REFRIGERATOR - FREEZER
ZX77/3 ZX77/5
ZX79/3 ZX79/5
INSTRUCTION BOOKLET
214.3660.55
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Instructions for the User
Instructions for the Installer
Safety Instructions
2
3
Technical Specifications
Installation
13
Description of the Appliance
Control Panel
14
14
14
14
14
15
15
16
4
Unpacking
Using the Appliance
Before Use
5
Positioning
5
Ventilation
Starting the Appliance
Freezer Compartment
Freezing Fresh Food
Frozen Food Storage
Refrigerator Compartment
Chill Compartment
5
Leveling
5
Electrical Connection
Electrical Requirements
Changing the Opening direction
of the Doors
5
5
5
5
Food Storage
6
Energy Saving Advice
In the Event of a Power Failure
Maintenance and Cleaning
Something Not Working
Normal Operating Sounds
Service & Spare Parts
Customer Care Department
Guarantee Conditions
6
6
7
8
9
9
9
10
Zanussi Service Force
11 - 12
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
These warnings are provided in the interests of your safety. Ensure that you unders-
tand them all before installing or using this appliance. If you are unsure of the mea-
nings of these warnings contact the Customer Care Department.
Bottles and cans must not be placed in the fre-
ezer compartment as they can burst as the con-
tents freeze.
Installation
This appliance is heavy. Care should be taken
when moving it.
Manufacturers recommended food storage
times should be adhered to. Refer to the rele-
vant instructions.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
Ensure that the appliance does not stand on the
electrical supply cable. If the supply cable is dama-
ged, it must be replaced by a cable available from
your local Service Force Centre.
Do not use electrical appliances inside the frid-
ge / freezer.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Maintenance and Cleaning
Before cleaning, always switch off the applian-
ce and disconnect from the electrical supply.
When unplugging always pull the plug from the
mains socket, do not pull on the cable.
Parts which heat up should not be exposed. Whe-
never possible, the back of the appliance should be
close to a wall, but leaving the required distance for
ventilation, as stated in the installation instructions.
The appliance should be left for 2 hours after insta-
llation before it is turned on, in order to allow the
refrigerant to settle.
Servicing
This product should be serviced by an authori-
sed engineer and only genuine spare parts
should be used.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried
out by inexperienced persons may cause injury
or serious malfunction. Contact your local
Zanussi Service Force Centre.
Child Safety
Do not allow children to tamper with the controls or
play with the product.
Keep all packaging material away from children.
During Use
Disposing of Old Appliances
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs only.
It is not intended for commercial or industrial use.
Containers with flammable gases or liquids can
leak at low temperatures. Do not store any contai-
ners with flammable materials, such as spray cans,
fire extinguisher refill cartridges etc. in the refrige-
rator.
Remove the doors to prevent small children
being trapped in side. Cut off and dispose of
the plug and cable.
Use an authorised disposal site.
Frozen food should not be refrozen once it has tha-
wed out.
Keep this instruction book
for future reference and
ensure it is passed on to
any new owner
Do not place carbonated or fizzy drinks in the free-
zer compartment.
Ice lollies can cause frost/freezer burns if consu-
med straight from the freezer compartment.
Do not remove items from the freezer compartment
if your hands are damp/wet, as this could cause
skin abrasions or frost/freezer burns.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of Appliance
The model shown here is ZK77/5W
0
7
3
7
3
5
5
C
O
L
L
E
C
T
I
O
N
3
6
9
12
Control Panel
1
2
3
Freezer Temperature Control
Fridge Temperature Control
ON/OFF Button
4
5
6
Door Alarm
Temperature Alarm
Fast Freezer Button
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. ON/OFF Button
Control Panel
To switch the appliance on or off, press the
ON/OFF button continuously for 3 seconds. When
the appliance is switched on, the ON/OFF button
and the Freezer and Fridge control knobs will be
illuminated.
