Zanussi Range ZWF 16581 User Manual

User  
manual  
Washing  
Machine  
ZWF 16581 W  
ZWF 16581 S  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety information  
In the interest of your safety and to ensure  
the correct use, before installing and first  
using the appliance, read this user manual  
carefully, including its hints and warnings.  
To avoid unnecessary mistakes and  
accidents, it is important to ensure that all  
people using the appliance are thoroughly  
familiar with its operation and safety  
features. Save these instructions and make  
sure that they remain with the appliance if it  
is moved or sold, so that everyone using it  
through its life will be properly informed on  
appliance use and safety.  
Always unplug the appliance and turn off the  
water supply after use, clean and  
maintenance.  
Under no circumstances should you attempt  
to repair the machine yourself. Repairs  
carried out by inexperienced persons may  
cause injury or serious malfunctioning.  
Contact your local Service Centre. Always  
insist on genuine spare parts.  
Installation  
This appliance is heavy. Care should be  
taken when moving it.  
When unpacking the appliance, check that it  
is not damaged. If in doubt, do not use it and  
contact the Service Centre.  
All packing and transit bolts must be  
removed before use. Serious damage can  
occur to the product and to property if this is  
not adhered to. See relevant section in the  
user manual.  
After having installed the appliance, check  
that it is not standing on the inlet and drain  
hose and the worktop is not pressing the  
electrical supply cable.  
If the machine is situated on a carpeted floor,  
please adjust the feet in order to allow air to  
circulate freely  
General safety  
It is dangerous to alter the specifications or  
attempt to modify this product in any way.  
During high temperature wash programmes  
the door glass may get hot. Do not touch it!  
Make sure that small pets do not climb into  
the drum. To avoid this, please check into  
the drum before using.  
Any objects such as coins, safety pins, nails,  
screws, stones or any other hard, sharp  
material can cause extensive damage and  
must not be placed into the machine.  
Only use the advised quantities of fabric  
softener and detergent. Damage to the fabric  
can ensue if you over-fill. Refer to the  
manufacturer’s recommendations of  
quantities.  
Always be sure, that there is no water  
leakage from hoses and their connections  
after the installation.  
Wash small items such as socks, laces,  
washable belts etc in a washing bag or  
pillow case as it is possible for such items to  
slip down between the tub and the inner  
drum.  
Do not use your washing machine to wash  
articles with whalebones, material without  
hems or torn material.  
If the appliance is installed in a location  
subject to frost, please read the «dangers of  
freezing» chapter.  
Any plumbing work required to install this  
appliance should be carried out by a  
qualified plumber or competent person.  
Any electrical work required to install this  
appliance should be carried out by a  
qualified electrician or competent person.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Make sure that children or pets do not climb  
into the drum. To avoid this the machine  
incorporates special feature.  
Use  
This appliance is designed for domestic use.  
It must not be used for purposes other than  
those for which it was designed.  
Only wash fabrics which are designed to be  
machine washed. Follow the instructions on  
each garment label.  
Do not overload the appliance. See the  
relevant section in the user manual.  
Before washing, ensure that all pockets are  
empty and buttons and zips are fastened.  
Avoid washing frayed or torn articles and  
treat stains such as paint, ink, rust, and  
grass before washing. Underwired bras must  
NOT be machine washed.  
Garments which have been in contact with  
volatile petroleum products should not be  
machine washed. If volatile cleaning fluids  
are used, care should be taken to ensure  
that the fluid is removed from the garment  
before placing in the machine.  
To activate this device, To disable this device  
rotate the button  
and restore the  
(without pressing it)  
inside the door  
possibility of closing the  
door, rotate the button  
anti-clockwise until the  
groove is vertical.  
clockwise until the  
groove is horizontal. If  
necessary use a coin.  
Never pull the power supply cable to remove  
the plug from the socket; always take hold of  
the plug itself.  
Never use the washing machine if the power  
supply cable, the control panel, the working  
surface or the base are damaged so that the  
inside of the washing machine is accessible.  
Child safety  
This washing machine is not intended for  
use by young children or infirm persons  
without supervision.  
Young children should be supervised to  
ensure that they do not play with the  
appliance.  
The packaging components (e.g. plastic film,  
polystyrene) can be dangerous to children -  
danger of suffocation! Keep them out of  
children’s reach  
Keep all detergents in a safe place out of  
children’s reach.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Description of the appliance  
Your new washing machine is fitted with an automatic device which detectes the laundry amount  
in some programmes for cotton and synthetic items and chooses the best cycles parameters for  
washing in an economical way. Cycle time duration, energy and water consumptions are  
proportional to the amount of each load.  
It is ideal when washing different small quantities of laundry.  
1
Detergent dispenser drawer  
1
2
2
3
4
5
Control panel  
Door opening handle  
Drain pump  
Delay Start  
Off  
Jetsystem+  
Cotton  
Cotton Eco  
Synthetic  
Cottons  
Normal  
Sport 40°  
Sport Shoes 40°  
Wool  
95º  
60º  
40º  
30º  
1600  
900  
Handwash  
700  
Heavy  
Normal  
Light  
Silk  
+Prewash  
+Superquick  
Lock  
Duvet  
1600 7kg  
Start/Pause  
Extra Rinse  
Soil Level  
Easy Iron  
Temp.  
Spin  
Mini 30'  
Normal  
Special  
Rinse  
Drain  
+Prewash  
+Superquick  
ZWF16581W  
S
p
i
n
D
e
l
i
c
a
t
e
Synthetics  
Adjustable feet  
3
4
5
Detergent dispenser drawer  
Prewash  
Wash  
Fabric Softener  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Control panel and functions  
Delay Start  
Off  
Jetsystem+  
Cotton Eco  
Synthetic  
Sport 40°  
Sport Shoes 40°  
Wool  
Cotton  
1600  
900  
95º  
60º  
40º  
30º  
Cottons  
Normal  
Handwash  
700  
Heavy  
Normal  
Light  
Silk  
+Prewash  
+Superquick  
Lock  
Duvet  
Start/Pause  
Extra Rinse  
Easy Iron  
Soil Level  
Spin  
Temp.  
Mini 30'  
Normal  
Special  
Rinse  
Drain  
+Prewash  
+Superquick  
ZWF16581W  
Spin Delicate  
Synthetics  
6
8
9
1
2
3
4
5
7
The programme selector dial allows to select a programme  
and/or to switch the machine on/off. It can be turned either  
clockwise or anticlockwise. The light Start/Pause starts to  
flash.  
Programme selector dial and  
On/Off switch  
1
2
Press this button repeatedly to change the washing  
temperature, if you want your laundry to be washed at a  
temperature different from the one proposed by the washing  
machine. The relevant light will light up.  
Temperature button  
Press the Spin button repeatedly to change the spin speed,  
if you want your laundry to be spun at a speed different from  
the one proposed by the washing machine. The relevant  
light will light up.  
Spin reduction button  
Soil level button  
3
4
By means of this button, you can select the soil level option:  
Heavy, Normal, Light (see the relevant chapter «Operating  
sequence»).  
The relevant light will light up.  
Selecting this button the laundry is gently washed and spun  
to avoid any creasing. In this way ironing is easier.  
Easy iron button  
5
6
By means of this button, the machine performs some  
additional rinses.  
Extra Rinse button  
The display shows the following information: duration of the  
selected programme, washing programme phase icons,  
delayed start, weight calculation phase, incorrect option  
selection, alarm codes, child safety option, heating phase  
and end of programme.  
Display  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
The Start/Pause button allows to start the selected  
programme; the corresponding green pilot light stops  
flashing.  
Start/Pause button  
Delay Start buttons  
8
9
This button interrupts also a programme which is running, the  
corresponding green pilot light starts to flash.  
By means of this buttons, the wash programme can be  
delayed from 30 min - 60 min - 90 min, 2 hours and then by  
1 hour up to a maximum of 20 hours .  
