Zanussi Clothes Dryer ZDC 5350 W User Manual

TUMBLE DRYER  
ZDC 5350 W  
RESET/  
OFF  
EXTRA  
PROGRAMME  
COTTON  
Extra dry  
Ready to wear  
Cooling  
Drying  
Cooling  
End  
Easy iron  
30 min  
PROGRAMME  
60 min  
Store dry  
TIMED  
Slightly damp  
Iron dry  
No  
Buzzer  
Quick  
Dry  
Low  
Delay  
Start/  
Pause  
Door  
Clogged Filters  
T
e
m
p
e
r
a
t
u
r
e
S
t
a
r
t
90 min  
Full Tank  
Clogged  
Baby dry  
Wring dry  
Extra dry  
Condenser  
T
I
M
E
L
I
N
E
6
kg  
Iron dry  
Store  
dry  
PROGRAMME  
SYNTHETIC  
FUNCTION  
START  
Z
D
C
5350W  
Unpacking: see page 18  
INSTRUCTION BOOKLET  
GB  
125992691  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 2  
Important Safety Information  
It is most important that this instruction book should be retained with the appliance for  
future reference. Should the appliance be sold or transferred to another owner, or should  
you move house and leave the appliance, always ensure that the book is supplied with the  
appliance in order that the new owner can get to know the functioning of the appliance  
and the relevant warnings.  
These warnings have been provided in the interest of safety. You MUST read them carefully  
before installing or using the appliance.  
Installation  
Use  
Do not overload the appliance (see programme  
chart).  
This appliance is heavy. Care should be taken when  
moving it.  
Clothes which are dripping wet should not be  
placed in the dryer.  
It is dangerous to alter the specifications or attempt  
to modify this product in any way.  
As some bulky items such as duvets and  
eiderdowns should be dried in large commercial  
machines because of their bulk, check with the  
manufacturer of the item if it is suitable for drying  
in a domestic machine, even if the dry weight of  
the item is within the limit advised.  
Any electrical work required to install this  
appliance should be carried out by a qualified  
electrician or competent person.  
Care must be taken to ensure that the appliance  
does not stand on the electrical supply cable.  
If the machine is situated on a carpeted floor,  
please adjust the feet in order to allow air to  
circulate freely.  
Please make sure that no gas lighters have  
accidentally been left in pockets of garments to be  
loaded into appliance.  
If the tumble dryer is placed on top of a washing  
machine, it is compulsory to use the stacking kit  
(optional accessory).  
Danger of explosion: Never tumble dry items that  
have been in contact with inflammable solvents  
(petrol, methylated spirits, dry cleaning fluid and  
the like). As these substance are volatile, they  
could cause an explosion. Only tumble dry items  
washed with water.  
Child Safety  
In order to avoid danger of fires caused by  
excessive drying, do not use appliance to dry the  
following items:  
This appliance is designed to be operated by adults.  
Children should not be allowed to tamper with the  
controls or play with the product.  
Cushions, quilts and the like (these items  
accumulate heat).  
Pets and children have been known to climb into  
tumble dryers. Please check your drum before use.  
Items containing rubber foam or materials similar  
to rubber foam.  
Keep all packaging well away for children.  
Leave the door slightly ajar when the appliance is  
not being used. This will allow the seal to be  
preserved.  
Clean fluff filters after using tumble dryer. To  
prevent fire risks, do not use the appliance if the  
fluff filters are damaged.  
Do not allow fluff to accumulate around the dryer.  
Under no circumstances should you attempt to  
repair the machine yourself. Repairs carried out by  
inexperienced persons may cause injury or serious  
malfunctioning. Contact your local Service Force  
Centre. Always insist on genuine Zanussi/  
Electrolux spare parts.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 3  
Contents  
Something Not Working  
Service and Spare Parts  
Customer Care  
13  
14  
14  
15  
For the User  
Important Safety Information  
2
Installation  
Child Safety  
Use  
Guarantee Conditions  
For the Installer  
Your New Tumble Dryer  
Description of the Appliance  
The Control Panel  
4
4
5
Installation Instructions  
16  
16  
17  
Technical Specifications  
Programme/Time Selector Dial  
Door Release Button  
No Buzzer Button  
Quick Dry Button  
Low Temperature Button  
Delay Start Button  
Display  
5
5
Adjusting the level of conductivity  
Unpacking  
Positioning  
Stacking kit (optional accessory)  
Door reversal  
Electrical connection  
18  
18  
5
5
18  
5
18  
6
18-19  
6-7  
7
Start/Pause Button  
Indicator Lights  
7
Programme Chart  
8
9
Operating Sequence  
Hints & Tips on Drying  
Maintenance and Cleaning  
10  
11  
External cleaning  
Cleaning the door  
11  
11  
Cleaning the filters  
11  
Cleaning the condenser unit  
Emptying the water reservoir  
Cleaning the drum  
11-12  
12  
12  
Cleaning the air intake grill  
12  
Guide to use the Instruction Book  
The following symbols will be found in the text to guide you throughout the instructions:  
Safety instructions  
Hints and tips  
Environmental information  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 4  
Your New Tumble Dryer  
This tumble dryer will give your wash that soft, relaxed feel whatever  
the weather.  