The appliance controls are located in the top panel insi-
de the refrigerator compartment.
Thermostat Control
The freezer and fridge thermostats control the tempe-
rature inside the freezer and refrigerator respectively.
4. The Door Alarm
If either of the doors are left open, the door alarm
will sound and the alarm button will flash red. Press
the alarm button to switch off the alarm, the light
will stop flashing but will remain red. To switch off
the alarm and the light shut the doors.
1. The Freezer Temperature Control
The freezer temperature control, regulates the tempe-
rature within the freezer compartment. A change in the
control setting in the freezer compartment could affect
the temperature in the refrigerator compartment under
certain circumstances.
5. Temperature Alarm
If the internal temperature inside the appliance is
too high for the safe storage of frozen food, an
alarm will sound and the temperature alarm button
light will start to flash. The temperature may rise for
the following reasons:
7 Maximum coldness
1 Minimum coldness
An intermediate position is usually the most suitable,
although the temperature will be affected by:
The doors have been left open
There has been a power failure
Room temperature
How often the door is opened
How much food is stored
Position of the appliance
A large quantity of food has been added to the
appliance.
In determining the correct temperature control setting
all these factors have to be considered and some
experimentation may be necessary.
The thermostat controls may be incorrectly set.
There is a fault.
When altering the temperature settings, allow 24 hours
for the temperature to stablise before making further
changes.
To switch off the alarm, press the alarm button. The
audible signal will stop. The light will stop flashing,
but will remain on until the internal temperature has
reached the correct storage temperature for frozen
food.
2. The Fridge Temperature Control
The fridge temperature control regulates the tempera-
ture within the fridge compartment, by regulating the
cold airflow. An intermediate setting is usually the most
suitable, although some experimentation may be
necessary to obtain the correct temperature.
6. Fast Freeze Button
Press the fast freeze button approximately 3 hours
before freezing fresh food. Once the food is frozen,
switch off the fast freeze function by pressing the
fast freeze button. The fast freeze function will self
cancel after 36 hours.
5 Maximum coldness
1 Minimum coldness
Standby
Turn the control knob to the standby position if you
wish to switch off the fridge, but leave the freezer in
operation (for example, when on holiday). Leave the
doors shut when in Standby operation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing Fresh Food
Using the Appliance
The maximum quantity of food that can be frozen in
24 hours shown on the rating plate and in the tech-
nical specifications section of this instruction book.
This appliance is designed for domestic
use only, specifically for storage of edible
foodstuffs.
When freezing fresh foods, press the fast freeze
button 3 hours before placing the food into the fre-
ezer compartment.
This appliance is designed to operate in ambient tem-
peratures (surrounding air temperature) between 10°C
(50°F) and 32°C (90°F).
If these temperatures are exceeded i.e. colder or war-
mer, the appliance may not operate correctly.
When the food is frozen, switch off the fast freeze
function. The fast freeze function will self cancel
after 36 hours.
The Temperature alarm may sound if a lot of new
food is put into the freezer, due to a rise in tempe-
rature. The alarm will switch off automatically, as
the freezer temperature drops. Push the alarm but-
ton to switch off the audible signal.
Before Use
Remove all transit packaging.
Wash the inside of the appliance with lukewarm water
with a little bicarbonate of soda added (5ml to 0.5 litre
of water). Do not use soap or detergent as the smell
may linger. Dry the appliance thoroughly.
Frozen Food storage
The freezer will store frozen food at -18°C or colder
allowing for long term frozen food storage and fre-
ezing of fresh food.
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax
polishes or products containing alcohol.
Pre packed commercially frozen food should be
stored in accordance with the manufacturers ins-
tructions for a 4 star frozen food compartment and
should be put in the freezer as soon as possible
after purchase. Your freezer provides for long-term
storage which generally means up to 3 months but
the length of the time can vary and it is important to
follow the recommended times shown on packets
of commercially frozen food.
