R1 Extender
Quick Installation Guide
V1.0 January 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction
Introduction
The R1 Extender is a high-performance outdoor-deployable wireless bridge that provides
wireless connectivity among multiple network locations. It supports Base Station, CPE, PTP
and PTMP connectivity. Moreover, the R1 Extender has a built-in 23dBi planar antenna that
can deliver up to a 40Km connection. With high throughput and long-distance transmission,
the R1 Extender is an ideal backhaul solution for Carriers, Service Providers and Enterprises!
Chapter 1 Introduction
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Preparation before Installation
This chapter describes safety precautions and product information you have to know and
check before installing R1 Extender.
Professional Installation Required
1. Please seek assistance from a professional installer who is well trained in the RF
installation and knowledgeable in the local regulations.
2. The R1 Extender is distributed through distributor and system installer with professional
technicians and will not be sold directly through retail store.
Safety Precautions
To keep you safe and install the hardware properly, please read and follow these safety
precautions.
1. If you are installing an antenna for the first time, for your safety as well as others’, please
seek assistance from a professional installer who has received safety training on the
hazards involved.
2. Keep safety as well as performance in mind when selecting your installation site,
especially where there are electric power and phone lines.
3. When installing your antenna, note the following:
♦
♦
♦
Do not use a metal ladder;
Do not work on a wet or windy day;
Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
4. When the system is operational, avoid standing directly in front of the antenna. Strong RF
fields are present when the transmitter is on.
Chapter 2 Preparation before Installation
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Package
The product package you have received should contain the following items. If any of them are
not included or damaged, please contact your local vendor for support.
R1 Extender with integrated 23dBi antenna
Mounting Kit
×1
×1
×1
×1
×1
×1
×1
PoE Injector & Power cord
Grounding Wire with Screw
Water Proof RJ-45 Connector Kit
Quick Installation Guide
Product CD
Note:
Product CD contains Management Tool, Quick Installation Guide and User
Manual!
Mounting Kit
Wall/Pole Mounting Bracket
1. T-Form Bracket ×1
2. Articulation Pole ×1
3. Pole Mount Bar
Fasteners
×1
4. M8×80 Screw
M8×90 Screw
5. M8 Washer
×2
×1
×3
6. M8 Spring Washer ×3
7. M8 Nut
×1
×4
×4
8. M5×16 Screw
9. M5 Washer
Chapter 2 Preparation before Installation
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Wood Screw
×4 (for Wall Mount)
11. Wall/Gyprock Plug ×4 (for Wall Mount)
Waterproof RJ-45 Connector Kit
1. Gland
×1
×1
×1
2. Sealing Nut
3. Sealing
Chapter 2 Preparation before Installation
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 System Installation
Assemble the Mounting Bracket
1. Place the main bracket into the seating and use a spanner to fasten the bracket to the R1
Extender with M5×16 screws ⑧ and M5 washers ⑨ provided in the hardware packets;
2. Assemble the main bracket by placing articulation pole ② to the T-form bracket ① via a
M8×90 ④ screw through the insertion axe and fix with the M8 washer ⑤ , spring
washer ⑥ and M8 nut⑦;
Chapter 3 System Installation
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Pole Mounting
1. Install the main bracket and the pole mount bar ③ over the top of the pole by
securing the drill holes of the pole mount bar to the main bracket ones and insert two
M8×80 ④ screws, spring washers ⑥ and washers ⑤ through the drill holes and
main bracket;
2. Fasten two M8×80 screws ④ and washers ⑤ through the drill holes and main
bracket with a spanner;
3. Adjust the antenna for appropriate tilt / vertical orientation.
Chapter 3 System Installation
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect Up
Before installing the Ethernet cable with a waterproof RJ-45 connector, it is recommended that
the Cat-5 RJ-45 coaxial cable be used for the bridge to power injector connections.
1. To connect to the hole labeled PoE+Data, open the black cover in advance by using a
coin or a slotted screwdriver and then screw in the body of the gland and tighten.