Programme table - Proportional programmes  
Programme/  
Temperature  
Description of  
programme  
Type of laundry  
Options  
White and coloured  
Main wash from 95°C  
Cotton  
95 -  
Proportional  
Spin red.  
cotton (Normally soiled):  
e.g. sheets, tablecloths,  
household linen, towels.  
to  
Cold  
Heavy, Light,  
3 rinses  
Long spin  
Easy iron, Extra rinse  
White and fast  
coloured cotton  
(normally or lightly soiled  
items): sheets, household  
linen, underwear  
Main wash from 95°C to  
40°C  
2 rinses  
Cotton Eco  
60- 40  
proportional  
Spin red.  
Easy iron  
Extra rinse  
Long spin  
Synthetic or mixed  
fabrics, underwear,  
coloured garments, non-  
shrink shirts, blouses.  
Main wash from 60°C  
Synthetic  
60 -  
proportional  
Spin red.  
Heavy, Light,  
Easy iron, Extra rinse  
to  
Cold  
3 rinses  
Short spin  
Cycle time duration, energy and water consumptions are proportional to the amount of load.  
Important!  
When selcting these programmes the «Normal» pilot light illuminates.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme table  
Programme/  
Temperature  
Description of  
programme  
Type of laundry  
Options  
White and coloured  
cotton cotton (normally  
soiled items): sheets,  
tablecloths, household  
linen, towels.  
Main wash from 95°C  
Cottons  
Normal  
95 -  
Spin red.  
Heavy, Easy iron,  
Extra rinse  
to  
Cold  
3 rinses  
Long spin  
White and coloured  
cotton (heavy soiled  
cotton items): sheets,  
household linen,  
Prewash at 30°C  
Main wash from 60°C to  
Cold  
3 rinses  
Long spin  
Cottons  
Spin red.  
Heavy, Easy iron  
Extra rinse  
+ Prewash  
95 -  
underwear  
White cotton (slightly  
soiled items): e.g.  
sheets, tablecloths,  
household linen, towels.  
Main wash from 95°C  
Cottons  
+ SuperQuick  
95 -  
to  
Cold  
Spin red.  
2 rinses  
Long spin  
Easy iron, Extra rinse  
Synthetic or mixed  
fabrics, underwear,  
coloured garments, non-  
shrink shirts, blouses.  
Main wash from 60°C  
Synthetics  
Normal  
60 -  
Spin red.  
to  
Cold  
Easy iron,  
Extra rinse  
3 rinses  
Short spin  
Prewash at 30°C  
Main wash from  
Synthetic or mixed  
fabrics, underwear,  
coloured garments, non-  
shrink shirts, blouses.  
Synthetics  
Spin red.  
Easy Iron  
Extra rinse  
60° to  
Cold  
+ Prewash  
60 -  
3 rinses  
Short spin  
Main wash from  
Synthetics  
Spin red.  
Synthetic or mixed  
fabrics lightly soiled  
60° to  
Cold  
+ SuperQuick  
60 -  
Easy iron,  
Extra rinse  
2 rinses  
Short spin  
Main wash from  
Delicates  
40-  
Delicate fabrics, for  
example curtains.  
40°C to  
Cold  
3 rinses  
Short spin  
Extra Rinse  
Max load for Cottons ..............................7.0 kg  
Max load for Synthetics ..........................3.5 kg  
Max load for Delicates ............................3.5 kg  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme table - Special programmes  
Programme/  
Temperature  
Description of  
programme  
Type of laundry  
Options  
Main Wash at 30°C  
2 rinses  
Short spin  
Short cycle for lightly  
soiled fabrics  
Mini 30’  
30  
Main Wash at 30°C  
3 rinses  
Short spin  
Duvet  
30  
Short cycle for blankets  
Main wash at 30°C  
2 rinses  
Short spin  
Silk items to be gentle  
washed and spun.  
Silk  
30  
Main wash from  
Handwash  
40 -  
Special programme for  
hand washing fabrics  
40° to  
Cold  
Spin red.,  
,
,
3 rinses  
Short spin  
Programme for wool  
«Pure new wool, non-  
shrink, machine  
Main wash from  
Wool  
40 -  
40° to  
Cold  
Spin red.,  
Spin Red./  
3 rinses  
Short spin  
washable» label.  
Short cycle for 1 pair of  
sport shoes (2 pairs if  
they are small)  
Main Wash at 40°C  
3 rinses  
Short spin  
Sport Shoes 40°  
40  
Extra rinse  
Prewash at 30°C  
Main wash at 40°C  
3 rinses  
Sport 40°  
40  
Programme for heavily  
soiled synthetics items  
Spin Red./  
,
Extra rinse  
Short spin  
Max load for Wool/Handwash/Duvet ........ 2 kg Max load for Sport Shoes 40° ................1 pair  
(2 pairs if they are small)  
Max load for Mini 30’/Sport 40° ............ 2.5 kg  
Max load for Silk ........................................1 kg  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Programme table  
Programme/  
Temperature  
Description of  
programme  
Type of laundry  
Options  
Separate spin for  
cottons.  
Spin  
Spin red.  
Drain and long spin  
For emptying out the last  
rinse water in  
programmes with the  
Drain  
Rinse  
Draining of water  
Rinse Hold  
or Night  
Cycle option.  
Separate rinse cycle  
for hand washed  
items of all fabric.  
3 rinses  
Long spin  
Spin red.  
Easy iron, Extra rinse  
Programme information  
Washing programme for machine washable wool as well as for hand  
washable woollens and delicate fabrics with the «hand washing»  
Wool and  
Handwash  
care symbol  
.
Selecting this button the laundry is gently washed and spun to avoid  
any creasing. In this way ironing is easier. Furthermore the machine  
will perform additional rinses.  
Easy Iron  
On cotton programmes the spin speed will automatically reduced to  
900 rpm.  
With this programme it is possible to rinse and spin cotton garments  
which have been washed by hand.  
The machine performs 3 rinses, followed by a final spin at maximum  
speed.  
Rinse  
Drain  
The spin speed can be reduced by depressing Spin button.  
For emptying out the water of the last rinse in cotton programmes  
with the Rinse Hold  
and Night Cycle  
option.  
Turn first the programme selector dial to «Off», then select  
programme Drain and depress the Start/Pause button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Programme information  
Separate spin for hand washed garments and after programmes  
with Rinse Hold and Night Cycle option. Before selecting  
this programme the selector dial must be turned to Off. You can  
choose the speed by means of the relevant button to adapt it to the  
fabrics to be spun.  
Spin  
This special short programme is a complete washing cycle for lightly  
soiled mixed fabrics /synthetic items or laundry which needs  
freshening up. The short spin is performed at 700 rpm. The cycle  
duration is about 30 minutes.  
Mini 30’  
Washing programme for a single synthetic duvet, blanket,  
bedspread etc. The washing temperature is 30°C. The spin is  
performed at 700 rpm.  
Duvet  
Silk  
Delicate washing programme suitable for silk and mixed synthetics  
items. Washing temperature is 30°C.  
The maximum spin speed is automatically reduced to 700 rpm.  
With this programme it is possible to wash one pair of sport shoes  
(or 2 pairs if they are small). The shoes would be gently washed and  
spun. Washing temperature 40°C.  
Sport shoes 40°  
Note! Don't wash your sport shoes together with laundry.  
This programme is suitable for washing heavily soiled sport items of  
synthetic fabrics. The machine will add automatically a prewash  
phase before the main wash to eliminate mud stains.  
Sport 40°  
Note ! We recommend you not to put the detergent into the  
compartent  
of the detergent drawer.  
The spin speed is reduced to 900 rpm.  
To reset a programme and to switch off the machine turn the  
selector dial to Off. Now can a new programme be selected.  
Off = Cancelling  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Washing hints  
Sorting the laundry  
Maximum loads  
Follow the wash code symbols on each  
garment label and the manufacturer’s washing  
Recommended loads are indicated in the  
programme charts.  
instructions. Sort the laundry as follows: whites, General rules:  
coloureds, synthetics, delicates, woollens.  
Cotton, linen: drum full but not too tightly  
packed;  
Synthetics: drum no more than half full;  
Delicate fabrics and woollens: drum no more  
than one third full.  
