WASHING MACHINE
FLA 802 W
INSTRUCTION BOOKLET
35.292.690/1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
For the User
For the Installer
Important Safety Information
Your New Washing Machine
Description of the Appliance
The Control Panel
Operating sequence
Washing 4,5 kg of white cotton at 90 °C
Load the laundry
Measure out the detergent
Measure out the fabric softener
Select the required programme
Start the machine
2
4
Installation Instructions
24
Technical Specifications
24
25
26
26
27
28
28
28
29
29
Unpacking
5
Positioning
Water inlet
Water drainage
Levelling
Special conditions
In the interest of the environment
Electrical connections
Permanent connection
6
7-10
7
7
7
7
7
8
8
At the end of the programme
Washing 2 kg of mixed fabrics at 50 °C
Load the laundry
Measure out the detergent
Measure out the fabric softener
Select the required option
Select the required programme
Start the machine
9
9
9
9
9
10
10
10
At the end of the programme
Washing Hints
11-13
12
Which detergent to use?....
And in which form?
13
How much detergent and fabric softener?
Using a water softening agent
13
13
Wash Care Symbols
Washing Programmes
14
15-16
Maintenance and Cleaning
17-18
17
Descaling
After each wash
External cleaning
17
17
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the filter
The dangers of freezing
Maintenance Wash
17
17
18
18
18
Something Not Working
Service & Spare Parts
Customer Care
19-20
20
20
Guarantee conditions
Zanussi Service Force Addresses
21
22-23
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
i
Hints and tips
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Your New Washing Machine
i
Your new washing machine, meets all modern needs for effective treatment of laundry with low
water, energy and detergent consumption.
I
Automatic cooling of the wash water to 60°C
before draining, with the 90°C programme. This
reduces thermal shock to fabrics, helping to prevent
any creasing.
In the interest of the
environment
I
Materials marked with the symbol
recyclable.
are
I
I
The special wool programme with its new delicate
wash system treats your woollens with extreme
gentleness.
I
I
Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
The anti-unbalance device ensures that the washing
machine remains stable when spinning.
When the appliance is to be scrapped, cut off the
power supply cable and make the door closing
device unusable to prevent young children from
being trapped inside.
Ecological hints
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
I
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
I
Adjust the quantity of detergent according to the
How do we help to protect the environment?
We use recycled paper!
hardness of your water supply, the amount of
laundry and the degree of soiling.
I
Select an “economy” programme for normally soiled
laundry and a “quick” programme for lightly soiled
laundry.
I
A programme without prewash is sufficient for
normally soiled laundry.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the Appliance
1 Detergent dispenser drawer
2 Programme guide
3 “Mains-on” light
4 “Options” buttons
5 Programme selector dial & ON/OFF switch
6 Door opening handle
7 Filter
8 Adjustable feet
Detergent dispenser drawer
Prewash
Main Wash
Fabric softener
AL035
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Control Panel
1 Detergent dispenser drawer
2 Programme Guide
5 Economy button
By depressing this button prior to selecting wash
programmes “B”, “C” and “H”, you will obtain a
reduction of the temperature from 90˚C to 60˚C and
from 60˚/50˚C to 40˚C. The duration of the programme
will not alter. This will ensure a substantial saving in
electricity consumption. Use Economy when washing
fabrics which are lightly soiled.
3 Mains-on light
This light illuminates when the appliance is operating.
6. Programme Selector
4 Rinse hold button
To select the required programme turn the control
clockwise until the marker on the top coincides with the
number of the required programme (reference mark on
the control panel). If you pass the required number
Press this button to make the machine stop with water in
the drum after the synthetic or delicate wash cycles.
This prevents any creasing which may take place if the
clothes are left damp in the drum. When it is convenient
for you to empty the machine, simply press this button
again so that the machine can proceed to drain and short
spin, or turn the dial to the drain programme “N”. If this
button is not activated, the washing programmes will
end with a short spin.
NEVER
TURN
THE
CONTROL
ANTICLOCKWISE just continue clockwise until the
required number is reached again.
Do not press this button for woollens: wool items
should be gently spun.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Sequence
Before your first wash, we recommend that you run a
cotton cycle at 60°C, without any laundry in the
machine, to remove any manufacturing residue from the
drum and tub.
Pour 1/2 a measure of detergent into the dispenser
drawer and start the machine.
WASHING 4.5 KG OF WHITE COTTON AT 90°C
Suppose you have 4.5 kg of heavily soiled laundry to
wash. It is white cotton and is suitable for high
temperature washing
1. Load the laundry
Open the door.
Place the laundry in the drum, one item at a time,
shaking out as much as possible. Close the door.
P0004
2. Measure out the detergent
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent recommended by
the manufacturer in a graduated cup and pour it into the
main wash compartment
.
If you wish to carry out a prewash(*), pour detergent
into the compartment marked
(*) Prewash is available in programme “A”.
AL025
3. Add the fabric softener
(if required)
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
«MAX» mark in the drawer).
