TUMBLE DRYER
ZDC 5375 W
Reset/
Off
2
y
M
e
m
1
o
r
M
e
m
o
r
y
Ready to wear
Store dry
Cooling
30 min
60 min
Slightly damp
Start/
Pause
Door
Spin
Option
Change
Exit
Iron dry
achine iron dry
TIMELINE
A
U
T
O
R
E
V
E
R
S
E
6
k
g
Iron dry
Store dry
Z
D
C
5375W
Unpacking: see page 23
INSTRUCTION BOOKLET
GB
125981241
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Something Not Working
Service and Spare Parts
Customer Care
18
19
19
20
For the User
Important Safety Information
2
• Installation
• Child Safety
• Use
Guarantee Conditions
For the Installer
Your New Tumble Dryer
Description of the Appliance
The Control Panel
4
4
5
Installation Instructions
21
21
22
Technical Specifications
• Programme/Time Selector Dial
• Display
• Door Release Button
• Spin Speed Button
• Option, Change, Exit Button
• Start/Pause Button
5
5
Adjusting the Level of Conductivity
• Unpacking
• Positioning
• Stacking kit (optional accessory)
• Door reversal
• Electrical connection
23
23
5-6
6
23
6-9
10
23
23-24
Programme Chart
11
12-14
15
Operating Sequence
Hints & Tips on Drying
Maintenance and Cleaning
16
• External cleaning
• Cleaning the door
16
16
• Cleaning the filters
16
• Cleaning the condenser unit
• Emptying the water reservoir
• Cleaning the drum
16-17
17
17
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Your New Tumble Dryer
This tumble dryer will give your wash that soft, relaxed feel whatever the weather.
Extremely high quality standards both during development and
manufacturing guarantee a long service life for your appliance.
Maximum economy in the operation of your dryer is achieved through
very economical electricity consumption and short drying times.
Energy saving tips
• When the appliance is to be scrapped, cut off the
power supply cable and make the door closing
device unusable to prevent young children from
being trapped inside.
To save energy we recommend that you follow these
hints:
• Try to load the maximum capacity of the machine
• Help to keep your country tidy - use authorised
disposal sites for your old appliance.
as small loads are uneconomical.
• Always load well spun laundry. The higher the spin
speed, the lower the electricity consumption and
the shorter the drying times.
How do we help to protect the
environment? We use recycled paper!
• Do not over-dry laundry, this avoids creasing and
saves energy.
•
Old appliance
• Clean the filters regularly to avoid excessive drying
times and high electricity consumption.
The symbol
on the product or on its packaging
• Ventilate the room well. The room temperature
should not exceed +35°C during drying.
indicates that this product may not be treated as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by in appropriate
waste handling of this product. For more detailed
In the interest
of the environment
• Materials marked with the symbol
• Check with your local Council or Environmental
Health Office to see if there are facilities in your
area for re-cycling this appliance.
are recyclable.
information about recycling of this product, please contact
your local city office, your household waste disposal
service or the shop where you purchased the product.
Description of the Appliance
01 Control panel
02 Water reservoir
1
r
t/
e
Sta
R
ese
ra
ext
d
ry
P
aus
t/
Off
ton
Cot
Exit
r
w
ea
2
dy
Rea
t
o
ge
Chan
o
r
y
e
m
1
M
on
Opti
re
d
ry
o
r
y
Sto
M
e
m
S
pi
n
5
W
p
r
C
ZD
53
5
dam
D
oo
htly
Slig
ling
Coo
dry
30
min
Iron
d
ry
e
ir
on
chin
60
mi
n
Ma
dry
tic
the
Syn
ry
e
xtra
B
aby
03 Fluff filters
d
dry
re
Sto
Iron
k
g
6
R
S
E
V
E
R
E
T
O
A
U
I
N
E
E
L
T
I
M
04 Rating Plate
05 Condenser unit
06 Adjustable feet
3
2
4
3
6
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
The Control Panel
Reset/
Off
2
Memory
1
Memory
Ready to wear
Store dry
Cooling
30 min
60 min
Slightly damp
Start/
Pause
Door
Spin
Option
Change
Exit
Iron dry
Machine iron dry
TIMELINE
AUTOREVERSE
6
kg
Iron dry
Store dry
ZDC 5375W
1
2 3
4
5
6
2
Display
1
Programme/Time
Selector Dial
The DISPLAY is used for setting a large number of
functions and combine them with each other using
only a few control elements (1 programme selector
dial and 6 buttons). This simple control method is
made easy thanks to the interactive display.
Allows you to select electronically controlled or time
controlled drying.
Turn the dial to the required programme or time.
Interactive means that the dryer display changes to
reflect each step you have entered. This ensures that
only those settings that make sense are made. You are
able to see the current settings at any time in the
information panel and in the option row.
The selector dial can be turned either clockwise or
counterclockwise.
Electronically controlled drying (automatic)
The appliance runs these programmes with the help
of probes which detect the degree of dampness of the
laundry.
