EN
User manual
2
Washing Machine
ZWF 14069W
Download from Www.Somanuals.com. All Manuals Search And Download.
• Always be sure, that there is no water leakage from
hoses and their connections after the installation.
• If the applianceis installed in a location subject tofrost,
please read the “dangers of freezing” chapter.
• Any plumbing work required to install this appliance
should be carried out by a qualified plumber or com-
petent person.
Child safety
• This appliance is not intended for use by person (in-
cluding children) with reduced physical sensory or
mental capabilities or lack of experience and knowl-
edge unless they have been given supervision or in-
struction concerning use of the appliance by a person
responsible for their safety.
• The packaging components (e.g. plastic film, poly-
styrene) can be dangerous to children - danger of suf-
focation! Keep them out of children’s reach
• Any electrical work required to install this appliance
should be carried out by a qualified electrician or com-
petent person.
• Keep all detergents in a safe place out of children’s
reach.
• Make sure that children or pets do not climb into the
drum. To prevent children and pets becoming trapped
inside the drum this machine incorporates a special
feature.
Use
• This appliance is designed for domestic use. It must
not be used for purposes other than those for which it
was designed.
• Only wash fabrics which are designed to be machine
washed. Follow the instructionsoneachgarmentlabel.
• Do not overload the appliance. See the Washing Pro-
gramme Table.
• Before washing, ensure that all pockets are empty and
buttons and zips are fastened. Avoid washing frayed or
torn articles and treat stains such as paint, ink, rust,
and grass before washing. Underwired bras must NOT
be machine washed.
• Garments which have been in contact with volatile pe-
troleum products should not be machine washed. If
volatile cleaning fluids are used, care should be taken
to ensure that the fluid is removed from the garment
before placing in the machine.
• Never pull the power supply cable to remove the plug
from the socket; always take hold of the plug itself.
To activate this device, ro- To disable this device and
tate the button (without
pressing it) inside the
restore the possibility of
closing thedoor, rotatethe
door clockwise until the button anti-clockwise un-
groove is horizontal. If
necessary use a coin.
til the groove is vertical.
• Never use the appliance if the power supply cable, the
control panel, the working surface or the base are
damaged so that the inside of the washing machine is
accessible.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product description
1
2
3
4
5
6
Detergent dispenser drawer
Control panel
Door opening handle
Rating plate
Drain pump
Adjustable feet
1
2
3
4
5
6
Detergent dispenser drawer
Compartment for detergent used for prewash and
soak phase or for stain remover used during the stain
action phase (if available). The prewash and soak deter-
gent is added at the beginning of the wash programme.
The stain remover is added during the stain action phase.
Compartment for powder or liquid detergent used for
main wash. If using liquid detergent pour it just before
starting the programme.
Compartment for liquid additives (fabric softener,
starch).
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in
the detergent dispenser drawer. Any fabric softener or
starching additives must be poured into the compartment
before starting the wash programme.
Control panel
Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and pilot
lights. These are presented by relevant numbers on the following pages.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
7
6
1
2
3
4
Programme selector dial
SPIN reduction button
OPTIONS button
5
6
7
START/PAUSE button
DELAY START button
Indicator pilot lights
EXTRA RINSE button
Table of symbols
Night Cycle
Rinse Hold
Programme selector dial, spin speed button and available options
in times with a more economical power rate. On some
programmestherinseswill beperformedwithmorewater.
Before opening the door it will be necessary to empty out
the water. To empty out the water, please read the para-
graph «At the end of the programme».
Programme Selector Dial
Itallowsyoutoswitchtheapplianceon/offand/ortoselect
a programme.
Available options:
Spin
By pressing this button you can change the spin speed of
the selected programme or to select the Rinse Hold or the
Night Cycle option.
Prewash
By selecting this option the machine performs a prewash
cycle before the main wash phase. The washing time will
be prolonged. This option is recommended for heavily
soiled laundry.
Rinse hold
By selecting this function the water of the last rinse is not
emptied out to prevent the fabrics from creasing. Before
opening the door it will be necessary to empty out the
water. To empty out the water, please read the paragraph
«At the end of the programme».