Close the drawer gently
AL023
4. Select the required programme
Turn the programme selector dial CLOCKWISE to the
required programme.
AL038
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Start the machine
Before starting up the machine check that:
I
the appliance is plugged in
I
the water supply taps are turned on
I
the door and the detergent dispenser drawer are
closed.
Pull the programme selector dial outwards
The operating pilot light will illuminate and the machine
will start operating
6. At the end of the programme
The machine stops automatically and the mains-on light
goes out.
The door is controlled by a safety device which releases
3 minutes after the end of the programme.
Before opening the door ensure there is no water in
the drum.
Switch the machine off by pushing in the programme
selector dial.
When the programme has finished, you are advised to
unplug the appliance and turn off the water taps
Leave the door open to prevent the formation of mildew
and unpleasant smells.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHING 2 KG OF MIXED FABRICS AT 50 °C
Suppose you have 2 kg of MIXED FABRICS to wash.
They are rather delicate fabrics and should not be
washed at a high temperature.
1. Load the laundry
Open the door.
Place the laundry in the drum, one item at a time,
shaking out as much as possible. Close the door.
P0004
2. Measure out the detergent
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent recommended by
the manufacturer in a graduated cup and pour it into the
main wash compartment
.
AL025
3. Add the fabric softener
(if required)
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
«MAX» mark in the drawer).
Close the drawer gently.
AL023
4. Select the required option(S)
Depress Rinse Hold button
,if required
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select the required programme
Turn the programme selector dial CLOCKWISE to the
required programme
AL038
6. Start the machine
Before starting up the machine check that:
I
the appliance is plugged in
I
the water supply taps are turned on
I
the door and the detergent dispenser drawer are
closed.
Pull the programme selector dial outwards
The mains-on light will illuminate and the machine will
start operating
7. At the end of the programme
The machine stops automatically and the mains-on light
goes out.
If you have depressed the Rinse Hold button
, the
machine will stop with the water left in the tub, to
prevent the fabric from creasing. To drain the water
release the same button ( the clothes will be gently
spun) or select programme “N”
The door is controlled by a safety device which releases
3 minutes after the end of the programme.
Before opening the door ensure there is no water in
the drum.
Switch the machine off by pushing in the programme
selector dial.
When the programme has finished, you are advised to
unplug the appliance and turn off the water taps
Leave the door open to prevent the formation of mildew
and unpleasant smells.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Hints
i
I
Do NOT overload the machine. Weigh the laundry the
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special pre-
soak product or biological detergent.
first few times you use the appliance.
The average weights of the most common items are
listed below as a guide:
1000g = 1 kg
I
I
Only wool marked «Pure New Wool - washable,
preshrunk» can be washed in the machine using the
wool programme; other types of wool should be
washed by hand or dry cleaned.
Sheet
700-1000 g
100-200 g
400-500 g
50-100 g
Pillow case
Tablecloth
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
Serviette
Tea towel
70-120 g
Linen hand towel
Towelling hand towel
Towelling bath towel
Bath robe
100-150 g
150-250 g
700-1000 g
1000-1500 g
200-300 g
150-200 g
I
I
Once you have finished using the machine, you are
advised to unplug it and turn off the water taps.
To avoid an excessive and damaging amount of
lather when washing net curtains, it is advisable to
wash large curtains singularly and take extra care
when measuring the detergent.
Man’s shirt
Apron
Should an excess of lather accidentally occur, switch
off the machine, select the spin programme which is
preceded by a drain cycle, to remove the lather and
then start the wash again.
I
I
Load the laundry loosely alternating large items with
small ones.
I
I
I
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
Avoid washing unhemmed or torn items as they may
unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.
I
I
I
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
I
When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.
I
I
I
White items should not be washed with coloured
items.
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Use a good quality detergent suitable for automatic
washing machines.
I
I
Use the correct quantities of detergent.
For wool, use gentle detergent only in small
quantities.
I
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Delicate Items
Which detergent to use?....
To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
When washing delicates such as woollens, you should
use a product which is specially designed to care for
fine fabrics. Dreft Automatic is suitable for woollens
and other delicates.
To maintain the appearance of your clothes and
household textiles and to make them last longer you
should use different types of detergent for different
washes, whether for whites, colours or delicates.
Whites
We recommend the Ariel product range which is
biological and designed to provide excellent cleaning
and stain removal even at low temperatures.
Laundry Bleach
For additional stain removal you may wish to use a
product such as Ace Gentle Bleach which is used in
addition to your chosen detergent. Ace is suitable for all
washable fabrics including silks, woollens and
coloureds.
Non Biological
If you prefer to use a non biological detergent, which
does not contain enzymes we recommend Fairy. Fairy
provides good cleaning and stain removal.
Coloureds
For coloured items you should use a detergent which is
designed to clean while maintaining the original colour.
Ariel Color does not contain bleach and therefore helps
to preserve colours.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Bounce conditioning sheets for use in a tumble dryer.