Starting the Appliance
1. Allow the appliance to stand for 2 hours after insta-
llation.
2. Plug in the appliance and switch on at the mains
supply. Press the ON/OFF button continuously for 3
seconds. The appliance will start operating after a 4
minute delay and the internal light will switch on.
The ON/OFF button will illuminate green and the
Freezer and Fridge control knob surrounds light up.
Refrigerator Compartment
This compartment is designed to store drinks and
fresh food. The inner temperature is normally uni-
form and is kept cool by cold circulating air. Try to
avoid putting food products flush against the air
vents at the back of the fridge as this could cause
the foods to freeze.
The temperature alarm (a beeping sound) may
come on during the start up phase. If this happens
push the temperature alarm button.
3. Set the thermostat controls for the fridge and free-
zer compartments. See Control Panel section.
Chill Compartment
4. To ensure safe food storage, allow the appliance to
operate with the doors closed for at least 3 hours,
before loading with food.
The temperature is kept typically at 1-2 degrees
lower than the average temperature in the fridge.
Use the compartment for foods that are marked
typically for storage at 0-5°C for longer preserva-
tion. Adjusting the fridge temperature to cooler or
warmer affects the chiller temperature in the same
way. Avoid stacking large amounts of warm food on
top of already cold food, as this will raise the tem-
perature of the food previously stored in the chiller.
Do not use the chiller, as a zone for rapid cooling at
it is not designed for this.
Freezer Compartment
The freezer will store frozen food at -18°C or colder
allowing for long-term frozen food storage and freezing
of fresh food.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Food Storage
Energy Saving Advice
Ensure that food placed in the freezer is dated
and labeled and used in date order to ensure
that food is consumed at its best.
Do not install the cabinet close to sources of heat,
such as a cooker, dishwasher or radiator.
Locate the appliance in a cool well-ventilated room
and make sure that the air openings of the cabinet
are not obstructed.
Remove suspect food from your fridge freezer
and clean, refer to Maintenance and Cleaning.
Do not put any newly introduced food for free-
zing near to already frozen food
Avoid unnecessary frosting in the cabinet by pac-
king all foodstuffs into airtight packages before pla-
cing them in the freezer.
Food and drinks, which have a strong odor,
may affect other foods and drinks if not stored
correctly.
Always leave warm food to cool down to room tem-
perature before placing in the fridge or freezer.
Food that is to be frozen (when cool) should be pla-
ced in the fridge before being transferred to the fre-
ezer.
In the Event of a Power
Failure
If there is a power failure during the storage of fro-
zen foods, keep the door closed. If the temperatu-
re within your freezer should rise do not refreeze
the food without checking its condition. The follo-
wing guidelines should assist you.
Ice Cream: Once thawed should be discarded.
Fruit and Vegetables: If soft should be cooked
and used up.
Do not put any hot food into the fridge or freezer.
Thaw frozen food in the fridge. This will ensure
safer defrosting of foods and reduce the work of the
refrigeration unit.
Try to avoid keeping the door open for long periods,
or opening the door too frequently as warm air will
enter the cabinet, and cause the compressor to
switch on unnecessarily often.
Bread and Cakes: Can be refrozen without dan-
ger.
Ensure there are no obstructions preventing the
door from closing properly.
Shellfish: Should be refrigerated and used up
quickly.
Cooked Dishes: i.e. casseroles should be refrige-
rated and used up.
To obtain the best results from your appliance, neit-
her hot foods nor liquids, which may evaporate
should be placed in the larder compartment.
Large Pieces of Meat: Can be re-frozen providing
there are ice crystals remaining within them.
Small Joints: Should be cooked and then re-fro-
zen as cooked dishes.
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated container is
advisable. When you arrive home place the frozen
food in the freezer immediately.
Chicken:
Should be cooked and re-frozen as a fresh dish.
Keep the time between buying chilled food and pla-
cing it in your fridge as short as possible.