Economy
Only for cottons and synthetic items lightly or normally
soiled at a temperature of 40°C or higher. The washing
time will be prolonged and the washing temperature will
be reduced. You can use this option if you want to wash
normally soiled laundry and at the same time save energy.
Night Cycle
By selecting this function the machine will not drain the
water of the last rinse and all spinning phases will be
suppressed, so as not to wrinkle the laundry. This wash-
ing cycle is very quiet and it can be selected at night or
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Super Quick
Indicator pilot light (7)
Short cycle for lightly soiled items or for laundry which
needs only freshening up. We recommend you to reduce
the fabrics loading.
After having pressed the
button 5 the light 7.1
(Wash) and 7.2 (Door) il-
luminate to indicate that
appliance is working and
the door is locked.
Extra Rinse
This appliance is designed for saving energy. If it neces-
sary to rinse the laundry using an extra quantity of water
(extra rinse), select this option. Some additional rinses
will be performed. This option isrecommended for people
who are allergic to detergents, and in areas where the
water is very soft.
The light 7.2 (Door) indicates if the door can be opened:
• The light is on: the door cannot be opened.
• The light is off: the door can be opened.
Start Pause
This button allows you to start or to interrupt the selected
programme.
• The light is flashing: the door is unlocking and soon
can be opened.
The light 7.3 (End) illuminates at the end of the washing
cycle.
Delay Start
The start of the programme can be delayed by 2, 4 or 8
hours by means of this button.
First use
• Ensure that the electrical and water connections
comply with the installation instructions.
• Remove the polystyrene block and any material from
the drum.
• Pour 2 liters of water into the main wash compartment
of the detergent drawer in order to activate the
ECO valve. Then run a cotton cycle at the highest tem-
perature without any laundry in the machine, to remove
any manufacturing residue from the drum and tub.
Pour 1/2 a measure of detergent into the main wash
compartment and start the machine.
Daily use
Load the laundry
Measure out the detergent and the fabric softener
Open the door by carefully
pulling the door handle
outwards. Place the laun-
dry in the drum, one item
at a time, shaking them out
as much as possible.
Close the door.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the Delay Start by pressing button 6
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent required, pour it into the
Before you start the programme, if you wish to delay the
start, press the button 6 repeatedly, to select the desired
delay. The relevant light illuminates.
You must select this option after you have set the pro-
gramme and before you start the programme.
You can cancel or modify the delay time at any moment,
before you press button 5 .
main wash compartment
or in the appropriate com-
partment if the selected programme/option it requires
(see more details in "Detergent dispenser drawer").
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
«MAX» mark in the drawer). Close the drawer gently.
Selecting the delayed start:
1. Select the programme and the required options.
2. Select the delay start by pressing the button 6 .
3. Press button 5 :
Select the required programme by turning the
programme selector dial (1)
Turn the programme selector dial to the required pro-
gramme. The green pilot light of the button 5 starts to
flash.
– the machine starts its hourly countdown.
– The programme will start after the selected delay
The selector dial can be turned either clockwise or coun-
terclockwise. Turn to position « Off » to resetprogramme/
switch the machine off.
has expired.
Cancelling the delayed start after having started the pro-
gramme:
At the end of the programme the selector dial must be
turned to position «Off» , to switch the machine off.
1. Set the washing machine to PAUSE by pressing but-
ton 5 .
2. Press button 6 once, the light relevant to the selected
delay goes off
3. Press button 5 again to start the programme.
The Delay Start can not be selected with DRAIN pro-
gramme.
Caution! If you turn the programme selector dial to
another programme when the machine is working,
the red pilot light of button 5 will blink 3 times to indicate
a wrong selection. The machine will not perform the new
selected programme.
Select the spin speed, the Night Cycle or the Rinse Important! The selected delay can be changed only after
selecting the washing programme again.
Hold option by pressing button 2
The door will be locked throughout the delay time. If you
needtoopenthedoor, youmustsetthemachinetoPAUSE
(by pressing the button 5 ) and then wait a few minutes.
After you have closed the door, press the button 5 again.
The washing machine will automatically select the max-
imum spin value provided for the programme you have
chosen. (See "Washing programmes" for the maximum
allowed spin speed).
