manufacturer’s washing
instructions. Sort the laundry as follows: whites,
coloureds, synthetics, delicates, woollens.
General rules:
Cotton, linen: drum full but not too tightly
packed;
Temperatures
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no more
than one third full.
Washing a maximum load makes the most
efficient use of water and energy.
For heavily soiled laundry, reduce the load
size.
for normally soiled white cottons
90° or 95°
50°/60°
and linen (e.g. tea cloths, towels,
tablecloths, sheets...)
for normally soiled, colour fast
garments (e.g. shirts, night
dresses, pyjamas....) in linen,
cotton or synthetic fibres and for
lightly soiled white cotton (e.g.
underwear).
Laundry weights
The following weights are indicative:
for delicate items (e.g. net
curtains), mixed laundry including
30°-40°-Cold synthetic fibres and woollens
bearing the label «pure new wool,
bathrobe
napkin
quilt cover
sheet
pillow case
tablecloth
1200 g
100 g
700 g
500 g
200 g
250 g
200 g
100 g
200 g
100 g
600 g
200 g
500 g
100 g
100 g
machine washable, non-shrink».
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Make sure that no metal objects are left in
the laundry (e.g. hair clips, safety pins,
pins). Button up pillowcases, close zip
fasteners, hooks and poppers. Tie any belts
or long tapes.
towelling towel
tea cloth
night dress
ladies’ briefs
man’s work shirt
man’s shirt
man’s pyjamas
blouse
men’s underpants
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Removing stains
Detergents and additives
Stubborn stains may not be removed by just
Good washing results also depend on the
water and detergent. It is therefore advisable to choice of detergent and use of the correct
treat them prior to washing.
quantities to avoid waste and protect the
environment. Although biodegradable,
detergents contain substances which, in large
quantities, can upset the delicate balance of
nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
All commonly available washing machine
detergents may be used in this appliance:
● powder detergents for all types of fabric,
● powder detergents for delicate fabrics (60°C
max) and woollens,
● liquid detergents, preferably for low
temperature wash programmes (60°C max)
for all types of fabric, or special for woollens
only.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will have already been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash
programme.
If using concentrated powder or liquid
detergents, a programme without prewash
must be selected.
The washing machine incorporates a
recirculation system which allows an optimal
use of the concentrated detergent.
Pour liquid detergent into the dispenser drawer
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone (*), lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Remove
any residual marks from white fabrics with
bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
compartment marked
the programme.
just before starting
Any fabric softener or starching additives must
be poured into the compartment marked
before starting the wash programme.
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the
detergent dispenser drawer.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
(*) do not use acetone on artificial silk.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Quantity of detergent to be used
Degrees
Level Characteristic
The type and quantity of detergent will depend
on the type of fabric, load size, degree of
soiling and hardness of the water used.
Water hardness is classified in so-called
«degrees» of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company, or from your local authority.
Follow the product manufacturers’ instructions
on quantities to use.
German
°dH
French
°T.H.
1
2
3
4
soft
medium
hard
0-7
0-15
16-25
26-37
> 37
8-14
15-21
> 21
very hard
Degrees of water hardness
Follow the product manufacturers’ instructions
on quantities to use.
Use less detergent if:
● you are washing a small load,
● the laundry is lightly soiled,
● large amounts of foam form during washing.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Before the first use
Child safety lock
WARNING!
This device function allows you to leave the
appliance unattended without having the worry
that children might be injured by or cause
damage to the appliance.
Ensure that the electrical and water
connections comply with the installation
instructions.
This function remains enabled also when the
washing machine is not working.
IMPORTANT!
Remove the polystyrene block and any
material from the drum.
There are two different ways to set this option:
●
before pressing the button 6 : it will be
impossible to start the machine.
after pressing the button 6 : it will be
impossible to change any other programme
or option.
IMPORTANT!
Before the first wash run a cotton cycle at
95°C or 90°C, without any laundry in the
machine, to remove any manufacturing residue
from the drum and tub. Pour 1/2 a measure of
detergent into the dispenser drawer and start
the machine.
●
To enable (or disable) this option press
simultaneously for about 6 seconds the buttons
3 and 4 until the paddle icon
appears
Acoustic signals
(disappears) on (from) the display .