Washing a maximum load makes the most  
efficient use of water and energy.  
For heavily soiled laundry, reduce the load  
size.  
Temperatures  
for normally soiled white cottons  
90° or 95°  
50°/60°  
and linen (e.g. tea cloths, towels,  
tablecloths, sheets...)  
for normally soiled, colour fast  
garments (e.g. shirts, night  
dresses, pyjamas....) in linen,  
cotton or synthetic fibres and for  
lightly soiled white cotton (e.g.  
underwear).  
Laundry weights  
The following weights are indicative:  
bathrobe  
napkin  
quilt cover  
sheet  
pillow case  
tablecloth  
1200 g  
100 g  
700 g  
500 g  
200 g  
250 g  
200 g  
100 g  
200 g  
100 g  
600 g  
200 g  
500 g  
100 g  
100 g  
for delicate items (e.g. net  
curtains), mixed laundry including  
synthetic fibres and woollens  
bearing the label «pure new wool,  
machine washable, non-shrink».  
30°-40°-  
(Cold)  
Before loading the laundry  
Never wash whites and coloureds together.  
Whites may lose their «whiteness» in the  
wash.  
New coloured items may run in the first wash;  
they should therefore be washed separately  
the first time.  
Make sure that no metal objects are left in  
the laundry (e.g. hair clips, safety pins,  
pins). Button up pillowcases, close zip  
fasteners, hooks and poppers. Tie any belts  
or long tapes.  
Remove persistent stains before washing.  
Rub particularly soiled areas with a special  
detergent or detergent paste.  
Treat curtains with special care. Remove hooks  
or tie them up in a bag or net.  
towelling towel  
tea cloth  
night dress  
ladies’ briefs  
man’s work shirt  
man’s shirt  
man’s pyjamas  
blouse  
men’s underpants  
Removing stains  
Stubborn stains may not be removed by just  
water and detergent. It is therefore advisable to  
treat them prior to washing.  
Blood: treat fresh stains with cold water. For  
dried stains, soak overnight in water with a  
special detergent then rub in the soap and  
water.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Oil based paint: moisten with benzine stain  
remover, lay the garment on a soft cloth and  
dab the stain; treat several times.  
etc.), the colour, washing temperature and  
degree of soiling.  
All commonly available washing machine  
detergents may be used in this appliance:  
Dried grease stains: moisten with turpentine,  
lay the garment on a soft surface and dab the  
stain with the fingertips and a cotton cloth.  
Rust: oxalic acid dissolved in hot water or a  
rust removing product used cold. Be careful  
with rust stains which are not recent since the  
cellulose structure will already have been  
damaged and the fabric tends to hole.  
Mould stains: treat with bleach, rinse well  
(whites and fast coloureds only).  
Grass: soap lightly and treat with bleach  
(whites and fast coloureds only).  
Ball point pen and glue: moisten with  
acetone (*), lay the garment on a soft cloth and  
dab the stain.  
Lipstick: moisten with acetone as above, then  
treat stains with methylated spirits. Remove  
any residual marks from white fabrics with  
bleach.  
Red wine: soak in water and detergent, rinse  
and treat with acetic or citric acid, then rinse.  
Treat any residual marks with bleach.  
Ink: depending on the type of ink, moisten the  
fabric first with acetone (*), then with acetic  
acid; treat any residual marks on white fabrics  
with bleach and then rinse thoroughly.  
Tar stains: first treat with stain remover,  
methylated spirits or benzine, then rub with  
detergent paste.  
powder detergents for all types of fabric,  
powder detergents for delicate fabrics (60°C  
max) and woollens,  
liquid detergents, preferably for low  
temperature wash programmes (60°C max)  
for all types of fabric, or special for woollens  
only.  
The detergent and any additives must be  
placed in the appropriate compartments of the  
dispenser drawer before starting the wash  
programme.  
If using concentrated powder or liquid  
detergents, a programme without prewash  
must be selected.  
The washing machine incorporates a  
recirculation system which allows an optimal  
use of the concentrated detergent.  
Pour liquid detergent into the dispenser drawer  
compartment marked  
the programme.  
just before starting  
Any fabric softener or starching additives must  
be poured into the compartment marked  
before starting the wash programme.  
Follow the product manufacturer’s  
recommendations on quantities to use and do  
not exceed the «MAX» mark in the  
detergent dispenser drawer.  
(*) do not use acetone on artificial silk.  
Detergents and additives  
Good washing results also depend on the  
choice of detergent and use of the correct  
quantities to avoid waste and protect the  
environment. Although biodegradable,  
detergents contain substances which, in large  
quantities, can upset the delicate balance of  
nature.  
The choice of detergent will depend on the  
type of fabric (delicates, woollens, cottons,  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Quantity of detergent to be used  
Degrees  
Level Characteristic  
The type and quantity of detergent will depend  
on the type of fabric, load size, degree of  
soiling and hardness of the water used.  
Water hardness is classified in so-called  
«degrees» of hardness. Information on  
hardness of the water in your area can be  
obtained from the relevant water supply  
company, or from your local authority.  
Follow the product manufacturers’ instructions  
on quantities to use.  
German  
°dH  
French  
°T.H.  
1
2
3
4
soft  
medium  
hard  
0-7  
0-15  
16-25  
26-37  
> 37  
8-14  
15-21  
> 21  
very hard  
Use less detergent if:  
you are washing a small load,  
the laundry is lightly soiled,  
Degrees of water hardness  
Follow the product manufacturers’ instructions  
large amounts of foam form during washing.  
on quantities to use.  
Before the first use  
WARNING!  
Ensure that the electrical and water  
connections comply with the installation  
instructions.  
IMPORTANT!  
Remove the polystyrene block and any  
material from the drum.  
IMPORTANT!  
We recommend you to run run a cotton cycle  
at 95°C, without any laundry in the machine, to  
remove any manufacturing residue from the  
drum and tub. Pour 1/2 a measure of detergent  
into the dispenser drawer and start the  
machine.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Operating sequence  
Cottons,  
Synthetics,  
Special  
Turn the programme selector dial to the  
required programme.  
The Start/Pause light starts to flash, the display  
shows the duration of the selected  
programme.and the display shows the duration  
of the selected programme.The green  
Start/Pause light starts to flash.  
1. Load the laundry  
Open the door by  
carefully pulling the  
door handle outwards.  
Place the laundry in the  
drum, one item at a  
time, shaking them out  
as much as possible. Close the door.  
2. Measure out the detergent and the fabric  
softener  
Position «Off» to Reset programme/Switching  
OFF of the machine.  
At the end of the programme the selector  
dial must be turned to position «Off», to  
switch the machine off.  
IMPORTANT!  
If you turn the programme selector dial to  
another programme when the machine is  
working, the red Start/Pause pilot light will  
flash 3 times and the message Err is displayed  
on the display to indicate a wrong selection.  
The machine will not perform the new selected  
programme.  
Pull out the dispenser drawer until it stops.  
Measure out the amount of detergent required,  
pour it into the main wash compartment  
and, if you wish to carry out a programme with  
the prewash phase, pour it into the  
compartment marked  
If required, pour fabric softener into the  
compartment marked  
must not exceed the «MAX» mark in the  
drawer). Close the drawer gently.  
.
4. Select the temperature  
95º  
60º  
40º  
30º  
(the amount used  
Temp.  
3. Select the required programme  
Off  
Jetsystem+  
Cotton Eco  
Synthetic  
Sport 40°  
Sport Shoes 40°  
Wool  
Cotton  
Cottons  
Handwash  
Normal  
Press this button repeatedly to increase or  
decrease the temperature, if you want your  
laundry to be washed at a temperature  
different from the one proposed by the washing  
machine.Maximum temperatures are 95°C for  
Cottons, 60°C for Synthetics, 40°C for  
Silk  
+Prewash  
+Superquick  
Duvet  
Mini 30'  
Special  
Normal  
Rinse  
Drain  
+Prewash  
+Superquick  
Spin Delicate  
Synthetics  
The selector dial is divided into following the  
sections:  
Delicate, Wool, Handwash, Sport Shoes 40°  
and Sport 40°, 30°C for Silk, Duvet and Mini  
30’, while  
corresponds to cold wash.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Operating sequence  
5. Select the spin speed or Night Cycle or  
Rinse Hold option  
appears a flashing zero «0.00», the «Lock»  
light is alight and the door is locked to indicate  
that the water must be emptied out.  