Simply select the programme according to the type of
laundry and degree of drying required.
1
3
2
Cotton extra
Drying
08.30
10.55
1200
Time controlled drying
Door
Spin
Options
Change
Exit
This can be used to finish off drying if necessary.
Select the 60 minute programme for cottons or the 30
minute programme for synthetics.
4
To cancel a programme which is running, turn the
programme selector dial to “RESET/OFF”.
1. Information panel shows the current settings and
the current phase of drying cycle.
At the end of drying, turn the selector dial to
“RESET/OFF” to switch the machine off before
removing the laundry.
2. Real time clock
3. End cycle time
The selector dial is divided into 4 sections:
● Cotton (blue section)
4. Selection shows the spin speed of your washing
machine and the options selected.
● Synthetics (green section)
● Time controlled drying (grey section)
● Memory 1, Memory 2 (green section)
3
DOOR RELEASE Button
Press this button to open the door.
The icon appears above the relative button.
Reset/
Off
2
If the door is opened while the programme is running
the appliance immediately stops drying. The «Pause»
Memory
1
Cotton extra dry
Ready to wear
Memory
Cooling
Store dry
message appears on the display, the
icon is
Slightly damp
30 min
60 min
shown above the Door button and the START/
PAUSE button starts flashing.
Opening the door by means of this button is
possible only if the tumble dryer is on
(programme selector dial set to a programme or
drying time).
Iron dry
Machine iron dry
Baby
Iron dry
Synthetic extra dry
Store dry
5
Download from Www.Somanuals.com. All Manuals Search And Download.
If you open the door during a programme, in order to
restart the programme you must press the Start/Pause
button again after having closed the door. The
icon appears on the display above the relative door
button.
Change button allows you to select/change the status
of the different icons.
Half Power
Yes
10.55
Door
Spin
Options
Change
Exit
4SPIN SPEED Button
Press this button repeatedly until the value shown on
the display matches the speed the laundry items were
originally spun in your washing machine.
Depending on the type of laundry the spin speeds are
the following:
Exit button allows you to return to the previous
selection.
- COTTONS: ........800-900-1000-1100-1200-1300
1400 1500-1600 rpm.
Cotton extra
Cycle end at
08.30
10.55
- SYNTHETICS: ..800-900-1000 rpm.
1200
- JUMPERS (BABY DRY): 800-900-1000-1100-1200 rpm.
Door
Spin
Options
Change
Exit
If you do not know the exact laundry spin speed you
can choose blank (no value on the display). The
tumble dryer will dry the laundry using a default
factory drying cycle.
Using this option you could decrease the drying cycle
time, saving energy.
Depending on the programme, different functions can
be combined. These must be selected after choosing
the desired programme and before pressing the
START/PAUSE button.
By depressing the «Option» button, all the symbol
icons, allowed for the selected programme, will
appear in the display.
If you have selected a time controlled programme
(60 min. or 30 min.) you could not use this option
because it has been selected a fixed time of drying.
If you try to press this button a warning message
«Selection error» appears in the display.
The first option
(Half Power) will start flashing.
Its name and status will appear on the display.
If you want to change the option status, press
«Change» button. A line will appear below the
selected icon, indicating that the option is set.
To select the other options press again the «Option»
button and proceed as before.
5 OPTION, CHANGE and
EXIT Buttons
Option button allows you to move through the
option icons.
Once you have completed the selection of the options,
press the «Exit» button, the selected icons will remain
fixed on the display.
Half Power
No
10.55
Door
Spin
Options
Change
Exit
Note: To modify the already chosen option selections,
repeat the previous procedure.
Half Power
Selecting this option allows drying to be performed at
a lower temperature, for delicate items.
The corresponding
icon appears on the display
during set up mode and the drying cycle.
A dash is shown under the relative icon to indicate
that the option has been selected.
This option can also be used for time controlled
drying.
This option cannot be selected with Quick Dry
.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
by the programme selected.
Quick
This option will decrease the duration of the drying
phase and it allows you to save energy.
This option cannot be selected with time controlled
dying (30 min. and 60 min.).
By selecting this option the drying time is reduced in
the following COTTON programmes:
● EXTRA DRY
● READY TO WEAR
Long Anticrease
● STORE DRY
This option cannot be selected with Half Power
To be used when you are not able to remove your
dried laundry just after the end of the drying cycle.
and Dry Level
option.
Selecting this option the anticrease phase will be
prolonged by an hour.
Delay Start
This option makes it possible to delay the starting of
the drying programme by 30 min - 60 min - 90 min, 2
hours and then by 1 hour till 20 hours. You can
modify the status of the delay pressing the «Change»
button sequentially. The delay you have selected is
indicated in the display.
Dry Level
Selecting Dry Level option, you can choose 3
different degrees of humidity that your laundry
retains.
To select the requested humidity degree press the
«Change» button repeatedly.
When on the display appears:
Delay Start
Start in 30 min.