The machine is provided with an acoustic
device, which sounds in the following cases:
Stand by mode
If your laundry is not removed within 10
minutes after the programme is finished, the
backlight of the display switches off and the
energy saving system will be enabled.
Only the pilot light of the button
to indicate that you must switch the appliance
●
at the end of the cycle
if there is a fault
●
By pressing buttons 2 and 3
simultaneously for about 6 seconds,the
acoustic signal is deactivated (except if there is
a fault). By pressing these 2 buttons again, the
acoustic signal is reactivated.
6
still blinks
off.
If you press any button, the appliance will
come out from the energy saving status and
you could set another washing programme or
switch the appliance off.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Operating sequence
IMPORTANT!
If you turn the programme selector dial to
another programme when the machine is
Load the laundry
Open the door by
carefully pulling the
door handle outwards.
Place the laundry in the
drum, one item at a
time, shaking them out
6
working, the red pilot light of button
will
flash 3 times and the message Err is displayed
to indicate a wrong selection. The machine will
not perform the new selected programme.
Select the spin speed or Night Cycle or
Rinse Hold option by pressing the button
2
When selecting a programme, the light
corresponding to the maximum speed allowed
for that programme will illuminate (refer to the
section «Programme table» for the maximum
allowed by each cycle spin speed).
as much as possible. Close the door.
Measure out the detergent and the fabric
softener
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
speed different from the one proposed by the
appliance.
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required,
pour it into the main wash compartment
and, if you wish to carry out a programme with
the prewash phase, pour it into the
Night Cycle
: by selecting this option, the
machine will not drain the water of the last
rinse, so as not to crease the laundry. As all
spinning phases are suppressed, this washing
cycle is very quiet and it can be selected at
night or in times with a more economical power
rate. On some programmes, the rinses will be
performed with more water.
When the programme has finished, the display
shows a flashing zero «0.00» but the door
remains locked to indicate that the water must
be emptied out.
compartment marked
.
If required, pour fabric softener into the
compartment marked
(the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
Select the required programme by turning
1
the programme selector dial (
)
6
The green light of the button
starts to flash.
Rinse Hold
: by selecting this option the
The selector dial can be turned either
clockwise or anticlockwise.
water of the last rinse is not emptied out to
prevent the fabrics from creasing.
When the programme has finished, the display
shows a flashing zero «0.00» but the door
remains locked to indicate that the water must
be emptied out.
Turn to position «Off» to Reset programme /
Switch OFF of the machine.
At the end of the programme the selector
dial must be turned to position «Off», to
switch the machine off.
To empty out the water, see the paragraph
«At the end of the cycle».
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Operating sequence
Select the desired option by pressing the
After the programme
has started, the time
remaining is updated
every minute.
3
button
Press this button repeatedly, to select one of
the available options. The relevant light will
light up.
2.05
Prewash: select this option if you wish your
laundry to be prewashed at 30°C before the
main wash. The prewash ends with a short
spin in programmes for cotton and synthetic
fabrics, whereas in the programmes for
delicate fabrics the water is only drained.
Delayed start
The selected delay (20 hours max) set by
pressing the relevant button appears on the
display for about 3 seconds, then the duration
of the previously selected programme is
displayed.
Intensive: this option can be selected for
heavily soiled laundry: the washing intensity
will be increased and the washing time will be
prolonged by a few minutes depending on the
selected type of fabric.
The delay time value
decreases by one unit
every hour and then,
when 1 hour remains,
the time decreases
15 h
Super Quick: a very short cycle for slightly
soiled items that have been used or worn for a
short time.
The washing time will be reduced according to
the type of fabric and the selected temperature.
We recommended that you to reduce the
laundry load (see the programmes table).
every minute.
Incorrect option selection
If an option which is not
compatible with the set
wash programme is
selected, the message
Select the Extra Rinse option by pressing
the button
The machine performs some additional rinses.
This option is recommended for people who
are allergic to detergents, and in areas where
the water is very soft.
Err is displayed for a
few seconds and the red
starts flashing.
4
6
light of the button
Alarm codes
In the event of operating
problems, some alarm
codes can be displayed,
for example E20 (see
paragraph “What do
if...”).