1600  
900  
To empty out the water:  
700  
1. turn the programme selector dial to «Off»  
2. select the Drain or Spin programme  
Spin  
3. reduce the spin speed if needed, by means  
of the relevant button  
4. depress Start/Pause button  
Press the Spin button repeatedly to change the  
spin speed, if you want your laundry to be spun  
at a speed different from the one proposed by  
the appliance.  
5. at the end of programme, the display shows  
a flashing zero «0.00» and the «Lock» light  
goes off (and it will be possible to open the  
door).  
The relevant light will light up.  
6. Select the Soil Level option  
Maximum speeds are:  
Cottons: 1600 rpm;  
Synthetics, Wool, Wandwash, Sport Shoes  
40° and Sport 40°: 900 rpm  
Heavy  
Press the «Soil Level»  
button repeatedly, to  
Normal  
Light  
Soil Level  
increase or decrease  
Delicate, Mini 30’, Duvet and Silk: 700 rpm;  
the time cycle duration  
for cotton and synthetic.  
The relevant light will  
light up.  
Night Cycle  
: by selecting this option, the  
machine will not drain the water of the last  
rinse, so as not to crease the laundry. As all  
spinning phases are suppressed, this washing  
cycle is very noiseless and it can be  
selectionned at night or in times with a more  
economical power rate.  
IMPORTANT!  
Not all the soil levels are compatible and  
can be selected with any programme.  
Heavy  
On Cotton, Synthetics, Delicates, Silk, Sport  
Shoes 40° and Sport 40° programmes the  
rinses will be performed with more water.  
When the programme has finished, the  
Start/Pause light goes off, the display shows a  
flashing zero «0.00», the «Lock» light is alight  
and the door is blocked to indicate that the  
water must be emptied out.  
Select this option for heavily soiled laundry.  
The washing intensity will be increased and the  
washing time will be prolonged by about 10  
minutes.  
Normal:  
Select this option for normally soiled laundry .  
Depending on the selected programme, the  
corresponding «Normal » light will  
illuminate by default.  
Rinse Hold  
: by selecting this option the  
water of the last rinse is not emptied out to  
prevent the fabrics from creasing.  
Light:  
Select this option for slightly soiled items that  
have been used or worn for a short time.  
When the programme has finished, the  
Start/Pause light goes off, on the display  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
Operating sequence  
The washing intensity will be decreases and the  
washing time will be reduced by few xminutes.  
the Start/Pause button will flash 3 times.  
9. Display  
7 Select the Easy Iron option  
The display shows the following information:  
Duration of the selected programme  
After selecting a programme, the duration is  
displayed in hours and minutes (for example  
2.05). The duration is calculated automatically  
on the basis of the maximum recommended  
load for each type of fabric.  
Selecting this button the  
laundry is gently  
washed and spun to  
avoid any creasing. In  
this way ironing is  
easier. Furthermore the  
Easy Iron  
machine will perform  
After the programme  
has started, the time  
remaining is updated  
every minute.  
some additional rinses. This functxion can be  
used for cotton and synthetic.  
The Easy iron cannot be selected with Night  
Cycle option.  
2.05  
If you press this button, simultaneously for  
about 6 seconds, in combination with Extra  
Rinse" button, the child safety lock will be  
enabled (see Display paragraph).  
ATTENTION!  
When selecting the «proportional»  
programmes, the diplay shows the washing  
duration of the maximum recommended load.  
After the Start/Pause has been pressed, on  
the display appears an arrows animation  
indicating that the appliance is calculating the  
laundry amount and the real duration. During  
this time, the washing duration shown  
decreases.  
8 Select the Extra Rinse option  
This button can be  
selected with all  
programmes except  
Extra Rinse  
Wool, Hand wash, Mini  
30’, Duvet and Silk  
programmes. The  
machine performs some  
additional rinses.  
Lock  
This option is recommended for people who  
are allergic to detergents, and in areas where  
the water is very soft.  
Start/Pause  
If you press this button, simultaneously for  
about 6 seconds, in combination with "Easy  
Iron" button the child safety lock will be  
enabled (see Display paragraph).  
When the calculating phase has finished, the  
arrows animation desappears from the display  
and the washing time is adjusted to the real  
load.  
IMPORTANT!  
If an option is chosen that is not allowed with  
the selected programme, the red pilot light of  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
Operating sequence  
Washing programme phase icons  
Alarm codes  
By selecting the wash programme, the washing  
programme phase icons corresponding to the  
various phases making up the programme are  
shown in the bottom of the display.  
In the event of  
operating problems,  
some alarm codes can  
be displayed, for  
E20  
example E20 (see  
paragraph “Something not working”).  
2.05  
2.05  
Heating phase  
During the washing  
cycle the display shows  
a temperature icon  
illuminated to indicate  
that the appliance has  
After the machine has started, only the running  
icon stays on. When the programme has  
finished, a flashing zero «0.00» is displayed.  
2.05  
Delayed start  
started the heating phase of the water in the tub.  
Child safety lock enabled  
This device permits you to leave the appliance  
unsupervised without having the worry that  
children might be injured by or cause damage  
to the appliance.  
The selected delay (20 hours max) set by  
means of the relevant button appears on the  
display for about 3 seconds, then the duration  
of the previously selected programme is  
displayed.  
The delay time value  
decreases by one unit  
every hour and then,  
when 1 hours remain,  
15 h  
the time decreases every  
minute.  
Easy Iron  
Extra Rinse  
Incorrect option selection  
This function remains able also when the  
washing machine is not working.  
If an option which is not  
compatible with the set  
wash programme is  
There are two different ways to set this option:  
before pressing the Start/Pause: it will be  
impossible to start the machine.  
after pressing the Start/Pause: it will be  
impossible to change any other programme  
or option.  
selected, the message  
Err is displayed for about 2 seconds and the  
integrated red Start/Pause light start flashing.  
To enable or disable this option press  
simultaneously for about 6 seconds “Easy Iron”  
and “Extra Rinse” buttons until the icon  
appears or disappears on the display.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
Operating sequence  
10. Select the Start/Pause  
Before you start the programme, if you wish to  
delay the start, press repeatedly the «Delay  
To start the selected programme, press the  
Start/Pause button; the corresponding green  
pilot light stops flashing.  
Start» buttons  
desired delay.  
and  
, to select the  
The selected delay time value (up to 20 hours)  
will appear on the display for about 3 seconds,  
then the duration of the programme will appear  
again.  
The «Lock» light  
Lock  
illuminates to indicate  
that the appliance starts  
Start/Pause  
You must select this option after you have set  
the programme and before you press the  
Start/Pause button.  
operating and the door  
is locked.  
The wash programme can be delayed from 30  
min - 60 min - 90 min, 2 hours and then by 1  
hour up to a maximum of 20 hours by means  
of this button.  
The “Lock” light indicates if the door can be  
opened:  
light on: the door cannot be opened.  
The appliance is running.  
Selecting the delayed start:  
light off: the door can be opened.  
The washing programme is finished.  
To interrupt a programme which is running,  
depress the Start/Pause button: the  
corresponding green pilot light starts to flash.  
To restart the programme from the point at  
which it was interrupted, press the Start/Pause  
button again.  
Select the programme and the required  
options.  
Select the delay start.  
Depress “Start/Pause” button: the machine  
starts its hourly countdown.  
The programme will start after the selected  
delay has expired.  
If you have chosen a delayed start, the  
machine will begin the countdown.  
Cancelling the delayed start:  
You can cancel the delay time at any moment,  
before you press the Start/Pause button.  
If you have already pressed the Start/Pause  
button, and you wish to cancel the delay time,  
proceed as follows:  
IMPORTANT!  
If an incorrect option is selected, the red pilot  
light of the Start/ Pause button flashes for 3  
times and the message Err is displayed for  
about 2 seconds.  