Press this button repeatedly to change the spin speed, if
you want your laundry to be spun at a different speed. The
relevant light will light up.
Start the programme by pressing button 5
To start the selected programme, press the button 5 , the
corresponding green pilot light stops blinking. The pilot
light corresponding to the running phase illuminates. The
appliance starts operating and the door is locked.
To interrupt a programme which is running, press the
button 5 : the corresponding green pilot light starts blink-
ing.
To restart the programme from the point at which it was
interrupted, press the button 5 again . If you have chosen
a delayed start, the machine will begin the countdown.
If an incorrect option is selected, the red pilot light of the
button 5 blinks 3 times.
Select the available options by pressing buttons 3
and 4
Depending on the programme, different functions can be
combined. These must be selected after choosing the de-
sired programme and before starting the programme.
When these buttons are pressed, the corresponding pilot
lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected, the inte-
grated red pilot light of the button 5 flashes for 3 times.
For the compatibility among the washing pro-
grammes and the options see chapter «Washing
Programmes».
7
Download from Www.Somanuals.com. All Manuals Search And Download.
If you cannot open the door but you need to open it you
have to switch the machine off by turning the selector dial
to Off position. After a few minutes the door can be opened
(pay attention to the water level and temperature!) .
After closing the door, it is necessary to select the pro-
gramme and options again and to press button 5 .
Altering an option or a running programme
It is possible to change some options before the pro-
gramme carries them out.
Before you make any change, you must PAUSE the ap-
pliance by pressing the button 5 .
Changing a running programme is possible only by re-
setting it. Turn the programme selector dialto Offand then
to the new programme position. Start the new programme
by pressing the button 5 again. The washing water in the
tub will be not emptied out.
At the end of the programme
The machine stops automatically. The pilot light of button
5 goes off and after a few minutes the 7.2 pilot light goes
off. The light 7.3 illuminates. The door can be opened.
If a programme or an option that ends with water left in
the tub has been selected, the light 7.2 illuminates and
the door remains locked to indicate that the water must
be emptied out before opening the door.
Follow the below instructions to empty out the water:
1. Turn the programme selector dial to Off .
2. Select the draining or spinning programme.
3. Reduce the spin speed if needed, by pressing the
relevant button.
4. Press button 5 .
At the end of the programme, the door can be now opened.
Turn the programme selector dial to Off to switch the ma-
chine off.
Remove the laundry from the drum and carefully check
that the drum is empty. If you do not intend to carry out
another wash, close the water tap. Leave the door open to
prevent the formation of mildew and unpleasant smells.
Interrupting a programme
Press the button 5 to interrupt a programme which is
running, the corresponding green pilot light starts blink-
ing.
Press the button again to restart the programme.
Cancelling a programme
Turn the selector dial to Off position to cancel a pro-
gramme which is running. Now you can select a new pro-
gramme.
Opening the door
After the programme has started the door is locked. If, for
any reason, you need to open it, set firstly the machine to
PAUSE by pressing the button 5 . After a few minutes the
pilot light 7.2 goes off and the door can be opened.
If the door remains locked, this means that the machine
is already heating or that the water level is too high. In
any case, do not try to force the door!
Helpful hints and tips
Treat curtains with special care. Remove hooks or tie them
up in a bag or net.
Sorting out the laundry
Follow the wash code symbols on each garment label and
the manufacturer’s washing instructions. Sort the laundry
as follows: whites, coloureds, synthetics, delicates, wool-
lens.
Removing stains
Stubborn stains may not be removed by just water and
detergent. It is therefore advisable to treat them prior to
washing.
Blood: treat fresh stains with cold water. For dried stains,
soak overnight in water with a special detergent then rub
in the soap and water.
Oil based paint: moisten with benzine stain remover, lay
the garment on a soft cloth and dab the stain; treat several
times.
Dried grease stains: moisten with turpentine, lay the gar-
ment on a soft surface and dab the stain with the fingertips
and a cotton cloth.
Before loading the laundry
Never wash whites and coloureds together. Whites may
lose their «whiteness» in the wash.
New coloured items may run in the first wash; they should
therefore be washed separately the first time.