We recommend the conditioning sheets are pinned
(using a safety pin) to an article of laundry and placed in
the tumble dryer.
And in which form?
Not only are there different types of detergent, but they
are also available in different forms. Whether you
choose a powder or liquid in traditional or compact form
is down to personal choice.
Traditional Powders
Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.
Traditional Liquids
Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol
, start
the machine immediately upon placing the detergent in
the dispenser drawer.
How much detergent and fabric
softener?
Alternatively the detergent is measured into the specially
designed dosing device* which should be placed on top
of the laundry, and at the back of the machine drum.
The amount to be used depends on:
the load:
Compact Powders and Liquids
if the detergent manufacturer does not make any
specification for small loads, use a third less for half
loads, and for very small loads only use half of the
amount of washing powder recommended for a full
load.
Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and
generally require a smaller dosage. Follow the
manufacturer’s instructions to ensure the most
economical usage. Pour the detergent directly into the
dispenser drawer, or alternatively measure the detergent
into the specially designed dosing device* which should
be placed on top of the laundry, and at the back of the
machine drum.
the degree of soiling of the washing:
for only lightly soiled washing use less washing
powder. Follow the instructions of the detergent
manufacturer.
the water hardness:
*If you use a dosing device in a washer dryer,
please ensure the dosing device/ball is removed
before carrying out a drying programme.
the harder the water, the higher the dosage!
Using a water softening agent
In hard water areas, the use of a water softening agent
can reduce the amount of detergent necessary. See
manufacturers recommendations.
Fabric Conditioners
These are ideal for improving “softness”, and also
reduce static cling on synthetics and make ironing easier.
They are available in two types:
For example Lenor liquid fabric softener, for use in the
washing machine/washer dryer. The liquid fabric
softener should be poured into the compartment marked
with the symbol
.
Follow the manufacturer’s dosage instructions and never
exceed the MAX level.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
FABRIC
White Cotton or Linen
without Special Finishes
Normal (Maximum)
95
Cotton, Linen or Viscose
without Special Finishes
Colour fast at 60°C.
Normal (Maximum)
60
50
Nylon, Polyester/Cotton, Viscose
Reduced (Medium)
Normal (Maximum)
Reduced (Medium)
with
Special
Finishes,
Cotton/Acrylic Mix.
Cotton, Linen or Viscose
Colour fast at 40°C but not 60°C.
40
40
40
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
Much Reduced (Minimum)
Hand wash only
Wool, wool mixtures, Silks
Do not machine wash
BLEACHING
Chlorine bleach may be used
IRONING
Cotton, Linen, Viscose
Polyester mixtures, Wool
Acrylic, Nylon, Polyester
Hot iron
Warm iron
Cool iron
DRY CLEANING
P
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
TUMBLE DRYING
May be tumble dried
with high heat setting
with low heat setting
A cross through any symbol means «DO NOT»
X
Important Notes
For best results, always use the dispenser drawer for dispensing detergents and liquid additives.Once the dispenser has
been filled, close it by pushing it in gently. This is particularly important if you are using fabric conditioner to avoid
the conditioner entering the machine prematurely.
When using liquid detergent and a prewash programme, place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Programmes
Programmes for cotton and linen
Degree of soil and type Programme dial
Wash programme
Possible Max.
Description
of laundry
position
options
load
White cotton, for
example heavy soiled
work garments, sheets,
Prewash at 40 ˚C
Wash at 90˚C
4 rinses
A
4.5 kg
Whites+Prewash
Whites
household
linen,
Long spin at 800 rpm
underwear, towels.
White cotton, for
example normally soiled
sheets and household
linen.
Wash at 90˚C
4 rinses
Long spin at 800 rpm
4.5 kg
4.5 kg
4.5 kg
B
White cotton economy,
for example lightly soiled
sheets and household
linen.
Wash at 60˚C
4 rinses
Whites+
B +
(*)
Long spin at 800 rpm
Economy
Coloured cotton or linen
fabric, shirts, underwear,
towels.
Wash at 60˚C
4 rinses
Long spin at 800 rpm
Fast coloureds
C
Coloured
economy, for example
delicate coloureds, men’s
shirts,
underwear.
garments
Wash at 40˚C
4 rinses
Long spin at 800 rpm
Fast coloureds +
Economy
4.5 kg
C +
blouses,
Non fast coloured cotton
or linen fabrics, shirts,
blouses, underwear.
Wash at 40˚C
4 rinses
Long spin at 800 rpm
Non Fast
4.5 kg
4.5 kg
D
F
Coloureds
Lightly soiled laundry
such as sport apparel,
sheets used once.
Wash at 40˚C
4 rinses
Long spin at 800 rpm
Quick wash
Separate spin for cotton
and linen items
Long spin at 800 rpm
4.5 kg
Spin 800 rpm
G
(*)This 60°C programme is the reference programme for the Energy label according to EEC Directive 92/75.