• set the washing machine to PAUSE by  
pressing the Start/Pause button;  
11. Select the Delay Start  
• press the Delay Start buttons once until the  
symbol 0’ is displayed.  
Delay Start  
• press the Start/Pause button again to start  
the programme.  
90’  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
IMPORTANT!  
Opening the door after the programme has  
started  
First set the machine to pause by pressing the  
Start/Pause button.  
The door will be locked throughout the delay  
time. If you need to open the door, you must  
first set the washing machine to PAUSE by  
pressing the Start/Pause button, wait until the  
«Lock» pilot light goes off. After you have  
closed the door, press the Start/Pause button  
again.  
If the «Lock» light goes off, the door can be  
opened.  
If the «Lock» light does not switch off, this  
means that the machine is already heating,  
that the water level is above the bottom edge  
of the door or that the drum is turning.  
In this case the door can not be opened.  
If you cannot open the door but you need to  
open it you have to switch the machine off by  
turning the selector dial to «Off». After about 3  
minutes the door can be opened (pay attention  
to the water level and temperature!).  
Note!  
The Delay Start cannot be selected with  
Drain programme.  
Altering an option or a running programme  
It is possible to change any option before the  
programme carries it out.  
Before you make any change, you must pause  
the washing machine by pressing the  
Start/Pause button.  
At the end of the programme  
The machine stops automatically. The  
Start/Pause light goes off, the «Lock» light  
goes off and on the display will appear a  
flashing «0.00». The door can be opened.  
Changing a running programme is possible  
only by resetting it. Turn the programme  
selector dial to Off and then to the new  
programme position. Start the new programme  
by depressing the Start/Pause button again.  
If the  
«Rinse hold» or  
«Night Cycle»  
option has been selected, the «Lock» light  
remains alight and the door is locked to  
indicate that the water must be emptied out  
before opening the door.  
The display will show a flashing «0.00».  
To empty out the water please read the steps  
on the Rinse Hold option paragraph.  
The washing water in the tub will not emptied  
out.  
Interrupting a programme  
Depress the Start/Pause button to interrupt a  
programme which is running, the  
corresponding light starts to flash. Depress the  
button again to restart the programme.  
Turn the programme selector dial to «Off» to  
switch the machine off.  
Cancelling a programme  
Remove the laundry from the drum and  
carefully check that the drum is empty.  
If you do not intend to carry out another wash,  
close the water tap. Leave the door open to  
prevent the formation of mildew and  
unpleasant smells.  
Turn the selector dial to Off to cancel a  
programme which is running. Now you can  
select a new programme.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
Care and cleaning  
IMPORTANT!  
Remove the drawer by pressing the catch  
downwards and by pulling it out. Flush it out  
under a tap, to remove any traces of  
accumulated powder.  
You must DISCONNECT the appliance from  
the electricity supply, before you can carry out  
any cleaning or maintenance work.  
Cleaning the drawer recess  
Descaling  
The water we use normally contains lime. It is  
a good idea to periodically use a water  
softening powder in the machine. Do this  
separately from any laundry washing, and  
according to the softening powder  
Having removed the  
drawer, use a small  
brush to clean the  
recess, ensuring that all  
manufacturer's instructions. This will help to  
prevent the formation of lime deposits.  
washing powder  
residue is removed from  
the upper and lower  
Maintenance Wash  
part of the recess.  
With the use of low temperature washes it is  
possible to get a build up of residues inside the  
drum.  
We recommend that a maintenance wash be  
performed on a regular basis.  
Replace the drawer and run the rinse  
programme without any clothes in the drum.  
Cleaning the pump  
The pump should be inspected if  
To run a maintenance wash:  
the machine does not empty and/or spin  
the machine makes an unusual noise during  
draining due to objects such as safety pins,  
coins etc. blocking the pump.  
The drum should be empty of laundry.  
Select the hottest cotton wash programme.  
Use a normal measure of detergent, must be  
a powder with biological properties.  
Proceed as follows:  
Disconnect the appliance.  
If necessary wait until the water has cooled  
down.  
External cleaning  
Clean the exterior cabinet of the appliance with  
soap and water only, and then dry thoroughly.  
Open the pump door.  
Cleaning the dispenser drawer  
The washing powder and additive dispenser  
drawer should be cleaned regularly.  
Place a container close  
to the pump to collect  
any spillage.  
Pull out the emergency  
emptying hose, place it  
in the container and  
remove its cap.  
When no more water comes out, unscrew the  
pump cover and remove it. Always keep a  
rag nearby to dry up spillage of water when  
removing the cover.  
To aid cleaning, the top part of the additive  
compartment should be removed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
The dangers of freezing  
If the machine is exposed to temperatures  
below 0°C, certain precautions should be  
taken.  
Turn off the water tap.  
Unscrew the inlet hose.  
Place the end of the emergency emptying  
hose and that of the inlet hose in a bowl  
placed on the floor and let water drain out.  
Screw the water inlet hose back on and  
reposition the emergency emptying hose  
after having put the cap on again.  
When you intend to start the machine up  
again, make sure that the room temperature  
is above 0°C.  
Remove any objects from the pump impeller  
by rotating it.  
Put the cap back on the emergency emptying  
hose and place the latter back in its seat.  
Screw the pump cover  
fully in.  
Close the pump door.  
Emergency emptying out  
If the water is not discharged, proceed as  
follows to empty out the machine:  
pull out the plug from the power socket;  
close the water tap;  
if necessary, wait until the water has cooled  
down;  
IMPORTANT!  
When the appliance is in use and depending  
on the programme selected there can be hot  
water in the pump.  
Never remove the pump cover during a wash  
cycle, always wait until the appliance has  
finished the cycle, and is empty. When  
replacing the cover, ensure it is securely  
retightened so as to stop leaks and young  
children being able to remove it.  
Cleaning the water inlet filter  
If your water is very hard or contains traces of  
lime deposit, the water inlet filter may become  
clogged.  
It is therefore a good idea to clean it from time  
to time.  
open the pump door;  
place a bowl on the floor and place the end  
of the emergency emptying hose into the  
bowl. Remove its cap. The water should  
drain by gravity into the bowl. When the bowl  
is full, put the cap back on the hose. Empty  
the bowl. Repeat the procedure until water  
stops flowing out;  
clean the pump if necessary as previously  
described;  
replace the emergency emptying hose in its  
seat after having plugged it;  
screw the pump cover again and close the  
door.  
Turn off the water tap.  
Unscrew the water inlet  
hose. Clean the filter  
using a hard bristle  
brush. Tighten up the  
inlet hose.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
Something not working  
IMPORTANT!  
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily  
without calling out an engineer. Before contacting your local Service Centre, please carry out the  
checks listed below.  
During machine operation it is possible that the red Start/Pause pilot light flashes,one of the  
following alarm codes appears on the display and 3 acoustic signals sound every 20 seconds to  
indicate that the machine is not working.  
E10: problem with the water supply  
E20: problem with water draining  
E40: door open.  
Once the problem has been eliminated, press the Start/Pause button to restart the programme. If  
after all checks, the problem persists, contact your local Service Centre.  
Malfunction  
Possible Cause / Solution  
The door has not been closed. E40  
• Close firmly the door.  
The plug is not properly inserted in the power socket.  
• Insert the plug into the power socket.  
There is no power at the socket.  
• Please check your domestic electrical installation.  
The main fuse has blown.  
• Replace the fuse.  
The washing machine does not start:  
The selector dial is not correctly positioned and the  
Start/Pause button has not been depressed.  
• Please turn the selector dial and press the  
Start/Pause button again.  
The delay start has been selected.  
• If the laundry are to be washed immediately, cancel  
the delay start  
The water tap is closed. E10  
• Open the water tap.  
The inlet hose is squashed or kinked. E10  
• Check the inlet hose connection.  
The machine does not fill:  
The filter in the inlet hose is blocked. E10  
• Clean the water inlet hose filter.  
The door is not properly closed. E40  
• Close firmly the door.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
Malfunction  
Possible Cause / Solution  
The end of the drain hose is too low.  