Button up pillowcases, close zip fasteners, hooks and
poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special detergent or
detergent paste.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rust: oxalic acid dissolved in hot water or a rust removing • powder detergents for delicate fabrics (60°C max) and
product used cold. Be careful with rust stains which are
not recent since the cellulose structure will already have
been damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well (whites and fast
coloureds only).
woollens
• liquid detergents, preferably for low temperature wash
programmes (60°C max) for all types of fabric, or spe-
cial for woollens only.
The detergent and any additives must be placed in the
appropriate compartments of the dispenser drawer before
starting the wash programme.
If using liquid detergents, a programme without prewash
must be selected.
Your appliance incorporates a recirculation system which
allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in
the detergent dispenser drawer .
Grass: soap lightly and treat with bleach (whites and fast
coloureds only).
1)
Ball point pen and glue: moisten with acetone , lay the
garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone as above, then treat stains
with methylated spirits. Treat any residual marks with
bleach.
Red wine: soak in water and detergent, rinse and treat with
acetic or citric acid, then rinse. Treat any residual marks
with bleach.
Quantity of detergent to be used
Ink: depending on the type of ink, moisten the fabric first
The type and quantity of detergent will depend on the type
of fabric, load size, degree of soiling and hardness of the
water used.
Follow the product manufacturers’ instructions on quan-
tities to use.
Use less detergent if:
• you are washing a small load
1)
with acetone , then with acetic acid; treat any residual
marks on white fabrics with bleach and then rinse thor-
oughly.
Tar stains: first treat with stain remover, methylated spirits
or benzine, then rub with detergent paste.
Detergents and additives
Good washing results also depend on the choice of de-
tergent and use of the correct quantities to avoid waste
and protect the environment.
Although biodegradable, detergents contain substances
which, in large quantities, can upset the delicate balance
of nature.
The choice of detergent will depend on the type of fabric
(delicates, woollens, cottons, etc.), the colour, washing
temperature and degree of soiling.
All commonly available washing machine detergents may
be used in this appliance:
• the laundry is lightly soiled
• large amounts of foam form during washing.
Degrees of water hardness
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in your
area can be obtained from the relevant water supply com-
pany, or from your local authority. If the water hardness
degree is medium or high we suggest you to add a water
softenerfollowing alwaysthe manufacturer’sinstructions.
When the degree of hardness is soft, readjust the quantity
of the detergent.
• powder detergents for all types of fabric
1) do not use acetone on artificial silk
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Washing Programmes
Programme - Maximum and Minimum Temperature - Cycle
Description - Maximum Spin Speed - Maximum Fabrics Load
- Type of Laundry
Options
Detergent drawer
3)
COTTONS
90° - 60°
Main wash - Rinses
Maximum spin speed at 1400 rpm
Max. load 5,5 kg - Reduced load 2,5 kg
White cotton heavily or normally soiled items.
SPIN
1)
NIGHT CYCLE
RINSE HOLD
PREWASH
ECONOMY
SUPER QUICK
EXTRA RINSE
2)
3)
3)
3)
COTTONS
60° - 30°
Main wash - Rinses
Maximum spin speed at 1400 rpm
Max. load 5,5 kg - Reduced load 2,5 kg
Coloured cotton normally soiled items.
SPIN
NIGHT CYCLE
RINSE HOLD
PREWASH
ECONOMY
SUPER QUICK
EXTRA RINSE
4)
2)
SYNTHETICS
60° - 30°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 3 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured garments,
non-shrink shirts, blouses.
SPIN
NIGHT CYCLE
RINSE HOLD
PREWASH
ECONOMY
SUPER QUICK
EXTRA RINSE
4)
2)
DELICATES
40° - 30°
Main wash - Rinses
Maximum spin speed at 700 rpm
Max. load kg 3 - Reduced load kg 1,5
Delicate fabrics: acrylics, viscose, polyester.