Display ( 5 )
E20
The display shows the following information:
Duration of the selected programme
After selecting a programme, the duration is
displayed in hours and minutes (for example
2 .05 ). The duration is calculated automatically
on the basis of the maximum recommended
load for each type of fabric.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Operating sequence
Heating phase
Selecting the delayed start:
●
●
●
Select the programme and the required
options.
Select the delay start by pressing the button
7 .
Press the button 6 : the machine starts its
countdown.
During the washing
cycle the display shows
a temperature icon to
indicate that the
2.05
appliance has started
the heating phase of the water in the tub.
The programme will start after the selected
delay has expired.
Start the programme by pressing the button
6
Cancelling the delayed start:
You can cancel the delay time at any moment,
before you press the button 6 .
If you have already pressed it, and you wish to
cancel the delay time, proceed as follows:
To start the selected programme, press this
button; the corresponding green pilot light
stops flashing.
The «Wash» and «Door» lights illuminate to
indicate that the appliance starts operating and
the door is locked.
• set the washing machine to PAUSE by
pressing the button 6 ;
To interrupt a programme which is running,
• press the button 7 repeatedly until the
symbol 0’ is displayed.
6
press the button
: the corresponding green
pilot light starts to flash. To restart the
programme from the point at which it was
interrupted, press this button again.
If you have chosen a delayed start, the
machine will begin the countdown.
• press the button 6 again to start the
programme.
IMPORTANT!
• The selected delay can be changed only
after selecting the washing programme
again.
• The door will be locked throughout the delay
time. If you need to open the door, you must
first set the washing machine to PAUSE by
pressing the button 6 and then wait a few
minutes until the «Door» light has gone off.
After you have closed the door, press the
button 6 again.
IMPORTANT!
If an incorrect option is selected, the red pilot
light of this button flashes 3 times and the
message Err is displayed for a few seconds.
Select the Delay Start by pressing the
7
button
Before you start the programme, if you wish to
delay the start, press the button 7 repeatedly,
to select the desired delay.
The selected delay time value (up to 20 hours)
will appear on the display for a few seconds,
then the duration of the programme will appear
again.
The Delay Start cannot be selected with
Drain programme.
Indicator lights ( 8 )
After having pressed the button 6 , the
«Wash» pilot light illuminates and stays on
while the machine is working. At the end of
any cycle it goes off.
You must select this option after you have set
the programme and before you press the
button 6 .
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Operating sequence
When the programme has finished, the «End»
pilot light illuminates and at the same time the
light of the button 6 goes off. If there is water
left in the tub, the «Door» light illuminates: the
door remains locked.
The «Door» pilot light indicates if the door can
be opened:
• light on: the door cannot be opened.
The appliance is operating or there is water
left in the tub. Attention! If the door is locked
do not try to open it!
Opening the door after the programme has
started
First set the machine to pause by pressing the
button 6 .
If the «Door» light flashes after a few minutes
the door can be opened. If this light remains lit,
this means that the machine is already heating
or that the water level is too high.
In this case the door can not be opened.
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to «Off». After about a
few minutes the door can be opened (pay
attention to the water level and
• light off: the door can be opened.
The washing programme is finished.
• flashing light: the door is opening.
temperature!).
Altering an option or a running programme
It is possible to change a few options before
the programme carries them out.
After this procedure, it will be necessary to set
the programme and the options again and then
to press button 6 .
Before you make any change, you must pause
the washing machine by pressing the button
At the end of the programme
6
The machine stops automatically. On the
display will appear a flashing «0.00» and the
door can be opened.
If the «Rinse hold» or «Night Cycle» option has
been selected, the display will show a flashing
«0.00» and the door remains locked to
indicate that the water must be emptied out
before opening the door.
.
Changing a running programme is possible
only by resetting it. Turn the programme
selector dial to «Off» and then to the new
programme position. Start the new programme
by pressing the button 6 again.
The washing water in the tub will not be
emptied out.
Interrupting a programme
To empty out the water proceed as follows:
Press the button 6 to interrupt a programme
which is running, the corresponding light starts
to flash. Press this button again to restart the
programme.
