INSTRUCCIONES – MANUAL DE INSTRUÇÕES
INSTRUCTIONS
LAVADORAS AUTOMATICAS
MÁQUINAS DE LAVAR
A ROUPA
WASHING MACHINES
FLS 432 C
FLS 522 C
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS
THESE WARNINGS ARE PROVIDED IN THE INTEREST
OF SAFETY. YOU MUST READ THEM CAREFULLY
BEFORE INSTALLING OR USING THE APPLIANCE.
■ Avoid washing frayed or torn articles and treat stains
such as paint, ink, rust, and grease before washing.
■ Garments which have been in contact with volatile
petroleum products should not be machine washed. If
volatile cleaning fluids are used, care should be taken to
ensure that the garement is dry before placing in the
washing machine.
It is most important that this instruction book should always
be at hand for the user for reference. Should the appliance
be sold or transferred to another owner, or should you
move house and leave the appliance, always ensure that
the book is left with the appliance in order that the new
owner can get to know the functioning of the appliance and
the relevant warnings.
■ Wash small items such as socks, laces, washable belts ,
etc. in a washing bag or pillow case as it is possible for
such items to slip down between the tub and the inner
drum.
CHECK THE APPLIANCE UPON RECEPTION AND
SHOULD ANY DAMAGE BE OBSERVED CALL YOUR
DISTRIBUTER BEFORE YOU MAKE IT WORK.
■ Only wash the advised quantity of delicate fabrics.
Damage to the fabric can ensue if you over-fill. Refer to
the manufacturerÕs recommendations of quantities.
■ Children must not be allowed to temper with the controls
or play with the product.
■ Do not overload the appliance, see the relevant
WASHING PROGRAM section .
■ The appliance is heavy. Care should be taken when
moving it. Do NOT hold yourself on the controls.
■ Pets have been known to climb into washing machines.
Please check your drum before use.
■ All packing and transit bolts must be removed before
use.
■ The glass door becomes very hot during the wash cycle.
Keep children away from the appliance whilst it is in
operation.
■ Serious damage can occur to the product and to
property if this has not been adhered to. See relevant
section (unpacking) in the instruction booklet.
■ Before opening the door look through the ÒwindowÓ to
check if the water has been drained. Should there be
water do not open before draining. If in doubt read
section ÒINSTRUCTIONS FOR USEÓ.
■ The washing machine must be unplugged when
removing the interior transit bolts. Do not plug the
appliance before finishing the removal of the transit bolts
and the fixing of the caps in the holes where the security
bolts were.
■ Always unplug the appliance and turn off the water after
use.
■ If the appliance is to stand on a carpeted floor make
sure that there is space between the carpet and the
supporting feet of the appliance for the air to circulate
freely around .
■ Leave the porthole slightly ajar between washes to
preserve the door seal.
■ Unplug the appliance before cleaning.
■ Any electrical and/or plumbing work required to install
this appliance should be carried out by a qualified
electrician and/or plumber or competent person.
■ This product must be serviced by an authorised Service
Centre, and only genuine spare parts should be used.
Do not try to repair the appliance yourself.
■ It is dangerous to alter the the specifications or attempt
to modify this product in any way.
■ Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning of the machine. Contact
your local Service Centre. Always insist on genuine
spare parts.
■ Care must be taken to ensure that the appliance dos not
stand on the electrical supply cable.
■ Only wash fabrics which are designed to be machine
washed. If in doubt, consult the manufacturer of that
item.
■ Before washing ensure that all pockets are empty and
buttons and zips are fastened.
■ Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
appliance nor left in the pockets.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING AND INSTALLATION
TRANSIT SECURITY BARS
HYDRAULIC CONNECTION
Before starting the machine up, the transport security
bars must be removed as follows:
You are advised to keep all the transport security bars in
There should be a COLD WATER tap near the washing
machine with a screwing on connection pipe of 3/4 gas for
the water supply, a sink, a wash basin or a drainage system
in the wall.
case the appliance has to be transported again.
1. Unscrew and remove the
three rear screws by
means of a key.
Previously check if:
Ñ
Ñ
it is not a hot water tap.
the running water is clean. If not, run off a
reasonable amount of water to flush out any debris
that may have collected in the pipes.
Have the permanent drainage system in the wall checked
by a plumber.
Place the enclosed rubber joint, delivered in a plastic bag
together with the appliance (A) Fig.6), at the very end of the
inlet hose and carefully screw the pipe to the tap taking
care not to damage the screwdrive and fix the nut well on to
the end in order to avoid leaking.
2. Lean the appliance back
on the rear and fit one of
the polystyrene angles
between the appliance
and the floor.
If necessary turn the hose
adequately by unscrewing
the nut at the rear of the
appliance.
Make sure the hoses
are not squashed.