Extremely high quality standards both during development and  
manufacturing guarantee a long service life for your appliance.  
Maximum economy in the operation of your dryer is achieved through  
very economical electricity consumption and short drying times.  
Energy saving tips  
In the interest  
of the environment  
To save energy we recommend that you follow these  
hints:  
Materials marked with the symbol  
are  
Try to load to the maximum capacity of the  
recyclable.  
machine as small loads are uneconomical.  
Check with your local Council or Environmental  
Health Office to see if there are facilities in your  
area for re-cycling this appliance.  
Always load well spun laundry. The higher the spin  
speed, the lower the electricity consumption and  
the shorter the drying times.  
When the appliance is to be scrapped, cut off the  
power supply cable and make the door closing  
device unusable to prevent young children from  
being trapped inside.  
Do not over-dry laundry, this avoids creasing and  
saves energy.  
Clean the filters regularly to avoid excessive drying  
times and high electricity consumption.  
Help to keep your country tidy - use authorised  
disposal sites for your old appliance.  
Ventilate the room well. The room temperature  
should not exceed +35°C during drying.  
How do we help to protect the  
environment? We use recycled paper!  
Description of the Appliance  
01 Control panel  
02 Water reservoir  
ing  
Dry  
Coo  
End  
ling  
N
TO  
1
F
ilters  
COT  
d
gge  
Clo  
SET/  
O
RE  
y
r
a
d
r
S
tart/  
e
ank  
FF  
Ext  
T
ear  
y
Paus  
Full  
Ready to  
w
Delay  
rt  
gged  
Clo  
ense  
ond  
C
ooling  
r
TRA  
E
Low  
Sta  
EX  
PR  
M
r
e
C
k
Dry  
ratu  
RAM  
e
dr  
Quic  
pe  
OG  
Stor  
T
em  
03 Drum light  
on  
Easy ir  
N
o
0W  
35  
er  
uzz  
C
ZD  
5
p
o
r
B
Do  
Slightly dam  
m
in  
ST  
A
RT  
30  
ED  
GR  
TIM  
M
E
y
AM  
PRO  
min  
Iron dr  
60  
y
N
g
dr  
IO  
3
4
C
T
90  
m
in  
Wrin  
FUN  
y
IC  
a
Extr  
dr  
THET  
SYN  
dry  
Baby  
e
Stor  
dr  
ry  
d
n
Iro  
y
E
MM  
O
G
RA  
PR  
kg  
6
E
I
N
E
L
04 Fluff filters  
I
M
T
2
05 Rating Plate  
06 Condenser unit  
07 Adjustable feet  
5
4
7
6
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 5  
The Control Panel  
RESET/  
EXTRA  
OFF  
COTTON  
Extra dry  
Cooling  
PROGRAMME  
Drying  
Cooling  
End  
Easy iron  
Ready to wear  
Store dry  
30 min  
PROGRAMME  
60 min  
TIMED  
Slightly damp  
No  
Buzzer  
Quick  
Low  
Delay  
Start/  
Pause  
Door  
Clogged Filters  
Full Tank  
Dry Temperature Start  
90 min  
Iron dry  
Clogged  
Condenser  
Baby dry  
Wring dry  
TIMELINE  
6
kg  
Iron dry  
Extra dry  
Store  
dry  
PROGRAMME  
SYNTHETIC  
FUNCTION  
START  
ZDC 5350W  
1
2 3 4 5 6 7 8  
9
3NO BUZZER Button  
1
Programme/Time  
Selector Dial  
A buzzer sounds  
• when selecting the programme  
• when depressing the buttons  
• when an incorrect option selection is made  
Allows you to select electronically controlled or time  
controlled drying.  
Turn the dial to the required programme or time.  
• when the programme selector dial is turned to  
another position during the programme or when  
you depress an option button during the cycle  
Electronically controlled drying (automatic)  
The appliance runs these programmes with the help  
of probes which detect the degree of dampness of the  
laundry.  
Simply select the programme according to the type of  
laundry and degree of drying required.  
• at the end of the programme and during the  
anticrease phase  
• when the water reservoir is full  
• if the machine is not working correctly  
• when the small door at the bottom is open.  
Time controlled drying  
This can be used to finish off drying if necessary.  
Select the 90 or 60 minute programme for cottons or  
the 30 minute programme for synthetics.  
By depressing the button the acoustic signal is  
switched off.  
The corresponding light comes on.  
To cancel a programme which is running, turn the  
programme selector dial to “RESET/OFF”.  
At the end of drying, turn the selector dial to  
RESET/OFF” to switch the machine off before  
removing the laundry.  
4QUICK DRY Button  
By depressing this button the drying time is reduced  
in the following COTTON programmes:  
EXTRA DRY  
READY TO WEAR  
STORE DRY  
2
DOOR RELEASE Button  
Press this button to open the door. The light above  
the button will illuminate.  