Water
Energy
Time
67 litres
1,2 kWh
125 minutes
Water filling:
Programmes
Programmes
Programmes
30˚-40˚C
50˚-60˚C
90˚C
cold water filling
hot and cold water filling
hot water filling
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Programmes
Programmes for synthetics, delicates and wool
Degree of soil and type Programme dial
Possible Max.
Wash programme
Description
of laundry
position
options
load
Synthetic or mixed
fabrics,
underwear,
Wash at 50˚C
3 rinses
Short spin at 600 rpm
H
coloured garments, non-
shrink shirts, blouses.
(Normally soiled)
2 kg
Mixed Fabrics
Synthetic or mixed
Wash at 40˚C
3 rinses
Short spin at 600 rpm
Mixed Fabrics
+Economy
fabrics,
underwear,
2 kg
1 kg
2 kg
H +
coloured garments, non-
shrink shirts. blouses.
Specially
programme for wool
garments
tested
Wash at 40˚C
3 rinses
Short spin at 600 rpm
Wool Care
Delicates
J
Wash at 40˚C
3 rinses
Short spin at 600 rpm
Delicate fabrics, for
example curtains.
K
This programme can be
used for rinsing hand
washed garments.
3 rinses (with fabric
softener if required).
Short spin at 600 rpm
Hand Rinses
Freshen Up
L
2 kg
1 rinse with fabric
softener and short
spin at 600 rpm
Laundry which needs
freshening up
M
2 kg
2 kg
Separate spin for
synthetics and delicates
Draining of water and
short spin at 600 rpm.
For emptying out the last
rinse water in programs
with Rinse Hold option
Draining of water
Drain
N
-
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Before any maintenance or cleaning is carried
out you must DISCONNECT the appliance
from the electricity supply
Descaling
The water we normally use contains lime. It is a good
idea to periodically run a high temperature wash with
detergent or use a descaler in the machine. Do this
separately from any laundry washing, and according to
the manufacturer's instructions. This will help to prevent
the formation of lime deposits.
After each wash
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
Maintenance Wash
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.
To run a maintenance wash:
* The drum should be empty of laundry.
* Select the hottest cotton wash programme.
* Use a normal measure of detergent, must be a powder
(such as Ariel Futur).
External cleaning
Clean the exterior cabinet of the appliance with soap
and water only, and then dry thoroughly.
Clean the control panel using a damp cloth only.
Do not use abrasives
Cleaning the dispenser drawer
From time to time the washing powder and additive
dispenser drawer should be cleaned.
Remove the drawer by pulling it out firnly. Flush it out
under a tap, to remove any traces of accumulated
powder.
AL033
AL021
Cleaning the drawer recess
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme for a
few minutes without any clothes in the drum.
P0185
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the filter
The water drain filter
A clean filter is important for the correct functioning of
the machine, and should therefore be cleaned after every
washing programme.
Open the filter door and place a container underneath to
catch any spillage. If the filter is blocked and the
machine is unable to drain you will need to drain the
water manually from the machine at this stage. To do
this, unhook the drain hose from the standpipe or sink
and hold the end of the hose over a bowl on the floor.
The water should drain by gravity into the bowl. When
the bowl is full, hook the hose back up and empty the
bowl. Repeat the procedure until water stops flowing
out.
AL015
AL012
Unscrew and remove the filter.
Clean carefully under a fast running tap.
Replace the filter turning now clockwise and tighten it.
P0040
AL017
Warning
When the appliance is in use and depending on the
programme selected there can be hot water in the filter.
Never remove the filter during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When replacing the filter, ensure it is securely
retightened so as to stop leaks and young children being
able to remove it.
The water inlet filters
If your water is very hard or contains traces of lime
deposit, the water inlet filters may become clogged.
It is therefore a good idea to clean it from time to time.
Turn off the water taps. Unscrew the water inlet hoses.
Remove and clean the filters using a hard bristle brush.
Replace the filters and tighten up the inlet hoses.
P0090
The dangers of freezing
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
I
Turn off the water taps.
I
Unscrew the inlet hoses.
I
Unhook the drain hose from the rear support and
position the end of this hose and that of the inlet
hose in a bowl. Run the draining programme.
I
Disconnect the appliance.
I
Screw the inlet hoses and reposition the drain hose.
I
When you intend to start the machine up again,
make sure that the room temperature is above 0°C.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your Zanussi Service Force Centre, please carry out the checks listed below.
Important:If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation
a charge will be made even if the appliance is in guarantee.
Symptom
Possible causes
I
The machine does not start
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no current at the socket
The main fuse has blown.
The selector dial is not correctly positioned and pulled out
No water is entering the machine (see: the machine does not fill)
I
I
I
I
I
I
The machine does not fill
Ensure the water taps are open and the water supply has not been
disconnected
The filter in the inlet hoses are blocked.
The inlet hoses may be squashed or kinked.
The water pressure is too low
I
I
I
I
The machine fills then empties
immediately
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
I
I
I
The machine does not empty and/or
does not spin
The drain hose may be squashed or kinked
The RINSE HOLD option has been selected.