3. Carefully remove the
plastic bags on the right
and the left, pulling them
to the centre of the
appliance.
Now tighten the nut anew to avoid leaks. (Open the tap and
asure that it does not leak and close it again.)
Place the discharging hose
in a washbasin or sink with
the aid of the bent piece
delivered separately. The
bent piece has to be
entered into the tubeÕs
mouth in order to assure
the support. Aforesaid
piece allows the hose to be
fixed to the wall by means
of an opening on the upper
part and that way the hose
does not move and its
falling is avoided.
4. Place the machine in an
upright position and
remove the three plastic
bolts.
5. Plug the 3 holes with the
plastic plugs which you
can find in the envelope
containing the instruction
booklet.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
1,5 m. Maximum
IMPORTANT: The distance from the floor to the highest
part of the hose should be between 60 to 90 cm. (It is
advised to be between 60 and 70 cm). The hose must not
be bent nor twisted to avoid clogging. Should a prolongation
of the discharging hose be unavoidable this must never
surpass 1.5 m and must be of the same diameter as the
original hose.
ELECTRICAL CONNECTIONS
Before plugging the appliance make sure that:
1º the mains of your installation is the same as on the
rating plate of your appliance (the plate is sticked to the
rear of the appliance).
2º The meter, the fuses, the wiring and the socket outlet
can support the max. power absorbed stated on the rating
plate.
Make sure the hoses are not too tense.
LEVELLING
3º The socket base and the plug must fit in adequately
without any reducing interposition, multiple outlets or
adapters. If necessary replace the socket outlet by an
adequate one.
Level the appliance by loosening or tightening the feet.
Once in the right position fix the feet by pushing the nuts
against the base of the case. Accurate levelling will prevent
vibration, noise and displacement of the appliance during
operation.
The applicable rules for electrical security require an
adequate earthing. The plug of the appliance is
provided with such a device.
Some vibration is inevitable, especially if placed on a
wooden floor. Wooden floors are particularly susceptible to
vibrations. For advice, consult a builder. If posible always
place the appliance on a solid floor.
Make sure your socket outlet is provided with an
adquate earthing too.
The manufacturer declines any liability in case of
accidents or incicents should these safety measures
not be observed.
(Never touch the washing machine or any electric appliance
while standing on a wet floor or being barefoot.)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF THE CONTROLS
Control panel
1
2
3
4
5
6
1. WASHING POWDER DISPENSER
4. “NO SPINNING” BUTTON
The dispenser is
provided with 4
compartments marked
Pressing this button before starting the intense washing
program all spinnings will be excluded. The other steps of
the program remain unchanged.
with the following
symbols:
5. TEMPERATURE SELECTOR
This control allows you to select the temperature of the
washing cycle in accordance with the kind of clothes to be
washed.
Turn the control until the required temperature coincides
with the marker.
On the program table you will find the most apropriate
temperature for each kind of washing. Selecting ✳ any
program can be run through with cold water. This will
ensure a saving in electricity consumption.
ÇPrewashÈ symbol shows the compartment for the
prewash detergent.
ÇWashÈ symbol shows the compartment for the
washing detergent.
6. PROGRAM SELECTOR
ÇsmoothÈ symbol shows the compartment for the
smoothing additives.
To select the required program turn the control clockwise
until the marker on the top coincides with the number of the
required program (reference mark on the control panel). If
at any chance you pass by the required number NEVER
TURN THE CONTROL ANTICLOCKWISE just continue
clockwise until the required number is reached again.
ÇbleachÈ symbol shows the compartment for the
bleaching additives.
2. ON/OFF LAMP
It lights when the appliance is operating.
3. 1/2 LOAD BUTTON
Pressing this button before starting the intense program
there will be one rinse less which leads to energy and water
saving.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE CONTROLS DETERGENT AND ADDITIVES
1. LOADING THE WASHING MACHINE
4. SELECT THE TEMPERATURE
Load the laundry loosely, alternating large items with small
ones.
Turn the dial clockwise to the desired temperature .
Do not overload the washing machine, but always try to use
its utmost capacity in accordance with the type of fabric.
Reduce the quantity when washing very dirty or fluffy
laundry .
5. SELECT THE PROGRAM
Turn the dial clockwise until the marker reaches the desired
program.
Once the machine is working and you wish to add any item
you must stop the program.
6. START
IMPORTANT REMARK: This appliance is provided with a
security device to avoid opening during the cycles. Open it
only when absolutely necessary and wait 2 to 3 minutes
after you have stopped the machine to give the safety
device time to unlock.
Before pressing the On/off Button check if:
The door is properly closed.
The appliance is plugged in.
The water supply tap is turned on.
The drain filter is tight.
2. DOSE THE WASHING POWDER
The drain hose is adequately positioned.