• Refer to relevant paragraph in «water drainage»  
section.  
The machine fills then empties  
immediately:  
The drain hose is squashed or kinked. E20)  
• Check the drain hose connection.  
The drain pump is clogged. E20  
• Clean the drain pump.  
The machine does not empty and/or  
does not spin:  
The option  
or  
has been selected.  
• Select the Drain or Spin programmes  
The laundry is not evenly distributed in the drum.  
• Redistribute the laundry.  
Too much detergent or unsuitable detergent (creates  
too much foam) has been used.  
• Reduce the detergent quantity or use another one.  
Check whether there are any leaks from one of the  
inlet hose fittings. It is not always easy to see this as  
the water runs down the hose; check to see if it is  
damp.  
There is water on the floor:  
• Check the water inlet hose connection.  
The inlet hose is damaged.  
• Change it with a new one.  
The cap on the emergency emptying hose has not  
been replaced after cleaning the pump.  
Put the cap back on the emergency emptying and  
place the latter back in its seat.  
Too little detergent or unsuitable detergent has been  
used.  
• Increase the detergent quantity or use another one.  
Stubborn stains have not been treated prior to  
washing.  
• Use commercial products to treat the stubborn  
stains.  
Unsatisfactory washing results:  
The correct temperature was not selected.  
• Check if you have selected the correct  
temperature.  
Excessive laundry load.  
• Introduce into the drum less laundry.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
Malfunction  
Possible Cause / Solution  
The programme is still running.  
• Wait the end of washing cycle.  
The door lock has not been released.  
• Wait until the «Lock» light has gone out.  
The door will not open:  
There is water in the drum.  
• Select drain or spin programme to empty out the  
water.  
The transit bolts and packing have not been  
removed.  
• Check the correct installation of the appliance.  
The support feet have not been adjusted.  
• Check the correct levelling of the appliance.  
The machine vibrates or is noisy:  
The laundry is not evenly distributed in the drum.  
• Redistribute the laundry.  
Maybe there is very little laundry in the drum.  
• Load more laundry.  
The electronic unbalance detection device has cut in  
because the laundry is not evenly distributed in the  
drum. The laundry is redistributed by reverse rotation  
of the drum. This may happen several times before  
the unbalance disappears and normal spinning can  
resume. If, after 10 minutes, the laundry is still not  
evenly distributed in the drum, the machine will not  
spin. In this case, redistribute the load manually and  
select the spin programme.  
Spinning starts late or the machine  
does not spin:  
Redistribute the laundry.  
The machine is fitted with a type of motor which  
makes an unusual noise compared with other  
traditional motors. This new motor ensures a softer  
start and more even distribution of the laundry in the  
drum when spinning, as well as increased stability of  
the machine.  
The machine makes an unusual noise  
No water is visible in the drum  
Machines based on modern technology operate very  
economically using very little water without affecting  
performance.  
If you are unable to identify or solve the  
problem, contact our service centre.  
Before telephoning, make a note of the model,  
serial number and purchase date of your  
machine: the Service Centre will require this  
information.  
Mod. ... ... ...  
Prod. No. ... ... ...  
Ser. No. ... ... ...  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
Technical data  
Dimensions  
Width  
60 cm  
85 cm  
63 cm  
Height  
Depth (inclunding the porthole)  
Electrical connection Voltage -  
Overall power - Fuse  
Information on the electrical connection is given on the rating  
plate on the inner edge of the appliance door  
Water supply pressure  
Maximum Load  
Minimum  
Maximum  
0,05 MPa  
0,8 MPa  
Cotton  
Synthetics  
Delicates  
Woollens and handwash  
7.0 kg  
3.5 kg  
3.5 kg  
2.0 kg  
Spin Speed  
Maximum  
0
1600 rpm  
Consumption values  
Programmes  
Programme  
duration  
(in minutes)  
Energy  
consumption  
(in kWh)  
Water  
consumption  
(in litres)  
62  
2.1  
Cotton 95°C - Proportional  
Please refer  
to the display  
on the  
Cotton 60° Eco(*) - Proportional  
1.19  
52  
46  
control panel.  
0.9  
Synthetic 60°C - Proportional  
Infos  
The consumption data for the proportional programmes given on this chart is to be considered purely  
indicative and refers to the highest load size for each wash programme.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
Consumption values  
Energy  
consumption  
(in kWh)  
Water  
consumption  
(in litres)  
Programme  
duration  
Programme  
2.1  
62  
Cottons Normal 95°-  
2.3  
0.6  
74  
41  
54  
64  
42  
63  
Cottons Prewash 95°C -  
Cottons Superquick 95 -  
Synthetics Normal 60°C -  
0.9  
1.05  
0.4  
Synthetics Prewash 60°C -  
Synthetics Superquick 60°C-  
Delicates 40°C  
0.55  
0.25  
Mini 30’  
47  
75  
Duvet 30°C  
0.35  
0.25  
Silk 30°C  
50  
58  
58  
0.4  
0.4  
Handwash 40°C -  
Wool 40°C -  
Sport Shoes 40°C  
Sport 40°C  
0.5  
57  
70  
0.65  
Rinse  
Drain  
Spin  
0.1  
46  
-
-
-
-
(*) The “Cotton 60° Eco” is the reference  
programme for the data entered in the  
energy label, in compliance with EEC 92/75  
standards.  
Infos  
The consumption data shown on this chart is to  
be considered purely indicative, as it may vary  
depending on the quantity and type of laundry,  
on the inlet water temperature and on the  
ambient temperature. It refers to the highest  
temperature for each wash programme.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Installation instruction  
Unpacking  
All transit bolts and packing must be removed  
before using the appliance.  
5. Remove the bracket D, refit the six smaller  
bolts C and slide out the relevant plastic  
spacer E.  
You are advised to keep all transit devices so  
that they can be refitted if the machine ever  
has to be transported again.  
6. Open the porthole, take out the inlet hose  
from the drum and remove the polystyrene  
block fitted with the adhesive tape on the  
door seal.Open the porthole, take out the  
inlet hose from the drum and remove the  
polystyrene block fitted with the adhesive  
tape on the door seal.  
7. Fill the smaller upper hole and the two large  
ones with the corresponding plastic plug  
caps supplied in the bag containing the  
instruction booklet.  
1. After removing all the packaging, carefully  
lay machine on it’s back to remove the  
polystyrene base from the bottom.  
2. Remove the power supply cable and the  
draining hose from the hose holders on the  
rear of the appliance.  
Positioning  
A
Install the machine on a flat hard floor. Make  
sure that air circulation around the machine is  
not impeded by carpets, rugs etc. Check that  
the machine does not touch the wall or other  
kitchen units. Level the washing machine by  
raising or lowering the feet. The feet may be  
tight to adjust as they incorporate a self locking  
nut, but the machine MUST be level and  
stable.  
C
B
B
C
3. With a suitable spanner unscrew and  
remove the central rear bolt A.  
4. Unscrew and remove the two large rear  
bolts B and the six smaller bolts C.  
If necessary, check the setting with a spirit  
level.  
Any necessary adjustment can be made with a  
spanner.  
Accurate levelling prevents vibration, noise and  
displacement of the machine during  
operation.Never place cardboard, wood or  
similar materials under the machine to  
compensate for any unevenness in the floor.  
E
C
D
C
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
The appliance must be connected to a cold  
water supply.  
A minimum water pressure of 0.05 MPa (0.5  
bar) is required for safe operation of the  
appliance.  
If you cannot make the cold water connection  
direct from the rising mains, you may be able  
to operate the appliance from your cold water  
storage system.  
There should be a minimum distance of 5.02m  
(16.5 ft) between the appliance’s inlet and the  
bottom of the water storage tank.  
Water inlet  
An inlet hose is supplied and can been found  
inside the machine drum.  
Do not use the hose from your previous  
machine to connect to the water supply.  
Water drainage  
This appliance is designed to be permanently  
plumbed into your home's drainage system  
using one of the following methods.  
1. Open the porthole and extract the inlet  
hose.  
2. Connect the hose with the angled  
connection to the machine.  