The drain filter may be blocked
The drain hose extension is not correct. Follow the instructions for
I
I
I
connecting to the waste.
The drainage system pipes are blocked.
I
I
There is water on the floor
Too much detergent or unsuitable detergent has been used (creates too
much foam).
I
Check whether there are any leaks from one of the inlet hose fittings. It
is not always easy to see this as the water runs down the hose; check to
see if it is damp.
The drain hose may be damaged or not securely positioned.
The detergent dispenser drawer or recess is clogged.
The drainage system pipes are blocked.
I
I
I
I
Unsatisfactory washing results
The machine vibrates or is noisy
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
Stubborn stains have not been treated prior to washing
The correct temperature to suit the wash programme has not been
I
I
selected.
I
Too much laundry has been placed in the drum.
I
The internal packing has not been removed.
The machine is in contact with the wall or furniture.
The machine is not level.
The washing load is badly distributed in the drum.
There is very little laundry in the drum.
The machine is overloaded
I
I
I
I
I
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Possible causes
I
The door will not open
The programme is still running.
The door lock has not yet released
The water level in the drum is too high or the machine is heating.
I
I
I
Spinning starts late or the machine
does not spin
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen several
times before the load is evenly distributed and spinning can resume
eventually at a lower speed. If the wash load is still not sufficiently
distributed, after 10 minutes, the machine will not spin. In this case,
redistribute the load manually and reselect the spin programme.
I
The machine makes an unusual
noise
The noise produced when spinning may differ from your previous
washing machine, which is due to the modern drive system. This new
motor ensures a softer start and more even distribution of the laundry in
the drum when spinning, as well as increased stability of the machine.
I
No water is visible in the drum
Machines based on modern technology operate very economically
using very little water without affecting wash results.
Customer care
Service & Spare Parts
For general enquiries concerning your Zanussi appliance
or for further information on Zanussi products, please
contact our Customer Care Department by letter or
telephone at the address below or visit our website at
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Zanussi Service Force Centre by telephoning:-
0870 5 929929
Customer Care Department
Zanussi
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area. The
addresses are listed on the following pages. Before
calling out an engineer, please ensure you have read the
details under the heading “Something Not Working.”
55-77 High Street
Slough
Berkshire
When you contact the Service Force Centre you will
need to give the following details:
SL1 1DZ
Tel 08705 727727 *
1. Your name, address and post code
2. Your telephone number
* Calls to this number may be recorded for training
purposes
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date
Mod.
..........
Ser.
Mod. ..........
Prod. No. ...........
Ser. No. .........
P0042
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee Conditions
Zanussi standard guarantee
conditions
Exclusions
This guarantee does not cover:
I
Damage or calls resulting from transportation,
This guarantee is in addition to your statutory and other
legal rights.
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
We, Zanussi, undertake that if, within 12 months of the
date of the purchase, this ZANUSSI appliance or any
part thereof is proved to be defective by reason only of
faulty workmanship or materials, we will, at our option,
repair or replace the same FREE OF ANY CHARGE
for labour, materials or carriage on condition that:
I
I
I
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
I
The appliance has been installed correctly and used
only on the electricity supply stated on the rating
plate.
Products of Zanussi manufacture which are NOT
marketed by Zanussi.
I
The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s operating and maintenance
instructions.
Zanussi European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new home
subject to the following qualifications:
I
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
I
The guarantee starts from the date you first
I
All service work under this guarantee must be
undertaken by a Zanussi service representative or
authorised agent
purchased your product
I
The guarantee is for the same period and to the same
extent for labour and parts as exists in the new
country of use for this brand or range of products
Any appliance or defective part replaced shall become
our property.
I
This guarantee relates to you and cannot be
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours in which case a charge will be made.
transferred to another user
I
Your new home is within the European Community
(EC) or European Free Trade Area
I
The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
Before you move please contact your nearest
Customer Care Centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your move
and able to look after you and your appliances.