2. Slide the sealing nut to the RJ-45 cable from its middle breach and then insert the sealing
into the cable.
Slide the Sealing Nut from its Breach
3. Insert the RJ-45 connector and make sure that the locking tab snaps home.
R1 Extender RJ-45 Port
4. Screw the sealing on the gland and tighten.
Chapter 3 System Installation
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Ground the wire
The R1 Extender is shipped with a grounding wire. The unit must be properly grounded to
protect against power surges. The grounding point can be found on the bottom of the unit. It is
supplied with an appropriate grounding lug for attachment to the ODU.
Power On
To power up the R1 Extender, follow the steps bellow:
1. Plug a user-supplied Cat-5 Ethernet cable from your wired LAN (or a computer) into the
power injector RJ-45 jack (DATA IN);
2. Plug a user-supplied Cat-5 Ethernet cable from the R1 Extender into the power injector
RJ-45 jack (P+DATA OUT);
3. Connect the power module to the power injector and plug the AC cord into an AC power
receptacle.
4. After being powered on, the device will send out the beep sound lasting about 1.5
seconds, informing you that the R1 Extender powered up! Wait for about 60 seconds the
system will be initialized and start working.
Chapter 3 System Installation
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning:
Make sure PoE is correctly connected to the RJ-45 port on the R1 Extender
labeled PoE+Data. DO NOT connect to the port labeled “Warning!! No POE”,
otherwise the extender will be severely damaged!
Chapter 3 System Installation
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Configuration
Connect the R1 Extender to a Local Computer
If you are configuring the R1 Extender locally (without connecting its power injector to a wired
LAN), connect a PC to the power injector’s Ethernet port using a Category 5 Ethernet cable.
1. Assign a static IP address to your PC which is in the same network segment with the R1
Extender. As the default IP address of this unit is 192.168.1.1, you may choose from
192.168.1.2 to 192.168.1.254.
2. Test the link status between your PC and the R1 Extender. Start a command prompt and
execute a continuous ping command “ping 192.168.1.1 –t”. If ping to the wireless bridge is
successful (as shown below), open Internet browser and enter the bridge’s IP address in
the address filed and press Enter.
Chapter 4 Configuration
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
R1 Extender’s still initializing
System ready
Note:
Considering convenient configuration, it is recommended to configure local
and remote R1 Extender respectively on two computers.
TTL time may vary depending on the operating system.
Chapter 4 Configuration
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Establish Wireless Bridge Mode
The R1 Extender supports four operating modes, which are Base Station, CPE, Peer-to-Peer
(CSMA) and Peer-to-Peer (TDMA). Normally, Wireless Bridge is the typical mode on this unit.
Here we will illustrate how to establish wireless bridge connectivity with R1 Extender.
Enter the user name (admin) and password (password) to login and make configurations.
Note:
Due to browser’s security trusted sites, 192.168.1.1 might not able to be opened.
You may choose to continue to the website.
Open “Basic Setup” in “System”, set the IP address of two R1 Extenders in the same
network segment. e.g. local R1 Extender as 192.168.1.1 and remote R1 Extender as
Chapter 4 Configuration
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
192.168.1.2 and set the IP Subnet Mask on both as 255.255.255.0
Warning:
Each IP address is unique within a LAN, otherwise IP collision may occur!
Open “Radio” in “Wireless” and you will find the default operating mode is Peer-to-Peer
(CSMA). Select to use the Peer-to-Peer (CSMA) operating mode and keep the
Channel/Frequency and Bandwidth on both R1 Extenders identical. Click “Apply” to
save settings.
Chapter 4 Configuration
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Login the Web-based interface of remote R1 Extender, open “About” in “System” and
record the wireless MAC address of it.
Login the Web-based interface of local R1 Extender and open “Peer-to-Peer Setup” in
“Wireless”, input the WLAN MAC address of the remote one to “Remote MAC Address
1” field and click “Apply”;
Chapter 4 Configuration
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning:
The MAC address on the housing of R1 Extender is the ETH MAC address;
therefore it can not be used in Peer-to-Peer links.