Do not push food together too much; try to allow air
to circulate around each item.
Do not store food uncovered.
Wrap the food up properly or place it in airtight con-
tainers before putting it into the fridge freezer.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Defrosting
Your appliance is frost free, which means there is
no need to manually defrost your appliance, as this
will be carried out automatically.
Maintenance and
Cleaning
Before any maintenance or cleaning work
is carried out DISCONNECT the applian-
ce from the ELECTRICITY supply.
Changing the light bulb
1. Switch off the appliance by pressing the
ON/OFF button, and then unplug the appliance.
3. Open the plastic light cover, by pushing
upwards on the centre clip. The cover will then
swing down.
External Cleaning
Wash the outer cabinet with warm soapy water.
4. Unscrew the light bulb and replace with a bulb
with the following specifications:
Do not use abrasive products.
There may be sharp edges on the under-
side of the product so care should be
taken when cleaning.
Clear Halogen
E14 screw thread
220-240 Volts
25 watts (max)
Ensure the vents at the back of the appliance are clear
of dust and debris etc.
Internal Cleaning
Clean the inside and accessories with warm water and
bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
1 halogen bulb 25W
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax
polishes or cleaning products containing
bleach or alcohol.
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all of
the food and clean the inside of the appliance.
Switch off the appliance and leave the door ajar to
prevent unpleasant smells.
Regularly check the door seals and wipe clean to ensu-
re they are clean and free from debris.
Cleaning the Condenser
Glass Shelves
The Condenser at the bottom of your appliance needs
to be cleaned periodically. Remove the plinth, and
clean with a vacuum cleaner. Ensure the plinth is repla-
ced after cleaning.
The shelf on the vegetable drawer is secured by
two tabs. To release and remove the vegetable
drawer and glass shelf, it is necessary to rotate the
tabs as shown in detail B (Tabs A are previously
removed transit packaging).
NOISE REDUCTION PAD
(DONT REMOVE)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Not Working
If your appliance is not operating correctly, carry out the following checks before contacting your local Service
Force Centre.
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or ins-
tallation a charge will be made, even if the appliance is under guarantee.
Symptom
Cause
Solution
Interior Light (refrigerator)
Appliance is not plugged in
The appliance is not switched on
There is no power to the appliance
Plug in the appliance
Switch on the appliance
Check the main fuse box in the
house
does not work
The bulb is not fitted correctly or
has fused.
Refit the bulb or replace with a
new bulb
The appliance does not cool The doors have not been closed
Close the doors
down sufficiently
properly
A door has been opened frequently
Avoid frequent opening of the
doors
The temperature control knob is
not set correctly
Reset as required
Food has been introduced into the
appliance
The appliance will cool down in
due course.
Food is freezing in the fridge The temperature control knob
is incorrectly set
Reset as required
Food is too close to ventilation
holes at the back
Reposition food, leaving a gap.
Change the setting
The motor works
continuously.
Temperature control knob is
incorrectly set
The doors are not properly closed
Close the doors
Doors have been opened frequently Avoid frequent opening of the doors
Food has recently been introduced
into the appliance
The appliance will cool down in
due course.
The condenser is dirty
Clean (read the Maintenance &
Cleaning section).
Water/condensation in the
vegetable drawer
Wet vegetables have been put
into the box
This may occur from time to time
Condensation on the
outside of the cabinet
High humidity level in the room.
It does not affect the performance
of the appliance. Increase the
room ventilation.
Doors do not close
The appliance is not level
The doors are incorrectly aligned
Food is preventing the doors
shutting
Level the appliance correctly
Re-align the doors
Re-position food
Noises
The appliance may not be level
Something may be vibrating inside
Level the appliance
Check the contents and shelves
are properly positioned.
Contact your local Service
Force Centre
All product lights start
Your product has a major fault
flashing and the alarm sounds
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal Operating Sounds
1.
2.
3.
4.