The corresponding pilot light comes on.  
This option cannot be selected with LOW  
TEMPERATURE function.  
Opening the door by means of this button is  
possible only if the tumble dryer is on  
(programme selector dial set to a programme or  
drying time).  
If you open the door during a programme, in order to  
restart the programme you must press the  
START/PAUSE button again after having closed the  
door.  
5LOW TEMPERATURE  
Button  
Pressing this button allows drying to be performed at  
a lower temperature, for delicate items.  
The corresponding pilot light comes on.  
This option can also be used for time controlled  
drying.  
This option cannot be selected with QUICK DRY.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 6  
Duration of selected programme  
6DELAY START button  
After you have selected the programme, its  
duration (in hours and minutes) appears on the  
display. It is calculated automatically on the basis  
of the maximum load accepted for each type of  
fabric and of the required degree of drying.  
This button allows you to delay the starting of the  
programme by 12 hours max.  
This option must be selected after having selected  
the programme and before pressing START/PAUSE  
to start the programme.  
Every time the button is pressed, the time is  
increased by 30 minutes, until the display shows a  
delay of “2 hours”. After this, the delay is displayed  
hour by hour.  
1.20  
The minutes or hours of delay that have been  
selected are displayed for 2 seconds, then the display  
shows the duration of the previously selected  
programme.  
The countdown begins after you have pressed the  
START/PAUSE button.  
When the programme starts, the remaining time is  
displayed every 5 minutes.  
To cancel the delay time press the START/PAUSE  
button and after press the DELAY START button  
until the display indicates 0’. Then press the  
START/PAUSE button again.  
Delayed start  
If you have selected a delay time by means of the  
relevant button, the display shows it for 2 seconds;  
then it shows the duration of the previously  
selected programme.  
The countdown is displayed every 30 minutes until it  
displays “90 minutes” and then hour by hour.  
When the delay is cancelled, the display shows 0’ and  
after the duration of the programme.  
During the delayed start, it is not possible to change  
the programme or the delay time that have been  
selected. To do this, you must first switch off the  
machine by setting the programme selector dial to  
“RESET/OFF”. Select the new programme, the  
options and the delayed start, then press the  
START/PAUSE button.  
3
To cancel or change options that have been selected,  
simply set the appliance to PAUSE. Once you  
perform the desired operation, press once again the  
START/PAUSE button.  
End of programme  
If you wish to add more laundry while the machine is  
performing the countdown, simply open the door.  
When you close the door, press the START/PAUSE  
button again to resume the countdown.  
A flashing zero indicates the end of the  
programme and it is displayed after the “anti-  
creasing” phase.  
7DISPLAY  
The display shows the following information:  
• duration of selected programme  
• delayed start  
0
• end of programme  
• incorrect option selection  
• alarm code  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 17:51 Pagina 7  
Incorrect option selection  
If you select an option that is not compatible with  
the programme you have selected, the display  
shows Err (error).  
8START/PAUSE button  
Press this button to start the dryer after having  
selected the programme and the options.  
The relevant light will stop flashing. If you have  
chosen a delayed start, the machine will begin the  
countdown.  
If the door of the appliance or the small door at  
the bottom is opened while the programme is  
running, this button must be pressed again after  
closing the door in order to restart the  
programme from the point at which it was  
interrupted.  
This button must also be depressed after a power  
failure and after having re-inserted the water  
reservoir, if it has been emptied in the middle of a  
programme, after the “FULL TANK” has  
illuminated.  
In both cases the light of the Start/Pause button  
flashes to remind you that the start button needs to be  
pressed again.  
This code will reappear during the execution of the  
programme if you press one of the option buttons or  
turn the programme selector.  
If you press the Start/Pause button and the door or  
the small door, situated at the lower part of the  
cabinet, is opened, the «Err» code will reappear  
again on the display.  
Alarm code  
9 Indicator Lights  
In the case of a functional problem, the display  
shows an alarm code (e.g. E21). See page 13 for  
more detailed information.  
These lights indicate the following functions:  
“DRYING” light  
This light indicates that the appliance is in the drying  
phase.  
“COOLING” light  
E21  
This light indicates that the appliance is in the  
cooling phase. At the end of drying, there is a 10  
minute cooling phase to cool the laundry.  
“END” light  
This light is on at the end of the cooling phase,  
during the anti-creasing phase and at the end of the  
programme.  
“CLOGGED FILTERS” light  
This light illuminates at the end of the programme to  
remind you that the filters must be cleaned.  
“FULL TANK” light  
This light comes on at the end of the programme to  
remind you that the water reservoir must be emptied.  
If this light illuminates during a programme this  
means that the water reservoir is full. The buzzer  
sounds, the programme stops, the light of the  
Start/Pause button flashes.  