The IP address of your PC should be in the same network segment to the one
of bridges.
Use ping to check whether the link between the two R1 Extender is OK.
R1 Extender A
R1 Extender B
To get a better wireless connectivity, antenna alignment is strongly recommended after
Chapter 4 Configuration
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
both R1 Extenders are installed long distance apart.
Login the Web-based interface of the local R1 Extender and open “Peer-to-Peer Setup”
in “Wireless”. Hit “Align Antenna” button, an antenna alignment tool will popup. Specify
the Target RSSI and click “Start” to begin the antenna alignment.
Fix the local antenna and adjust the remote antenna elevation and horizontal direction.
During the adjustment, observe “Current RSSI” in local R1 Extender. Fix the remote
antenna when it reaches your expectation. Usually, RSSI between -60 and -70dBm
indicates rather good signal strength.
Adjust the local antenna after fixing the remote one. During the adjustment, observe
“Current RSSI” in the remote R1 Extender. Fix the local antenna when it reaches your
expectation.
Congratulations! You have primarily completed configuration on R1 Extender and they can be
put into operation. For more advanced configurations, please refer to the User manual.
Chapter 4 Configuration
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Troubleshooting
This chapter provides troubleshooting procedures for basic problems with the R1 Extender.
Q 1.What if my R1 Extender fails to connect to the remote one?
•
Ethernet Link: Check the availability of power to the bridge by observing the LED
status on the power injector.
-
Green: The R1 Extender is connecting to the backhaul network.
-
Off: The R1 Extender disconnects from the wired network, check whether the power
cord and Ethernet cables to the network and bridge are correctly connected.
Basic Configurations: Mismatched basic settings among bridges are the most
common cause of connectivity fail. If the bridge does not associate with a remote
bridge, check whether options in each device are identical.
•
•
•
Security Settings: Remote bridges attempting to authenticate to your R1 Extender
must support the same security options configured in your bridge, such as WEP and
WPA (2)-PSK. If your bridge fails to associate with others, check whether the security
settings are the same as your bridge settings.
Antenna Alignment: If the methods above are all checked to be correct, you can
observe and verify antenna alignment with RSSI value.
Q 2.What if I would like to reset the unit to default settings?
You may restore factory default settings in “Backup/Restore Settings” from “Management”
Q 3.What if I would like to backup and restore my configuration settings?
You may do the backup by generating a configuration file or retrieve the settings you have
backed up previously in “Backup/Restore Settings” from “Management”.
Chapter 6 Service Information
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Service Information
If you have any further trouble using the R2 Extender or you would like to require additional
for support:
Z-Com, Inc.
Taiwan
7F-2, No.9. Prosperity Tel: +886-3-5777364
Science-Based Fax:+886-3-5773359
Sales Contact
Business RD.
I
FAE Support
Center
Industrial Park
Hsinchu ,300 Taiwan
Zcomax Technologies, Inc.
California 14545 Valley View Ave., Tel: +1-562-926-4588
Sales/Product Inquiries:
Tech Support/Questions:
Business Suite "S"
Fax:+1-562-926-7885
Center
Santa Fe Springs, CA
90670
New
98 Ford Road, Suite 3-F,
Denville, NJ 07834, USA
Tel: +1-973-664-0310
Fax:+1-973-664-0313
Jersey
Business
Center
ZCOMAX - United Kingdom Limited
European 19 Colindale Avenue Tel:+44-(0)-20-8982-8200 Sales Contact
Business London NW9 5DS UK
Centre
Fax:+44-(0)-20-8201-3232 [email protected]
FAE Support
Z-Dotcom, Inc
China
168 Long Pan Zhong Tel: +86-25-84661300
Sales Contact
Business Road, Jiangsu Software Fax:+86-25-84661313
FAE Support
Centre
Park, Suite 118 Nanjing,
China 210002
Chapter 6 Service Information
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
|