France
Senlis
+33 (0)3 44 62 29 99
+49 (0)911 323 2600
+39 (0) 1678 47053
+46 (0)8 738 79 50
+44 (0)1753 219 897
Germany Nurnberg
Italy
Pordenone
Stockholm
Slough
Sweden
UK
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To contact your local Zanussi Service Force Centre telephone
08705 929 929
ISLE OF LEWIS
ND Macleod
16 James Street
Stornoway
CHANNEL ISLANDS
NORTH EAST
GUERNSEY
JERSEY
Guernsey Electricity
PO Box 4
Isle of Lewis PA87 2QW
GATESHEAD
Unit 356a
Dukesway Court
Dukesway
Vale, Guernsey
Channel Islands GY1 3AD
KELSO
2, 6 & 8 Woodmarket
Kelso
Borders
Gateshead NE11 0BH
Jersey Electricity Company
Haut De L’orme
Rue De Haut De L’orme
Trinity
Jersey
Channel Islands JE3 5FG
GRIMSBY
HULL
15 Hainton Avenue
Grimsby
N. E. Lincs
TD5 7AX
DN32 9AS
ORKNEY
PERTH
7 King Street
Kirkwall
Orkney
Unit 1
Boulevard Industrial Estate
Hull
HU3 4AY
KW15 1JF
SCOTLAND
Scottish Hydro Electric
Central Warehouse
Inveralmond
ABERDEEN
54 Claremont Street
Aberdeen AB10 6RA
LEEDS
64-66 Cross Gates Road
Cross Gates
Leeds
(OWN SALES)
SHETLAND
Perth PH1 3AF
AUCHTERMUCHTY 33a Burnside
Auchtermuchty
LS15 7YS
3-4 Carlton Place
Lerwick
Shetland
Fife KY14 7AJ
NEWTON AYCLIFFE Unit 23
Northfield Way
(OWN SALES)
SHETLAND
ZE1 0PW
BLANTYRE
Unit 5
Block 2
Auchenraith Ind. Estate
Rosendale Way
Blantyre G72 0NJ
Aycliffe Industrial Park
Newton Aycliffe
DL5 6EJ
Bolts Shetland
26 North Road
Lerwick
SHEFFIELD
Pennine House
Roman Ridge Road
Sheffield
(OWN SALES)
WHALSAY
Shetland ZE1 0PE
DUMFRIES
DUNOON
93 Irish Street
Dumfries
DG1 2 PQ
Leask Electrical
Harisdale
Symbister, Whalsay
S9 1GB
(OWN SALES)
Shetland ZE2 9AA
7 Hill Street
Dunoon
NORTH WEST
Argyll
PA23 7AL
BIRKENHEAD
CARLISLE
1 Kelvin Park
Dock Road
Birkenhead
CH41 1LT
NORTHERN IRELAND
EDINBURGH
Unit 12
BELFAST
Owenmore House
Kilwee Business Park
Dunmurry
Belfast
BT17 0HD
Dumbryden Ind. Estate
2 Dumbryden Road
Edinburgh
Unit 7
James Street Workshops
James Street
Carlisle
EH14 2AB
Cumbria
CA2 5AH
GLASGOW
Unit 4
WALES
Wellington Road
Bishopriggs
Glasgow G64 2SA
ISLE OF MAN
BOLTON
South Quay Ind. Estate
Douglas
Isle of Man
CARDIFF
CLYWD
DYFED
Unit 4
Guardian Industrial Estate
Clydesmuir Road
Cardiff
IM1 5AT
INVERNESS
Unit 3BI
Smithton Ind. Estate
Smithton
Inverness IV2 7WL
Unit B
CF2 2QS
Central Industrial Estate
St Marks Street
Bolton
Unit 6-7 Coed Parc
Abergele Road
Rhuddlan
Clwyd
LL18 5UG
ISLE OF ARRAN
ISLE OF BARRA
ISLES OF BUTE
R Haggerty
Bruach
Blackwaterfoot
BL3 6NR
PRESTON
Unit 250
Isle of Arran
Dawson Place
Bamber Bridge
Preston
Unit 9
J Zerfah
244 Bruernish
Isle of Barra
St. Clears Business Park
Tenby Road
St. Clears
Carmarthen
SA33 4JW
Lancashire PR5 8AL
Western Islands HS9 5QY
STOCKPORT
Unit 20 Haigh Park
Haigh Avenue
Stockport
Walker Engineering
Glenmhor
SK4 1QR
Upper Serpentine Road
Rothesay
Isle of Bute PA20 9EH
OSWESTRY
Plas Ffynnon Warehouse
Middleton Road
Oswestry
SY11 2PP
22
Download from Www.Somanuals.com. All Manuals Search And Download.