“CLOGGED CONDENSER” light  
It comes on every 80 cycles to remind you that the  
condenser must be cleaned.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 8  
Programme Chart  
Automatic drying (electronic programmes)  
Degree of drying  
Type of laundry  
required  
Max-load (1)  
Programme  
Extra dry  
Ready to wear  
Store dry  
Slightly damp  
Iron dry  
6 kg  
6 kg  
6 kg  
6 kg  
6 kg  
6 kg  
EXTRA DRY  
READY TO WEAR  
STORE DRY(*)  
SLIGHTLY DAMP  
IRON DRY(*)  
COTTON  
Wring dry  
WRING DRY  
Extra dry  
Store dry  
Iron dry  
2.5 kg  
2.5 kg  
2.5 kg  
EXTRA DRY  
STORE DRY(*)  
IRON DRY  
SYNTHETICS  
1 kg  
(10 jumpers)  
BABY DRY  
EASY IRON  
JUMPERS  
Baby dry  
Easy iron  
1 kg  
Jackets, shirts, blouses.  
(*) According to IEC 61121 Standards.  
• Baby Dry cycle is a special programme for jumpers to be dried “READY TO WEAR”.  
Time controlled drying  
Type of laundry  
Programme  
selector dial position  
Drying time  
Max-load (1)  
COTTON  
90’  
60’  
30’  
6,5 kg  
6,5 kg  
2.5 kg  
90 min  
60 min  
30 min  
COTTON  
SYNTHETICS  
(1) Never overfill the drum (do not load large quilts, for example).  
Drying times vary according to:  
• The type of laundry  
• The size of the load  
• The degree of spinning prior to drying.  
• The degree of dryness required  
Cooling  
This position on the programme selector dial can be used to freshen the laundry (e.g. to remove a persistent  
odour of moth-balls).  
Load  
It is often difficult to estimate the weight of items to be dried. We therefore recommend that you adopt the  
following guidelines:  
cotton, linen: drum full but not too tightly packed;  
synthetics: drum no more than half full;  
delicate fabrics: drum no more than one third full.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 9  
Operating Sequence  
9. If the laundry is not removed at the end of the  
Before using your tumble dryer for the first time, we  
recommend to place a few damp cloths inside the  
appliance and dry for 30 minutes.  
cycle, the dryer performs an anti-creasing phase  
(duration: 30 minutes maximum).  
There may be dust inside a brand new tumble dryer.  
If you do not remove the laundry, the dryer will  
stop automatically at the end of the anti-creasing  
phase.  
The END, CLOGGED FILTERS and FULL  
TANK lights remain lit and the buzzer sounds for  
2 minutes.  
Drying  
1. Connect the appliance.  
2. Open the door (see picture).  
The START/PAUSE button goes off and a  
flashing zero appears on the display.  
10.Turn the programme selector dial to “RESET/  
OFF”; all the lights go out. The appliance is  
switched off.  
Remove the laundry.  
If you open and then close the door before  
turning the programme selector dial to  
“RESET/OFF”, all the lights corresponding to  
the phases making up the performed  
programme come on and the display shows the  
duration of the programme.  
P1149  
P1108  
3. Load the items one at a time, shaking them out  
loosely.  
4. Close the door. Please check the laundry does not  
get caught between the door and filter.  
After each use  
5. Select the drying programme or time. The lights  
DRYING, COOLING and END come on. The  
light of the START/PAUSE button flashes and the  
display shows the duration of the programme.  
• Clean the filters (see page 11).  
• Empty the water reservoir (see page 12).  
6. If required, press the LOW TEMPERATURE  
button and/or the NO BUZZER button or the  
QUICK DRY button.  
Important!  
If the drying programme has to be stopped before it  
reaches the end, we recommend that you turn the  
programme selector dial to position “Cooling” and  
wait until the end of this phase before removing the  
laundry. This will avoid a build-up of heat inside the  
appliance. To do this first turn the dial to “RESET/  
OFF” and then to “Cooling” and depress  
7. Select the DELAY START if required. The  
selected delay appears on the display for 2  
seconds, then the duration of the selected  
programme is displayed.  
8. Press the START/PAUSE button: the  
corresponding light stops flashing and drying  
starts. Only the DRYING light stays lit. If you  
have selected the DELAY START, the machine  
begins its countdown.  
START/PAUSE Button  
.
Modifying the programme  
To change a programme which is running, first cancel  
it by turning the programme selector dial to “RESET/  
OFF”. Select the new programme and press the  
START/PAUSE Button.  
If the programme selector dial is turned to another  
position, when the machine is running, the buzzer  
will sound, the programme phase indicator lights  
will flash and Err appears on the display.  
The drum turns alternately in both directions  
during drying.  
All drying programmes end with a 10 minute  
cooling phase (light COOLING is on).  
You may remove the laundry after this phase.  
The END, CLOGGED FILTERS and FULL  
TANK lights illuminate. The display shows a  
static zero and the buzzer sounds to indicate the  
end of the cycle.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 10  
Hints & Tips on Drying  
Before placing articles of laundry in your tumble  
dryer, check the care labels to ensure they are  
recommended for tumble drying.  
Always load well spun laundry. The higher the spin  
speed the lower the electricity consumption and the  
shorter the drying time.  