NIGHT CYCLE
RINSE HOLD
PREWASH
SUPER QUICK
EXTRA RINSE
2)
WOOL
40°- 30°
Main wash - Rinses
SPIN
NIGHT CYCLE
RINSE HOLD
Maximum spin speed at 900 rpm
Max. load 2 kg
Washing programme for machine washable wool. Note : A
single or bulky item may cause imbalance. If the appliance
doesn’t perform the final spin phase, add more items, redis-
tribute the load manually and then select the spinning pro-
gramme.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme - Maximum and Minimum Temperature - Cycle
Description - Maximum Spin Speed - Maximum Fabrics Load
- Type of Laundry
Options
Detergent drawer
HAND WASH
40° - Cold
Main wash - Rinses
SPIN
NIGHT CYCLE
RINSE HOLD
Maximum spin speed at 900 rpm
Max. load 2 kg
Special programme for delicate fabrics with «hand washing»
care symbol.
3)
EASY IRON
SPIN
40°
RINSE HOLD
PREWASH
Main wash - Rinses
Maximum spin speed at 900 rpm
EXTRA RINSE
Max. load 1 kg
Synthetic or mixed fabrics : selecting this programme the laun-
dry is gently washed and spun to avoid any creasing. In this
way ironing is easier. Furthermore the machine will perform
additional rinses.
RINSE
Rinses
SPIN
NIGHT CYCLE
RINSE HOLD
EXTRA RINSE
Maximum spin speed at 1400 rpm
Max. load 5,5 kg
With this programme it is possible to rinse and spin cotton
garments which have been washed by hand. The machine per-
forms 3 rinses, followed by a final long spin.
Important!
The spin speed will automatically assume the setting for cotton
items. if required, reduce the spin speed.
DRAIN
Draining of water
Max. load 5,5 kg
For emptying out the water of the last rinse in programmes with
the option Rinse Hold or Night Cycle selected.
SPIN
SPIN
Drain
Maximum spin speed at 1400 rpm
Max. load 5,5 kg
Separate spin for hand washed garments and after programmes
with the Rinse Hold or Night Cycle option selected. You can
reduce the spin speed to the required level by pressing the
relevant button to adapt it to the fabrics to be spun.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme - Maximum and Minimum Temperature - Cycle
Description - Maximum Spin Speed - Maximum Fabrics Load
- Type of Laundry
Options
Detergent drawer
DELICATE SPIN
Drain
Maximum spin speed at 700 rpm
Max. load 3 kg
Separate spin for hand washed garments and after programmes
with the Rinse Hold or Night Cycle option selected. You can
reduce the spin speed to the required level by pressing the
relevant button to adapt it to the fabrics to be spun.
OFF
For cancelling the programme which is running or to switch
the machine off .
1) This programme at the temperature of 60° with the option ECONOMY selected, is the reference programme for the data entered in
the energy label, in compliance with EEC 92/75 standards. It can be selected for slightly or normally soiled cotton items. The
temperature will decrease and the washing time will be extended. This allows to obtain a good washing efficiency so saving energy.
2) If you select the Super Quick option by pressing button 3 , we recommend that you reduce the maximum load as indicated. Full
loading is possible however with somewhat reduced cleaning results.
3) If using liquid detergents, a programme without PREWASH must be selected.
4) This option is not active at a temperature lower than 40° C.
What to do if…
Certain problems are due to lack of simple maintenance
Once the problem has been eliminated, press the button
or oversights, which can be solved easily without calling 5 to restart the programme. If after all checks, the problem
out an engineer. Before contacting your local Service
Centre, please carry out the checks listed below.
During machine operation it is possible that the red pilot
light of button 5 blinks to indicate that the machine is not
working.
persists, contact your local Service Centre.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause/Solution
The door has not been closed (the button 5 red light blinks).
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The washingmachinedoesnotstart: The main fuse has blown.
• Replace the fuse.
The programme selector dial is not correctly positioned and the button 5 has
not been pressed.
• Please turn the selector dial and press the button 5 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The water tap is closed (the button 5 red light blinks).
• Open the water tap.
The inlet hose is squashed or kinked (the button 5 red light blinks).
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked (the button 5 red
light blinks).
The machine does not fill:
• Clean the water inlet filters. (See "Cleaning the water inlet filters" for more
details).
The door is not properly closed (the button 5 red light blinks).
• Close the door firmly.
The drain hose is squashed or kinked (the button 5 red light blinks).
• Check the drain hose connection.
The drain filter is clogged (the button 5 red light blinks).
• Clean the drain filter.