1.turn the programme selector dial to «Off»
2.select the Drain or Spin programme
3.reduce the spin speed if needed, by pressing
the relevant button
Cancelling a programme
4.press the button 6
to start the selected
Turn the selector dial to Off to cancel a
programme which is running. You can now
select a new programme.
programme
5.at the end of programme, only the «End»
light illuminates. Now it is possible to open
the door.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Turn the programme selector dial to «Off» to
switch the machine off.
Remove the laundry from the drum and
carefully check that the drum is empty.
If you do not intend to carry out another wash,
close the water tap. Leave the door open to
prevent the formation of mildew and
unpleasant smells.
Care and cleaning
IMPORTANT!
External cleaning
You must DISCONNECT the appliance from
the electricity supply, before you can carry out
any cleaning or maintenance work.
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
Descaling
The water we use normally contains lime. It is
a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder
manufacturer's instructions. This will help to
prevent the formation of lime deposits.
Maintenance Wash
With the use of low temperature washes it is
possible to get a build up of residues inside the
drum.
We recommend that a maintenance wash be
performed on a regular basis.
To aid cleaning, the top part of the additive
compartment should be removed.
Remove the drawer by pressing the catch
downwards and by pulling it out. Flush it out
under a tap, to remove any traces of
accumulated powder.
To run a maintenance wash:
●
●
●
The drum should be empty of laundry.
Select the hottest cotton wash programme.
Use a normal measure of detergent, must be
a powder with biological properties.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Cleaning the drawer recess
Having removed the
●
●
Remove any objects from the pump impeller
by rotating it.
Refit the cap on the emergency emptying
hose and place the latter back in its seat.
drawer, use a small
brush to clean the
recess, ensuring that all
washing powder
residue is removed from
the upper and lower
●
●
Screw the pump cover
fully in.
Close the pump door.
part of the recess.
Replace the drawer and run the rinse
programme without any clothes in the drum.
I
Cleaning the pump
The pump should be inspected if
MPORTANT!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When
replacing the cover, ensure it is securely
retightened so as to stop leaks and young
children being able to remove it.
●
the machine does not empty and/or spin
the machine makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump.
●
Proceed as follows:
●
Disconnect the appliance.
If necessary wait until the water has cooled
down.
●
●
Open the pump door.
Cleaning the water inlet filter
If your water is very hard or contains traces of
lime deposit, the water inlet filter may become
clogged.
It is therefore a good idea to clean it from time
to time.
●
Place a container close
to the pump to collect
any spillage.
Pull out the emergency
emptying hose, place it
in the container and
remove its cap.
●
Turn off the water tap.
Unscrew the water inlet
hose. Clean the filter
using a hard bristle
brush. Refit the inlet
●
When no more water comes out, unscrew the
pump cover and remove it. Always keep a
rag nearby to dry up spillage of water when
removing the cover.
hose.
The dangers of freezing
If the machine is exposed to temperatures
below 0°C, certain precautions should be
taken.
●
Turn off the water tap.
Unscrew the inlet hose.
●
Download from Www.Somanuals.com. All Manuals Search And Download.
19
●
●
●
Place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain out.
Screw the water inlet hose back on and
reposition the emergency emptying hose
after having put the cap on again.
When you intend to start the machine up
again, make sure that the room temperature
is above 0°C.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
●
●
●
pull out the plug from the power socket;
close the water tap;
if necessary, wait until the water has cooled
down;
●
●
open the pump door;
place a bowl on the floor and place the end
of the emergency emptying hose into the
bowl. Remove its cap. The water should
drain by gravity into the bowl. When the bowl
is full, put the cap back on the hose. Empty
the bowl. Repeat the procedure until water
stops flowing out;
●
●
●
clean the pump if necessary as previously
described;
replace the emergency emptying hose in its
seat after having plugged it;
screw the pump cover again and close the
door.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
What to do if...
IMPORTANT!
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily
without calling out an engineer. Before contacting your local Service Centre, please carry out the
checks listed below.
During machine operation it is possible that the red pilot light of the button 6 flashes, the buzzer
sounds and one of the following alarm codes appears on the display to indicate that the machine
is not working.
●
●
●
E10: problem with the water supply
E2 0: problem with water draining
E40: door open.