DO NOT load dripping wet laundry into the dryer.  
Roll the article in a towel or spin to remove excess  
water.  
Care Labels you may find on your laundry  
may be tumble dried  
Close poppers and zips and fasten any buttons.  
normal drying (high temperature)  
delicate drying (low temperature)  
do not tumble dry  
Sort the laundry. Separate synthetics from  
cotton/linens, and dry separately.  
Remove the laundry immediately after the  
programme has finished.  
Use a fabric conditioning sheet to reduce static. We  
recommend the sheet is pinned to an article of  
laundry (using a safety pin).  
Do not overload the appliance.  
Here is a list of the approximate weight of some  
common laundry items.  
Mix the load i.e. large and small articles.  
When drying large items such as sheets, we  
recommend you periodically stop the dryer to  
redistribute the load.  
Sheet  
700 to 1000 g  
100 to 200 g  
400 to 500 g  
50 to 100 g  
Pillowcase  
Tablecloth  
Table Napkin  
Kitchen Towel  
Linen Hand Towel  
Hand Towel  
Bath Towel  
Bathrobe  
DO NOT use the tumble dryer to dry the following:  
Articles contaminated with inflammable substances  
e.g. petrol, cleaning solvents, cooking oil, fats or  
hair lacquer.  
70 to 120 g  
100 to 150 g  
150 to 250 g  
700 to 1000 g  
1000 to 1500 g  
200 to 300 g  
150 to 200 g  
Woollen and synthetic/wool mixtures unless the  
item is labelled as suitable for tumble drying.  
Very delicate articles such as silk.  
Shirt  
Apron  
Very large and bulky items such as duvets or  
sleeping bags.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:12 Pagina 11  
Maintenance and Cleaning  
You must disconnect the appliance from the  
electricity supply, before you can carry out any  
cleaning or maintenance work.  
After a while, a whitish patina due to detergent  
residue on laundry forms on the filters. When this  
occurs, clean the filters with warm water using a  
brush. Remove the filter in the door opening as per  
picture (it can be positioned with the tooth facing to  
the left or to the right).  
External cleaning  
Use and water and a mild washing up liquid then dry  
thoroughly.  
S
E
650  
E
R
E
V
-
-
60'  
T
O
R
U
kg  
kg  
2
1
,5 50'  
30  
'
A
/
12  
00  
3
5'  
1000  
7
0
/
-
-
90  
95'  
5'  
800  
80'  
5
5'  
-
-
'
00  
/
1200  
85'  
5'  
100  
70'  
6
10  
50  
'
/
90  
0
90'  
800  
70'  
3
-
-
5'  
6
5'  
3
-
-
4
kg  
kg  
5
2
0'  
5
0'  
5'  
,5  
Important: do not use methylated spirit, diluents or  
similar products.  
Cleaning the door  
Clean periodically the interior part of the door to  
remove any fluff from the seals around the filter.  
P1152  
Regular cleaning ensures correct drying.  
S
E
650  
E
R
E
V
5
0
'
-
60'  
T
O
R
2
,
5
A
U
/
12  
00  
95'  
65  
'
kg  
k
g
-
3
5'  
1000  
30  
'
/
-
-
90  
0
1
800  
-
-
7
5'  
/
12  
00  
1000  
6
80  
5'  
'
100'  
'
70  
90  
0
85  
'
5
0'  
/
800  
70'  
35'  
5'  
-
5
90  
0'  
'
-
-
45'  
-
kg  
kg  
5
2
3
0'  
5
,5  
Do not use the appliance without filters.  
Cleaning the condenser unit  
Clean the air condenser when CLOGGED  
CONDENSER light comes on.  
The condenser is situated at the lower part of the  
cabinet behind a small door. To open the door, push  
the catch as per picture.  
P1150  
Cleaning the filters  
Your dryer will only function well if the filters are  
clean.  
The filters collect all the fluff which accumulates  
during drying and they must therefore be cleaned at  
the end of each programme, before removing the  
laundry, with a damp cloth. The CLOGGED  
FILTERS light reminds you to carry out this  
operation.  
P1153  
During the drying cycle or at the end, it is normal  
for water to be present on the surface of the  
condenser.  
E
650  
E
R
S
V
0'  
5'  
O
R
5
0
'
-
-
6
T
,
5
kg  
k
g
2
1
A
U
/
12  
00  
95'  
65'  
3
1000  
7
5
30  
'
90  
0
/
-
-
800  
5'  
0'  
-
-
/
120  
'
1
00'  
70  
'
0
1000  
6
80  
5'  
90  
0
85  
'
/
800  
70'  
35'  
5'  
-
5
'
-
-
90  
0'  
45'  
-
5
2
3
0'  
kg  
kg  
5
,5  
To pull out the condenser, first turn the two red stops  
downwards as shown below and then remove the  
condenser unit holding it at the handle.  
P1151  
P1110  
The filter in the inner door must be removed for  
cleaning.  
Do not be alarmed by the amount of fluff. It is not  
due to excessive wear caused by the dryer. All fabric  
looses fluff when drying but it goes un-noticed in the  
air. In a tumble dryer it simply collects in the filter.  