Do not place the inlet hose downwards.  
Angle the hose to the left or right depending  
on the position of your water tap.  
1. Into a drainage standpipe.  
3. Set the hose  
correctly by loosening  
the ring nut.  
U” piece  
supplied  
After positioning the  
inlet hose, be sure to  
tighten the ring nut  
again to prevent leaks.  
Special  
Off  
Cottons  
S
p
o
r
t
4
0
°
95°  
3h  
6h  
9h  
S
p
o
r
t
S
h
o
e
s
4
0
°
60° Eco  
60°  
1000  
900  
Silk  
M
i
n
i
3
0
'
4
0
°
E
c
o
700  
Prewash  
Intensive  
Wash  
Door  
End  
Cold  
Hand  
40°  
Synthetics  
50°  
Super  
Quick  
Wash  
30°  
ool  
1
0
0
0
6
k
g
Options  
E
x
t
r
a
R
i
n
s
e
Start/Pause  
Spin  
W
40°  
aIron 40°  
Spin  
Drain  
40°  
R
i
n
s
e
3
0
°
ZWF10070W  
Delicates  
38 mm (11.2”)  
standpipe  
diameter  
4. Connect the hose to a tap with a 3/4” thread.  
Always use the hose supplied with the  
appliance. The inlet hose must not be  
lengthened. If it is too short and you do not  
wish to move the tap, you will have to  
purchase a new, longer hose specially  
designed for this type of use.  
Firstly form a hook in the end of the drain  
hose using the «U» piece supplied. Place the  
drain hose into your standpipe, which should  
have an internal diameter of approximately  
38mm thus ensuring there is an air break  
between the drain hose and standpipe.  
When discharging into a standpipe ensure that  
the top of the standpipe is no more than 90  
cm (35.4'') and no less than 60 cm (23.6'')  
above floor level.  
NOTE  
Installation should  
comply with local  
water authority and  
building regulations’  
requirements.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
Levelling  
Level the washing machine by raising or  
lowering the feet. The feet may be tight to  
adjust as they incorporate a self locking nut,  
but the machine MUST be level and stable.  
Special  
Spor  
t
40°  
Off  
95°  
Cottons  
3h  
6h  
9h  
Spor  
t
S
h
o
e
s
4
0
°
60° Eco  
60°  
1000  
900  
Silk  
Mini 30'  
Cold  
4
0
°
E
c
o
700  
Prewash  
Intensive  
Wash  
Door  
End  
40°  
Hand  
Synthetics  
50°  
Super  
Quick  
W
ash  
1
0
0
0
6
k
g
30°  
ool  
Spin  
Options  
E
x
t
r
a
R
i
n
s
e
Start/Pause  
W
40°  
Easy Iron 40°  
Spin  
Drain  
40°  
Rinse 30° Delicates  
ZWF10070W  
Any necessary  
adjustment can be  
made with a spanner.  
Accurate levelling  
prevents vibration,  
noise and  
displacement of the  
The drain hose may be extended to a  
maximum of 4 metres. An additional drain hose  
and joining piece is available from your local  
Service Force Centre. The joining piece must  
have an internal diameter of 18mm.  
machine during operation.  
Some vibration is inevitable, especially if  
mounted on a wooden floor.  
Sprung wooden floors are particularly  
susceptible to vibration. For advice, consult a  
builder. If possible, always place the machine  
on a solid floor.  
If your drain hose  
looks like this (see  
below) you do not  
require the «U» piece.  
Just push the hose  
firmly into the  
standpipe.  
Special conditions  
2. Onto a sink outlet spigot.  
If the outlet spigot has not been used before,  
remove any blanking plug that may be in place.  
If the floor is carpeted or covered with crumbly  
or soft material, insert a rigid support base  
under the feet to prevent noise, vibration or  
displacement. The base should protrude a few  
centimetres beyond the edges of the machine.  
WARNING!  
The machine should NOT be placed on deep  
pile carpeting.  
Loop  
NOTE  
Please ensure that when the appliance is  
installed it is easily accessible for the engineer  
in the event of a breakdown.  
Push the drain hose onto the spigot and secure  
with a clip if required, ensure a loop is formed  
in the drain hose (see diagram) to prevent  
waste from the sink entering the washing  
machine.  
In the interest of the environment  
Washing machines and dishwashers should be  
connected to the FOUL drainage system, the  
water will then be taken to a sewage works for  
treatment before being discharged safely into a  
river. It is essential that these appliances are  
not connected to the surface water drainage  
system as this water is discharged directly into  
a river or stream and may cause pollution.  
Important!  
Before connecting the machine to new  
pipework or to pipework that has not been  
used for some time, run off a reasonable  
amount of water to flush out any debris that  
may have collected in the pipes.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30  
If you require any further advice please  
contact your local water authority.  
The wires in the mains lead are coloured in  
accordance with the following code:  
Green and Yellow ..............................- Earth  
Blue ....................................................- Neutral  
Brown..................................................- Live  
The wire coloured green  
GREEN &YELLOW  
SHOWER  
and yellow must be  
connected to the  
E
SINK TOILET  
BATH  
BIDET  
terminal marked with  
L
N
the letter «E» or by the  
WASHING  
MACHINE  
DISHWASHER  
earth symbol  
or  
RAINWATER  
'RUN-OFF'  
BROWN  
coloured green and  
yellow.  
BLUE  
FOUL DRAIN  
CORD CLAMP  
SURFACE WATER  
SEWERS  
FOUL SEWERS  
DRAINS  
&
SEWAGE  
TREATMENT  
WORKS  
UNTREATED  
DISCHARGE  
The wire coloured blue must be connected to  
the terminal marked «N» or coloured black.  
TREATED  
DISCHARGE  
RIVER  
RIVER  
The wire coloured brown must be connected to  
the terminal marked «L» or coloured red.  
Upon completion there must be no cut, or stray  
strands of wire present and the cord clamp  
must be secure over the outer sheath.  
Electrical connection  
Any electrical work required to install this  
appliance should be carried out by a qualified  
electrician or competent person.  
WARNING!  
WARNING!  
A cut off plug inserted into a 13 amp socket  
is a serious safety (shock) hazard.  
Ensure that the cut off plug is disposed of  
safely. Should the appliance power supply  
cable need to be replaced, this must be  
carried out by our Service Force Centre.  
This appliance must be earthed.  
The manufacturer declines any liability  
should this safety measure not be  
observed.  
Before switching on, make sure the electricity  
supply voltage is the same as that indicated  
on the appliance’s rating plate.  
The power supply cable must be easily  
accessible after installing the appliance.  
IMPORTANT!  
Permanent connection  
Information on the electrical connection is  
given on the rating plate on the inner edge  
of the appliance door.  
In the case of permanent connection it is  
necessary that you install a double pole switch  
between the appliance and the electricity  
supply (mains), with a minimum gap of 3mm  
between the switch contacts and of a type  
suitable for the required load in compliance  
with the current electrical regulations.  
The switch must not break the yellow and  
green earth cable at any point.  
The appliance is supplied with a 13amp plug  
fitted. In the event of having to change the  
fuse in the plug supplied, a 13amp ASTA  
approved (BS1363/A) fuse must be used.  
Should the plug need to be replaced for any  
reason, proceed as described below.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
Environmental concerns  
Packaging materials  
Ecological hints  
The materials marked with the symbol  
recyclable.  
>PE<=polyethylene  
>PS<=polystyrene  
>PP<=polypropylene  
This means that they can be recycled by  
disposing of them properly in appropriate  
collection containers.  
are  
To save water, energy and to help protect the  
environment, we recommend that you follow  
these tips:  
Normally soiled laundry may be washed  
without prewashing in order to save  
detergent, water and time (the environment  
is protected too!).  
The machine works more economically if it is  
fully loaded.  
Old machine  
Use authorised disposal sites for your old  
appliance. Help to keep your country tidy!  
With adequate pre-treatment, stains and  
limited soiling can be removed; the laundry  
can then be washed at a lower temperature.  
Measure out detergent according to the  
water hardness, the degree of soiling and  
the quantity of laundry being washed.  