9.42
12.15
Increased Dry
1200
Door
Spin
Options
Change
Exit
You have chosen the medium degree of drying.
Drying cycle time will increase by approx. 3
min.
Very Dry
Provides the highest degree of drying. Drying
cycle time will increase by approx. 6 min.
You must select this option after you have set the
programme and before you press the START/PAUSE
button.
Reduced Dry
Provides the lowest degree of drying. Drying
cycle time will decrease by approx. 2 min.
To confirm your choice press «Exit».
This option cannot be selected with Quick option
You can cancel the delay time at any moment, before
you press the START/PAUSE button. If you have
already pressed the START/PAUSE button and you
wish to cancel the delay time proceed as follows:
.
1. set the dryer to PAUSE by pressing the
START/PAUSE button;
2. deselect the Delay start option, changing the
status;
3. press the START/PAUSE button to start the
programme.
No Buzzer
A buzzer sounds:
● when selecting the programme
● when an incorrect option selection is made
● when the programme selector dial is turned to
another position during the programme or when
you press an option button during the cycle
Important!
The selected delay can be changed only after selecting
the drying programme again.
If you wish to load other laundry to be dried after
having selected the delay time option:
- open the door, pressing the relative button
- load your laundry
● at the end of the programme
● when the water reservoir is full
● if the machine is not working correctly
● when the small door at the bottom is open.
By selecting this option, pressing «Change» button,
the acoustic signal is switched off:
- press the START/ PAUSE button, after having
closed the door.
● at the end of the programme
Half Load
● when the water reservoir is full
This option can be selected when the load inside the
drum is less or equal to the half load weight declared
● if the machine is not working correctly
● when the small door at the bottom is open.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
To confirm this option press «Exit» button.
Set Up menu:
To change the memorised programme setting repeat
the procedure from the beginning.
Sound
Menu option is used for selecting various basic
settings without affecting the particular drying
programme. These basic settings will remain active
until they are deselected/modified.
The sound setting permits you to modify the volume
of the sound emitter. You can choose between
different levels: low, no sound and normal.
Example:
To move through the different Menu settings use the
«Option» button. To change/confirm the selected
setting use the «Change» button.
1. Enter the Menu option and select the sound setting.
Memory
Sound
Programme settings that are frequently used can be
saved. There are 2 memory spaces available for this
purpose. The saved programme can be selected in the
same way as any other drying programme by means
of the selector dial.
Normal
Temp.
Spin
Options
Change
Exit
Example: Cotton Extra Dry, 1200 rpm, No Buzzer
and Dry Level option).
2. Use the «Change» button to select the desired
level.
1. Select the cycle and programme settings.
Reset/
Off
2
Memory
1
Cotton extra dry
Ready to wear
Memory
Cotton extra
Cycle end at
08.30
10.55
Sound
Low or No Sound
Cooling
Store dry
1200
Slightly damp
30 min
60 min
Door
Spin
Options
Change
Options
Change
Exit
Temp.
Spin
Exit
Iron dry
Machine iron dry
Baby
Iron dry
Synthetic extra dry
Store dry
2. Enter the Menu option and select one of the
memory positions. «Store programme?»
message will appear in the display.
Water Hardness
You can change the water hardness choosing 3
different degrees (see the chapter «Adjusting the level
of conductivity» on page 22).
A
B
Setup
Memory 1
Store programme?
Language
You can change the language setting if you would like
the indicators in the display to appear in a different
language.
Temp.
Spin
Options
Change
Temp.
Spin
Options
Change
Exit
Exit
A
B
3. To memorise the selected programme press the
«Change» button. «Stored» message will appear
in the display.
Programme Stored
Temp.
Spin
Options
Change
Exit
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Example:
Brightness
1. Enter the Menu option and select the Language
setting.
The Brightness setting allows you to modify the
backlight intensity of the display.
Example:
1. Enter the Menu option and select the Brightness
setting.
Language
ENGLISH
2. Use the «Change» button to set up the desired
brightness level.
Temp.
Spin
Options
Change
Exit
Brightness
Brightness
Temp.
Spin
Options
Change
Temp.
Spin
Options
Change
Exit
Exit
2. Press the «Change» button to select the desired
Language.
A
B
Einstellungen
Sprache
DEUTCH
Note:
Temp.
Spin
Options
Change
Temp.
Spin
Options
Change
Exit
Exit
At the end of the programme if no button is pressed
for approximately 10 minutes the backlight intensity
goes off.
B
A
Clock
The clock setting permits you to modify/set up the
current time. It is important to keep it updated as the
current END Cycle Time depends on it.
Example:
1. Enter the Menu option and select the Clock
setting.
2. With a short/single time press of the «Change»
button, the time varies minute by minute. With a
continue pressure of the «Change» button, the
time varies 10 minutes by 10 minutes.
Contrast
The Contrast setting allows you to modify the optical
characteristic of the display.
Example:
1. Enter the Menu option and select the Contrast
setting.
2. Use the «Change» button to set up the desired
contrast level.