P1155  
P1154  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 12  
Clean it with a brush and rinse it under the shower if  
necessary.  
The reservoir must be re-inserted correctly.  
If this is not done the pilot light FULL TANK comes  
on during next drying and the programme stops,  
leaving the laundry damp. The buzzer will sound.  
After inserting the reservoir the START/PAUSE  
button has to be depressed again to allow the  
programme to continue.  
Handy tip: The condensed water may be used in a  
steam iron or to top up a battery, etc. In this case it  
must be filtered (e.g. through a coffee filter).  
P0639  
Also clean the outside, removing all fluff.  
Clean the rubber seal round the condenser cabinet  
and in the inner part of the small door with a damp  
cloth.  
Cleaning the drum  
When your laundry does not reach the desired degree  
of dryness, in other words, when it turns out either  
too dry or too damp,we advise you to clean the inside  
of the drum with a cloth soaked with vinegar.  
Important! Do not use pointed objects or utensils to  
clean the spaces between the plates, as this could  
damage the condenser and make it permeable.  
This will eliminate the slight patina that has formed  
in the drum (due to residues of detergent and  
softeners used in the washing, and to the lime  
contained in the water), which prevents the probes  
from detecting the correct degree of dryness.  
Re-fit the condenser, turn the red stops upwards and  
close the door.  
Do not use this appliance if the condenser  
has not been fitted.  
Cleaning the air intake grill  
Using a vacuum cleaner remove the fluff from the air  
intake grill at the back of the appliance.  
Emptying the water reservoir  
Water extracted from the laundry condenses inside  
the machine and is collected in a reservoir.  
The reservoir must be emptied after each drying  
cycle to ensure efficient operation when the machine  
is next used.  
The FULL TANK light reminds you this operation.  
Proceed as follows:  
Pull out the reservoir  
Turn it upside down and let water flow down  
Re-fit the reservoir  
P1162  
P1157  
P1156  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 13  
Something Not Working  
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without  
calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.  
IMPORTANT: if the END light flashes, the buzzer sounds and an alarm code is displayed, switch the machine  
off and call the Service Centre.  
Symptom  
Possible causes  
The tumble dryer does not  
start  
The door(s) has (have) not been closed.  
The plug is not properly inserted in the power socket.  
There is no current at the socket.  
The main fuse or the fuse in the plug has blown.  
The selector dial is not set correctly.  
The water reservoir is full or not properly inserted (the FULL TANK light is on).  
The programme starts in any case but it stops after approx. 4 minutes.  
The START/PAUSE Button has not been depressed.  
The DELAY START option has not been selected.  
Drying takes too long or  
laundry is not dry enough.  
The laundry has not been spun properly.  
The filters and/or the condenser are clogged up.  
The water reservoir is full.  
The room temperature is too high.  
The selected time or drying cycle was not suitable for the laundry.  
The LOW TEMPERATURE button has been pressed.  
There is too much laundry inside the appliance.  
The dryer is not correctly installed.  
The drum light does not  
light up:  
The Programme/Time selector dial is on position “RESET/OFF”.  
The lamp is defective.  
If after the above checks, there is still a fault, call your local Service Force Centre.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 14  
Customer Care Department  
Service & Spare Parts  
In the event of your appliance requiring service, or if  
you wish to purchase spare parts, please contact your  
local Service Force Centre by telephoning:  
For Customer Services in the Republic of Ireland  
please contact us at the address below:  
Zanussi-Electrolux  
0870 5 929929  
Electrolux Group (Ire) Ltd  
Long Mile Road  
Your telephone call will be automatically routed to the  
Service Force Centre covering your post code area.  
Dublin 12  
For the address of your local Service Force Centre  
and further information about Service Force, please  
Before calling out an engineer, please ensure you  
have read the details under the heading “Something  
Not Working”.  
Republic of Ireland  
Tel: +353 (0) 1 4090751  
For general enquiries concerning your Zanussi  
Electrolux appliance or for further information on  
Zanussi Electrolux products, please contact our  
Customer Care Department by letter or telephone at  
the address below or visit our website at  
When you contact the Service Force Centre you will  
need to give the following details:  
1. Your name, address and post code  
2. Your telephone number  
3. Clear and concise details of fault  
4. The model and serial number of the appliance  
(found on the rating plate - see picture)  
5. The purchase date.  
Customer Care Department  
Zanussi Electrolux  
55-77 High Street  
Slough  
Please note that a valid purchase receipt or  
guarantee documentation is required for in-  
guarantee service calls.  
Berkshire  
SL1 1DZ  
Tel 08705 727727*  
* calls to this number may be recorded for training  
purposes.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 15  
Guarantee Conditions  
Standard guarantee conditions  
Exclusions  
We, Zanussi Electrolux, undertake that if, within 12  
months of the date of the purchase, this ZANUSSI  
ELECTROLUX appliance or any part thereof is  
proved to be defective by reason only of faulty  
workmanship or materials, we will, at our option  
repair or replace the same FREE OF ANY CHARGE  
for labour, materials or carriage on condition that:  
This guarantee does not cover:  
Damage or calls resulting from transportation,  
improper use or neglect, the replacement of any  
light bulbs or removable parts of glass or plastic.  