The symbol  
on the product or on its  
packaging indicates that this product may not  
be treated as household waste. Instead it shall  
be handed over to the applicable collection  
point for the recycling of electrical and  
electronic equipment. By ensuring this product  
is disposed of correctly, you will help prevent  
potential negative consequences for the  
environment and human health, which could  
otherwise be caused by inappropriate waste  
handling of this product. For more detailed  
information about recycling of this product,  
please contact your local city office, your  
household waste disposal service or the shop  
where you purchased the product.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32  
Guarantee conditions  
Standard guarantee conditions  
Service and Spare Parts.  
We, Zanussi-Electrolux, undertake that if  
within12 months of the date of the purchase  
this Zanussi-Electrolux appliance or any part  
thereof is proved to be defective by reason  
only of faulty workmanship or materials, we  
will, at our option repair or replace the same  
FREE OFCHARGE for labour, materials or  
carriage on condition that:  
In the event of your appliance requiring  
service, or if you wish to purchase spare parts,  
please contact your local Service Force Centre  
by telephoning:  
0870 5 929 929  
Your telephone call will be automatically routed  
to the Service Force Centre covering your  
postcode area. For the address of your local  
Service Force Centre and further information  
about Service Force, please visit the website at  
The appliance has been correctly  
installedand used only on the electricity  
supply statedon the rating plate.  
The appliance has been used for normal  
domestic purposes only, and in accordance  
with the manufacturer's instructions.  
The appliance has not been serviced,  
maintained, repaired, taken apart or  
tampered with by any person not authorised  
by us.  
Before calling out an engineer, please ensure  
you have read the details under the heading  
«Something not working». When you contact  
the Service Force Centre you will need to give  
the following details:  
1 Your name, address and postcode.  
2 Your telephone number.  
Electrolux Service Force Centre must  
undertake all service work under this  
guarantee.  
3 Clear concise details of the fault.  
Any appliance or defective part replaced  
shall become the Company's property.  
This guarantee is in addition to your  
statutoryand other legal rights.  
4 The model and Serial number of the  
appliance (found on the rating plate).  
5 The purchase date.  
Please note a valid purchase receipt or  
guarantee documentation is required for in  
guarantee service calls.  
Exclusions  
Damage or calls resulting fromtransportation,  
improper use or neglect, thereplacement of  
any light bulbs or removableparts of glass or  
plastic.  
Costs incurred for calls to put right an  
appliance which is improperly installed or  
calls to appliances outside the United  
Kingdom.  
Customer Care  
For general enquiries concerning your  
Electrolux appliance, or for further information  
on Electrolux products please contact our  
Customer Care Department by letter or  
telephone at the address below or visit our  
Appliances found to be in use within  
acommercial environment, plus those which  
are subject to rental agreements.  
Products of Electrolux manufacturer that are  
not marketed by Electrolux.  
Customer Care Department Electrolux Major  
Appliances Addington Way Luton Bedfordshire,  
LU4 9QQ Tel: 08705 727 727 (*)  
(*) Calls may be recorded for training purposes  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
For Customer Service in The Republic of  
Ireland please contact us at the address below:  
Electrolux Group (Irl) Ltd  
Long Mile Road, Dublin 12, Republic of Ireland  
Tel: + 353 (0)1 4090751  
European guarantee  
This appliance is guaranteed by Electrolux, in  
each of the countries listed in the following  
page, for the period specified in the appliance  
guarantee or otherwise by law. If you move  
from one of these countries to another of these  
countries the appliance guarantee will move  
with you subject to the following qualifications:  
The appliance guarantee starts from the  
date you first purchased the appliance  
which will be evidenced by production of a  
valid purchase document issued by seller  
of the appliance.  
The appliance guarantee is for the same  
period and to the same extent for labour  
and parts as exists in your country of  
residence for this particular model or range  
of appliances.  
The appliance guarantee is personal to the  
original purchaser of the appliance and  
cannot be transferred to another user.  
The appliance is installed and used in  
accordance with instructions issued by  
Electrolux and is only used within the  
home, i.e. is not used for commercial  
purposes.  
The appliance is installed in accordance  
with all relevant regulations in force within  
your new country of residence.  
The provisions of this European Guarantee do  
not affect any of the rights granted to you by  
law.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
34  
à
Albania  
+35 5 4 261 450  
+32 2 363 04 44  
+420 2 61 12 61 12  
+45 70 11 74 00  
+49 180 32 26 622  
+37 2 66 50 030  
+34 902 11 63 88  
+44 8705 929 929  
+30 23 10 56 19 70  
+38 51 63 23 338  
+353 1 40 90 753  
+39 (0) 434 558500  
+37 17 84 59 34  
+370 5 27 80 609  
+35 2 42 43 13 01  
+36 1 252 1773  
Rr. Pjeter Bogdani Nr. 7 Tirane  
Belgique/België/Belgien  
Česká republika  
Danmark  
Bergensesteenweg 719, 1502 Lembeek  
Budějovická 3, Praha 4, 140 21  
Sjællandsgade 2, 7000 Fredericia  
Deutschland  
Muggenhofer Str. 135, 90429 Nürnberg  
Mustamäe tee 24, 10621 Tallinn  
Eesti  
España  
Carretera M-300, Km. 29,900 Alcalá de Henares Madrid  
France  
Great Britain  
Hellas  
Addington Way, Luton, Bedfordshire LU4 9QQ  
4, Limnou Str., 54627 Thessaloniki  
Hrvatska  
Ireland  
Slavonska avenija 3, 10000 Zagreb  
Longmile Road Dublin 12  
Italia  
C.so Lino Zanussi, 26 - 33080 Porcia (PN)  
Kr. Barona iela 130/2, LV-1012, Riga  
Verkiu,2 9, 09108 Vilnius, Lithuania  
Rue de Bitbourg, 7, L-1273 Hamm  
Latvija  
Lituania  
Luxembourg  
Magyarország  
Nederland  
Norge  
H-1142 Budapest XIV, Erzsébet királyné útja 87  
Vennootsweg 1, 2404 CG - Alphen aan den Rijn  
Risløkkvn. 2 , 0508 Oslo  
+31 17 24 68 300  
+47 81 5 30 222  
+43 18 66 400  
Österreich  
Polska  
Herziggasse 9, 1230 Wien  
+48 22 43 47 300  
+35 12 14 40 39 39  
+40 21 451 20 30  
ul. Kolejowa 5/7, Warsaw  
Portugal  
Romania  
Quinta da Fonte - Edificio Gonçalves Zarco - Q35 -2774-518 Paço de Arcos  
Str. Garii Progresului 2, S4, 040671 RO  
Industriestrasse 10, CH-5506 Mägenwil  
Tr aška 132, 1000 Ljubljana  
Schweiz-Suisse-Svizzera +41 62 88 99 111  
Slovenija  
Slovensko  
Suomi  
+38 61 24 25 731  
+421 2 43 33 43 22  
Electrolux Slovakia s.r.o., Electrolux Domáce spotrebiče SK, Seberíniho 1, 821 03 Bratislava  
Sverige  
Türkiye  
+46 (0)771 76 76 76  
+90 21 22 93 10 25  
+7 095 937 7837  
Electrolux Service, S:t Göransgatan 143, S-105 45 Stockholm  
Tarlabași caddesi no : 35 Taksim Istanbul  
Россия  
129090 Москва, Олимпийский проспект, 16, БЦ “Олимпик”  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Subject to change without notice  
132973870  

Whirlpool Toaster MWD 207 User Manual
Whirlpool Ventilation Hood GZ7730XGS0 User Manual
White Rodgers Universal Remote 5059 User Manual
Whynter Dehumidifier RPD 302W User Manual
Worksaver Compact Loader JDBS 412 User Manual
Worksaver Lawn Mower PLR 48, PLR 72, PLR 60, PBX 42 User Manual
Wright Manufacturing Lawn Mower 43181 User Manual
Xilinx Switch ML403 User Manual
Zanussi Freezer ZV 45 R User Manual
Zanussi Washer TLE 1116 W User Manual