Contrast
Contrast
Temp.
Spin
Options
Change
Temp.
Spin
Options
Change
Exit
Exit
A
B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6START/PAUSE Button
Start/
Pause
This button has 2 functions:
● Start: after you have selected the desired
programme and options, press this button to start
the tumble dryer. The light close to the button will
stop flashing and remain lit.
If you have selected a delay time option, the
countdown will begin and will be shown on the
display.
● Pause: when you press this button again, the
programme in progress is interrupted. The light
close to the button will start flashing. To restart
the programme, press the button again.
If the door is opened while the programme is running
the appliance immediately stops drying. The «Pause»
message appears in the display and the
shown above the Door button.
icon is
The appliance immediately stops drying, the «Pause»
and «Please close condenser door» messages appear
in the display also when the condenser door is
opened.
This button must be pressed again after closing the
door in order to restart the programme from the point
at which it was interrupted.
This button must also be pressed after a power
failure and after having re-inserted the water
reservoir.
If it has been emptied in the middle of a
programme after«The tank is full, please empty»
message and an acoustic signal has sounded.
In both cases the light of the Start/Pause button
flashes to remind you that the start button needs to be
pressed again.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme Chart
Automatic drying (electronic programmes)
Type of laundry
Degree of drying required
Max-load (1)
Programme
Extra dry
Ready to wear
Store dry
Slightly damp
Iron dry
Machine Iron Dry
6 kg
6 kg
6 kg
6 kg
6 kg
6 kg
Extra dry (COTTON EXTRA)
Ready to wear (COTTON STRONG)
Store dry(*) (COTTON CUPBOARD)
Slightly damp (COTTON DAMP)
Iron dry(*) (COTTON IRON)
COTTON
Machine Iron Dry (COT. MACHINE IRON)
Extra dry
Store dry
Iron dry
Extra dry (EASYCARE EXTRA)
Store dry(*) (EASYCARE CUPBOARD)
Iron dry (EASYCARE IRON)
3 kg
3 kg
3 kg
SYNTHETIC
JUMPERS
1 kg
(10 jumpers)
Baby dry (BABY)
Baby dry
(*) According to IEC 61121 Standards.
• Baby Dry cycle is a special programme for jumpers to be dried “READY TO WEAR”.
Time controlled drying
Type of laundry
Programme
selector dial position
Drying time
Max-load (1)
60 min
30 min
COTTON
6,5 kg
3 kg
60’
30’
SYNTHETIC
(1) Never overfill the drum (do not load large quilts, for example).
Drying times vary according to:
• The type of laundry
• The size of the load
• The degree of spinning prior to drying.
• The degree of dryness required
Cooling
This position on the programme selector dial can be used to freshen the laundry (e.g. to remove a persistent
odour of moth-balls).
Load
It is often difficult to estimate the weight of items to be dried. We therefore recommend that you adopt the
following guidelines:
• cotton, linen: drum full but not too tightly packed;
• synthetics: drum no more than half full;
• delicate fabrics: drum no more than one third full.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Sequence
Example:
Before using your tumble dryer for the first time, we
recommend to place a few damp cloths inside the
appliance and dry for 30 minutes.
Press the «Change» button until the desired
language appears in the display.
There may be dust inside a brand new tumble dryer.
Language
ENGLISH
Sprache
DEUTCH
Drying
Temp.
Spin
Options
Change
Temp.
Spin
Options
Change
Exit
Exit
1. Connect the appliance.
2. Open the door (see picture).
A
Press the EXIT button to confirm the selection.
Einstellungen
P1149
P1108
Temp.
Spin
Options
Change
Exit
3. Load the items one at a time, shaking them out
B
loosely.
4. Close the door. Please check the laundry does not
get caught between the door and filter.
All indicators on the display will appear in this
language from now on.
Note:
If the undesired language has been set, press the
«Spin and Option» buttons simultaneously for
about 3 seconds in order to change the language.
Follow the instructions as before.
5. Turn the selector dial to the desired programme to
switch the appliance on. To switch the appliance
off turn it to «Reset/Off».
Reset/
Off
2
Memory
1
Cotton extra dry
Ready to wear
Memory
Cooling
Store dry
Setting the time
Slightly damp
30 min
60 min
You should set the time prior to the first drying
cycle and when changing to and from daylight
savings time. See «Clock setting», Menu.
Iron dry
Machine iron dry
Baby
Iron dry
Synthetic extra dry
Store dry
6. Turn the selector dial, in order to select the
desired programme. The relevant message will
appear in the display.
Switching on the appliance for the first time.
Language
When switching on the appliance for the first time
you must set the language in which you want the
indicators on the display to appear.
The display will show the end cycle time «Cycle
end at» of the selected programme, calculated on
the basis of the maximum load for each type of
fabric. The START/PAUSE button light will start
flashing.
If the load of laundry to be dried is small, at the
beginning of the cycle the display will still
indicate the end cycle relevant to the maximum
load.
Important!