Costs incurred for calls to put right an appliance  
which is improperly installed or calls to  
appliances outside the United Kingdom.  
The appliance has been correctly installed and  
Appliances found to be in use within a  
used only on the electricity supply stated on the  
rating plate.  
commercial environment, plus those which are  
subject to rental agreements.  
The appliance has been used for normal domestic  
Products of Zanussi Electrolux manufacture  
purposes only, and in accordance with the  
manufacturer’s instructions.  
which are NOT marketed by Zanussi Electrolux.  
The appliance has not been serviced, maintained,  
repaired, taken apart or tampered with, by any  
person not authorised by us.  
European guarantee  
If you should move to another country within Europe  
then your guarantee moves with you to your new  
home subject to the following qualifications:  
All service work under this guarantee must be  
undertaken by a Service Force Centre.  
Any appliance or defective part replaced shall  
become the Company’s property.  
The guarantee starts from the date you first  
purchased your product.  
This guarantee is in addition to your statutory and  
other legal rights.  
The guarantee is for the same period and to the  
same extent for labour and parts as exists in the  
new country of use for this brand or range of  
products.  
Home visits are made between 8.30am and 5.30pm  
Monday to Friday. Visits may be available outside  
these hours in which case a premium will be  
charged.  
The guarantee relates to you and cannot be  
transferred to another user.  
Your new home is within the European  
Community (EC) or European Free Trade Area.  
The product is installed and used in accordance  
with our instructions and is only used  
domestically, i.e. a normal household.  
The product is installed taking into account  
regulations in your new country.  
Before you move please contact your nearest  
Customer Care Centre, listed below, to give them  
details of your new home. They will then ensure that  
the local Service Organisation is aware of your move  
and able to look after you and your appliances.  
France  
Germany  
Italy  
Senlis  
+33 (0) 344 62 29 29  
+49 (0) 800 234 7378  
+39 0434 39 4700  
Nurnberg  
Pordenone  
Stockholm  
Slough  
Sweden  
UK  
+46 (0) 8 672 53 90  
+44 (0) 1753 219897  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 16  
Installation Instructions  
It is dangerous to alter the specifications or  
attempt to modify this product in any way.  
Care must be taken to ensure that the appliance  
does not stand on the electrical supply cable.  
Any electrical work required to install this  
appliance should be carried out by a qualified  
electrician or competent person.  
Technical Specifications  
DIMENSIONS  
Height  
Width  
Depth  
85 cm (33.5”)  
60 cm (23.6”)  
58 cm (22.8”)  
POWER SUPPLY VOLTAGE  
TOTAL POWER ABSORBED  
230-240 V/50 Hz  
2450 W (13A)  
MAX LOAD CAPACITY  
Cotton, linen  
Synthetics  
6.0.kg (13.2 lbs)  
2.5 kg (05.5 lbs)  
DRUM VOLUME  
CONSUMPTIONS  
108 l  
Cotton, linen  
Cotton, linen  
Synthetics  
4.37 kWh (6,5 kg store dry)  
3.6 kWh (6,5 kg iron dry)  
1.40 kWh (2,5 kg store dry)  
This appliance complies with the following E.E.C. Directives:  
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;  
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 17  
Adjusting the level of conductivity  
Water contains, a variable quantity of limestone and  
Approximative value  
Display  
Conductivity degree  
mineral salts of which quantities vary according to  
geographical locations thus varying its conductivity  
values.  
ºdH  
Low  
Medium  
High  
< 14  
C0  
C0  
C0  
Relevant variations of the conductivity of the water  
compared to those prefixed by the factory could  
slightly influence the residual humidity of the  
laundry at the end of the cycle.  
15 - 21  
> 21  
Your dryer allows you to regulate the sensitivity of  
the drying sensor based on conductivity values of the  
water by using the following procedure.  
Normally, the appliance is factory-set to the  
highest level; however, certain models may be  
configured differently.  
Procedure:  
Turn the programme selector dial to switch on the  
appliance  
Memorising the new  
setting:  
Simultaneously press down buttons 3 and 6 until the  
previous drying cycle time appears again on the  
display and the buzzer sounds.  
In selection mode press simultaneously the buttons 3  
and 6 until «C0» appears on the digits.  
RESET/  
OFF  
EXTRA  
COTTON  
Extra dry  
Ready to wear  
PROGRAMME  
Cooling  
Drying  
Cooling  
End  
Easy iron  
1.25  
Store dry  
30 min  
PROGRAMME  
60 min  
TIMED  
Slightly damp  
Iron dry  
No  
Buzzer  
Quick  
Low  
Delay  
Start/  
Pause  
Door  
Clogged Filters  
Full Tank  
Dry Temperature Start  
90 min  
Clogged  
Baby dry  
Wring dry  
Extra dry  
1
2
3
4
6
5
Condenser  
Iron dry  
Store  
dry  
PROGRAMME  
SYNTHETIC  
FUNCTION  
ZDC 5350W  
Adjusting the level of  
conductivity:  
Press button 5 sequentially: the level of conductivity  
is indicated by the lighting of the horizontal hyphens.  