Temperature control
May cause clicking sounds when the system is connected or disconnected.
Cooling system
The injected cooling gas may produce a gurgling sound while passing through the tubes.
Motor
May cause a humming noise and or slight knocking sound.
Fans
You may occasionally hear the fans working. This is normal; the fans help to ensure the air circulates
more effectively.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Zanussi Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area. The
addresses are listed on the following pages.
Before calling out an engineer, please ensure you have read the details under the heading «Something Not Wor-
king».
When you contact the Service Centre you will need to give the following details.
1.
2.
3.
4.
5.
Your name, address and postcode
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance (found on the rating plate)
The purchase date
Customer Care Department
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please
contact our Customer Care Department by letter or telephone at the address below or visit our website at
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 *
* Calls to this number may be recorded for training purposes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option
repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufactu-
rer's instructions.
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorized by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
Any appliance or defective part replaced shall become the Company's property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs
or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance, which is improperly installed, or calls to appliances outsi-
de the United Kingdom.
Appliances found to be in use within a commercial environment, plus those, which are subject to rental agre-
ements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within European Community (EC) or European Free Trade Area. The product is installed
and used in accordance with our instructions and is only used domestically, i.e. a normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care Centre, listed below, to give them details of
your new home. They will then ensure that the local Service Organisation is aware of your move and able
to look after you and your appliance.
France Senlis +33 (0) 44 62 29 29
Germany Nuremberg +49 (0) 0800 358 9737
Italy Pordenone +39 (0) 0434 39 4700
Sweden Stockholm +46 (0) 8 672 53 90
UK Slough +44 (0) 1753 219897
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Zanussi Service Force
To contact your local Zanussi Service Centre telephone 08705 929 929
ORKNEY
7 King Street
Kirkwall
CHANNEL ISLANDS
NORTH EAST
Orkney
KW15 1JF
GUERNSEY
Guernsey Electricity
PO Box 4
Vale, Guernsey
GATESHEAD
Unit 356a
Dukesway Court
Dukesway
PERTH
Scottish Hydro Electric
Central Warehouse
Inveralmond
Channel Islands GY1 3AD
Gateshead NE11 0BH
JERSEY
Jersey Electricity Company
Haut De Lorme
Rue De Haut De Lorme
Trinity
Jersey
Channel Islands JE3 3FG
(OWN SALES)
EDINBURGH
Perth PH1 3AF