08705 929 929
To contact your local Zanussi Service Force Centre telephone
LONDON & EAST ANGLIA
MIDLANDS
SOUTH EAST
BECKENHAM
11a Gardner Ind. Estate
Kent House Lane
Beckenham
BIRMINGHAM
66 Birch Road East
Wyrley Trading Estate
Witton
ASHFORD
Unit 2
Bridge Road Business Cent
Bridge Road
Kent BR3 1QZ
Birmingham
B6 7DB
Ashford
Kent TN23 1BB
CHELMSFORD
COLINDALE
Hanbury Road
Widford Ind. Estate
Chelmsford
Essex
BOURNE
Pinfold Road
Bourne
PE10 9HT
FLEET
Unit 1
Redfields Ind. Estate
Church Crookham
Fleet
CM12 3AE
BRIDGNORTH
68 St. Mary’s Street
Bridgnorth
Unit 14
Hampshire GU13 0RD
Capitol Park
Capitol Way
Colindale
Shropshire
WV16 4DR
HAYWARDS
HEATH
21-25 Bridge Road
Haywards Heath
Sussex RH16 1UA
London NW9 0EQ
GLOUCESTER
HEREFORD
101 Rycroft Street
Gloucester
GL1 4NB
ELTHAM
194 Court Road
Mottingham
Eltham
London SE9 4EW
Units 3 & 4
Bank Buildings
Cattle market
Hareford
TONBRIDGE
Unit 30
Deacon Trading Estate
Morley Road
Tonbridge
ENFIELD
284 Alma Road
Enfield
London
HE4 9HX
TN9 1RA
EN3 7BB
HIGHAM FERRERS 30 High Street
Higham Ferrers
GRAVESEND
Unit B4
Northants
SOUTH WEST
Imperial Business Estate
West Mill
Gravesend
Kent
NN10 8PL
BARNSTAPLE
Main Road
Fremington
Barnstaple
North Devon EX31 2NT
ILKESTON
Unit 2
Furnace Road
Ilkeston DE7 5EP
DA11 0DL
IPSWICH
Unit 6C
LEICESTER
Unit 7
Elton Park Business Centre
Hadleigh Road
Ipswich
Oaks Industrial Estate
Coventry Road
Narborough
Leicestershire
LE9 5GF
BOURNEMOUTH 63-65 Curzon Road
Bournemouth
Dorset
BH1 4PW
IP2 0DD
LETCHWORTH
LONDON
16-17 Woodside Ind. Park
Works Road
Letchworth
Herts
SG6 1LA
BRIDGEWATER
BRISTOL
6 Herswell Business Park
Salmon Parade
Bridgwater
LINCOLN
Unit 8
Clifton Street
Stone Field Park
Lincoln
Somerset TA6 5PY
LN5 8LQ
11 Eldon Way
Eldonwall Trading Estate
Bristol
2 - 4 Royal Lane
Yiewsley
West Drayton
Middlesex
NEWCASTLE
UNDER LYME
18-21 Croft Road
Brampton Ind. Estate
Newcastle under Lyme
Staffordshire
BS4 3QQ
UB7 8DL
EMSWORTH
ISLE OF WIGHT
266 Main Road
Southbourne
Emsworth
ST5 0TW
MAIDENHEAD
MOLESEY
Reform Road
Maidenhead
Berkshire
PO10 8JL
REDDITCH
13 Thornhill Road
North Moons Moat
Redditch
Worcestershire
B98 9ND
SL6 8BY
Unit 8
Enterprise Court
Ryde Business Park
Ryde
10 Island Farm Avenue
West Molesey
Surrey
Isle of Wight PO33 1DB
KT8 2UZ
TAMWORTH
Unit 3
Sterling Park
Claymore
Tamworth
B77 5DQ
NEWTON ABBOT Unit 2
Zealley Ind. Estate
NEWBURY
9 Pipers Court
Berkshire Drive
Thatcham
Berkshire
RG19 4ER
Kingsteignton
Newton Abbot
TQ12 3TD
WORCESTER
Units 1 & 2
Northbrooks Close
Gregorys Mill Ind. Estate
Worcester
REDRUTH
Unit 7D
NORWICH
SUNBURY
2b Trafalgar Street
Norwich
NR1 3HN
Pool Ind. Estate
Druids Road
Redruth
WR3 8BP
Cornwall TR15 3RH
Unit 1a
The Summit
Hanworth Road
Sunbury on Thames
TW16 5DB
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Technical Specifications
DIMENSIONS
Height
Width
Depth
85 cm (33.5”)
60 cm (23.6”)
55 cm (22.7”)
POWER SUPPLY VOLTAGE
MAX. POWER ABSORBED
230-240 V/50 Hz
2600 W (13A)
WATER PRESSURE
Minimum (cold)
Minimum (hot)
Maximum
50 kPa (7 psi)
30 kPa (4 psi)
800 kPa (110 psi)
MAXIMUM RECOMMENDED LOAD
Cotton, linen
Synthetics
Delicate fabrics
Wool
4.5 kg (10 lbs)
2 kg (4.5 lbs)
2 kg (4.5 lbs)
1 kg (2.2 lbs)
SPIN SPEED
Maximum
800 rpm
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
All transit bolts and packing must be removed
before using the appliance
You are advised to keep all the packaging for re-use in
case the appliance has to be transported again.
I
Unscrew and remove the three rear transit bolts
(using a spanner).
P0287
I
Lay the machine gently on its back, making sure
that the hoses are not squashed.
We suggest a polystyrene angle bracket from the
packing is placed on the floor before tilting it back
to avoid the hoses being squashed.
P0018
I
Carefully remove the polyethylene bags located at
the base of the machine by pulling them toward the
centre of the machine.
1
2
AL009
I
Place the machine in an upright position and
remove the three plastic spacers.
P0001
I
Plug the 3 holes with the plastic plugs which you
can find in the envelope containing the instruction
booklet.
P0002
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning
Your new Zanussi washing machine has been designed
to be permanently plumbed in to your home’s water
supply and drainage system. However, if this is not
possible, it may be connected to suitable existing taps,
with the drain hose discharging into the sink.