Pull the program dial up to you till it klicks.
The pilot light comes on and the program will begin.
Pull the handle to open the
dispenser. Enter the
advised quantity of washing
powder into
compartment
7. STOP
The washing machine stops automatically once the cycle is
finished, the pilot goes out. Open the door 2 to 3 minutes
after the end of the program to give the safety device
time to unlock.
For prewash use
compartment
Close the tap and unplug the appliance. Leave the door
ajar for a few minutes for the steam to get out.
3. DOSE THE ADDITIVES
If you wish to use additives
enter the softener in the
compartmente with the
symbol and the
bleacher in the
compartment with the
symbol Never exceed
the MAX level.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMS FOR COTTON AND LINEN
Recommended load: max. 4,5 kg.
DEGREE
OF SOIL
COMPARTMENTS
TO USE
MAXIMUN
WATER TEMP.
POSITION
PROGRAM
PROGRAM
DESCRIPTION
Prewash
Wash at 90¡C
4 rinses
Spin 5 min.
WHITES
with prewash
heavy
soil
90
1
Wash at 90¡C
4 rinses
Spin 5 min.
WHITES
without prewash
normal
soil
90
60
40
2
2(•)
3
Wash at 60¡C
4 rinses
Spin 5 min.
FAST
COLOURS
normal
soil
Wash at 40¡C
4 rinses
Spin 5 min.
NON-FAST
COLOURS
normal
soil
Load bleacher
4 rinses
Spin 5 min.
RINSES
4
load additif
1 rinse
Spin 5 min.
ADDITIVES
SOFTENER
5
6
Drain water
Spin 2.5 min.
SPIN
( ) This 60¡ programme is the reference programme for the Energy label according to the article 2, paragraph 1 of the EEC
¥
Directive 92/75.
PROGRAMS FOR SYNTHETICS, MIXED AND WOOL
Recommended load: max. 2 kg (wool max. 1 kg.)
DEGREE
OF SOIL
COMPARTMENTS
TO USE
MAXIMUN
WATER TEMP.
POSITION
PROGRAM
PROGRAM
DESCRIPTION
Prewash at 30¡C
Wash at 60¡C
3 rinses
MIXED
FABRICS
heavy
soil
60
7
Stop with water in the drum
Wash at 60¡C
3 rinses
Stop with water in the drum
FAST
COLOURS
normal
soil
60
40
40
8
9
Wash at 40¡C
3 rinses
Stop with water in the drum
SYNTHETICS
DELICATES
normal
soil
Wash at 40¡C
3 rinses
Stop with water in the drum
WOOL
SILK
normal
soil
10
11
12
3 rinses
Stop with water in the drum
RINSES
DELICATES
Load additif
1 rinse
Stop with water in the drum
ADDITIVES
SOFTENER
Drain water
drum stands
still
DRAIN
13
For draining the water, once the cycle is finished, situate the timer Ò13Ó right in its place.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHING HINTS
Sort the laundry according to the type of fabric, colour
fastness and how dirty it is.
LOAD THE WASHING MACHINE
Check the quantity you are going to wash for each cycle.
When washing curtains remove the hooks.
It is rather difficult to weigh all the pieces to be washed. We
therefore advise you:
It is essential to wash new coloured items separately when
washing them for the first time.
Cotton and linen: fill the drum without pressing.
Synthetic resistant : fill two thirds of the drum.
Delicates and wool: fill half the drum.
When washing fabrics requiring different wash
temperatures together , always select the lowest one.
White items should NOT be washed with coloured ones.
For wool use gentle detergents only in small quantities.
Only wool marked ÔPURE NEW WOOL WASHABLE
PRESHRUNKÕ can be washed in the machine using the
wool program; other types of wool should be washed by
hand or dry cleaned.
TEMPERATURES
You are advised to wash whites at a temperature of 60¡C. If
the laundry is not very soiled this will be enough and it is
energy saving. If you want to wash whites without
temperature, you must choose the program 2.
Some stains such as fruit, wine, grass, rust, blood, etc. are
difficult to remove and should be treated before washing
with specific products which can be found in most
household shops. In any case they should be treated
immediately , later on they are difficult to remove.
Coloured fabrics are advised to be washed at 40¡C
although they would stand 60¡C.
When washing together dark and light colours the
temperature should not exceed 40¡C. Synthetic white and
light coloured fabrics can be washed at 60¡C, but here also
40¡ will do if they are not very soiled.
Damp laundry should be hung out to dry as soon as
possible after finishing the wash.
Knitwear and woollens should be dried flat, away from
direct sunlight.
Dark synthetics, delicate fabrics and wool must be washed
at a temperature lower than 40¡C. If one of the labels is
marked 30¡C, select 30¡C for the whole cycle.