GRIMSBY
HULL
15 Hainton Avenue
Grimsby
N.E. Lincs
Unit 12
Dumbryden Ind. Estate
2 Dumbryden Road
Edinburgh
DN32 9AS
Unit 1
EH14 2AB
SCOTLAND
Boulevard Industrial Estate
Hull
HU3 4AY
SHETLAND
3-4 Carlton Place
Lerwick
Shetland
ABERDEEN
54 Claremont Street
Aberdeen AB10 6RA
LEEDS
64-66 Cross Gates Road
Cross Gates
Leeds
(OWN SALES)
SHETLAND
ZE1 0PW
AUCHTERMUCHY 33a Burnside
Auchtermuchy
Bolts Shetland
26 North Road
Lerwick
Fife KY14 7AJ
LS15 7YS
BLANTYRE
Unit 5
Block 2
Auchenraith Ind. Estate
Rosendale Way
Blantyre G72 0NJ
NEWTON AYCLIFFE Unit 23
Northfield Way
(OWN SALES)
WHALSAY
Shetland ZE1 0PE
Aycliffe Industrial Park
Newton Aycliffe
DL5 6EJ
Leask Electrical
Harisdale
Symbister, Whalsay
Shetland ZE2 9AA
(OWN SALES)
DUMFRIES
DUNOON
93 Irish Street
Dumfries
DG1 2 PQ
SHEFFIELD
Pennine House
Roman Ridge Road
Sheffield
NORTHERN IRELAND
S9 1GB
7 Hill Street
Dunoon
Argyll
BELFAST
Owenmore House
Kilwee Business Park
Dunmurry
Belfast
BT17 0HD
NORTH WEST
PA23 7AL
BIRKENHEAD
CARLISLE
1 Kelvin Park
Dock Road
Birkenhead
CH41 1LT
GLASGOW
Unit 4
Wellington Road
Bishopriggs
WALES
Glasgow G64 2SA
Unit 7
CARDIFF
CLYWD
DYFED
Unit 4
James Street Workshops
James Street
Carlisle
Guardian Industrial Estate
Clydesmuir Road
Cardiff
INVERNESS
Unit 3BI
Smithton Ind. Estate
Smithton
Cumbria
CA2 5AH
CF2 2QS
Inverness IV2 7WL
ISLE OF MAN
BOLTON
South Quay Ind. Estate
Douglas
Isle of Man
Unit 6-7 Coed Parc
Abergele Road
Rhuddlan
Clwyd
LL18 5UG
ISLE OF ARRAN R Haggerty
Bruach
Blackwaterfoot
Isle of Arran
IM1 5AT
Unit B
ISLE OF BARRA J Zerfah
Central Industrial Estate
St Marks Street
Bolton
Unit 9
244 Bruernish
Isle of Barra
Western Islands HS9 5QY
St. Clears Business Park
Tenby Road
St. Clears
BL3 6NR
Carmarthen
SA33 4J
ISLES OF BUTE Walker Engineering
PRESTON
Unit 250
Glenmhor
Upper Serpentine Road
Rothesay
Dawson Place
Bamber Bridge
Preston
OSWESTRY
Plas Ffynnon Warehouse
Middleton Road
Oswestry
Isle of Bute PA20 9EH
Lancashire PR5 8AL
SY11 2PP
ISLE OF LEWIS
KELSO
ND Macleod
16 James Street
Stornoway
STOCKPORT
Unit 20 Haigh Park
Haigh Avenue
Stockport
Isle of Lewis PA87 2QW
SK4 1QR
2, 6 & 8 Woodmarket
Kelso
Borders
TD5 7AX
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Zanussi Service Force
To contact your local Zanussi Service Centre telephone 08705 929 929
MIDLANDS
LONDON & EAST ANGLIA
SOUTH EAST
BIRMINGHAM
66 Birch Road East
Wyrley Trading Estate
Wilton
Birmingham
B6 7DB
BECKENHAM
11a Gardener Ind. Estate
Kent House Lane
Beckenham
ASHFORD
FLEET
Unit 2
Bridge Road Business Est.
Bridge Road
Ashford
Kent BR3 1QZ
Kent TN23 1BB
CHELMSFORD
COLINDALE
Hanbury Road
Widford Ind Estate
Chelmsford
Essex
BOURNE
Pinfold Road
Bourne
PE10 9HT
Unit 1
Redsfield Ind. Estate
Church Crookham
Fleet
CM12 3AE
BRIDGNORTH
68 St. Marys Street
Bridgnorth
Hampshire GU13 0RD
Unit 14
Shropshire
WV16 4DR
Capitol Park
Capitol Way
Colindale
HAYWARDS
HEATH
21-25 Bridge Road
Haywards Heath
Sussex RH16 1UA
GLOUCESTER
HEREFORD
101 Rycroft Street
Gloucester
GL1 4NB
London NW9 0EQ
TONBRIDGE
Unit 30
ELTHAM
194 Court Road
Mottingham
Eltham
Deacon Trading Estate