The appliance has two inlet hoses, hot and cold, with
female 3/4” BSP thread connectors. If this connection
is not compatible with the plumbing of the existing
installation, a variety of connectors are available from
good hardware stores and plumbers merchants to suit
most domestic plumbing. Any alterations to your
existing plumbing must be carried out by a competent
person, or qualified plumber.
COLD WATER SUPPLY
HOT WATER SUPPLY
Water inlet
The inlets on the back of the appliance are colour coded,
blue for cold and red for hot.
Before connecting the hoses, be sure to fit the black
washers supplied (A) as per diagram.
If only a cold water supply is available, connect the two
hoses to a cold water outlet by means of a ‘Y’
connection piece.
Installation should comply with local water authority
and building regulation requirements.
The appliance must be given a separate cold water
supply and not be connected to a mixer tap, a single
outlet water heater or a booster pump. A minimum
water pressure of 7psi is required for safe operation of
the appliance.
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
A
There should be a minimum distance of 5.02m (16
1/2ft) between the appliance’s inlet and the bottom of
the tank.
AL013
There will be sufficient pressure for the hot water
supply from the hot water cylinder if the height between
the appliance’s inlet and the bottom of the cold water
storage cistern (not between the appliance and the hot
water cylinder) is at least 2.74m (9ft).
Set the hoses correctly by loosening the ring nuts. After
positioning the inlet hoses, be sure to tighten the ring
nuts again to prevent leaks.
P0021
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Water drainage
This appliance is designed to be permanently plumbed
into your home's water supply and drainage system.
3 pin
The appliance drain hose should hook (use the plastic
“U-piece” supplied) into a standpipe with an internal
diameter of approximately 38mm (see diagram) thus
ensuring there is an air break between the drain hose
and standpipe.
P1039
When discharging into a standpipe ensure that the top of
the curve in the hose end is no more than 90cm (35.4'')
and no less than 60cm (23.6'') above floor level. The
upright standpipe should have a minimum length of
30cm (12'') from the bottom of the elbow to the top of
the pipe (see diagram).
1
38 mm.(1/2") diameter
standpipe
P1040
Make sure that it is designed in such a way, that the end
of the drain hose cannot be covered with water.
The drain hose may be extended to a maximum of 3
metres. An additional drain hose and joining piece is
available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
If you intend the drain hose to empty into a sink, make
sure that the sink is empty and the plug hole is not
blocked. Use the plastic “U-piece” supplied.
P0022
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Levelling
Level the washing machine by loosening or tightening
the feet. Once in the right position fix the feet by
pushing the nuts against the base of the case
Accurate levelling prevents vibration, noise and
displacement of the machine during operation. After
levelling the machine, secure the feet by tightening the
ring nuts with the aid of a screwdriver.
Some vibration is inevitable, especially if mounted on a
wooden floor.
P0254
P0509
Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
Special conditions
If the floor is carpeted with a deep-pile carpet or
covered with crumbly or soft material, insert a rigid
support base under the feet to prevent noise, vibration or
displacement. The base should protrude a few
centimetres beyond the edges of the machine.
Warning
The machine should NOT be placed on deep pile
carpeting.
Note
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
In the interest of the
environment
Washing machines and dishwashers should be
connected to the FOUL drainage system, the water will
then be taken to a sewage works for treatment before
being discharged safely into a river.
SHOWER
It is essential that these appliances are not connected to
the surface water drainage system as this water is
discharged directly into a river or stream and may cause
pollution.
SINK TOILET
BATH
BIDET
If you require any further advice please contact your
local authority drainage department.
WASHING
MACHINE
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
UNTREATED
DISCHARGE
TREATED
DISCHARGE
RIVER
RIVER
P0987
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connections
Any electrical work required to install this appliance
should be carried out by a qualified electrician.or
competent person
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliace
rating plate (the plate is sticked to the rear of the
appliance).
The appliance is supplied with a 13 amp plug fitted. In
the event of having to change the fuse in the plug
supplied, use a 13 Amp BS1362 fuse. Only ASTA or
BSI approved fuses must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:
GREEN & YELLOW
E
Green and Yellow
Blue
- Earth
- Neutral
- Live
L
N
Brown
Connect the green and yellow (earth) wire to the
terminal in the plug which is marked with the letter «E»
BROWN
BLUE
CORD CLAMP
or the earth symbol
or coloured green and yellow.
P1041
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the plug
which is marked with the letter «L» or coloured red.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured insert
at the base of the plug.
A replacement cover/carrier must be obtained from your
local Zanussi Service Centre, whose address is listed in
this instruction manual.
Permanent connection
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3 mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.
WARNING: a cut off plug inserted into a 13
amp socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
The switch must not break the yellow and green earth
cable at any point.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
The Electrolux Group is the worldÑs largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. 14 billion USD
in more than 150 countries around the world.
Electrolux Household Appliances Limited 2001/10
Download from Www.Somanuals.com. All Manuals Search And Download.
|