An option or a programme that ends with the water still in the tub or a that
eliminates all the spinning phases has been selected.
The machine does not empty and/or
does not spin:
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause/Solution
Too much detergent or unsuitable detergent (creates too much foam) has been
used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if it is
damp.
There is water on the floor:
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The emergency emptying cap has not been replaced into the filter cover or the
filter has not been properly screwed in after cleaning action.
• Refit the emergency emptying cap into the filter cover or screw the filter
fully in.
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
Unsatisfactory washing results:
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait a few minutes before opening the door.
There is water in the drum.
The door will not open:
• Select drain or spin programme to empty out the water.
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted.
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
The machine vibrates is noisy:
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause/Solution
The electronic unbalance detection device has cut in because the laundry is
not evenly distributed in the drum. The laundry is redistributed by reverse
rotation of the drum. This may happen several times before the unbalance
disappears and normal spinning can resume. If, after 10 minutes, the laundry
is still not evenly distributed in the drum, the machine will not spin. In this
case, redistribute the load manually and select the spin programme.
Spinning starts late or the machine
does not spin:
• Redistribute the laundry.
The load is too small.
• Add moreitems, redistribute the load manually and then selectthe spinning
programme.
If you are unable to identify or solve the problem, contact
our service centre. Before telephoning, make a note of the
model, serial number and purchase date of your machine:
the Service Centre will require this information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Technical data
Dimensions
Width
Height
Depth
60 cm
85 cm
60 cm
63 cm
Depth (Overall dimensions)
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate, on the
inner edge of the appliance door.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Spin Speed
Cotton
5,5 kg
Maximum
1400 rpm
Consumption values
Programme
Energy consumption
(KWh)
Water consumption (litres) Programme duration (Mi-
nutes)
White Cottons 90°
Cottons 60°
1.9
1.2
58
54
49
130
120
140
Cottons + ECONOMY 60°
1)
0.93
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme
Cottons 40°
Energy consumption
(KWh)
Water consumption (litres) Programme duration (Mi-
nutes)
0.6
0.5
54
50
50
53
115
80
Synthetics 40°
Delicates 40°
Wool 30°
0.55
0.25
65
55
1) «Cottons + Economy» at 60°C with a load of 5,5 kg is the reference programme for the data entered in the energy label, in
compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
Care and cleaning
Warning! You must DISCONNECT the appliance
from the electricity supply, before you can carry out
any cleaning or maintenance work.
Descaling
The water we use normally contains lime. It is a good idea
to periodically use a water softening powder in the ma-
chine. Do this separately from any laundry washing, and
according to the softening powder manufacturer's in-
structions. This will help to prevent the formation of lime
deposits.
Remove the drawer by
pressing the catch down- part of the additive com-
wards and by pulling it partment should be re-
out. Flush it out under a moved.
tap, to remove any traces
To aid cleaning, the top
External cleaning
Clean the exterior cabinet of the appliance with soap and
water only, and then dry thoroughly.
of accumulated powder.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
Cleaning the drawer recess
Having removed the draw-
er, use a small brush to
clean the recess, ensuring
that all washing powder
residue is removed from
the upper and lower part of
the recess.
Replace the drawer and run the rinse programme with-
out any clothes in the drum.
Cleaning the pump
The pump should be inspected if:
• the machine does not empty and/or spin;
16
Download from Www.Somanuals.com. All Manuals Search And Download.
• the machine makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump.
Proceed as follows:
• disconnect the appliance;
Never removethepumpcoverduringawashcycle, always
wait until the appliance has finished the cycle, and is
empty. When replacing the cover, ensure it is securely re-
tightened so as to stop leaks and young children being
able to remove it.
• if necessary wait until the water has cooled down.
Cleaning the water inlet filters
Important! If the appliance doesn't fill, takes long to fill
water, the starting button blinks yellow or the display (if
available) shows the relevant alarm (see chapter "What to
do if..." for more details), check if the water inlet filters are
blocked .
Open the pump door.
Place a container close to
the pump to collect any
spillage.
To clean the water inlet filters:
• Turn off the water tap.
• Unscrew the hose from
the tap.
• Clean the filter in the
hose with a stiff brush.
Pull out the emergency
emptying hose, place it in
the container and remove
its cap.