Once the problem has been eliminated, press the button 6 to restart the programme. If after all
checks, the problem persists, contact your local Service Centre.
Malfunction
Possible Cause / Solution
The door has not been closed. E40
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse or the fuse in the plug has blown.
• Replace the fuse.
The washing machine does not start:
The selector dial is not correctly positioned and the
button 6 has not been pressed.
• Please turn the selector dial and press the button
6 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel
the delay start.
The Child Safety Lock function has been activated.
• Deactivate this function.
The water tap is closed. E10
• Open the water tap.
The inlet hose is squashed or kinked. E10
• Check the inlet hose connection.
The machine does not fill:
The filter in the inlet hose is blocked. E10
• Clean the water inlet hose filter.
The door is not properly closed. E40
• Close the door firmly.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Malfunction
Possible Cause / Solution
The end of the drain hose is too low.
• Refer to relevant paragraph in «water drainage»
section.
The machine fills then empties
immediately:
The drain hose is squashed or kinked. E2 0)
• Check the drain hose connection.
The drain pump is clogged. E2 0
• Clean the drain pump.
The machine does not empty and/or
does not spin:
The option
selected.
or «Night Cycle» has been
«Rinse hold»
• Select the draining or spinning programmes.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Too much detergent or unsuitable detergent (creates
too much foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose; check to see if it is
damp.
There is water on the floor:
• Check the water inlet hose connection.
The inlet or drain hose is damaged.
• Replace it with a new one.
The cap on the emergency emptying hose has not
been replaced after cleaning the pump.
• Refit the cap on the emergency emptying hose and
place the latter back in its seat.
Too little detergent or unsuitable detergent has been
used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to
washing.
• Use commercial products to treat the stubborn
stains.
Unsatisfactory washing results:
The correct temperature was not selected.
• Check if you have selected the correct
temperature.
Excessive laundry load.
• Reduce the laundry load.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Malfunction
Possible Cause / Solution
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait a few minutes until the «Door» light has gone
off.
The door will not open:
There is water in the drum.
• Select drain or spin programme to empty out the
water.
The transit bolts and packing have not been
removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted.
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
The machine vibrates or is noisy:
Maybe there is very little laundry in the drum.
• Load more laundry.
The electronic unbalance detection device has cut in
because the laundry is not evenly distributed in the
drum. The laundry is redistributed by reverse rotation
of the drum. This may happen several times before
the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not
evenly distributed in the drum, the machine will not
spin. In this case, redistribute the load manually and
select the spin programme.
Spinning starts late or the machine
does not spin:
●
Redistribute the laundry.
●
If the load is very small, add more items, redistribute
the load manually and then select the spinning
programme.
The machine is fitted with a type of motor which
makes a different noise compared with other
traditional motors. This new motor ensures a softer
start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of
the machine.
The machine makes an unusual noise
No water is visible in the drum
Machines based on modern technology operate very
economically using very little water without affecting
performance.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
If you are unable to identify or solve the problem, contact our
service centre.
Before telephoning, make a note of the model, serial number
and purchase date of your machine: the Service Centre will
require this information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Technical data
Dimensions
Width
60 cm
Height
85 cm
63 cm
Depth (including the porthole)
Electrical connection Voltage -
Overall power - Fuse
Information on the electrical connection is given on the rating
plate on the inner edge of the appliance door
Water supply pressure
Maximum Load
Minimum
Maximum
0,05 MPa
0,8 MPa
Cotton
Synthetics
Delicates
Woollens and handwash
70 kg
3.5 kg
3.5 kg
2.0 kg
Spin Speed
Maximum
0
1400 rpm
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Consumption values
Programme
duration
(in hours and
minutes)
Programme
Energy
consumption
(in kWh)
Water
consumption
(in litres)
Cottons 95°C
2.2
1.19
1.4
65
52
62
57
Cottons 60° Eco(*)
Cottons 60°C - 40°C
Cottons 40° Eco
1.2
Delicates 40°C - 30°C
Wool 40°C
0.55
0.35
0.25
58
52
52
Handwash 30°C - Cold
Information
The consumption data shown on this chart is to
be considered purely indicative, as it may vary
depending on the quantity and type of laundry,
on the inlet water temperature and on the
ambient temperature. It refers to the highest
temperature for each wash programme.