If the display is not showing any language, the
appliance has already been switched on once. In
such case, go to the chapter «Change language» if
you would like to change the language setting.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The duration value will be gradually adjusted
during the execution of the drying cycle.
10.Press the START/PAUSE button. The relevant
light will stop flashing. The message relevant to
the phase that is in progress will be shown in the
display.
Reset/
Off
2
Memory
1
Cotton extra dry
Ready to wear
If you have chosen a delayed start, the tumble
dryer will begin the countdown.
Memory
Cotton extra
Cycle end at
08.30
10.55
Cooling
Store dry
1200
Slightly damp
30 min
60 min
Door
Spin
Options
Change
Exit
Iron dry
Machine iron dry
Baby
Iron dry
Start/
Pause
Synthetic extra dry
Store dry
Cotton extra
Drying
08.30
10.55
1200
Door
Spin
Options
Change
Exit
7. Press the SPIN button repeatedly, in order to
select the real spin speed that your laundry has
been spun. The selected spin level will be shown
on the third row above to the spin button.
If the programme selector dial is turned to another
position, when the machine is running, the buzzer
will sound and the «Selection error» message
appears in the display.
Cotton extra
Cycle end at
08.30
10.55
1200
The drum turns alternately in both directions
during drying.
Door
Spin
Options
Change
Exit
All drying programmes end with a 10 minute
cooling phase (on the second row of the display
appears the «Cooling» message).
You may remove the laundry after this phase.
8. Press the «Options» button to select the required
options.
The display shows the following messages one
after an other: «Please clean the filters» and
«Please empty the tank». The buzzer sounds to
indicate the end of the cycle.
To confirm your choice press the «Change»
button.
11. If the laundry is not removed at the end of the
cycle, the dryer performs an anti-creasing phase
(duration: 30 minutes maximum).
Depending on the selected programme only
certain options are available and shown during
the selection phase.
Note: Not all the options are compatible
between themselves. The incompatible option
icons will disappear.
If you do not remove the laundry, the dryer will
stop automatically at the end of the anti-creasing
phase. The display will show the following
messages one after an other: «Anticrease»,
«Please clean the filters» and «Please empty the
tank». The buzzer sounds to indicate the end of
the cycle.
9. Select the DELAY START option if required.
Before you start the programme choose the
required option.
The selected delay time value (up to 20 hours)
will appear on the display while selecting.
The end cycle will be updated and shown on the
relative position of the display.
The light of the START/PAUSE button goes off
and a flashing zero appears on the display.
12.Turn the programme selector dial to “RESET/
OFF”; all the lights go out. The appliance is
switched off.
Remove the laundry.
Delay Start
No
Delay Start
Start in 30 min
10.55
11.25
If you open and then close the door before
turning the programme selector dial to
“RESET/OFF”, the machine is ready to
perform another drying programme. The
display shows the selected programme,
duration of the programme and the options
required.
Door
Spin
Options
Change
Door
Spin
Options
Change
Exit
Exit
13
Download from Www.Somanuals.com. All Manuals Search And Download.
After each use
• Clean the filters (see page 16).
• Empty the water reservoir (see page 17).
Important!
If the drying programme has to be stopped before it
reaches the end, we recommend that you turn the
programme selector dial to position «Cooling» and
wait until the end of this phase before removing the
laundry. This will avoid a build-up of heat inside the
appliance. To do this first turn the dial to «Reset/
Off» and then to «Cooling» and press Start/Pause
button
.
Modifying the programme
To change a programme which is running, first cancel
it by turning the programme selector dial to «Reset/
Off». Select the new programme and press the
Start/Pause button.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Hints & Tips on Drying
Before placing articles of laundry in your tumble
dryer, check the care labels to ensure they are
recommended for tumble drying.
• Always load well spun laundry. The higher the spin
speed the lower the electricity consumption and the
shorter the drying time.
• DO NOT load dripping wet laundry into the dryer.
Roll the article in a towel or spin to remove excess
water.
Care Labels you may find on your laundry
may be tumble dried
• Close poppers and zips and fasten any buttons.
normal drying (high temperature)
delicate drying (low temperature)
do not tumble dry
• Sort the laundry. Separate synthetics from
cotton/linens, and dry separately.
• Remove the laundry immediately after the
programme has finished.
• Use a fabric conditioning sheet to reduce static. We
recommend the sheet is pinned to an article of
laundry (using a safety pin).
Do not overload the appliance.
Here is a list of the approximate weight of some
common laundry items.
• Mix the load i.e. large and small articles.
• When drying large items such as sheets, we
recommend you periodically stop the dryer to
redistribute the load.
Sheet
700 to 1000 g
Pillowcase
Tablecloth
Table Napkin
Kitchen Towel
Linen Hand Towel
Hand Towel
Bath Towel
Bathrobe
100 to 200 g
400 to 500 g
50 to 100 g
DO NOT use the tumble dryer to dry the following:
• Articles contaminated with inflammable substances
e.g. petrol, cleaning solvents, cooking oil, fats or
hair lacquer.