• Screw the hose back onto the tap. Make sure the
connection is tight.
When no more water comes out, unscrew the pump
cover and remove it. Always keep a rag nearby to dry
up spillage of water when removing the cover.
Remove any objects from
the pump impeller by ro-
tating it.
Put the cap back on the
emergency emptying hose
and place the latter back in
its seat.
• Unscrew the hose from the machine. Keep a rug
nearby because some water may flow.
• Clean the filter in the valve with a stiff brush or with
the piece of cloth.
Screw the pump cover
fully in.
Close the pump door.
35°
45°
Caution! When the appliance is in use and
depending on the programme selected there can be
hot water in the pump.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• Screw the hose back to the machine and make sure
the connection is tight.
• Turn on the water tap.
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until water stops
flowing out;
• clean the pump if necessary as previously described;
• replace the emergency emptying hose in its seat after
having plugged it;
Frost precaution
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
• Turn off the water tap.
• Unscrew the inlet hose.
• Place the end of the emergency emptying hose and that
of the inlet hose in a bowl placed on the floor and let
water drain out.
• Screw the water inlet hose back on and reposition the
emergency emptying hose after having put the cap on
again.
• When you intend to start the machine up again, make
sure that the room temperature is above 0°C.
• screw the pump cover again and close the door.
Important! Every time you drain the water through the
emergency emptying hose you must pour 2 litres of water
into the main wash compartment of the detergent drawer
and then run the drain programme. This will activate the
ECO Valve device avoiding that part of the detergent
remains unused at next washing.
Emergency emptying out
If the water is not discharged, proceed as follows to empty
out the machine:
Installation
Unpacking
All transit bolts and packing must be removed before us-
ing the appliance.
You are advised to keep all transit devices so that they
can be refitted if the machine ever has to be transported
again.
Unscrew the three bolts. Slide outtherelevantplas-
tic spacers.
After removing all the
packaging, carefully lay
Remove the power supply
cable and the hoses from
machine on it's back to re- the hose holders on the
move thepolystyrenebase rear of the appliance.
from the bottom.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
The inlet hose is screwed to the back of the appliance.
Connect the hose to a tap
with a 3/4” thread. Always
use the hose supplied with
the appliance.
Open the porthole and re- Fill the smaller upper hole
move the polystyrene
block fitted on the door
seal.
and the two large ones
with the corresponding
plastic plug caps supplied
in the bag containing the
instruction booklet.
35°
45°
Positioning
Install the machine on a flat hard floor. Make sure that air
circulation around the machine is not impeded bycarpets,
rugs etc. Check that the machine does not touch the wall
or other kitchen units. Level the washing machine by
raising or lowering the feet. The feet may be tight to adjust
as they incorporate a self locking nut, but the machine
MUST be level and stable.
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and displace-
ment of the machine during operation. Never place card-
board, wood or similar materials under the machine to
compensate for any unevenness in the floor.
The other end of the inlet hose which connects to the
appliance can be turned as showed in the picture.
Do not place the inlet hose downwards. Angle the hose
to the left or right depending on the position of your
water tap. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks.
Caution! The inlet hose must not be lengthened. If
it is too short and you do not wish to move the tap,
you will have to purchase a new, longer hose specially
designed for this type of use.
If necessary, check the
setting with a spirit level.
Warning! Installation should comply with local
water authority and building regulations’
requirements.
The appliance must be connected to a cold water supply.
A minimum water pressure of 0.05 MPa (0.5 bar) is
required for safe operation of the appliance.
If you cannot make the cold water connection direct from
the rising mains, you may be able to operate the appliance
from your cold water storage system.
Water inlet
There should be a minimum vertical distance of 5.02 m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
Warning! This appliance must be connected to a
cold water supply
Caution! Before connecting up the appliance to new
pipework or to pipework that has not been used for
some time, run off a reasonable amount of water to flush
out any debris that may have collected
Water drainage
This appliance is designed to be permanently plumbed
into your home's drainage system using one of the fol-
lowing methods.
Caution! Do not use the hose from your previous
appliance to connect to water supply.
1. Into a drainage standpipe.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Onto a sink outlet spigot.
Firstly form a hook in the end of the drain hose using
the “U” piece” supplied.