On the care labels in most clothes wash code symbols can
be found which help you to select the adequate wash
program. You are advised to observe and follow these
instructions.
On the following table you will find the meaning of the
symbols.
TABLE OF SYMBOLS
The symbols on the labels are of great help for the wash, care and treatment.
STRONG WASH
Max. wash
temp. 95¡C
Max. wash
temp. 60¡C
Max. wash
temp. 40¡C
Max. wash
temp. 30¡C
Do not wash
at all
Hand wash
DELICATE WASH
BLEACHING
IRONING
Bleach in cold water
Do not bleach
Hot iron max. 200¡C
Hot iron max. 150¡C
Hot iron max. 100¡C
Do not iron
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 y R 113
Dry cleaning in
petrol, pure alcohol,
R 111 y R 113
Do not
dry cleaning
Dry cleaning
in all solvents
DRY
CLEANING
High
temperature
Low
temperature
DRYING
Flat
On the line
On clothes
hanger
Do not
tumble dry
Tumble dry
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND CLEANING
Before any maintenance or cleaning is carried out you
must DISCONNECT the appliance from the electricity
supply.
THE DANGERS OF FREEZING
If the machine is exposed to temperatures below 0¼C,
certain precautions should be taken.
* Turn off the water tap and unscrew the inlet hose.
* Select a wash program and run for a few seconds.
* Position the end of the drain hose in a bowl on the floor.
* Run the draining program for a few seconds.
EXTERNAL CLEANING
Clean the exterior cabinet of the appliance with neutral
soap and water only, and then try thoroughly.
This way you make sure now water at all remains in the
appliance which could freeze and thus damage it and its
surroundings.
CLEANING THE DISPENSER DRAWER
AND THE RECESS
When you need to start the machine up again, make sure
that the room temperature is above 0¡C.
Pull the drawer to remove (slightly at first till the stop, then
pull hard).
Flush well under a fast running tab.
Clean the recess with a small brush.
Replace the drawer.
CLEANING THE DRAIN FILTER
A clean filter is important for
correct functioning of the
washing machine, and it
should therefore be cleaned
regularly. Small objects left
in the pockets and yarn ist
retained here.
Unscrew the filter
completely turning it
anticlockwise.
P0341
Remove the filter and clean
it under a fast running tap.
Replace the filter turning now clockwise and tighten it.
CLEANING THE WATER INLET HOSE
FILTER
If it takes longer to fill up
the washing machine it is
time to check the water inlet
hose filter it may be
clogged. Turn off the water
tap. Unscrew the fixing nut
of the inlet hose. Remove
the filter from the
electrovalve and clean it
with a hard bristle brush
and replace it. Screw on the
nut thoroughfully.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING
Before contacting your local Service Force Centre, check
your machine against the simple maintenance guidelines
given below.
THE MACHINE LEAKS OR OVERFLOWS
* Too much washing powder.
* Unsuitable washing powder.
* Check the joints for leaks. It is rather difficult to see the
water running along a hose.
The appliance does not start up
* Check if the door is closed properly.
* Check if the appliance is plugged in.
* Check the fuse.
THE MACHINE VIBRATES OR IS NOISY
* Check if all transport devices have been removed.
* Check if the appliance touches the walls or furniture.
* Check if the program dial is in the correct position.
* Check if the legs are adequately levelled and the nuts
tight
THE MACHINE DOES NOT FILL
* Check if the water tap is on.
* Check if the tap is clogged.
* Check if the inlet hose is bent.
* Check if the water inlet filter is clogged.
THE MACHINE EMPTIES AS IT FILLS
* The end of the drain hose is too low (see page. 25)
THE MACHINE DOES NOT DRAIN OR SPIN
* Check if the drain hose is bent or squashed.
* Check if the drain filter is clogged.
* Check if the selected program includes spinning.
* Check if the ÔRinse HoldÕ botten is pressed.
If, after above checks, there is still a fault, call your Local Service Centre. Please make sure you give the model and serial
number of the appliance and the purchasing date.
IMPORTANT REMARK: This washing machine is provided with the latest technical advances in washing and water level
reduction. It is quite right that you do not see the water through the door.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
35.292.406/0
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Weider Home Gym 831150470 User Manual
Weil McLain Boiler SB0203 User Manual
Whirlpool Dishwasher WU3000 User Manual
Whirlpool Oven RS610PXGV10 User Manual
Whirlpool Washer GB AWE 7516 User Manual
Wolf Appliance Company Ventilation Hood PWC362418 User Manual
Wolfgang Puck Kitchen Grill BCGL0020 User Manual
Xerox Printer Accessories 4004 User Manual
Yamaha Automobile F25D User Manual
Zanussi Dishwasher ZDT 6244 User Manual