70 to 120 g
100 to 150 g
150 to 250 g
700 to 1000 g
1000 to 1500 g
200 to 300 g
150 to 200 g
• Woollen and synthetic/wool mixtures unless the
item is labelled as suitable for tumble drying.
• Very delicate articles such as silk.
Shirt
Apron
• Very large and bulky items such as duvets or
sleeping bags.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
You must disconnect the appliance from the
electricity supply, before you can carry out any
cleaning or maintenance work.
After a while, a whitish patina due to detergent
residue on laundry forms on the filters. When this
occurs, clean the filters with warm water using a
brush. Remove the filter in the door opening as per
picture (it can be positioned with the tooth facing to
the left or to the right).
External cleaning
Use water with a little mild washing-up liquid added
rinse and then dry thoroughly.
S
E
650
E
R
E
V
-
-
60'
T
O
R
U
kg
kg
2
1
,5 50'
30
'
A
/
12
00
3
5'
1000
7
0
/
-
-
90
95'
5'
800
80'
5
5'
-
-
'
00
/
1200
85'
5'
100
70'
6
10
50
'
/
90
0
90'
800
70'
3
-
-
5'
6
5'
3
-
-
4
kg
kg
5
2
0'
5
0'
5'
,5
Important: do not use methylated spirit, diluents or
similar products.
Cleaning the door
Clean periodically the interior part of the door to
remove any fluff from the seals around the filter.
P1152
Regular cleaning ensures correct drying.
S
E
650
E
R
E
V
5
0
'
-
60'
T
O
R
2
,
5
A
U
/
12
00
95'
65
'
kg
k
g
-
3
5'
1000
30
'
/
-
-
90
0
1
800
-
-
7
5'
/
12
00
1000
6
80
5'
'
100'
'
70
90
0
85
'
5
0'
/
800
70'
35'
5'
-
5
90
0'
'
-
-
45'
-
kg
kg
5
2
3
0'
5
,5
Do not use the appliance without filters.
Cleaning the condenser unit
Clean the air condenser when the «Please clean
condenser» message appears on the display.
The condenser is situated at the lower part of the
cabinet behind a small door. To open the door, push
the catch as per picture.
P1150
Cleaning the filters
Your dryer will only function well if the filters are
clean.
The filters collect all the fluff which accumulates
during drying and they must therefore be cleaned at
the end of each programme, before removing the
laundry, with a damp cloth. The «Please clean
filters» message appears on the display to remind
you to carry out this operation.
P1153
During the drying cycle or at the end, it is normal
for water to be present on the surface of the
condenser.
E
650
E
R
S
V
0'
5'
O
R
5
0
'
-
-
6
T
,
5
kg
k
g
2
1
A
U
/
12
00
95'
65'
3
1000
7
5
30
'
90
0
/
-
-
800
5'
0'
-
-
/
120
'
1
00'
70
'
0
1000
6
80
5'
90
0
85
'
/
800
70'
35'
5'
-
5
'
-
-
90
0'
45'
-
5
2
3
0'
kg
kg
5
,5
To pull out the condenser, first turn the two red stops
downwards as shown below and then remove the
condenser unit holding it at the handle.
P1151
P1110
The filter in the inner door must be removed for
cleaning.
Do not be alarmed by the amount of fluff. It is not
due to excessive wear caused by the dryer. All fabric
looses fluff when drying but it goes un-noticed in the
air. In a tumble dryer it simply collects in the filter.
P1155
P1154
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean it with a brush and rinse it under the shower if
necessary.
The reservoir must be re-inserted correctly.
If this is not done the same message comes on during
next drying and the programme stops, leaving the
laundry damp. The buzzer will sound.
After inserting the reservoir the START/PAUSE
button has to be pressed again to allow the
programme to continue.
Handy tip: The condensed water may be used in a
steam iron or to top up a battery, etc. In this case it
must be filtered (e.g. through a coffee filter).
P0639
Also clean the outside, removing all fluff.
Clean the rubber seal round the condenser cabinet
and in the inner part of the small door with a damp
cloth.
Cleaning the drum
When your laundry does not reach the desired degree
of dryness, in other words, when it turns out either
too dry or too damp,we advise you to clean the inside
of the drum with a cloth soaked with vinegar.
Important! Do not use pointed objects or utensils to
clean the spaces between the plates, as this could
damage the condenser and make it permeable.
This will eliminate the slight patina that has formed
in the drum (due to residues of detergent and
softeners used in the washing, and to the lime
contained in the water), which prevents the probes
from detecting the correct degree of dryness.
Re-fit the condenser, turn the red stops upwards and
close the door.
Do not use this appliance if the condenser
has not been fitted.
Emptying the water reservoir
Water extracted from the laundry condenses inside
the machine and is collected in a reservoir.
The reservoir must be emptied after each drying
cycle to ensure efficient operation when the machine
is next used.