Drying  
Cooling  
End  
No  
Buzzer  
Quick  
Low  
Delay  
Start/  
Pause  
Clogged Filters  
Full Tank  
Dry Temperature Start  
Clogged  
Condenser  
2 3 4  
6
5
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 18  
Unpacking  
Stacking kit (optional accessory)  
It should be possible to stack your new dryer on top  
of a front loading washing machine with a lid depth  
of between 48 and 60 cm.  
Warning !  
Slide out the polythene bag containing the  
polystyrene block before using the appliance.  
Read carefully the instructions supplied with the kit.  
Please contact your local Service Force Centre or  
retailer for further advice.  
P1148  
P1106  
Should the appliance be moved, it must be  
transported vertically.  
Door reversal  
To make it easier to load or unload the laundry the  
door can be reversed.  
This operation must be carried out by qualified  
Service Force Engineer.  
Please contact the nearest Zanussi/Electrolux Service  
Force Centre.  
Positioning  
It is recommended that, for your convenience, the  
machine is positioned close to your washing  
machine.  
The tumble dryer must be installed in a clean place,  
where dirt does not build up.  
Electrical connection  
Any electrical work required to install this appliance  
should be carried out by a qualified electrician or  
competent person.  
Air must be able to circulate freely all round the  
appliance. Do not obstruct the front ventilation grille  
or the air intake grills at the back of the machine.  
To keep vibration and noise to a minimum when the  
dryer is in use, it should be placed on a firm, level  
surface.  
Once in its permanent operating position, check that  
the dryer is absolutely level with the aid of a spirit  
level. If it is not, raise or lower the feet until it is.  
WARNING: THIS APPLIANCE MUST BE  
EARTHED.  
The manufacturer declines any liability  
should this safety measure not be observed.  
Should the appliance power supply cable  
need to be replaced, this must be carried out  
by our Service Centre.  
The feet must never be removed.  
Do not restrict the floor clearance through deep-  
pile carpets, strips of wood or similar. This might  
cause heat build-up which would interfere with  
the operation of the appliance.  
Before switching on, make sure the electricity supply  
voltage is the same as that indicated on the  
appliance’s rating plate. (See picture on page 4).  
Important  
The appliance is supplied with a 13amp plug fitted.  
In the event of having to change the fuse in the plug  
supplied, a 13amp ASTA approved BS 1363/A fuse  
must be used.  
The hot air emitted by the tumble dryer can reach  
temperatures of up to 60°C. The appliance must  
therefore not be installed on floors which are not  
resistant to high temperatures.  
When operating the tumble dryer, the room temperature  
must not be lower than +5°C and higher than +35°C, as  
it may affect the performance of the appliance.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 19  
Should the plug need to be replaced for any reason,  
proceed as described below. The wires in the mains lead  
are coloured in accordance with the following code:  
Permanent connection  
In the case of permanent connection it is necessary  
that you install a double pole switch between the  
appliance and the electricity supply (mains), with a  
minimum gap of 3mm between the switch contacts  
and of a type suitable for the required load in  
compliance with the current electrical regulations.  
Green and Yellow  
Blue  
- Earth  
- Neutral  
- Live  
Brown  
GREEN & YELLOW  
The switch must not break the yellow and green earth  
cable at any point.  
E
L
N
BROWN  
BLUE  
CORD CLAMP  
P1041  
The wire coloured green and yellow must be  
connected to the terminal marked with the letter «E»  
or by the earth symbol  
yellow.  
or coloured green and  
The wire coloured blue must be connected to the  
terminal «N» or coloured black.  
The wire coloured brown must be connected to the  
terminal marked «L» or coloured red.  
Upon completion there must be no cut, or stray  
strands of wire present and the cord clamp must be  
secure over the outer sheath.  
WARNING:  
A cut off plug inserted into a 13 amp socket  
is a serious safety (shock) hazard.  
Ensure that the cut off plug is disposed of  
safely.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125992691.qxd 26/05/2004 11:13 Pagina 20  
From the Electrolux Group. The world’s No. 1 choice.  
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor  
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,  
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in  
more than 150 countries around the world.  
© Electrolux plc 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Westinghouse Computer Monitor L1920NW User Manual
Westinghouse Slow Cooker WST3011ZE 3 User Manual
Wharfedale Portable Speaker SVP 10 User Manual
Wharfedale Speaker D91 User Manual
Whirlpool Ventilation Hood GZ7930XG User Manual
Woodstock Saw W1706 User Manual
Xerox Copier MO3098Y6 1 User Manual
Xilinx Life Jacket 82i User Manual
Zanussi Washer Dryer ZWF 10070 W User Manual
Zenith Home Theater System DVT812 User Manual