(*) The “Cottons 60° Eco” is the reference
programme with a load of 7 kg for the data
entered in the energy label, in compliance
with EEC 92/75 standards.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Installation instruction
Unpacking
All transit bolts and packing must be removed
before using the appliance.
5. Remove the bracket D, refit the six smaller
bolts C and slide out the relevant plastic
spacer E.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
6. Remove the polystyrene block fitted on the
door seal.
7. Fill the smaller upper hole and the two large
ones with the corresponding plastic plug
caps supplied in the bag containing the
instruction booklet.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable, the inlet
and the draining hoses from the hose
holders on the rear of the appliance.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units.
A
C
Water inlet
B
The inlet hose is already screwed on the back
of the appliance.
B
C
1. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure
to tighten the ring nut again to prevent
leaks.
3. With a suitable spanner unscrew and
remove the central rear bolt A.
4. Unscrew and remove the two large rear
bolts B and the six smaller bolts C.
Do not place the inlet hose downwards. Angle
the hose to the left or right depending on the
position of your water tap (see picture).
E
C
D
C
HEC0006
Download from Www.Somanuals.com. All Manuals Search And Download.
26
2. This appliance must be connected to a
cold water supply. Connect the hose to a
tap with a 3/4” thread. The inlet hose must
not be lengthened. If it is too short and you
do not wish to move the tap, you will have
to purchase a new, longer hose specially
designed for this type of use..
Special
Off
Cottons
S
p
o
r
t
4
0
°
95°
3h
6h
9h
S
p
o
r
t
S
h
o
e
s
4
0
°
60° Eco
60°
1000
900
Silk
M
i
n
i
3
0
'
4
0
°
E
c
o
700
Prewash
Intensive
Wash
Door
End
Cold
Hand
40°
Synthetics
50°
Super
Quick
Wash
30°
ool
1
0
0
0
6
k
g
Options
E
x
t
r
a
R
i
n
s
e
Start/Pause
Spin
W
40°
aIron 40°
Spin
Drain
40°
R
i
n
s
e
3
0
°
ZWF10070W
Delicates
38 mm (1.5”)
standpipe
diameter
NOTE
Firstly form a hook in the end of the drain
hose using the «U» piece supplied. Place the
drain hose into your standpipe, which should
have an internal diameter of approximately
38mm thus ensuring there is an air break
between the drain hose and standpipe.
When discharging into a standpipe ensure that
the top of the standpipe is no more than 90
cm (35.4'') and no less than 60 cm (23.6'')
above floor level.
Installation should
comply with local
water authority and
building regulations’
requirements.
The appliance must be connected to a cold
water supply.
A minimum water pressure of 0.05 MPa (0.5
bar) is required for safe operation of the
appliance.
Special
Spor
t
40°
Off
95°
Cottons
3h
6h
9h
Spor
t
S
h
o
e
s
4
0
°
60° Eco
60°
1000
900
Silk
Mini 30'
Cold
4
0
°
E
c
o
700
Prewash
Intensive
Wash
Door
End
40°
Synthetics
50°
Hand
Super
Quick
W
ash
1
0
0
0
6
k
g
30°
ool
Spin
Options
E
x
t
r
a
R
i
n
s
e
Start/Pause
W
40°
ay Ion 40°
Spin
Drain
40°
Rinse 30° Delicates
ZWF10070W
If you cannot make the cold water connection
direct from the rising mains, you may be able
to operate the appliance from your cold water
storage system.
There should be a minimum vertical distance of
5.02m (16.5 ft) between the appliance’s inlet
and the bottom of the water storage tank.
The drain hose may be extended to a
maximum of 4 metres. An additional drain
hose and joining piece is available from your
local Service Force Centre. The joining piece
must have an internal diameter of 18mm.
Water drainage
This appliance is designed to be permanently
plumbed into your home's drainage system
using one of the following methods.
If your drain hose
looks like this (see
below) you do not
require the «U»
piece. Just push the
hose firmly into the
standpipe.