The message «The tank is full, please empty»
written on the display reminds you to do this.
Proceed as follows:
• Pull out the reservoir
• Turn it upside down and let water flow down
• Re-fit the reservoir
P1157
P1156
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without
calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
During machine operation it is possible that one of the following messages appears on the display:
Problem with filters/condenser ......«Please clean filters/condenser» Please check filters/condenser.
Problem with water reservoir ........«The tank is full, please empty» Please check the water reservoir.
Door open ......................................«Can’t lock door» Please check the door.
Once the problem has been eliminated, press the START/PAUSE button to restart the programme.
IMPORTANT: if the «Warning» message and an alarm code (e.g. E21) appear on the display and the buzzer
sounds, switch the machine off and call the Service Centre.
Symptom
Possible causes
●
The tumble dryer does not
start
The door(s) has (have) not been closed («Can’t lock door»).
The plug is not properly inserted in the power socket.
There is no current at the socket.
The main fuse or the fuse in the plug has blown.
The selector dial is not set correctly.
The water reservoir is full or not properly inserted («The tank is full, please
empty»). The programme starts in any case but it stops after approx. 4 minutes.
●
●
●
●
●
●
●
The START/PAUSE Button has not been pressed.
The DELAY START option has been selected.
●
●
Drying takes too long or
laundry is not dry enough.
The laundry has not been spun properly.
The filters and/or the condenser are clogged up («Please clean
filters/condenser»).
●
●
●
●
●
●
●
The water reservoir is full («The tank is full, please empty»).
The room temperature is too high.
The selected time or drying cycle was not suitable for the laundry.
The HALF POWER
The HALF LOAD
option has been selected.
option has been selected.
There is too much laundry inside the appliance.
The dryer is not correctly installed.
If after the above checks, there is still a fault, call your local Service Force Centre.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Care Department
Service & Spare Parts
For Customer Services in the Republic of Ireland
please contact us at the address below:
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:
Zanussi-Electrolux
0870 5 929929
Electrolux Group (Ire) Ltd
Long Mile Road
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
Dublin 12
For the address of your local Service Force Centre
and further information about Service Force, please
Before calling out an engineer, please ensure you
have read the details under the heading “Something
Not Working”.
Republic of Ireland
Tel: +353 (0) 1 4090751
Email:[email protected]
For general enquiries concerning your Zanussi
Electrolux appliance or for further information on
Zanussi Electrolux products, please contact our
Customer Care Department by letter or telephone at
the address below or visit our website at
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The model and serial number of the appliance
(found on the rating plate - see picture)
5. The purchase date.
Customer Care Department
Major Appliances
Addington Way
Luton
Please note that a valid purchase receipt or
guarantee documentation is required for in-
guarantee service calls.
Bedfordshire
To buy accessories, consumables and spare parts
at our online shop please visit:
LU4 9QQ
Tel 08705 727727*
* calls to this number may be recorded for training
purposes.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee Conditions
Standard guarantee conditions
Exclusions
We, Zanussi Electrolux, undertake that if, within 12
months of the date of the purchase, this ZANUSSI
ELECTROLUX appliance or any part thereof is
proved to be defective by reason only of faulty
workmanship or materials, we will, at our option
repair or replace the same FREE OF ANY CHARGE
for labour, materials or carriage on condition that:
This guarantee does not cover:
●
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any
light bulbs or removable parts of glass or plastic.
●
Costs incurred for calls to put right an appliance
which is improperly installed or calls to
appliances outside the United Kingdom.
●
The appliance has been correctly installed and
●
Appliances found to be in use within a
used only on the electricity supply stated on the
rating plate.
commercial environment, plus those which are
subject to rental agreements.
●
The appliance has been used for normal domestic
●
Products of Zanussi Electrolux manufacture
purposes only, and in accordance with the
manufacturer’s instructions.
which are NOT marketed by Zanussi Electrolux.
●
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new
home subject to the following qualifications:
●
All service work under this guarantee must be
undertaken by a Service Force Centre.
●
Any appliance or defective part replaced shall
become the Company’s property.
The guarantee starts from the date you first
●
purchased your product.
●
This guarantee is in addition to your statutory and
other legal rights.
The guarantee is for the same period and to the
●
same extent for labour and parts as exists in the
new country of use for this brand or range of
products.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be
charged.
The guarantee relates to you and cannot be
●
transferred to another user.
Your new home is within the European
●
Community (EC) or European Free Trade Area.
The product is installed and used in accordance
●
with our instructions and is only used
domestically, i.e. a normal household.
The product is installed taking into account
●
regulations in your new country.
Before you move please contact your nearest
Customer Care Centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your move
and able to look after you and your appliances.