Morley Road
Tonbridge
Unit 3 & 4
Bank Buildings
Cattle market
Hereford
London SE9 4EW
TN9 1RA
ENFIELD
284 Alma Road
Enfield
London
HE4 9HX
SOUTH WEST
HIGHAM FERRERS 30 High Street
Higham Ferrers
EN3 7BB
BARNSTAPLE
Main Road
Fremington
Northants
GRAVESEND
Unit B4
Barnstaple
NN10 8PL
Imperial Business Estate
West Mill
North Devon EX31 2NT
ILKESTON
Unit 2
Furnace Road
Ilkeston DE7 5EP
Gravesend
Kent
DA11 0DL
BOURNEMOUTH 63-65 Curzon Road
Bournemouth
Dorset
BH1 4PW
LEICESTER
Unit 7
LETCHWORTH
LONDON
16-17 Woodside Ind. Estate
Works Road
Letchworth
Herts
SG6 1LA
Oaks Industrial Estate
Coventry Road
Narborough
Leicestershire
LE0 5GF
BRIDGEWATER
BRISTOL
6 Herswell Business Park
Salmon Parade
Bridgewater
Somerset TA6 5PY
2 - 4 Royal Lane
Yiewsley
11 Eldon Way
LINCOLN
Unit 8
Eldonwall Trading Estate
Bristol
Avon BS4 3QQ
Clifton Street
Stonefield Park
Lincoln
West Drayton
Middlesex
UB7 8DL
LN5 8LQ
EMSWORTH
266 Main Road
Southbourne
Emsworth
MAIDENHEAD
MOLESEY
Reform Road
Maidenhead
Berkshire
NEWCASTLE
UNDER LYME
18-21 Croft Road
Brampton Ind. Estate
Newcastle under Lyme
Staffordshire
PO10 8JL
SL6 8BY
ISLE OF WIGHT Unit 8
Enterprise Court
ST5 0TW
10 Island Farm Avenue
West Molesey
Surrey
Ryde Business Park
Ryde
Isle of Wight PO33 1DB
REDDITCH
13 Thornhill Road
North Moons Moat
Redditch
KT8 2UZ
Worcestershire
B98 9ND
NEWBURY
9 Pipers Court
Berkshire Drive
Thatcham
Berkshire
RG19 4ER
NEWTON ABBOT Unit 2
Zealley Ind. Estate
Kingsteignton
Newton Abbot
TQ12 3TD
TAMWORTH
WORCESTER
Unit 3
Sterling Park
Claymore
Tamworth
B77 5DQ
IPSWICH
Unit 6C
REDRUTH
Unit 7D
Elton Park Business Centre
Hadleigh Road
Ipswich
Pool Ind. Estate
Wilson Way
Redruth
Units 1 & 2
Northbrook Close
Gregorys Mill Ind. Estate
Worcester
IP2 0DD
Cornwall TR15 3QW
NORWICH
SUNBURY
2b Trafalgar Street
Norwich
NR1 3HN
WR3 8BP
Unit 1a
The Summit
Hanworth Road
Sunbury on Thames
TW16 5DB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
A distance of 56mm must exist between the appliance and the wall, to allow the door to be fully opened.
The refrigeration system and the insulation of this appliance do not contain CFCs or HCFCs.
ZX79/5W(SI)
2010
ZX77/5W(SI)(SA)
ZX77/3W(SI)
1710
ZX79/3W(SI)
1860
Height (mm)
1860
595
Width (mm)
595
595
595
Depth (mm)
670
670
670
670
Power Supply
220-240V / 50Hz 220-240V / 50Hz 220-240V / 50Hz 220-240V / 50Hz
Total Power Absorbed
Energy Consumption kWh/year
kWh/day
602
492.75
1.35
10
584
507.35
1.39
10
529
438.00
1.20
9
584
478.15
1.31
9
Freezing Capacity (Kg/24hrs)
Gross Capacity (ltrs/cu.ft)
Fridge
246/8.7
130/4.6
205/7.3
130/4.6
205/7.3
95/3.4
246/8.7
95/3.4
Freezer
Net Capacity (ltrs/cu.ft)
Fridge
242/8.6
95/3.4
200/7.1
95/3.4
200/7.1
68/2.4
242/8.6
68/2.4
Freezer
*
This figure is based on standard test results in accordande with European Standard EN 153. Actual con-
sumption will depend on how the appliance is used and where it is located.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Unpacking
Remove all transit packaging, including the door transit
retainers located under the plinth. (Fig 1) and shelf
retainers (Fig 2).