1. Into a drainage standpipe.
“U” piece
supplied
2. Onto a sink outlet spigot.
If the outlet spigot has not been used before,
remove any blanking plug that may be in
place.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Special conditions
If the floor is carpeted or covered with crumbly
or soft material, insert a rigid support base
under the feet to prevent noise, vibration or
displacement. The base should protrude a few
centimetres beyond the edges of the machine.
Loop
WARNING!
Push the drain hose onto the spigot and secure
with a clip, ensure a loop is formed in the drain
hose (see diagram) to prevent waste from the
sink entering the washing machine.
The machine should NOT be placed on deep
pile carpeting.
NOTE
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of a breakdown.
Important!
Before connecting the machine to new
pipework or to pipework that has not been
used for some time, run off a reasonable
amount of water to flush out any debris that
may have collected in the pipes.
In the interest of the environment
Washing machines should be connected to the
FOUL drainage system, the water will then be
taken to a sewage works for treatment before
being discharged safely into a river. It is
essential that these appliances are not
connected to the surface water drainage
system as this water is discharged directly into
a river or stream and may cause pollution.
If you require any further advice please contact
your local water authority.
Levelling
Level the washing machine by raising or
lowering the feet. The feet may be tight to
adjust as they incorporate a self locking nut,
but the machine MUST be level and stable.
If necessary, check the
setting with a spirit
level.
SHOWER
Any necessary adjustment can be made with a
spanner. Accurate levelling prevents vibration,
noise and displacement of the machine during
operation.
SINK TOILET
BATH
BIDET
WASHING
MACHINE
DISHWASHER
Never place cardboard, wood or similar
materials under the machine to compensate for
any unevenness in the floor.
RAINWATER
'RUN-OFF'
FOUL DRAIN
Some vibration is inevitable, especially if
mounted on a wooden floor.
Sprung wooden floors are particularly
susceptible to vibration. For advice, consult a
builder. If possible, always place the machine
on a solid floor.
SURFACE WATER
FOUL SEWERS
DRAINS & SEWERS
SEWAGE
TREATMENT
WORKS
UNTREATED
DISCHARGE
TREATED
DISCHARGE
RIVER
RIVER
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Electrical connection
The wire coloured blue must be connected to
the terminal marked «N» or coloured black.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
The wire coloured brown must be connected to
the terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp
must be secure over the outer sheath.
WARNING!
This appliance must be earthed.
The manufacturer declines any liability
should this safety measure not be
observed.
Before switching on, make sure the electricity
supply voltage is the same as that indicated
on the appliance’s rating plate.
WARNING!
A cut off plug inserted into a 13 amp socket
is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely. Should the appliance power supply
cable need to be replaced, this must be
carried out by our Service Force Centre.
IMPORTANT!
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
The power supply cable must be easily
accessible after installing the appliance.
Permanent connection
The appliance is supplied with a 13amp plug
fitted. In the event of having to change the
fuse in the plug supplied, a 13amp ASTA
approved (BS1363/A) fuse must be used.
In the case of permanent connection it is
necessary that you install a double pole switch
between the appliance and the electricity
supply (mains), with a minimum gap of 3mm
between the switch contacts and of a type
suitable for the required load in compliance
with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
Should the plug need to be replaced for any
reason, proceed as described below.
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow ..............................- Earth
Blue ....................................................- Neutral
Brown..................................................- Live
GREEN &YELLOW
E
The wire coloured
green and yellow must
be connected to the
L
N
terminal marked with
BROWN
the letter «E» or by the
BLUE
earth symbol
or
CORD CLAMP
coloured green and yellow.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Environmental concerns
Packaging materials
Ecological hints
The materials marked with the symbol
recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by
disposing of them properly in appropriate
collection containers.
are
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
●
Normally soiled laundry may be washed
without prewashing in order to save
detergent, water and time (the environment
is protected too!).
●
●
The machine works more economically if it is
fully loaded.
Old machine
Use authorised disposal sites for your old
appliance. Help to keep your country tidy!
With adequate pre-treatment, stains and
limited soiling can be removed; the laundry
can then be washed at a lower temperature.
Measure out detergent according to the
water hardness, the degree of soiling and
the quantity of laundry being washed.
The symbol
on the product or on its
●
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
132 962 510 - 01 - 28 2008 Subject to change without notice
|