France
Germany
Italy
Senlis
+33 (0)344 62 29 29
+49 (0)800 234 7378
+39 (0)434 394 700
+46 (0)867 253 90
+44 (0)870 572 7727
Nurnberg
Pordenone
Stockholm
Luton
Sweden
UK
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Technical Specifications
DIMENSIONS
Height
Width
Depth
85 cm (33.5”)
60 cm (23.6”)
58 cm (22.8”)
POWER SUPPLY VOLTAGE
TOTAL POWER ADSORBED
240 V/50 Hz
2450 W (13A)
MAX LOAD CAPACITY
Cotton, linen
Synthetics
6.0.kg (13.2 lbs)
3
kg (06.6 lbs)
DRUM VOLUME
CONSUMPTIONS
108 l
Cotton, linen
Cotton, linen
Synthetics
3.84 kWh (6,5 kg store dry)
3.30 kWh (6,5 kg iron dry)
1.60 kWh (3 kg store dry)
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Level of Conductivity
Water contains, a variable quantity of limestone and
Approximative value
Display
Conductivity degree
mineral salts of which quantities vary according to
geographical locations thus varying its conductivity
values.
ºdH
Low
Medium
High
< 14
SO F T
NO RM AL
H ARD
Relevant variations of the conductivity of the water
compared to those prefixed by the factory could
slightly influence the residual humidity of the
laundry at the end of the cycle.
15 - 21
> 21
Your dryer allows you to regulate the sensitivity of
the drying sensor based on conductivity values of the
water by using the following procedure.
Memorising the new
setting:
To fix your choice press the «Exit»button.
Procedure:
Turn the programme selector dial to switch on the
appliance.
The previous selected drying cycle and options
appears again on the display and the buzzer sounds.
In selection mode press the «Option» button until the
Set Up menu appears on the display.
Press «Change» button to enter in the Set Up menu
and then press the «Option» button sequentially until
the message «Water hardness» appears.
Water Harness
Hard
Door
Spin
Options
Change
Exit
Adjusting the level of
conductivity:
Pressing «Change» button you can choose the
required water hardness degree.
The level of water hardness is indicated by 3 degree
shown on the display: hard, normal and soft.
Cotton extra
Cycle end at
08.30
10.55
1200
Water Harness
Hard
Door
Spin
Options
Change
Exit
Soft
Normal
Door
Spin
Options
Change
Exit
Normally, the appliance is factory-set to the
highest level; however, certain models may be
configured differently.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Stacking kit (optional accessory)
It should be possible to stack your new dryer on top
of a front loading washing machine with a lid depth
of between 48 and 60 cm.
Warning !
Slide out the polythene bag containing the
polystyrene block before using the appliance.
Read carefully the instructions supplied with the kit.
Pull off adhesive strips from inside machine on
top of drum
Please contact your local Service Force Centre or
retailer for further advice.
P1148
P1106
Door reversal
To make it easier to load or unload the laundry the
door can be reversed.
Should the appliance be moved, it must be
transported vertically.
This operation must be carried out by a Service
Force Engineer.
This will be a chargeable option
Positioning
It is recommended that, for your convenience, the
machine is positioned close to your washing
machine.
Please contact the nearest Zanussi-Electrolux Service
Force Centre.
The tumble dryer must be installed in a clean place,
where dirt does not build up.
Electrical connection
Air must be able to circulate freely all round the
appliance. Do not obstruct the front ventilation grill
or the air intake grills at the back of the machine.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
To keep vibration and noise to a minimum when the
dryer is in use, it should be placed on a firm, level
surface.
Once in its permanent operating position, check that
the dryer is absolutely level with the aid of a spirit
level. If it is not, raise or lower the feet until it is.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability
should this safety measure not be observed.
Should the appliance power supply cable
need to be replaced, this must be carried out
by our Service Centre.
The feet must never be removed.
Do not restrict the floor clearance through deep-
pile carpets, strips of wood or similar. This might
cause heat build-up which would interfere with
the operation of the appliance.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the
appliance’s rating plate. (See picture on page 4).
Important
The hot air emitted by the tumble dryer can reach
temperatures of up to 60°C. The appliance must
therefore not be installed on floors which are not
resistant to high temperatures.
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved BS 1363/A fuse
must be used.
When operating the tumble dryer, the room temperature
must not be lower than +5°C and higher than +35°C, as
it may affect the performance of the appliance.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Should the plug need to be replaced for any reason,
proceed as described below. The wires in the mains lead
are coloured in accordance with the following code:
Permanent connection
In the case of permanent connection it is necessary
that you install a double pole switch between the
appliance and the electricity supply (mains), with a
minimum gap of 3mm between the switch contacts
and of a type suitable for the required load in
compliance with the current electrical regulations.
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
GREEN & YELLOW
The switch must not break the yellow and green earth
cable at any point.
E
L
N
BROWN
BLUE
CORD CLAMP
P1041
The wire coloured green and yellow must be
connected to the terminal marked with the letter «E»
or by the earth symbol
yellow.
or coloured green and
The wire coloured blue must be connected to the
terminal «N» or coloured black.
The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
WARNING:
A cut off plug inserted into a 13 amp socket
is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
From the Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in
more than 150 countries around the world.
© Electrolux plc 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
|