Fig. 1
Positioning
The appliance should be located in a well-ventilated,
dry room. To ensure correct operation the appliance
should:
Not be exposed to direct sunlight.
Not be installed next to radiators, cookers or other
sources of heat.
Fig. 2
Only be installed in a location where the ambient
temperature corresponds to the climate classifica-
tion for which the appliance is designed.
The climate classification can be found on the rating
plate, which is located on the bottom, left hand side of
the fridge compartment. The table shows the correct
operating ambient temperature for each climate class.
(Fig 3)
rating
plate
Climate Classification Ambient Operating Temp.
SN
N
ST
T
+10 to +32°C
+16 to +32°C
+18 to +38°C
+18 to +43°C
Fig. 3
If the temperature rises above or falls below the stated
ambient temperature for the climate class, the opera-
tion of the appliance may be affected.
Ventilation
You should also ensure that air can circulate freely
around the back and the top of the cabinet.
Never put something on the ventilator grill of the
appliance (see fig. 4)
Leveling
Level the appliance by turning the 2 adjustable feet at
the front of the appliance. The appliance must be level
to prevent vibration and excessive noise and to ensure
the doors shut correctly. (Fig 5)
Fig. 4
Fig. 5
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Any electrical work required to install this
appliance must be carried out by a quali-
fied electrician or competent person.
This appliance must be earthed.
The manufacturer declines any liability
should these safety measures not be
observed.
Electrical Requirements
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance
rating plate.
The appliance is supplied with a 13 amp plug fitted. In
the event of having to change the fuse in the plug sup-
plied, a 13 amp ASTA approved (BS 1362) fuse must
be used.
Should the plug need to be replaced for any reason,
the wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
The wire coloured green and yellow must be connec-
ted to the terminal marked with the letter E or by the
earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the ter-
minal marked N or coloured black.
The wire coloured brown must be connected to the ter-
minal marked L or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure
over the outer sheath.
Important
If the mains supply cable is damaged, it must be repla-
ced by a cable available from your local Service Force
Centre.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the opening direction of the doors
If you wish to change the opening direction of the
doors, proceed as follows:
B
1. Open the freezer door. Remove the plinth (A) at the
bottom of the appliance, by pushing downwards
and pulling outwards. (See fig 5)
2. Remove the hinge cover (B) in the plinth and repo-
sition on the opposite side of the plinth.
3. Whilst supporting the lower door, use a 8mm nut
driver to remove the 4 hinge retaining bolts and
remove the lower hinge.
4. Carefully lower the door off the central hinge.
5. Support the upper door and remove the two secu-
ring screws from the centre hinge. Remove the
hinge, taking care that the upper door does not fall,
A
retain the plastic spacer washer.
Fig. 8
6. Carefully remove the upper door.
7. Unscrew the small blanking plugs (3) and refit on
the opposite side to cover the vacant hinge holes.
8. Unscrew the hinge pin (4) in the upper and lower
hinge blades and refit on the opposite side.
9. Change the door self-closing system (5), putting
the freezer doors on the fridge door and viceversa.
10. Refit the spacer washers and the upper door onto
the upper hinge pin and refit the centre hinge in
position.
11. Relocate the lower door onto the central hinge pin,
and refit the lower hinge assembly.
12. Refit the plinth.
After reversing the door ensure the internal light turns
off when the fridge door is closed, and the door gasket
seals correctly to the cabinet. If the gasket is not sea-
ling correctly, apply warm air to the non-sealing area
using a hair dryer set to gentle heat.
This will make the rubber more supple and allow it to
revert to its original shape and seal correctly.
Fig. 9
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|