Loop
“U” piece supplied
If the outlet spigot has not Push the drain hose onto
been used before, remove the spigot and secure with
Place the drain hose into your standpipe, which should
have an internal diameter of approximately 38 mm thus
ensuring there is an air break between the drain hose
and standpipe.
When discharging into a standpipe ensure that the top
of the standpipe is no more than 90 cm (35.4'') and no
less than 60 cm (23.6'') above floor level.
any blanking plug that
may be in place.
a clip, ensure a loop is
formed in the drain hose
(see above) to prevent
waste from the sink enter-
ing the appliance.
If you intend to drain the hose from the machine into a
sink, make sure that the sink is empty and the plug hole
is not blocked. Use the plastic “U - Piece” supplied.
38 mm (1.5”)
standpipe
diamater
30 cm (12”)
Special conditions
If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to pre-
vent noise, vibration or displacement. The base should
protrude a few centimetres beyond the edges of the ap-
pliance.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre. The
joining piece must have an internal diameter of 18 mm.
Warning! The appliance should NOT be placed on
deep pile carpeting.
Note!
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
In the interest of the environment
The appliance should be connected to the FOUL drainage
system, the water will then be taken to a sewage works for
treatment before being discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is dis-
charged directly into a river or stream and may cause
pollution.
Min. 60 cm (23.6”)
Max. 90 cm (35.4”)
If your drain hose looks
like this (see beside) you
do not require the “U”
piece”. Just push the hose
firmly in to the standpipe.
If you require any further advice please contact your local
water authority.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
Green & Yellow
Brown
Cord clamp
Blue
1
SHOWER
TOILET
SINK
BATH
BIDET
2
WASHING
MACHINE
3
4
DISHWASHER
RAINWATER
‘RUN-OFF’
The wire coloured green and yellow must be connected
to the terminal marked with the letter «E» or by the earth
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
FOUL SEWERS
symbol
or coloured green and yellow.
The wire coloured blue must be connected to the terminal
«N» or coloured black.
The wire coloured brown must be connected to the ter-
minal marked «L» or coloured red.
SEWAGE TREATMENT
WORKS
TREATED DISCHARGE
RIVER
UNTREATED
DISCHARGE
RIVER
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or com-
petent person.
Warning! A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard.
Warning! THIS APPLIANCE MUST BE EARTHED.
Ensure that the cut off plug is disposed of safely. Should
The manufacturer declines any liability should this the appliance power supply cable need to be replaced,
safety measure not be observed.
this must be carried out by our Service Force Centre. The
appliance should not be connected to the electricalsupply
by means of an extension cable.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate.
Note!
Warning! Information on the electrical connection
is given on the rating plate on the inner edge of the
appliance door.
When the appliance is installed the power supply cable
must be accessible.
Permanent connection
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3 mm between the switch contacts and of a typesuitable
for the required load in compliance with the current elec-
trical regulations.
The appliance is supplied with a 13 amp plug fitted.
In the event of having to change the fuse in the plug sup-
plied, a 13 amp ASTA approved (BS1363/A) fuse must be
used.
Should the plug need to be replaced for any reason, pro-
ceed as described below.
The switch must not break the yellow and green earth
cable at any point.
The wires in the mains lead are coloured in accordance
with the following code:
Environment concerns
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
information about recycling of this product, please
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
21
Download from Www.Somanuals.com. All Manuals Search And Download.
• Normally soiled laundry may be washed without pre-
washing in order to save detergent, water and time (the
environment is protected too!).
• The machine works more economically if it is fully
loaded.
• Withadequatepre-treatment, stainsandlimitedsoiling
can be removed; the laundry can then be washed at a
lower temperature.
contactyourlocalcouncil, yourhouseholdwastedisposal
service or the shop where you purchased the product.
Packaging materials
The materials marked with the symbol are recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This meansthatthey can be recycled by disposingofthem
properly in appropriate collection containers.
• Measure out detergent according to the water hard-
ness, the degree of soiling and the quantity of laundry
being washed.
Ecological hints
To save water, energyandto helpprotecttheenvironment,
we recommend that you follow these tips:
22
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|